2000RS PLUS SERIES
REMOTE START SYSTEM
PRODUCT MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1
1.
2.
Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Two Car Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
3.
4.
System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Remote Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Remote Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Optional Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Remote Start Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Remote Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Quick Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Automatic Start Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Starter Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
5.
Extended Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Ignition Door Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Ignition Door Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Dome Light Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Auxiliary Function Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Turbo Timer Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
6.
7.
System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Mounting the Control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
System Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
6-Pin Starter Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
20-Pin Main Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Plug-in Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
8.
9.
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Jumper Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
Entering System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
Default Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
Programmable System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
Branch Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15
10. Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17
11. Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
12. Two Stage Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 19
13. Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 23
14. Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Page
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your System
The ScyTek Galaxy Starter is a started-of-the-art remote starting system featuring a built-in "ScyNet
Network Port" that allows direct connection of optional accessory modules and a PC interface offering
expanded system operation. With proper installation this system will provide superior protection and
performance for many years to come.
The Galaxy Starter’s built-in remote start feature is designed to offer maximum convenience by remote
starting your vehicle’s engine, turning on the heater/air conditioner, and then running for a pre-determined
time to provide a comfortable environment once you enter your vehicle.
To ensure the safety and security of the system while it is remote started, the Galaxy Starter employs
several safeguards. In the event the brake pedal is pressed while the engine is remotely running, the
remote start will immediately shutdown to prevent unauthorized users from attempting to drive the vehicle.
The system is equipped with a hood pin input to prevent access to the engine compartment while the
vehicle is remotely running. Finally, the Valet Mode prevents the remote start feature from operating in the
event the vehicle is to be serviced.
System Contents:
• Main Unit with built-in ScyNet Network Interface Port
• Two 5-Button Random Code Remote Transmitters
• Status LED
• Coded Emergency Override / Valet Switch
Optional ScyNet Network Interface Accessories:
• ScyNet Network Interface Software
• Two-Way FM Paging Module w/ LCD Transmitter
Options and Convenience Features*
This ScyTek system includes several optional inputs and outputs allowing the creation of a completely
personalized convenience system by offering many optional features such as:
· Second Car Operation
· Keyless Entry
· Two Stage Door Unlocking
· Horn Honk
· Illuminated Entry
· Remote Window Control
· Power Trunk / Hatch Release
· Remote Head Lamp Control
*May require additional parts and/or labor, see store for details.
PLEASE NOTE:
Some of the features described in this manual may require additional parts and/or labor, and may not be included
as part of the standard installation of this unit. Additionally, many features of this security system have
selectable options that must be activated or programmed during the system’s installation. These items will be
identified in the following sections. Please discuss these features and any questions you may have regarding the
installation of this product with Your Authorized Dealer.
Galaxy 2000RS Plus - Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Transmitters
Remote Transmitter Description
LED
Button 1
Button 3
Button 2
Button 5
Button 4
The Galaxy Starter is supplied with two 5-button Remote Transmitters used to control system operations.
Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure
the functionality of the transmitter buttons. The standard (default) setting for operation of the transmitters
is described below.
Button 1 Locks the doors and when held for 2 seconds, activates the system’s Panic feature.
Button 2 Unlocks the doors. Pressing Button 2 again operates the Passenger Unlock feature (if installed).
Button 3 Activates the Auxiliary 1 output. This output will remain on for as long as the button is pressed.
Button 4 Activates the Remote Start feature.
Button 5 is the Page Shift button. Each time the Shift Button is pressed, the LED on the transmitter will
illuminate and the transmitter functions will shift to the next page, allowing access to another set of
features. Once shifted to another page (there are 4 pages total), the transmitter will remain on that page
for 10 seconds or until a button is pressed, then return to page 1. Each time a transmitter button is pressed
and held, the LED will flash a number of times to indicate from which page it is transmitting. Under
normally operation, only pages 1 and 2 are used. Pages 3 and 4 are usually used for Two Car Operation
(see page 3) or optional expansion modules.
Shift then Button 1 Locks the system silently (only used if the optional audible status output is used).
Shift then Button 2 Unlocks the system silently (only used if the optional audible status output is used).
