Pulsar Frozen Dessert Maker EME User Manual

WSJT 4.6 User’s Guide

WSJT is a computer program for VHF/UHF communication using state of the art digital

techniques. It can decode signals propagated by fraction-of-a-second reflections from

meteor trails, as well as steady signals 10 to 20 dB weaker than those needed for

conventional CW or SSB.

Operating Modes

• FSK441 for high speed meteor scatter

• JT6M for meteor/ionospheric scatter on 6 meters

• JT65 for extremely weak troposcatter and EME

• EME Echo for detecting your own echoes from the moon

System Requirements

• SSB transceiver and antenna for one or more VHF/UHF bands

• Computer running Microsoft Windows

• 200 MHz or faster CPU

• 32 MB of available RAM

• Monitor with 800 x 600 or higher resolution

• Windows compatible sound card

• Computer-to-radio interface using a serial port to key your PTT line (or use VOX)

• Audio connections between transceiver and sound card

• A means for synchronizing the computer’s clock to UTC

Quick-Start Installation and Setup

1. Download WSJT from http://pulsar.princeton.edu/~joe/K1J Tor the European

mirror site, http://www.vhfdx.de.

2. Execute the downloaded file to install WSJT to a directory of your choice.

3. If you have not already done so, print a copy of this manual and keep it handy.

4. Connect appropriate interface cables between your computer and radio. (For help with

the hardware interface, refer to one of the many descriptions of other sound card modes

such as PSK31.)

5. To start the program, double-click on the desktop icon for WSJT.

6. Select Options from the Setup menu (see picture on next page) and enter your callsign,

grid locator, and UTC offset. Click Done to dismiss the Options screen.

7. Select Setup | Set COM Port and enter the number of the serial port you will use for

T/R control. Enter 0 if you will use VOX control.

8. Indicate on the Setup menu whether you wish to use the DTR or RTS line for PTT

control. (If not sure, check both.)

These settings should be adequate for learning your way around the program. If you are

new to WSJT, work through the examples at the top of page 3 and then continue reading

this manual, stopping to experiment with the program when it seems appropriate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Example Files

To gain some familiarity with the operation of WSJT, use the program to decode some

example files provided with the standard installation. Hit function key F7 to choose

FSK441A mode, and select Open from the File menu. Navigate to the RxWav\Samples

folder in your WSJT home directory and open the file recorded from W8WN. When this

file has been decoded, the top of your screen should look like the picture on page 2. With a

speaker or headphones connected to the soundcard output, listen to the recording by clicking

the Play button. You will hear static crashes at the beginning of the file and a moderately

strong ping from W8WN about 18 seconds later. Try clicking around the ping with both left

and right mouse buttons, and observe the decoded text that appears. Click the Big

Spectrum button to see what these signals look like on the large waterfall display. Click

Erase on the main screen to clear the text and graphical areas.

Next, select JT6M from the Mode menu and open the sample file from AF4O. Nothing

decodes automatically in this file—the signal is very weak—but try right-clicking on the

green line at about t = 12.9 s, as displayed on the green label at lower left of the plot area.

You will find that AF4O was calling K1JT. Try listening to this file: the signal is audible

some of the time, but only barely. Finally, switch to JT65A mode and open the recording

from OH7PI. The graphics window and decoded text boxes on your screen should look like

the picture on page 5. Listening to this file, you will hear only random noise. OH7PI’s 144

MHz EME signal was much too weak for CW communication at this time, but he was solid

copy in JT65.

Adjusting Signal Levels

1. Turn on your radio and tune it to a clear frequency so that only background noise is sent

to the sound card.

2. Press F9 to select the EME Echo mode.

3. Select Setup | Adjust RX Volume control to bring up the sound card input mixer.

4. Click Measure to start a sequence of noise measurements

5. Adjust a slider on the audio mixer and/or your receiver gain control(s) so as to bring the

signal level close to what WSJT calls “0 dB”. The signal level is displayed numerically

and illustrated by a green line in the plot area. The green curve should be approximately

aligned with tick marks on the left and right border.

6. Press F7 to enter FSK441A mode.

7. Click Record to start a receiving period. The program will record noise for 30 seconds

and then attempt to decode it. This should produce a jagged green line in the large plot

area, along with a waterfall-style spectrogram. The green line is a graph of received

noise power vs. time. The waterfall is a time vs. frequency spectrogram in which

frequency increases upward, time to the right.

