Cat. No. 43-1118
OWNER’S MANUAL
Please read before using this equipment.
ET-1118
900 MHz Digital Spread Spectrum Cordless
Telephone with Caller ID and Call Waiting ID
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Access-Protection Code —
automatically prevents other cordless
phone users from using your phone line
while the handset is off the base.
IMPORTANT CALLER ID
INFORMATION
To use the phone’s Caller ID and Caller
ID with Call Waiting features, you must
be in an area where those services are
available and you must subscribe to
those services through your local phone
company.
Redial — lets you quickly redial the last
number dialed.
Flash — sends an electronic switch-
hook signal for use with special phone
services, such as Call Waiting.
Where Caller ID is offered, one or more
options are generally available:
Tone/Pulse Dialing — lets you use ei-
ther type of service, and you can easily
switch from pulse to tone dialing for
long-distance, bank-by-phone, or other
special services.
• caller’s number only
• caller’s name only
• caller’s name and number
Auto Talk — lets you set the handset so
you can answer a call by simply lifting
the handset from the base or by press-
ing any key when the handset is away
from the base.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
Hearing-Aid Compatibility — lets you
use your phone with hearing aids that
have a T (telephone) switch.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This telephone is UL listed and has
been tested and found to comply with all
applicable FCC standards.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
We recommend you record your
phone’s serial number here. The num-
ber is on the bottom of the base.
Serial Number __________________
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important:
FCC STATEMENT
• Cordless phones such as this one
require AC power to operate. When
the AC power is off, you cannot dial
out or receive incoming calls using
your ET-1118. To be safe, you
should also have a phone that does
not need AC power to operate (not a
cordless phone) so you can still
make and receive calls if there is an
AC power failure.
This telephone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number
and the REN to your phone company.
These numbers are on the bottom of the
base.
Note: You must not connect your phone
to any of the following:
• coin-operated systems
• When AC power is lost, the ET-1118
loses the security access-protection
code connection between the base
and the handset. When power is
restored, put the handset on the
base briefly to restore this connec-
tion so you can use the handset.
• party-line systems
• most electronic key phone systems
This phone complies with the limits for a
Class B digital device as specified in
Part 15 of FCC Rules. These limits pro-
vide reasonable protection against ra-
dio and TV interference in a residential
area. However, your equipment might
cause TV or radio interference even
when it is operating properly. To elimi-
nate interference, you can try one or
more of the following corrective mea-
sures.
READ THIS BEFORE
INSTALLATION
Each device that you connect to the
phone line draws power from the phone
line. We refer to this power draw as the
device’s ringer equivalence number, or
REN. The REN is on the bottom of the
base.
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and the radio or TV.
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five, your
phones might not ring. In rural areas, a
total REN of three might impair ringer
operation. If ringer operation is impaired,
remove a device from the line.
• Use outlets on different electrical cir-
cuits for the equipment and the
radio or TV.
Consult your local RadioShack store if
the problem still exists.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Installation ............................................................................................................... 7
Mounting the Phone ........................................................................................... 7
On a Desk Top ............................................................................................. 7
On a Wall Plate or Wall ................................................................................ 8
Connecting and Charging the Battery Pack ..................................................... 10
Setting the Dialing Mode .................................................................................. 11
Setting the Ringers’ Volume ...................................................................... 11
Using Auto Talk ................................................................................................ 12
Turning Caller ID/Call Waiting On/Off ............................................................... 12
Storing Your Area Code ................................................................................... 13
Telephone Operation ............................................................................................ 14
Making and Receiving Calls with the Handset ................................................. 14
Adjusting the Handset Volume ......................................................................... 14
Making and Receiving Calls with the Speakerphone ....................................... 14
Switching Between the Handset and Speaker ................................................. 14
Using Both the Handset and Speakerphone .................................................... 15
Using Hold ........................................................................................................ 15
Using Mute ....................................................................................................... 15
Using Redial ..................................................................................................... 15
Using Flash ...................................................................................................... 16
Using Tone Services on a Pulse Line ............................................................... 16
Using Page/Intercom ........................................................................................ 16
Transferring a Call between the Handset and Base .................................. 17
Memory Dialing ................................................................................................ 17
Storing a Number in the Handset’s Memory .............................................. 18
Editing or Deleting a Number in the Handset’s Memory ............................ 19
Storing a Number in the Base’s Memory ................................................... 19
Entering a Pause ....................................................................................... 20
Reviewing Memory Numbers (Handset Only) ........................................... 20
Dialing a Memory Number ......................................................................... 20
Chain-Dialing Service Numbers ................................................................. 20
Testing Stored Emergency Numbers ......................................................... 21
Using a Headset ............................................................................................... 21
Caller ID Operation ............................................................................................... 22
Reviewing Caller ID Records ........................................................................... 22
Caller ID Messages ................................................................................... 23
Dialing Numbers from a Caller ID Record ........................................................ 23
Storing a Caller ID Record to the Handset’s Memory ...................................... 23
Deleting Caller ID Records ............................................................................... 24
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting .................................................................................................... 25
Care and Maintenance .......................................................................................... 27
Replacing the Battery Pack .............................................................................. 28
The FCC Wants You to Know ........................................................................... 29
Lightning ........................................................................................................... 29
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Notes:
• Your telephone connects directly to
MOUNTING THE PHONE
You can place the ET-1118’s base on a
desk or table, mount it on a standard
wall plate, or mount it directly on a wall.
