43-469.fm Page 1 Tuesday, January 19, 1999 9:48 AM
Cat. No. 43-469
OWNER’S MANUAL
Please read before using this equipment.
ET-469
Two-Line Speakerphone with
Line Status Indicators
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 3 Tuesday, January 19, 1999 9:48 AM
This telephone has been tested and
found to comply with all applicable UL
and FCC standards.
READ THIS BEFORE
INSTALLATION
This telephone conforms to federal regu-
lations, and you can connect it to most
telephone lines. However, each device
that you connect to the phone line draws
power from the phone line. We refer to
this power draw as the device’s ringer
equivalence number, or REN. The REN
is on the bottom of the phone.
We recommend you record your
phone’s serial number here. The num-
ber is on the bottom of the phone.
Serial Number __________________
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five (or
three in rural areas), your phones might
not ring. If ringer operation is impaired,
remove a device from the line.
To reduce the risk of fire or
shock hazard, do not expose this product to
rain or moisture.
WARNING:
CAUTION
!
RISK OF ELECTRIC SHOCK. DO
NOT OPEN.
FCC STATEMENT
: TO REDUCE THE RISK
CAUTION
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER OR BACK. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
PERSONNEL.
This telephone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number
and the REN to your phone company.
These numbers are on the bottom of the
phone.
This symbol is intended to alert you to
the presence of uninsulated danger-
ous voltage within the product’s enclo-
sure that might be of sufficient
magnitude to constitute a risk of elec-
tric shock. Do not open the product’s
case.
Note: You must not connect the tele-
phone to:
• coin-operated systems
• party-line systems
This symbol is intended to inform you
that important operating and mainte-
nance instructions are included in the
literature accompanying this product.
• most electronic key phone systems
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 4 Tuesday, January 19, 1999 9:48 AM
CONTENTS
Installation .............................................................................................................. 5
Choosing a Location .......................................................................................... 5
Mounting the Phone .......................................................................................... 5
On a Desktop .............................................................................................. 5
On a Wall-Plate ........................................................................................... 7
On a Wall .................................................................................................... 8
Connecting the Handset Cord ........................................................................... 9
Preparation ........................................................................................................... 10
Line Status Indicators ...................................................................................... 10
Adjusting the Line Status Indicators .......................................................... 10
Disabling Line 2 ................................................................................................ 11
Setting the Dialing Mode .................................................................................. 11
Setting the Ringer ............................................................................................. 11
Confirming the Line Numbers ........................................................................... 11
Basic Operation ................................................................................................... 12
Using the Speakerphone ................................................................................. 12
Switching Between the Handset and the Speakerphone .......................... 13
Adjusting the Volume ....................................................................................... 13
Using HOLD ..................................................................................................... 13
Using PRIVACY ................................................................................................ 14
Using FLASH .................................................................................................... 14
Using REDIAL .................................................................................................. 14
Conference Calling .......................................................................................... 14
Using Tone Services on a Pulse Line .............................................................. 15
Special Features .................................................................................................. 16
Using Memory Dialing ..................................................................................... 16
Storing a Number in Memory .................................................................... 16
Storing a Pause in Memory ....................................................................... 17
Dialing a Stored Number ........................................................................... 17
Chain Dialing Service Numbers ................................................................ 17
Testing Stored Emergency Numbers ........................................................ 17
Using the Phone Number Index Card ....................................................... 18
Connecting an Optional Headset ..................................................................... 18
Troubleshooting ................................................................................................... 19
Care and Maintenance ......................................................................................... 20
The FCC Wants You to Know .......................................................................... 21
Lightning .......................................................................................................... 21
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 5 Tuesday, January 19, 1999 9:48 AM
INSTALLATION
CHOOSING A LOCATION
MOUNTING THE PHONE
You can use your telephone as a desk
phone, mount it on a standard wall plate,
or mount it directly on a wall. Select a lo-
cation that is near the telephone line
jack(s) and an easily accessible AC out-
let
On a Desktop
1. Remove the mounting bracket by
holding in the tab on the right side of
the bracket and gently pulling the
bracket away from the base.
To take full advantage of many of the
ET-469’s features (like conference call-
ing) you must have two telephone lines
with separate phone numbers. If you
have only one phone line, you can order
a second line from your local phone
company.
2. If you have a single two-line phone
jack, plug one end of the supplied
two-line long modular cord into L1 or
L1/L2 on the back of the phone’s
base.
You can use a two-line jack (RJ14C or
RJ14W for a wall plate) that contains
both lines, or you can use a separate
single-line jack (RJ11C) for each line.