8. Select Setup | Adjust TX Volume control to bring up the sound card output mixer.

9. Turn off your final amplifier (if any). Click one of the four Tune buttons A, B, C, or D

to be sure that T/R switching works and an audio tone is sent from the computer to your

radio.

10. Adjust the slider on the audio mixer to get the proper audio signal level for your

transmitter. Watch the transmitter power output while sending each of the four tones A,

B, C, and D. Variations of 10% or even 20% among the four tones are acceptable, but

50% differences will degrade your signal. You may find it useful to experiment with the

setting of a speech processor or ALC control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operating Instructions

Note: further details on commands in boldface may be found in the alphabetical list starting

on page 15.

WSJT uses timed intervals of transmission and reception. By convention FSK441 and

JT6M use 30 s periods, while JT65 always uses 60 s intervals. To prepare for making a

QSO, enter the other station’s callsign in the To radio box and click Lookup and Gen Std

Msgs to generate a sequence of commonly used messages. If Lookup does not find the

callsign in the database file CALLSIGN.TXT, you may enter the grid locator manually.

Decide whether you or the other station will transmit first, and check or uncheck TX First

appropriately. Click Auto to start an automatic sequence of transmission and reception

intervals.

At the end of each receiving period, WSJT displays various properties of a received signal

graphically. A green line illustrates signal strength vs. time, and other lines or images

display spectral information and synchronization results, depending on the mode. Decoded

text appears in the large box near center screen. Refer to the pictures on pages 2, 4, and 5

for examples in the FSK441, JT6M, and JT65 modes.

When an FSK441 or JT6M reception period has finished the program looks for signal

enhancements produced by short-lived reflections from meteor trails. You can often hear

such “pings” when they occur, and they can be seen as spikes on the green line and brighter

colors in the waterfall spectrum. One or more lines of decoded text may result from each

ping. By clicking on the green line with the mouse, you can force decoding of a particular

spot in a record.

WSJT attempts to compensate for relative mistuning between transmitting and receiving

stations. By default the frequency search range is ±400 Hz (±600 Hz in JT65). You can

reduce the range by setting the value of Tol (for “tolerance”) to a lower value. Several other

decoding parameters can be adjusted, as well. In FSK441 mode W sets the minimum width

and S the minimum strength (in dB) for acceptable pings. Adjustments can be made at any

time by clicking on spinner controls next to the parameter labels, and all parameters can be

reset to default values by clicking the Defaults button.

JT6M

mode

In addition to the green line for overall signal strength, JT6M produces a yellow line

showing the detected strength of a synchronizing tone. JT6M attempts to decode both

individual pings and an “average message” based on the entire transmission (or selected

portions thereof). An average message is flagged with an asterisk at the right end of the text

line. Clicking with the left mouse button decodes a 4 s block of data near the mouse pointer,

while the right button decodes a 10 s segment. You can also drag the mouse pointer with the

Download from Www.Somanuals.com. All Manuals Search And Download.

button down to select any desired region. As in FSK441, with marginal signals you should

experiment as necessary for best decoding. JT6M can work with signals many dB weaker

than those required for FSK441. You will sometimes find that clicking on a smooth green

line, even where nothing was heard and nothing can be seen, causes callsigns or other

information to pop up out of the noise.

Time synchronization

Sync tone detected

at DT = 1.9 s

at DF=43 Hz

(blue line)

(red line)

DF: –600

DT: –1

T: 0

–400

–200

200

400

600 Hz

5 s

60 s

Graphics Window

Sun/Moon

Data

Decoded Text Box

Average

Text Box

TX Messages

Main Screen

JT65A mode

JT65 requires tight synchronization between transmitter and receiver, so in this mode the

only way to initiate a transmission or reception interval is by toggling Auto to ON. As in

other WSJT modes, an incoming signal is analyzed after a full receiving sequence is

complete. The resulting graphical display includes red and blue lines along with the green

line. The additional curves summarize the program’s attempts to synchronize with the

Download from Www.Somanuals.com. All Manuals Search And Download.

received signal, a necessary step toward decoding the message. Proper synchronization is

indicated by a sharp upward spike in the red curve and a broader peak on the blue curve.

Horizontal locations of the peaks correspond to the frequency and time offsets, DF and DT,

between transmitter and receiver. EME QSOs have propagation delays of about 2.5 s and

can have significant Doppler shifts. Along with clock and frequency errors, these effects

contribute to the measured values of DT and DF.