Choose a location that is:
a modular telephone line jack. If
your phone line jack is not a modu-
lar jack, you can update the wiring
yourself, using jacks and adapters
available at your local RadioShack
store. Or, you can let the phone
company update the wiring for you.
• near an AC outlet
• near a modular telephone line jack
• out of the way of normal activities
• The USOC number of the jack to be
installed is RJ11C (RJ11W for a wall
plate).
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
On a Desk Top
• away from other cordless phones
1. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
The base’s location affects the phone’s
range. If you have a choice of several lo-
cations, try each to see which provides
the best performance.
Cautions:
You must use a Class 2
power source that supplies
!
9 volts AC and delivers at
least 500 mA. Its center tip must be
set to positive and its plug must fit
the ET-1118's DC IN 9V jack. The
supplied adapter meets these speci-
fications. Using an adapter that
does not meet these specifications
could damage the ET-1118 or the
adapter.
2. Plug the modular cord’s other end
into a modular telephone line jack.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
• Always connect the AC adapter to
the ET-1118 before you connect it to
AC power. When you finish, discon-
nect the adapter from AC power be-
fore you disconnect it from the ET-
1118.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Route the adapter’s cord through
the strain relief slot on the bottom of
the base.
2. Plug one end of the supplied short
modular cord into the TEL LINE jack
on the back of the base.
RING VOL
OFF-LO-HI
5. Plug the adapter into a standard AC
outlet.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack.
6. Lift the base’s antenna to a vertical
position.
On a Wall Plate or Wall
1. Insert the two tabs at the top of the
narrow end of the supplied bracket
into the base’s upper tab slots as
shown, then press down on the
bracket’s latches and insert them
into the lower slots.
4. Route the adapter and modular
cords through the grooves on the
bracket.
RING VOL
OFF-LO-HI
RING VOL
OFF-LO-HI
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Plug the modular cord’s other end
into the wall plate jack, then align
the bracket’s keyhole slots with the
wall plate studs and slide the base
downward to secure it.
additional instructions for placement on
a wall.
15
1. Drill two holes 3 /16
inches
(100
mm)
apart. Then thread a
screw into each hole,
letting
extend about /32 inch
(3 mm) from the wall.
the
heads
3
2. Plug one end of the supplied long
modular cord into the TEL LINE jack
at the back of the base.
RING VOL
OFF-LO-HI
6. Plug the adapter into a standard AC
outlet.
7. Press and lift out the handset
holder, flip it over as shown, then
snap it back into place so it holds
the handset.
3. Align the bracket’s keyhole slots
with the mounting screws and slide
the base downward to secure it.
8. Lift the base’s antenna to a vertical
position.
Note: To mount the phone directly on a
wall, you need two screws (not supplied)
with heads that fit into the keyhole slots
on the bottom of the base.
Follow Steps 1, 3, 4, and 6–8 under “On
a Wall Plate or Wall,” then follow these
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Recharge the battery pack when Low
Batteryflashes on the display.
CONNECTING AND
CHARGING THE BATTERY
PACK
Important: Be sure the battery pack is
properly connected before you try to
charge it. The CHARGE indicator lights
when the handset is on the base, even if
the battery pack is not connected.
