USER GUIDE
DT Chassis Industrial Printers/Plotters
Model 840DL/G • 820DL/G • 820G • 810
Desk Top (DT) Chassis
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1-1
This User Guide describes the general operation and care of the DT (Desk Top) Chassis
series of industrial printers/plotters. The specific DT Chassis models covered by this guide
are the 840 DL/G, 820 DL/G, 820G and 810.
Overview
These products are designed for use in a variety of environments, including rugged mobile
data logging and exploration systems. While highly durable and reliable in service, best
performance and product life will be assured if some degree of care is taken when installing
the printers and when providing routine maintenance.
Reading the following sections describing the setup, operation and basic care of the printer
will very likely answer questions you might have regarding these aspects of using Printrex
products. Should you have further questions, more information is available as described in
the Additional Documentation section of this guide. If the documentation fails to address
your concerns, please contact Printrex support (see Contact Information) and we will make
every effort to provide a solution.
Refer to the following table for the discriminating DT Chassis features.
Model
840DL/G 820DL/G
820G
2
810
1
Print Speed (ips)
4
2
ü
ü
ü
ü
ü
ü
ü
ü
-
Integrated Internal Roll
Bottom Feed Fan-fold
Film/Mylar Media Support
Win95/98/ME and Win2000/XP Support
Vertical Line Adjustment
Extended Media Controls
32 Level Gray Scale Printing
Autorange 115/220VAC Power
Fan Cooled
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
-
ü
-
ü
ü
ü
ü
ü
ü
-
ü
ü
ü
-
-
ü
-
CE Certification (ITE, Safety and EMC)
FCC Class A
ü
ü
ü
ü
ü
ü
Firmware (Software)
Information
The Firmware (Software) resident in the Printer is owned by Printrex or its suppliers and is
licensed for used only on a single printer in the user’s Trade or Business. The User agrees
not to, and not to authorize or permit any other person or party to duplicate or copy the
Firmware or the information contained in the nonvolatile or programmable memory. The
firmware (Software) is protected by applicable copyright laws and Printrex retains all rights
not expressly granted. In no event will Printrex or its suppliers be liable for any damages or
loss, including direct, incidental, economic, special, or consequential damages arising out
of the use or inability to use the Firmware (Software).
Copyright Information
Windows and Windows NT are trademarks and Microsoft is a registered trademark of
Microsoft Corporation.
Ethernet is a registered trademark of Xerox Corporation.
All other brand and product names are trademarks, service marks, registered trademarks or
registered service marks of their respective companies.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1-2
You should find the following items when unpacking your printer. If any of these items are
not found with the printer, please contact Printrex Customer Service.
Package Contents
•
•
•
DT Chassis Printer
8 3/4 Inch Paper Carrier
Paper Rod
US
(SUS suffix)
•
•
•
Power Cord (one of the three US, UK or Central Europe
plug type, according to the order number suffix)
Central Europe
(SCE suffix)
United Kingdom
(SUK suffix)
Thermal Paper Roll
This Manual
There is also a styrene spacer that keeps the print head pressure off the platen during shipment
and storage. This spacer is not required for operation and can be discarded.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1-3
Refer to the Feature Description TableFigures 1 through 4 to familiarize yourself with the
features of the printer. The names of these features will be used throughout this guide.
