RCR311W
Universal Remote Control
Owner’s Manual
Manual del Propietario (parte posterior)
Tip: The three-component universal remote is already programmed
Illuminated ON/OFF key
Serves as an indicator
light to provide
to operate most RCA, GE and PROSCAN branded TVs,
DVD players and satellite receivers. Just press the corresponding
key—VCR•DVD for a DVD player; TV for a television; SAT•CBL
for a satellite receiver.
feedback.
Component keys. (tv,
vcr•DvD, SAt•cBL)
Battery Installation and Information
Your universal remote requires two AA Alkaline batteries
(batteries may or may not be included, depending on model).
Backlight key Turns
backlighting on/off.
To install the batteries:
1. Remove the battery compartment cover.
INFO key Displays
information pertaining
to the component you
are currently controlling.
2. Insert the batteries, matching the
batteries to the (+) and (-) marks inside
the battery compartment.
cH and vOL keys have
dual functions. They act
as navigation keys (up,
down, right, and left
arrow keys) in menu
systems.
3
Press and push the battery cover back
into place.
Note: If you are replacing batteries, try not to press any keys after
you’ve taken the old batteries out. Pressing keys while replacing
batteries causes the remote to lose the components you’ve programmed.
You will need to program the remote again.
Dedicated MENU key
for DVD disc menus,
satellite receivers and
some TVs.
Battery Precautions:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-
cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly and recycle or
dispose of them in accordance with Local and National Regulations.
SLEEP key Allows you
to set a time to turn off
your TV automatically.
INPUt key On some
remotes, this is called
the TV/VCR key. It toggles
through all the video
sources connected to
your TV.
Battery Saver
Your universal remote control saves battery power by
automatically turning off if any key is pressed for more than
60 seconds. This saves your battery life should your remote
get stuck in a place where the keys remain depressed, such as
between sofa cushions.
Transport
keys rEvErSE, PLAY,
FOrWArD, rEcOrD,
StOP and PAUSE keys.
Backlighting
Backlight illumination enables you to see the remote
control keys better in the dark. Backlight illumination
is toggled on or off with successive keypresses of the
backlight key. When toggled on, the backlighting remains on
as long as keys are being pressed. The backlighting turns off
six seconds after the last keypress. Once the backlight time
has expired, any keypress will reactivate backlighting. If the
backlight illumination is on, and the backlight key is pressed,
the backlight turns off.
Actual model may vary from picture shown
Three-Component
Universal Remote
Illuminated ON•OFF Key
Congratulations on your purchase of this three-component universal
remote. This universal remote controls up to three electronic
components and makes juggling remote controls a thing of the past.
Your remote is guaranteed to work with all brands of components.
The three-component universal remote is easy to use, easy to
program and gives you control at the touch of your fingertips.
The ON•OFF key powers components on and off. It also
lights up to serve as an indicator light, providing feedback for
various functions. When a valid key is pressed, the illuminated
ON•OFF key remains lit as long as the key is pressed and turns
off when the key is released. The ON•OFF key also blinks in
Programming Mode or in Menu Mode to provide feedback.
SAVE THIS MANUAL AND THE CODE LISTS!
Remote controls can sometimes lose their programming when you
change the batteries. Make sure you keep the manual and code lists in
a safe place so that you can reprogram the remote if you need to.
• Keep the remote away from dust and dirt.
Care and Maintenance
• Wipe the remote with a damp cloth occasionally to keep it looking
new.
• Keep the remote dry. If it gets wet, wipe it dry immediately.
• Use and store the remote only in normal temperature
environments.
• Modifying or tampering with the remote’s internal components
can cause malfunction and invalidate its warranty.
• Handle the remote gently and carefully. Don’t drop it.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip: To exit without saving at any point in the Manual
Code Search, press and release the GO BACK key.
Direct Code Entry
To program your universal remote to control your components
using the Direct Code Entry Method, follow the steps below.
1. Manually turn on the component you want the remote to
control.
1. Manually turn on the component you want the remote to
control.
Note: If you press an invalid key during the Manual Code Search,
the remote does not respond and the search times out after two
minutes. When the search times out, the illuminated ON•OFF key
blinks four times and turns off. The last programmed code under
that component key is retained.
