RCA Camcorder CC632 User Guide

CC4 2 3  
USER‘S  
GUIDE  
C A M C O R D E R  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Information  
Be sure to read all the safety information before you begin to use this product.  
WARNING: To reduce the risk of fire or shock hazard, do not expose  
camcorder or AC adapter/charger to rain or moisture.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
This symbol indicates Òdangerous voltageÓ  
inside the product that presents a risk of  
electric shock or personal injury.  
ATTENTION  
This symbol indicates important  
RISQUE DE CHOC  
ELECTRIQUE NE PAS OUVRIR  
instructions accompanying the product.  
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE  
COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
CAUTION: To prevent electric shock, match wide blade of plug  
to wide slot, fully insert.  
ATTENTION: Pour éviter les chocs électriques, introduire la lame  
la plus large de la fiche dans la borne correspondante de la prise et  
pousser jusqu au fond.  
To reduce risk of injury, charge only rechargeable batteries recommended by the  
manufacturer for this camcorder. Other types of batteries may burst causing  
damage and personal injury.  
CAUTION: Avoid operating your camcorder immediately after moving it from  
a cold location to a warm location. Give the camcorder 2 to 3 hours to reach a  
stable temperature before inserting a video cassette. When moved from a cold  
area to a warm location, moisture may condense on the head drum inside the  
machine. This moisture could cause the tape to stick to the headwheel and  
damage the headwheel or tape.  
FCC Regulations state that unauthorized changes or modifications to this  
equipment may void the user’s authority to operate it.  
Product Registration  
Please fill out the product registration card and return it immediately. Returning  
this card allows us to contact you if needed.  
Keep your sales receipt for proof of purchase to obtain warranty parts and service  
and attach it here. Record the serial and model numbers located on the bottom of  
the camcorder.  
CC423  
Model _______________________________________________________  
Serial No:_____________________________________________________  
Purchase Date: ________________________________________________  
Purchased From: ______________________________________________  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assistance  
We want to make sure you enjoy your new camcorder. If you have any  
questions, call:  
Camcorder Exchange Warranty...... 800-283-6503 (Pages 66-67)  
Customer Service..................................... 800-336-1900 (Page 65)  
Accessories......................................... 800-338-0376 (Pages 52-59)  
Table of Contents  
Safety Information................................i  
Product Registration.............................i  
Contents.............................................1-2  
Powering the Camcorder  
• Using the Adapter/Charger ...............10  
• Using the Rechargeable Battery  
• Charging.........................................11  
• Attaching and Removing................12  
• Care and Storage ............................13  
• Safety Precautions..........................13  
• Battery Level Indicator...................14  
• Using the Optional Car Cord  
First-Time Operation  
• Assistance............................................3  
• Unpack Camcorder and  
Accessories ......................................3  
• Attach the Adapter/Charger ................4  
• Remove Lens Cap and Attach  
to Handstrap.....................................5  
• Turn on the Camcorder .......................5  
• Insert a Cassette ..................................6  
• Position Viewfinder and  
Adapter.........................................15  
Video Cassettes  
• Erase Protection..............................16  
• Recording and Playback Times......16  
• Inserting and Removing  
Cassettes.....................................17  
Cassette Care and Storage................17  
Adjust Eyepiece Focus Control .......6  
• Start and Stop Recording ....................7  
• Play Back What You Have  
Recorded ..........................................7  
• Review the Camcorder’s  
Traveling Tips ....................................18  
Cassette Tips.......................................18  
Operating Controls .......................8-9  
(continued on next page)  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Recording Features  
Playback  
• Quick Review....................................19  
• Tape Positioning ...............................19  
• Microphone .......................................19  
• AI (Artificial Intelligence) ................19  
• Program AE (Auto Exposure)...........20  
• Auto Focus ........................................20  
• Macro Focus......................................20  
• Electronic Indexing...........................21  
• Time Remaining Display ..................21  
• Viewfinder ...................................22-23  
• Displays in Viewfinder................24-25  
• Date and Time Display  
• Viewfinder Playback.........................42  
• Playback Features  
• Stop-Action Pause.....................42-43  
• Picture Search ...........................42-43  
• Tracking .........................................43  
• Playback on TV (or VCR) with  
AUDIO/VIDEO IN Jacks.......44-45  
• Playback on TV without  
Audio and Video Inputs.........46-47  
Color Enhancement Light............48-49  
Attaching the Shoulder Strap ...........50  
Packing the Carrying Case ...............51  
• Set the Date and Time ....................26  
• Record the Date and Time  
(or Date) on Your Tape .............27  
Optional Accessories.....................52-59  
• Accessory Order Form.................57-59  
• Charging the Clock Cell.................27  
• Zooming............................................28  
• Fading In and Out of Scenes.............29  
• Tape Counter with Memory Stop......30  
Care and Maintenance.................60-61  
Trouble Checks.............................62-64  
Assistance............................................65  
Limited Warranty.........................66-67  
Specifications......................................68  
User Information................................69  
Index (Alphabetical).....................70-73  
®
• ProEdit Features  
• Flying Erase Head ..........................31  
• Edit Search .....................................31  
• Audio Dubbing..........................32-33  
• Audio/Video Dubbing...............34-35  
• Titler..........................................36-38  
Recording Tips ...................................39  
Recording on the Camcorder ......40-41  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Time Operation  
This section describes only the basic steps necessary to set up your camcorder to  
record. Refer to the other sections for detailed operation and feature options.  
Assistance  
The toll-free numbers are available to help you with any problem you may encounter.  
Camcorder Exchange Warranty . . . . .800-283-6503  
Customer Service . . . . . . . . . . . . . . . .800-336-1900  
Accessories . . . . . . . . . . . . . . . . . . . .800-338-0376  
1. Unpack the camcorder and accessories.  
• Save the box and packing materials in case you ever need to store or ship  
your camcorder.  
• The items shown below are packed with your camcorder. If any of them are  
missing or appear damaged, contact your dealer immediately.  
S
T
O
P
/E  
J
E
C
T
F.  
F
W
D
E
D
IT –  
A
D
V
P
L
A
Y
+
R
E
W
TITLE S  
E
L
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
Camcorder  
Model CC423  
Carrying Case  
Part No. 221286  
WARNING: LEAD-ACID BATTERY.  
MUST BE DISPOSED OF PROPERLY.  
Rechargeable 10-Volt Battery  
Stock No. EP096FS  
Shoulder Strap  
Stock No. 227327  
Caution: Do not use this  
adapter/charger for any purpose  
other than charging the EP096FL or  
EP096FS battery pack or supplying  
power to the camcorder.  
AC Adapter/Charger:  
Stock No. 221355 or 221356  
DC Cable: Stock No. 209342  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Time Operation  
Adapter/  
Charger  
BATTERY  
DC OUTPUT  
Jack  
Adapter/Charger’s  
DC Cable  
DC IN 9.6V Jack on  
Back of Camcorder  
2. Attach the adapter/charger.  
• Attach the other end of the cable to  
the DC IN 9.6V jack on the  
camcorder.  
Since the battery must be charged  
before it can be used the first time,  
attach the adapter/charger to the  
camcorder.  
• Plug the adapter/charger’s plug into  
an operating outlet.  
• Attach one end of the  
adapter/charger’s DC cable to the  
DC OUTPUT jack on the  
adapter/charger.  
Details are on page 10.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Time Operation  
POWER (CAMERA/OFF/VCR)  
Switch and Indicator  
STOP/EJE  
C
T
EDIT – ADV  
F.FWD  
+
PLAY  
TITLE SE  
REW  
L
AV DUB  
VCR  
O
F
F
O
WE  
R
Handstrap  
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
Lens Cap  
• Press and hold the small button on  
POWER while sliding it in  
CAMERA. The POWER indicator  
will light when the camcorder is  
turned on.  
3. Remove the lens cap and attach  
it to the handstrap.  
4. Turn on the camcorder.  
The position of the POWER  
(CAMERA/OFF/VCR) switch tells  
the camcorder whether you want to  
record (CAMERA), play back tapes  
(VCR), or turn off the power (OFF).  
(continued on next page)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Time Operation  
Safety Tab  
Tape Window  
BATTERY  
REC (Record)  
/PAUSE  
Button  
Lens Cap on  
Handstrap  
Cassette Door  
Press Here to Close  
6. Position viewfinder and adjust  
eyepiece focus control.  
• Grasp the viewfinder and rotate it  
horizontally.  
5. Insert a cassette.  
• Press STOP/EJECT to open the  
cassette compartment.  
• Insert the cassette with the safety tab  
facing up and the tape windows  
facing out.  
• Pull the viewfinder out from the  
camcorder and rotate the eyepiece  
into a comfortable viewing position.  
• Press the cassette down gently until  
it locks into place, and close the  
cassette compartment door.  
Caution: Pulling on the eyepiece may  
cause damage to the eyepiece or  
camcorder.  
Details are on page 17.  
• If the image in the viewfinder is  
blurry, adjust the eyepiece focus  
control for your vision. Details are  
on page 22.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Time Operation  
POWER (CAMERA/OFF/VCR)  
Switch and Indicator  
REW (Rewind)  
PLAY  
STOP/EJECT  
STOP/EJE  
C
T
EDIT – ADV  
F.FWD  
+
PLAY  
TITLE SE  
REW  
L
AV DUB  
VCR  
O
F
F
O
WE  
R
REC (Record)  
/PAUSE  
Eyepiece  
Focus  
R E C / P A U S E  
T R A C K I N G  
Control  
Eyepiece  
FADE  
Electronic  
Viewfinder  
(Grasp Here  
to Move)  
ON  
LIGHT  
OFF  
AUTO  
8. Play back what you have  
recorded.  
• Press REC/PAUSE to stop recording.  
7. Start and stop recording.  
Start and stop recording by pressing  
and releasing REC/PAUSE. REC  
appears in the viewfinder. You do not  
have to hold the button to record.  
• Press and hold the small button on  
POWER while sliding it in VCR.  
Notes: If you do not record within five  
minutes, the camcorder will automatically  
shut off to prevent excessive tape wear.  
Press REC/PAUSE to turn on the  
camcorder.  
• Press REW (rewind) to rewind the  
tape.  
• Press PLAY to play back the tape in  
the viewfinder.  
Any material recorded on the tape will  
automatically be erased if you record  
over it.  
• Press STOP/EJECT when you are  
finished playing back the tape.  
• Details on viewfinder playback are  
on page 42.  
(continued on next page)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Time Operation  
9. Review the camcorder’s operating controls.  
REVIEW Button  
DISPLAY Button  
RESET Button  
AV DUB Button  
REW (Rewind) Button  
Also TITLE SEL – Button  
PLAY Button  
Also TITLE SEL Button  
DATE/TIME Button  
TITLER Button  
F.FWD (Fast Forward) Button  
Also TITLE SEL + Button  
REVIEW DISPLAY RESET DATE  
/TIME  
TITLER  
CAMERA OFF  
POWER  
VCR  
AV DUB  
REW  
PLAY  
F.FWD  
+
STOP/EJECT  
EDIT – ADV  
TITLE SEL  
STOP/EJECT Button  
Also EDIT–ADV Button  
POWER  
(CAMERA/OFF/VCR) Switch  
and Indicator  
Viewfinder  
Microphone  
Light  
S
E
T
O
P/EJE  
D
C
V
T
DIT – A  
F.FWD  
+
P
LA  
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
OW  
F
F
E
R
Eyepiece  
Focus  
Control  
BRIGHT Control  
(Located Under Microphone)  
R E C / P A U S E  
T R A C K I N G  
Lens  
FADE  
AV (Audio/Video)  
OUT/IN Switch  
ON  
LIGHT  
AUTO  
OFF  
LIGHT AUTO/OFF/ON  
Switch  
Lens  
Hood  
AV  
OUT  
/
IN  
FADE Button  
VIDEO, AUDIO, and RF DC OUT  
Jacks (Located Behind Small Cover)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Time Operation  
9. Review the camcorder’s operating controls.  
Shoulder Strap  
Attachment  
Ring  
Shoulder Strap  
Attachment  
Ring  
TINT  
C
O
LO  
R
COLOR and  
TINT Controls  
BATTERY  
Eject Lever  
Power Zoom Buttons  
(W and T) also TRACKING  
Buttons  
BATTERY  
REC (Record)  
/PAUSE Button  
DC IN  
9.5V  
DC IN 9.6V Jack  
Hand Strap with  
Lens Cap Holder  
Cassette Door  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering the Camcorder  
Caution: Do not attempt to use a “power converter” to use your AC adapter/charger  
on a power source other than 120 volts, 50/60 Hz, or the adapter/charger and  
camcorder may be damaged. If you wish to operate the AC adapter/charger on a  
power source other than 120 volts, 50/60 Hz, use only a transformer-type power  
converter. Do not use “solid-state” or “switching-type” power converters. They  
will damage your AC adapter/charger. An optional CPS014 shown on page 53 is  
designed for use on 100-240 volts, 50/60 Hz.  
Using the Adapter/Charger to Power Your Camcorder  
Plug in AC Outlet  
(120V, 50/60Hz)  
Adapter/Charger  
BATTERY  
POWER  
Indicator  
DC  
OUTPUT  
Jack  
Adapter/Charger’s  
DC Cable  
DC IN 9.6V Jack  
When using the adapter/charger to power  
the camcorder, the battery level indicator  
may display . This indicator is used  
for battery operation and has no meaning  
when using the adapter/charger to power  
the camcorder.  
1. Connect one end of the adapter/  
charger’s cable to the adapter/  
charger’s DC OUTPUT jack and the  
other end to the DC IN 9.6V jack on  
the back of the camcorder.  
2. Plug the adapter/charger into the  
nearest AC outlet (120V, 50/60 Hz).  
To Remove the Adapter/Charger  
1. Remove the adapter/charger’s plug  
from the AC outlet.  
3. The POWER indicator on the  
adapter/charger will light when it is  
properly connected.  
2. Remove the adapter/charger’s DC  
cable from the DC IN 9.6V jack on the  
camcorder.  
Notes: The adapter/charger cannot charge  
the battery and operate the camcorder at the  
same time. If you connect both, the  
adapter/charger will power the camcorder.  
Remove the adapter/charger’s cable from  
the DC OUTPUT jack to charge the  
battery.  
