2.4 GHz Digital Spread
Spectrum Cordless
Telephone
with Call Waiting/Caller ID
Download from Www.Somanuals.com. All Manuals Search And Download.
only telephone. To be safe, you should also
have a phone that does not require AC pow-
er to operate (not a cordless phone) so you
can still make and receive calls if there is an
AC power failure.
Lightning
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
Some cordless phones operate at frequen-
cies that might cause interference to nearby
TVs and VCRs. To minimize or prevent such
interference, the base of the cordless phone
should not be placed near or on top of a TV
or VCR.
Lightning damage is not common. Neverthe-
less, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
Your telephone operates on standard radio
frequencies as allocated by the FCC. Even
though the access protection code prevents
unauthorized use of your phone line, it is
possible for other radio units operating on
similar frequencies within a certain area to
unintentionally intercept your conversations
and/or cause interference. This lack of priva-
cy can occur with any cordless phone.
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment, ba-
sic safety precautions should always be fol-
lowed to reduce the risk of fire, electric shock
and injury to persons, including the following:
THE FCC WANTS YOU TO
KNOW
1. Read and understand all instructions,
2. Follow all warnings and instructions
marked on the product.
The phone complies with the limits for a
Class B digital device as specified in Part 15
of FCC Rules. These limits provide reason-
able protection against radio and TV interfer-
ence in a residential area. However, your
equipment might cause TV or radio interfer-
ence even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures:
3. Do not use liquid cleaners, or aerosol
cleaners. Use a damp cloth for cleaning.
If necessary, use a mild soap.
4. Do not use this product near water, for
example near a bathtub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
• Reorient or relocate the receiving
antenna.
5. Do not place this product on an unstable
cart, stand or table.The product may fall,
causing serious damage to the product.
• Increase the distance between the
equipment and the radio or TV.
6. Do not allow anything to rest on the tele-
phone line cord. Do not locate this prod-
uct where the cord will be abused by
persons walking on it.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
Consult your local RadioShack store if the
problem still exists.
7. Never spill liquid of any kind on the prod-
uct.
3
Read This Before Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
8. To reduce the risk of electric shock, do
not disassemble this product. If servic-
ing is required, take it to a qualified ser-
viceman.
local codes for possible special disposal
instructions.
2. Use only a replacement battery pack of
the required size and type. Use only a
3.6V 600mAh Nickel Metal Hydride (Ni-
MH) battery pack.
9. Disconnect this product from the tele-
phone line and refer to qualified service
personnel under the following condi-
tions.
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
• If liquid has been spilled into the prod-
uct.
• If the product has been exposed to rain
or water.
4. Exercise care in handling the battery
pack in order not to short the battery
with conductors such as rings, brace-
lets, and keys. The battery pack or con-
ductor may overheat and cause burns.
• If the product has been dropped or the
cabinet has been damaged.
• If the product exhibits a distinct change
in performance.
5. Do not attempt to recharge the battery
pack provided with or identified for use
with this product by heating them. The
battery pack may leak corrosive electro-
lyte or may explode.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are cov-
ered by the operating instructions.
Improper adjustment of controls may
result in damage and require extensive
work by a qualified technician to restore
the product to normal operation.
6. Do not attempt to rejuvenate the battery
pack provided with or identified for use
with this product by heating it. The bat-
tery pack may release electrolyte, caus-
ing burns or irritation to eyes or skin.
10. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electrical
shock from lightning.
7. When inserting the battery pack into this
product, the proper placement must be
observed. Reverse insertion of the bat-
tery pack can cause charging, and that
may result in leakage or explosion.
11. Do not use the telephone to report a gas
leak in the vicinity of the leak.
8. Remove the battery pack from this prod-
uct if the product will not be used for a
long period of time (several months or
more) since during this time the battery
pack could leak in the product.
BATTERY SAFETY
INSTRUCTIONS
CAUTION:
TO REDUCE THE RISK OF
9. Discard a dead battery pack as soon as
possible since dead batteries are more
likely to leak in a product.
