Battery Saver
Your universal remote control saves battery power by
automatically turning off if any key is pressed for more
than 60 seconds. This saves your battery life should
your remote get stuck in a place where the keys remain
depressed, such as between sofa cushions.
RCRBB04GR
Step 2: Program your remote
Universal Remote Control
Owner’s Manual
To use this universal remote with your home entertainment
system, first you need to program it to control your devices.
There are four ways you can program the universal remote
to operate your devices. Try them in the order listed here:
Manual del Propietario (parte posterior)
•
•
•
•
The Brand Code Search searches through the codes
FCC Statement:
for select brands of devices.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The Direct Code Entry lets you enter a code from the
accompanying code list for your brand of device.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
The Auto Code Search goes automatically through all
the codes for the device you’re trying to control.
The Manual Code Search lets you manually go
through all the codes for the device you’re trying to
control.
Brand Code Search
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
The Brand Code Search goes through only the codes for one
of the select brands listed in the accompanying code list. If
your brand of device is listed, this search can be very quick
and easy.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
Industry Canada Regulatory Information
This class B digital apparatus complies with Canadian ICES-003
Avis d’Industrie Canada
TIPS: Each device key is associated with a type
of device—the TV is preset to search for TVs,
SAT•CBL•STRM for satellite receivers, cable boxes
or digital TV converters or streaming media players,
DVD•VCR for DVD players, and DVR•AUX for DVRs. To
program a device key for a different type of device, see
the Changing a Key’s Device Type section.
Cet appareil numérique de la classe B est conforme a la nome NMB-
003du Canada
SAVE THIS MANUAL AND THE CODE LISTS!
Remote controls can sometimes lose their programming
when you change the batteries. Make sure you keep the
manual and code lists in a safe place so that you can
reprogram the remote if you need to.
To exit without saving a new code at any point in the
Brand Code Search, press the CLEAR key.
Tip: This remote is already programmed to operate
most RCA-branded TVs, VCRs, DVD players and satellite
receivers. Just press the corresponding key—DVD•VCR
for a DVD player, TV for a television, SAT•CBL•STRM for a
satellite receiver, DVR•AUX for a DVR.
1. Manually turn on the device you
want to control.
Congratulations on your purchase of this 4-device RCA
Universal Remote Control. This remote features a library
of codes with the latest devices of all major brands, with
support for streaming media players as well. The navigation
keys have been redesigned to function seamlessly with the
more sophisticated menu and guide systems found in today’s
home entertainment devices.
2. Find your device’s brand in the
Brand Code list section of the
accompanying code list. Circle
the number for your brand and
keep the list handy.
Step 1: Install your batteries
Your universal remote requires two AAA alkaline batteries
(not included).
To install the batteries:
1. Press and push the
battery compartment
cover to remove it.
3. Press and hold the device key you want to program.
While you’re holding down the device key, use your
other hand to press and hold the remote’s POWER key
at the same time.
2. Insert the batteries,
matching the batteries
to the (+) and (–) marks
inside the battery
compartment.
3. Push the battery cover
back into place.
Battery Precautions:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly
and recycle or dispose of them in accordance with Local
and National Regulations.
4. Wait until the POWER key comes
on and stays on. Then release
both keys.
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Code Search
NOTES
The Auto Code Search goes automatically through all the
codes for the device you’re trying to control. When you find
the one that operates your device, you can stop the search
and store that code.
Throughout the programming of each key, be sure to
keep the remote pointed at the IR sensor of the device
you are currently programming the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don’t work, try
a different code. See the “Testing the Code for Maximum
Functionality” section below for more information.
During the Auto Code Search, the remote ignores
keypresses that aren’t part of the search.
The search times out after two minutes (the POWER key
blinks four times and turns off, and the last programmed
code under that device key is retained).