Caution: Do not use this adapter/charger  
for any purpose other than charging the  
EP096FS, EP096FL, CB096FS, or CB096FL  
battery pack or supplying power to the  
camcorder.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering the Camcorder  
Using the Battery to Power Your Camcorder  
Charging the Battery  
The battery must be charged before it can be used the first time. Charging will take  
approximately two hours depending on the condition of the battery. When fully  
charged, the battery should supply approximately 60 minutes of operating time  
(depending on how much you use zoom and pause). To extend the battery’s operation  
time, turn off the camcorder’s power when not in use.  
WARNING: LEAD-  
Hold Battery  
ACID BATTERY.  
Flush and  
Rechargeable  
Battery  
MUST BE DISPOSED  
OF PROPERLY.  
Slide Down  
Align Arrows  
Adapter/Charger  
CHARGE  
Indicator  
Caution: When a  
battery is attached to  
the adapter/charger,  
do not turn them  
upside down. The  
battery may fall off  
and be damaged or  
cause injury.  
Plug in AC Outlet  
(120 V, 50/60 Hz)  
1. Attach the battery to the adapter/  
charger as shown. Align the reference  
arrow on the battery with the arrow on  
the adapter/charger. Hold the battery  
flush against the adapter/charger and  
slide it in the direction of the arrow.  
3. The CHARGE indicator will light  
while the battery is being charged.  
When the indicator turns off, the  
battery is fully charged.  
4. Remove the battery from the  
adapter/charger by sliding the battery  
up and off.  
Note: You cannot charge the battery and  
operate the camcorder from the adapter/  
charger at the same time. Remove the  
adapter/charger’s DC cable from the  
camcorder to charge the battery.  
5. Attach the charged battery to the  
camcorder as shown on the next page.  
2. Plug the adapter/charger into the  
nearest AC outlet (120 V, 50/60 Hz).  
(continued on next page)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering the Camcorder  
Using the Battery to Power Your Camcorder  
POWER Switch  
and Indicator  
BATTERY  
Eject Switch  
Rechargeable  
BATTERY  
Battery  
Hold Battery  
Flush and  
Slide Down  
Align Arrows  
Remove the Battery  
Attach Charged Battery  
1. Slide POWER to OFF. POWER  
indicator will turn off.  
1. Align reference arrow on battery with  
arrow on camcorder. Hold battery  
flush against camcorder while sliding  
it down in the direction of the arrow as  
shown.  
2. Press and hold BATTERY eject while  
sliding battery up and off the  
camcorder.  
2. Press and hold small button on  
POWER while placing it in CAMERA.  
POWER indicator will light if battery  
is properly attached.  
ATTENTION: LEAD-ACID BATTERY MUST BE DISPOSED  
OF PROPERLY. THE PRODUCT THAT YOU HAVE PURCHASED  
USES A RECHARGEABLE BATTERY. AT THE END OF ITS  
USEFUL LIFE, UNDER VARIOUS STATE AND LOCAL LAWS, IT  
MAY BE ILLEGAL TO DISPOSE OF THIS BATTERY INTO THE  
MUNICIPAL WASTE STREAM. CHECK WITH YOUR LOCAL  
SOLID WASTE OFFICIALS FOR DETAILS IN YOUR AREA FOR  
RECYCLING OPTIONS OR PROPER DISPOSAL.  
Pb  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering the Camcorder  
Using the Battery to Power Your Camcorder  
Battery Care  
damaged if operated at temperatures  
• Your battery will provide better service  
and longer performance if you charge it  
before and after use, and store it at  
normal room temperature.  
above 122ºF (50ºC). Operation time  
will decrease at extremely low  
temperatures.  
• After repeated chargings and use, the  
operation time will gradually decrease.  
When operation time becomes too short  
to be useful, it is time to replace the  
battery.  
• The battery should be charged at a  
temperature of 32ºF-95ºF (0ºC-35ºC) to  
prevent damage.  
• Do not operate the battery at  
temperatures below 14ºF (-10ºC) or  
above 95ºF (35ºC). The battery may be  
Battery Storage  
Store the battery at normal room  
temperature.  
• A battery stored for a long period may  
not supply power for the specified time.  
Additional rechargings may help  
• Lead acid batteries discharge if not  
used. Recharge the battery at least once  
every six months or you may not be  
able to recharge it.  
restore the battery’s operation time.  
Battery Safety Precautions  
Batteries being recharged that have not  
been used for an extended period may  
continue to charge after the normal  
time. Do not charge a battery for more  
than 24 hours.  
Allow battery to cool down before  
attaching it to adapter/charger. The  
CHARGE indicator will not light and  
the battery will not charge if you attach  
a hot battery.  
If both indicators on the adapter/  
charger start flashing, remove the  
battery, and reattach it. If after several  
attempts — the indicators continue to  
flash — your battery cannot take a  
charge and must be replaced.  
Do not attempt to disassemble or  
modify the battery. There are no user-  
serviceable parts inside.  
Use the battery only with specified AC  
adapter/chargers and camcorders.  
If leakage from a damaged battery  
contacts your skin or clothing, wash it  
off immediately with running water.  
Throwing the battery into a fire or  
exposing the battery to excessive heat –  
over 149º F (65º C) could be hazardous.  
Do not short the battery’s terminals.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering the Camcorder  
Check Battery Power (Battery Level Indicator)  
Battery Level Indicator  
Display in Viewfinder  
The battery level indicator (  
)
• When the battery reaches the empty  
level, will start flashing.  
Recharge the battery or attach the  
adapter/charger before continuing to  
use the camcorder.  
always appears in the camcorder’s  
viewfinder to show how much battery  
power is left in the rechargeable battery.  
This indicator is not recorded on the tape.  
• When the battery is fully charged, the  
Note: The battery level indicator has no  
meaning when you power the camcorder with  
the adapter/charger or optional car cord.  
display shows  
.
• After a while, only  
appears.  
Caution: When the battery reaches its empty level during use, the camcorder will  
turn off. However, the battery should have enough reserve power to eject the cassette  
when you press STOP/EJECT.  
If the camcorder does not eject the cassette when you press STOP/EJECT, do not  
force the cassette door open. This will damage your camcorder.  
Before attempting to eject the cassette, power your camcorder with the  
adapter/charger or recharge the battery.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering the Camcorder  
Using the Optional Thomson Car Cord Adapter  
To power your camcorder from the cigarette lighter socket of a car, truck, or RV, you  
need the optional car cord adapter DCC096 shown on page 53.  
The DCC096 car cord is especially designed to convert power from a 12-volt battery to  
the 9.6-volt input jack on the camcorder.  
Caution: The DCC096 car cord is designed to be used only with vehicles having  
12-volt negative ground electrical systems.  
Warning: To avoid possible damage to your camcorder, use only the DCC096.  
It has positive tip polarity and is capable of converting 12-volts to 9.6 volts.  
Cigarette Lighter Socket  
BATTERY  
DC  
IN  
9.5V  
DC IN 9.6V Jack  
Optional Car Cord  
Adapter (DCC096)  
Notes: The vehicle does not have to be  
turned on for the camcorder to operate from  
the DC car cord.  
1. Remove the adapter/charger’s DC  
cable or battery from the camcorder, if  
either is attached.  
When using the car cord to power the  
camcorder, the battery level indicator may  
2. Connect the small plug on the car cord  
to the DC IN 9.6V jack located on the  
back of the camcorder.  
display  
. This indicator is used for  
battery operation and has no meaning when  
using the car cord to power the camcorder.  
3. Insert the other end of the car cord into  
the vehicle’s cigarette lighter socket.  
4. Place the camcorder’s POWER switch  
in CAMERA. If the car cord is  
connected properly, the POWER  
indicator will light.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Cassettes  
We recommend that our cassettes be used with your camcorder. Use of poor quality  
tapes or tapes that have been damaged or mishandled can contaminate the video heads,  
resulting in a snowy picture or no picture at all during playback. Because there is no  
control over the type of tape purchased or rented by consumers, head cleaning is not  
covered under warranty. It is considered normal maintenance.  
If a snowy picture or no-picture condition persists, consider the use of a dry chemical  
non-abrasive head-cleaning tape. Be sure to follow the directions with the head-  
cleaning kit carefully. Improper use of a head cleaner may damage your camcorder.  
Erase Protection — Safety Tab  
You can use your video cassettes over and over again. To erase a previous recording,  
just record over it.  
Safety Tab  
To prevent accidental  
erasure, break the tab.  
To record again, cover  
the hole with vinyl tape.  
Recording and Playback Times  
The camcorder records and plays back in VHS standard speed (SP). The chart shows  
the maximum SP recording times for popular VHS cassettes.  
CASSETTE RECORDING TIME  
T-60  
T-120  
T-160  
T-180  
60 Min.  
2 Hrs.  
2 Hrs., 40 Min.  
3 Hrs.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Cassettes  
Inserting and Removing Cassettes  
Safety Tab  
STOP/EJECT  
Caution: Insert  
cassette with  
safety tab facing  
up and tape  
BATTERY  
windows facing  
out. Cassette  
should slide  
easily into the  
compartment.  
Gently push the  
cassette down  
until it locks  
into place.  
Tape Windows  
Press Here to Close  
3. Insert or remove the cassette from the  
cassette compartment.  
1. Attach a power source to the  
camcorder (either a charged battery or  
adapter/charger).  
4. Gently close the cassette door with  
your hand.  
2. Press STOP/EJECT on the top of the  
camcorder to open cassette door.  
Cassette Care and Storage  
Follow these directions for continued high-quality performance from your cassettes.  
• When you are finished with a cassette,  
rewind it and remove it from the  
camcorder.  
• Keep cassettes away from strong  
magnetic fields, such as electric motors  
and other devices.  
• Label and store cassettes vertically in  
their protective cases at normal room  
temperatures. Excessive heat or cold  
may damage your cassettes.  
• Do not use a cassette if it has been  
damaged or exposed to moisture. The  
tape may jam or damage the camcorder.  
• When you are finished recording, break  
off the safety tab on the cassette to  
prevent accidental erasure.  
• Keep dust from entering the cassette  
compartment. All dust is abrasive and  
will cause excessive wear on the tape  
and the camcorder’s recording or  
playback heads.  
• Do not leave your camcorder or  
cassettes in a car or outdoors for an  
extended period. Excessive heat or  
cold may damage them.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camcorder Traveling and Cassette Tips  
Traveling Tips  
Write down your camcorder’s serial  
number and keep it separate from the  
camcorder when traveling. If your  
camcorder is lost or stolen, you will be  
able to identify it.  
Carry your camcorder in the carrying case  
when traveling. See page 52 for a  
specially designed soft case. An ordinary  
suitcase or carry bag does not offer the  
protection your camcorder needs. Treat  
your camcorder as carry-on luggage to  
protect it from rough handling.  
Make sure you have any plug adapters  
you need before taking your camcorder to  
other countries. Consult your dealer.  
Use extra care to avoid damage to your  
camcorder and accessories when operating  
them at a beach or pool. Spray, sand, and  
dust should be avoided. If your lens has  
been exposed to the elements, clean it  
only with proper lens cleaning supplies.  
Cassette Tips  
Store your cassettes vertically in their  
protective cases at normal room  
temperature.  
Do not use a cassette if it has been  
damaged or exposed to moisture. The  
tape may jam or damage your camcorder.  
Do not leave your camcorder or cassettes  
in a car or outdoors for an extended  
period. Excessive heat or cold may  
damage them.  
When you are finished recording, break  
off the safety tab on the cassette to prevent  
accidental erasure.  
Label your cassettes before storing them.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camcorder Features  
STOP/EJECT  
F.FWD (Fast Forward)  
REW (Rewind)  
POWER Switch in CAMERA  
REVIEW  
Microphone  
S
T
O
P/EJE  
C
T
E
DIT – A  
D
V
F.FWD  
+
P
LA  
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
OFF  
AUTO  
Quick Review  
Microphone  
The microphone picks up sound during a  
recording. It is more sensitive to sounds  
coming from the direction the lens is  
pointed.  
Press REVIEW when POWER is in  
CAMERA and the camcorder is in record  
pause to review the last few seconds of a  
recording.  
The camcorder will play back the last  
few seconds of the recording, return the  
tape to its previous position, and return to  
record pause.  
AI (Artificial Intelligence)  
The camcorder will automatically adjust  
focus, white balance and iris according to  
the recording conditions.  
Tape Positioning  
When POWER is in VCR and the  
camcorder is in the stop mode, you can  
quickly fast-forward or rewind the tape.  
• Press F.FWD (fast forward) to fast  
forward the tape. Press STOP/EJECT  
to stop fast-forwarding.  
• Press REW (rewind) to rewind the tape  
to the beginning. Press STOP/EJECT  
to stop rewinding.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camcorder Features  
Program AE (Auto Exposure)  
Program auto exposure automatically selects the shutter speed and adjusts the iris  
according to the shutter speed.  
AE:60  
Viewfinder Display  
The AE indicator for the shutter speed  
selected (1/60, 1/100, 1/120, 1/180,  
1/250, 1/350, 1/500, 1/750, 1/1000,  
1/1500, 1/2000, or 1/4000 second)  
appears in the viewfinder.  
Auto Focus  
The camcorder will focus on the subject in the center of the viewfinder.  
Auto focus operates on the telephoto “T” side from approximately 3.6 feet to infinity  
and on the wide-angle “W” side 3/8 of an inch from the lens surface to infinity.  
The following conditions may prevent auto focus from operating properly.  
• Subject has close foreground and  
background far away.  
• Subject not in center of the viewfinder.  
• Subject with shiny surfaces or sharp  
angles.  
• Two subjects at different distances that  
overlap.  
• Recording in low-light situations.  
• Recording through a window.  
• Subject with distinct horizontal stripes  
or small pattern.  
Macro Focus  
The macro-focus feature lets you focus on objects as close as 3/8 of an inch from the  
camcorder lens.  
Notes: Zooming is not possible when using  
macro focus. To change the size of the  
subject, move the camcorder’s lens closer or  
farther away from it.  
1. Press and hold zoom button “W” until  
the lens is completely zoomed out.  
2. Position the subject in the center of the  
viewfinder.  
For best results, increase illumination when  
recording using macro focus.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camcorder Features  
Electronic Indexing  
Each time you begin recording (after the camcorder has been turned off for at least  
four hours), the camcorder will automatically record an index mark at the beginning of  
the new recording.  