FIRE OR INJURY, READ AND FOLLOW
THESE INSTRUCTIONS.
1. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
10. Do not store this product, or the battery
pack provided with or identified for use
4
Read This Before Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
with this product, in high temperature
areas.
Batteries should be stabilized at room
temperature prior to use after cold stor-
age.
11. Batteries that are stored in a freezer or
refrigerator for the purpose of extending
shelf life should be protected from con-
densation during storage and defrosting.
SAVE THESE INSTRUCTIONS
ˆ Contents
Features .................................................................................................................................. 6
Installation .............................................................................................................................. 7
Mounting the Phone ............................................................................................................ 7
Connecting, Charging, and Replacing the Battery Pack ..................................................... 7
Setting the Dialing Mode ..................................................................................................... 8
Storing Your Area Code ....................................................................................................... 9
Setting the Ringer Level ...................................................................................................... 9
Using the Belt Clip ............................................................................................................... 9
Operation .............................................................................................................................. 10
A Quick Look at Your Phone ............................................................................................. 10
Adjusting the Handset’s Volume ......................................................................................... 11
Paging ................................................................................................................................ 11
Memory Dialing .................................................................................................................. 11
Storing a Number and Name in Memory ....................................................................... 11
Entering a Pause .......................................................................................................... 12
Reviewing Memory Numbers ........................................................................................ 12
Dialing a Memory Number ............................................................................................ 12
Chain-Dialing Service Numbers .................................................................................... 12
Testing Stored Emergency Numbers ............................................................................ 12
Moving Out of Range ........................................................................................................ 13
Using a Headset ................................................................................................................ 13
Caller ID Operation .............................................................................................................. 13
Important Caller ID Information ......................................................................................... 13
Reviewing Caller ID Messages ......................................................................................... 13
Caller ID Messages ....................................................................................................... 14
Adding/Deleting the Area Code ......................................................................................... 14
Dialing Numbers from a Caller ID Record ......................................................................... 14
Storing a Caller ID Record in Memory ............................................................................... 14
Deleting Caller ID Records ................................................................................................ 14
Troubleshooting ................................................................................................................... 15
Care ................................................................................................................................... 16
5
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ Features
Headset Jack
Your RadioShack 2.4 GHz Digital Spread
Spectrum Cordless Telephone uses ad-
vanced technology to give you superior au-
dio quality and extended range. The phone’s
Caller ID unit records each caller’s telephone
number (and name, if available in your area)
and the date and time of the call, as provided
by your local phone company to Caller ID
service subscribers. If you subscribe to Call
Waiting with Caller ID, the phone can show
you the incoming caller information, even
when you are already talking on the phone.
— lets you connect an option-
al headset (available from your local
RadioShack store) for handsfree conve-
nience.
Hearing-Aid Compatibility
the phone with hearing aids that have a T
(telephone) switch.
— lets you use
Tone/Pulse Dialing
phone with either type of service.
— lets you use your
3-Line Backlit Display
— lets you view an
entire Caller ID record on one screen even in
the darker environment.
Your phone also has these features:
2.4 GHz Operation
and less interference than many other cord-
less phones.
— provides longer range
Volume Control
volume you hear through the handset.
— lets you adjust the
Adjustable Ringer
tween two volume levels or turn the ringer
off.
— lets you choose be-
Spread Spectrum Technology
— spreads
the signal across several frequencies, pro-
viding additional security for your phone con-
versations.
Belt Clip
— lets you carry the phone on your
belt for easy portability.
40 Channels
— automatically selects a clear
channel when you make or answer a call.
10-Number Speed Dialing
— lets you store
up to 10 numbers in memory for easy dialing.
Caller ID Memory
— stores up to 40 Caller
ID records.
Out-of-Range Signal
— the handset lets
you know when you move out of the base’s
operating range.
Ample Talk and Standby Time
— the sup-
plied battery pack (when fully charged) pro-
vides about 4 hours of talk time or 7 days of
standby time.