The ET-1118 comes with a recharge-
able nickel-cadmium battery pack in the
handset but not connected. Before using
your phone, you must connect the bat-
tery pack and then charge it for about 24
hours.
Notes:
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear an error tone when
you press TALK. If this happens,
return the handset to the base for
about 5 seconds. This resets the
security access-protection code.
1. Press down and slide off the battery
pack compartment cover as shown.
• If the base loses power for 60 min-
utes while the handset is away from
it or the handset’s battery pack is
completely discharged, the security
access-protection code might be
lost. To reset the code, return the
handset to the base for about 5 sec-
onds.
2. Lift the battery pack out of the com-
partment.
3. Plug the battery pack’s connector
into the socket in the compartment
(the connector fits only one way),
then replace the battery pack.
• Using a pencil eraser, clean the
charging contacts on the handset
and the base about once a month.
4. Replace the cover.
To charge the battery pack, place the
handset on the base either faceup or
facedown. The CHARGE indicator on
the base lights and Total:00appears
on the handset display.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
• If the battery pack becomes weak
during a call, the handset beeps
every 3 seconds and Low Bat-
tery flashes. If this happens, you
cannot make another call on the
phone until you recharge the battery
pack.
the battery pack is fully charged, do this
test.
1. Be sure DIAL MODE is set to T
(tone).
DIAL MODE
• About once a month, fully discharge
the battery pack by keeping the
handset off the base until Low
Battery flashes. Otherwise, the
battery pack loses its ability to fully
recharge.
2. Lift the handset, press TALK, and
listen for a dial tone.
TALK
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be
too low to light the display.)
• If you are not going to use your
phone for an extended period of
time, disconnect the battery pack.
This increases the battery pack’s
usable life.
3. Press any number except 0.
Note: If your phone system requires that
you dial an access code (9, for example)
before you dial an outside number, do
not press the access code number ei-
ther.
• The supplied battery pack should
last for about a year. When it loses
its ability to fully recharge, order a
replacement battery pack from your
local RadioShack store (see
“Replacing the Battery Pack” on
Page 28).
If the dial tone stops, you have touch-
tone service. Leave DIAL MODE set to T.
If the dial tone continues, you have
pulse service. Set DIAL MODE to P
(pulse).
SETTING THE DIALING
MODE
Setting the Ringers’ Volume
Set DIAL MODE on the back of the base
for the type of service you have. If you
are not sure which type you have, once
The ET-1118 lets you set different vol-
umes for the handset and base ringers.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
At any time except during a call, press
or to set the handset’s ringer vol-
pressing any key when the handset is
away from the base.
ume. The phone rings at the selected
volume and the display shows Ringer
Lowor RingerHigh.
Follow these steps to turn auto talk on or
off.
1. Lift the handset then hold down
CALL ID. A menu appears with
AutoTalkselected.
CALL ID
To set the base’s ringer volume, set
RING VOL on the back of the base to
OFF, LO, or HI. When you set RING VOL
to OFF, the base (and the handset if it is
on the base) does not ring but the other
phone connected to the same line rings.
If the handset is away from the base, the
handset also rings.
SELECT
2. Press SELECT to change the auto
talk setting. On or Off appears
indicating the selected setting.
3. To clear the display, press CALL ID
or return the handset to the base.
RING VOL
TURNING CALLER ID/
CALL WAITING ON/OFF
If you have Call Waiting with Caller ID
service, you can set the ET-1118 to
show Caller ID information for an incom-
ing call even while you are already on
the phone.
Note: When you set the auto talk func-
tion to off, the handset rings when you
lift the handset from the base. See “Us-
ing Auto Talk.”
Follow these steps to turn the Caller ID/
Call Waiting feature on or off.
USING AUTO TALK
Your phone is preset so you must press
TALK when you lift the handset from the
base to answer a call. With auto talk
turned on, you can answer a call by just
lifting the handset from the base or by
1. Lift the handset then hold down
CALL ID.
2. Press 2 or
to select CIDCW
(Caller ID/Call Waiting).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press SELECT to change the Caller
ID/Call Waiting setting. On or Off
appears indicating the selected set-
ting.
three times. Then enter your area
code.
4. Press CALL ID or return the handset
to the base to store the new setting.