Getting Familiar
Feature Description Table
FEATURE
DESCRIPTION
FIGURE
Bottom Feed Slot
Chassis Label
Paper entrance slot for bottom paper feed applications
3
Indicates Part Number, Revision, Full Model and Serial Number
For opening and latching closed
2
1
4
5
1
1
4
4
5
1
1
1
2
5
2
4
2
Door Latches
Error Indicator
Indicates error conditions (see Errors and Error Handling)
Form detector window to view form mark
Operator controls and indicators
Form Sensor Window
Front Panel
Model Label
Indicates the installed print engine model
Advance paper and used to enter self-test
Indicates a paper empty condition
Paper Advance Button
Paper Empty Indicator
Paper Empty Switch
Paper Rod
Paper empty detection switch
Center spindle for internal roll paper supply
Internal roll paper holder
Paper Carrier
Paper Tear Edge
Parallel Interface Connector
Platen
Paper tearing bar
High speed parallel interface connector to host computer
Printer platen roller
Power Entry Module
Power Indicator
Power Switch
IEC power entry module for power entry
Indicates power is applied to the printer
Controls power to the printer
Figure 1
Model Label
Paper Tear
Edges
Paper Rod
Front
Panel
Door Latches
Paper Carrier
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1-4
Getting Familiar
(Continued)
Figure 2
Power
Switch
Power Entry
Module
Chassis
Label
Parallel
Interface
Connector
Figure 3
Paper
Advance
Button
PAPER
ADVANCE
Bottom Feed Slot
(840DL/G and
820DL/G only)
Figure 4
Paper
Empty
Indicator
PAPER
EMPTY
Error
Indicator
ERROR
POWER
Figure 5
(Chassis not shown)
Power
Indicator
Print Head
Assembly
Form
Sensor
Window
Paper
Empty
Switch
Platen
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup
2-1
Many different OEM organizations have been integrating Printrex products into combined
hardware and software systems; some for nearly 20 years. These complete-solution products
may be assembled in closed physical packaging or racks, or may consist of pre-configured
computer hardware that is deployed like any other office equipment. Software may be
command-line or graphically operated, and might be installed with a Unix-type or Microsoft
operating system. Interconnection interfaces include various types of parallel or serial
ports, USB and/or Ethernet.
OEM
Configurations
While Printrex has experience in supporting the development of a variety of these OEM
systems, it is impossible for us to maintain the information and knowledge necessary to
provide detailed support in the operation of these systems. Persons having questions
regarding use of a specific product are best advised to consult the documentation or support
services provided by the OEM.
For clients directly receiving Printrex products to install as end users into existing or new
systems, we wish to make the installation process as trouble-free as possible. Several
documents are available for reference which are intended to describe the most common
installation scenarios (see the Additional Documentation section of this guide).
First, be sure to use a high-quality cable. The cable should be marked “IEEE-1284” to
indicate compliance with this communications standard. Inexpensive cables are electrically
inferior and can result in unnecessary communications errors.
Connecting the
Parallel Interface
Connect the 25-pin connector end of the cable to the parallel port of the computer. Use the
screw locks to secure the cable, but do not tighten excessively.
Make sure the printer power is off, then, plug the Centronics 36-pin connector end of the
cable into the printer and engage the spring clips to lock the connector.
Avoid making any other connections between computer and printer, whether to add extension
cables or to install daisy-chain disk drives or scanners. Integrity of communications is
greatly degraded when these items are in the signal path.
For other installation and connection options, please refer to the Printrex System
Administrator’s Guide.
First turn Power Switch to the off position (the off position is shown by the international
symbol “O”). Connect the IEC female end of the cord to the power connector on the rear of
the printer chassis. Plug the male connector into a properly grounded three- pin AC main
power outlet.
Connecting the
Power Cord
Do not use a “cheater” connector in order to use an inexpensive two-wire outlet or extension
cord. This defeats the grounding protection of the product and may introduce a serious
electrocution hazard in wet environments.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup
2-2
The majority of Printrex customers use our printers with computing equipment that functions
with the support of an operating system. Microsoft Windows XP and Windows 2000 are
the most prevalent systems in current use. In order to provide the best quality of printed
output and most convenient user interface, Printrex continually reviews and updates drivers
for these platforms.
Operating System
Setup
The ‘consumer’ operating systems ( Windows 95, 98, and ME ) are in the twilight of support
by Microsoft and are therefore supported at a lower priority by Printrex as well. Specific
issues regarding current drivers for these platforms may be referred to Printrex technical
support for correction; custom feature additions will be addressed on a per request basis.
