Trim Phone
with Caller ID
OWNER’S MANUAL —
43-3909
Please read before using this equipment.
RINGER ON/OFF — Slide to
the desired setting to enable
or disable the ringer when
you receive a call.
MUTE — Hold
down to talk
without the caller
hearing your
conversation.
VOLUME NORM/HI
— Slide VOLUME to
NORM or HI to
adjust the handset
volume to a
comfortable listening
level.
Liquid Crystal Display —
Shows the caller’s phone
number, the time they called,
and the number you dial.
FLASH — If you
have Call Waiting,
press FLASH to
answer an incoming
call without
TONE/PULSE — Slide
to the desired setting to
select tone or pulse
dialing.
disconnecting the
current call. Press
again to return to the
first call.
CALL BACK — Press to
automatically dial the
selected caller ID record.
d REVIEW e — Press
d or e to scroll through the
stored caller ID records.
REDIAL/PAUSE —
Press to dial the last
phone number you
entered.
DELETE — Press to
delete the selected caller
ID record.
Modular jacks
for coiled cord
SELECTING A LOCATION
Ô BATTERY NOTES Ô
PREPARATION
• Dispose of old batteries promptly and
properly.
Select a location for your telephone that is:
INSTALLING BATTERIES
• Do not burn or bury batteries.
• Near a telephone jack
Your phone requires three AA batteries (not
• Use only fresh batteries of the required size
and recommended type.
• Not in the way of normal activities
supplied) for power. Ô
• Do not mix old and new batteries, different
types of batteries (standard, alkaline, or
rechargeable), or rechargeable batteries of
different capacities.
1. Use a flat-blade screwdriver to lift and
remove the battery compartment door.
MOUNTING THE PHONE
You can mount your telephone on a wall
plate, on a wall, or place it on a shelf, desk,
or table.
2. Insert three AA batteries into the
compartment as indicated by the
polarity symbols (+ and –) marked
inside.
• If you do not plan to use the phone for two
weeks or longer, remove the batteries.
Batteries can leak chemicals that can
destroy electronic parts.
On a Wall Plate
1. Plug one end
of the supplied
short modular
cord into the
• You must install the batteries before
connecting the telephone to the wall jack. If
no batteries are installed, the telephone and
Caller ID will not work.
• If the batteries are not replaced with two
minutes, the Caller ID and telephone
memory information may be lost.
modular jack
on the back of
the phone.
2. Route the cord
through the
groove on the
bottom of the base. Secure the cord
with the tabs.
3. Snap the battery compartment door
back into place. When ) appears on
the display or the display dims, replace
the batteries.
3. Plug the other end of the cord into a
wall plate with a modular phone jack.
On a Wall
1. Drill two holes 31/4 inches (82.5 mm)
apart, one below the other.
2. Thread two screws (not supplied) into
each hole, letting the heads extend
about 3/16 inch from the wall. Be sure to
IMPORTANT
!
!
© 2003 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by
RadioShack Corporation.
If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon
for pertinent information.
— Warning
— Important
Ô — Note
ꢀ— Caution
Ó — Hint
!
o
Download from Www.Somanuals.com. All Manuals Search And Download.
RECEIVING A CALL
CALL BACK FROM
When you receive a call, the phone rings
and NEW flashes. NEW and the caller’s
number appear on the display. To answer
the call, pick up the handset. NEW flashes
until you have reviewed all calls.
CALLER ID MEMORY
1. With the handset on the base, press d
or e to find the number to redial.
2. Press CALL BACK twice. PICK UP CALL
appears.
TIMER
3. Lift the handset, and the number is
automatically redialed.
This unit is designed with a clock timer to
count up to 60 minutes in the off-hook time
(in 00:00 format). The timer appears on the
display and starts to count up when you dial
a number or answer incoming calls.
Select one of the four options below based
on your telephone company’s requirements
to make toll calls within your area code.
Ô NOTE Ô
• If you do not have any special phone
services, pressing FLASH might disconnect
the current call.
If you lift the handset and don’t dial a
number, the timer appears and starts to
count up after 10 seconds.
Option1
1 + Area Code + 7-digit number (11 digits)
Using Pause
Option 2
1 + 7-digit number (8 digits)
• Redial memory holds up to 32 digits, so you
can redial long distance, as well as local
phone numbers.
USING PAUSE
When you manually dial a number, you can
have your telephone pause anywhere during
the dialing sequence. Simply press
REDIAL/PAUSE at the desired location, and P
appears on the display next to the dialed
number. Ô
• When you redial a number, the telephone
pauses for about four seconds at the pause
entry. For long pauses, press
Option 3
Area Code + 7-digit number (10 digits)
REDIAL/PAUSE again.
Option 4
7-digit number
Caller ID Operation
• During an incoming call, the phone company
automatically sends the correct time
between the first and second rings to update
your system’s display.
1. With the handset on the base, press d
CALLER ID
or e to find the number to redial.
OPERATION
• After reviewing all calls, the system resets so
that the display shows 0 new calls.
2. Press CALL BACK. The 7- or 11-digit
If you subscribe to a Caller ID service, the
phone automatically displays information
about calls you receive and stores the
information in memory. The system can
store up to 64 incoming phone numbers and
incoming names into call records. Ô
number flashes.
Call Back from Caller ID Memory
• When the caller’s phone number has a
different area code from the preset area
code, 1 and the caller’s three digit area code
are inserted automatically during memory
call back.