Shift then Button 3 Activates the Auxiliary 2 output. This output will remain on for as long as the button is
pressed.
Shift then Button 4 Activates the Auxiliary 3 output. This output will remain on for as long as the button is
pressed.
Page 2 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding/Replacing Transmitters
To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired
transmitters ready and follow the steps below.
Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored
transmitter codes, be sure to program all 4 transmitter memory locations.
To program the transmitter(s):
1. Turn on the ignition key On, Off, On, Off, and back On.
· The parking lights will flash 3 times.
2. Press and hold the Override switch for 5 seconds.
· The parking lights will flash 5 times.
· The LED will illuminate.
3. Press Button 1 on the first transmitter.
· The parking lights will flash once.
4. Press Button 1 on the first transmitter again.
· The parking lights will flash twice to indicate it has learned the code.
5. Repeat steps 3 and 4 for each transmitter (up to 4).
6. Turn off the ignition key.
· The parking lights will flash 3 times.
Two Car Operation
If two vehicles are equipped with Galaxy Starter systems, for convenience both can be operated using the
same remote transmitter. If all four transmitters are to be used with both cars, program transmitters A and
B into the first vehicle in the manner described above. Program transmitters C and D by pressing the Shift
button twice before performing steps 3 and 4 above.
When finished programming the first vehicle, program transmitters C and D into the second vehicle as
normal, then program transmitters A and B by pressing the Shift button twice before performing steps 3
and 4 above.
When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing
the Shift button twice and the desired function button.
Battery Replacement
Your Galaxy Remote Transmitter uses a 12 volt alkaline battery (type 23A), which will require replacement
in time. Depending on the amount of use, the battery may last up to six months or more before it needs
replacement.
When the battery needs replacing, the system’s operating range will decrease or the transmitter LED may
not be as bright.
In order to change the battery, first remove 2 screws from the back of the transmitter and separate the top
and bottom halves of the case.
While replacing the battery make sure that the positive and negative terminals are positioned correctly, then
carefully reassemble the transmitter case.
Galaxy 2000RS Plus - Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional 2-way LCD Remote Transmitter Description
Button 1
Button 2
Button 3
Button 4
Button 5
The Galaxy 2000RS Plus is compatible with the optional 2-way LCD remote transmitter, offering increased
range and confirmation of any activated features.
Button 1 Locks and Unlocks the system and when held for 2 seconds, activates the system’s Panic feature.
Button 1 also locks/unlocks the doors when the system is in Valet Mode.
Button 2 Activates the Remote Start feature.
Button 3 Activates the Auxiliary 1 output normally used for trunk release (note trunk icon on button).
Button 4 Activates the Auxiliary 2 output. This output will remain on for as long as the button is pressed.
Button 5 is the Confirmation and Programming button. Quickly pressing button 5 will activate the LCD
display’s backlighting for use in the dark. Pressing button 5 for 2 seconds activates the system’s
confirmation feature which will then display the current status of the system (armed, disarmed, engine
running, etc.).
Adding/Replacing Optional 2-way LCD Transmitters
When adding an optional 2-way LCD transmitter to the system, follow these steps:
1. Turn on the ignition key On, Off, On, Off, On, Off, and back On. (Key On 4 times)
· The siren will chirp 4 times.
2. Press and hold the Override switch for 5 seconds.
· The siren will chirp 4 times.
· The LED will illuminate.
3. Press Button 1 on the first transmitter.
· The siren will chirp once.
4. Turn off the ignition key.
5. Repeat steps 1-4 to add an additional 2-way transmitter.
Page 4 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Transmitter Battery Replacement
Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time.
Depending on the amount of use, the battery may last up to six months before it needs replacement. When
the battery needs replacing, the system’s operating range will decrease, the LCD display will show only one
of three bars in the battery icon, or the display and sounds may suddenly stop and start as the battery
voltage drops below minimum.
In order to change the battery, first slide the battery door locking pin to the side. Carefully slide the battery
cover downward until it is free. While replacing the battery make sure that the positive and negative
terminals are positioned correctly, then carefully reassemble the transmitter case.
