V1.0 (EN)
Safety Precautions
Safety Precautions
User Manual
WARNING: THE APPARATUS SHALL NOT BE
EXPOSED TO DRIPPING OR SPLASHING AND THAT NO
OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL
BE PLACED ON THE APPARATUS.
ON PLACEMENT
•
Do not leave, mount or use the unit in places which are
extremely hot, cold, dusty, or humid.
•
Allow adequate air circulation to prevent internal heat build-
up. Do not place the unit on a surface or near materials (a
curtain ex. rugs, blankets, curtains, etc.) which might block
the ventilation holes.
SPS3200
CAUTION:
•
U S E O F C O N T R O L S O R A D J U S T M E N T S O R
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
The symbol for Class II
(Double Insulation)
ON CONDENSATION
•
When left in a heated room where it is warm and damp,
water droplets or condensation may form inside the CD
player. When there is condensation inside the unit, the
unit may not function normally. Let it stand for 1 to 2 hours
before turning the power on, or gradually heat the room and
allow the unit to dry before use.
SEE MARKING ON BACK OF PRODUCT
•
MAIN PLUG IS USED AS THE DISCONNECTED DEVICE,
IT SHALL REMAIN OPERABLE AND SHOULD NOT
BE OBSTRUCTED DURING INTENDED USE. TO BE
COMPLETELY DISCONNECTED THE APPARATUS FROM
SUPPLY MAINS, THE MAIN PLUG OF THE APPARATUS
SHALL BE DISCONNECTED FROM THE MAINS SOCKET
OUTLET COMPLETELY.
The lightning flash with an arrowhead symbol, within the
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to cause an electric shock.
For your safety
The AC power plug is polarized (one blade is
wider than the other) and only fits into AC power
outlets one way. If the plug won't go into the outlet
completely, turn the plug over and try to insert it
the other way. If it still won't fit, contact a qualified electrician
to change the outlet, or use a different one. Do not attempt to
bypass this safety feature.
The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in this
owner’s manual.
ON SAFETY
•
Before operating, make sure the voltage requirement of the
mains plug matches your local voltage.
•
Disconnect the mains plug immediately if liquid spills into
or onto the unit, or if an object falls into the unit. The unit
should not be used until service by a qualified service
personnel is completed.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Removing the power supply is the only way to completely
remove power from your product. Make sure the power plug
remains easily accessible.
•
•
Do not open the cabinet. Lasers used in rays employed by
the unit may damage your eyes. Any servicing should be
done by qualified service personnel.
When you are not going to use the unit for a long period of
time, disconnect the mains plug.
EN
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
It's important to read this instruction prior to using your new product for the
first time.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, THEN FULLY INSERT.
FCC Information
Before You Begin
Important Safety Instructions
Some of the following information may not apply to your
particular product; however, as with any electronic product,
precautions should be observed during handling and use.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
when moving the cart /apparatus combination to avoid injury
from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as the power cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Useful Advice
•
Do not use your system immediately after transporting it
from a cold place to a warm place, as condensation may
cause the system to malfunction. If moisture forms inside
this system, it may not operate properly. To correct the
problem, turn off the power and wait about 30 minutes for
moisture to evaporate.
•
•
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
•
•
•
This system is fitted with a laser. To avoid accidents, it is to
be opened by qualified technicians only.
Never leave the tray open as dust could cover the laser lens
and / or the tray could be bumped into accidentally.
Do not palce the system near wet areas such as bathrooms
and pool inside. Avoid storing the system at humid places or
near abnormally heated areas.
Important Battery Precautions
•
•
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (Including amplifiers)
that produce heat.
Do not defect the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong is provided for your safety.
•
Any battery may may present a risk of fire, explosion, or
chemical burn if abused. Do not try to charge a battery that
is not intended to be recharged, do not incinerate, and do
not puncture.
Non-rechargeable batteries, such as alkaline batteries, may
leak if left in your product for a long period of time. Remove
the batteries from the product if you are not going to use it
for a month or more.
Discard any leaky or deformed battery immediately. They
may cause skin burns or other personal injury.
Batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
Please help to protect the environment by recycling or
disposing of batteries according to federal, state, and local
regulations.
•
•
Ensure minimum distance around the apparatus for
sufficient ventilation. The ventilation should not be impeded
by covering the ventilation openings with items, such as
newspaper, etc.
No naked flame source, such as lighted candles, should be
placed on the apparatus.
•
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician
for help.
If the provided plug does not fit into your wall outlet, consult
an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
•
•
•
•
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user's authority to operate the equipment.
•
•
Only use attachments / accessories specified by the
manufacturer.
Use only with a cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
This Class B digital apparatus complies with Canadian ICES-
003.
This product complies with DHHS Rules 21 CFR Subchapter J.
Applicable at the date of manufacture.
Portable Cart
Warning
Mounting Instructions
STEP 3
TOOLS NEEDED:
1) Electric drill with 1/4” bit;
2) Phillips-head (cross style) Screwdriver.
c) Tape Mounting Template to the underside of the cabinet with
the folded portion of the Mounting Template flush up against
the cabinet overhang (see Figure 2). Go to STEP 2.