Compact Design
— small and easy to hold
in your palm.
6
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ Installation
date the wiring for you. You must use com-
patible modular jacks that are compliant with
Part 68 of FCC Rules.
MOUNTING THE PHONE
Select a flat surface that is:
• near an AC outlet
Note:
The USOC number of the jack to be
installed is RJ11C (or RJ11W for a wall plate
jack).
• near a telephone line jack
• out of the way of normal activities
Follow these steps to set up your phone.
1. Plug one end of the supplied modular
• away from electrical machinery, electri-
cal appliances, metal walls or filing cabi-
nets, wireless intercoms, alarms, and
room monitors
TEL
cord into the
base.
jack on the back of the
2. Insert the supplied AC adapter’s barrel
• away from other cordless phones
DC 9V 300 mA
plug into the
back of the base.
jack on the
The base’s location affects the handset’s
range. If you have a choice of several loca-
tions, try each to see which provides the best
performance.
3. Plug the modular cord’s other end into
the phone jack.
4. Route the adapter cord through the
strain relief slot on the base then plug
the adapter into a standard AC outlet.
Cautions:
You must use a Class 2 power
source that supplies 9V DC
and delivers at least 300 mA.
Its center tip must be set to positive and
5. Lift the base’s antenna to a vertical posi-
tion.
!
DC 9V 300
its plug must fit the phone's
mA
CONNECTING, CHARGING,
AND REPLACING THE
BATTERY PACK
jack. The supplied adapter meets
these specifications. Using an adapter
that does not meet these specifications
could damage the phone or the adapter.
The phone comes with a rechargeable
nickel-metal hydride (Ni-MH) battery pack
in the handset. Before using your phone,
you must connect the battery pack, then
charge it for about 24 hours.
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you dis-
connect it from the phone.
1. Press down and slide off the battery
pack compartment cover.
Your telephone connects directly to a modu-
lar telephone line jack. If your telephone wir-
ing does not have a modular jack, you can
update the wiring yourself using jacks and
adapters (available at your local RadioShack
store), or have the telephone company up-
2. Lift the battery pack out of the compart-
ment.
3. Plug the battery pack's connector into
the socket in the compartment, (the con-
7
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
nector fits only one way), replace the
battery pack, and replace the cover.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an over-
night charge, replace it with a new 3.6-volt,
600 mAh battery pack with a connector that
fits the socket in the battery compartment.
You can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack and charge it for about
24 hours.
To charge the battery pack, place the hand-
set on the base. The CHARGE indicator on
the base lights and JejWb0&& appears.
Recharge the battery pack when Bemý8Wjj[ho
flashes on the display.
Notes:
Warning:
Dispose of the old battery pack
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 4
for additional information on proper battery
handling).
TALK
hear a beep when you press
.
Return the handset to the base for about
5 seconds to reset the security access-
protection code.
SETTING THE DIALING
MODE
• If the handset or the base loses power,
the security access-protection code
might be lost. To reset the code, return
the handset to the base for about 5 sec-
onds.
PULSE-TONE
To set the dialing mode, set
on
the back of the base for the type of service
you have. If you are not sure which type you
have, do this test after you charge the hand-
set’s battery pack.
• Using a pencil eraser, clean the charg-
ing contacts on the handset and base
about once a month.
PULSE-TONE
TONE
.
1. Set
to
TALK
2. Lift the handset, press
for a dial tone.
, and listen
• If the battery pack becomes weak during
a call, the handset beeps every 3 sec-
onds and Bemý8Wjj[ho flashes.
0
3. Press any number other than .
Note:
If your telephone system requires
• About once a month, fully discharge the
battery by keeping the handset off the
base until Bemý 8Wjj[ho flashes. Other-
wise, the battery pack loses its ability to
fully recharge.
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access code
number either.
If the dial tone stops, you have touch-
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
PULSE-TONE
tone service. Leave
set to
TONE
.