Message Formats

Standard messages in FSK441 and JT6M are generated with the aid of templates defined on

the Setup | Options screen (see p. 2). Default templates are provided conforming to

standard practice in North America and Europe, and you can edit the templates to suit your

own requirements. Normal FSK441 and JT6M messages can contain any arbitrary text up

to 28 characters. The supported character set is

0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ.,/#?$ plus the space character.

FSK441 provides a special shorthand format to transmit a few simple messages in a highly

efficient way. Check Sh Msg to activate shorthand messages. The supported messages are

R26, R27, RRR, and 73. FSK441A sends pure tones at 882, 1323, 1764, or 2205 Hz to

convey them, while FSK441B and C use alternating two-tone sequences with the lower tone

at 861 Hz and the upper at 1206, 1550, 1895, or 2240 Hz.

JT65 messages are more constrained and must have one of three basic formats:

1. Four alphanumeric fields with specific contents as described below.

2. Any arbitrary text, up to 13 characters

3. Special shorthand messages ATT, RO, RRR, and 73

The four fields of a type 1 message usually consist of two legal callsigns, an optional grid

locator, and the optional signal report OOO. CQ or QRZ can be substituted for the first

callsign, and CQ may be followed by a space and three digits to indicate a desired callback

frequency. If K1JT transmits on 144.140 and sends “CQ 113 K1JT FN20”, it means that he

will listen on 144.113 and respond there to any replies. A country prefix preceded by “/” or

a signal report of the form “–NN” or “R–NN” may be substituted for the grid locator. For

example, –24 might indicate that signals were received at –24 dB. The minus sign is

required, and NN must lie between 01 and 30. A list of supported country prefixes is given

in Appendix A. The following are all examples of legal messages of type 1:

F9HS K1JT

F9HS K1JT FN20

F9HS K1JT /KP4

K1JT VK7MO R–26

CQ 113 K1JT

F9HS K1JT FN20 OOO

F9HS K1JT /KP4 OOO

CQ K1JT

F9HS K1JT OOO

VK7MO K1JT –24

CQ K1JT FN20

QRZ K1JT

CQ 113 K1JT FN20

QRZ K1JT FN20

The JT65 shorthand messages are powerful because they can be decoded at signal levels

some 5 dB below those required for standard messages. They do not use tight time

synchronization, so they provide no information on DT. The ATT message (for

“Attention”) is intended to help two stations find each other before a normal QSO begins. If

a message starts with ATT, RO, RRR, or 73, the shorthand format will be sent. If it satisfies

the requirements for message type 1, the full message of up to 22 characters will be

compressed and sent. With any other entry, 13 characters of arbitrary text will be sent.

Download from Www.Somanuals.com. All Manuals Search And Download.

Standard QSO Procedures

Difficult contacts become easier if you follow standard operating practices. For minimal

QSOs, the recommended procedure is as follows:

1. If you have received less than both calls from the other station, send both calls.

2. If you have received both calls, send both calls and a signal report.

3. If you have received both calls and a report, send R plus your signal report.

4. If you have received R plus signal report, send RRR.

5. If you have received RRR — that is, a definite acknowledgment of all of your

information — the QSO is officially complete. However, the other station may not

know this, so it is conventional to send 73s (or some other conversational

information) to signify that you are done.

Slightly different procedures may be used in different parts of the world, or in the different

operating modes. Typing the F5 key will cause WSJT to pop up a screen that reminds you

of the recommended procedures.

Select the message for your next transmission by clicking in the small circle to the right of

the message text. In the FSK441 and JT6M modes, and for shorthand messages in JT65,

you can switch messages while a transmission is in progress by clicking on one of the TX

buttons to the right of the circles.

Operating Hints

After every decoding attempt, WSJT displays its best estimate of a detected signal’s

frequency offset. The accuracy of these estimates is approximately ±25 Hz for FSK441

signals, ±10 Hz for JT6M, and ±3 Hz for JT65. Within these tolerances (and subject to the

stability of oscillators and the propagation path) you should see consistent numbers in the

DF column during any QSO producing usable signals.

In the FSK441 and JT6M modes, if DF lies outside the range ±100 Hz it will help to retune

your receiver to compensate. Do this with the RIT control, or by using split RX/TX VFOs.

In general you should not change your transmitting frequency during a QSO, since your

partner will be trying to tune you in at the same time.

JT65 is tolerant of frequency offsets up to ±600 Hz, and unless the “red spike” is close to

one edge of the plot area (see picture on p. 5), retuning with RIT is optional. However, note

that EME QSOs on bands above 432 MHz can have Doppler shifts of several kHz or more.