The paragraphs below apply to users installing printers by connecting directly to the computer
in use. For connecting to a network, see the following section on Network Setup.
WindowsTM 2000/XP
Because drivers for these platforms are subject to periodic updates, visit the Printrex website
compressed file onto a floppy disk and open the Printers folder ( Start – Settings – Printers).
Start the Add Printer wizard and follow the instructions, selecting Have Disk when prompted
for ‘Manufacturers’ and ‘Printers’.
After completing the wizard, right-click on the new printer icon in the Printers folder, and
select ‘Printing Preferences’. Click the Advanced... button to display the Advanced Options
dialog. This determines the “default” settings of the printer. Most users will wish to change
the Paper Size from ‘Letter’ to the actual form loaded in the printer, as well as the Media
Selection and Form Marker Type. Other settings may need adjustment as well, depending
on application.
For further information on installation, see publication 1028-0061, Printrex Driver Installation
Guide.
After installation, publication 1028-0062, Printrex Windows Driver User Guide may be
used as a reference in applying the driver settings needed for a particular printing task.
Many different types of applications can be accommodated by the drivers, using a variety
of media. While the default control values are a good starting point for most print jobs,
many users will wish to fine-tune driver settings to obtain the best quality possible.
WindowsTM 95/98/ME
First, check the Printrex website for updated driver versions ( www.printrex.com/drivers.htm).
After extracting the compressed driver files to a floppy disk, go to the Start – Settings –
Printers folder, and double-click Add Printer. Proceed with installation, and click the Have
Disk button when the ‘Manufacturer’ - ‘Model’ dialog is displayed. When the wizard
finishes, right-click on the printer icon and select ‘Properties’. Make adjustments as needed,
for paper size, media type, and other features. For further information on installation, see
publication 1028-0063, Printrex System Administrator’s Guide.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup
2-3
UNIX and Other Operating
Systems
At this time, Printrex does not distribute filter files for UNIX (and UNIX-type) platforms.
Users of applications designed for use on these systems are advised to contact the application
vendor for assistance with setup.
Many permutations of network connections and configurations exist. It is well worth taking
some time to design the installation with consideration to future expansion and updates.
Network Setup
When connecting the printer within a mixed environment, there are additional choices
available and decisions to be made. Hardware print server boxes provide multi-protocol
support for numerous platform configurations and communications standards.
Refer to publication 1028-0063, Printrex System Administrators Guide for further information.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3-1
Unlock the door of the printer by
pressing on the open circles printed on
the two latches at the lower corners of
the door. Pull up on the latches to open
the door.
1 Unlock Door
Loading Paper
Loading An Internal Roll
2 Remove Paper Holder
Remove the paper carrier from the
printer and remove the paper rod
from the carrier. Slip the empty
core off the paper rod.
3 Insert Roll In Printer
Slip the paper rod through the core of
the new paper roll and install the paper
roll on the carrier so the paper feeds
from the top of the roll toward the front
of the carrier. Feed a few inches of
paper from the roll so it will extend
over the platen after insertion.
Insert the paper carrier in the printer and
close the door with the latches unlocked.
4 Lock Door
Press on the solid circles printed on the
door latches to lock them. Tear off the
extra paper.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3-2
Loading external media is similar to loading an internal roll. The difference being the paper
is threaded through the bottom feed slot. Note:The printer is shown with an optional Paper
Tray. See Accessories Section 5-2 for ordering information.
Loading Paper
Continued
Loading External Media
(Models 840DL/G and
820DL/G only)
1 Place Printer On Stand
Printer
Place the printer on the paper tray.
The printer position is set by the feet
and side plates of the paper tray.
2 Rotate Printer to Upright Position
Rotate the printer to the
upright position, open
Paper Tray
the door and remove
the paper carrier.
3 Thread Paper
Insert paper through the Bottom Feed
Slot and out through the door as
shown. Observe the orientation of the
Forms Mark for correct top-of-form
operation.
Position 11 inch forms even w
ends of the paper guides f
correct position. CenterAPI
forms between the ends of
the paper guides for
correct position.