When you play back the indexed tape in a VCR that has a compatible indexing feature  
called “VHS Index Search System”, the invisible marks can be located automatically.  
See your VCR owner’s manual for index playback instructions.  
INDEX  
Viewfinder Display  
Note: The camcorder does not record index  
marks every time you stop and start recording.  
An index mark is recorded only once — at the  
start of each day’s recording session (or  
whenever the camcorder has been turned off  
for at least four hours).  
INDEX will appear briefly in the  
viewfinder to let you know the camcorder  
is recording an index mark.  
Time Remaining Display  
The time remaining display shows the amount of recording or playback time left on the  
tape in the camcorder.  
Viewfinder Display  
Once time remaining has been calculated,  
it will automatically be updated and  
readily available as long as the same tape  
remains in the camcorder.  
”– – – – – –”will appear for  
approximately ten seconds when you first  
start playing or recording a tape while the  
camcorder calculates the time remaining.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewfinder  
The camcorder’s viewfinder is a miniature monitor that displays the picture seen by  
the camcorder when recording. The viewfinder also can be used for viewing the tape  
during playback.  
When carrying or storing the camcorder, return the viewfinder to the original position  
to prevent possible damage.  
Viewfinder in  
operating position  
Eyepiece  
Viewfinder  
in carrying  
or storing  
position  
B R IG H T  
Pull here  
Caution: Pulling on the eyepiece may cause damage to the camcorder.  
1. Grasp the viewfinder and rotate it  
horizontally.  
2. Pull the viewfinder out from the  
camcorder and adjust the eyepiece for  
convenient viewing.  
Eyepiece Focus Control  
Eyepiece Focus  
Control  
The eyepiece focus control lets you set  
the focus of the viewfinder for your  
personal vision. If you wear eyeglasses,  
you probably can operate the camcorder  
without them.  
counter). Look through the viewfinder,  
and adjust the eyepiece focus control for  
your vision.  
The eyepiece focus control does not  
affect the focus of the picture actually  
recorded by the camcorder.  
Set the correct focus by focusing on one  
of the viewfinder’s displays (such as the  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewfinder  
Eyepiece BRIGHT, COLOR, and TINT Controls  
COLOR  
TINT  
B R IG H T  
BRIGHT  
BRIGHT Control  
COLOR and TINT Controls  
Viewfinder brightness can be adjusted  
by turning the BRIGHT control. This  
does not affect the picture actually  
recorded by the camcorder.  
The small COLOR and TINT controls  
are set at the factory and should require  
no adjustment.  
Tilt Adjustment  
For convenient viewing, you can rotate the eyepiece about 225º degrees.  
Caution: Do not  
force the eyepiece  
to rotate completely  
around. This will  
damage the  
eyepiece and/or the  
camcorder.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Displays in Viewfinder  
1
AE Shutter  
Speed  
5
6
Tape Counter  
AE:60  
0000M  
INDEX  
Time Remaining  
FADE  
2
3
ZOOM  
T
NO TAPE  
A/V DUB  
Battery Level  
7
ZOOM and  
Zoom Level  
Indicator  
INDEX Display  
8
W
10:30AM  
TAPE, NO TAPE,  
and TAPE END  
9
REC  
11/18/95  
Status  
4
10  
Time and Date  
Viewfinder Displays  
1
AE (Auto Exposure) Shutter Speed  
The shutter speed selected by the  
camcorder appears here. It is not  
recorded on the tape.  
A/V DUB for audio/video dubbing.  
A. DUB for audio dubbing.  
REC for recording.  
66 during fast forward.  
55 during rewind.  
2 Fade  
Press FADE to select white, wipe, or  
during record pause.  
zoom fade. It is not recorded on the  
tape.  
Tape Counter with Memory  
Stop (M)  
5
appears for white fade.  
appears for wipe fade.  
appears for zoom fade.  
The tape counter helps you locate  
tape segments. It is not recorded on  
the tape.  
• Press DISPLAY to turn memory  
stop on or off.  
Details are on page 29.  
3 ZOOM and Zoom Level  
• Details are on page 30.  
• The zoom level indicator appears  
when you press power zoom button  
T or W. ZOOM appears when you  
zoom in more than 12 times.  
Time Remaining (  
)
6
This display shows the amount of  
recording or playback time remaining  
on the tape. It is not recorded on the  
tape. Details are on page 21.  
Details are on page 28.  
Status  
4
The following displays appear in this  
area. They are not recorded on the  
tape.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Displays in Viewfinder  
AV (Audio/Video) DUB  
DATE/TIME  
DISPLAY  
S
E
T
O
P/EJE  
D
C
V
T
DIT – A  
F.FWD  
+
P
LA  
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
POWER  
Power  
Zoom  
Button  
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
FADE  
7
8
9
Battery Level (  
)
• TAPE END flashes when you have  
approximately three minutes  
recording time left on the cassette.  
• TAPE END briefly appears when  
you reach the end of the cassette  
during recording.  
This indicator shows the amount of  
time left for the rechargeable battery.  
It is not recorded on the tape.  
Details are on page 14.  
INDEX  
• These displays are not recorded  
when they appear.  
INDEX appears briefly when the  
camcorder automatically indexes the  
tape. It is not recorded on the tape.  
Details are on page 21.  
10 Time and Date Display  
• Press DATE/TIME repeatedly to  
display time and date, AUTO date,  
date only, or no date display when  
the camcorder is in record pause.  
• These displays are recorded when  
they appear.  
TAPE, NO TAPE, and TAPE END  
TAPE flashes when you try to  
record and the safety tab has been  
removed.  
TAPE flashes when a damaged tape  
is inserted. Remove the tape and  
replace it with a new one.  
Details are on pages 26-27.  
NO TAPE flashes when you try to  
record and there is no cassette in  
the camcorder.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Date and Time Display  
Set the Time and Date  
DATE/TIME  
REW (Rewind)  
F.FWD (Fast Forward)  
POWER  
STOP/EJECT  
REVIEW DISPLAY RESET DATE  
/TIME  
TITLER  
CAMERA OFF  
POWER  
VCR  
AV DUB  
REW  
PLAY  
F.FWD  
+
STOP/EJECT  
EDIT – ADV  
TITLE SEL  
S
T
O
P
/E  
J
E
C
T
E
D
IT –  
A
D
V
F.FWD  
+
P
L
A
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
1. Attach a power supply (battery or  
adapter/charger) to the camcorder.  
5. When the correct digit is displayed,  
press STOP/EJECT. The cursor will  
move to the next part of the display.  
2. Press and hold the small button on  
POWER and place in CAMERA.  
6. Repeat steps 4 and 5 to set the correct  
month, day, year, hour, minute(s), and  
AM/PM.  
3. Press DATE/TIME to display the date  
and time in the viewfinder. A flashing  
cursor lets you know which part of  
the display you are setting.  
7. After setting AM or PM, press  
DATE/TIME to remove the flashing  
cursor and start the internal clock.  
Note: If flashing cursor does not appear,  
press and hold DATE/TIME and then press  
STOP/EJECT.  
To Correct the Date or Time  
To correct the date or time, press and  
hold DATE/TIME and then press  
STOP/EJECT. The display will appear in  
the viewfinder along with the flashing  
cursor. Use F.FWD and REW to correct  
the time or date. Press DATE/TIME to  
remove the flashing cursor and start the  
clock.  
12:00AM  
1/ 1/95  
4. Repeatedly press F.FWD or REW until  
correct month appears. Press and hold  
the button to advance the digits faster.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Date and Time Display  
Recording Date and Time (or Date) on Your Tape  
The time and date (or date only) can be recorded on your tape. Whenever one of the  
displays appears in the viewfinder, it will be recorded.  
The camcorder has an auto-date feature that will record the date only for approximately  
ten seconds when you begin recording.  
Repeatedly  
Press DATE/  
TIME  
12:00AM  
1/1/95  
AUTO  
11/18/95  
Date and Time  
Auto Date – Date  
Automatically Recorded  
for Ten Seconds at  
Beginning of Recording  
11/18/95  
Date Only  
No Display  
Charging the Camcorder’s Built-in Clock Battery  
The camcorder has a built-in rechargeable clock battery.  
This battery must be charged approximately every two months.  
1. Attach a power supply (adapter/  
charger or charged battery) to the  
camcorder.  
Cautions: If this battery is not charged  
every two months, it will over-discharge  
and shorten its useful life.  
2. Make sure POWER is in OFF.  
Do not attempt to replace this battery.  
Take the camcorder to an authorized  
Servicenter.  
3. Leave the power supply attached at  
least 24 hours.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Zooming  
Power Zoom Buttons  
T = Telephoto  
W = Wide Angle  
S
T
O
P/EJE  
C
T
E
DIT – A  
D
V
F.FWD  
+
P
LA  
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
Using Power Zoom Buttons  
ZOOM  
T
ZOOM and Zoom  
Level Indicator  
W
To zoom in or out slowly, press the zoom  
button lightly. To zoom in or out  
• Press “W” to move the lens in the  
“wide-angle” direction.  
quickly, press the zoom button firmly.  
The zoom level indicator will appear  
briefly in the viewfinder.  
• Press “T” to move the lens in the  
“telephoto” (close-up) direction.  
ZOOM appears in the viewfinder when  
you zoom in more than 12 times.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fading In and Out of Scenes  
You can add a professional touch to your recordings when you fade in and out of  
scenes. Both the picture and sound will gradually appear or disappear. The speed of  
the fade is controlled by the camcorder.  
S
T
O
P
/E  
J
E
C
T
F.  
F
W
D
E
D
IT –  
A
D
V
P
L
A
Y
+
R
E
W
TITLE S  
E
L
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
FADE  
Select the Type of Fade  
Repeatedly Press FADE  
You can select white, wipe,  
or zoom fade.  
• Select white fade to fade  
in and out from a white  
screen.  
appears in  
the viewfinder.  
• Select wipe fade to fade  
in and out from a black  
Wipe Fade  
White Fade  
screen.  
appears in  
the viewfinder.  
• Select zoom fade to fade  
in and out while  
zooming.  
appears in  
the viewfinder.  
No Fade  
Zoom Fade  
Fade In  
Fade Out  
1. Place the camcorder in record pause.  
1. During recording, repeatedly press  
FADE to select the fade mode.  
2. Repeatedly press FADE to select fade  
Note: The last fade mode used will appear  
the first time you press FADE.  
mode.  
Note: The last fade mode used will appear  
the first time you press FADE.  
2. Press REC/PAUSE to stop recording.  
The picture and sound will gradually  
disappear.  
3. Press REC/PAUSE to start recording.  
The picture and sound will gradually  
appear in place of the blank screen.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tape Counter with Memory Stop  
The tape counter is automatically displayed in the viewfinder and acts as a handy  
reference to help you locate tape segments.  
RESET  
REW  
POWER  
DISPLAY  
F.FWD  
REVIEW  
DISPLAY RESE  
T
DATE  
/TIME  
TITLER  
CAMERA  
O
F
F
VCR  
AV DUB  
RE  
W
PLAY  
TITLE SE  
F.FWD  
+
STOP/EJE  
C
T
POWE  
R
L
EDIT – ADV  
S
T
O
P
/E  
J
E
C
T
F.  
F
W
D
E
D
IT –  
A
D
V
P
L
A
Y
+
R
E
W
TITLE S  
E
L
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
REC/  
PAUSE  
R E C / P A U S E  
T R A C K I
FADE  
ON  
LIGHT  
AUTO  
OFF  
Memory Stop  
The tape counter’s memory stop helps you locate a certain point on the tape. When  
memory stop is turned on, the tape will stop automatically during fast forward or  
rewind when the tape counter reaches “0000M”.  
Using Memory Stop:  
1. Press DISPLAY to turn memory stop  
on. “M” appears after tape counter  
when memory stop is turned on.  
4. Make sure POWER is in VCR. Then  
press REW (rewind). The tape will  
rewind until it reaches the tape counter  
reading of “0000M”.  
2. Locate the place on the tape you want  
to return to and press RESET to reset  
tape counter to “0000M”.  
Notes: Press DISPLAY to turn memory-stop  
feature on or off.  
Memory  
Stop On  
0000M  
Whenever memory stop is turned on, the  
camcorder will stop rewinding or fast  
forwarding when the counter reaches  
0000M”. To continue rewinding or fast  
forwarding the tape, press REW (rewind) or  
F.FWD (fast forward) again.  
3. Continue to record or play the tape.  
When you want to return to the place  
you marked, press REC/PAUSE to  
stop recording, or press STOP/EJECT  
to stop playback.  
The tape counter is automatically reset to  
0000” whenever a cassette is inserted.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
ProEdit® System  
• Flying Erase Head  
• Edit Search  
• Audio Dub  
• A/V (Audio and Video) Dub  
• Titler  
The camcorder incorporates a complete package of advanced editing features  
to make it easy and fun to edit your home videos like a professional. The  
major ProEdit® System features are described here and on the following pages.  
Flying Erase Head  
A separate erase head is mounted on the spinning  
headwheel (hence the term “flying”). The flying  
erase head allows you to make clean edits without  
“glitches” or “rainbow noise”.  
Edit Search  
The edit-search feature allows you to edit as you  
make your recording by using F.FWD, REW, and  
PLAY to precisely position the tape while the  
camcorder is in record pause.  
• Press and hold REW (rewind) to visually search  
the recorded tape in reverse.  
• Press and hold F.FWD (fast forward) to visually  
search forward on the recorded tape.  
• Press and hold PLAY to view the recorded tape at  
normal speed.  
When you release the button, the camcorder will  
return to record pause at that point on the tape.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
Audio Dubbing  
AV DUB Button  
S
T
O
P
/E  
J
E
C
T
E
D
IT – A  
D
V
F.FWD  
+
P
L
A
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
AV  
AV OUT/IN Switch  
OUT  
/
IN  
AUDIO  
IN  
OUT  
White  
Jack  
White Audio Plug  
Back of Mono  
VCR or Tape Deck  
White  
Audio Plug  
Audio/Video Cable  
(such as AH005)  
Yellow  
Yellow Video Plug  
(No connection)  
Video Plug  
(no connection)  
–OR–  
White  
Audio Plug  
AUDIO  
R IN L  
Yellow  
Video Plug  
(no connection)  
R OUT L  
White Audio Plug  
Back of stereo  
Audio/Video Cable  
(such as AH005)  
VCR, Tape Deck,  
Laser Disc Player  
or CD Player  
Y-Adapter  
(such as AH25)  
Yellow Video Plug  
(No connection)  
Note: You will need an optional audio/video cable, such as AH005 shown on page 54.  