Galaxy 2000RS Plus - Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operation
Remote Locking
To Lock the doors:
1. Turn off the ignition.
2. Press Button 1.
· The audible status output will beep (if connected)
· The doors will lock.
· The parking lights will flash once.
· The LED will turn on red, to indicate the doors are locked.
3. 10 seconds after Locking:
· The LED will start blinking as a theft deterrent.
Remote Unlocking
To Unlock the doors:
Press Button 1.
· The audible status output will beep (if connected)
· The doors will unlock.
· The parking lights will flash twice.
· The dome light will turn on.
· The LED will turn off.
Optional Panic Mode
In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the
optional horn honk or audible status output, if connected.
To activate the Panic Mode:
1. Press and hold Button 1 for 3 seconds.
· The horn will honk (if connected).
· The parking lights will flash.
· The doors will unlock allowing access to the vehicle.*
2. Press Button 2 to stop Panic Mode.
* If the ignition is on when the Panic feature is activated, the doors will lock for personal safety.
If not deactivated using Button 2, the Panic Mode will automatically exit after 30 seconds and the system
will be restored to its previous Locked/Unlocked state.
Valet Mode
The Valet Mode temporarily disables the remote start system so the vehicle may be serviced by a mechanic.
The remote transmitters will continue to lock/unlock the doors, and operate the optional auxiliary functions.
To activate or deactivate the Valet Mode:
1. Turn on the ignition.
2. Press and hold the override switch for 5 seconds.
· The parking lights will flash once to confirm the Valet Mode is on.
· The parking lights will flash twice to confirm the Valet Mode is off.
3. Turn off the ignition.
Page 6 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Start Features
Remote Starting
To Remote Start the System:
1. Be sure the system is not in Valet Mode.
2. Press and hold Button 4 for three seconds.
· The parking lights will turn on.
· The LED will flash rapidly.
· The engine will start and run for the duration of its programmed Run Time.*
· The heater or air conditioner will turn on (if turned on prior to exiting the vehicle).
*If the engine fails to start on the first attempt, it will repeat the starting procedure 2 more times. If the vehicle
fails to start after a total of 3 times the parking lights will flash 4 times and the doors will lock (if installed).
Turn on the ignition and press the bake pedal to disengage the remote start feature and drive the vehicle.
Shut Down
When the the Remote Start feature is active, any of the following actions will shutdown the engine:
1. Pressing Button 4.
· After the engine shuts down the doors will lock (if installed).
2. Pressing the Brake Pedal.
3. Opening the Hood.
4. Remote Start Time-Out (completion of the timed run cycle).
Quick Stop
The Quick Stop Feature allows you exit the vehicle while keeping the engine running for quick stops.
To leave the vehicle running:
1. While engine running Push Start Button on the Remote Transmitter until the parking lights flash.
· The parking lights will turn on.
2. Remove the key from the ignition switch.
3. You may now exit the vehicle and lock the doors manually or using the Remote Transmitter
To resume control of the vehicle:
1. Unlock the doors manually or by pressing Button 4 on the Remote Transmitter*.
2. Turn on the ignition.
3. Press the Brake Pedal to disengaged the remote start.
*If optional keyless entry feature is installed.
Galaxy 2000RS Plus - Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Start Mode
The Automatic Start Mode allows the vehicle to automatically start the vehicle every one or two hours and
run for the preset Run Time.
To turn on Auto Cold Starting:
1. Turn Ignition switch Off and wait for 3 seconds.
2. Turn Ignition switch On and Off three times ending with Ignition in Off position
3. Press the Valet switch within three seconds
Side lights will flash indicating that the Cold Start mode has been activated.
To turn off Auto Cold Starting do one of the following:
· Turn on the ignition.
· Lock and Unlock using the remote
· Panic the system
Starter Diagnostics
Starter doesn’t start and Side Lights flash:
3 Times -
Engine RPM not detected
Hood Trigger is active
4 Times - Brake Trigger is active
5 Times - Unit is in Valet (service) mode, and start is disabled.
Page 8 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Extended Features
Ignition Door Locking
For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems
to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned
on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle.