DELETE
STORING YOUR AREA
CODE
4. Press SELECT to store the area
To quickly dial a number from a Caller
ID record (see “Dialing Numbers from a
Caller ID Record” on Page 23) or to cor-
rectly store a number from a record into
a memory dialing location (see “Storing
a Caller ID Record to the Handset’s
Memory” on Page 23), you must store
your local area code in the ET-1118’s
memory. Then, when you dial from a
Caller ID record, the ET-1118 skips the
area code if it matches the one you
stored.
code.
5. To clear the display when you finish,
press CALL ID or return the handset
to the base.
Follow these steps to store your area
code.
1. Lift the handset then hold down
CALL ID.
2. Press 3 (or
twice) to select Area
Code.
3. Press SELECT, then enter your 3-
digit area code. If you make a mis-
take, repeatedly press or
to
move the cursor over the incorrect
digit, then enter the correct number.
Note: If an area code is already
stored, it appears on the display. To
delete the area code, press DELETE
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEPHONE OPERATION
MAKING AND RECEIVING
CALLS WITH THE
HANDSET
MAKING AND RECEIVING
CALLS WITH THE
SPEAKERPHONE
To make a call, lift the handset, then
press TALK. The IN USE indicator on
the base lights. Dial the number. You
see the number as you dial, then (about
5 seconds later) the call’s elapsed time.
To make or answer a call using the
speakerphone, press SPEAKER. The
SPEAKER indicator lights. When you
hear a dial tone, dial the number.
SPEAKER
Note: You can also dial the number be-
fore you press TALK. If you make a mis-
take, repeatedly press DELETE until the
incorrect digit is deleted, then enter the
correct number. To delete the entire
number, hold down DELETE for over one
second.
VOLUME
To answer a call, lift the handset from
the base and press TALK. If auto talk is
on, just lift the handset from the base,
or, if the handset is away from the base,
press any key to answer a call.
To set the speakerphone’s volume, slide
VOLUME on the right side of the base.
To end a speakerphone call, press
SPEAKER again.
To end a call, place the handset on the
base or press TALK.
SWITCHING BETWEEN
THE HANDSET AND
SPEAKER
ADJUSTING THE
HANDSET VOLUME
To adjust the volume of the sound you
hear through the handset, during a call,
press or . The display shows Vol-
umeLow, VolumeMedium, Volume
High, or Volume Maximum. When
you press when the volume is maxi-
To switch to the speakerphone while
you are using the handset, press
SPEAKER on the base. When you hear
the conversation or dial tone on the
speakerphone, press TALK on the hand-
set.
mum or
when the volume is low, the
error tone sounds.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To switch to the handset while you are
using the speakerphone, simply lift the
handset off the base. If the handset is
away from the base, press TALK, then
press SPEAKER.
To release a call from hold, lift the hand-
set and press TALK, press SPEAKER or
HOLD on the base, or pick up any exten-
sion phone on the same line.
MUTE
USING BOTH THE
HANDSET AND
SPEAKERPHONE
If someone else is using the speaker-
phone, press TALK on the handset to
join the conversation.
HOLD
If someone else is using the handset,
press SPEAKER on the base to join the
conversation.
USING MUTE
While talking on the speakerphone, you
can temporarily turn off the ET-1118’s
microphone by pressing MUTE so the
other party cannot hear you. The
SPEAKER indicator flashes.
During the call, one person can hang up
and let the call continue at the other key-
pad. Or, both people can hang up at the
same time to end the call.
Note: If you hear a high-pitched noise
from the base’s speaker, the handset
and the base are too close together.
Press MUTE or SPEAKER to resume
your conversation.
USING REDIAL
USING HOLD
You can quickly dial the last number di-
aled. Press SPEAKER or lift the handset
and press TALK, then press REDIAL.
Press HOLD to put a speakerphone call
on hold. The HOLD indicator lights.
While a call is on hold, you can make an
intercom call (see “Using Page/Inter-
com” on Page 16) between the handset
and the base without disconnecting the
call.
Notes:
• You can also press REDIAL on the
handset first, then press TALK.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
• The redial memory for each keypad
is separate. You cannot redial a
number you dialed on the handset’s
keypad using REDIAL on the base’s
keypad, and vice versa.
USING TONE SERVICES
ON A PULSE LINE
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by following
these steps.