Notes:
L1/L2
• The line that connects the phone
jack to the telephone company wir-
ing must be twisted-pair cable. Oth-
erwise, you might experience
interference (crosstalk) between the
two phone lines.
Note: If you connect the phone to a
two-line phone jack with a two-line
cord, do not connect another modu-
lar cord to the L2 jack. Otherwise,
the phone will not operate properly.
• Your telephone connects directly to
a modular telephone line jack. If
your telephone wiring does not have
a modular jack, you can update the
wiring yourself using jacks and
adapters available at your local
RadioShack store, or have the tele-
phone company update the wiring
for you.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 6 Tuesday, January 19, 1999 9:48 AM
If you have two separate one-line
modular jacks, plug one end of the
supplied two-line long modular cord
into L1 or L1/L2 and plug the sup-
plied one-line long modular cord into
L2.
4. Route the adapter’s cord through
the strain relief slot on the back of
the phone.
Strain Relief Slot
5. Insert the bracket’s two small tabs
into the matching slots at the upper
left on the bottom of the phone, and
snap the large tab of the bracket into
the large slot at the upper right.
3. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
the back of the phone.
DC 9V
6. Connect the other end(s) of the
phone cord(s) to the phone line
jack(s).
Caution: You must use a
Class 2 power source that
!
supplies 9 volts DC and
delivers at least 150 mA. Its center
tip must be set to negative and its
plug must fit the TAD-469's
DC 9V
jack. The supplied adapter meets
these specifications. Using an
adapter that does not meet these
specifications could damage the
TAD-469 or the adapter.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 7 Tuesday, January 19, 1999 9:48 AM
7. Plug the AC adapter into a standard
AC outlet.
3. If the wall plate has a single two-line
phone jack, plug one end of the sup-
plied two-line short modular cord
into L1 or L1/L2 on the back of the
phone's base.
If the wall plate has a single one-line
phone jack, and there is another
telephone jack close by, plug one
end of the supplied two-line short
phone cord into L1 or L1/L2, and
plug the supplied one-line long
phone cord into L2.
On a Wall-Plate
1. Remove the bracket by pressing
and holding in the tab on the right
side of the bracket, then gently pull-
ing the bracket away from the base.
2. Insert the bracket’s two small tabs
into the matching slots at the lower
right on the bottom of the phone,
and snap the large tab into the large
slot at the lower left.
4. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
the back of the phone.
DC 9V
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 8 Tuesday, January 19, 1999 9:48 AM
5. Plug the other end of the two-line
short modular cord into the wall
plate jack. If you attached a long
modular cord, plug it into the wall
jack. Align the wall plate studs with
the phone's keyhole slots and slide
the phone downward to secure it.
and snap the large tab into the large
slot at the lower left.
6. Plug the adapter into a standard AC
outlet.
4. If you have a single two-line phone
jack, plug one end of the supplied
two-line short modular cord into L1
or L1/L2 on the back of the phone's
base.
On a Wall
To mount your phone on a wall, you
need two screws (not supplied) with
heads that fit into the keyhole slots on
the bottom of the phone.
3/16
L1/L2
15
16
1. Drill two holes 3 /
inches
(100
mm)
apart. Then, thread a
screw into each hole,
315/16
letting
the
heads
3
16
extend about / inch
(5 mm) from the wall.
If you have a single one-line phone
jack, and there is another modular
telephone line jack close by, plug
one end of the supplied two-line
short phone cord into L1 or L1/L2,
and plug the supplied one-line long
phone cord into L2.
2. Remove the bracket by holding in
the tab on the right side of the
bracket and gently pulling the
bracket away from the base.
3. Insert the bracket’s two small tabs
into the matching slots at the lower
right on the bottom of the phone,
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 9 Tuesday, January 19, 1999 9:48 AM
5. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
the back of the phone.
DC 9V
6. Plug the other end of the two-line
short modular cord into one of the
wall jacks. If you attached a long
modular cord, plug it into the other
wall jack. Align the screws on the
wall with the phone’s keyhole slots
and slide the phone downward to
secure it.
7. Plug the adapter into a standard AC
outlet
CONNECTING THE
HANDSET CORD
Plug the supplied coiled handset cord
into the jacks on the handset and the
left side of the phone.
Note: Your local RadioShack store sells
a variety of longer coiled handset cords,
which are especially useful when you
mount the phone on the wall.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 10 Tuesday, January 19, 1999 9:48 AM
PREPARATION
1. Press LINE 1 then lift the handset.
The LINE 1 indicator should light
steadily.