TIPS: Each device key is associated with a type
of device—the TV is preset to search for TVs,
SAT•CBL•STRM for satellite receivers, cable boxes
or digital TV converters or streaming media players,
DVD•VCR for DVD players, and DVR•AUX for DVRs. To
program a device key for a different type of device, see
the Changing a Key’s Device Type section.
To exit without saving a new code at any point in the
Auto Code Search, press the CLEAR key.
The POWER key blinks four times and turns off when the
remote has gone through all the codes. The remote exits
the Auto Code Search. If your device hasn’t turned off
yet, try a different search method.
1. Manually turn on the device you
want to control.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote.
If some device features don’t work, go to the next step
to try a different code.
2. Press and hold the device key you want to program.
While you’re holding down the device key, use your
other hand to press and hold the remote’s POWER key
at the same time.
2. Repeat the Auto Code Search Method from the
beginning. When your device turns off, do not stop
searching. Instead, with the unit now off, continue to
press the PLAY key every 5 seconds until the unit turns
back on.
3. Once the unit turns back on, press the REVERSE key
on the remote every 2 seconds until your device turns
off again. When your device turns off again, press the
STOP key.
3. Wait until the POWER key comes
on and stays on. Then release
both keys.
4. Test the key’s functionality again by attempting to
control a variety of the device’s functions. If the code
that has been stored controls the majority of the
device’s functions, programming is complete. If the
code stored does not give maximum functionality, try
another code.
4. Keep the remote pointed
directly at the front panel
of the device you want to
control. Press PLAY on the
remote and wait 5 seconds.
The remote is testing a batch
of 10 codes on your device.
Manual Code Search
The Manual Code Search lets you go one-by-one through
all the codes for the device you’re trying to control. When
you find the one that operates your device, you can stop the
search and store that code.
Did your device turn off?
YES: Go to step 5.
NO: Press PLAY again. The remote tests the next batch
of 10 codes.
TIPS: The Manual Code Search method may take a long
time because the remote searches through all of the
codes in its memory one-by-one. If your brand is listed
in the Brand Codes or the Code Lists, first try the Brand
Code Search or the Direct Code Entry method.
Keep pressing PLAY every 5 seconds until your device
turns off.
Each device key is associated with a type of device—the
TV is preset to search for TVs, SAT•CBL•STRM for
satellite receivers, cable boxes or digital TV converters
or streaming media players, DVD•VCR for DVD players,
and DVR•AUX for DVRs. To program a device key for
a different type of device, see the Changing a Key’s
Device Type section.
5. When your device turns off,
press the REVERSE key on
the remote and wait at least 2
seconds. The remote tries the
last of the previous ten codes.
Did your device turn on?
To exit without saving a new code at any point in the
Manual Code Search, press the CLEAR key.
YES: Press the STOP
key. You’re done! You’ve
programmed this device key.
NO: Press REVERSE again. The remote tests the next
code in the batch.
1. Manually turn on the device
you want to control.
Keep pressing REVERSE every 2 seconds until your
device turns back on. When it does, press STOP.
Note: If you accidentally press the REVERSE key after
your device turns on, press the FORWARD key. Then, wait
two seconds to see if your device turns off again.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press and hold the device key you want to program.
While you’re holding down the device key, use your
other hand to press and hold the remote’s POWER key
at the same time.
Tour of the Remote
In most cases, the keys on
this remote perform the
same functions as the keys
on your original remotes
once you’ve programmed
this remote to operate your
devices. Many keys on this
remote have other functions
as well.
3. Wait until the POWER key comes
on and stays on. Then release
both keys.
Device keys (TV,
SAT•CBL•STRM, DVD•VCR,
DVR•AUX) put the remote
in the right mode to control
your device.
4. Keep the remote pointed directly at the front panel of the
device you want to control. Press POWER on the remote
and wait 2 seconds. The remote is testing a single code
for your device.
GUIDE•HOME and MENU
access the same features
as the keys on your original
remotes.