In such cases you will certainly need to use RIT or split VFOs in order to acquire the

received signal. Once the program has synchronized on a JT65 signal, it’s best to click on

the red spike, check Freeze, and reduce Tol to 100 Hz or less. In subsequent decodings,

WSJT will search a range of frequencies only ±Tol Hz around the DF selected by clicking

on the red spike.

Question marks in displayed JT65 text lines indicate “OOO” and shorthand messages about

which there could be some doubt. These occur when the OOO flag has apparently been

found but the full message text not decoded, or when a probable shorthand message is

detected but you have not yet checked Freeze and reduced Tol to 100 Hz or less. Operator

skill is required in order to make the best possible use of JT65 shorthand messages. Visual

aids to decoding shorthand messages “by eye” are provided if you click on the sync-tone

frequency in the Big Spectrum display.

Download from Www.Somanuals.com. All Manuals Search And Download.

You will need a method of setting your computer clock to an accuracy of one second or

better, and keeping it set. Many operators use an internet clock-setting program, while

others use a GPS or WWVB receiver.

Solar and Lunar Data

The light blue text box in JT65 and EME Echo mode presents data for tracking the moon,

measuring sun noise, tuning your receiver, and evaluating EME path losses. The information

includes azimuth and elevation (Az and El) for the sun and those quantities plus right

ascension (RA), declination (Dec), and local hour angle (LHA) for the moon. All

coordinates are in degrees except for RA, which is given in hours and minutes. The moon’s

semi-diameter (SD) is given in arc minutes, and Doppler shift for the band in use in Hz.

Since two-way Doppler shift depends on the other station’s location as well as your own, the

Doppler field is blank if the Grid box is empty. In EME Echo mode, the displayed

Doppler is your own self-echo value. Tsky gives the galactic background temperature in

the direction of the moon, scaled to the operating frequency, and dB the added signal loss at

the moon’s present distance, relative to perigee. Dgrd is an estimate of the total signal

degradation in dB, relative to the best possible time when the moon is at perigee and in a

cold part of the sky. Click with the mouse anywhere in the light blue text box to see the

local coordinates (Az and El) of the moon at the DX station’s location and the maximum

non-reciprocity of the EME path, in dB. Click again to toggle back to the normal display.

Distinctions between the Submodes

Messages are encoded differently in the three FSK441 submodes, so a transmission in one

mode must be decoded using the same mode. FSK441A uses a zero-redundancy code in

which characters are transmitted with three successive tones, each at one of four assigned

frequencies. The FSK441B and C modes use sequences of four and seven tones,

respectively, with the additional information providing error-correcting capabilities.

FSK441B can correct any single error in the four symbols that make up a character, while

FSK441C can correct up to three errors in seven symbols.

JT65 transmits messages using 65-tone frequency-shift keying at 2.7 baud. The lowest tone

at 1270.5 Hz is used to establish time and frequency synchronization; it is switched on for

half of the time, according to a pseudo-random on-off pattern. The remaining tone intervals

carry the user message, using a Reed-Solomon code for forward error correction. The three

JT65 submodes all use the same code and modulation scheme, but the spacing between

tones is different—approximately 2.7, 5.4, and 10.7 Hz for modes A, B, and C, respectively.

A transmission in one submode must be received in the same submode. If the equipment

and propagation path are stable enough that the measured width of the sync tone is

consistently 4 Hz or less, JT65A will be about 1 dB more sensitive than mode B and 2 dB

more sensitive than C.

Shorthand JT65 transmissions consist of alternating tones, each lasting 1.486 s. The lower

of the two frequencies is always at the sync-tone frequency, 1270.5 Hz, and the separation

between tones is given in the following table:

Message

JT65A

JT65B

JT65C

ATT

RRR

26.9 Hz

53.8

80.8

53.8

107.7 Hz

161.5

107.7 Hz

215.3

323.0

107.7

215.3

430.7

Download from Www.Somanuals.com. All Manuals Search And Download.

EME Echo Mode

EME Echo mode (see picture on next page) is designed to help evaluate the performance of

your station for moonbounce communications. Activate it from the Mode menu or by

pressing function key F9. Aim your antenna at the moon, pick a clear frequency, and toggle

the Auto button to ON. The program will then start cycling through the following loop:

1. Transmit a fixed tone for 2.0 s

2. Wait about 0.5 s for start of return echo

3. Record the received signal for 2.0 s

4. Analyze, average, and plot the results

5. Repeat from step 1

At the start of each transmission the frequency of the transmitted tone is offset randomly

around a nominal value of 1500 Hz. A number in the text box labeled Dither (Hz) controls

the magnitude of the random offset. The observed spectrum of each echo is shifted by the

dither amount before being accumulated into the average. This procedure is very effective

in minimizing the impact of birdies in the receiver passband. In the average spectrum, a

fixed-frequency birdie is smeared out over a wide range while the desired signal remains

sharply defined.