LINE STATUS
INDICATORS
The Line Status Indicators show you
which line is in use or on hold. If a line is
on hold, the indicator light flashes. If a
line is in use, the indicator lights.
2. Press HOLD. The indicator should
flash slowly.
3. If the indicator worked correctly, it
does not need adjustment. Other-
wise, proceed to Step 4.
4. Slide the phone’s name and number
index card and plastic cover out of
its slot and remove it. Locate the L1
control.
Indicator is:
Line is:
Off
Not in use
In use
On Steadily
Flashing rapidly
Flashing slowly
Ringing
On hold
5. Press HOLD and insert the supplied
flat-blade screwdriver into the indi-
cator control slot and turn in either
direction until the line indicator
flashes slowly.
Adjusting the Line Status
Indicators
6. Press LINE 1. If the indicator flashes
slowly, turn the L1 control until the
indicator lights steadily.
Each line status indicator is preset to
work correctly with most telephone lines.
However, if an indicator does not light
when its line is in use, you may need to
adjust the indicator to ensure correct op-
eration.
7. Press HOLD again and repeat Steps
4 and 5 until the indicator works cor-
rectly with the line on and off hold.
Repeat these steps to adjust L2.
Follow these steps to test and adjust the
Line Status Indicators.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 11 Tuesday, January 19, 1999 9:48 AM
DISABLING LINE 2
Should you ever need to disable Line 2,
leave the handset in the cradle and
.
press HOLD, LINE 2, then
To enable the Line 2 indicator, leave the
handset in the cradle and press HOLD,
LINE 2, then #.
If you do not want a line’s ringer to
sound, set RINGER OFF/LO/HI for that
line to OFF. The line indicator will light
when a call comes in. You can still re-
ceive and make calls on that line.
SETTING THE DIALING
MODE
Set T/P (Tone/Pulse) on the back of the
phone for the type of service you have. If
you are not sure which type you have,
do this test.
CONFIRMING THE LINE
NUMBERS
1. Press LINE 1.
2. Set T/P to T.
Follow these steps to determine which
phone number is connected to which
line.
3. Press any number other than 0.
If the dial tone stops, you have
touch tone service. Leave T/P set to
1. Press LINE 1 then lift the handset.
T.
2. Dial one of your phone numbers. If
the Line 2 indicator flashes, the
number is connected to Line 2. If
you hear a busy signal, the number
is connected to Line 1.
If the tone continues, you have
pulse service. Set T/P to P.
SETTING THE RINGER
After you confirm the phone number for
each line, write each number on the
name and number directory located
above the L1 and L2 buttons.
The lines on your phone ring with differ-
ent tones when you receive a call. You
can set the phone lines to ring at the
same volume, at different volumes, or
not at all.
To set each ringer’s volume, set RINGER
OFF/LO/HI for that line to the desired po-
sition.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 12 Tuesday, January 19, 1999 9:48 AM
BASIC OPERATION
To make a call, pick up the handset and
select a line by pressing LINE 1 or LINE
2. When you hear the dial tone, dial the
number.
USING THE
SPEAKERPHONE
To make or answer a call using the
speakerphone, press HEADSET/SPEAK-
ER. The SPEAKER indicator lights and
the phone automatically selects a free
line or the line that is ringing.To make a
call or answer on the other line, press
the line’s button (LINE 1 or LINE 2).
Notes:
• The phone automatically selects the
free line if you do not press LINE 1 or
LINE 2.
• If you do not select a line before
picking up the handset, the free line
activates.
To end a speakerphone call, press
HEADSET/SPEAKER. The SPEAKER in-
dicator turns off.
When you receive a call on a line, the in-
dicator for that line flashes and the
phone rings (if RINGER is set to LO or
HI). To answer the call, press the ringing
line’s button (LINE 1 or LINE 2) and pick
up the handset.
Notes:
• If background noise interferes with
the speakerphone’s operation, you
can press PRIVACY to turn off the
base’s microphone while the other
party is speaking (see “Using Pri-
vacy” on Page 14).
To help you tell which line is ringing,
each line has a distinctive ring tone. Line
1has a higher tone than Line 2.
• You cannot use the speakerphone
with a headset connected to the
phone (see “Connecting an Optional
Headset” on Page 18).
Note: Line 2 does not operate during a
power failure.
• You cannot use the speakerphone
during a power failure.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 13 Tuesday, January 19, 1999 9:48 AM
Switching Between the
Handset and the Speakerphone
USING HOLD
To place a call on hold, press HOLD.
You can then hang up the handset or
use the other phone line (to answer an-
other call, for example) without discon-
necting the current call.
