Quantum Network Card PX500 Series User Guide

PX500 Series DLTSage™ Tape Security  
Quick Start Guide  
TABLE OF CONTENTS  
Introduction  
0
Introduction.......................................1  
Creating a Secure User ......................1  
Creating a Secure Key........................2  
The PX500 Series (PX502, PX506, and PX510) tape libraries with DLT-S4 tape drives  
are capable of utilizing DLTSage Tape security. DLTSage Tape Security is a unique  
solution designed to prevent unauthorized access to tape cartridges which is  
particularly valuable when protecting tapes that are transported offsite. DLTSage  
Tape Security is a firmware feature designed into the DLT-S4 tape drive which uses  
an electronic key to prevent or allow reading and writing of data on to a tape  
cartridge. This key is managed through the remote management pages of the  
PX500 Series tape library (refer to the Quantum PX500 Series User’s Guide, PN 81-  
81290 located on the PX500 Series Documentation CD for more information on  
the remote management pages). DLTSage Tape Security is available at no  
additional cost as an integrated feature in of the DLT-S4 tape drive and PX500  
Series tape library (firmware version 20 or later).  
Enable/Disable Secure Key for  
Drives...............................................4  
Pair...................................................4  
Backup Secure Key File ...................5  
Upload Secure Key File ...................6  
Secure Key Maintenance ...................6  
Notational Conventions  
0
This instruction uses the following conventions:  
NOTE: Notes emphasize important information related to the main topic.  
CAUTION: Cautions indicate potential hazards to equipment and are included  
to prevent damage to equipment.  
WARNING: Warnings indicate potential hazards to personal safety and are  
included to prevent injury.  
Setting up your PX500 Series tape library with DLTSage Tape Security consists of  
the following steps:  
Creating a Secure User  
0
CAUTION: If the Secure Key information is lost, any tape cartridges that were  
secured with the lost key will be unavailable for reading or writing.  
The Secure User is the only user that has the ability to create, modify, and delete a  
Secure Key for the Library. The Secure User also has the ability to enable and  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
PX500 Series DLTSage™ Tape Security Quick Start Guide  
The Secure Key page is divided into the following sections:  
Figure 3 Secure Key Page  
Protection Mode for  
Cartridges  
0
Refer to figure 4 for information on Protection Mode for  
Cartridges.  
Figure 4 Protection Mode for  
Cartridges  
The Protection Mode for Cartridges area defines when the  
Secure Key is used for a cartridge in a tape drive with a  
Secure Key enabled. In all modes, the Secure Key is used to  
read data from cartridges that have a pre-existing Secure  
Key. If the Secure Key on the cartridge does not match the  
current Secure Key on the library, the data on the cartridge  
can not be read.  
Three write protection modes are available:  
Never Write Secure Key to a Cartridge - The Secure  
Key will never be written to a cartridge placed in a  
secured tape drive.  
Only Write Secure Key to Blank Cartridges - The  
Secure Key will only be written to blank, unformatted  
cartridges.  
Write Secure Key to All Cartridges - The Secure Key  
will be written to all cartridges, including blank and  
formatted cartridges containing data. This mode may  
be used to apply a Secure Key to cartridges with pre-  
existing data.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
PX500 Series DLTSage™ Tape Security Quick Start Guide  
1 Select the Secure Key name from the list of available  
Enable/Disable Secure Key  
for Drives  
names.  
0
NOTE: Selecting None to will cause the library to  
Refer to figure 5 for information on Enable/Disable Secure  
NOT use a Secure Key.  
Key for Drives.  
Figure 5 Enable/Disable Secure  
Key for Drives  
2 Click Update.  
NOTE: The system must be offline to modify a  
Secure Key.  
Assign Secure Key to  
Cartridge  
0
Refer to figure 7 for information on Assign Secure Key to  
Cartridge.  
The Secure Key can only be used with tape drives that are  
Secure Key capable. This section lists the tape drives in the  
library that are Secure Key capable. A checkmark in the  
Secure Key column indicates a Secure Key is enabled for  
the tape drive.  
Figure 7 Assign Secure Key to  
Cartridge  
1 The Secure Key can be enabled or disabled for all tape  
drives by clicking the corresponding radio button.  
2 Click the Secure Key check box for individual tape  
drives to enable/disable Secure Key for a tape drive.  
3 Click Update to activate the changes.  
NOTE: The system must be offline to Enable/Disable  
Secure Key setting for drives.  
Click Find to list all secured cartridges and their assigned  
Secure Key names.  
Modify Secure Key for  
Library  
0
To assign a Secure Key to a cartridge:  
Refer to figure 6 for information on Modify Secure Key for  
Library.  
1 Enter the barcode of the cartridge. Separate multiple  
barcodes with either spaces or commas.  
2 Select a Secure Key name from the list of available  
Figure 6 Modify Secure Key for  
Library  
names.  
3 Selecting Remove will remove the association between  
the cartridge and a Secure Key name in the cartridge  
database.  
4 Click Update to accept the changes.  
Create Secure Key Name/  
Secure Key Pair  
0
Refer to figure 8 for information on Create Secure Key  
Name/Secure Key Pair.  
To modify the Secure Key used by the library:  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
PX500 Series DLTSage™ Tape Security Quick Start Guide  
Unused Secure Keys - keys not associated with any  
cartridges or tape drives currently in the system.  