• The redial memory holds up to 32
digits, so you can redial long-dis-
tance as well as local numbers.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 20.
1. Be sure DIAL MODE is set to P.
2. Dial the service’s main number.
3. When the service answers, press
TONE ( ) on the handset (TONE on
the base). Any additional numbers
you dial are sent as tone signals.
4. When you hang up, the phone auto-
matically resets to pulse dialing.
FLASH
USING PAGE/INTERCOM
REDIAL
You can use the ET-1118 as a two-way
pager and intercom between the base
and the handset. This is useful if the
handset is away from the base and you
want to locate it, or if you want to have a
conversation between someone with the
handset and someone at the base.
USING FLASH
FLASH performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
INTCOM
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To page the base from the handset,
press INTCM. Paging Base appears,
and the base and handset ring. Press
SPEAKER or INTERCOM on the base to
answer the page. Intercom appears
on the handset’s display.
Transferring a Call between the
Handset and Base
You can use the ET-1118’s intercom
feature to transfer a call between the
handset and the base.
SPEAKER
To transfer a call from the handset to the
base, press INTCM. The call is put on
hold, and PagingBaseand Holdap-
pear. When the person at the base an-
swers, press TALK. The call is released
from hold and transferred to the base.
To return to handset use, press TALK
again.
INTERCOM
To transfer a call from the base to the
handset, press INTERCOM. The call is
put on hold, and Pagingand Holdap-
pear on the handset’s display. When the
person with the handset answers, press
SPEAKER. The call is released from hold
and transferred to the handset. To return
to base use, press SPEAKER again.
To page the handset from the base,
press INTERCOM. The handset and
base ring, and Pagingappears on the
handset’s display. Press TALK or INTCM
on the handset to answer the page. In-
tercomappears.
To end an intercom call, press TALK on
the handset, press SPEAKER on the
base, or hang up the handset.
MEMORY DIALING
You can store up to 20 numbers in
memory (10 each in the handset’s and
base’s memory), then dial a stored num-
ber by pressing a memory location num-
ber. You can also store a name with
each number in the handset’s memory.
If a call comes in during an intercom
conversation, either the person at the
base or the person at the handset can
answer the call. Press TALK on the
handset or SPEAKER on the base once
to end the intercom call, then press
TALK or SPEAKER again to answer the
incoming call.
Note: The intercom does not operate if
the party being paged is already on a
call.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the supplied memory directory
stickers to record your stored numbers.
Peel the backing from each sticker and
attach them to the phone as shown.
3. Choose a memory location (1–0) by
pressing a number or by repeatedly
pressing or
.
4. To store a name, press SELECT.
StoreNameappears.
If you do not want to enter a name,
skip to Step 6. <Memory n>
appears as the name (nis the mem-
ory location number you selected).
To enter a name, use
or
to
select the characters and or to
move the cursor.
Repeatedly press to see the char-
acters in alphabetical order. (The
display shows uppercase letters
first, then lowercase letters, num-
bers, and special characters.)
Storing a Number in the
Handset’s Memory
Each number stored in the handset’s
memory can be up to 20 digits, and each
name can be up to 14 characters.
Notes:
• Press
to see the characters in
reverse order.
Note: An error tone sounds and the
phone exits the storing process if you
wait more than 20 seconds between
each keypress.
• You can hold down
or
to
scroll rapidly through the charac-
ters.
If you make a mistake, move the
cursor over the error, then enter the
correct character, or press DELETE
to delete a character. To delete all
the characters, hold down DELETE
for at least 1 second.
1. Lift the handset.
2. Hold down MEM until Memory
Store and a list of memory loca-
tion numbers (and names, if any)
appear.
5. Press SELECT. Store Number
appears.
6. Enter the phone number and any
tone or pause entries (see “Using
Tone Services on a Pulse Line” on
Page 16 and “Entering a Pause” on
Page 20).
MEM
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Press SELECT. The phone beeps
and Memory n Stored appears.
After 2 seconds, Memory Store
appears, and you can repeat Steps
3–6 to store more numbers.
return the handset to the base to
exit the MemoryStoredisplay.
Storing a Number in the Base’s
Memory
To replace a stored number, simply
store a new one in its place.
Note: An error tone sounds and the
phone exits the storing process if you
wait more than 20 seconds between
each keypress.