If the audio source has separate left and right outputs, attach the audio plug to the one  
labeled MONO. If one is not labeled MONO, you may need a Y-adapter, as shown on  
page 54, to record audio from both the left and right channels.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
Audio Dubbing  
The audio dub feature lets you record new audio  
(sound) on a previously recorded tape without erasing  
the original video (picture). The previous audio is  
erased and replaced with the new audio.  
The audio dub feature increases your editing  
flexibility. Video segments can first be assembled  
and then a single narration or music background can  
be added.  
The new audio can be added two different ways.  
• You can speak into the camcorder’s built-in  
microphone.  
• You can connect an external sound system to the  
white AUDIO jack on the camcorder.  
To Audio Dub  
1. Press and hold the small button on  
POWER while sliding it to VCR.  
2. If you are recording from a source  
connected to the white AUDIO jack on  
the side of the camcorder, place AV  
OUT/IN switch to IN.  
A.DUB  
3. Insert the tape you want to audio dub  
and use PLAY, F.FWD, and REW to  
locate a point on the tape a few  
seconds before you want to begin  
dubbing.  
6. To begin dubbing, start the audio  
source and press REC/PAUSE.  
will disappear from the viewfinder  
while you are dubbing.  
7. Press STOP/EJECT when you are  
4. Press REC/PAUSE exactly where you  
want to begin dubbing. This will  
place the camcorder in play pause.  
finished dubbing.  
Remember: Place the AV OUT/IN switch  
to OUT to record on the camcorder.  
5. Press and hold AV DUB, and then  
press PLAY. Release both buttons at  
Notes: If you want to stop dubbing at a  
certain point on the tape, turn on memory  
stop, and set tape counter to “0000M” at the  
point where you want the dubbing to stop.  
The camcorder will stop dubbing  
the same time. A. DUB  
will appear  
in the viewfinder when the camcorder  
is ready to begin audio dubbing.  
automatically when it reaches “0000M”.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
Audio and Video Dubbing  
AV DUB Button  
S
T
O
P
/EJE  
C
T
E
D
IT – A  
D
V
F.FWD  
+
P
LA  
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
AV  
4
AV OUT/IN Switch  
OUT  
/
IN  
Yellow  
Jack  
White  
Jack  
White Audio Plug  
AUDIO  
OUT  
1
Yellow  
Video Plug  
Audio/Video Cable  
(such as AH005)  
VIDEO  
OUT  
3
2
Back of  
Yellow Video Plug  
VCR or  
White  
Audio Plug  
TV Monitor  
–OR–  
Yellow  
Video Plug  
White  
Audio  
Plug  
L
3
AUDIO  
OUT  
White Audio Plug  
Y-Adapter  
(such as AH25)  
R
Audio/Video Cable  
(such as AH005)  
1
VIDEO  
OUT  
Back of  
Stereo  
2
VCR or  
TV Monitor  
Yellow Video Plug  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
Audio and Video Dubbing  
The audio and video dubbing feature lets you record new  
audio (sound) and video (picture) on a previously  
recorded tape in the camcorder.  
The source for the dubbing is the camcorder’s  
microphone and camera or a source connected to the  
AUDIO/VIDEO jacks on the side of the camcorder.  
• To record from the camcorder’s microphone and  
camera, no special connections are required.  
• To record from an external video source (VCR,  
LaserDisc player, etc.), you will need an optional  
audio/video cable, such as AH005 shown on page 54.  
To Audio and Video Dub  
Note: If you are dubbing from a source  
connected to the AV OUT/IN jacks, be sure  
to start it playing.  
1. Press and hold the small button on  
POWER while sliding it in VCR.  
2. If you are recording from a source  
connected to the AUDIO/VIDEO jacks  
on the side of the camcorder, place the  
AV OUT/IN switch to IN.  
3. Insert the tape you want to dub and  
use PLAY, F.FWD, and REW to locate  
a point on the tape a few seconds  
before you want to begin dubbing.  
A/V DUB  
7. To begin dubbing, press REC/PAUSE.  
will disappear from the viewfinder  
while you are dubbing.  
4. Press REC/PAUSE exactly where you  
want to begin dubbing. This will  
place the camcorder in play pause.  
8. Press STOP/EJECT when you are  
5. Press and hold AV DUB, and then  
finished dubbing.  
press PLAY. Release both buttons at  
Remember: Place the AV OUT/IN switch  
to OUT to record on the camcorder.  
the same time. A. DUB  
will appear  
in the viewfinder when the camcorder  
is ready to begin audio dubbing.  
Notes: If you want to stop dubbing at a  
certain point on the tape, turn on memory stop  
and set the tape counter to “0000M” at the  
point where you want the dubbing to stop.  
The camcorder will stop dubbing  
6. Press and hold AV DUB, and then  
press PLAY again. Release both  
buttons at the same time. A/V DUB  
will appear in the viewfinder when the  
camcorder is ready to begin audio and  
video dubbing.  
automatically when it reaches “0000M.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
Titler  
The camcorder’s built-in titler can store two different  
titles in memory. Either title can be displayed and  
recorded at any time.  
The built-in character register contains over 45  
different characters for creating your titles. Each  
title can contain up to 32 characters on two lines.  
TITLE SEL –  
(Also REW)  
POWER in CAMERA  
TITLER  
TITLE SEL  
(Also PLAY )  
TITLE SEL +  
(Also F.FWD )  
EDIT–ADV  
(Also STOP/EJECT)  
REVIEW DISPLAY RESET DATE  
/TIME  
TITLER  
CAMERA OFF  
POWER  
VCR  
AV DUB  
REW  
PLAY  
F.FWD  
+
STOP/EJECT  
EDIT – ADV  
TITLE SEL  
S
T
O
P
/E  
J
E
C
T
E
D
IT – A  
D
V
F.FWD  
+
P
L
A
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
To Create a Title  
See the “Chart of Characters in Titler’s  
Register” below for the characters  
available.  
1. Attach a power source to the  
camcorder, press and hold the small  
button on POWER while sliding it to  
CAMERA. POWER indicator will  
light.  
5. After you have selected the first  
character, press EDIT–ADV to move  
the flashing cursor where you want  
your next character to appear.  
6. Repeat steps 4 and 5 until you have  
completed the title.  
2. Press TITLER to display titler  
graphics in the viewfinder. A  
flashing cursor will appear.  
Note: Press TITLE SEL (select) to select  
the other title page. Each time you press  
TITLE SEL, it will switch between the two  
title pages.  
7. Press TITLE SEL if you wish to create  
another title on the other title page.  
8. When you are finished, press TITLER  
to store the title and remove the title  
display from the viewfinder.  
3. Press EDIT–ADV to move the  
flashing cursor to the place you want  
to begin your title.  
4. Select the first character for your title  
by pressing TITLE SEL + or TITLE  
SEL – until the character you want  
appears in the viewfinder.  
Important Note: Remember to remove the  
titler graphics from the viewfinder for normal  
recording.  
Notes: You can scroll through the  
character register at a faster pace by  
pressing and holding TITLE SEL + or  
TITLE SEL –.  
To Correct an Error  
1. Press TITLER to display the titler  
3. Press TITLE SEL + or TITLE SEL –  
graphics in the viewfinder.  
until the correct character appears.  
Note: If you want to delete a character,  
press TITLE SEL + or TITLE SEL – until  
the blank space appears.  
2. Press EDIT–ADV until the flashing  
cursor is placed over the character you  
wish to correct.  
Chart of Characters in Titler’s Register  
A B C D E F G H I J K L M N O P Q R S  
T U V W X Y Z 0 1 2 3 4 5 6 7 8 9 ? Õ  
. / , Ð ; : < > ! (BLANK)  
(continued on next page)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ProEdit Features  
Recording Titles on a Tape in the Camcorder  
To record a title on a tape in the camcorder, follow the steps below.  
Note: If you want to record the other title  
page, press TITLE SEL to display it in the  
viewfinder.  
4. Press REC/PAUSE to start recording  
1. Attach a power source to the  
camcorder, slide POWER to  
CAMERA.  
2. Locate the place on the tape where  
you want to record the title.  
the title.  
5. After you have recorded the title for  
the desired length of time, press  
TITLER to remove titler graphics from  
the viewfinder. The camcorder will  
now record as normal. If you do not  
want to continue recording, press  
REC/PAUSE.  
Notes: If you record a title on a pre-  
recorded tape, the audio and video will be  
erased where the title is inserted. There  
will also be a three-to-four second pause of  
blank tape before the existing audio and  
video return.  
Audio and video dubbing titles onto  
existing tapes will eliminate the pauses of  
blank tape. Details are on pages 34-35.  
Important Note: Remember to remove the  
titler graphics from the viewfinder for normal  
recording.  
3. Press TITLER to display the titler  
graphics in the viewfinder.  
Recording Titles While Copying a Tape from Camcorder to Another VCR  
This method of adding titles lets you keep the original tape as it is, and add titles to the  
copy you are making on another VCR. Connect your camcorder to a VCR as shown  
on pages 44-45.  
1. Attach a power source to the  
camcorder.  
6. Start copying the tape from the  
camcorder to the VCR. Details for  
copying a tape are on pages 44-45.  
2. Place the tape you want to copy in the  
camcorder and place POWER in VCR.  
7. When you see the place on the tape  
you want to insert the title, press  
TITLER.  
3. Press TITLER to display the title you  
want to record. If you want to record  
the other title page, press TITLE SEL.  
The camcorder will recall the last title  
page displayed the next time you press  
TITLER.  
8. After you have recorded the title for  
the desired time, press TITLER to stop  
recording the title.  
9. Stop the camcorder and VCR when  
you are finished copying the tape.  
4. Press TITLER to remove titler  
graphics from the viewfinder.  
Important Note: Remember to remove the  
titler graphics from the viewfinder for normal  
playback.  
5. Place a blank tape in the VCR, and  
place the VCR in record pause.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording Tips  
Make a recording of your home and  
contents to store in a safe place in case of  
fire or theft.  
Be aware of video and audio backgrounds.  
Background details barely noticed while  
you are taping may show up as visual  
“clutter” on your recording. Background  
noises (especially TV sets, radios,  
household appliances, traffic sounds, etc.)  
can detract from the sound you want to  
record.  
Practice recording under a variety of  
lighting conditions. This will help you  
respond quickly whenever you see a scene  
you want to record.  
Fading in and out of scenes may make  
your videos appear more professional.  
Avoid long “still” shots of landmarks and  
scenic attractions. Recordings are more  
interesting if they include people and  
details. “Local color” will give travel  
videos lasting appeal. Consider recording  
a familiar or landmark scene from an  
unfamiliar vantage point for added  
interest. Remember to check the lighting  
before starting to record.  
Do not move the camcorder rapidly from  
side-to-side while recording. A steady,  
gradual “pan” avoids blurring and “jitter”.  
Use the viewfinder to make sure the  
camcorder is level while recording or your  
scenes will appear “tilted”.  
Make sure indoor scenes are well-lit to  
improve picture quality and color  
reproduction.  
Try to avoid taping backlit subjects  
indoors. Bright light behind your subject  
may cause the subject to appear too dark.  
Do not bump or tap the camcorder’s  
microphone while recording because this  
sound will be recorded.  
Include close-up shots of individuals  
when taping family outings or group  
functions.  
For a different perspective, try kneeling  
down (or laying) on the floor when  
recording children or pets.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording on the Camcorder from a VCR or TV Monitor  
To record on a tape in your camcorder from a VCR or TV monitor with  
AUDIO OUT and VIDEO OUT jacks, you will need an optional audio/video  
cable, such as AH005 shown on page 54.  
S
T
O
P
/EJE  
C
T
E
D
IT – A  
D
V
F.FWD  
+
P
LA  
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
AV  
4
AV OUT/IN Switch  
OUT  
/
IN  
Yellow  
Jack  
White  
Jack  
White Audio Plug  
AUDIO  
OUT  
1
Yellow  
Video Plug  
Audio/Video Cable  
(such as AH005)  
VIDEO  
OUT  
3
2
Back of  
VCR or  
TV Monitor  
Yellow Video Plug  
White  
Audio Plug  
–OR–  
Yellow  
Video Plug  
White  
Audio  
Plug  
L
3
AUDIO  
OUT  
White Audio Plug  
Y-Adapter  
(such as AH25)  
R
Audio/Video Cable  
(such as AH005)  
1
VIDEO  
OUT  
Back of  
Stereo  
2
VCR or  
TV Monitor  
Yellow Video Plug  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording on the Camcorder from a VCR or TV  
Installation  
2
3
1
Attach the white plug on one end of  
the audio/video cable to the AUDIO  
OUT jack on the VCR (or TV  
monitor).  
Attach the yellow plug on the same  
end to the VIDEO OUT jack on the  
VCR (or TV monitor).  
Attach the yellow plug on the other  
end of the audio/video cable to the  
yellow VIDEO jack and the white  
plug to the white AUDIO jack on the  
side of the camcorder.  
Note: If your VCR or TV monitor has  
stereo left and right AUDIO OUT jacks,  
attach the plug to the one labeled  
MONO. If one of the audio jacks is not  
labeled MONO, you may need a  
Y-adapter, such as AH25 shown on  
page 54, to hear both channels.  
4
Place the AV OUT/IN switch to IN.  
Recording Operation and How to Copy Tapes on the Camcorder  
1. A. Camcorder connected directly to  
TV monitor: Turn on the TV and  
tune it to the channel you want to  
record.  
2. Press and hold the small button on the  
camcorder’s POWER switch while  
sliding it to CAMERA.  
3. Insert a cassette in the camcorder with  
the safety tab intact.  
B. Camcorder connected to a VCR  
that is already connected to a TV:  
Turn on the VCR and select the  
channel you want to record (or  
place the cassette you want to copy  
in the VCR). If you are copying a  
tape, press PLAY on the VCR when  
you are ready to start copying.  
4. Press REC/PAUSE to start the  
camcorder recording.  