4 Return Printer to Operating Position
Return the printer to the
horizontal position, inser
paper carrier and close
the door.
Paper Guides
Forms Mark
Note: The paper carrier must be
installed to position the paper over
the paper empty sensor and the
form mark sensor.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3-3
There are two tear bars; one on the bottom of the front door for tearing up and one on the
printer housing for tearing down. Pull up or down at approximately a 45° angle and slightly
to the right or left to tear the paper.
Tearing Paper
45 o
The forms mark sensor is located in the front right side of the printer. Be sure the paper is
loaded as shown below for correct top of form (TOF) detection. Also, be sure the paper size
is correctly selected in the WindowsTM driver.
Forms Marks
A listing of media providers that supply paper with the
Insert into printer
specified form marker location can be found on the
0.5 In.
0.25 In.
suppliers can supply compatibly marked forms prov
they receive the marker specifications shown to
Perforation
0.5 In.
the right.
Uncoated side
of paper
Coated side
of paper
Forms mark
Perforation
Forms Mark
To perform self test, press and hold the PAPER ADVANCE button while turning on power.
The PAPER ADVANCE button may be released after self test has started. In self test, the
ERROR indicator lights and a printout of model, interface type, firmware version and other
various test patterns is started. The test printout will stop after the last test pattern is printed
and the printer will exit self test and return to normal operating mode.
Running Self Test
There are times when it is useful to have the test pattern repeated. If the PAPER ADVANCE
button is held while the first self test pattern is finishing, the printer will enter a repeating
self test mode where the entire self test pattern is repeated until the unit is powered off.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3-4
After loading paper, or any time you wish to advance paper, press the Paper Advance button
on the front panel. The printer will feed paper as long as the button is pressed, but will stop
when either of two conditions is met:
Advancing Paper
•
•
If the paper has form markers printed on the back surface, the printer will stop
when a marker is detected.
The logical page length has passed without a form marker being seen. The power-
up default page length is 16.7 inches. This length may be changed by sending the
printer control codes in software.
Releasing the button and pressing again repeats the cycle of feeding and stopping.
When print jobs are sent to the printer continuously, there is no mechanical duty cycle
limitation; some users report 10 hours a day of nonstop printing as normal usage. However,
if the print data contains an unusually high proportion of black areas, the printer may go
into an over-temperature condition. This may also occur when printing less dense print
jobs if the ambient temperature is very high. Refer to the following section on Errors and
Error Handling for information on the front-panel indication of temperature errors. Recovery
from temperature errors is automatic, and needs no user action to resume printing.
Printing
If paper has been loaded askew, or has been torn off forcefully, or is damp, the paper may
feed abnormally and wrap around the platen roller. These occurrences are extremely rare,
but it is important to know the following method of clearing the jam:
Clearing a
Paper Jam
•
•
•
•
Turn off power to the printer.
Open the printer door, and remove the paper holder and roller.
Tear off the incoming paper (either from the roll, or fanfold supply).
Pull on the free end of paper with one hand, while turning the platen roller with
the other hand, to unroll paper from the platen.
•
•
Do not use a razor, knife or sharp object of any kind to cut the paper off of the
platen roller. Nicking or cutting the roller surface will result in worsening damage
to the platen with continued use of the printer.
Be very careful not to damage the print head that is exposed on the underside of
the door. This should not be an issue if only bare hands are used to free the paper.
The Front Panel controls are intentionally minimal. This ensures that one user’s print jobs in
a network environment are not ruined by other users manually making unannounced changes
to printer settings. The Printrex Windows drivers send control codes to the printer for each
print job, so it is important to check driver settings before printing. Note that some
geotechnical applications bypass the Windows drivers, and provide a limited subset of
printer controls. Check with your application’s documentation to determine if this is the
case. If so, settings made in the Windows driver will not affect printing from these
applications.
