TM
CALS
WRE
PO
AL
WRESMANU
O
tre
vre
384DitAalgCon
A
D
CONTENTS
(click on a topic to view)
Congratulations
Wiring
Features and Specifications
Operation
Inputs / Outputs
Block Diagram
Troubleshooting
Warranty
Installation
Wiring
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES / SPECIFICATIONS
PWM Power Supply
True 24-bit Digital Signal Processing
Class "A" Analog Stages
Direct-Coupled Analog Circuitry
Dual RCA Outputs
Analog Pass-Through
Smart Input Selection
Gold Plated RCA Input and Output Connectors
Optical and Coax Digital Inputs
Completely Designed And Handcrafted In The USA
Three Year Warranty when installed by an
Authorized PrecisionPower Dealer
Specifications
Oversampling
8 fs
Frequency Response:
Total Harmonic Distortion:
Channel Separation
Digital Inputs :
5 Hz - 20 kHz ±0.2dB
<0.01 %
>90dB
Coaxial and Toslink Optical
11 - 15 volts
4 VRMS
Supply Voltage
Maximum Output (10kΩ Load)
Output Impedance
Dimensions
30 ohms
5.125" W
13.11" L
1.750" H
1
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
OPERATION
PrecisionPower's DAC-348 processes the digital signal directly from
the CD player, changer or other digital source. All digital to analog
conversion as well as the subsequent filtering and analog treatment
of the signal by the stock source unit is replaced by the superior digital
signal processing, digital to analog conversion and fully discrete Class
A analog circuitry of the DAC-348.
Because most digital head units are in fact combined with analogAM/
FM and Cassette players, PrecisionPower engineers have included
analog inputs as well as a Smart Input Selector that monitors the
Digital inputs and automatically chooses the appropriate source. To
take advantage of this feature you must connect both the Digital
(coaxial or optical) and the analog (RCA) outputs to the DAC-348.
As you have now bypassed the stock circuitry, the volume control on
your head unit will no longer affect the digital signal. You will need to
use a preamp or line driver (such as the PAR-245) as the master
volume control for your system. Refer to the diagram below.
System Diagram
Source Unit
eject
1
5
2
6
3
7
4
8
Trk 1
PPI MAR KET ING DPT
Analog RCA
BASS
TREBLE
BALANCE
TRACK
VOLUME
LEFT
RIGHT
FOWARD
REVERSE
Digital
Coaxial RCA
Or Optical
R
DAC-348
Digital to Analog
Convertor
Input
L
R
Input Sentiy
Rear
Output
L
R
Front
utput
O
L
LED Select
1
Power
2
Frequency Adjust
3
4
Sub
Precision
PAR-245
Volum
Power
Low
Power
Ini
Low-Mid
F
High-Mid
R
Treble
+
er
Made in USA
+
Defeat
+
+
+
i
d
re
PAR-245
PAR-245
Preamp/Equalizer
Front Output
™
Rear Output
POWERCLASS Amplifier
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
INSTALLATION / MOUNTING
Mounting
To prevent damage to the DAC while driving, mount it in a
secure place. Choosing the appropriate location will depend
upon your vehicle and the complexity of your system design.
Keep in mind that the output of the DAC-348 must go to a
preamp to control the volume of the digital source. To keep the
signal path as short as possible, the DAC-348 should be
mounted as close to the head unit and preamp as possible.
Never mount the DAC-348 in a location that would subject it to
immersion or exposure to water.
Once a location has been chosen, securely mount the
DAC-348 with four mounting screws. Be Careful! Inspect the
area underneath to be sure you are not drilling into wires, brake
or fuel lines, etc. that could be damaged by the drill bit or screws.
Dimensions
5.125" W
13.113
13.11" L
1.750" H
12.656
4.415
5.125
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
WIRING
Factory Ground wire may
need to be replaced if it is
frayed or broken.
Positive
Battery
Terminal
Fuse must be
installed within
18" of battery
Run signal cables (RCAs)
and remote turn-on lead
down the opposite side of
the vehicle from the power
wire to avoid radiated noise.