EME Echo mode

Two curves appear in the graphical area after each T/R cycle, each one representing the

spectrum of received power over a 400 Hz range, centered on the expected echo frequency.

The blue (lower) curve is a reference spectrum that you can use to be sure you have chosen a

birdie-free passband. It is aligned to remove the Doppler shift computed at the start of the

run and not subsequently adjusted for changes in Doppler or the programmed dithering of

transmitted frequency. Stable birdies therefore stay fixed in the blue curve, making them

easy to recognize. The red curve displays the average echo signal, adjusted to correct for

changing Doppler shift and for the programmed frequency dithering. Your echo should

appear as a narrow spike near the middle of the red curve, close to DF = 0.

Download from Www.Somanuals.com. All Manuals Search And Download.

Information in the text box gives the number N of completed echo cycles, the average Level

of receiver background noise in dB, the average echo strength Sig in dB, its measured

frequency offset DF in Hz (after correction for Doppler shift), its spectral Width in Hz, and

a relative quality indicator Q on a 0–10 scale. Background noise level is given with respect

to the nominal “0 dB” level used for all WSJT modes. Signal strength is measured in dB

relative to the noise power in the full receiver passband, nominally 2500 Hz. Q = 0 means

that an echo has not been detected or is very unreliable, in which case the values of DF and

Width are meaningless and Sig is an upper limit. Larger values of Q imply increasingly

believable echo measurements. If you can hear your own lunar echoes, you will see a large

spike in the red curve within a few seconds after toggling Auto ON. If your echoes are 15

to 20 dB below the audible threshold you should see a significant spike on the red curve

within a few minutes.

By default EME Echo mode assumes that your receiver and transmitter are tuned to the

same frequency. An on-screen box labeled RIT (Hz) allows you to inform the program of

any offset receiver tuning, for example to accommodate a large Doppler shift. Suppose you

are running a test on 23 cm and the predicted Doppler shift at the start of the run is –1400

Hz. In that case the 1500 Hz transmitted audio tone would be detected at 100 Hz, probably

well below the low-frequency cutoff in your receiver's passband. Use your transceiver's RIT

control to offset the receiver tuning by the predicted Doppler shift or a nearby rounded

value, and enter this offset in the RIT box before starting the echo measurement. The

program will track subsequent Doppler changes up to about 800 Hz, if necessary, without

any further adjustments. Your echo should appear near the center of the red curve, as usual.

You won't need to use the RIT feature on 6 or 2 meters, where Doppler shifts are much

smaller and echoes always fall within the transceiver's SSB passband.

The frequency of a valid echo should be well defined and stable. If you click Clear Avg to

start a new measurement, the echo signal (the red spike) should build up again at the same

DF. To be absolutely sure that you are seeing you own echo, offset your transmitter

frequency by a known amount, say 50 Hz, while holding the receiver frequency constant. A

valid echo will shift by the same 50 Hz.

Measure Mode

A button labeled Measure provides a means for measuring relative noise power from your

receiver. Click it and your system will record audio for one second, compute the level of

noise power, and display the result in dB relative to WSJT’s standard level. This cycle is

repeated every 2 seconds, with the results plotted as a green line and summary data

displayed in the large text box.

If the file DECODED.CUM has been activated from the File menu, data will be written into

that file as well, tagged with the Modified Julian Date on which you made the

measurements. You can use this mode to measure sun noise, antenna temperature, ground

noise, preamp gain, and a host of other useful quantities relative to a chosen reference level.

Be sure to disable the receiver AGC if you intend to use the mode for quantitative

measurements. It would also be wise to make some test measurements (for example, using a

calibrated attenuator) to confirm that the reported dB readings are reliable in your system as

configured.

Download from Www.Somanuals.com. All Manuals Search And Download.

Measure mode, with

preamp turned

on and off repeatedly

EME Calc

Clicking the button labeled EME Calc at the lower left of the Echo-mode screen will pop up

a utility program for predicting the strength of your echoes from the moon. Enter the

requested quantities for your station and click Compute; if you enter parameters for a DX

station as well, you will see the maximum strengths for both station’s self-echoes and for

each signal at the other location. Clicking Now will enter the frequency of the active band

as specified on the Setup | Options form, and the sky background temperature at that

frequency. You can Save a set of parameters to a file, and Load a saved parameter set at

some later time.

