Model No. 29633.1
Serial No.
TREADMILL EXERCISER
User’s Manual
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction.
If you have questions, or if there
are missing or damaged parts,
please contact the establish-
ment where you purchased
your equipment.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 17 if the treadmill is
not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
OPERATION AND ADJUSTMENT).
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails or the upper body arms while using
the treadmill.
7. The treadmill should be used only by persons
weighing 250 pounds or less.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. The pulse sensor is not a medical device.
Various factors, including the user’s move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only as
an exercise aid in determining heart rate
trends in general.
19. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
10. When connecting the power cord (see page 10),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 15.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 10.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. Inspect and properly tighten all parts of the
treadmill regularly.
23. Never insert any object into any opening.
24.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
25. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If a decal is missing, or if
it is not legible, please contact the establishment where you purchased your equip-
ment and order a free replacement decal. Apply the decal in the location shown.
Note: The decals are not shown at actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the PROFORM® CROSSWALK
400e treadmill. The CROSSWALK 400e treadmill com-
bines advanced technology with innovative design to
help you achieve your fitness goals in the convenience
and privacy of your home. And when you’re not exer-
cising, the CROSSWALK 400e treadmill can be folded
up, requiring less than half the floor space of other
treadmills.
ing this manual, please contact the establishment
where you purchased your equipment; be prepared to
provide the product model number and serial number.
The model number of the treadmill is 29633.1. The ser-
ial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the lo-
cation).
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Bookrack
Accessory Tray
Upper Body Arm
Console
Key/Clip
Handrail
Storage Latch
Upright
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Cushioned Walking Platform
for maximum exercise comfort
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wrenches
rubber mallet , and adjustable wrench
and your own phillips screwdriver
.
,
For help identifying the assembly hardware, see the drawings below. If a part is not in the parts bag, first
check to see if it has been pre-assembled. To avoid damaging plastic parts, do not use power tools for as-
sembly.
Handrail Star
Washer (95)–4
Nut (13)–2
Extension Leg
Nut (46)–4
Washer (38)–4
Star Washer
(106)–4
1/2” Screw (48)–4
3 1/2” Bolt (45)–4
3/4” Screw (2)–8
1” Tek Screw (39)–4
Silver Ground
Screw (75)–1
Extension Leg Bolt (93)–4
Wheel Bolt (64)–2
Handrail Bolt (37)–4
1. Make sure that the power cord is unplugged.
1
With the help of a second person, carefully tip the
treadmill onto its left side as shown. Partially fold the
Frame (86) so the treadmill is more stable. Do not fully
57
69
fold the treadmill until it is completely assembled.
93
Insert an Extension Leg (63) into the base of the
Uprights (69) with the Extension Leg Pad (61) oriented
as shown. If necessary, use a rubber mallet to fully insert
the Extension Leg. Next, hold two Extension Leg Nuts
(46) in the bottom of the Extension Leg, and insert two
Extension Leg Bolts (93) into the top of the Extension
Leg. Firmly tighten the Extension Leg Bolts into the
Extension Leg Nuts.
39
39
63
46
61
86
Attach two Base Pads (57) to the base of the Uprights
(69) with two 1” Tek Screws (39).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach a Wheel (66) to the base of the Uprights (69) with
a Wheel Bolt (64) and a Nut (13) as shown. Do not
overtighten the Bolt; the Wheel should turn freely.
2
64
66
69
With the help of a second person, carefully tip the tread-
mill onto its other side. See assembly step 1, and attach
the other Extension Leg (63) and the remaining two
Base Pads (57). Then, attach the other Wheel (66) as
described above.
13
With the help of a second person, carefully lower the
base of the Uprights (69) to the floor so the Uprights are
in a vertical position.
3. If there is a board between the Uprights (69), remove the
board and the two bolts. Discard the board and the bolts.
3
71
37
95
Identify the Right Handrail (72), which has a large hole in
the left side. Remove the wire tie securing the Upright
Wire (42) inside of the right Upright (69). Feed the
Upright Wire into the hole in the bottom of the Right
Handrail and out of the large hole in the side. Note: It
may be helpful to use needlenose pliers to pull the Wire
Harness out of the hole.
95
Hole
37
42
69
95
Set the Right Handrail (72) on the right Upright (69).