Arrow keys act as
navigation keys for
Did your device turn off?
streaming media players as
well as in menu and guide
systems for other devices.
YES: Press the STOP key to store
the code. You’re done! You’ve
programmed this device key.
CLEAR exits remote
programming; it also
performs the same
functions as on your
original remotes.
NO: Press POWER again. The
remote tests the next code for
your device.
Keep pressing POWER every 2
seconds until your device turns off.
When it does, press STOP.
CHAN and VOL keys act
as channel and volume
controllers.
TIP: Because there are so many codes, you may have to
press the POWER key many times—possibly hundreds of
times.
The INPUT and — (dash)
key has three functions: (1)
it toggles through all the
video sources connected
to your TV; (2) when the
remote is in VCR mode, this
button toggles between
VCR and the TV input; (3)
when you’re entering digital
channel numbers directly,
this button lets you separate
the main channel number
from the sub-channel
NOTES
Throughout the programming of each key, keep the
remote pointed at the IR sensor of the device you are
programming the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don’t work, try
a different code. See the “Testing the Code for Maximum
Functionality” section below for more information.
Actual model may vary from
illustration
During the Manual Code Search, the remote ignores
keypresses that aren’t part of the search.
number (such as 59.1).
The search times out after two minutes (the POWER key
blinks four times and turns off, and the last programmed
code under that device key is retained).
IMPORTANT
The POWER key blinks four times and turns off when the
remote has gone through all the codes. The remote exits
the Brand Code Search. If your device hasn’t turned off
yet, try a different search method.
Because this remote controls more than one device,
you must first “tell” the remote which device you wish
to operate. That means, if you wish to operate your TV,
you must first press the TV key to put the remote in the
TV Mode. The remote stays in that device mode until
you press a different device key. For example, if your
remote is in TV Mode and you want to operate the DVD
player, you must press the DVD key to change device
modes.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote.
If some features of your devices don’t work, go to the
next step to try a different code.
2. Repeat the Manual Code Search and Entry Method
from the beginning. When the device turns off for the
first time, don’t press the STOP key, which would store
the same code. Instead, with the unit now off, continue
to press the POWER key repeatedly until the unit turns
back on.
Backlighting
Backlight illumination helps you see the remote control
keys better in the dark.You can turn backlight illumination
on or off by pressing the backlight key ( ). Backlighting
stays on as long as keys are being pressed and turns off six
seconds after the last keypress. Once the backlight time has
timed out, any keypress will reactivate it. If the backlight
illumination is on, and you press the backlight key, the
backlight turns off.
3. Once the unit turns back on, you have found another
code that operates the device. Press the STOP key.
4. Test the key’s functionality again by trying a variety
of functions. If the code controls the majority of the
device’s functions, programming is complete. If the
code stored does not give maximum functionality, try
another code.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. While holding the device key down, press and hold
the INFO key. The POWER key turns off. After holding
down both keys for three seconds, the POWER key
turns back on.
Advanced Functions
Changing A Key’s Device Type
3. Release both keys. The POWER key remains on.
Each device key is associated with a type of device—the
TV is preset to search for TVs, SAT•CBL•STRM for satellite
receivers, digital TV converters or streaming media players,
or cable boxes, DVD•VCR for DVD players or VCRs, and
DVR•AUX for DVRs. To program these keys to control a
different kind of device, you have to reassign them first.
4. Starting with the number 1 key, press and release each
number key on the keypad in the following order: 1-9,
then 0. The number that causes the POWER key to
blink is the first number of the code. As you find each
number of the code, write it down for future reference.
Note: All TV codes begin with the number 1; all VCR
and DVR codes begin with the number 2; all DVDs, the
number 3; and all satellite receivers, digital TV converters
or streaming media players, and cable boxes, the number
5.
Reassigning the DVD•VCR Key to Control a VCR
The DVD•VCR key defaults to control a DVD player. If you
want the DVD•VCR key to control a VCR, you must reassign
it.