If the dial tone continues, you have
PULSE-TONE
pulse service. Set
to
• If you are not going to use your phone
for an extended period of time, discon-
nect the battery pack. This increases the
battery pack's usable life.
PULSE
.
TALK
4. Press
or place the handset on the
base to hang up.
8
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
STORING YOUR AREA
CODE
USING THE BELT CLIP
To attach the belt clip, align the clip with the
slots on the sides of the handset, then snap it
into place.
You can store your local area code in the
phone’s Caller ID record so it does not show
the area code if the received call is from your
local area.
To remove the belt clip, use a flat object such
as a table knife to pry the belt clip off the
phone.
Note:
If your calling area requires 10-digit di-
aling including area code, do not enter the
area code but leave this option blank.
Follow these steps to store your area code.
MUTE/PGM
1. Lift the handset and press
.
7H;7ý9E:; appears.
2. Enter your three-digit area code.
MUTE/PGM
3. Press
twice to exit.
SETTING THE RINGER
LEVEL
You can select high or low ringer volume, or
turn the ringer off.
MUTE/PGM
1. Lift the handset and press
twice. H?D=ýB;L;B appears with the cursor
pointing to the current setting.
/ /TONE
#/
or 7 to move the
2. Press 6 ∗
cursor to the desired setting (>?, BE, or
E<<).
MUTE/PGM
3. Press
.
Note:
When you select E<<, H_d][hý E\\
appears and the phone beeps. You can
still make or receive a call. When you
have an incoming call, the phone con-
nected to the same line rings, and H_d]#
_d] appears (then Caller ID information,
if you subscribe to the service).
9
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ Operation
A QUICK LOOK AT YOUR PHONE
MUTE/PGM — Press to talk to
someone in the room while using
the phone without the person on
the other end of the phone line
hearing your conversation.
appears on the display.
Press again to resume your
phone conversation.
CKJ;
TALK — To make a call, lift the hand-
set and press TALK. appears,
J7BA
and the IN USE/PAGE indicator on the
base lights. Enter the number. The
number appears as you dial, then (after
a few seconds) the call’s elapsed time
appears.
You can also enter the number before
you press TALK. If you make a mis-
take, repeatedly press DELETE until
the incorrect entry is erased. Then en-
ter the correct number. Press TALK to
dial the number. The IN USE/PAGE in-
dicator on the base lights. The number
you entered and the call’s elapsed time
appear.
REDIAL/PAUSE — You
can quickly dial the last
number you dialed. Lift the
handset and press TALK
then REDIAL/PAUSE. The
phone dials the number.
Notes:
When you receive a call,
pears. To answer, lift the handset from
ap-
H_d]_d]
•
•
•
You
can
press
REDIAL/PAUSE first
then press TALK to
dial the number in
redial memory.
Redial memory holds
up to 32 digits, for
redialing
tance or local num-
bers.
the base and press TALK.
pears.
ap-
J7BA
To end a call, press TALK or place the
handset on the base.
long-dis-
Redial memory also
holds pause entries.
FLASH — Performs the electronic
equivalent of a switchhook operation
for special services, such as Call Wait-
ing.
For example, if you have Call Waiting,
press FLASH to answer an incoming
call without disconnecting the current
call. Press FLASH again to return to
the first call.
Note: If you do not have any special
phone services, pressing FLASH
might disconnect the current call.
/ /TONE — Some special servic-
6 ∗
es, such as bank-by-phone, require
tone signals. If you have pulse ser-
vice, you can still use these special
tone services by following these
steps.
Be sure PULSE-TONE is set to
PULSE.
Dial the service’s main number.
When the service answers, press
/ /TONE. Any additional num-
6 ∗
bers you dial are sent as tone signals.
The phone automatically resets to the
pulse mode the next time you make or
receive a call.
10
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow these steps to store a number and
name in memory.
ADJUSTING THE
HANDSET’S VOLUME
1. Lift the handset.
To adjust the handset’s volume during a call,
press 8 or 9 on the handset until you
reach the desired volume level. The number
and a bar graph of the volume level appear.