2. Locate the enclosed Code Lists. Find the list for the
component you wish to program. Find your component’s
brand. You will see a listing of four-digit codes for each
brand. If your brand isn’t listed, use one of the Code Search
methods to program the remote control. (Refer to pages 3
and 4 for Manual and Auto Code Search methods.)
2. If you are programming the remote to control your TV,
satellite receiver or cable box, go directly to step 4.
Note: You can also use the online code finder at
3. To program the remote to control a VCR or DVD. The
VCR•DVD key can control only one component, either
your VCR or your DVD. To program your remote to
control either your DVD or your VCR, you must first put
the remote in the proper programming mode. Follow these
directions before proceeding to step 4.
3. Press and hold the component key (TV,
VCR•DVD, SAT•CBL) you wish to
program. The illuminated ON•OFF key
turns on and remains on. If you release
the component key at any time during the Direct Code
Entry procedure, the illuminated ON•OFF key blinks four
times, and the process is exited.
a. Press and hold the VCR•DVD key. The illuminated
ON•OFF key turns on.
b. While holding down the VCR•DVD key, press and release
the number 2 key on the keypad to control a VCR or
the number 3 key to control a DVD. The illuminated
ON•OFF key turns off.
4. While holding down the component key, consult the
Code Lists for the four-digit code that corresponds to your
component’s brand and use the number keys (0-9) on the
keypad to enter it. While you are pressing the numbers, the
illuminated ON•OFF key turns off.
c. Release the VCR•DVD key. The illuminated ON•OFF key
blinks four times and then turns off. Your remote is now
either in VCR or DVD Programming Mode, depending
on which you chose. Proceed to step 4.
5. After the fourth number is entered, the illuminated ON•OFF
key turns on. At this time, release the component key. If the
illuminated ON•OFF key turns off, you have entered a valid
code and have followed the correct procedure for Direct
Code Entry.
4. Press and hold the component key (TV, VCR•DVD,
SAT•CBL) you wish to program. The illuminated ON•OFF
key turns on and remains on.
If you enter a code number that is not in the Code Lists or
you do not follow all of the steps for Direct Code Entry,
the illuminated ON•OFF key blinks four times when the
component key is released. This is an indication that a
programming error has occurred. In that case, repeat the
Direct Code Entry process from step 3.
5. While holding the component key down,
press and hold the ON•OFF key. The
illuminated ON•OFF key turns off.
6. After holding down both keys for three seconds, the
illuminated ON•OFF key turns back on.
Tip: Throughout the programming of each key, be sure to keep the
remote pointed at the IR sensor of the component you are currently
programming the remote to control.
7. Release both keys. The illuminated ON•OFF key remains
on.
Tip: Throughout the programming of each key, be sure to keep the
remote pointed at the IR sensor of the component you are currently
programming the remote to control.
6. To confirm that the component key is programmed with
the correct code for maximum functionality, test the
component. Attempt to control a variety of the component’s
functions with the remote. If some of the features of your
components do not work, try programming the remote with
a different code in the list until you find the code that allows
the remote to control the majority of your component’s
functions. Different codes can provide different levels of
functionality.
8. Press and release the ON•OFF key repeatedly, waiting 4
seconds between each key press, until your component turns
off. Each time you press the ON•OFF key, the illuminated
ON•OFF key blinks, and the next code is sent. This process
continues until all of the codes in the Code Lists have been
searched. If your component turns off, you have found
the correct code. (If it cycles through and the illuminated
ON•OFF key blinks four times and turns off, all codes have
been searched. The Manual Code Search method is exited.)
7. Remember to enter the code for future reference in the box
provided in the Code Retrieval section of this manual (See
page 5).
9. Once your component turns off, you have found
the correct code. You must save the new code
by pressing and releasing the STOP key. The
illuminated ON•OFF key turns off. You must press
the STOP key to save the code or the correct code
will not be stored!
Manual Code Search and Entry
If your component’s brand isn’t listed in the Code Lists, or if
you have tried all of the codes for your brand and the remote
does not operate your component, try one of the Code Search
methods below—Manual Code Search or Auto Code Search.
Both Code Search methods cycle through all of the codes in
the Code Lists in the event that your component’s code is
listed under another brand.