Attach the Right Handrail with two Handrail Bolts (37)
and two Handrail Star Washers (95). Be careful not to
pinch the Upright Wire (42).
72
69
Attach the Left Handrail (71) as described above. Note:
There is not an upright wire on the left side.
4. Hold the Console Base (47) near the Left Handrail (71).
Attach the end of the ground wire on the Console Base
to the indicated small hole in the Left Handrail with the
Silver Ground Screw (75).
4
Ground
Wire
47
Small
Hole
75
71
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Touch the Right Handrail (72) to discharge any static.
Slide the sleeve off the connector on the Upright Wire
(42) as shown in the inset drawing. Next, press the end of
the Upright Wire into the socket in the bottom of the
Console Base (47). The connector should slide easily
into the socket and snap into place. If the connector
does not slide easily and snap into place, turn the connec-
tor and then insert it. Then, slide the sleeve back over the
connector.
5
72
42
47
Connector
Sleeve
42
6. Set the Console Base (47) on the Handrails ( 71, 72).
Attach the Console Base with four 3/4” Screws (2). Start
all four Screws before tightening them; do not over-
tighten the Screws.
6
72
47
71
See the lower drawing. Make sure that the Upright
Wire (42) is routed below the two indicated round
posts (A). Next, press the Upright Wire into the slot be-
tween the square post (B) and the Console Base (47).
2
2
A
B
42
47
7. Cover the Upright Wire (42) with the Right Grip Plate
(36). Be careful not to pinch the Upright Wire. Tighten
a 3/4” Screw (2) and two 1/2” Screws (48) into the Right
Grip Plate and the Console Base (47).
7
47
Ground
Wire
Attach the Left Grip Plate (32) over the ground wire and
the other wires with a 3/4” Screw (2) and two 1/2” Screws
(48). Be careful not to pinch any of the wires.
42
36
32
2
2
48
48
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Attach the Left Upper Body Arm (24) to the left Upright
(69) with two 3 1/2” Bolts (45), two Washers (38), and
two Star Washers (106) as shown. Make sure that the
Left Upper Body Arm is on the indicated side of the
Console Base (47).
8
Attach the Right Upper Body Arm (not shown) to the right
Upright (not shown) in the same way.
47
24
69
106
38
106
45
9. Attach the Latch Housing (29) to the left Upright (69) with
two 3/4” Screws (2). Make sure that the large hole in
the Latch Housing is on the side shown.
9
Remove the knob from the pin. Make sure that the col-
lar and the spring are on the pin as shown. Then, in-
sert the pin into the Latch Housing (29), and tighten the
knob back onto the pin.
29
Knob
Large
Hole
2
69
Spring
Collar
Pin
10. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place; the large allen wrench is used to adjust the
walking belt (see page 17). To protect the floor or carpet, place a mat under the treadmill.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Pulse
Sensor
Key
Clip
FEATURES OF THE CONSOLE
HOW TO TURN ON THE POWER
The treadmill console offers a selection of features
designed to make your workouts more effective.
During each workout, you can change the speed and
incline of the treadmill with the touch of a button. As
you exercise, the console will display continuous exer-
cise feedback. You can even measure your heart rate
using the built-in pulse sensor.
Plug in the power cord (see
page 10). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
“reset” position.
Reset
MyCalories™ Personal Calorie Programming
Next, stand on the foot rails of the treadmill. Locate the
clip attached to the key (see the drawing above), and
slide the clip securely onto the waistband of your
clothes. Then, insert the key into the console. After a
moment, the displays will light. Important: In an emer-
gency situation, the key can be pulled from the
console, causing the walking belt to slow to a stop.
Test the clip by carefully taking a few steps back-
ward; if the key is not pulled from the console, ad-
just the position of the clip.
The center display of the console will show the approxi-
mate number of calories you have burned. If desired,
you can program a calorie goal before each workout,
and the console will count down the calories until you
reach your goal.
Note: If there is a sheet of clear plastic on the con-
sole, peel off the plastic. To prevent damage to the
walking platform, always wear clean shoes while
using the treadmill. The first time you use the tread-
mill, periodically inspect the alignment of the walk-
ing belt, and center the walking belt if necessary
(see page 18).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE OPERATION
Change the incline of the treadmill as desired.
4
5
To change the incline of the treadmill, press the
Incline increase or decrease button until the de-
sired incline level is reached.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
11.