EME Calc

Predicted echo strengths assume that your specified parameters are reliable, everything is

working right, and Faraday rotation is cooperating (if relevant). There are many reasons

why your actual echo strength at a given time may be less than the predicted value—and a

few reasons why it might (briefly) be slightly greater.

Amplifier Considerations

WSJT sends a single-frequency sine wave at any instant when it is transmitting. Except

during station identification, there is no “key up” time; signal amplitude is constant, and one

tone changes to the next one in a phase-continuous manner. As a result, WSJT does not

require a high degree of linearity in your power amplifier. You can use a class C amplifier

without generating unwanted sidebands or splatter. Please note that full amplitude

Download from Www.Somanuals.com. All Manuals Search And Download.

transmissions lasting 30 seconds or longer will put more stress on your final amplifier than

SSB or CW operation. If this would cause the amplifier to overheat, you should take

appropriate action: reduce power or add another cooling fan or blower.

Menus and the Setup | Options Screen

File

Open: read and decode a previously recorded file stored on disk. The file must be a

standard wave file recorded in 8-bit monaural format with 11025 Hz sampling.

Open Next in Directory: read and decode the next file after one already opened.

Decode All Files in Directory: sequentially read and decode all wave files following

the one already opened.

Delete files in RxWav: delete all *.WAVfiles in the RxWavsubdirectory.

Save text in file DECODED.CUM: append decoded text to a file named

DECODED.CUMin the WSJT installation directory.

Delete file DECODED.CUM: erase the cumulative text file.

Exit: terminate the program

Setup | Options (see screen picture on p. 2)

My call: Enter your callsign

Grid locator: Enter your 6-digit grid locator

UTC offset: your timezone offset from UTC, in hours. Enter a negative value if you are

east of Greenwich.

RX delay: enforce specified delay between end of transmission and start of next

recording.

TX delay: enforce specified delay between activation of PTT line and start of first audio

tone sent to transmitter.

ID Interval: set time in minutes between automatic station identifications. A value of

zero disables the automatic identification. To use this feature you must provide an audio

file named ID.WAVin the WSJT home directory. The file can identify your station

using any desired mode, e.g., voice or CW. (See Generate ID.WAV).

Download from Www.Somanuals.com. All Manuals Search And Download.

NA/EU Defaults: insert default templates for generating standard FSK441 and JT6M

messages. The templates can be edited, for example to append a suffix or prefix to a

callsign, or to properly format a contest exchange. For example, if G4FDX changes the

template for message TX1 to read “%T W9/%M”, the message “K1JT W9/G4FDX” will

appear in the box for TX message 1 when he presses Gen Std Msgs to call K1JT.

FSK441 Amplitudes: set relative voltage to be generated for each FSK441 tone. If

necessary, one or more of these numbers can be decreased from the nominal 1.0 to

compensate for nonuniform frequency response in your TX audio system.

Audio output: select which audio channel carries signal from the sound card to the

radio: Left, Right, or Both.

Freq MHz: nominal frequency in MHz, used for computing Doppler shifts and sky

background temperatures. (See also Band menu.)

T/R Period: set length of T/R intervals for FSK441 and JT6M modes, in seconds.

Fast CPU: decode JT65 signals immediately after a recording has finished. Check this

box only if your computer is fast enough to allow decoding in 5 seconds or less. It

permits you to see a decoded message before your next transmission begins.

No Sh: disable all decoding of shorthand messages in FSK441.

Other Setup Items

Set COM port: set number of the COM port that will activate T/R switching. To

disable COM port T/R switching, enter 0.

Generate ID.WAV: create a CW wave file in the WSJT home directory with “My call”

sent at 25 WPM, 440 Hz.

DTR, RTS: select the serial-port signal line that will control your T/R switching

sequence.

Adjust RX/TX Volume controls: display sound mixer controls.

Alternate graphical pointer: use “arrow” instead of “crosshairs” as the mouse’s

graphical pointer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alternate PTT Logic: activate slightly different program logic for controlling your T/R

switching via the COM port. (A few combinations of hardware and operating system

drivers seem to work better with this option checked.)

Tx Mute: mute the transmitter. Use with Auto ON to monitor one side of a QSO.

Enter new “To radio” callsign: clear the To radio and Grid boxes in preparation for

new entries.