Ignition Door Unlocking
For added convenience, this feature automatically unlocks the doors after the ignition key is turned off. If
the optional Passenger Unlock feature is installed, the Ignition Door Unlocking feature can be programmed
to unlock only the driver door as a higher measure of safety, especially when children are present. The
Ignition Door Unlocking feature may also be completely disabled if desired.
Dome Light Activation
If the optional Dome Light Activation feature is installed, the dome light will turn on when the system is
disarmed using the Remote Transmitter, and remain on for 30 seconds or until the ignition is turned on.
Auxiliary Function Outputs
The Galaxy Starter system is equipped with 3 Auxiliary Channel Outputs allowing the convenience features
of the system to be further expanded. These outputs can be programmed for pulsed, timed, or latched
operation, and used to add a number of optional features such as: power trunk release, remote engine start,
power window activation, power sunroof control, auxiliary lighting, audio/video system control, and more.
The Pulsed operation setting allows an output to activate as long as the button is held.
The Timed operation setting allows an output to activate when the transmitter button is pressed, and
remain activated for 10 seconds or until the transmitter button is pressed again.
Note: With the optional ScyNet network interface and Wizard software, the timed output can be programmed for any time
between 1 second and 255 seconds.
The Latched operation setting allows an output to activate when the transmitter button is pressed, and
remain activated until the transmitter button is pressed again.
Turbo Timer Feature
The optional Turbo Timer feature allows vehicles with turbocharged engines to remain running after the
ignition key is removed, for proper cool-down of the turbocharger. The Turbo Timer feature requires
connection to the vehicle’s parking brake wire and is compatible with most gasoline powered engines, and
diesel engines where a glow plug connection is not required.
To activate the Turbo Timer feature:
1. Leave the engine running after parking the vehicle.
2. Set the vehicle’s parking brake.
· The Turbo Timer will begin a two-minute run cycle to allow the turbocharger to cool down.
3. Turn OFF the ignition and exit the vehicle.
To deactivate the Turbo Timer feature:
1. Turn OFF the ignition.
2. Press the brake pedal.
· The Turbo Timer countdown will automatically stop and the engine will shutdown.
WARNING: the Turbo Timer feature is not intended for use inside garages or other non-ventilated areas.
Make sure to deactivate the Turbo Timer feature when parking in such areas.
Galaxy 2000RS Plus - Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
System Installation
1. Thoroughly read and become familiar with the installation instructions before beginning the installation.
2. Review system contents:
Main Unit
Two 5-Button Remote Transmitters
Harnesses
• 6-Pin starter harness
• 20-Pin main harness
• 4-Pin auxiliary start harness
• 3-Pin door lock harness
• LED harness
• Override Switch harness
3. Verify vehicle is equipped with electronic fuel injection, and starts/idles normally before installation.
4. Determine if vehicle is equipped with a factory theft deterrent system and obtain proper bypass module
if required.
5. Find a location to mount the hood pin switch that will not interfere with the opening of the hood, and
is not in a position that can accumulate water. The hood pin is a safety device that must be installed
to avoid remote starting during engine servicing.
6. Verify with the owner, mounting locations for all visible components, including the LED and Valet switch.
7. Verify with the owner, the optional features of the Galaxy Starter and the features that must be
programmed during installation.
8. Inspect and perform a function test of all vehicle systems before and after the installation.
9. Always use a Volt / Ohm meter for testing vehicle circuits. Never use a test light.
10. Always look before drilling any holes or mounting self-tapping screws. Be sure fuel lines and exterior
wiring looms are clear as they are often close to the chassis and difficult to see.
11. Protect all wires running from the engine compartment to the interior of the vehicle by covering with
electrical tape and split loom tubing. Be sure to use a grommet when routing wires through the firewall.
12. Properly fuse any additional accessories such as window modules, door lock actuator, etc., making sure
to power them separate from the alarm module. This will ensure the functionality of the security system
in the event of an accessory failure.
Mounting the Control Unit
The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in
the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and
will not interfere with the operation of any vehicle components such as foot pedals, steering column,
air vents, seat rails, etc.
Do not mount the control unit until after setting the internal jumpers and performing a complete
operation check of the system. After installation is complete and performance verified, the control unit
can be easily mounted using wire ties through the mounting tabs on the bottom of the unit.