Follow your progress with the three displays.
Program a calorie goal if desired.
2
The left display—This
display will show the
elapsed time and the
distance that you have
walked or run during
your workout. The dis-
play will change from one number to the other
every few seconds.
To program a calorie
goal for your workout,
press the increase but-
ton below the center
display. A goal of 100
calories will appear in
the center display. To
increase or decrease
Note: The console can display distance and
speed in either miles or kilometers, as shown by
the letters MPH or Km/H in the right display. To
change the unit of measurement, see THE IN-
FORMATION MODE/DEMO MODE on page 13.
For simplicity, all instructions in this section
refer to miles.
the goal in increments
of 50 calories, press the increase or decrease but-
ton repeatedly.
Start the walking belt.
3
To start the walking belt, press the Start button,
the Speed increase button, or one of the ten num-
bered buttons.
The center display—
The center display will
show the approximate
number of calories you
have burned during
your workout.
If the Start button or
the Speed increase
button is pressed, the
walking belt will begin
to move at 1 mph. As
you exercise, change
Note: If you have programmed a calorie goal, the
center display will show the number of calories
still to be burned. When you reach your goal, a
series of tones will sound, the walking belt will
slow to a stop, and the time will begin to flash in
the left display. If you want to continue exercising,
go to step 3 on this page.
the speed of the walking belt as desired by press-
ing the Speed increase and decrease buttons.
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. Note: After a button is pressed, it may take a
moment for the walking belt to reach the selected
speed setting.
When you use the
treadmill’s upper body
arms, press the INTER-
ACTIVE CROSSWALK
CALORIES button so
the indicator on the
If one of the ten numbered buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting.
right side of the button is lit. The console will then
include your upper body exercise as it counts the
approximate number of calories you have burned.
To stop the walking belt, press the Stop button.
The time will begin to flash in the left display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the ten num-
bered buttons.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The right display—
The right display will
show the speed of the
walking belt. The right
cure place. Note: If the displays remain lit after
the key is removed, the console is in the
“demo” mode. See THE INFORMATION
MODE/DEMO MODE on this page and turn off
the demo mode.
display will also show
your heart rate when
you use the pulse sensor (see step 6 below).
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
THE INFORMATION MODE/DEMO MODE
Measure your heart rate if desired.
6
The console features an information mode that keeps
track of treadmill usage information and allows you to
select a unit of measurement for the console.
To measure
your heart rate,
stand on the
foot rails and
place your left
thumb on the
pulse sensor.
Do not press
too hard, or
the circulation in your thumb will be restricted
and your pulse will not be detected. When your
pulse is detected, a heart-shaped indicator in the
right display will flash each time your heart beats,
one or two dashes will appear, and then your
heart rate will be shown. For the most accurate
heart rate reading, hold your thumb on the
pulse sensor for at least 15 seconds.
Pulse Sensor
To select the information mode, insert the key into the
console while holding down the Stop button, and then
release the Stop button. When the information mode is
selected, the following information will be shown:
The left display will show the
total number of hours that
the treadmill has been used
and the total number of miles
(or kilometers) that the walk-
ing belt has moved.
An “E” (for English) or an “M”
(for metric) will appear in the
right display. Press the
Speed increase button to
change the unit of measure-
ment, if desired. IMPOR-
TANT: If a “d” appears in the right display, the console
is in the “demo” mode. This mode is intended to be
used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays will remain lit; the buttons will
not operate. If a “d” appears when the information
mode is selected, press the Speed decrease button
so the “d” disappears.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb off the pulse sensor for a few seconds.
Then, reposition your thumb on the pulse sensor.
Remember to stand still while measuring your
heart rate.
When you are finished exercising, remove the
key.
7
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion, or the treadmill will become damaged. Next,
remove the key from the console and put it in a se-
To exit the information mode, remove the key from the
console.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE UPPER BODY ARMS
As you walk on the treadmill, you can hold the
handrails or use the upper body arms. To exercise
your arms, shoulders, and back for a total body work-
out, move the upper body arms forward and back as
you walk on the treadmill.
Upper Body
Arms
To vary the intensity of your upper body exercise, the
resistance of the upper body arms can be adjusted. To
increase the resistance, turn the resistance knobs
clockwise; to decrease the resistance, turn the knobs
counterclockwise.