Editing or Deleting a Number in
the Handset’s Memory
1. Press MEM. The IN USE indicator
1. Lift the handset.
blinks.
2. Hold down MEM until Memory
Store and a list of memory loca-
tion numbers appear on the display.
2. Enter the number (up to 16 digits)
and any tone or pause entries (see
“Using Tone Services on a Pulse
Line” on Page 16 and “Entering a
Pause” on Page 20).
3. Choose a memory location (0–9) by
pressing a number or by repeatedly
pressing or
4. Press SELECT. The options listed
below appear. Press or to
.
Notes:
• An error tone sounds and the
phone exits the storing process if
you enter more than 16 digits.
choose an option, follow the instruc-
tions listed, then press SELECT.
• Each tone or pause entry uses
one digit of memory.
EditMemoryn— Edit the record
as described in Steps 5 through 7 of
“Storing a Number in the Handset’s
Memory” on Page 16.
3. Press MEM again, then enter the
memory location number (0–9)
where you want to store the phone
number. A tone sounds indicating
that the number is stored.
DeleteMemoryn— The display
prompts you to confirm the deletion.
Move the cursor to Yes, then press
SELECT or DELETE. The phone
beeps, and Memory n Deleted
appears.
To replace a number in the base’s mem-
ory, simply store a new number in its
place. To erase a memory number,
press MEM twice, then press the memo-
ry location number (0–9) you want to
erase. A tone sounds indicating that the
memory location has been erased.
GoBack— Returns you to the list
of memory numbers.
5. When you finish editing or deleting
memory numbers, press MEM or
19
Download from Www.Somanuals.com. All Manuals Search And Download.
memory location number. To exit this
display, hold down DELETE until the dis-
play clears.
Entering a Pause
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect.
Dialing a Memory Number
To dial a number stored in the handset’s
memory, lift the handset and press MEM.
The list of memory location numbers ap-
pears. Choose a memory location (0–9)
by pressing a number or by repeatedly
pressing or , then press TALK.
To enter a 2-second pause, press
PAUSE (REDIAL/PAUSE on the handset).
Pappears on the display if you are stor-
ing a number into the handset’s memo-
ry. You can add more pause entries for
a longer pause.
To dial a number stored in the base’s
memory, press SPEAKER. When you
hear a dial tone, press MEM, then press
the memory location number for the
number you want to dial.
Reviewing Memory Numbers
(Handset Only)
Note: If you select an empty memory lo-
cation, the base beeps 5 times.
To review your memory numbers, press
MEM. The list of the first three memory
locations appears with the name stored
with each number (or <Memory n> if
you did not store a name). Press or
to scroll through the list if necessary.
Chain-Dialing Service Numbers
For quick recall of numbers for special
services (such as bank by phone), store
each group of numbers in its own mem-
ory location.
To see the stored phone numbers, press
. An arrow to the right of the number
indicates it is longer than 14 digits.
Dial the service’s main number first.
Then, at the appropriate place in the
call, press MEM and the number for the
location where the additional information
is stored.
Press
again to see the rest of the
number. Repeatedly press to return to
the name display.
To exit the memory number list, press
MEM.
To see a stored name and phone num-
ber at the same time, press SELECT
when the cursor is next to the desired
20
Download from Www.Somanuals.com. All Manuals Search And Download.
speakerphone or the keys on the hand-
set.
Testing Stored Emergency
Numbers
You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for great-
er convenience.
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
When you finish using the headset, dis-
connect it from the handset and close
the rubber cover to protect the jack.
USING A HEADSET
You can talk with hands-free conve-
nience using an optional headset that
3
has a /32-inch (2.5-mm) plug. Contact
your local RadioShack store for a suit-
able headset.
To connect the headset, open the rub-
ber cover marked
on the side of the
handset, then insert the headset’s plug
into the jack.
Notes:
• Connecting a headset disconnects
the handset’s earpiece and micro-
phone.
• VOL
.or
.on the handset also
controls the connected headset’s
volume.
• If you place the handset on the base
to recharge it while the headset is
connected, be sure the handset
seats properly.
With a headset connected, you can
make or answer calls as usual using the
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the phone compa-
ny sends information about the call, as
well as the time and date, between the
first and second rings of every call you
receive.
