RF-RBWS01 Wireless Bookshelf Speakers
Package contents
Connecting power to the wireless speaker
Establishing communication
Connect the AC power adapter to the wireless
speaker and plug into an AC power outlet. The
wireless speaker system turns on automatically.
The wireless sender/receiver and wireless speakers were pre-joined so they will communicate with
each other right out of the box. So if this is your first Rocketboost enabled product you can skip
this section and go to the next section, Listening to music.
AC power adapter
for wireless speakers
Rocketboost network notes:
Every Rocketboost network must contain
one hub device, which helps devices join
the network. The network can have only
one hub, which you can enable using the
hub switch on the back of all Rocketboost
wireless sender and wireless
DC IN
15V/1.5A
3.5 mm
audio cable
AC power adapter
for wireless sender/receiver
If you need to rejoin the wireless sender/receiver to the wireless speakers, and this is your only
Rocketboost enabled product, then use the following steps.
1 Set the HUB STATUS switch on the wireless sender/receiver to ENABLE if this is your first
Rocketboost product set.
Wireless sender/receiver
DC IN
15V/1.5A
sender/receivers. If this is your first
Rocketboost product, you should make
the wireless sender/receiver the hub, if you
already have Rocketboost products, you
should disable hub mode on this device.
Right speaker
back
•
•
The power indicator turns green when the HUB STATUS switch is set to ENABLE.
The power indicator turns blue when the HUB STATUS switch is set to DISABLE.
3.5 mm to RCA adapter
(6 inches/15.25 cm)
USB cable
Remote control
2 Press and hold on the wireless sender/receiver for more than three seconds to put it into
joining mode. The power indicator starts blinking rapidly and the unit will stay in joining mode
for 30 seconds.
3 Press and hold the button on the wireless speaker for more than three seconds
so the wireless sender/receiver and wireless speaker enter connection mode.
User Guide
Quick Setup Guide
Wireless speakers
Important: Hub devices must always have
power for your network to operate. The
hub device can be in standby (power-
saving) mode, but must stay plugged in.
Connecting audio source and power to wireless sender/receiver
1 Connect your audio source to the LINE IN jack or USB jack on the rear of the wireless sender,
using the 3.5 mm audio cable or the USB cable. If necessary, you can also use the 3.5 mm to RCA
adapter, if your audio device uses RCA-type line out connectors.
Initial setup
1
2
Unpack the package contents
•
•
The power indicator lights steadily if the joining was successful.
The power indicator blinks slowly if the joining was not successful.
Adjust the antennas
Included 3.5 mm cable
and 3.5 mm to RCA adapter
Adjust the antennas to gain the best audio signals.
Tip: In some cases, you may improve range by rotating
both antennas 0° to create a 180° angle.
Included 3.5 mm cable
To audio output jack
4 After the link is established, if the Source indicator on
the wireless speaker is still not illuminated, make sure
that your source is turned on.
OR
To audio
output jack
Lights when
speaker is
receiving
audio from
sender
standby
For more instructions, see your User Guide.
3
4
Enable the remote control battery
Remove the tab from the bottom of
the remote control.
SOURCE
If you already have other Rocketboost devices you need
to join both the wireless sender/receiver and the wireless
speaker to your existing hub device. See the User Guide
for detailed instructions on how to do this.
Included USB cable
Set up the wireless sender/receiver
and wireless speaker
To USB jack
Listening to music
The Quick Setup Guide will show you a typical
setup using an audio device (such as an MP3
player, PC or A/V receiver). For more information
about how to use other Rocketboost products
with this product, see your User Guide.
See the following steps for further setup details.
2 Remember to turn the volume up on your audio source especially if connected to a headphone
1 Turn on the wireless sender/receiver and wireless speaker. The power indicator LEDs should
light steadily. If they are blinking you need to rejoin the wireless sender/receiver and wireless
speaker. See the Establishing communication section above.
output.
3 Connect the AC power adapter to the wireless USB sender/receiver and plug into an AC power
outlet.
2 Point the remote control at the wireless sender/receiver and select either USB-In or LINE-In
depending on which audio input you are using.
RF-RBUSB
Wireless
sender/receiver
RF-RBWS01
Wireless
speakers
The wireless sender/receiver automatically turns on and the power indicator turns green.
3 Play music from the audio device connected to your wireless sender/receiver and listen to it
from the wireless speakers.
4 Adjust the volume level on your wireless speaker. If you have multiple audio sources in your
Rocketboost network, press the Source button on the wireless speaker to hear the next audio
source. Press the Source button again to cycle through all available audio sources.
Note: Be sure to turn up the volume on your audio source device, especially if you are
connected to a headphone output.
© 2011 BBY Solutions, Inc. All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richfield, MN USA 55423-3645
ENGLISH 11-0203
QUICK SETUP GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
|