If your cabinet DOES have an overhang:
If your cabinet does NOT have an overhang:
a) Four screws are provided with the unit. Select the screw
length which will go completely through your cabinet bottom,
and provide at least 3/8" of thread to screw into the main
unit.
a) Four screws are provided with the unit. Select the screw
length which will go completely through your cabinet bottom,
and extend at least will go completely through your cabinet
bottom, and extend at least 3/8" past the bottom of your
cabinet overhang.
STEP 1
If your cabinet does NOT have an overhang:
b) Insert the four selected screws through each hole from the
inside of the cabinet going down (see Figure 4).
a) Place the Mounting Template in the desired location inside
or underneath the cabinet (whichever has less obstructions,
and will be easier for you to reach to drill holes), flush with
the front edge of the cabinet and tape it down. Go to STEP 2.
b) This unit includes two sets of four spacers of various lengths.
The spacers can be put together to form longer spacers
to accommodate various cabinet overhang thicknesses.
Determine the best combination of spacers which is equal to
or longer than the cabinet overhang thickness.
Figure 2
Mounting
Screw
If your cabinet DOES have an overhang:
a) Measure the thickness of the cabinet overhang (see Figure
1).
c) Insert the four selected screws through each hole from the
inside of the cabinet going down (see Figure 5).
Figure 4
STEP 2
Mounting
Screw
Use an electric drill with a ¼” bit (not included) to drill all four
holes marked on the Mounting Template (see Figure 3). To
reduce splintering, place a small piece of masking tape over
each hole location before drilling.
Figure 5
Figure 1
Go to STEP 3.
c) Hold the unit up against the bottom of the cabinet, and align
the four holes on the top of the unit with the screws. Partially
tighten each screw, but do not fully tighten the screws until
all of them have been started.
Spacer
(Optional)
d) Gently tighten each screw until they are firmly holding the
unit in place.
T
Figure 3
Go to STEP 4.
b) Fold the Mounting Template along the guideline that is
closest to the thickness (see dimension "T" in illustration) of
your cabinet overhang.
Mounting Instructions
General Controls
Front Panel Controls
d) Hold each screw head down and push the unit and spacers
onto the screws, then hold the unit up until spacers are
firmly against the bottom of the cabinet (and fully nested
within each other if you are using multiple spacers for each
screw).
b) Plug the power cord directly into the nearest wall outlet, and
wrap the remaining cord around the cord storage knob at
the rear of the unit.
MOUNTING SUGGESTIONS
e) Partially tighten each screw, but do not fully tighten the
screws until all of them have been started (see Figure 6).
f) Gently tighten each screw until they are firmly holding the
unit in place. The top front edge of the unit should clear the
overhang.
1) If your cabinet has obstructions inside it which prevent you
from using the template, cut out the corresponding area on
the template, but do NOT cut out or through the screw holes.
2) If your cabinet has obstructions underneath it, which
will interfere with the mounting of the unit, remove the
obstruction before mounting the unit, or find another location
to mount the unit.
3) It is recommended that you wear safety glasses while drilling
to prevent eye injuries.
4) For wood cabinets, you may want to mark the hole locations
with a nail, pressed gently but firmly into the wood so that a
slight impression is made. This will also help keep the drill
bit centered in the right location.
Go to STEP 4.
1. CD Drawer
2. LCD Display
3.
4.
5.
6.
POWER Button
Press to turn ON the unit or put it in STANDBY(OFF) mode.
PLAY/PAUSE Button
Press to start / pause playback of a disc.
STOP Button
Press to stop playing a disc.
9.
OPEN/CLOSE Button
Press to open / close the CD door.
10. AM/FM Band Button
11. CD·RADIO Button
Figure 6
5) Hold the drill firmly against the cabinet to keep the drill from
“walking”.
12.
REPEAT/PRESET Button
PREV/- TUNE Button
Press to repeat a single track or an entire disc(in CD mode)
/ set a radio station preset(in Radio mode).
13. CLOCK SET/MEM Button
Press to set a clock(in standby mode) / store a track in
memory(in CD stop mode).
14. TIMER Button
Press to set the cooking timer.
15. Display Button
Press to change the digits(in Timer mode) / skip to the
previous track(in CD mode) / tune in to different stations(in
Radio mode).
CAUTION:
STEP 4
TO REDUCE THE RISK OF FIRE, DO NOT PLACE ANY
HEATING OR COOKING APPARATUS BENEATH THIS
UNIT.
7.
NEXT/TUNE + Button
Plug the cord into the wall outlet
a) Before connecting power cord, make sure the voltage of the
unit matches with your local voltage.
Press to change the digits(in Timer mode) / skip to the next
track(in CD mode) / tune in to different stations(in Radio
mode).
8. VOLUME -/+ Button
Press to adjust the volume.
Download from Www.Somanuals.com. All Manuals Search And Download.
|