Additional Controls
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3-5
The Error Indicator on the Front Panel indicates an error condition of the printer.This indication
is in the form of a two digit error code expressed as a series of long flashes (for the tens digit)
then short flashes (for the ones digit). The tens digit flash is twice as long as the ones digit
flash. Example: One long flash followed by two short flashes indicates an error code of 12
(Door Open).
Errors and Error
Handling
The Error Indicator will continue to flash the error code while the error condition exists.
Refer to the following table for a list of error codes and their meaning.
ERROR
CODE
NAME
DESCRIPTION
11
Paper Empty
A paper empty condition exists.
Cleared by loading paper.
12
Door Open
One or both of the Door Latches are unlatched.
Cleared by latching both door latches.
21(1)
22
Under Voltage
Over Voltage
The internal DC supply voltage is too low to print properly.
Service is generally required to clear this condition.
The internal DC supply voltage is too high to print properly.
Service is generally required to clear this condition.
23(1)
24
Under Temperature The thermal head is too cold to print properly.
Cleared when the ambient temperature sufficiently increases.
The thermal head is overheated.
Cleared when the thermal head cools off.
Over Temperature
NOTE 1: Model 810 does not indicate an Under Voltage or an Under Temperature condition. The model 810
printer will print as best as possible given the voltage or temperature is lower than nominally expected.
This section lists a few common questions that are received by Printrex support staff and the
answers most likely to fix the problem. For further information, see the Printrex System
Administrator’s Guide.
Troubleshooting
1. The printer seems to be working but nothing is printed.
The thermal paper has one side that has a thermal sensitive coating while the other side is
not coated. Be sure the thermally coated side is facing upward (as the paper is exiting the
printer).
2. My printer is too slow! What’s wrong?
(Windows XP/2000/NT4)
These operating systems do not support high speed data transfer using the default (Microsoft)
parallel port driver. Printrex recommends using a USB to Parallel converter cable when
connecting the printer directly to PCs using these operating systems.
(Windows 95/98/ME)
Check the parallel port settings in the BIOS and be sure it’s set to ECP mode.
3. I’m using fanfold paper with form markers, but the printer stops in the wrong place.
What driver settings should I use?
Be sure to set the Paper Size to the actual size of the paper (8.75 x 6.25), and enable End-of-
Job Form Feed. Also, see that the Form Marker setting (in Windows XP/2000 driver) matches
the actual printed location of the marker. Check that the paper is loaded correctly: looking
at the front of the printer, the marker should be on the right side, on the bottom of the paper.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3-6
4. I’m trying to print TIFF files, but the printed output is clipped off. How do I print the
whole log?
Troubleshooting
(Continued)
This question has come from the geotechnical community frequently over the last several
years. Commonly, users view TIFF logs in Windows Imaging, the free viewer provided in
the Programs- Accessories folder. Unfortunately, this is a single-page application: it is
designed for simple photograph- size viewing and printing. Further, the Windows printing
subsystem (prior to Windows 2000) limited printer pages to 32,766 raster lines (approximately
163 inches long for the Printrex printers), so the longest log that could be printed from
Imaging was just 13 feet long. In Windows XP, the Imaging applet was replaced by a new
Paint applet that does print using multiple printer pages. In this case, set the printer page
size to the paper’s page size (8.75 x 6.25 half page), and Paint will generate as many printer
pages as needed to print the log.
In most of the larger geotechnical organizations, proprietary viewers have been written for
internal use by authorized staff and customers. Remarkably, there are very few options for
other users of TIFF log files who are not using Windows XP, or who find the XP Paint
application too primitive.
Printrex welcomes comments regarding requirements and features for log viewing tools,
for possible development of a viewer application for our customers.
5. Every time I start my program, I have to change printer settings. How do I change the
default driver settings?
In Windows 95/98/ME, go to the Start – Settings – Printers folder. Right-click on the printer
icon, and select ‘Properties’. In Windows NT4, right-click on the printer, and select
‘Document Defaults’... not ‘Properties’. In Windows XP/2000, right-click on the printer,
and select ‘Printing Preferences’. (If you select ‘Properties’, go to the ‘General’ tab, and
click the ‘Printing Preferences’ button.