The Manual and Auto Code Search methods may take a long
time because the remote searches through all of the codes in its
memory for the code that operates your component. Therefore,
if your brand is listed in the Brand Codes or the Code Lists,
first try the Brand Code Search or the Direct Code Entry
methods described on pages 2 and 3.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Release the VCR•DVD key. The illuminated ON•OFF key
blinks four times and then turns off. Your remote is now
either in VCR or DVD Programming Mode, depending
on which you chose. Proceed to step 4.
Testing the Code for
Maximum Functionality
To confirm that the component key is programmed with the
correct code for maximum functionality, it is necessary to test the
component. If some of the features of your component do not
work, different codes in the list can be tried until you find the code
that allows the remote to control the majority of your component’s
functions. Different codes can provide different levels of
4. Press and hold the component key (TV, VCR•DVD,
SAT•CBL) you wish to program. The illuminated ON•OFF
key turns on and remains on.
5. While holding the component key down,
press and hold the ON•OFF key. The
illuminated ON•OFF key turns off.
functionality. Follow these steps to test for maximum functionality.
1. Once the code has been stored (see Manual Code Search and
Entry Method, page 3), use the remote to attempt to control a
variety of the component’s functions. If the code that has been
stored controls the majority of the component’s functions,
programming is complete. If the code stored does not give
maximum functionality, you will want to try another code.
6. After holding down both keys for three seconds, the
illuminated ON•OFF key turns back on.
7. Release both keys. The illuminated ON•OFF key remains
on.
Tip: Throughout the programming of each key, be sure to keep the
remote pointed at the IR sensor of the component you are currently
programming the remote to control.
2. In that case, repeat the Manual Code Search and Entry Method
from step 1. When the component turns off for the first time,
do not press the STOP key, which would store the code. Instead,
wait 4 seconds, with the unit now off, continue to press the
ON•OFF key repeatedly until the unit turns back on. Once the
unit turns back on, you have found another code that operates
the component. Press the STOP key.
8. Press and release the PLAY key,
then wait five seconds to see if
your component turns off. If your
component does not respond,
continue to press the PLAY key
every five seconds until your
component turns off. Each time
you press the PLAY key, the
illuminated ON•OFF key blinks
and a block of 10 codes are sent
to your component. This process
continues until all of the codes
in the Code Lists have been
searched. (If your component has
not turned off after all codes have
been searched, the illuminated
ON•OFF key blinks four times
and turns off. The Auto Code
Search Entry method is exited.)
3. Test the functionality again by attempting to control a variety
of the component’s functions. If the code that has been
stored controls the majority of the component’s functions,
programming is complete. If the code stored does not give
maximum functionality, you will want to try another code.
4. Repeat the Manual Code Search and Entry Method from step
1. Each time a code turns the component on or off, you have
found a code that operates the remote and needs to be tested
for maximum functionality. Continue through the code lists,
cycling through the codes you have already tried, until you find
one that offers maximum functionality.
Auto Code Search and Entry
The Auto Code Search and Entry Method enables the remote
to automatically search through all the codes in the Code Lists
for the one that operates your component.
9. When your component turns off, you know the
correct code is in the last block of 10 codes sent.
Press and release the REVERSE key. Wait two
Note: The Manual and Auto Code Search methods may take a long
time because the remote searches through all of the codes in its memory
for the code that operates your component. Therefore, if your brand is
listed in the Brand Codes or the Code Lists, first try the Brand Code
Search or the Direct Code Entry methods described on pages 2 and 3.
seconds to see if your component turns on again. If
your component does not respond, continue to press the
REVERSE key every two seconds until your component
turns on again. This will isolate the correct code in the last
block of codes sent. Each time the REVERSE key is pressed,
the illuminated ON•OFF key blinks.
Tip: To exit without saving at any point in the Auto
Code Search, press and release the GO BACK key.
Note: If you accidentally press the REVERSE key after your
component responds, press and release the FORwARD key.
Then, wait two seconds to see if your component turns off
again.
1. Manually turn on the component you want the remote to
control (TV, VCR, DVD, satellite receiver or cable box).