Note: If you are copying a tape, start the  
VCR playing the tape.  
5. Press REC/PAUSE on the camcorder  
when you are finished.  
Remember: Place the AV OUT/IN switch  
to OUT to record on the camcorder.  
Note: If you want to see what is being  
recorded, turn on the TV and tune it to  
the channel that you normally use to  
see the signal from the VCR.  
Caution: The unauthorized recording of television programs  
and other materials may infringe the rights of others.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewfinder Playback and Playback Features  
REW (Rewind)  
POWER Switch in VCR  
F.FWD (Fast Forward)  
REVIEW DISPLAY RESET DATE  
/TIME  
TITLER  
CAMERA OFF  
POWER  
VCR  
AV DUB  
REW  
PLAY  
F.FWD  
+
STOP/EJECT  
EDIT – ADV  
TITLE SEL  
STOP/EJECT  
S
T
O
P
/E  
J
E
C
T
E
D
IT – A  
D
V
F.FWD  
+
P
L
A
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
TRACKING  
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
Viewfinder Playback  
1. Attach a power supply to the  
camcorder.  
4. Press PLAY to begin playback. Adjust  
TRACKING if necessary.  
2. Press and hold the small button on  
5. Press STOP/EJECT when you are  
POWER while sliding it to VCR.  
finished.  
3. Press STOP/EJECT and insert the  
cassette you want to play back.  
Note: The camcorder can only play back  
tapes recorded at SP speed.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewfinder Playback and Playback Features  
Playback Features  
Picture Search  
Stop-Action Pause  
During playback you can visually search  
the tape at a higher speed in forward or  
reverse.  
During playback, you can view one  
frame of the tape.  
• Press REC/PAUSE to stop the action.  
• Press and hold F.FWD to search the  
tape forward.  
• Press REC/PAUSE again to return to  
normal playback.  
• Press and hold REW to search the tape  
in reverse.  
Caution: Pause is designed for  
momentary interruptions and should not  
be used for an extended period of time.  
If the camcorder remains in pause for  
more than five minutes, it will  
automatically remove the tape from the  
spinning heads to prevent excessive  
tape wear.  
• Release the button to return to normal  
playback.  
Tracking  
T
IN  
T
C
O
LO  
R
BATTERY  
D
C IN  
9.5V  
TRACKING  
(Also Power Zoom)  
Remove the cassette to reset the  
camcorder’s tracking to its preset center.  
When you play a tape not recorded on  
your camcorder, streaks may appear.  
To remove the streaks, press either  
TRACKING button to move the streaks  
up or down and out of the picture.  
The TRACKING buttons only affect tape  
playback. They have no effect during  
recording.  
Press either TRACKING button during  
stop-action (play-pause) to reduce picture  
“jitter” (picture bouncing up or down).  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback on a TV or VCR with AUDIO and VIDEO IN Jacks  
To connect your camcorder to a TV monitor (or VCR) with AUDIO IN and VIDEO IN  
jacks, you will need an optional audio/video cable, such as AH005 shown on page 54.  
If your TV is already connected to a VCR, you can attach the camcorder to the VCR  
and watch what the camcorder is recording or playing on the TV.  
S
T
O
P
/E  
J
E
C
T
E
D
IT – A  
D
V
F.FWD  
+
P
L
A
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
AV  
4
AV OUT/IN Switch  
OUT  
/
IN  
White  
AUDIO  
Jack  
Yellow  
VIDEO  
Jack  
White Audio Plug  
AUDIO  
IN  
1
Yellow  
Video Plug  
VIDEO  
IN  
Audio/Video Cable  
(such as AH005)  
3
2
Back of  
VCR or  
TV Monitor  
Yellow Video Plug  
White  
Audio Plug  
–OR–  
Yellow  
Video Plug  
3
White  
Audio Plug  
L
AUDIO  
IN  
White Audio Plug  
1
Y-Adapter  
(such as AH25)  
R
Audio/Video Cable  
(such as AH005)  
VIDEO  
IN  
Back of  
Stereo  
2
VCR or  
TV Monitor  
Yellow Video Plug  
Caution: The unauthorized recording of television programs and other materials  
may infringe the rights of others.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback on a TV or VCR with AUDIO and VIDEO IN Jacks  
2
1
Attach the yellow plug on the same  
end of the audio/video cable to the  
VIDEO IN jack on the TV or VCR.  
Attach the white plug on one end of  
the audio/video cable to the AUDIO  
IN jack on the TV or VCR.  
Note: If your TV (or VCR) has stereo  
left and right AUDIO IN jacks, attach the  
plug to the one labeled MONO. If one of  
the jacks is not labeled MONO, you may  
need a Y-adapter, such as AH25 shown  
on page 54, to hear both channels.  
3
Attach the yellow plug on the other  
end of the audio/video cable to the  
yellow VIDEO jack and the white  
plug to the white AUDIO jack on the  
side of the camcorder.  
4
Place the AV OUT/IN switch to OUT.  
Playback Operation and How to Copy Tapes on a VCR  
sliding it to VCR. Insert the cassette  
you want to playback (or copy).  
1. A. Camcorder connected directly to  
TV monitor: Turn on the TV and  
tune it to its video input channel.  
Note: The camcorder can only play back  
tapes recorded at the SP speed.  
B. Camcorder connected to VCR that  
is already connected to TV: Turn  
on VCR and place it in the “line” or  
“camera” mode. (If your VCR does  
not have a “line” or “camera”  
mode, consult the VCR owner’s  
manual.) Operate the TV as you  
normally do to see the signal  
3. Press PLAY on the camcorder. To  
copy what the camcorder is playing,  
place a blank cassette in the VCR and  
start the VCR recording. Adjust the  
tracking on the camcorder if necessary.  
Details are on page 43.  
• During playback, use the playback  
features described on page 43.  
coming from the VCR.  
4. Press STOP/EJECT when you are  
2. Press and hold the small button on the  
finished.  
camcorder’s POWER switch while  
Watching What the Camcorder is Seeing or Recording on the TV  
2. Press and hold the small button on the  
camcorder’s POWER switch while  
sliding it to CAMERA. Insert the  
cassette you want to record on.  
Note: When the camcorder is used as a  
camera, turn the TV’s volume down to  
prevent a high-pitched squeal caused by  
feedback.  
3. Press the camcorder’s REC/PAUSE  
button to begin recording. You can  
watch what the camcorder is seeing or  
recording on the TV screen.  
1. A. Camcorder connected directly to  
TV: Turn on the TV, and tune it to  
its video input channel.  
B. Camcorder connected to VCR that  
is already connected to TV: Turn  
on VCR and place it in the “line” or  
“camera” mode. (If your VCR does  
not have a “line” or “camera”  
mode, consult the VCR owner’s  
manual.) Operate the TV as you  
normally do to see the signal  
coming from the VCR.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback on a TV Without Audio and Video Inputs  
To connect your camcorder to a TV without audio and video input jacks. You will  
need an optional RF output adapter (such as CRF95) and an optional coaxial RF cable  
(such as AH065G or AH066G) shown on page 54.  
S
T
O
P
/E  
J
E
C
T
E
D
IT –  
A
D
V
F.FWD  
+
P
L
A
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
Antenna  
OR  
FADE  
1A  
1B  
OR  
ON  
LIGHT  
AUTO  
OFF  
AV  
4
AV OUT/IN Switch  
Antenna  
OUT  
/
IN  
Optional 300/75 ohm  
Transformer  
(such as 193983)  
3
Back of TV  
VHF  
Channel Selector  
OR  
IN  
FROM  
ANT  
VHF  
Optional RF Output Adapter  
(such as CRF95)  
Optional 75-300 Ohm  
Transformer  
Optional Coaxial RF Cable  
(such as AH065G or AH066G) TO TV  
OUT  
Disconnect the VHF antenna from  
your TV. If you are going to leave  
the RF adapter connected to the TV,  
connect the antenna to the RF output  
adapter.  
2 Attach one end of coaxial RF cable  
to OUT TO TV connector on RF  
1
adapter, and attach other end of the  
cable to VHF input on TV as shown.  
Note: If TV has screw terminals, you  
may need an optional 75-to-300 ohm  
transformer, such as AH011.  
A.If antenna is round 75-ohm cable,  
connect it to IN FROM ANT  
3 Attach RF output adapter’s yellow  
plug to the VIDEO jack, small plug  
to the RF DC OUT jack, and white  
plug to the AUDIO jack on the side  
of the camcorder.  
connector on RF output adapter.  
B.If antenna is flat twin-lead,  
connect flat-lead connectors to  
screw terminals on optional 300-  
75 ohm transformer. Then  
connect transformer to IN FROM  
ANT connector on RF output  
adapter.  
4
Place the AV OUT/IN switch to  
OUT.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback on a TV Without Audio and Video Inputs  
5. Press PLAY on the camcorder. Adjust  
tracking on the camcorder, if  
necessary. Details are on page 43.  
Playback Operation  
1. Set the channel selector switch on the  
RF output adapter to CH3 or CH4.  
• During playback, use the playback  
features described on page 43.  
2. Turn on the TV and tune it to the same  
channel (3 or 4) you selected with the  
channel selector switch on the RF  
output adapter.  
6. Press STOP/EJECT on the camcorder  
when you are finished playing back the  
tape.  
3. Press and hold the small button on the  
camcorder‘s POWER switch while  
sliding it to VCR.  
4. Insert the cassette you want to play  
back into the camcorder.  
Note: The camcorder can only play back  
tapes recorded at the SP speed.  
Watch What the Camcorder is Seeing or Recording on the TV  
1. Turn on the TV and tune it to channel  
3 or 4 (the same channel you selected  
with the CH3/CH4 switch on the RF  
output adapter).  
3. Press the camcorder’s REC/PAUSE  
button to begin recording. You can  
watch what the camcorder is seeing  
or recording on the TV screen.  
Note: When the camcorder is used as a  
camera, turn the TV’s volume down to  
prevent a high-pitched squeal caused by  
feedback.  
2. Press and hold the small button on the  
camcorder’s POWER switch while  
sliding it to CAMERA. Insert the  
cassette you want to record on.  
Normal TV Viewing  
from the camcorder or turn the  
camcorder’s power off.  
For normal TV viewing, you can leave  
the RF output adapter hooked up to the  
TV. Just disconnect the adapter’s plug  
Note to Cable-TV Installer: This reminder is provided to call your attention to Article  
820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code,  
Part I), that provides guidelines for proper grounding and, in particular, specifies that the  
cable ground shall be connected to the grounding system of the building as close to the  
point of cable entry as practical.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color Enhancement Light  
The color enhancement light helps create brighter, sharper pictures.  
S
T
O
P/EJE  
C
T
E
DIT – A  
D
V
F.FWD  
+
P
LA  
Y
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
Light  
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
LIGHT AUTO/OFF/ON  
To Use the Color Enhancement Light  
Notes: Turn on the light only when you  
need it. The power consumption of the  
light is approximately two-thirds that of the  
camcorder. When the light is on, the  
operation time of the rechargeable battery  
is reduced.  
1. Attach the rechargeable battery or  
AC adapter/charger to power the  
camcorder.  
2. Press and hold the small button on  
POWER and place it in CAMERA.  
Avoid bumping or shaking the light when  
in use. The light’s bulb is sensitive when  
hot and may burn out.  
3. Select a position for the LIGHT  
AUTO/OFF/ON switch.  
• Place in AUTO to have the light  
automatically turn on when the  
camcorder is aimed at a dark object  
and turn off when aimed at a bright  
object.  
Do not allow water to drop on the light  
when in operation.  
Dangers: During operation and after  
using the light, the front surface and  
bulb of the light will be very hot. To  
avoid burns, do not touch them.  
Note: A cassette must be inserted for  
AUTO to operate.  
• Place in ON to have the light turn on  
whenever POWER is in CAMERA.  
To prevent overheating, do not block  
or cover the ventilation holes on the  
color enhancement light.  
• Place in OFF to turn off the light.  
If the camcorder is left in record pause  
for more than five minutes, the power  
and light automatically turn off. Press  
REC/PAUSE to turn camcorder back  
on.  
Never use the color enhancement light  
in the vicinity of explosives or highly  
flammable materials.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color Enhancement Light  
Removing and Replacing the Front Case of the Light  
Light  
Bulb  
Front Case  
Reflection Plate  
Lower Hook  
To Remove and Replace Light Case  
Notes: Do not touch the bulb with your  
fingers. It may shorten its service life.  
1. To remove front case, press and hold  
the lower hook while removing it.  
Make sure the front case of the light is  
properly attached after removing it or  
replacing a bulb.  
2. To replace the front case, pass the  
bulb through the hole of the reflection  
plate, and attach the lower hook to the  
light.  
When replacing the bulb, only use #221111 to  
reduce the risk of fire and other hazards.  
3. Press front of case to light.  
See the installation instructions packed with  
the replacement bulb when replacing the bulb.  
Caution: Use only bulb #221111 when  
replacing the bulb to reduce the risk of  
fire or other hazards.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attaching the Shoulder Strap  
The shoulder strap is designed to let you carry the camcorder from your shoulder and  
— when you are ready to shoot — bring the camcorder to shooting position in one  
quick movement.  
Cautions: When carrying the camcorder with the shoulder strap, place the  
viewfinder in its original position. This helps prevent possible damage to the  
viewfinder from bumping against your body as you move.  
Make sure the shoulder strap is firmly attached before using it to carry your camcorder.  
To Attach the Shoulder Strap  
1. Unfasten one end of the shoulder strap from the buckle. Make sure you leave the  
buckle on the strap.  
2. Thread one end of the shoulder strap through one of the shoulder strap rings as  
shown below in diagrams A and B.  
Diagram B  
Diagram A  
TINT  
C
O
LO  
R
BATTERY  
Shoulder Strap Rings  
3. Thread the strap back into the buckle as shown below. Pull on the strap and make  
sure it is fastened correctly and tightly before using it to support your camcorder.  
4. Repeat steps 1–3 to attach the other end of the shoulder strap.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing Carrying Case  
The carrying case that came with your camcorder is specially designed to provide  
protection for your camcorder and its accessories. See below for details on packing  
your case.  