To switch from the handset to the
speakerphone at any time during a call,
press HEADSET/SPEAKER so its red in-
dicator lights, then resume the conver-
sation.
To pick up a line that is on hold, press
that line’s button (Line 1 or Line 2).
To switch from the speakerphone to the
handset, just lift the handset and resume
your conversation. The SPEAKER indi-
cator turns off.
Notes:
• You can put a call on hold at one
extension and pick up the call at
another extension.
ADJUSTING THE VOLUME
• You can alternate between two lines
by pressing HOLD to put your cur-
rent line on hold, then pressing the
button for the line you want to pick
up.
To increase or decrease the volume
when using the speakerphone, hand-
set, or connected headset, press VOL-
UME
or
.
• If you press the other line’s button
without first pressing HOLD, the first
call disconnects.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 14 Tuesday, January 19, 1999 9:48 AM
USING PRIVACY
USING REDIAL
If you do not want the person on the oth-
er end of the phone line to hear your
conversation with someone else at your
location, press PRIVACY. The PRIVACY
indicator lights and the microphone
turns off, but you can still hear the call-
ing party. Press PRIVACY again to re-
sume your conversation.
You can quickly redial the last number
dialed from the selected line.
To use redial with the handset, lift the
handset then press REDIAL when you
hear the dial tone.
To use redial with the speakerphone,
press HEADSET/SPEAKER then REDIAL.
Notes:
• The redial memory holds up to 31
digits, so you can redial long-dis-
tance as well as local phone num-
bers.
USING FLASH
Use FLASH to perform the switchhook
operation for special phone services,
such as Call Waiting.
• When you redial a phone number
that includes a FLASH entry, the
phone only redials the numbers you
pressed before FLASH.
CONFERENCE CALLING
For example, if you have Call Waiting,
press FLASH to take an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
Conference calling lets you conduct a 3-
way conversation, joining Line 1 and
Line 2 into one phone call. To place a
conference call, follow these steps.
1. Place a call to one party.
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 15 Tuesday, January 19, 1999 9:48 AM
2. Press HOLD to put the first call on
return to the three-way conversa-
hold.
tion, press CONF.
5. To end the conference call with both
lines, hang up the handset.
To disconnect one line and continue
talking on the other, press either
LINE 1 or LINE 2.
USING TONE SERVICES
ON A PULSE LINE
3. Press either LINE 1 or LINE 2 for the
line not in use, then place a call to
another party.
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by following
these steps.
1. Set T/P (Tone/Pause) at the back of
the base to P.
4. After the second party answers,
press CONF. This connects all three
parties.
2. Dial the service’s main number.
3. When the service answers, press
. Any additional numbers you dial
are sent as tone signals.
4. After you complete the call, hang
up. The phone automatically resets
to the pulse mode.
Note: To talk on only one line with-
out disconnecting the other line,
press HOLD. Both lines’ red indica-
tors flash. Then, press the button for
the line you want to talk on. To
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 16 Tuesday, January 19, 1999 9:48 AM
SPECIAL FEATURES
Notes:
USING MEMORY DIALING
• Each pause entry counts as one
memory digit.
You can store up to 20 numbers in the
speakerphone’s memory and dial a
stored number at the press of a few but-
tons. Each stored number can be up to
24 digits.
• If you make a mistake while
entering the number, start again
at Step 1.
4. Press SAVE.
Storing a Number in Memory
5. Select the location where you want
to store the number.
Each of the phone's 10 memory loca-
tions can hold up to 2 phone numbers;
one each in an upper and lower memory
location.
• For an upper memory location,
press a memory number button.
Follow these steps to store a number in
memory.
Note: To prevent unauthorized access
to special services, we recommend you
do not store a personal identification
number in memory.
1. Lift the handset from the cradle or
• For a lower memory location,
press LOWER, then a memory
number button.
press HEADSET/SPEAKER.
2. Press SAVE.
3. Enter the phone number you want to
store (up to 24 digits, including any
PAUSE entries). (See “Storing a
Pause in Memory” on Page 17.)
Each time you finish storing or eras-
ing a number in memory, the speak-
erphone beeps to confirm the entry.
Repeat these steps for each number
you want to store.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 17 Tuesday, January 19, 1999 9:48 AM
Notes:
Dialing a Stored Number
• To change a number in memory,
store a new one in its place.
To dial a number stored in memory, lift
the handset or press HEADSET/SPEAK-
ER, then:
• To erase a number from memory, re-
peat all except Step 2, selecting the
location you want to erase in Step 4.