3. Press d or e to select one of the above
four options.
4. Press CALL BACK again to confirm. Ô
• When the caller’s phone number has the
same area code as the preset one, 1 and the
three digit area code are deleted
5. Pick up the handset, and the selected
number is dialed automatically.
REVIEWING CALL RECORDS
1. Repeatedly press d or e to review the
new calls. END OF NEW CALL appears
when all calls have been reviewed.
automatically during the memory call back.
Deleting Call Records
DELETING CALL RECORDS
• When the phone’s memory is full, it
automatically replaces the oldest call record
with the newest incoming call.
You can delete an individual call record, or
2. To review all the records from oldest to
all call records stored in the system. Ô
newest, repeatedly press REVIEW e.
• If you do not press any button within about
15 seconds while the display shows ERASE
ALL CALLS, the phone automatically returns
to normal display and the call records are not
deleted.
To delete a single call record, press d or e
until the call record you want to delete
appears, then press DELETE twice. The
record is deleted, and the remaining call
records are automatically renumbered.
To review the records from newest to
oldest, repeatedly press d REVIEW.
After reviewing all records in memory,
END OF LIST appears.
3. If an incorrect, invalid or incomplete
Caller ID signal is received, LINE ERROR
appears on the display.
To delete all of the call records after
reviewing all new calls, hold down DELETE
for about three seconds. ERASE ALL CALLS
appears. Press DELETE. The system deletes
all call records, NO CALLS appear, then
TOTAL:00 NEW:00 appears.
If the name and number are not
available due to the caller’s restriction,
PRIVATE CALL appears on the display.
If the name and number are not
available, –UNAVAILABLE- appears on the
display.
FCC STATEMENT
This phone is hearing aid compatible.
Your telephone complies with Part 68 of FCC Rules and
the requirements adopted by the ACTA. On the back of
this product is a label with this product’s FCC Product
Identification number in the format DYFMT08B433909. If
requested, you must provide this information to the
telephone company.
RPT appears beside a number if you
have received a call from the same
phone number more than once.
4. If you do not press a button within about
15 seconds, the system automatically
returns to the normal display. Ô
Note: You must not connect your telephone to:
•
•
•
coin-operated systems
most electronic key telephone systems
party-line systems
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to party line service is subject to state tariffs.
Contact the state public utility commission, public service
commission, or corporation commission for information.
•
•
Consult your local RadioShack store or an
experienced radio/TV technician for help.
Ô NOTE Ô
Surge Protection
If you cannot eliminate the interference, the FCC
requires that you stop using your telephone.
We have designed your telephone to conform to federal
regulations, and you can connect it to most telephone
lines. However, each telephone (and each device, such
as a telephone or answering machine) that you connect
to the telephone line draws power from the telephone
line. We refer to this power draw as the device's ringer
equivalence number, or REN. The REN for your
telephone is the digits represented by ##, without a
decimal point (e.g., 03 is a REN of o.3), in the Product
Identification number found on the bottom of your
telephone.
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
Changes or modifications not expressly approved by
RadioShack may cause interference and void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Lightning damage is not common.
Nevertheless, if you live in an area that has
severe electrical storms, we suggest that you
unplug your phone when storms approach to
reduce the possibility of damage.
If you use more than one phone or other device on the
line, add up all of the RENs. If the total is more than five
(three in rural areas), your telephones might not ring. If
ringer operation is impaired, remove a device from the
line.
SETUP
In the unlikely event that your phone causes problems on
the phone line, the phone company can temporarily
discontinue your service. If this happens, the phone
company attempts to notify you in advance. If advance
notice is not practical, the phone company notifies you as
soon as possible and advises you of your right to file a
complaint with the FCC.
Your telephone connects directly to a modular telephone
line jack. If your telephone wiring does not have a
modular jack, you can update the wiring yourself using
jacks and adapters (available at your local RadioShack
store), or have the telephone company update the wiring
for you. You must use compatible modular jacks that are
compliant with Part 68 of FCC Rules and the
requirements adopted by the ACTA. The telephone cord
and modular plug provided is Part 68 compliant for
connecting to the telephone company network.
Also, the phone company can make changes to its lines,
equipment, operations, or procedures that could affect
the operation of this telephone. The telephone company
notifies you of these changes in advance, so you can
take the necessary steps to prevent interruption of your
telephone service.
Note: The USOC number of the jack to be installed is
RJ11C (or RJ11W for a wall plate jack).
If your home has specially wired alarm equipment
connected to the telephone line, be sure that installing
the telephone does not disable your alarm equipment. If
you have questions about what will disable your alarm
equipment, contact your telephone company or a
qualified installer.
THE FCC WANTS YOU
TO KNOW
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
SERVICE AND REPAIR
If your telephone is not performing as it should, take it to
your local RadioShack store for assistance. To locate
your nearest RadioShack, use the store locator feature
1-800-The Shack (843-7422) and follow the menu
options. Modifying or tampering with the telephone's
internal components can cause a malfunction and might
invalidate its warranty and void your FCC authorization to
operate it.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1)
year from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers. EX-
CEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURA-
TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIA-
BILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCON-
VENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase
date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair
without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All
replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned
parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for
the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of
the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or ab-
normal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess
voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation,
set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
43-3909
05A03
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
Download from Www.Somanuals.com. All Manuals Search And Download.
|