Two Hour Battery  
Camcorder  
Cassette Tape  
One Hour Battery  
Audio/Video Cable  
Adapter/Charger  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional Accessories  
We invite you to take a look at some great ideas for sparking creativity and adding to  
the fun of using your camcorder. These pages have a selection of accessories to help  
make your memorable moments look and sound even better.  
To order accessories, contact your local dealer.  
Accessories are available by calling toll-free or by using the order form  
on page 57.  
AC028A Soft Camcorder Case  
This case provides exceptional protection and  
utility for full size camcorders and most  
accessories. It is constructed of rugged, 1000  
denier weight, Cordura nylon fabric for years  
of reliable service and good looks.  
Three outside pockets provide ample  
accessory storage with mesh-covered lens  
filter compartment and built-in holders for  
memo pads, pens, and other accessories. The  
hand grip and adjustable shoulder strap allow  
for convenient, comfortable transportation of  
the camcorder.  
VCC1000 Video Color Control Center  
The VCC1000 is two accessories in one. The  
color control center allows you to adjust the  
color intensity, tint, white balance, and  
sharpness of tapes being dubbed. This is  
especially helpful when the original tape was  
produced in poor lighting conditions or poor  
color settings.  
The second feature, the character generator,  
lets you create titles that can be recorded on  
your tapes. This lets you add a professional  
and/or personal touch to your home videos.  
All specifications and descriptions of accessories  
are subject to change without notice.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional Accessories  
DCC096 DC (Battery) Car Cord  
This DC car cord enables you to operate  
your camcorder from your car, truck, or  
RV by plugging the car cord directly into  
the vehicle’s cigarette lighter.  
Caution: Do not use any other car cord  
with this camcorder.  
CPS014 AC Adapter/Charger  
This adapter/charger operates on 100-  
240 volts, 50/60 Hz, so it can be used  
almost anywhere in the world to power  
your camcorder and recharge the  
EP096FS battery supplied with your  
camcorder.  
It also charges the EP096FL (2 hour)  
battery. A simple plug adapter may be  
required in some countries.  
EP096FS and EP096FL Rechargeable Batteries  
These rechargeable lead-acid batteries  
are specifically designed for long life.  
The EP096FS can power your camcorder  
up to one hour and the EP096FL up to  
two hours (depending on how much you  
use the light, zoom, and pause).  
Both batteries can be recharged with  
the AC adapter/charger that came  
packed with your camcorder. First  
charging takes approximately two  
hours for the EP096FS and three  
hours for the EP096FL.  
(continued on next page)  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional Accessories  
AH005 Audio/Video Cable  
This six foot audio/video dubbing cable is used to  
connect your camcorder to a VCR or TV monitor to  
copy tapes.  
CRF95 RF Output Adapter  
This adapter is used with coaxial RF cable (AH065G or  
AH066G) to connect your camcorder to a standard TV (one  
without audio/video input jacks) for playback. If your antenna  
cable is the flat twin-lead type attached by two screws, you  
will also need a 300-75 ohm transformer such as 193983. If  
your TV has 300 ohm VHS screw terminals, you will need an  
optional 75/300 ohm transformer such as AH011.  
Coaxial RF Cables  
These RF cables are used with the RF output adapter to  
connect your camcorder to a standard TV (one without  
audio/video input jacks) for playback.  
If your antenna cable is the flat twin-lead type attached by  
two screws, you will also need a 300-75 ohm transformer  
such as 193983.  
AH065G (6-ft)  
AH066G (10-ft)  
If your TV has 300 ohm VHS screw terminals, you will need  
an optional 75-300 ohm transformer such as AH011.  
193983 Cable Transformer  
This 300-to-75 ohm transformer is used to connect a  
standard 300-ohm antenna twin-lead to a standard round  
75-ohm connector.  
AH011 Cable Transformer  
This 75-to-300 ohm transformer is used to connect a  
standard 75-ohm antenna cable, such as AH065G or  
AH066G, to the 300-ohm screw terminals on a TV.  
AH25 Y-Adapter  
This Y-adapter allows you to connect your camcorder’s mono  
audio cable to a stereo TV or VCR.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional Accessories  
Removing the Lens Hood  
The lens hood can be removed so you can attach optional accessories, such as wide-  
angle lens, lens extender, or lens filter kit.  
To remove the lens hood, place your hand flat against the lens hood and turn it  
counterclockwise. Do not grasp the end of the lens hood.  
S
T
O
P
/E  
J
E
C
T
F.FWD  
+
E
D
IT –  
A
D
V
P
L
A
Y
R
E
W
TITLE S  
EL  
S
E
T
D
O
IT –  
P
/E  
J
A
E
D
C
V
T
A
V D  
U
B
V
C
R
F.FWD  
+
O
F
F
P
L
A
Y
O
W
E
R
R
E
W
TITLE S  
EL  
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
R E C / P A U S E  
T R A C K I N G  
R E C / P A U S E  
T R A C K I N G  
FADE  
FADE  
ON  
LIGHT  
AUTO  
OFF  
ON  
LIGHT  
AUTO  
OFF  
Attaching Accessory Lens  
Remove the lens hood as shown above.  
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
OFF  
AUTO  
Turn the accessory lens clockwise into the camcorder’s lens. Make sure the lens is  
tightened firmly, but do not over tighten.  
All specifications and descriptions of accessories are subject to change without notice.  
(continued on next page)  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional Accessories  
Using an Optional Tripod  
Mounting the camcorder on a tripod, such as AC031 or AC040, will keep the  
camcorder steady and produce excellent video results.  
AC031 Deluxe Tripod  
This tripod’s fluid effect head provides  
smooth camera pan and tilt. Its quick-  
S
E
T
D
O
IT –  
P
/E  
J
A
E
D
C
V
T
F.  
F
W
D
P
L
A
Y
+
R
E
W
TITLE S  
E
L
A
V D  
U
B
V
C
R
O
F
F
E
C
A
M
E
R
A
P
O
W
R
T
IT  
L
E
R
D
/TIM  
A
T
E
E
R
E
S
E
T
D
IS  
P
L
A
Y
R
E
V
IE  
W
release mount makes it easy to attach or  
remove the camcorder. The grooved,  
tubular 3-section leg design folds down  
to 24" when not in use and weighs only  
4-1/4 lbs. Rubber feet allow for sure  
footing and the built-in retractable leg  
spikes eliminate the need for removing  
the feet.  
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
OFF  
AC040 Heavy Duty Tripod  
This high-end tripod is equipped with  
many professional features that enable  
you to produce professional results. The  
spring-flow head system combines both  
fluid and spring action for smooth  
“panning” and tilt action. It features  
heavy-duty 30 mm “D-channel” styled  
legs, oversized quick-release pad, click  
stop tilt adjustment, pan-drag tension  
adjustment, tilt-lever lock, transferable  
handle, bubble level, adjustable elevator  
friction tube, non-skid rubber feet with  
retractable spikes and quick-release leg  
lever locks.  
Caution: Before using a tripod, make sure it is stable enough to hold the camcorder  
without falling over. Do not transport the camcorder attached to the tripod.  
When attaching your camcorder to a tripod, be careful not to force the tripod screw  
into the camcorder’s tripod mounting hole.  
The tripod screw should not protrude into the camcorder more than approximately  
three-eighth (3/8) inch. Forcing the screw could damage the mounting hole on the  
bottom of the camcorder.  
All specifications and descriptions of accessories are subject to change without notice.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessory Order Form  
Order Form for Camcorder Models CC423  
Description  
Soft Camcorder Case  
Deluxe Tripod  
Heavy Duty Tripod  
Audio/Video Cable  
Cable Transformer  
RF Coaxial Cable (6-ft.)  
RF Coaxial Cable (10-ft.)  
Y-Adapter  
Part No.  
AC028A  
AC031  
AC040  
AH005  
Price  
Qty.  
Total  
$ 89.95  
$ 99.95  
$169.95  
$ 10.99  
AH011  
$
$
$
$
1.90  
6.99  
8.99  
1.95  
AH065G  
AH066G  
AH25  
Rechargeable Battery  
Rechargeable Battery  
AC Adapter/Charger  
RF Output Adapter  
Car Cord  
Video Color Control Center  
300-75 Cable Transformer  
DC Cable  
EP096FS  
EP096FL  
CPS014  
CRF95  
DCC096  
VCC1000  
193983  
209342  
227327  
$ 74.95  
$ 89.95  
$179.95  
$ 49.95  
$ 49.95  
$349.00  
$
6.95  
$ 12.95  
$ 13.95  
Shoulder Strap  
Replacement Bulb (4 watt)  
for Built-in Light  
AC Adapter/Charger (Supplied)  
221111  
$ 12.95  
$169.95  
221355  
or  
221356  
Prices are subject to change without notice.  
Total Merchandise ($10 Minimum Order)......................  
$__________  
$__________  
Sales Tax.........................................................................  
We are required by law to collect the appropriate sales tax  
for each individual state, county, and locality to which  
the merchandise is being sent.  
Shipping, Handling, and Insurance.................................  
$
5.00  
Total Amount Enclosed ................................................  
Use VISA or MasterCard preferably. Money order or  
check must be in U.S. currency only. No COD or cash.  
$__________  
• Allow 8 weeks for delivery.  
• All accessories are subject to availability.  
Please complete other side also  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessory Order Form  
Charge your order on your VISA  
or MasterCard by  
filling in below  
USE YOUR CREDIT CARD  
®
IMPORTANT: Copy complete account number  
from your VISA card  
My card expires:  
s
r
r
TM  
IMPORTANT: Copy complete account number  
from your MasterCard  
Copy Number  
above your  
name on  
My card  
expires:  
MasterCard  
AUTHORIZED SIGNATURE  
Prices are subject to change without notice.  
Print or type your name and  
address clearly. This will be your  
mailing label.  
A complete and correct order will  
save you days of waiting.  
Name:  
Street:  
Apt:  
Zip:  
City:  
State:  
Please make sure that both sides of this form have  
been filled out completely.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessory Order Form  
To order accessories, contact your local Dealer.  
If a dealer is not nearby, you can also follow the directions below to order by  
telephone or direct-by-mail.  
United States and Canada Orders  
To place your order by phone, have your Visa or MasterCard ready and call the toll-  
free number listed below between 8AM and 8PM Eastern Standard Time. Use this  
number only to place an order for accessory items listed on this order form.  
1 – 800 – 338 – 0376  
Most times your order will be shipped UPS within 72 hours of receipt. If ever it is not  
possible to ship within 30 days, we will notify you with an update on your order and  
an option to cancel.  
To place your order by mail, detach and mail the completed order form with credit  
card information, money order, or check in U.S. currency (made payable to Thomson  
Consumer Electronics, Inc.) to the following address:  
Video Accessories  
PO Box 8419  
Ronks, PA 17573  
For more information on these accessories (or current prices), write to the  
following address:  
Video Accessories Customer Service  
Thomson Consumer Electronics, Inc.  
Distributor & Special Products  
2000 Clements Bridge Rd  
Deptford, NJ 08096-2088  
International Orders  
This offer is valid only in the United States and Canada. For international orders,  
please send your request for a price quotation (not an order) to:  
International Customer Service  
Thomson Consumer Electronics, Inc.  
Distributor & Special Products  
2000 Clements Bridge Rd  
Deptford, NJ USA 08096-2088  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and Maintenance  
Keep dust and grit from entering the  
camcorder’s cassette door. Dust and grit  
are abrasive and cause excessive wear to  
both the camcorder’s recording and  
playback heads and cassettes.  
Always replace the lens cap on the lens  
when the camcorder is not in use.  
The camcorder can be damaged by  
improper storage or handling. Do not  
subject the camcorder to swinging,  
shaking, or dropping.  
Do not use strong or abrasive detergents  
when cleaning your camcorder. They  
may damage the camcorder.  
Do not store the camcorder in  
temperatures below -22ºF (-30ºC) or  
above 149ºF (65ºC).  
Before handling your camcorder, make  
sure your hands and face are free from  
any chemical products such as suntan  
lotion, as it may damage the finish.  
When the camcorder is not in use, always  
remove the cassette and AC adapter/  
charger or battery.  
Do not touch the lens with your fingers!  
The oil from your skin may damage the  
lens. To clean the lens, always use lens-  
cleaning tissues and a commercially  
prepared cleaning solution designed for  
use on camera lens.  
Retain the original carton for future  
storage or shipping purposes.  
Things to Avoid  
Do not aim your camcorder at the sun or  
other bright objects or leave your  
camcorder in direct sunlight. Doing so  
could permanently damage the  
Do not operate or leave your  
camcorder in extremely humid  
environments.  
Do not operate the camcorder for  
extended periods in temperatures  
below 40ºF (4ºC) or above 95ºF  
(35ºC).  
camcorder’s internal parts.  
Avoid operating your camcorder after  
moving it from a cold location to a warm  
location. Moisture may cause the tape to  
stick to the headwheel and damage the  
headwheel or tape. Give the camcorder 2  
to 3 hours to reach a stable temperature  
before inserting a cassette.  
Do not expose the camcorder or  
adapter/charger to rain or moisture.  
If either component becomes wet,  
turn off the power and take the unit to  
an Authorized RCA Camcorder  
Servicenter.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and Maintenance  
Cleaning the Camcorder  
To clean the camcorder’s exterior, remove any power source connected to the  
camcorder and gently wipe it with a clean soft cloth.  
S
T
O
P
/E  
J
E
C
T
F.  
F
W
D
E
D
IT –  
A
D
V
P
L
A
Y
+
R
E
W
TITLE S  
E
L
A
V D  
U
B
V
C
R
O
F
F
O
W
E
R
Caution: Use of strong cleaning  
products, such as those containing  
alcohol or benzine, may damage  
the camcorder.  
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
FF  
O
Cleaning the Camcorder’s Lens  
To clean the camcorder’s lens, blow it with a blower brush, and then gently wipe the  
lens with cleaning tissue and commercially prepared cleaning solution designed for use  
on camera lens. Improper cleaning may scratch the lens.  
S
T
O
P
/E  
J
E
C
T
F.  
F
W
D
E
D
IT –  
A
D
V
P
L
A
Y
+
R
E
W
TITLE S  
E
L
A
V D  
U
B
V
C
R
O
OW  
F
F
E
Caution: Do not touch the lens  
with your fingers. The oil from  
your skin can damage the lens.  