MEM
2. Press
. C;CEHO appears.
0 9
3. Press a number ( – ) to choose a two-
digit memory location. ;cfjo (or the cur-
rent memory contents if a number is
already stored) appears.
The volume level setting is maintained even
after you hang up the phone.
Note:
When you press 8 while the volume is
MEM
4. Press
. ;DJ;HýD7C; appears. If you
at 4 or 9 while the volume is set at 1, the
handset beeps three times and the setting
does not change.
do not want to enter a name, skip to
Step 6.
5. To enter a name, use the number keys.
PAGING
Refer to the letters on the number keys
to select the desired letter. Press the key
once for the first letter in upper case,
press twice for the second letter in upper
case, and so on. To enter the lower case
letter, press four times (or five times) to
display the first letter in lower case, five
or six times for the second letter, and so
on.
To send a page from the base to the handset
or to locate the handset, when the phone is
not in use, press
USE/PAGE indicator blinks and the handset
beeps for 15 seconds. Press any key or
place the handset on the base to stop the
page sooner.
PAGE
on the base. The IN
Note:
The phone rings when a call comes in
while you are using the page feature.
5
For example, to enter John: press
once; upper case @ appears. Then press
6
4
six times; lower case e appears. Press
five times; lower case ^ appears.
MEMORY DIALING
6
You can store up to 10 phone numbers and
names in memory, then dial a stored number
by entering its memory location number.
Finally, press five times; lower case d
appears.
To enter two letters from the same key in
#/
Each number can be up to 20 digits, and
each name can be up to 12 characters.
a row, press 7 to move the cursor to
the next position. For example to enter
2
#/
AB, press ; 7 appears. Press 7to
move the cursor to the next position,
Storing a Number and Name in
Memory
2
then press twice so 8 appears.
#/
To enter a space, press 7 twice with-
If you receive a call or someone pages the
handset during memory entry, the phone ex-
its the storing process.
out entering any character.
To enter a number, repeatedly press the
corresponding number key until the
number appears.
Important:
The phone exits the storing pro-
cess if you wait more than 20 seconds be-
tween each keypress.
11
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
0
To enter a special character, use . Each
Reviewing Memory Numbers
0
time you press , the following charac-
To review your memory numbers, press
ters appear in this order:
MEM
. C;CEHO appears. Choose a memory
*
ç ¶ ) âýá (space) U &ý
location (0–9) by pressing a number or by re-
peatedly pressing 8 or 9. The selected
memory location number appears with the
number and the name (if stored).
/ /TONE
If you make a mistake, use 6 ∗
to move the cursor over the error, then
DELETE
press
to delete the wrong char-
acter and then enter the correct charac-
ter.
MEM
To exit the memory number list, press
three times.
MEM
6. Press
. ;DJ;HýDKC8;H appears.
Dialing a Memory Number
7. Enter the phone number and any tone or
pause entries (see “A Quick Look at
Your Phone” on Page 10 and “Entering
a Pause”).
To dial a number stored in memory, lift the
MEM
handset and press
. C;CEHO appears.
Choose a memory location (0–9) by pressing
a number or by repeatedly pressing 8 or
TALK
9. Press
.
MEM
8. Press
. The phone beeps and the
name and number are stored.
You can also dial a memory number after
TALK
MEM
, then enter a
pressing
. Press
To replace a stored number, store a new one
memory location number.
MEM
in its place. To delete a number, press
,
then choose a memory location (0–9) by
pressing a number or by repeatedly pressing
Chain-Dialing Service Numbers
DELETE
8 or 9. Press
. ;hWi[5 appears.
For quick recall of numbers for special ser-
vices (such as bank-by-phone), store each
group of numbers in its own memory loca-
tion. Dial the service’s main number first.
Then, at the appropriate place in the call,
Press :;B;J; again. The display changes to
;cfjo.
To delete all numbers in memory, recall any
DELETE
location, then hold down
until ;hWi[
DELETE
MEM
and enter the number for the lo-
7bb5 appears. Press
again.
press
cation where the additional information is
stored.