Tx Stop forces Auto OFF: if this item is checked, clicking TX Stop during a

transmission will toggle Auto to OFF.

Mode

Select desired operating mode from this menu.

Save

Save Decoded: save any files producing decoded text in subdirectory RxWav under

your WSJT home directory.

Save All: save all recorded files in subdirectory RxWav of your WSJT home directory.

Band

Select your operating band from displayed list. The selected frequency is used for

computing EME Doppler shifts and sky background temperatures.

Help

Help: displays a brief message urging you to download and read the WSJT 4.6 User’s

Guide (the manual you are reading now).

About WSJT: displays version and copyright information.

Which message should I send? Choosing this item (or using shortcut F5) will pop up a

text box with reminders about the standard message sequences used for minimal QSOs

with FSK441, JT6M, and JT65.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alphabetical List of On-Screen Controls

Note: some controls are visible only in certain operating modes.

Add: causes the displayed callsign and grid locator to be added to the database file

CALLSIGN.TXT. If an entry for this callsign already exists, you will be asked if you want to

replace it.

AFC: activate automatic frequency control in JT65 decoding algorithm.

Auto: toggles ON or OFF timed sequencing of transmit and receive periods.

Big Spectrum: display large waterfall spectrogram for most recently decoded file. Time

increases from top to bottom, frequency from left to right. This display can help you to

identify different types of signals and noise, distinguish wanted signals from birdies, etc.

Brightness: adjust brightness of waterfall spectrogram (FSK441 and JT6M only; slider

below large graphics area). Click Decode to see effect of change.

Clear Avg: erase text in average message box, and clear message accumulator.

Clip: normally set to zero. Increase its value to 1, 2, or 3 to apply soft, moderate, or hard

clipping to a signal before attempting to decode its message. May be useful to reduce the

effects of static crashes, etc.

Contrast: adjust contrast of waterfall spectrogram (FSK441 and JT6M only; slider below

large graphics area). Click Decode to see the effect of a change.

Custom/Standard Texts: toggles between two sets of TX messages. Custom texts can be

used to store messages such as grid locator or contest information.

Decode: analyze most recently recorded or opened file, perhaps after one or more decoding

parameters (such as Freeze, Tol, Zap, AFC, or Clip) have been changed.

Defaults: reset parameters W, S, Sh, Sync, Clip, Tol, and QRN to default values.

Dsec: adjust UTC clock reading in ±1 s increments to manually resynchronize with UTC or

with your QSO partner’s computer. (In general, it is best to keep the Windows clock set

accurately and Dsec set to zero.)

EME Calc: activate the EME signal-level calculator.

Erase: clear all information in main text box and graphical areas.

Exclude: remove most recent recording from the average message accumulator. Use this

option when you are sure that the program has synchronized incorrectly (for example,

because DF and/or DT differ substantially from expected values) and you wish to avoid

contaminating the average message with bad data.

Freeze: search only frequencies within ±Tol Hz of target DF set by clicking on red spike.

Gen Std Msgs: generate standard messages; also reset TX message to 1 and Tol to 400 Hz.

Include: if signal level is greater than –32 dB, add most recent recording to average

message accumulator even if Sync is less than stated threshold.

Lookup: search database file CALLSIGN.TXTfor entry in To radio. If callsign is found, the

station's grid locator is retrieved and used to calculate distance, azimuth, elevation, and

Doppler shift.

Download from Www.Somanuals.com. All Manuals Search And Download.

Measure: initiate a series of noise power measurements.

Monitor: start a series of recordings, perhaps to monitor a calling frequency or to copy two

other stations engaged in a QSO.

Play: play most recently decoded file through sound card speaker output. This button

functions much like the “Play” button on a cassette recorder.

QRN: adjust to higher values (default=5) to suppress false decodings caused by

atmospheric noise.

Record: start recording audio noise from radio. The program will record for the time

entered in T/R Period, or until you press Stop. If Auto is ON, recording will stop when the

present T/R interval is finished; the data will then be plotted and decoded. This control

works much like the “Record” button on a cassette recorder.

S: set minimum increase in signal that will be accepted as a ping.

Save Last: save most recently recorded file. (See also Save Decoded and Save all, on the

Save menu).

Sh: set minimum strength in dB of an acceptable FSK441 shorthand message.

Sh Msg: enable transmission of FSK441 shorthand messages R26, R27, RRR, and 73.

Stop: terminate a Record, Monitor, or Play operation. This control functions much like

the “Stop” button on a cassette recorder.

Sync: set synchronizing threshold (default=1) for the JT65 decoder.