1. Press and hold the DVD•VCR key. The POWER key
turns on. Keep holding down the DVD•VCR key.
5. Repeat step 4 until you have retrieved all five numbers
in the code. After the fourth number is retrieved, the
POWER key blinks briefly, then turns off.
2. While holding down the DVD•VCR key, press and
release the number 2 key on the keypad. The POWER
key turns off.
TIP: To exit the Code Retrieval Mode at any time, press
the CLEAR key.
3. Release the DVD•VCR key. The POWER key blinks four
times and then turns off. The DVD•VCR key is now set to
control a VCR.
Note: If you press an invalid key during the Code
Retrieval process, the remote will not respond. If you do
not press a valid Code Retrieval key (TV, SAT•CBL•STRM,
DVD•VCR, DVR•AUX, INFO, CLEAR), Code Retrieval times
out after 15 seconds. The POWER key blinks four times,
and then turns off.
4. Follow the directions in the auto, brand, direct entry, or
manual code search to program the DVD•VCR key for
your VCR.
Reassigning the DVR•AUX Key To Control Other
Devices
TV CODE
SAT•CBL•STRM CODE
The DVR•AUX key defaults to control a DVR. If you want the
DVR•AUX key to control a different device (an additional
TV, DVD, satellite, digital TV converters or streaming media
players, or cable box, for example), you must reassign it.
1
5
SAT
CABLE
DTV CONVERTER
1. Press and hold the DVR•AUX key. The POWER key
turns on.
2. While holding down the DVR•AUX key, press and release
the number key on the keypad for the device you wish to
control (see the chart below). The POWER key turns off.
DVD•VCR CODE
DVR•AUX CODE
DVR•AUX KEY CONTROLS:
DVD
VCR
DVR/VCR
DVD
TV
SAT•CBL•STRM
Additional TV
VCR or DVR
press 1
press 2
press 3
press 5
Additional DVD
Troubleshooting
Additional satellite, digital TV
converters or streaming media
players, or cable box
Problem: The remote does not operate your device.
•
•
•
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STRM, DVD•VCR,
DVR•AUX). This tells the remote which device to operate.
3. Release the DVR•AUX key. The POWER key blinks four
times and then turns off. The DVR•AUX key is now set
to control the device type you selected.
Remove any obstacles between the remote and the device.
Make sure you’re aiming the remote at the device’s IR
sensor.
4. Follow the directions in the auto, brand, direct entry, or
manual code search to program the DVR•AUX key.
Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AAA batteries, if
necessary (see the Battery Installation section).
Code Retrieval
Once you’ve programmed the remote to control your
devices, you may want to record the codes for future
reference. If you used the Direct Code Entry method, this
is easy. Just find the codes you entered and make a note
of them in the boxes below. If you used one of the Code
Search methods to program your remote or if you used the
Direct Entry method but don’t remember the code, you will
need to retrieve each device’s five-digit code. Retrieving
the actual code and writing it down will save you time
if you ever need to program the remote again (e.g., if
programming is lost when you change the batteries). If the
codes are recorded, you can use the Direct Entry method
to reprogram your remote to control your devices, which is
quick and easy.
Problem: The remote can’t be programmed to operate
your device.
•
If you are testing the remote while programming it, you may
be too far away from the device or at a wrong angle. There
must be an unobstructed path between the remote and the IR
sensor on the device. Move closer and make sure you point the
remote at the device you’re trying to control.
•
•
If you’re using the Direct Entry programming method
to enter the codes for your brand and the unit is still not
functioning properly, try the auto, brand, or manual search
method.
To control combo units, like TV/VCRs or TV/DVDs, you must
program the individual corresponding device keys to control
each part of the combo unit. Once programmed successfully,
the TV key controls the TV functions, and the DVD•VCR key
controls the VCR or DVD functions.
1. Press and hold the device
key (TV, SAT•CBL•STRM,
DVD•VCR, DVR•AUX) whose
code you wish to retrieve.