Note: If you press an invalid key during the Auto Code Search,
the remote does not respond. If you do not press a valid Auto Code
Search key (TV, VCR•DVD, SAT•CBL, ON•OFF, GO BACK,
PLAY, REVERSE, FORwARD, STOP), the search times out
after two minutes. When the search times out, the illuminated
ON•OFF key blinks four times and turns off. The last programmed
code under that component key is retained.
10.Once your component turns off, you have found
the correct code. You must save the new code by
pressing and releasing the STOP key. The illuminated
ON•OFF key turns off. You must press the STOP
key to save the code or the correct code will not be
stored!
2. If you are programming the remote to control your TV,
satellite receiver or cable box go directly to step 4.
11.To confirm that the component key is programmed with
the correct code for maximum functionality, test the
component. Attempt to control a variety of the component’s
functions with the remote. If some of the features of your
components do not work, different codes in the list can
be tried until you find the code that allows the remote
to control the majority of your component’s functions.
See the section entitled “Testing the Code for Maximum
Functionality” on page 4 for more information.
3. To program the remote to control a VCR or DVD. The
VCR•DVD key can control only one component, either
your VCR or your DVD. To program your remote to
control either your DVD or your VCR, you must first put
the remote in the proper programming mode. Follow these
directions before proceeding to step 4.
a. Press and hold the VCR•DVD key. The illuminated
ON•OFF key turns on.
b. While holding down the VCR•DVD key, press and release
the number 2 key on the keypad to control a VCR or
the number 3 key to control a DVD. The illuminated
ON•OFF key turns off.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing and Selecting Menu Items
Code Retrieval
Today’s advanced components use on-screen menus to
help you navigate through all their features and functions.
While this remote cannot access every menu system of every
component model, it does offer some menu functionality.
Once you’ve programmed the remote to control your
components, you may want to record the codes for future
reference. If you used the Direct Code Entry method, this is
easy. Just find the codes you programmed in and make a note
of them in the boxes on this page. If you used one of the Code
Search methods to program your remote, you will need to
retrieve each component’s four-digit code. Retrieving the actual
code and writing it down will save you time if you ever need
to program the remote again (e.g., if programming is lost when
you change the batteries). If the codes are recorded, you can use
the Direct Entry method to reprogram your remote to control
your components, which is quick and easy.
To use a component’s on-screen menu system, you first have to
put the remote in Menu Mode.
1. Make sure your components are turned on and your TV is
set to the component’s input. (Use the INPUT key to toggle
through video sources when in TV mode.)
2. Press the component key whose menu you want to access.
3. Press the MENU key. The illuminated
ON•OFF key blinks, indicating you are in
the Menu Mode.
1. Press and hold the component key (TV,
VCR•DVD, SAT•CBL) whose code you
wish to retrieve. The illuminated ON•OFF
key turns on.
4. Use the VOL+/- and CH+/-keys to
navigate through the on-screen menu
system.
2. While holding the component key
down, press and hold the INFO key. The
illuminated ON•OFF key turns off.
5. To make a selection from the on-screen menu, press
the MENU or OK key to select the highlighted item.
3. After holding down both keys for three seconds, the
illuminated ON•OFF key turns back on.
Tip: If the remote doesn’t respond, check to see that the
illuminated ON•OFF key is still blinking. Note: it times
out after 20 seconds. If this happens, just press the MENU
key again, and then retry your selection.
4. Release both keys. The illuminated ON•OFF key remains on.
5. Starting with the number 1 key, press and release each
number key on the keypad in the following order (1-9, then
0). The number that causes the illuminated ON•OFF key
to blink is the first number of the code. As you find each
number of the code, refer to the code boxes below and write
them down for future reference.
Exiting Menu Mode
The remote automatically times out of Menu Mode after 20
seconds of inactivity (no keys being pressed). At that time, the
remote clears the displayed menu from the TV.
If you want to exit the Menu Mode yourself, press the
corresponding component key on the remote (TV, VCR•DVD,
SAT•CBL). The illuminated ON•OFF key turns off.
Note: All TV codes begin with the number 1; all VCR codes
begin with the number 2; all DVDs, the number 3; and all satellite
receivers and cable boxes, the number 5.
6. Repeat step 5 until you have retrieved all four numbers in
the code.
Sleep Timer
This feature automatically turns off your TV at a duration you
choose from 1 to 99 minutes. The Sleep Timer only works
if you have found a code that controls your TV. The timing
mechanism for the Sleep Timer is built into your universal
remote control. To program the Sleep Timer, follow these steps.