Page 10 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
System Wiring
6-Pin Starter Harness
Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition
switch with a minimum 30 Amp supply. Remove fuse until installation is complete and wiring is checked.
Pin 2 RED WIRE B: Main Power Input B (+). Connect to the battery or constant power wire at the ignition
switch with a minimum 30 Amp supply. Note: if connecting at the ignition switch it is highly
recommended to use separate power wires for each Red wire, each with a minimum 30A supply.
Remove the fuse until the installation is completed and all wiring is checked.
Pin 3 BROWN WIRE: Second Ignition Output (+). The Brown wire provides +12V for a second ignition
wire. This wire may instead be programmed for use as a second accessory or second starter wire.
Pin 4 ORANGE WIRE: Accessory Output (+). Connect to the accessory wire coming from the ignition
switch that supplies power to the heater/air-conditioner. Some cars may have multiple accessory wires.
Pin 5 YELLOW WIRE: Ignition Output (+). Connect to the main ignition wire that provides +12V when the
ignition is on and while cranking the starter.
Pin 6 VIOLET WIRE: Starter Output (+). Connect to the the vehicle’s starter wire.
20-Pin Main Harness
Pin 1 GREEN/WHITE WIRE: Brake Input (+). Connect to the wire that shows +12V when pressing the
brake. The Green/white wire is a safety shutdown wire that must be connected.
Pin 2 BLACK/GRAY WIRE: Tach Input. Connect to the vehicle’s tach wire or a fuel injector wire if the
tachless mode does not provide satisfactory operation.
Pin 3 WHITE/RED WIRE: Auxiliary 2 Output (-) 500 mA. Connect to a relay or module for an optional
feature such as power window activation, etc. This output may be programmed for momentary, timed,
or latched operation.
Pin 4 BLACK/WHITE WIRE: Dome Light Output (-) 500 mA. Connect to the wire that activates the
vehicle’s dome light, usually the door pin switch wire. NOTE: The dome light output can usually connect
to the same wire used for the door trigger input (see Green and Violet door trigger wires).
Pin 5 YELLOW WIRE: +12V Ignition Input. The Yellow wire must connect to a main ignition wire at the
ignition harness. This wire must show +12V when the ignition is on and while cranking the starter. The
voltage must not drop when the car is starting.
Pin 6 BLUE/YELLOW WIRE: Glow Plug Input (+). For vehicles equipped with diesel engines the
Blue/yellow wire must be connected to the wait-to-start light in the gauge panel. This wire will show
+12V when the light is on, and ground when the light turns off. If the wait-to-start wire shows ground
when the light is on, a relay must be installed (see wiring diagrams).
Pin 7 BLUE/WHITE WIRE: Passenger Unlock Output (-) 500 mA. Connect to a relay to unlock the
passenger doors when the system is configured for Driver Priority Unlocking.
Pin 8 BLUE/ORANGE WIRE: Ground When Running Output (-) 500 mA. Connect to an optional factory
security bypass module if required, also conntect to activate a relay for anti-grind protection.
Pin 9 BLACK WIRE: Ground Input (-). The Black wire must connect to a solid chassis ground. Clean away
any paint or dirt to insure the best possible ground.
Pin 10 RED WIRE: Module Power Input (+). Connect to a constant source of +12V.
Pin 11 VIOLET WIRE: Positive Door Input (+). Connect to the door switch circuit wire that shows +12V
when the door is open. This type of door circuit is usually found on Ford vehicles.
Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch circuit wire that shows ground
when the door is open.
Galaxy 2000RS Plus - Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Pin 13 WHITE/BLACK WIRE: Hood Pin Input (-). Connect the to the hood pin switch. The switch must
provide a ground output when switch is opened.
Pin 14 ORANGE WIRE: Starter Interrupt Output (-) 500 mA. The wire provides a ground output when doors
are locked with remote control.
Pin 15 VIOLET/WHITE WIRE: Factory Disarm Output (-) 500 mA. The Violet/white wire provides a ground
output on disarming and before remote starting to disarm a factory security system. Connect to the
wire that requires a ground pulse to disarm the factory security system.