The POWER key turns on.
Keep pressing the device key.
•
Make sure the batteries are fresh and are properly installed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: The remote doesn’t perform commands properly.
Limited Lifetime Warranty
•
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STRM, DVD•VCR,
DVR•AUX). This tells the remote which device to operate.
VOXX Accessories Corporation (the “Company”) warrants to you the
original retail purchaser of this product that should it, under normal use
and conditions, be proven defective in material or workmanship during
its lifetime while you own it, such defect(s) will be repaired or replaced
(at the Company’s option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the
product is to be delivered with proof of warranty coverage (e.g. dated bill
of sale), specification of defect(s), transportation prepaid, to the Company
at the address shown below.
•
•
•
Make sure device is ready (for example, the DVD player has
a disc loaded).
You may have pressed an invalid key for the mode the remote is
in.
If you’re trying to enter a channel number directly, try
pressing the OK key after entering the channel number as
this is a requirement of certain models and brands.
This Warranty does not cover product purchased, serviced or used
outside the United States or Canada. This Warranty is not transferable
and does not extend to costs incurred for installation, removal or
reinstallation of the product. This Warranty does not apply if in the
Company’s opinion, the product has been damaged through alteration,
improper installation, mishandling, misuse, neglect, accident, or the
simultaneous use of different battery types (e.g. alkaline, standard or
rechargeable).
•
There is a possibility that a programmed code may only be
able to control some of your device features (for example,
only turns a device on and off). To confirm that the device
key is programmed with the correct code for maximum
functionality, test the device. Attempt to control a variety
of the device’s functions with the remote. If some of the
features of your devices don’t work, try programming the
remote with a different code in the list using the Direct Code
Entry Method, until you find the code that allows the remote
to control the majority of your device’s functions. Different
codes can provide different levels of functionality.
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE
AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL
BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL
THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES WHATSOEVER. No person or representative is authorized
to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Problem: The POWER key does not light when you press a
key.
•
You may have pressed an invalid key for the mode the
remote is in.
•
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STRM, DVD•VCR,
DVR•AUX). This tells the remote which device to operate.
Some states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you.
This Warranty gives you specific legal rights and you may also have
other rights, which vary from state/province to state/province.
•
Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AAA batteries, if
necessary (see the Battery Installation section).
U.S.A.: Audiovox Return Center, 150 Marcus Blvd., Hauppauge, New
York 11788
Problem: The remote will not change channels on device.
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
Unit 3, Door 16, Mississauga, Ontario L5T 3A5
•
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STRM, DVD•VCR,
DVR•AUX). This tells the remote which device to operate.
•
•
Press the OK key after you enter a channel number.
Remove any obstacles between the remote and the device.
Make sure to aim the remote at the IR sensor on the device.
Problem: The device’s menu does not appear on the TV
screen.
•
•
•
Make sure you have connected the device to your TV properly
and selected the correct input. (See your devices’ Owner’s
Manuals for proper connection procedures.)
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•STRM, DVD•VCR,
DVR•AUX). This tells the remote which device to operate.
Menu access isn’t supported for all brands. You may need to
use your original remote control to access menu functions
for some devices.
For more information, please visit
Consumer Help Line: 1-800-420-7968
Care and Maintenance
• Keep the remote dry. If it gets wet, wipe it dry
immediately.
• Use and store the remote only in normal temperature
environments.
• Handle the remote gently and carefully. Don’t drop it.
• Keep the remote away from dust and dirt.
• Wipe the remote with a damp cloth occasionally to keep it
looking new.
• Modifying or tampering with the remote’s internal devices
can cause malfunction and invalidate its warranty.
©2012 Voxx Accessories Corp.
3502 Woodview Trace, Suite 220
Indianapolis, IN 46268
Trademark(s) ® Registered
RCRBB04GR US 03
Download from Www.Somanuals.com. All Manuals Search And Download.
|