Drill a hole in the firewall
and use a rubber grommet
to keep wire from shorting.
eject
1
5
2
6
3
7
4
8
Trk
1
DP
B
A
S
S
TREBLE
B
A
L
A
N
C
E
T
R
A
C
K
P
P
I
M
A
R
K
E
T
I
N
G
T
VOLUME
L
E
F
T
R
I
G
H
T
F
O
W
A
R
D
REVERSE
Mount the DAC-348 near
the front of the vehicle to
minimize signal path lengths
Power distribution block.
Run the cables under the
carpet near the side of the
vehicle. Be careful not to
drill or screw into the wires
when you replace the trim.
Avoid sharp edges that
could chafe through the
insulation.
For systems over 300 watts,
add a ground cable from the
amp to the battery.
Attach Ground Wires
firmly to solid metal.
NOTE
Before beginning, disconnect the negative (-) terminal of the
battery prior to working on the positive (+) terminal to prevent
a short to ground. This is important, unless you want to spend
the rest of your life with a nickname like "Sparky," or "Smokey."
Reconnect the negative terminal only after all connections have
been made.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
WIRING
The next step is to connect the Power, Ground, and Remote wires to
your DAC-348. The power wire should run from the mounting location
through the vehicle to the battery or power distribution block. Avoid
sharp corners, creases, and sharp body parts. When passing through
any metal wall (i.e. firewall etc.), a grommet must be used to prevent
the wire from chaffing and shorting to ground.
The ground wire should be of the same gauge as the power wire. As
a rule of thumb, use as short a length of wire as possible.
Find a location near the DAC that is metal (the floor is ideal) and
clean an area about the size of a quarter to bare metal. Drill a pilot
hole in the middle of this area. Be Careful! Inspect the area underneath
to be sure you are not drilling into wires, brake or fuel lines, etc.
Terminate the wire with a ring connector and attach it to the bare
metal using a #8 sheet metal screw and washer (not supplied). We
suggest crimping and/or soldering this connection.After the connection
is complete, coat the area with silicone or some similar material to
Powerlock
prevent rust from developing.
Finally, the remote wire needs to
run to the power antenna (or
amplifier remote) lead of the head
unit. This wire supplies a 12 volt
signal to the DAC-348 when the
main system is activated.
Once you have routed the power,
ground, and remote wires through
the vehicle, it is time to connect the wires to the DAC-348. Be sure
that you have not reconnected the ground cable to the negative post
of the battery.
Cut off excess wire and, using wire strippers, strip the power, ground
and remote cables about 1/8 inch. Locate the power, ground, and
remote Powerlock connector (supplied). On the top of the connector
are three slotted screws. With a small flat-bladed screwdriver, loosen
the screws before attempting to insert the cables. After you have
inserted the stripped end of each cable into the connector, secure it
by tightening the associated screw. Check that each connection is
tight. If the wires are secure, the connector may be plugged into the
DAC-348.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
INPUTS / OUTPUTS
1 Connect the Digital output from your source to the appropriate
Digital Input connector (coax or Toslink optical).
After connecting Power, Ground, and Remote wires, plug in the
2
Powerlock connector here.
3
5 amp Fuse
Parallel Analog Outputs to Preamp.
Analog Inputs from source unit.
A
B
C Sync LED - Red light indicates digital signal being processed.
Power LED - Red light indicates power on.
D
Analog Outputs
L
Analog Inputs
L
L
A
B
B
A
R
R
R
Sync Power
A
A
C
D
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
BLOCK DIAGRAM
Smart Input Selector
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
TROUBLE SHOOTING
NO SOUND
IS THE POWER LED LIT?
YES
YES
NO
Check Power and Remote turn-on wire
for voltage. Make sure Ground wire is
secure.
IS THE SYNC LED LIT?
NO
Unplug the Digital Input cable
from the DAC-348
Bypass the DAC-348 by connecting
the analog RCA input cables directly
to the Preamp (PAR-245).
ANY SOUND NOW?
YES
NO
Problem is in the DAC. See your
local Authorized PrecisionPower
Dealer or call 1-800-62POWER.
Problem is elsewhere in the system.
Check head unit and amplifiers.
ANY SOUND NOW?
NO
YES
Problem is in the DAC. See your
local Authorized PrecisionPower
Dealer or call 1-800-62POWER.
Problem is elsewhere in the system.
Check head unit and amplifiers.
SOUND IN ONE CHANNEL ONLY
IS THE SYNC LED LIT?