Pin 16 WHITE/VIOLET WIRE: Factory Rearm Output (-) 500 mA. The White/violet wire provides a ground
output on remote start shutdown to rearm a factory security system. Connect to the wire that requires
a ground pulse to rearm the factory security system.
Pin 17 BROWN WIRE: Audible Status Output (+) 3A. The Brown wire may be connected to an optional
audible status indicator such as a siren or piezo device.
Pin 18 GRAY WIRE: Auxiliary 1 Output (-) 500 mA. Connect to a relay for an optional feature such as trunk
release, etc. This output may be programmed for momentary, timed, or latched operation.
Pin 19 WHITE WIRE: Parking Light Output (+/-) relay. Connect the White wire to the circuit that shows
+12V or ground only when the parking lights are on and set the internal parking light relay jumper to
the proper polarity. For parking light circuits exceeding 10 amps, a relay is required. For vehicle’s with
independent left and right parking light circuits, diode must be installed to keep the circuits separate.
NOTE: Do not connect the WHITE wire to the vehicle’s headlight circuit.
Pin 20 BROWN/WHITE WIRE: Horn Output (-) 500 mA. Connect to a relay to honk the vehicle’s horn when
the panic feature is triggered. This wire may instead be programmed as an ignition 3 relay trigger.
Plug-in Connectors
4-Pin White Connector: Auxiliary start input port for use with after-market security system.
· WHITE WIRE - 3 pulse remote start / Parking Brake (-) input.
3 Pulse Remote Start Input: Connect to the door lock output from the keyless entry system. When the
lock button is pressed 3 times the vehicle will start.
Parking Brake Input: For vehicles equipped with a turbo charged engine, this wire must be connected to
the parking brake wire if using the optional Turbo Timer feature. For vehicles with a positive parking brake
wire, a relay must be used to invert the polarity.
· BLUE WIRE - 1 pulse remote start (-) input. Connect to auxiliary output from aftermarket alarm.
· RED WIRE - not used.
· BLACK WIRE - not used.
2-Pin Blue Connector: Valet switch port. Mount switch where it is accessible from the driver’s position.
2-Pin Red Connector: LED port. Mount LED where it may be easily seen from either side of the vehicle.
3-Pin White Door Lock Connector: Door lock port.
· BLUE WIRE - negative unlock output (-) 500mA.
· RED WIRE - (+) 100mA trigger output for optional plug-in door lock relay module,
· GREEN WIRE - negative lock output (-) 500mA.
3-Pin Blue Network Connector: The plug-in network connector port is located on the side of the main
module. This network port may be used with the optional personal computer interface or Pocket PC for
diagnostics, software customization and expanded programming options. The network also offers
connection to several optional accessories. See your dealer for more information.
4-Pin White Flat Connector: Antenna connector port.
Page 12 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Jumper Settings
Jumper Selection
Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parking
light polarity jumper will be visible next to the parking light relay. Set the jumper for the correct polarity
output as described below, then reassembly the main unit case.
Parking Light Output. Selects the polarity (+/-) for the output of the on-board Parking Light relay.
Left Pin + Center Pin = positive
Right Pin + Center Pin = negative
default setting shown
Galaxy 2000RS Plus - Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
System Programming
Entering System Programming
Although this system is compatible with the optional FM transmitter, all programming is performed using
the standard AM transmitter unless otherwise noted.
To enter System Programming:
1. Turn on ignition.
2. Within 5 seconds, press the valet switch 5 times.
· The parking lights will provide three blinks, indicating that you have entered Programming.
3. Press the valet switch the number times equal to the System Parameter you want to change.
· The parking lights will flash each time the valet switch is pressed.
4. Within 5 seconds, press the transmitter button corresponding to the desired operating mode for
that System Parameter.
· The parking lights will flash to indicate the setting.
1 flash
=
=
=
Button 1
Button 2
Button 3
2 flashes
3 flashes
5. When you are finished, turn off the ignition to save the changes.
Default Reset
Following this procedure will set all System Programming Parameters to factory default settings.