In Windows NT4/2000/XP, changes to the printer settings done from within an application
are generally not saved unless some unusual program coding is done.
6. Self test prints out OK but when I print from the computer I get garbage.
Common problems for this symptom are the parallel cable or the printer driver that is being
used. Be sure the parallel cable is appropriately connected (see section Connecting the
Parallel Cable). Also, be sure the printer driver is for the specific model printer that is being
used.
7. Some times the fan-fold paper skews to one side or the other. How do I correct this?
The Printrex printers are designed to work with a wide
variety of media. A paper skewing problem is
normally corrected by realigning the paper. This
is done by opening the door, straightening the
paper and closing the door. We have found
however, that under some conditions (generally with
very thin paper) the problem may persist. If this is the case, we suggest threading the paper
over a full internal roll of paper (as shown) to remedy the situation.
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
4-1
There is no regular cleaning required for proper operation of the printer, however the
printer surfaces are designed and manufactured to permit cleaning with the following
cleaning agents:
General Cleaning
•
•
•
•
•
Isopropyl alcohol
Ammonia
Chlorine bleach (1:10 concentration with water)
Hexachlorophene (PhisoHex)
Glutaraldehyde (Cidex)
It is recommended that a soft cloth dampened with the cleaning agent be used to clean
the surfaces of the printer. Do NOT submerse or allow spills onto or in the product.
The thermal head incorporates a protective glaze coating and is generally resistant to
harsh environments, however the following precautions should be taken regarding the
thermal head surface:
Protecting the
Thermal Head
•
•
•
•
•
Do not allow the thermal head to come in contact with sharp or hard objects.
Do not allow thermal paper debris to accumulate on the thermal head.
Do not allow condensation to accumulate on the thermal head.
Use only Printrex approved thermal paper
Do not expose the thermal head to abrasive cleansers.
Paper dust or other foreign material may occasionally accumulate on the thermal print
head. This will be indicated by light print or no print in a narrow band down the length of
the paper. In order to eliminate the thermal paper debris buildup, it is recommended to
use a soft cloth moistened with one of the following cleaning agents:
Cleaning The
Thermal Head
•
•
Isopropyl alcohol
Ethanol
A light wiping along the length of the print head is adequate. Allow the print head to dry
before resuming printing. It can be wiped dry with a soft, clean cloth. Do NOT submerse
or allow spills onto the thermal head.
Paper dust or other foreign material may occasionally accumulate on the form sensor.This
will be indicated by missing the top of form position (some time after it has been correctly
stopping at the top of form). The form sensor can be cleaned with an aerosol air spray or
soft bristled brush. It is located just under the form sensor window.
Cleaning The
Form Sensor
With the paper door closed, the thermal head applies a considerable pressure on the
platen (approximately 8 kg). If the printer is stored for long periods of time with the paper
door closed (especially in cold temperatures), it is possible that a slight flat area is induced
in the platen. It is recommended the paper door be kept in an unlatched condition for
extended periods of storage. Note:The condition of a flat spot on the platen is not permanent
and the platen will return to it’s normal roundness after 10 or so minutes of resumed
operation.
Long Term
Storage
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Support / Service
5-1
Printrex products are warranted to be free from failures due to defects in material and
workmanship for twelve (12) months from the date of purchase. During this 12 month
period Printrex will, at its sole discretion, replace or repair at no charge the product which,
in its opinion, is defective.
Warranty
If the failed product has been modified without Printrex’s consent or if the failure is the
result of misuse, abuse or misapplication, Printrex has no obligation to repair or replace the
failed product.
Consumables Warranty: Printrex warrants that the thermal print head will be free from
defects for the Expected Life of the printhead but not more than one (1) year from the date
of purchase. The Expected Life of the printhead is considered to be the lesser of, A) fifty (50)
8
kilometers of delivered media or B) one hundred million (10 ) pulses of an individual print
element (approximately 12.7 km of converted printout for any given print element).