Entering a Pause
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an out-
side number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to con-
nect. To enter a 2-second pause when you
Testing Stored Emergency Num-
bers
If you store an emergency service’s number
(police department, fire department, ambu-
lance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
REDIAL/PAUSE
are storing a number, press
.
F appears for pause entry. You can add more
pause entries for a longer pause.
12
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
When you finish using the headset, discon-
nect it from the handset.
MOVING OUT OF RANGE
If you have the handset out of the base's
range while a call is in progress, the handset
beeps and EKJýE<ýH7D=; appears. Return to
the base’s range within 30 seconds, then you
can resume your phone conversation.
Notes:
• Connecting a headset disconnects the
handset’s earpiece and microphone.
MUTE/PGM
• 8/9 and
on the handset
USING A HEADSET
also controls the headset’s volume.
You can make or answer calls with hands-
free convenience using an optional headset
that has a /32-inch (2.5-mm) plug. Contact
your local RadioShack store for a suitable
headset.
• If you place the handset on the base to
recharge it while the headset is con-
nected, be sure the handset seats prop-
erly.
3
• With a headset connected, you can
make or answer calls as usual using the
keys on the handset.
To connect the headset, insert the headset’s
plug into the jack.
ˆ Caller ID Operation
If you subscribe to Caller ID service from
your phone company, the phone company
sends information about the call, as well as
the time and date, between the first and sec-
ond rings of every call you receive.
IMPORTANT CALLER ID
INFORMATION
To use the phone's Caller ID and Call Wait-
ing with Caller ID features, you must be in an
area where those services are available and
you must subscribe to those services
through your local phone company. Where
Caller ID is offered, one or more options are
generally available:
The phone displays this information after the
second ring, and it stores up to 40 Caller ID
records for later review. It also shows if caller
information is unavailable or if the name and
number were blocked by the caller (see
“Caller ID Messages”).
• caller’s name only
If you subscribe to Call Waiting with Caller
ID, you will hear a tone through the handset
when a call comes in, then the Caller ID
record appears. If you want to answer the in-
• caller’s number only
• caller’s name and number
FLASH
coming call, press
. To resume the
REVIEWING CALLER ID
MESSAGES
FLASH
previous phone conversation, press
again.
To review the Caller ID records, lift the hand-
set and press either 9 (to view from the
newest record) or 8#(to view from the old-
est record). Repeatedly press 9 or 8 to
scroll through the Caller ID records.When
If the phone’s Caller ID memory becomes
full, any new call replaces the oldest call’s
record.
13
Caller ID Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
you scroll past the last record, ;
d
Z
ý
e
\
ý
B
_
i
j
ap-
different, the record shows the area code.
However, you can add or delete the area
code on the display. When the record is on
pears, then the first record. When you scroll
past the first record, ;dZýe\ýB_ij appears, then
the last record.
3
the display, press to add or delete the area
3
code. Pressing again deletes or adds the
area code.
The top line of each record shows the time,
date, and the number of calls from that num-
ber. The second line shows the caller’s
phone number, and the third line shows the
caller’s name.
DIALING NUMBERS FROM A
CALLER ID RECORD
To dial a local number stored in a Caller ID
To exit the Caller ID record display, press
TALK
record, recall the record, then press
. If
TALK
twice, or return the handset to the
1
it is a long distance call, press (' appears
base.
before the displayed number) before you
TALK
press
. If you want to add or delete the
Caller ID Messages
3
TALK
.
area code, press before you press
Note:
If a Caller ID record does not contain a
Display
Description
phone number (if it was blocked by the caller,
for example), you cannot dial from that
record.
Shows the number of new
Caller ID records (records
you have not reviewed)
and the total number of
records.
If you have set the
ringer off, only the number
of new records appears.
JejWb0NN
D[m0ýNN
STORING A CALLER ID
RECORD IN MEMORY
Note:
1. Press 8 or 9 to recall the record you
want to store.