Resistance
Knobs
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be-
come permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20 kg)
to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the frame by the plastic foot rails.
Bend your legs and keep your back straight; as you raise
the frame, make sure to lift with your legs rather than
your back. Raise the frame about halfway to the vertical po-
sition.
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the frame until the hole in the frame
is aligned with the latch pin. Slowly release the latch knob;
make sure that the latch pin is fully inserted into the
frame.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sun-
light. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Engaged
Latch
Knob
Frame
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch pin is
fully inserted into the frame.
1. Hold the upper ends of the handrails, and place one foot
against one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while mov-
ing the treadmill. Do not move the treadmill over an un-
even surface.
Wheel
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill with your right hand as shown. Pull the
latch knob to the left and hold it. Pivot the frame down until it
is past the latch pin.
Latch
Knob
Frame
2. Hold the metal frame firmly with both hands, and lower the
frame to the floor. CAUTION: To decrease the possibility of
injury, do not lower the frame by gripping only the plastic
foot rails. Do not drop the frame to the floor. Make sure to
bend your legs and keep your back straight.
Frame
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 10. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
Tripped
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
POWER CORD. Remove the Screws (115) from the
Hood (1), and carefully pivot the Hood off.
115
1
Locate the Reed Switch (10) and the Magnet (18) on
the left side of the Pulley (17). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(114), move the Reed Switch slightly, and then
retighten the Screw. Reattach the Hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
1/8”
114
17
18
10
Top
View
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 10.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller bolts counterclockwise, 1/4 of a turn. When
the walking belt is properly tightened, you should be
able to lift each edge of the walking belt 2 to 3 inches
off the walking platform. Be careful to keep the walk-
ing belt centered. Then, plug in the power cord, insert
the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
2”–3”
Rear Roller Bolts
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the allen wrench to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the bolt
counterclockwise 1/2 of a turn. Be careful not to over-
tighten the walking belt. Then, plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
a
b. If the walking belt slips when walked on, remove the
key and UNPLUG THE POWER CORD. Using the
allen wrench, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 2 to 3 inches off the walking platform. Be careful
to keep the walking belt centered. Then, plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
b
PROBLEM: The upper body arms squeak during use
SOLUTION: a. (Note: Correcting this problem requires a small amount
of white marine grease, available at hardware stores.)
Turn the Resistance Knob (109) counterclockwise and
remove it. Next, remove the Resistance Cone (108)
and the Upper Body Arm (24), along with the
a
105
107
24
Resistance Plate (27), Washers (5), Spring Washer
(111), Thrust Washers (112), and Thrust Bearing
(113). (Note: If the Resistance Sleeve [107] or the
Resistance Plate [27] comes out of the Resistance
Bracket [105] or the Resistance Cone [108], press it
back in.) Apply a thin layer of white marine grease to
the outer surface of the Resistance Cone (107). Then,
reattach all parts in the order shown at the right.
112
111
109
108
27
113
5
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including the user’s move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only as
an exercise aid in determining heart rate trends
in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning, and the higher number is
the recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-
exercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 29633.1
R0506A
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
1
9
1
2
4
1
1
1
2
1
1
2
9
2
2
2
1
1
1
2
2
Hood
3/4” Screw
Motor Belt
Motor Tension Bolt
3/8” Washer
Motor Star Washer
Flywheel
Drive Motor
Foot Rail Cover
Reed Switch
Latch Warning Decal
Frame Spacer
Nut
Frame Pivot Bolt
Platform Screw, Front
Handrail Cap
Front Roller/Pulley
Magnet
Motor Pivot Bolt
Motor Bracket Bolt
Upper Body Arm
Endcap
43
44
45
46
47
48
49
50
51
52
53
1
2
4
4
1
6
1
1
1
2
1
Console
Rear Roller Plate
3 1/2” Bolt
Extension Leg Nut
Console Base
1/2” Screw
88
1
Console Warning
Decal
Cable Tie Clamp
Front Roller
Star Washer
89
90
2
1
91
92
93
94
95
96
97
98
99
1
1
4
1
4
1
1
1
4
1
2
Reed Clip
Wire Clamp
Key/Clip
Ground Screw
Extension Leg Bolt
Allen Wrench
Handrail Star Washer
Walking Belt
Walking Platform
Right Foot Rail
U-nut
Rear Roller
Upper Body
Arm Screw
Incline Motor
Incline Motor
Rear Roller Washer
Incline Motor
Bolt, Lower
Incline Pivot Bolt
Incline Pivot Nut
Motor Controller Wire
Round Base Pad
3/4” Tek Screw
Controller
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
2
2
1
4
10
1
1
2
2
2
2
2
2
2
4
1
1
1
1
6
1
1
2
4
1
1
2
1
2
4
4
2
1
4
100
101
102
3
Lift Frame
Bolt, Upper
Extension Leg Pad
Warning Decal
Extension Leg
Wheel Bolt
Base Endcap
Wheel
1/4” Nut
8” Cable Tie
Upright Base
Grommet
Left Handrail
Right Handrail
Rear Endcap Screw
Left Foot Rail
Silver Ground Screw
Foam Grip
Belly Pan Screw
Right Rear Endcap
Power Cord Assembly
Rear Roller Bracket
Belly Pan
103
104
105
106
107
108
109
110
111
112
113
114
115
116
1
2
2
4
2
2
2
1
2
4
2
1
3
2
Motor Mount Bracket
Resistance Bolt
Resistance Bracket
Star Washer
22
23
24
3
3
1
Hood Clip
Roller Adj. Bolt
Left Upper Body Arm
w/Grip
Right Upper Body
Arm w/Grip
Ground Screw
Resistance Plate
Motor Tension Nut
Latch Housing
Latch Catch
Left Rear Endcap
Platform Screw, Rear
Static Decal
Left Grip Plate
Roller Bracket Screw
Right Grip Plate
Handrail Bolt
Washer
1” Tek Screw
Ground Wire
Rear Roller
Resistance Sleeve
Resistance Cone
Resistance Knob
Latch Pin Assembly
Spring Washer
Thrust Washer
Thrust Bearing
Reed Clip Screw
Belly Pan Screw
Platform Washer
Foot Rail Screw
4” Black Wire, M/F
8” Green Wire, F/R
4” Blue Wire, 2F
4 ” Red Wire, M/F
User’s Manual
25
1
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
4
2
2
1
1
2
2
2
1
2
1
4
6
4
1
2
117 10
#
#
#
#
#
1
1
2
1
1
Belt Guide
#These parts are not illustrated
Belt Guide Screw
Isolator Fastener
Isolator Cushion
Frame
Star Washer
Upright Wire
42
1
Releasable Tie
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS EXPLODED DRAWING AND PART
LIST FROM THE MANUAL
Save this EXPLODED DRAWING and PART LIST for future reference.
4
3
Note: Specifications are subject to change without notice. For information about
ordering replacement parts, see the back cover of the User’s Manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. 29633.1
R0506A
3
28
22
7
76
22
22
8
1
24
4
4
10
114
91
27
112
12
117
111
5
109
104
9
60
117
105
113
19
107
23
101
90
13
13
106
13
18
17
14
117
108
21
117
15
117
12
82
9
84
85
74
117
15
83
117
14
30
117
63
58
96
117
98
11
65
82
32
116
35
67
80
117
97
84
83
58
115
26
85
44
41
84
58
32
116
52
100
44
35
23
26
31
49
86
52
41
23
87
67
80
68
58
89
92
40
73
73
81
73
94
Download from Www.Somanuals.com. All Manuals Search And Download.
47
43
6
34
20
28
99
103
48
20
75
56
13
42
2
2
88
99
110
2
29
2
2
2
102
37
95
36
37
48
95
37
2
95
38
45
51
66
76
13
13
64
53
72
71
16
45
38
54
55
16
93
50
55
42
57
39
54
62
93
39
46
57
70
25
69
61
58
13
79
57
62
64
66
109
39
63
65
39
101
107
26
115
113
46
5
58
108
33
111
61
58
112
21
27
115
26
105
106
59
104
58
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, please contact the establishment where you purchased your equipment. When call-
ing, please be prepared to provide the following information:
• the MODEL NUMBER of the product (29633.1)
• the NAME of the product (PROFORM CROSSWALK 400 e treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and the PART
LIST attached in the center of this manual)
Part No. 242498 R0506A
Printed in USA © 2006 ICON IP, Inc
Download from Www.Somanuals.com. All Manuals Search And Download.
|