7. After the fourth number is retrieved, the illuminated
ON•OFF key blinks briefly, then turns off.
8. To exit the Code Retrieval Mode, press and release the GO
BACK key at any time.
9. If you press an invalid key during the Code Retrieval process,
the remote will not respond. If you do not press a valid Code
Retrieval key (TV, VCR•DVD, SAT•CBL, INFO, GO BACK),
Code Retrieval times out after 15 seconds. The illuminated
ON•OFF key blinks four times, and then turns off.
Programming the Sleep Timer
1. Press and release the TV key.
2. Press and hold the SLEEP key for three seconds.
The illuminated ON•OFF key turns on.
TV Code
SAT•CBL Code
3. Release the SLEEP key.
4. Using the number keys, enter the desired time in minutes
(from 1-99 minutes). To set the timer to a number under 10
minutes, first press 0 and then the desired number (e.g., 05
for five minutes). The illuminated ON•OFF key blinks with
each keypress.
1
5
SAT
CABLE
VCR•dVd Code
5. Once the second number is entered, the illuminated
ON•OFF key turns off.
VCR
DVD
Tip: Any keypress other than the number keys is ignored. If you don’t
enter the sleep time within 10 seconds after pressing the SLEEP key,
you must start over at step 1. The illuminated ON•OFF key blinks
four times and then turns off, indicating your attempt to program the
Sleep Timer has been unsuccessful.
Using the Remote to Control
Your Components
Because this remote controls more than one component, you
must first “tell” the remote which component you wish to
operate. That means, if you wish to operate your TV, you must
first press the TV key to put the remote in the TV Mode.
6. The Sleep Timer is now set.
7. Leave remote aimed at the TV. Once the Sleep Timer is set,
you can continue to use the remote without affecting the
Sleep Timer. However, because the timing mechanism for
the Sleep Timer is built into the remote itself, the remote
must be in TV Mode and pointed at the TV to activate the
Sleep Timer.
The remote stays in the chosen component mode (such as TV
Mode) until you change it. If your remote is in TV Mode, you
must change the mode in order to operate your DVD or VCR,
satellite receiver or cable box. For example, if you are in VCR
Mode, and you wish to turn off your TV, you must press the
TV key first before pressing the ON•OFF key.
Canceling the Sleep Timer
1. The Sleep Timer program will be canceled and reset to zero
by pressing and releasing the ON•OFF key.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: The VCR won’t record.
Troubleshooting
Problem: The remote does not operate your
component.
•
•
•
Make sure the remote is in VCR Mode.
Make sure the tape is properly loaded in the VCR.
Make sure the tape is not write-protected. If the safety tab is
removed, the tape is write-protected, and you cannot record onto
that tape.
•
You must put the remote in the correct mode by pressing the
corresponding component key (TV, VCR•DVD, SAT•CBL) so
the remote knows which component you want to operate.
Problem: The remote will not change channels on
component.
•
•
Remove any obstacles between the remote and the component
Make sure to aim the remote at the IR sensor on the component.
•
You must put the remote in the correct mode by pressing the
corresponding component key (TV, VCR•DVD, SAT•CBL) so
the remote knows which component you want to operate.
Make sure the batteries are fresh and are properly installed. (See
Battery Installation on page 1.) Replace the batteries with two
new AA batteries, if necessary. Reprogramming may be required.
•
•
Press the OK key after you enter a channel number.
•
Reset the remote. Remove the batteries, then press and hold
the number 1 key on the remote for several seconds to reset the
microprocessor inside the remote. Release the number 1 key,
reinstall the batteries, and press the ON•OFF key. If it lights up,
reprogram the remote and try again. If it doesn’t light up, replace
the batteries with new ones.
Remove any obstacles between the remote and the component.
Make sure to aim the remote at the IR sensor on the component.
Problem: The component’s menu does not appear on
the TV screen.
•
•
•
Make sure you have connected your component to your TV
properly and selected the correct Input. (See your components’
Owner’s Manuals for proper connection procedures.)
Problem: The remote can’t be programmed to operate
your component.
•
If you are testing the remote after you have entered the code, you
may be too far away from the component or at a wrong angle.