Figure 8 Create Secure Key  
Name/Secure Key Pair  
Inactive Secure Keys - keys associated with cartridges  
in the library, or currently assigned to the library, but  
not assigned to any tape drives.  
Active Secure Keys - keys currently assigned to a tape  
drive.  
To delete a Secure Key Name/Secure Key pair from the  
library:  
1 Select the desired Secure Key Names from the  
available lists.  
To create a secure key name/secure key pair:  
2 Click Delete.  
1 Enter the Secure Key Name.  
A confirmation message will be displayed, click Yes to  
continue.  
NOTE: The Secure Key name must be less than 12  
characters, may include spaces, but cannot  
contain the following characters: ( ) = ;  
Any tape drives that have been Secure Key enabled will  
remain enabled, but the Secure Key will not be used to  
read or write cartridges.  
2 Enter a securekey in the protected Secure Key field.  
3 Enter the same Secure Key in the Verify Secure Key  
Backup Secure Key File  
0
field.  
Refer to figure 10 for information on Backup Secure Key  
File.  
NOTE: The Secure Key must be at least 8 characters  
and no more than 32 characters.  
Figure 10 Backup Secure Key File  
4 Click New to create the Secure Key name/key pair.  
Delete Secure Key Name  
0
Refer to figure 9 for information on Delete Secure Key  
Name.  
Figure 9 Delete Secure Key Name  
The list of Secure Key Name/Secure Key Pairs maintained  
on the library should be backed up to a local device  
whenever a change is made to the security keys.  
NOTE: Note the library's Encryption Key. The Encryption  
Key is required when restoring the file to any  
library.  
1 Click Save As...  
2 From the browser's Save window, select a path and  
name the file.  
3 Click OK.  
The Secure Key Names maintained on the library are  
displayed in one of three lists:  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
PX500 Series DLTSage™ Tape Security Quick Start Guide  
Upload Secure Key File  
0
Importing Secured Tape Cartridges  
0
Refer to figure 11 for information on Upload Secure Key  
File.  
If you need to import tape cartridges into your library which  
have been secured with a key from another PX500 Series  
library, you need to import the Secure Key before the library  
can read or write to the tape cartridges.  
Figure 11 Upload Secure Key File  
To import secured tapes:  
1 Write down the barcodes for every secured tape that  
will be imported into the library. You will need to have  
these barcodes available when associating the tape  
cartridges with the Secure Key.  
2 Insert the tape cartridges into the PX500 Series library  
(refer to the PX500 Series User’s Guide (PN 81-81290)  
for information on inserting tape cartridges.  
A file containing a list of Secure Key Name/Secure Key  
Pairs can be restored to the library.  
3 On the PX500 Series library where the tape cartridges  
were originally secured with a key, backup the specific  
Secure Key associated with those tape cartridges (see  
NOTE: The Encryption Key of the library originally  
maintaining the list is required to restore the file.  
4 Upload the Secure Key from the original library to the  
where the tape cartridges were imported (see Upload  
To upload (restore) a Secure Key File:  
1 Enter the Encryption Key of the original library.  
2 Enter the path and file name of the file to be uploaded  
5 Assign the barcode labels from the imported tape  
cartridges with the Secure Key from the original library  
(click Browse...)  
3 Click Upload button.  
The imported tape cartridges are now associated with  
the Secure Key.  
A progress window is displayed indicating when the  
upload is complete or if any errors occurred during the  
upload or restoration of the file.  
The Secure Key page is refreshed listing restored  
secure keys.  
Secure Key Maintenance  
0
Quantum strongly recommends that you backup your secure  
keys whenever a new key is added (see Backup Secure Key  
File). The location of these keys should be available to library  
administrators who need access to secured tape cartridges.  
NOTE: An error is displayed if the serial number provided  
does not match the serial number used to encode  
the secure keys.  
CAUTION: If the Secure Key information is lost, any  
tape cartridges that were secured with the  
lost key will be unavailable for reading or  
writing.  
United States of America  
Quantum Corporation  
141 Innovation Drive  
Irvine, CA 92612  
U.S.A.  
phone 949.856.7800  
fax 949.856.7799  
European Headquarters  
Asia Pacific  
Quantum Corporaton  
3 Bracknell Beeches  
Old Bracknell Lane West  
Bracknell  
Berkshire RG12 7BW  
United Kingdom  
Quantum Corporation  
9 Temasek Boulevard, #08-03  
Suntec Tower Two  
Singapore 038989  
Tel: +65 6334 0660  
Fax: +65 6432 2830  
phone +44 1344 353500  
fax +44 1344 353510  
©2006 Quantum Corporation. Quantum, the Quantum logo, and the DLTtape logo are all registered trademarks of Quantum Corporation. SDLT and Super DLTtape are trademarks of  
Quantum Corporation. Other trademarks may be mentioned herein which belong to other companies.  
81-81627-01 A01 June 2006  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       

PYLE Audio Stereo Amplifier PZR1000 User Guide
Raypak Ventilation Hood 181 182 User Guide
Reebok Fitness Treadmill RBTL11982 User Guide
Remington Trimmer ST3812B, ST4514B User Guide
Ricoh Thermostat EK 182 40930 User Guide
Samsung Air Conditioner AS07A5A6MA User Guide
Sanyo Air Conditioner C0971 User Guide
Sanyo Battery Charger UF103450P User Guide
Scytek electronic Remote Starter 100RS User Guide
SEAL Laminator 44 62 User Guide