Installation Instructions
XL6000CM
Projector Mount
AUSTRALIA, NEW ZEALAND,
OCEANIA (DISTRIBUTOR)
P.O. Box 295
EUROPE
Swallow House,
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada -
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Mordialloc Victoria 3195
Australia
Phone: 03 9586 6330
Phone: 800-368-9700
Fax: 800-832-4888
9530-019-461-01
Download from Www.Somanuals.com. All Manuals Search And Download.
XL6000CM
Congratulations on the purchase of your new Premier Mounts PDS Projector Mount.
Parts List
This mount is shipped with all installation hardware and components. Make sure that none of these
parts are missing and/ or damaged before beginning installation. If there are parts missing and/
or damaged, please stop and contact Premier Mounts at (800) 368-9700.
Please review all WARNING and CAUTION statements (Page 8) before beginning the installation
of the PDS Series Projector Mount.
M6 x 12mm Phillips
Pan Head w/
Integrated Split
Washer (Qty 12) - 6
come preinstalled on
the PDS
PDS Mount (Qty 1)
Nylon Spacer (Qty 2)
#14 x 2” Wood
Screws (Qty 2)
Flat Washer
(Qty 2)
LOCK-IT™ Security System
M6 x 8mm
Socket Head Set
Screw (Qty 1)
M6 x 12mm Security
Screw (Qty 12) -
Included in the LOCK-
IT™ packet
Escutcheon Ring
(Qty 1)
External Tooth
Lock Washers
(Qty 4)
M6 x 8mm Security Set
Screw (Qty 1)
Installation Tools
Phillips Head Screw Driver
Soft Material/ Blanket
Level
Portable Drill
Pencil
Stud Finder
M3 Security Allen Wrench (Supplied)
M5 Security Allen Wrench (Supplied)
Installation Instructions
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
XL6000CM
Ceiling Installation
Upper Bridge
Ceiling Wood Stud
Ceiling
Surface
Base Box
Mounting Slot
Figure 1
Upper Bridge
1. Separate the Upper Bridge from the Base Box
by removing the six (6) M6 x 12mm Phillips Head
screws three on each side (Figure 1).
#14 x 2” Wood Screws
Figure 2
2. Use the appropriate slot openings for single wood
stud mounting, depending on your ceiling
Ceiling Wood Stud
configuration. The adjustable channel slots will
allow you to fine tune the final orientation of the
projector.
3. Secure the Upper Bridge to the center of the stud on
the ceiling structure at this time using two (2)
#14 x 2” wood screws (supplied).
Ceiling
Surface
M6 X 12mm
Phillips Head
Screw
Base Box
Figure 3
4. Attach the Base Box to the Upper Bridge and
secure with the six (6) M6 x 12mm Phillips
Head screws (Figure 3). DO NOT TIGHTEN
THESE SCREWS YET.
Page 4
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
XL6000CM
Attaching the Projector
NOTE:
Please follow the installation sheet included
with the specific mounting bracket for your
projector. Once the mounting bracket has
been secured to the projector, follow the
instructions below.
Set Screw (NOTE:
Use set screw only
when attaching to
pipe).
1. Raise the projector (with the mounting bracket
attached) and hook the projector bracket over the
hinge screws (Figure 4).
CAUTION: Make sure the bracket is fully secured to
the Base Box before letting go of the
projector.
M6 x 12mm Phillips
Head Screws (Attach after
the bracket has been
Hinge Screw Hole
mounted and tightened)
2. Loosely install the two (2) M6 x 12mm Phillips Head
Hinge screws, flat washers and nylon spacers into
the hinge holes, located on each side of the base
box (Figure 4). DO NOT TIGHTEN THESE
SCREWS!
3. Once the mount is safely attached, insert and
tighten the four (4) M6 x 12mm Phillips Head
Screw (Figure 4).
Nylon Spacer
4. Once all adjustments have been made, tighten all
hardware.
Flat Washer
Projector
Bracket
M6 x 12mm
Phillips Head
Hinge Screw
Figure 4
Adjusting the Projector
1. You can adjust the roll of the projector by loosening the
three (3) front and rear M6 x 12mm screws (Figure 5).
Do not fully loosen the screws, as the
mount may drop.
Roll
2. Set the desired roll and then tighten the screws. First
tighten the center screws and work your way to the
outside screws, making any final adjustments prior to
tightening the last two screws.
3. You can adjust the tilt of the projector by loosening the
two (2) M6 x 12mm screws on each side of the Base Box
(Figure 5).
4. Set the desired tilt and then tighten the screws, making
any final adjustments prior to tightening the last two
screws.
Tilt
If your projector is not holding the tilt, install the
four (4) internal/external tooth lock washers to the
four (4) M6 x 12mm tilt screws.
5. Once all adjustments have been made, tighten all
hardware.
Installation Instructions
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
PDS-Series
Optional Installations
AST-2446 Installation/ Custom Length Pipe
(1-1/2” NPT)
NOTE: These installation instructions apply only to installing the
PDS Base Box. For complete AST-2446 Custom Length Pipe
(1½” NPT) installation instructions, please refer to the
AST-2446 Custom Length Pipe (1½” NPT) Installation
Instructions.
Custom Length
of NPT Pipe
1. After the upper pipe has been properly secured to the ceiling
structure, screw the base box to the lower portion of the
AST-2446 and secure it with the M6 x 8mm set screw (Figure 6).
2. Make the necessary viewing adjustments (please see Page 5,
Adjusting the Projector).
3. To install the escutcheon ring, open the ring, place it around the
AST-2446 extension pipe, and close. The escutcheon ring must
then be fitted into place.