REVIEWING CALLER ID
RECORDS
To review the Caller ID records, lift the
handset and press CALL ID. The number
of new Caller ID records, if any, and the
total number of records appears.
The ET-1118 displays this information
when it receives a call, and it stores up
to 50 Caller ID records for later review. It
also shows if caller information is un-
available or if the name and number
were blocked by the caller (see “Caller
ID Messages” on Page 23).
CALL ID
If you subscribe to Call Waiting with
Caller ID, you will hear a tone through
the handset when a call comes in, then
the Caller ID record appears. If you want
to answer the incoming call, press
FLASH. To resume the previous phone
conversation, press FLASH again.
Note: If the handset is faceup on the
base, it always shows the number of
Caller ID records, so you can see if you
have new records to review.
Repeatedly press to scroll through
the Caller ID records from the newest to
the oldest, or
the records. To scroll quickly through the
records, hold down or
to scroll back through
FLASH
.
When you scroll past the oldest record,
Endappears. When you scroll past the
newest record, the record totals appear.
If the phone’s Caller ID memory be-
comes full, any new call replaces the
oldest call’s record.
The top line of each record shows the
date, time and the number of calls from
that number. The second line shows the
caller’s name, and the third line shows
the caller’s phone number.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID Messages
DIALING NUMBERS FROM
A CALLER ID RECORD
Display
Description
To dial a local number stored in a Caller
ID record, recall the record, then press
TALK. If it is a long distance call, press 1
(1 appears before the displayed num-
ber) before pressing TALK.
Shows the number
of new Caller ID
records (records you
have not reviewed)
and the total number
of records.
New:XX
Total:XX
Note: If a Caller ID record does not con-
tain a phone number (if it was blocked
by the caller) you cannot dial from that
record.
The caller has
blocked the Caller ID
information from
being sent.
Private
Name
Private
Number
The caller is not
within a Caller ID
service area.
Unknown
Name
Unknown
Number
STORING A CALLER ID
RECORD TO THE
HANDSET’S MEMORY
Follow these steps to store the name
and number from a Caller ID record into
a handset memory location.
Appears if there was
an error during the
transmission of
Caller ID informa-
tion. Minor electrical
disturbances can
affect Caller ID infor-
mation. Occasional
errors are normal. If
the phone fre-
Incomplete
Data
Note: To store a record from a Caller ID
record into the base memory, recall the
record, follow steps in “Storing a Num-
ber in the Base’s Memory” on Page 19.
1. Recall the record you want to store,
then press MEM. Select Loca-
tion appears.
quently displays
Incomplete Data,
contact your local
telephone company
or RadioShack store
for assistance.
2. Choose
a
memory location by
pressing its number (0–9) or scroll-
ing the list using
or , then press
Appears when you
scroll past the last
Caller ID record.
SELECT.
End
If the selected location is empty, the
phone beeps to confirm that it stored the
number, then the Caller ID record ap-
pears.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
If a record exists in the selected loca-
tion, Replace Memory? appears,
prompting you to confirm the replace-
ment. Move the cursor to Yes or No,
then press SELECT.
DELETING CALLER ID
RECORDS
You can delete Caller ID records individ-
ually or all at once.
To delete a single record, recall it, then
press DELETE. Delete Message?
appears, prompting you to confirm the
deletion. Move the cursor to Yesor No,
then press SELECT or DELETE.
To delete all the records at once, press
DELETE while the total number of
records is on the display. Delete
All? appears, prompting you to con-
firm the deletion. Move the cursor to
Yes or No, then press SELECT or DE-
LETE.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, the follow-
ing suggestions might help.
Problem
Suggestion
The phone does not work or works poorly.
Be sure the base’s phone line cord and AC
adapter are correctly and securely con-
nected.
Be sure the battery pack in the handset is
connected and charged.
Return the handset to the base for a few
seconds to reset the security access-protec-
tion code.
The display flashes slowly when the hand-
set is faceup on the base.
Be sure the battery pack in the handset is
properly connected.
The handset stops working or works poorly
during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical
position.
Be sure the handset’s battery pack is
charged. (If the battery pack power is too
low, it does not have enough power to light
on the display.)
LowBattery
Low volume or unusual sounds.
Severe noise interference.
Someone has picked up another phone on
the same line. Hang up the other phone.