This remote uses IR (infrared) technology to communicate with
components. The remote sends the code, and the component’s
IR sensor reads the code. Therefore, there must be an
You must put the remote in the correct mode by pressing the
corresponding component key (TV, VCR•DVD, SAT•CBL) so
the remote knows which component you want to operate.
Menu access isn’t supported for all brands. If that’s the case,
you’ll need to use your original remote control to access menu
functions for these components.
unobstructed path between the remote and the IR sensor on the
component. Move closer and make sure you point the remote
at the component (VCR or DVD player when programming the
VCR•DVD key; TV when programming the TV key; cable box or
satellite receiver when you’re programming the SAT•CBL key).
•
•
If you’ve used the Direct Entry programming methods to enter
the codes for your brand and the unit is still not functioning
properly, try one of the Code Search methods. (See Code Search
Methods on pages 2, 3 and 4.)
Limited Lifetime Warranty
To control combo TV/VCR or TV/DVD units, you must
program both the TV key and the VCR•DVD key. Once
programmed successfully, the TV key controls the TV functions
on your unit, and the VCR•DVD key controls the VCR or
DVD functions. There is a specific section in the Code Lists for
combo units. The codes in this section should be tried first using
Direct Code Entry on the TV and VCR•DVD keys. If this is
unsuccessful, follow the normal programming methods for both
the TV and the VCR•DVD keys.
Audiovox Electronics Corporation (the “Company”) warrants to you the
original retail purchaser of this product that should it, under normal use
and conditions, be proven defective in material or workmanship during its
lifetime while you own it, such defect(s) will be repaired or replaced (at the
Company’s option) without charge for parts and repair labor. To obtain repair
or replacement within the terms of this Warranty, the product is to be delivered
with proof of warranty coverage (e.g. dated bill of sale), specification of
defect(s), transportation prepaid, to the Company at the address shown below.
This Warranty does not cover product purchased, serviced or used outside the
United States or Canada. This Warranty is not transferable and does not extend
to costs incurred for installation, removal or reinstallation of the product.
This Warranty does not apply if in the Company’s opinion, the product has
been damaged through alteration, improper installation, mishandling, misuse,
neglect, accident, or the simultaneous use of different battery types (e.g.
alkaline, standard or rechargeable).
•
Make sure the batteries are fresh and are properly installed.
Problem: The remote doesn’t perform commands
properly.
•
You must put the remote in the correct mode by pressing the
corresponding component key (TV, VCR•DVD, SAT•CBL) so
the remote knows which component you want to operate.
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
•
Make sure component is “ready” (e.g., DVD player has disc
loaded; VCR has tape loaded, etc.).
•
•
You may have pressed an invalid key for the mode the remote is in.
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY.
IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
If you’re trying to turn on an RCA, GE or PROSCAN branded
component, press the component key (TV, VCR•DVD,
SAT•CBL) instead of the ON•OFF key.
•
•
If you’re trying to change channels, try pressing the OK key after
entering the channel number, as this is a requirement of certain
models and brands.
CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. No
person or representative is authorized to assume for the Company any liability
other than expressed herein in connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you. This
Warranty gives you specific legal rights and you may also have other rights,
which vary from state/province to state/province.
There is a possibility that a programmed code may only be able
to control some of your component features (e.g., only turns a
component on and off). See “Testing the Code for Maximum
Functionality” (page 4) for more information.
Problem: The illuminated ON•OFF key doesn’t light
when you press a key.
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge,
New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
Unit 3, Door 16, Mississauga, Ontario L5T 3A5
•
You must put the remote in the correct mode by pressing the
corresponding component key (TV, VCR•DVD, SAT•CBL) so
the remote knows which component you want to operate.
•
•
You may have pressed an invalid key for the mode the remote is in.
©ꢁ007 Audiovox Accessories Corporation
ꢀꢀꢀ Congressional Blvd., Suite ꢂꢄ0
Carmel, IN ꢃꢅ0ꢂꢁ
Make sure the batteries are fresh and are properly installed. (See
Battery Installation on page 1.) Replace the batteries with two
new AA batteries, if necessary. Reprogramming may be required.
Trademark(s) ® Registered
RCRꢂꢀꢀW US 00
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
|