4. When all final adjustments have been made, tighten all hardware.
AST-2446, or Custom Length
of Pipe
PDS Base
Box
Set Screw (tighten once the
desired position is locked in).
Projector
Bracket
Projector
Figure 6
PP-FCTA Installation
NOTE: These installation instructions apply only to
installing the PDS Base Box. For complete
PP-FCTA installation instructions, please refer to
the PP-FCTA Installation Instructions.
PP-FCTA
Escutcheon Ring
Ceiling
Tile
1. Secure the 1½" (NPT) nipple to the ceiling plate and
secure the nipple or (custom length of 1½” NPT pipe)
by using one (1) M5 x 16 Phillips head screw
(supplied) to the stud plate (Figure 7).
1-1/2” (NPT) Nipple,
or Pipe
XL6000CM
Frame
Ceiling
2. Thread the base box to the pipe, or nipple, and secure
with the M6 x 8mm set screw.
3. To install the escutcheon ring, open the ring, place it
around the pipe, and close. The escutcheon ring must
then be fitted into place.
Set Screw (tighten once
the desired position is
locked in).
Projector
Bracket
4. When all final adjustments have been made, tighten all
hardware.
Figure 7
CAUTION:
The set screw must be used to stabilize
the 1½" (NPT) nipple or optional pipe.
Page 6
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
PDS-Series
Technical Specifications
All measurements in inches (mm)
Installation Instructions
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
XL6000CM
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime
of the original owner of this product. The limited warranty is valid only for the original purchaser of the
product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that
is defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part
will be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS,
DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE
OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS
PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER
MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR
REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing
to the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original
consumer purchaser must accompany all warranty claims. Warranty claims must also include a description
of the problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to
Premier Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone
or by fax.
Premier Mounts
Attn: Warranty Claim
3130 E. Miraloma Avenue
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
Page 8
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
XL6000CM
M4 x 10mm
Knurl Knobs
XL6000CM Projector Bracket Installation Instructions
XL6000CM
Mounting
Bracket
HC5000
Safety
Strap
HC5000 Safety Bracket Installation
1. Once the XL6000CM has been attached to the projector, the safety strap
must be attached to the mounting bracket.
2. Place the safety bracket over the mounting holes and insert two (2)
M4 x 10mm knurls knobs and tighten.
Safety Strap
(Qty 1)-For use
with the
PDS-046 Bracket
HC5000/6000
(Qty 1)
projector
M4 x 10mm
Knurl Knobs
Safety Strap
(Qty 1)-For use
with the
XL55OU/650
projector
M4 x 10mm Knurl
Knobs (Qty 2)
XL6000CM
Mounting
Bracket
M4 x 10mm
Security Head
Screws (Qty 3)
M4 x 10mm Phillips
Head Screw (Qty 3)
Premier Mounts
3130 E. Miraloma Ave.
Anaheim, CA 92806
XL55OU
Safety
Strap
Phone: (800) 368-9700 Fax: (800) 832-4888
M4 x 10mm Phillips
Head Screw
XL55OU Safety Bracket Installation
1. Once the XL6000CM has been attached to the projector, the safety strap
must be attached to the mounting bracket.
2. Place the safety bracket over the mounting holes and insert two (2)
M4 x 10mm knurls knobs and tighten.
XL6000CM
Mounting
Bracket
Screwdriver
M4 x 10mm Phillips
Head Screw
Mounting
Point
Mounting
Point
Mounting
Point
Projector
Projector
1. Using a screwdriver, secure the XL6000CM mounting bracket using three
(3) M4 x 10mm Phillips Head screws. Do not over tighten these screws.
Overtightening the screws may result in damaging the threaded inserts on
the projector.
1. Invert the projector and place it on a soft and flat surface. Remove any foot
levelers that might possibly prevent the correct installation of the bracket.
2. Locate the three mounting points located on the bottom of the projector.
3. Line up the mounting points on the projector with the mounting holes on
the XL6000CM mounting bracket.
Please refer to the Base Box Installation Instructions to attach
the Base Box to the XL6000CM mounting bracket.
The projector (shown above) is for illustration purposes only.
Installation Instructions
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCK-IT™ Security System
LOCK-IT™
Security System
Premier Mounts
3130 E. Miraloma Ave.
Anaheim, CA 92806
Phone: (800) 368-9700 Fax: (800) 832-4888
To utilize the LOCK-IT™ Security System, all M6 x 12mm
Phillips Pan Head screws (A) must be removed prior to
installing the M6 x 12mm Security Screws (D).
1. Remove all pre-installed M6 x 12mm Phillips Pan Head screws
(A - 6 total).
2. Use the M5 Security Wrench (B - supplied) to install and tighten the
M6 x 12mm Security Screws (D).
3. Using the security wrench (supplied), remove the M6 x 8mm standard
set screw and replace it with the M6 x 8mm security set screw (C).
4. Insert the nylon washer (G), 1/4” flat washer (H) and the M6 x 12mm
Security Screw (D) into the pivot point (I).
5. Attach bracket to projector using security screws.
6. Once the Phillips Pan Head screws have been replaced with the
security screws, re-attach the bracket (E) to the mount (F).
7. Insert the four tilt adjustment security screws (two per side).
8. Follow the instructions in the manual to complete the installation.
Mounting Bracket Security Screws
1. Using a security wrench (supplied), secure the XL6000CM mounting
bracket using three (3) M4 x 10mm Security Head screws. Do not over
tighten these screws. Overtightening the screws may result in damaging
the threaded inserts on the projector.
Allen Wrench
M4 x 10mm Security
Head Screw
Projector
Installation Instructions
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|