YES
NO
Check Balance control. Reverse left
and right RCA inputs
SOUND IS NOW IN
SAME CHANNEL
Problem is in the RCA cables
OPPOSITE CHANNEL
Problem is in the head unit or RCA
cables
Reverse left and right RCA outputs
SOUND IS NOW IN
OPPOSITE CHANNEL
SAME CHANNEL
Problem is downstream of the
DAC-348
Problem is in the DAC. See your
local Authorized PrecisionPower
Dealer or call 1-800-62POWER.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
WARRANTY
Three-Year Limited U.S.A. Warranty
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. PrecisionPower warrants its products to be free from defects in materials and
workmanship under normal use and service for a period of three (3) years from the date of
original purchase when the unit is installed by an Authorized Dealer. Non-Authorized Dealer
installed products carry a one (1) year parts and ninety (90) days labor limited warranty. The
extent and conditions of Limited Warranty are as follows:
1. Authorized Dealer Installed Products: PrecisionPower will either repair or replace at no charge,
to the original purchaser, any unit which PrecisionPower’s examination discloses to be defective
and under warranty, provided the defect occurs within three (3) years from the date of original
purchase when the unit is installed by an Authorized Dealer and the product is returned immedi-
ately to PrecisionPower. This warranty is not transferable.
2. Non-Authorized Dealer Installed Products: PrecisionPower will either repair or replace at no
charge, to the original purchaser, any unit which PrecisionPower’s examination discloses to be
defective and under warranty, provided the defect occurs within ninety (90) days from the date of
purchase and the product is returned immediately to PrecisionPower. Warranty claims beyond
ninety (90) days for Non-Authorized Dealer Installed Products will be for parts only and will
extend for one (1) year from the date of purchase. This warranty is not transferable.
3. The date of purchase and proof of Authorized Dealer Installation of a PrecisionPower product
must be established by an original sales receipt which must accompany the article being re-
turned for warranty work.
4. This warranty shall NOT apply to any PrecisionPower product found to have the original fac-
tory serial number removed or defaced. All products received (by PrecisionPower) for in war-
ranty or out of warranty repair, with their original serial numbers removed or defaced, will NOT be
repaired and will be returned to sender, freight collect. Refer to original packaging for the serial
number of your component speakers.
5. The provisions of this warranty shall not apply to any PrecisionPower product used for a
purpose for which it is not designed, which has been repaired or altered in any way, or which has
been connected, installed, or adjusted other than in accordance with the instructions furnished in
PrecisionPower’s owner’s manual. Nor shall this warranty apply to any part which has been
subject to misuse, neglect, or accident.
6. PrecisionPower does not authorize any other persons to assume any other liability in connec-
tion with its products. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY MADE BY
PRECISIONPOWER APPLICABLE TO ITS PRODUCTS. ANY IMPLIED WARRANTY OR MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO
PRECISIONPOWER PRODUCTS IS LIMITED IN DURATION TO THE DURATION OF THIS
LIMITED WARRANTY. PRECISIONPOWER SHALL NOT BE LIABLE FOR THE INCIDENTAL,
CONSEQUENTIAL, OR COMMERCIAL DAMAGES RESULTING FROM THE BREACH OF THIS
WRITTEN WARRANTY. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages or limitations on how long an implied warranty lasts; so the
above limitations or exclusions may not apply to you.
7. Your product will be serviced on an in-warranty basis within the warranty period for the correc-
tion of warranted defects. If improper operation of your PrecisionPower product should occur,
contact your Authorized Dealer for assistance with the return and factory repair of your
PrecisionPower
product. If an Authorized Dealer is not available, return the unit including your name, telephone
number, return address, a copy of your sales receipt, and a description of the problem to:
PrecisionPower,Inc.
Service Department
4829 S. 38th Street
Phoenix, AZ 85040-2964
TO RETURN PRECISIONPOWER PRODUCTS OUT OF WARRANTY: Return the unit, postage
prepaid, in the original protective carton. Please include a description of the problem and, if
desired, a request for an estimate of repair costs. Unless a request for an estimate is included,
the unit will be repaired as necessary. Please contact PrecisionPower Customer Service at 1-
800-62-POWER for questions concerning out of warranty repair charges. Repaired unit will be
returned with an itemized statement, C.O.D.
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
|