• To dial a number stored in upper
memory, press the desired memory
location number.
Storing a Pause in Memory
• To dial a number stored in lower
memory, press LOWER then the de-
sired memory location number.
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect.
Note: If you select a memory location
number that does not have a phone
number stored in it, press HEADSET/
SPEAKER again then press the correct
memory location number.
To add one or more 2-second pauses to
a phone number you are storing in
memory, press REDIAL at each point
where a pause is needed.
Chain Dialing Service Numbers
You can make a call using more than
one of the two-line speakerphone's
memory locations. This is called chain
dialing. Chain dialing is useful for dial-
ing special services such as alternate
long distance or bank-by-phone.
Testing Stored Emergency
Numbers
Note: Each pause entry counts as one
memory digit in the stored number.
If you store an emergency service’s
number (police and fire departments,
ambulance) and you want to test the
stored number, make the test call dur-
ing the late evening or early morning
hours to avoid peak demand periods.
Also, remain on the line to explain the
reason for your call.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 18 Tuesday, January 19, 1999 9:48 AM
2. Place the headset on your head with
the earpiece over either ear and
adjust the microphone boom until it
is about even with your chin.
Using the Phone Number Index
Card
Slide the phone’s name and number in-
dex card and plastic cover out of its slot
and remove it. Use the phone number
index card on the base to keep track of
numbers stored in the memory loca-
tions or to record important phone num-
bers.
3. Press HEADSET to make or receive
calls.
When you finish the conversation,
press HEADSET to hang up
Note: The headset does not operate
during a power failure.
CONNECTING AN
OPTIONAL HEADSET
Your ET-469 is equipped with a headset
jack on the base. This jack allows you to
connect an optional headset (such as
RadioShack Cat. No. 43-195) so you
can step away from the phone within the
headset cord’s length — perfect for
when you are moving around in the of-
fice or kitchen.
Follow these steps to use a headset:
3
32
1. Insert the headset’s / -inch (2.5
mm) plug into the jack on the right
side of the base.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 19 Tuesday, January 19, 1999 9:48 AM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, these
suggestions might help.
Problem:
Suggestion:
Low volume or unusual sounds.
Someone has picked up another phone on
the same line. Hang up the other phone.
Phone does not work or works Check that the appropriate LINE button is
poorly.
pressed.
Check the T/P (Tone/Pulse) setting.
Check the phone line connection.
Check the AC adapter connection.
The call is too noisy (static or inter- Hang up and redial the number.
ference).
Both red line indicators are lit, but Check that the modular cord is properly con-
there is no dial tone on either line. nected at both ends.
The phone’s line status indicators Adjust the line status indicators.
do not light.
If you still have problems, disconnect the phone. If other phones on the same line(s)
work properly, the fault is in this phone or its installation. If you cannot locate the
problem, take your phone to your local RadioShack store for assistance.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 20 Tuesday, January 19, 1999 9:48 AM
CARE AND MAINTENANCE
Your RadioShack ET-469 Two-Line Speakerphone is an example of superior
design and craftsmanship. The following suggestions will help you care for
your ET-469 so you can enjoy it for years.
Keep the ET-469 dry. If it gets wet, wipe it dry immediately. Liq-
uids might contain minerals that can corrode the electronic cir-
cuits.
Use and store the ET-469 only in normal temperature environ-
ments. Temperature extremes can shorten the life of electronic
devices and distort or melt plastic parts.
Keep the ET-469 away from dust and dirt, which can cause pre-
mature wear of parts.
Handle the ET-469 gently and carefully. Dropping it can damage
circuit boards and cases and can cause the ET-469 to work im-
properly.
Wipe the ET-469 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong de-
tergents to clean the ET-469.
Modifying or tampering with the ET-469’s internal components can cause a
malfunction and might invalidate its warranty and void your FCC authoriza-
tion to operate it. If your ET-469 is not performing as it should, take it to your
local RadioShack store for assistance. If the trouble is affecting the telephone
lines, the phone company can ask you to disconnect your ET-469 until you
have resolved the problem.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 21 Tuesday, January 19, 1999 9:48 AM
THE FCC WANTS YOU TO
KNOW
LIGHTNING
Your telephone has built-in protection
circuits to reduce the risk of damage
from surges in telephone line and power
line current. These protection circuits
meet or exceed the FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your telephone service.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 22 Tuesday, January 19, 1999 9:48 AM
NOTES
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 23 Tuesday, January 19, 1999 9:48 AM
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-469.fm Page 24 Tuesday, January 19, 1999 9:48 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
3/97
We Service What We Sell
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
01A99
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|