Fh_lWj[ýDWc[ýor
Fh_lWj[ýDe$
The caller has blocked the
Caller ID information.
If you want to add or delete the area
KdademdýDWc[ýor The caller is not within a
KdademdýDe$
3
code, press .
Caller ID service area.
MEM
2. Press
. C;CEHO appears.
Appears if there was an
error during the transmis-
sion of Caller ID informa-
tion. Occasional errors are
normal. If the phone fre-
quently displays :WjWý
;hheh, contact your local
telephone company or
RadioShack store.
:WjWý;hheh
3. Choose a memory location (0–9) by
pressing a number or by repeatedly
pressing 8 or 9.
;cfjo appears if the location does not
contain a number. The current contents
of the location appear if it does contain a
number. Check to be sure that you want
to overwrite the current contents.
ADDING/DELETING THE
AREA CODE
MEM
4. Press
. The phone beeps to confirm
that it stored the number, then the total
number of Caller ID records appears.
When the area code of the received call is
the same as the one you stored (see “Storing
Your Area Code” on Page 9), the caller ID
record does not show the area code. If it is
14
Caller ID Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
again. The phone beeps once indicating that
the record was deleted.
DELETING CALLER ID
RECORDS
To delete all Caller ID records, while a Caller
To delete a single Caller ID record, press 8
or 9 to recall the record you want to delete.
DE-
ID’s data is on the display, hold down
LETE
for three seconds. ;hWi[ý7bb5 appears.
DELETE
Press
. ;hWi[5 appears, prompting
DELETE
Press
again. The phone beeps once
DELETE
you to confirm the deletion. Press
and JejWb0&& appears indicating that all Caller
ID records were deleted.
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem
Suggestion
The phone does not work or works poorly.
Be sure the base’s phone line cord and AC adapter
are correctly and securely connected.
Be sure the battery pack in the handset is connected
and charged.
The handset stops working or works poorly
during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical position.
Be sure the handset’s battery pack is charged. (If the
battery pack power is too low, the handset cannot
displayýBemý8Wjj[ho.)
Low volume or unusual sounds.
Dropout or mute.
Someone has picked up another phone on the same
line. Hang up the other phone.
Move to another location or turn off the source of
interference.
Hang up and redial the number.
The phone cannot be operated at a useful
distance from the base because the signal is
weak or noisy (handset’s range has
decreased).
Be sure neither the handset’s nor base’s antenna is
touching a metal surface.
Return the handset to the base and recharge the
battery pack.
The handset’s battery pack does not charge.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery.
The handset does not ring or receive a page.
Lift the base’s antenna to a vertical position.
Be sure the battery pack in the handset is connected
and charged.
Move the base away from other electrical devices.
15
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Suggestion
You have an incoming call, but do not receive
any Caller ID information.
Let the phone ring twice before you answer so the
phone has time to record the Caller ID information.
Check that the phone is correctly and securely con-
nected.
Check with your phone company to verify that your
Caller ID service is active.
If you still have problems, disconnect the phone. If other phones on the same line work proper-
ly, the fault is in this phone or its installation. If you cannot find the problem, take the phone to
your local RadioShack store for assistance.
CARE
Keep the phone dry; if it gets wet, wipe it dry immediately. Use and store the phone only in nor-
mal temperature environments. Handle the phone carefully; do not drop it. Keep the phone
away from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new.
Modifying or tampering with the phone’s internal components can cause a malfunction and
might invalidate its warranty and void your FCC authorization to operate it. If your phone is not
performing as it should, take it to your local RadioShack store for assistance. If the trouble is
affecting the telephone lines, the phone company can ask you to disconnect your phone until
you have resolved the problem.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the
date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR
ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR
PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY
DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any
RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts
and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and prod-
ucts on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for
repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage,
failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) trans-
portation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-3519
RadioShack Corporation
05A01
Fort Worth, Texas 76102
Printed in Korea
Download from Www.Somanuals.com. All Manuals Search And Download.
|