Except as expressly provided above, the hardware and accompanying written materials
(including the User’s Guide) are provided ‘as is’ without warranty of any kind, including the
implied warranties of merchantability and fitness for a particular purpose, even if Printrex
has been advised of that purpose. In no event will Printrex be liable for any direct, indirect,
consequential, or incidental damages arising out of the use of or inability to use such product
even if Printrex has been advised of the possibility of such damages. Some states do not
allow the exclusion or limitation of liability for consequential or incidental damages, so the
above limitation may not apply.
Following the warranty period Printrex will repair defective products and will charge a fee
to cover handling and service costs based on Printrex’s then-current price schedule.
Service Policy
Before returning a failed unit, the buyer must first obtain a Return Material Authorization
(RMA) number by contacting Printrex’s Customer Service. The RMA number should be
prominently displayed on the outside of the returned package and on the accompanying
packing list. Printrex cannot be held responsible for any package returned without an RMA
number. The model and serial number of the printer is on the chassis label located on the
rear of the printer. Please have this information available when service is required.
Obtaining Service
The user is responsible for packing the failed product in original or equivalent packaging
for shipment, and for the charges to ship the failed product to Printrex. Printrex is responsible
for charges to ship the repaired or replaced product if under warranty. If any charge to you
is involved, Printrex, at its sole option, will bill you or return the product C.O.D.
Printrex recognizes that some customers have service departments that are capable of
servicing the Printrex products. For this case, Printrex offers a Self Service Reference. This
reference includes assembly drawings with bills of material so that replaceable internal
components can be identified and ordered. Please contact Printrex Customer Service to
obtain a Self Service Reference for your product(s). For self service, the owner assumes the
risk of damage to the unit and may violate the warranty.
Self Service
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Support / Service
5-2
A list of service centers are available from the Printrex web site. Please refer to:
Service Centers
Spare Parts
Description .................................................................................................. Part Number
Paper Carrier ................................................................................................... 2111-0189
Paper Rod........................................................................................................ 2012-0008
Power Cord (Central Europe plug) ................................................................... 2237-0004
Power Cord (United Kingdom plug)................................................................. 2237-0061
Power Cord (United States plug)...................................................................... 2237-0007
Print Head Assembly ....................................................................................... 2111-0175
Description .................................................................................................. Part Number
Supplies
Roll Paper, 150’ length .................................................................................... 2316-0001
Roll-FF Paper, 150’ roll (6 1/4” Perf. Intervals) ................................................. 2316-0013
Fan-Fold Paper, 8.75 x 6.25 inch, 800 sheet box ............................................. 2316-0011
Roll Matte Film, 117’ length ............................................................................ 2316-0009
Description .................................................................................................. Part Number
Accessories
USB Adapter Kit .............................................................................................. 2012-0030
Paper Tray (Bottom feed tray, for 840DL/G and 820DL/G) ............................... 2320-0014
Description .................................................................................................. Part Number
Additional
Documentation
Driver Installation Guide, Win2000/XP ........................................................... 1028-0061
Driver User Guide, Win2000/XP ..................................................................... 1028-0062
Self Service Guide, 840DL/G DT Chassis ........................................................ 1028-0073
Self Service Guide, 820DL/G DT Chassis ........................................................ 1028-0075
Self Service Guide, 820G DT Chassis.............................................................. 1028-0077
Self Service Guide, 810 DT Chassis ................................................................ 1028-0079
System Administrators’ Guide ......................................................................... 1028-0063
WindowsTM Drivers
Windows drivers are available from the Printrex Web Site. Please refer to:
Printrex, Inc.
276 East Gish Road
San Jose, CA 95112-4703 USA
Contact
Information
Telephone: +408.573.1200
Fax:
+408.573.1600
E-mail:
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
6-1
Use this equipment only for its intended use as described in this guide.