1. Enter System Programming.
2. Press Transmitter Button 3.
· The parking lights will flash 6 times indicating that the reset signal was received.
· All System Programming parameters are now set to factory default settings.
· The Valet Mode is off.
3. Turn off ignition.
Programmable System Options
The following is a description of the programming options of the system. Some of the program branches
control more than one option, and may require accessing a particular branch number twice in order to
program all desired features.
1. Ignition Door Locking. Selects whether or not the system will automatically lock the doors 5 seconds
after the ignition key is turned on.
2. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors when
the ignition is turned off. The Ignition Door Locking feature may be programmed to unlock all doors or
the driver’s door only. If driver’s door only is selected, the optional Passenger Unlock wire must be
connected. (See Two Stage Door Lock Diagrams)
3. Door Unlock Pulse. Selects between one pulse or two pulse operation for the door unlock output.
Many new import vehicles’ factory door locking systems require two pulses on the proper wire to unlock
the doors. These systems can be interfaced directly without the use of relays or any additional circuitry
by programming the system for double unlock pulse.
Page 14 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Branch Feature
Button 1 (default)
Button 2
Off
Button 3
1. Ignition Door Locking
2. Ignition Door Unlocking
3. Door Unlock Pulse
4. Door Lock Pulse Length
5. Aux 2 Activate on Lock
6. Aux 1 Mode
On
Unlock All
Single
1 second
Off
Unlock Driver Only
Double
Off
3 seconds
On
Pulsed
Pulsed
Timed
Latched
Latched
7. Aux 2 Mode
Timed
8. not used
9. Start in Valet Mode
10. Lock after Start
Disable
Enabled
On
Off
11. Lock after Shutdown
12. Engine Run Time
13. Automatic Start Mode
14. Engine Sense Mode
15. Remote Start Program
16. FM Transmitter Program
17. Ignition 2 Output Program
18. Horn Honk Output
19. Turbo Mode
On
Off
15 minutes
2 hours
25 minutes
1 hour
Tachless
RPM Learn
not used
Ignition 2 Output
Horn Output
Disabled
Tach Monitor
Gas Engine
FM Remote Learn
Diesel Engine
Accessory 2 Output Starter 2 Output
Ignition 3 Output
Enabled
4. Door Lock Pulse Length. Selects between a 1-second and a 3-second output for door locking and
unlocking. Program to 3 seconds for vehicles equipped with vacuum door locking systems.
5. Aux 2 Auto Activate with Arm. When selected, the Auxiliary 2 output will activate when the system
is armed. This feature can be used to roll-up windows, close sunroofs, activate accessories, etc.
6. Auxiliary 1 Mode. Selects from momentary, 10 second timed, or latched operation for Auxiliary 1.
Momentary operation provides an output for as long as the transmitter button is pressed.
Timed operation provides an output that turns on for 10 seconds each time the transmitter button is
pressed. If the button is pressed again during the 30 seconds, the output will turn off.
Latched operation provides an output that turns on when the transmitter button is pressed and remains
on until the transmitter button is pressed again.
Note: With the optional ScyNet network interface and Wizard software, any auxiliary function can be
programmed to output for 1 second up to 255 seconds.
7. Auxiliary 2 Mode. Selects from Momentary, Timed, or Latched operation for Auxiliary 2.
8. Disarm with Auxiliary 1. When selected, activating the Auxiliary 1 output (usually used to open the
trunk) will disarm the alarm.
9. Start in Valet Mode. Selects whether or not the vehicle can remote start while in the valet mode.
10. Lock After Start. When selected, the doors will automatically lock after remote starting.
11. Lock After Shutdown. When selected, the doors will automatically lock after remote shutdown.
12. Engine Run Time. Selects between 15 or 25 minutes for the remote start run cycle.
13. Automatic Start Mode. Selects between every two hours or every hour for the automatic engine
starting feature.
Galaxy 2000RS Plus - Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Engine Sense Mode. Selects between Tachless and Tach Monitor operation.
Tachless. Determines the engine status using an advanced software routine, without requiring
connection to the vehicle’s tachometer. Tachless operation may not be compatible with some vehicles
or in severe temperatures, in which case the tach wire must be connected.