Tol: set decoder tolerance (in Hz) to frequency offsets. When DF has been established and

reduced to a small value by retuning the receiver, decrease the value of Tol to reduce the

probability of false decodings.

Tune A, B, C, D: generate steady tones at one of the four standard FSK441 frequencies

882, 1323, 1764, or 2205 Hz.

Tx 1–6: transmit selected message. Transmission will continue until the end of the present

TX sequence or, if Auto is OFF, for the duration listed in the T/R Period box.

TX First: check this box if you want to transmit during the first period of the timed T/R

cycle. Uncheck it if your QSO partner is transmitting in the first period. In this context,

“first” is defined as transmitting during the first T/R interval of an hour.

TX Stop: terminate a transmission in progress.

W: set the minimum width of pings considered for automatic decoding.

Zap: filter out birdies (narrowband signals of approximately constant amplitude) before

attempting to decode.

Main Screen Text Boxes

Average Text: displays average messages in JT65 mode.

Decoded Text: displays decoded messages and other signal information.

Dither (Hz): sets maximum random offset applied to transmitted tones in Echo mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Grid: after a successful Lookup, displays the six-digit grid locator of the callsign in the To

radio box. You can also enter a grid locator manually. If only four digits of the locator are

known, add a space.

Report: enter the signal report you wish to send to the other station, then click Gen Std

Msgs.

RIT (Hz): your receiver RIT setting in Hz.

Status Bar: panels at the bottom of the WSJT screen for displaying information such as file

name, file position, RX audio level, and decoding parameters.

Sun/Moon Data: current coordinates of sun and moon and EME path information. Click

anywhere in this box to display lunar coordinates for the DX station and MaxNR, the

maximum non-reciprocity of the EME path (caused by spatial polarization and Faraday

rotation). Click again to toggle back to the normal display.

Tavg (min): sets averaging time in EME Echo mode.

To radio: callsign of station being called. Text entered in this box becomes leading part of

recorded file names.

Appendix A: Supported Country Prefixes

If you are operating under the licensing authority of another nation, you can substitute the

portable country prefix (preceded by “/”) for your grid locator in the standard JT65 type 1

message. The supported three-character country prefixes are listed below:

1A 1S 3A 3B6 3B8 3B9 3C 3C0 3D2 3DA 3V 3W 3X 3Y 4J

4L 4S 4U1 4W 4X 5A 5B 5H 5N 5R 5T 5U 5V 5W 5X

5Z 6W 6Y 7O 7P 7Q 7X 8P 8Q 8R 9A 9G 9H 9J 9K

9L 9M2 9M6 9N 9Q 9U 9V 9X 9Y A2 A3 A4 A5 A6 A7

A9 AP BS7 BV BV9 BY C2 C3 C5 C6 C9 CE CE0 CE9 CM

CN CP CT CT3 CU CX CY0 CY9 D2 D4 D6 DL DU E3 E4

EA EA6 EA8 EA9 EI EK EL EP ER ES ET EU EX EY EZ

F FG FH FJ FK FM FO FP FR FT5 FW FY H4 H40 HA

HB HB0 HC HC8 HH HI HK HK0 HL HM HP HR HS HV HZ

I IG9 IS IT9 J2 J3 J5 J6 J7 J8 JA JD JT JW JX

JY K KG4 KH0 KH1 KH2 KH3 KH4 KH5 KH6 KH7 KH8 KH9 KL KP1

KP2 KP4 KP5 LA LU LX LY LZ M MD MI MJ MM MU MW

OA OD OE OH OH0 OJ0 OK OM ON OX OY OZ P2 P4 PA

PJ2 PJ7 PY PY0 PZ R1F R1M S0 S2 S5 S7 S9 SM SP ST

SU SV SV5 SV9 T2 T30 T31 T32 T33 T5 T7 T8 T9 TA TA1

TF TG TI TI9 TJ TK TL TN TR TT TU TY TZ UA UA2

UA9 UK UN UR V2 V3 V4 V5 V6 V7 V8 VE VK VK0 VK9

VP2 VP5 VP6 VP8 VP9 VQ9 VR VU VU4 VU7 XE XF4 XT XU XW

XX9 XZ YA YB YI YJ YK YL YN YO YS YU YV YV0 Z2

Z3 ZA ZB ZC4 ZD7 ZD8 ZD9 ZF ZK1 ZK2 ZK3 ZL ZL7 ZL8 ZL9

ZP ZS ZS8

Download from Www.Somanuals.com. All Manuals Search And Download.