Restriction on Use
•
•
•
•
Do not use power supplied outside the specified voltage/hertz range.
Do not block any openings on the equipment.
Do not use corrosive chemicals or vapors on the equipment.
Do not expose equipment to rain or spills or moisture.
This equipment must be grounded to conform with the normative safety standards. Connect
only to a properly grounded outlet.
Grounding
The power cord supplied with the equipment is rated and approved for service to this
equipment.
Power Cord
•
•
•
Do not operate the equipment if it has a damaged power cord or plug.
Do not immerse the power cord or plug in water.
Do not use a power cord other than that supplied with the equipment.
There are no user-serviceable parts inside the equipment. Refer all service to a qualified
service technician.
Serviceability
Regulatory
Compliance
FCC Compliance
This unit has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.
CE Compliance
The manufacturer declares that this product conforms to the following standards or other
normative documents:
EMC:
EN 55022:1994 Limits and Methods of Measurements of Radio Interference
Characteristics of Information Technology Equipment, Class A, including
amendments A1:1995, A2:1997
EN 50024:1998 Limits and method of measurement of Immunity
characteristics of Information technology equipment
Safety: EN 60950:1992 Safety of information technology equipment including
electrical business equipment, including amendments A1:1993, A2:1993,
A3:1995, A4:1997, A11:1997
DT Chassis Printers/Plotters
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
7-1
Power Requirements (840DL/G) ............................... 100-240 VAC, 500 VA, 50~60Hz
Power Requirements (820DL/G and 820G) .............. 100-240 VAC, 240 VA, 50~60Hz
Power Requirements (810) ........................................ 100-240 VAC, 150 VA, 50~60Hz
Height ................................................................................................4.5 inch (114 mm)
Width .............................................................................................. 12.2 inch (310 mm)
Depth .............................................................................................. 12.4 inch (315 mm)
Unit Weight.............................................................................................. 14 lbs (6.4 kg)
Shipping Weight ...................................................................................... 18 lbs (8.2 kg)
Interface ...........................................................................................High Speed Parallel
General
Specifications
Print Speed (840DL/G) ........................................................................ 0.5 to 4 inch/sec
Print Speed (820DL/G and 820G) ....................................................... 0.5 to 2 inch/sec
Print Speed (810) ................................................................................. 0.5 to 1 inch/sec
Horizontal Resolution .................................................................... 203 dpi (8 dots/mm)
Vertical Resolution ......................................................................... 203 dpi (8 dots/mm)
Performance
Overall Forms Width ...................................................................... 8.75 inch (222 mm)
Internal Roll Capacity................................................... 2.6 inch (66 mm) diameter roll
For 840DL/G and 820DL/G:
Bottom Feed Roll Capacity.....................................5 inch (152 mm) diameter roll
Bottom Feed Fan-fold Capacity ............................. 18 inch (457 mm) stack height
Forms Mark ............................................ See Section 3-3 for forms mark specifications
Forms
Compatibility
o
o
o
o
Storage Temperature ....................................................... -40 C (-40 F) to 60 C (140 F)
Environmental
Regulatory
o
o
o
o
Operating Temperature (non-condensing) ......................... 5 C (41 F) to 40 C (104 F)
Shock & Vibration (non-operational) ........................................ 3G, 0 to 50 Hz, 3 axes
Environmental Ingress (IEC 529) ............................................................................. IP54
CE ............................................................................................... ITE Directive, Edition 2
FCC ...................................................................................................................... Class A
Information in this document is subject to change without notice and does not represent a commitment on the part of
Printrex, Inc. No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other
than the purchaser’s personal use, without the expressed written permission of Printrex, Inc.
All rights reserved. Printed in the United States of America.
© Copyright 2003 by Printrex, Inc.
Part Number: 1028-0071 Rev 1
Printrex • 276 East Gish Road • San Jose, CA 95112-4703 • Ph: (408) 573-1200 • Fax: (408) 573-1600 • www.printrex.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|