Tach Monitor. Monitors the vehicle’s tach wire (or a fuel injection wire) in real-time to determine engine
status and adjust starter crank time automatically. If programmed for Tach Monitor, the vehicle’s tach
signal will have to be learned before initial operation (see below).
15. Remote Start Program. This dual program branch sets the engine mode for Gas or Diesel, and
learns the vehicle’s RPM threshold. For installation into a diesel equipped vehicle, first set the engine
type to diesel before learning RPM.
RPM Learn. After engine type is set, start the engine, re-enter Branch 15, LED will start flashing if tach
signal is detected, otherwise the LED will stay solid. Press Button 1 to learn the vehicle’s idle speed.
The siren will chirp once to confirm. The siren will chirp four times if the tach signal was not learned.
Gas Engine. Sets the engine type for Gasoline.
Diesel Engine. Sets the engine type for Diesel and monitors the glow plug input to make sure the glow
plugs are warm before cranking the starter. If the glow plug wire is not connected, the built-in timer
waits 15 seconds before automatically cranking the starter.
16. FM Transmitter Program.* Programs the optional FM module and transmitter into the system.
FM Module Learn. Learns the add-on FM module ID so the FM transmitter can operate the system. The
FM module must be connected before completing this step.
FM Remote Learn. Learns the optional 2-way FM transmitter. Press Button 2 on the 1-way remote to
enter FM Transmitter learn mode, then press transmitter Button 1 on each FM remote (max 2).
*Requires the optional ScyNet FM LCD Pager Module.
17. Ignition 2 Relay Program. Selects one of three operating modes for the Ignition 2 relay output:
Ignition 2, Accessory 2, or Starter 2.
18. Horn Output. When set for Horn Output the horn wire will pulse when the alarm is triggered. When
Ignition 3 Output is selected, the output will activate during remote start to trigger a relay for Ignition 3.
19. Turbo Timer. When enabled, if the emergency brake has been applied Ignition power will be kept On
for a predetermined time (2min. Factory Default) from the application of the emergency brake.
Page 16 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagrams
Positive Dome
Negative Dome
TO POSITIVE
DOME LIGHT
TO NEGATIVE
DOME LIGHT
Black/White
(-) DOME LIGHT
OUTPUT
Black/White
(-) DOME LIGHT
OUTPUT
+12V
+12V
Positive Horn
Negative Horn
TO POSITIVE
HORN WIRE
TO NEGATIVE
HORN WIRE
Brown/White
(-) HORN OUTPUT
Brown/White
(-) HORN OUTPUT
+12V
+12V
Negative Glow Plug
Starter Anti-Grind
+12V
Yellow Wire
(+) IGNITION
Orange wire
(-) ANTIGRIND
(-) GLOW PLUG
WIRE FROM
VEHICLE
Yellow Wire
(+) IGNITION
Violet Wire
(+) STARTER
T
L
C
TO STARTER
Blue/Yellow Wire
(+) GLOW PLUG
INPUT
IGNITION SWITCH
Galaxy 2000RS Plus - Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Door Lock Diagrams
Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock
systems (separately unlocks driver and passenger doors) see following pages.
Negative Trigger
Positive Trigger
Reverse Polarity
Vacuum
Adding Actuator
Page 18 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Two Stage Door Lock Diagrams
The Galaxy Starter is equipped with a dedicated Passenger Unlock output allowing Two Stage
Door Lock operation. When connected as shown below, unlocking the system will unlock only
the driver’s door. Pressing the unlock button again will unlock all doors.
Two Stage Negative Trigger
Two Stage Positive Trigger
Galaxy 2000RS Plus - Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Two Stage Door Lock Diagrams cont’d
Two Stage Reverse Polarity
Two Stage Adding Actuator
Page 20 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Galaxy 2000RS Plus - Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 22 - Galaxy 2000RS Plus
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
FCC ID: OARRXAM2000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation
Galaxy 2000RS Plus - Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
ScyTek Electronics
11627 Cantara Street Unit B
North Hollywood, CA 91605
© ScyTek Electronics 2003
Galaxy Starter r5 2/18/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|