Keep the handset away from computers,
remote control toys, wireless microphones,
alarm systems, intercoms, room monitors,
fluorescent lights, and electrical appliances.
Move to another location or turn off the
source of interference.
Hang up and redial the number.
The phone cannot be operated at a useful
distance from the base because the signal
becomes weak or noisy (handset’s range
has decreased).
Lift the base’s antenna to a fully vertical
position.
Be sure neither the handset’s nor base’s
antenna is touching a metal surface.
Recharge the battery pack.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Suggestion
The handset battery pack does not charge.
Check the charging contacts on the handset
and base. If they are dirty, clean them with a
pencil eraser.
Be sure the battery pack is properly con-
nected.
Be sure the handset is properly seated on
the base.
Replace the battery pack (see “Replacing
the Battery Pack” on Page 28).
The handset does not ring or receive a
page.
Lift the base’s antenna to a fully vertical
position.
Move the handset closer to the base.
Move the base away from other electrical
devices.
Recharge the battery pack.
You have an incoming call, but do not
receive any Caller ID information.
Let the phone ring twice before you answer
so the system has time to record the Caller
ID information.
Check that the system is correctly and
securely connected.
Call your phone company to verify that your
Caller ID service is active.
If you still have problems, disconnect the ET-1118. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your ET-1118 to your local RadioShack store for assistance.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
Your RadioShack
ET-1118 900 MHz Digital Spread Spectrum Cordless Telephone
is an example of superior design and craftsmanship. The following suggestions will
help you care for your ET-1118 so you can enjoy it for years.
Keep the ET-1118 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the ET-1118 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the ET-1118 away from dust and dirt, which can cause premature
wear of parts.
Handle the ET-1118 gently and carefully. Dropping it can damage circuit
boards and cases and can cause the ET-1118 to work improperly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your ET-1118’s electronic
parts.
Wipe the ET-1118 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the ET-1118.
Modifying or tampering with the ET-1118’s internal components can cause a mal-
function and might invalidate its warranty and void your FCC authorization to oper-
ate it. If your ET-1118 is not performing as it should, take it to your local RadioShack
store for assistance. If the trouble is affecting the telephone lines, the phone compa-
ny can ask you to disconnect your ET-1118 until you have resolved the problem.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not open or mutilate the battery
pack.
REPLACING THE
BATTERY PACK
• Be careful not to short the battery
pack by touching the connector’s
pins with conducting materials, such
as rings, bracelets, and keys. The
battery pack or conductor might
overheat and burn.
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 10, the battery pack should last
about one year. If the battery pack does
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a new 3.6-volt, 600 mAh battery pack
with a connector that fits the socket in
the battery compartment. You can order
a replacement battery pack through your
local RadioShack store.
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
Important: This tele-
phone can use nickel
Install the new battery pack as de-
scribed below, then charge it for about
24 hours.
cadmium rechargeable
batteries. At the end of a
nickel cadmium bat-
tery's useful life, it must
Note: To avoid losing redial memory
and the security code, begin charging
the new battery pack within 2 minutes.
be recycled or disposed
of properly. Contact your local, county,
or state hazardous waste management
authorities for information on recycling
or disposal programs in your area or call
1-800-843-7422. Some options that
might be available are: municipal curb-
side collection, drop-off boxes at retail-
ers such as your local RadioShack
store, recycling collection centers, and
mail-back programs.
1. Press down and slide off the battery
pack compartment cover.
2. Lift the battery pack out of the com-
partment, then gently pull on the
battery connector to disconnect it.
3. Insert the new battery pack’s con-
nector into the socket in the com-
partment, place the battery pack into
the compartment.
4. Replace the cover.
Cautions:
• You must use a replacement battery
pack of the same size and type.
• Do not dispose of the battery pack in
a fire because it might explode.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Some cordless telephones operate on
frequencies that might cause interfer-
ence to nearby TVs and VCRs. To mini-
mize or prevent such interference, the
base of the cordless telephone should
not be placed near or on top of a TV or
VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your telephone service.
Your telephone has built-in lightning pro-
tection to reduce the risk of damage
from surges in telephone line and power
line current. This lightning protection
meets or exceeds FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it. Try to
eliminate the interference by:
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
• moving your phone away from the
receiver
• connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• contacting your local RadioShack
store for help
29
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
30
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
04/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
UCZZ01641BX
07A99
Printed in the Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|