R
R E C / P A U S E  
T R A C K I N G  
FADE  
ON  
LIGHT  
AUTO  
FF  
O
Cleaning the Camcorder’s Viewfinder  
The viewfinder eyepiece can be removed for cleaning.  
1. Turn the eyepiece counterclockwise and pull it  
out.  
2. Gently use a cotton swab or blower brush to  
remove dust.  
3. Reattach the eyepiece by aligning the reference  
marks, and then turn the eyepiece clockwise.  
Mark  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble Checks  
Troubles sometimes are caused by simple “faults” that you can easily correct without  
the help of a service technician by first checking a few basic remedies.  
Before you call or take your camcorder to an Authorized RCA Camcorder Servicenter,  
look below for the type of trouble you are experiencing. Then perform the simple  
checks and adjustments listed for that trouble.  
Trouble  
Checks and Adjustments  
No Power  
(POWER Indicator  
Will Not Come On)  
• If using the rechargeable battery, it may need  
recharging.  
• If using the AC adapter/charger, make sure it is  
plugged into a working AC outlet.  
Will Not Record or  
Play Back  
• Make sure there is a cassette in the camcorder.  
• Try ejecting and re-inserting the cassette.  
• The cassette tape is broken — try another cassette.  
• You have reached the end of the cassette — try  
rewinding it.  
• Moisture condensation may cause the tape to stick to  
the headwheel and damage the headwheel or tape.  
Give the camcorder 2 to 3 hours to reach a stable  
temperature before re-inserting a cassette.  
Will Not Play Back  
Will Not Record  
POWER switch must be in VCR.  
• Safety tab has been removed from cassette.  
See page 16.  
• POWER switch must be in CAMERA.  
A/V OUT/IN switch must be in OUT to record on the  
camcorder.  
No Picture in Viewfinder  
• Make sure the lens cap has been removed.  
Tape Does Not Rewind  
or Fast Forward  
• Make sure titler graphics do not appear in viewfinder.  
Press TITLER to remove them.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble Checks  
Trouble  
Checks and Adjustments  
Tape Stops During  
Rewind or Fast  
Forward  
• The tape counter’s memory-stop feature may be  
turned on. When an “M” appears behind the tape-  
counter display, the camcorder will stop rewinding or  
fast-forwarding when the counter reads “0000M”.  
Press the REW (rewind) or F.FWD (fast forward)  
button again to continue, or press DISPLAY to turn  
off memory stop.  
Camcorder Remains  
in Play Pause  
• Press REC/PAUSE to return to normal playback.  
Poor Picture Quality  
During Recording  
• There is insufficient light. Add more light.  
• Use the color enhancement light to add more light.  
Details are on pages 48-49.  
Viewfinder Displays Are  
Out of Focus  
• Try adjusting the eyepiece focus control. Details are  
on page 22.  
Poor Auto-Focus  
Operation  
• Lens may be smudged and image appears unfocused.  
• Viewfinder eyepiece focus or BRIGHT control may  
be adjusted incorrectly. Details are on pages 22-23.  
• Tape was recorded on a different camcorder or VCR.  
If the picture contains black-and-white streaks, press  
one of the TRACKING buttons to correct.  
Poor Picture Quality  
During Playback  
• Camcorder only has one speed (SP). If the tape was  
recorded on a different VCR at a different speed, it  
cannot be played back in this camcorder.  
• Subject may have been too far from the camcorder.  
Recorded Audio is Too  
Low  
(continued on next page)  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble Checks  
Trouble  
Checks and Adjustments  
AE Shutter-Speed or  
INDEX Indicator Does  
Not Appear in  
POWER switch must be in CAMERA.  
Viewfinder  
Date and Time (or Date)  
were Recorded on the  
Tape  
• Date and time (or date) will be recorded on the tape  
whenever they appear in the viewfinder. Press  
DATE/TIME to remove them from the viewfinder  
when recording.  
Color in Viewfinder  
Does Not Look Natural  
and needs Adjustment  
The COLOR and TINT controls may need adjustment.  
Caution: Use a plastic screw driver to carefully  
adjust these delicate controls.  
Date and Time Appear  
Incorrect  
• Make sure the date and time have been set. Details  
on page 26.  
• The camcorder’s internal clock battery may need  
recharging. Details on page 27.  
Camcorder Does Not  
Turn On and/or  
Function Buttons Will  
Not Operate  
• Remove the power source.  
After one minute press the  
reset switch gently using a  
non-metallic pointed item,  
such as a toothpick, until you  
feel a click. This resets the  
camcorder to the factory  
AV  
settings and erases the date,  
OUT  
/
IN  
time, and custom settings.  
Reset Switch  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customer Assistance and Service  
Thomson provides a toll-free telephone  
You can reach Thomson at the  
following number:  
number to help you with any problems  
you may encounter with your camcorder.  
Many can be diagnosed over the phone,  
and if necessary, a replacement unit can  
be shipped to you. Please have your  
camcorder model/serial number and date  
of purchase ready when you call. If your  
unit is out of warranty, we will quote the  
cost of an exchange unit to you.  
800-283-6503  
(Toll free inside U.S.A.)  
Our toll-free Camcorder number  
operates from 8 a.m. to 5 p.m., CST  
Monday – Friday  
for U.S. customers only  
Returning equipment to Thomson for repair or exchange  
If we are unable to resolve your problem  
over the phone, we will gladly service  
your unit or exchange it for a new or  
refurbished camcorder. Refer to the  
limited warranty on the reverse side to  
learn about your specific rights and  
responsibilities.  
Always consult Thomson and get a  
Return Authorization number before  
returning anything! Obtain a Return  
Authorization (RA) number from the  
telephone representative before returning  
your equipment to avoid delays,  
accounting errors, or even loss of your  
unit.  
Important information to customers who ship defective equipment to  
Thomson Consumer Electronics  
The Thomson representative who  
authorized the return of your equipment  
will give you an RA number over the  
phone. They will also provide you with  
instructions on where and how to return  
your camcorder. Write the number in  
large, clear characters on the outside of  
the box. To avoid confusion and  
and model/serial number of your  
camcorder. These numbers are located  
on the bottom of your unit. If your  
camcorder is within the warranty period,  
please provide a copy of the bill of sale  
to verify purchase date. Use the original  
box and packing material to protect the  
equipment from damage in shipment.  
misunderstandings, shipments without an  
RA number clearly visible on the outside  
of the box will be returned to you at your  
expense.  
For your protection, insure all shipments  
for full replacement value and use a  
reliable shipper. Thomson assumes no  
responsibility for warranty shipments  
from the customer to the factory if not  
shipped in the manner prescribed by  
Thomson.  
Include a brief note describing the  
problem and any conversations about the  
problem you have had with Thomson  
personnel. Include your name, address  
(continued on next page)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
65  
Limited Warranty  
What your warranty covers:  
• Any defect in materials or  
workmanship.  
which validates date of purchase to  
the exchange location and you will be  
provided the new or refurbished unit.  
4. If the repairs were covered by your  
warranty, you will not be billed.  
For how long after your purchase:  
• 90 days for labor charges.  
• One year for parts.  
If you are not located near an exchange  
point:  
What we will do:  
1. Provide your Discover, MasterCard or  
Visa account number and expiration  
date to our phone representative. This  
is for security purposes. If we receive  
your unit including all accessories  
within 14 days from the date you were  
provided a Return Authorization  
number, only items not covered by  
warranty will be charged to your  
account. IF YOUR UNIT  
During the initial 90 days  
• Exchange your camcorder with a new  
or, at our option, a refurbished unit or  
at your option, repair your camcorder  
at no cost to you.  
After the 90 days and within one year  
• Exchange your camcorder with a new  
or, at our option, a refurbished unit or  
at your option, repair your camcorder.  
Parts will be provided at no charge,  
but you will be responsible for the cost  
of labor required for the repair.  
INCLUDING ALL ACCESSORIES  
IS NOT RECEIVED WITHIN 14  
DAYS, THE SUGGESTED  
RETAIL VALUE OF THE  
CAMCORDER AND/OR  
How you get service:  
• Call 1-800-283-6503 and have your  
unit’s date of purchase and  
ACCESSORIES WILL BE  
model/serial number ready. The  
model/serial number information is on  
the bottom of your camcorder.  
CHARGED TO YOUR CREDIT  
CARD. This amount will be credited  
if the unit is subsequently received.  
2. We will send you a replacement unit  
next business day delivery.  
3. You will receive an invoice packed  
with the replacement product, but will  
not be charged for the unit portion of  
the invoice amount if we receive your  
unit including all accessories within  
14 days from the date you were  
provided the RA number. Any labor  
and parts charges not covered by our  
warranty will be included and charged  
against your account.  
• A representative will troubleshoot  
your problem over the phone. If the  
representative determines that you  
should receive a replacement unit, you  
will be provided with a Return  
Authorization (RA) number and the  
location of a nearby exchange point if  
one exists. No returns will be  
accepted without the RA number.  
To receive a replacement camcorder  
before you return yours:  
If you are located near an  
exchange point:  
1. We will send a replacement unit to the  
exchange point next business day  
delivery.  
2. The exchange location will notify you  
of its arrival.  
3. Take your unit, including all  
accessories, and your bill of sale  
4. Ship the unit back to us along with all  
accessories included with your  
camcorder using the replacement  
unit’s carton. Shipping instructions  
will be included in the carton along  
with your RA number, which will  
allow you to easily ship the unit back  
to us. Make sure you insure your  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Warranty  
shipment in case of damage or loss.  
Include with the shipment:  
• A copy of your dated bill of sale to  
verify your unit’s warranty  
eligibility.  
• A brief note describing your  
camcorder problem.  
To have your Camcorder repaired by  
an Authorized RCA Camcorder  
Servicenter:  
• Check with your dealer or call 1-800-  
336-1900 for the Authorized RCA  
Camcorder Servicenter nearest you.  
• Take your unit to the Authorized RCA  
Camcorder Servicenter of your choice.  
• Show the Authorized RCA Camcorder  
Servicenter representative your sales  
receipt or other, evidence of purchase.  
• Pick up your camcorder when repairs  
are complete.  
• Your name, address and phone  
number.  
Return transportation, storage, and  
handling costs and insurance are your  
sole responsibility. We accept no  
liability in case of damage or loss.  
What your warranty does not cover:  
• Adjustment of customer controls.  
• Damage from misuse or neglect.  
• A unit that has been modified or  
incorporated into other products or is  
used for institutional or other  
commercial purposes.  
• Battery for clock and other features.  
• Cleaning of video/audio heads.  
• Camcorders purchased or serviced  
outside the U.S.A.  
• Return transportation, storage and  
handling costs of your unit,  
including insurance for loss or  
damage.  
• Acts of God, such as but not limited to  
lightning damage.  
To receive a replacement unit after we  
have received your unit:  
1. Write the RA number on the outside of  
the carton used to return the unit.  
Make sure you insure your  
shipment in case of damage or loss.  
2. Carefully pack the unit along with all  
accessories included with your  
camcorder, using the original box and  
packing material if possible.  
3. Include with the shipment:  
• A copy of your dated bill of sale to  
verify your unit’s warranty  
eligibility.  
• A brief note describing your  
camcorder problem.  
• Your name, address and phone  
number.  
Product Registration:  
• Please complete and mail the Product  
Registration Card packed with your  
camcorder. It will make it easier to  
contact you should it ever be  
Return transportation, storage, and  
handling costs, and insurance are your  
responsibility. We accept no liability in  
case of damage or loss.  
4. Include a cashier’s check or money  
order for payment if there are any out  
of warranty labor or parts charges  
which were indicated by the  
representative, and you elected not to  
use your credit card.  
5. Upon receipt of your product, a new or  
refurbished unit will be shipped to you  
next day delivery.  
necessary. The return of the card is  
not required for warranty coverage.  
How State Law relates to warranty:  
• This warranty gives you specific legal  
rights and you may have other rights  
that vary from state to state.  
If you purchased your Camcorder  
outside the United States:  
• This warranty does not apply. Contact  
your dealer for warranty information.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
General  
Camera Section  
Power requirement: 9.6VDC  
Power consumption: 8 watts (normal)  
Weight: 4.4 lbs. (2 kg)  
Scanning: 525 Lines/60 Fields/30  
Frames  
Image Sensor: 1/4” high/resolution,  
solid state CCD imager  
Dimensions:  
Tripod Mount: One 1/4" x 20 threaded  
hole  
4-1/2"(W) x 8-1/8"(H) x 12-1/4"(D)  
(111 x 205 x 311mm)  
Lens: f1.6 — 12:1 (4-48mm)  
Diameter: 46 mm  
Video Recorder Section  
Format: VHS  
Adapter/Charger  
Record/Playback System:  
Two video record/playback heads  
One flying erase head  
Power Requirement: 120 V 50/60 Hz  
Power Consumption: 30 Watts (max)  
Weight: (390 grams)  
Headwheel Cylinder Diameter: 62 mm  
Video Signal: EIA Standard NTSC  
Color  
Dimensions:  
(78 x 52 x 155 mm)  
Tripod Mount: One 1  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Information to User  
This equipment has been tested and found to  
comply with the limits for a Class B digital  
device and RF lighting device, pursuant to  
Part 15 and part 18 of the FCC Rules. These  
limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation. This equipment  
generates, uses, and can radiate radio  
• Connect the equipment into an outlet on a  
circuit different from that to which the  
receiver is connected.  
• Consult the dealer or an experienced  
radio/TV technician for help.  
Alterations or modifications carried out  
without appropriate authorization may  
invalidate the user’s FCC right to operate the  
equipment.  
frequency energy and, if not installed and  
used in accordance with the instructions, may  
cause harmful interference to radio  
communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does  
cause harmful interference to radio or  
television reception, which can be determined  
by turning the equipment off and on, the user  
is encouraged to try to correct the interference  
by one or more of the following measures:  
This digital apparatus does not exceed the  
Class B limits for radio noise emissions from  
digital apparatus as set out in the  
interference-causing equipment standard  
entitled “Digital Apparatus”, ICES-003 of the  
Department of Communications.  
Cet appareil numérique respecte les limites  
de bruits radioélectriques applicables aux  
appareils numériques de Classe B prescrites  
dans la norme sur le matériel brouilleur:  
“Appareils Numériques”, NMB-003 édictée  
par le ministre des Communications.  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the  
equipment and receiver.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
— A —  
— C —  
A.(Audio) DUB Indicator . . . . .24,33,35  
A/V DUB Indicator . . . . . . . . . . . . .24,35  
Accessories, Included . . . . . . . . . . . . . .3  
Accessories, Optional . . . . . . . . . .52-59  
Accessory Lens, Attaching . . . . . . . . .55  
Accessory Order Form . . . . . . . . . .57-59  
Adapter/Charger, Using . . . . . . . . . .4,10  
Adjustments and Checks . . . . . . . .62-64  
AE Displays . . . . . . . . . . . . . . . . . .20,24  
AI (Artificial Intelligence) . . . . . . . . .19  
Assistance . . . . . . . . . . . . . . . . . . . . . .65  
Attaching the Adapter/Charger . . . .4,10  
Attaching the Rechargeable Battery . .12  
Attaching the Shoulder Strap . . . . . . .50  
Audio Dubbing . . . . . . . . . . . . . . .32-33  
Audio/Video Dubbing . . . . . . . . . .33,35  
AUDIO/VIDEO Jacks  
Camcorder, Cleaning . . . . . . . . . . . . .61  
Camcorder Operating Controls . . . . .8-9  
Camcorder, Powering . . . . . . . . . .10-15  
Camcorder, Recording On From a  
VCR or TV Monitor . . . . . . . .40-41  
Camcorder, Unpacking . . . . . . . . . . . . .3  
CAMERA/OFF/VCR Switch . .5,7,12,19,  
. . . . .26-27,33,35,36-38,41,42,45,47  
Car Cord, Optional . . . . . . . . . . . . .15,53  
Card, Registration . . . . . . . . . . . . . . . . .i  
Care and Maintenance . . . . . . . . . .60-61  
Care and Storage, Battery . . . . . . . . . .13  
Care and Storage, Cassettes . . . . . . . .17  
Carrying Case, Packing . . . . . . . . . . . .51  
Cassette Door . . . . . . . . . . . . . . . . . .9,17  
Cassette, Inserting and Removing . .6,17  
Cassette Tips . . . . . . . . . . . . . . . . . . . .18  
Cassettes, Video . . . . . . . . . . . . . . .16-17  
Charging the Battery . . . . . . . . . . . . . .11  
Chart of Title Characters . . . . . . . . . . .37  
Checking Battery Power . . . . . . . . . . .14  
Checks and Adjustments . . . . . . . .62-64  
Cleaning the Camcorder . . . . . . . . . . .61  
Clock Battery, Charging . . . . . . . . . . .27  
COLOR Control . . . . . . . . . . . . . . . .9,23  
Color Enhancement Light . . . . . . .48-49  
Contents . . . . . . . . . . . . . . . . . . . . . . .1-2  
Copying Tapes . . . . . . . . . . .40-41,44-45  
Correcting the Date and Time . . . . . . .26  
Customer Assistance .1,3,65,Back Cover  
. . . . .8,32-33,34-35,40-41,44-45,46  
AUTO Date Display . . . . . . . . . . . . . .27  
AV (Audio/Video) OUT/IN Switch  
. . . . .8,32-33,34-35,40-41,44-45,46  
AV DUB Button . . . . . . . . . . .8,25,33,35  
— B —  
Battery, Attaching and Removing . . . .12  
Battery Care and Storage . . . . . . . . . .13  
Battery Charging . . . . . . . . . . . . . . . . .11  
Battery, Clock . . . . . . . . . . . . . . . . . . .27  
BATTERY EJECT Lever . . . . . . . . .8,12  
Battery Level Indicator . . . . . . .14,24-25  
Battery, Rechargeable . . . . . . . . . .11-14  
Battery Safety Precautions . . . . . . . . .13  
BRIGHT Control . . . . . . . . . . . . . . .9,23  
Bulb Replacement,Video Light . . . . .49  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
— D —  
— L —  
Date and Time Displays . . .24-25,26-27  
Date and Time Recording . . . . . . . . . .27  
DATE/TIME Button . . . . . . . .8,25,26-27  
DC IN 9.6V Jack . . . . . . . . . . . . . . . . . .9  
Design Specifications . . . . . . . . . . . . .68  
DISPLAY Button . . . . . . . . . .8,24-25,30  
Dubbing . . . . . . . . . . . . . . . .32-33,34-35  
Lens Hood . . . . . . . . . . . . . . . . . . . .8,55  
Lens Cap Holder . . . . . . . . . . . . . . . . . .9  
Lens Cap, Remove . . . . . . . . . . . . . . . .5  
Lens Hood, Removing . . . . . . . . . . . .55  
Lens, Cleaning . . . . . . . . . . . . . . . . . .61  
LIGHT AUTO/OFF/ON Switch . . . .8,48  
Light Bulb, Replacing . . . . . . . . . . . . .49  
Light, Built-in . . . . . . . . . . . . . . .8,48-49  
Limited Warranty . . . . . . . . . . . . .66-67  
— E —  
— M —  
Edit Search . . . . . . . . . . . . . . . . . . . . .31  
EDIT—ADV Button . . . . . . . . . .8,36-38  
Electronic Indexing . . . . . . . . . . . . . . .21  
Erase Protection . . . . . . . . . . . . . . . . .16  
Eyepiece Focus Control . . . . . . . .6,8,22  
Maintenance and Care . . . . . . . . . .60-61  
Memory Stop Feature . . . . . . . . . . . . .30  
Microphone . . . . . . . . . . . . . . . . . . .8,19  
— F —  
— N —  
F.FWD Button . .8,19,26,30,31,33,35,43  
FADE Button . . . . . . . . . . . . . . .8,24,29  
FADE Indicators . . . . . . . . . . . . . .24,29  
Fading . . . . . . . . . . . . . . . . . . . . . . . .29  
First-Time Operation . . . . . . . . . . . . .3-9  
Flying Erase Head . . . . . . . . . . . . . . . .31  
Focus, Auto and Macro . . . . . . . . . . . .20  
NO TAPE Indicator . . . . . . . . . . . .24-25  
— O —  
OFF/CAMERA/VCR Switch . .5,7,12,19,  
. . . . .26-27,33,35,36-38,41,42,45,47  
Operating Controls, Camcorder . . . . .8-9  
Operation, First-Time . . . . . . . . . . . .3-9  
Optional Accessories . . . . . . . . . . .52-59  
Optional Car Cord . . . . . . . . . . . . .15,53  
Order Form, Accessories . . . . . . . .57-59  
— H —  
Handstrap . . . . . . . . . . . . . . . . . . . . . .5,9  
— I —  
INDEX Indicator . . . . . . . . . . . .21,24-25  
Indexing, Electronic . . . . . . . . . . . . . .21  
Information to User . . . . . . . . . . . . . . .69  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Recording, First . . . . . . . . . . . . . . . . . . .7  
Registration Card . . . . . . . . . . . . . . . . . .i  
Removing Lens Hood . . . . . . . . . . . . .55  
Removing the Rechargeable Battery .12  
Replacing Bulb of Video Light . . . . . .49  
RESET Button . . . . . . . . . . . . . . . . .8,30  
REVIEW Button . . . . . . . . . . . . . . . .8,19  
REW (Rewind) Button  
— P —  
Packing Carry Case . . . . . . . . . . . . . . .51  
PAUSE Indicator . . . . . . . . . . . . . .33,35  
Picture Search . . . . . . . . . . . . . . . . . . .43  
PLAY Button . . . .7,8,31,33,35,42,45,47  
Playback on a TV with  
AUDIO/VIDEO IN Jacks . . . . .44-45  
Playback on a TV  
. . . . . . . . . .7,8,19,26,30,31,33,35,43  
RF DC OUT Jack . . . . . . . . . . . . . . .8,46  
RF Output Adapter . . . . . . . . . .46-47,54  
without Audio/Video Inputs . .46-47  
Playback, First . . . . . . . . . . . . . . . . . . . .7  
Playback, Viewfinder . . . . . . . . . . . . .42  
Plug Adapter, Optional . . . . . . . . . . . .10  
POWER (CAMERA/OFF/VCR)  
— S —  
Switch . . . . . . . . . . .5,7,12,19,26-27  
. . . . . . . . . .33,35,36-38,41,42,45,47  
Power Zoom Buttons . . . . . . . .24-25,28  
Powering Your Camcorder . . . . . .10-15  
Problem Solving . . . . . . . . . . . . . .62-64  
Product Registration . . . . . . . . . . . . . . .i  
ProEdit Features . . . . . . . . . . . . . .31-38  
Program AE (Auto Exposure) . . . . . . .20  
Safety Information . . . . . . . . . . . . . . . . .i  
Safety Precautions, Battery . . . . . . . . .13  
Safety Tab . . . . . . . . . . . . . . . . . . . . . .16  
Set the Date and Time . . . . . . . . . . . . .26  
Shoulder Strap Attachment Rings . .9,50  
Shoulder Strap, Attaching . . . . . . . . . .50  
Solving Problems . . . . . . . . . . . . . .62-64  
SP (Standard Play) Speed . . . . . . . . . .16  
Specifications . . . . . . . . . . . . . . . . . . .68  
Status Displays . . . . . . . . . . . . . . . . . .24  
Stop Action Pause . . . . . . . . . . . . . . . .43  
STOP/EJECT Button  
— Q —  
Quick Review . . . . . . . . . . . . . . . . . . .19  
. . . . . .6,7,8,17,19,26,30,33,35,45,47  
— R —  
— T —  
REC Indicator . . . . . . . . . . . . . . . . . .7,24  
REC/PAUSE Button  
Tab, Safety . . . . . . . . . . . . . . . . . . . . .16  
Table of Contents . . . . . . . . . . . . . . . .1-2  
Tape Copying . . . . . . . . . . .40-41,44-45  
Tape Counter . . . . . . . . . . . . . . . . .24,30  
TAPE END Indicator . . . . . . . . . . .24-25  
TAPE Indicator . . . . . . . . . . . . . . .24-25  
Tape Positioning . . . . . . . . . . . . . . . . .19  
Things to Avoid . . . . . . . . . . . . . . . . .60  
Tilt Adjustment . . . . . . . . . . . . . . . . . .23  
. . . . . . .7,9,29,30,33,35,38,43,45,47  
Rechargeable Battery . . . . . . . . . . .11-14  
Recording Date and Time . . . . . . . . . .27  
Recording on the Camcorder . . . . .40-41  
Recording Speed . . . . . . . . . . . . . . . . .16  
Recording Tips . . . . . . . . . . . . . . . . . .39  
Recording Titles . . . . . . . . . . . . . . . . .38  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Time and Date Display . . . .24-25,26,27  
Time and Date Recording . . . . . . . . . .27  
Time Remaining Display . . . . . . . .21,24  
TINT Control . . . . . . . . . . . . . . . . . .9,23  
Tips, Cassette . . . . . . . . . . . . . . . . . . .18  
Tips, Recording . . . . . . . . . . . . . . . . . .39  
Tips, Traveling . . . . . . . . . . . . . . . . . .18  
TIME/DATE Button . . . . . . . .8,25,26-27  
TITLE SEL + and – Buttons . . . .8,36-38  
TITLE SEL Button . . . . . . . . . . .8,36-38  
TITLER Button . . . . . . . . . . . . . .8,36-38  
Titler . . . . . . . . . . . . . . . . . . . . . . .36-38  
TRACKING (Also Power Zoom)  
— W —  
Warranty, Limited . . . . . . . . . . . . .66-67  
— Z —  
Zoom Buttons . . . . . . . . . . . . . . . . .9,28  
Zoom Level Control . . . . . . . . . . . .24,28  
Zooming . . . . . . . . . . . . . . . . . . . . . . .28  
Buttons . . . . . . . . . . . . . . . . . . .42,43  
Traveling Tips . . . . . . . . . . . . . . . . . . .18  
Tripod, Using . . . . . . . . . . . . . . . . . . .56  
Trouble Checks . . . . . . . . . . . . . . .62-64  
— U —  
Unpacking the Camcorder . . . . . . . . . .3  
User Information . . . . . . . . . . . . . . . . .69  
Using a Tripod . . . . . . . . . . . . . . . . . .56  
Using Adapter/Charger . . . . . . . . . . . .10  
Using the Rechargeable Battery . .11-14  
— V —  
VCR/OFF/CAMERA Switch . .5,7,12,19,  
. . . . .26-27,33,35,36-38,41,42,45,47  
VIDEO/AUDIO  
Jacks . . . . . .8,32-33,34-35,44-45,46  
Video Cassettes . . . . . . . . . . . . . . .16-17  
Video Light . . . . . . . . . . . . . . . . . .48-49  
Viewfinder . . . . . . . . . . .6,8,22-23,42,61  
Viewfinder Playback . . . . . . . . . . . . . .42  
Viewfinder, Cleaning . . . . . . . . . . . . .61  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Need Assistance? We want to help!  
U.S. Consumers:  
Camcorder Exchange Warranty . . . . . .800-283-6503  
Customer Service . . . . . . . . . . . . . . . . .800-336-1900  
Accessories . . . . . . . . . . . . . . . . . . . . .800-338-0376  
Canadian Consumers:  
English . . . . . . . . . . . . . . . . . . . . . . . . .800-522-0338  
French . . . . . . . . . . . . . . . . . . . . . . . . .800-522-0445  
If your camcorder needs service, please  
contact your dealer or the nearest Servicenter  
from the yellow pages. Please do not send  
any products to the Indianapolis address listed  
in this manual or on the carton. This will only  
add delays in service for your product.  
10330 N Meridian Street  
Indianapolis, IN 46290  
©
1995 Thomson Consumer Electronics, Inc.  
®
Trademark(s) Registered  
Marca(s) Registrada(s)  
Printed in Japan  
Part Number 95-CC423-1  
QR12653  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Cordless Telephone 43 3571 User Guide
RCA Camcorder CC6394 User Guide
RCA Dishwasher PSD2220ZBB User Guide
RCA Portable DVD Player DRC6327EC User Guide
Ryobi Trimmer RY26000 User Guide
Salton Waffle Iron WM 1186 User Guide
Samsung Digital Camera AD68 04519A User Guide
Samsung DVR SVR 1620 900 User Guide
Sanus Systems Indoor Furnishings EF20 User Guide
Sanus Systems Indoor Furnishings EFAB II User Guide