R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1--800--554--6723
Operator’s Manual
Manual del Operador
Manuel de L’utilisateur
2250 / 2450 / 2550
U
R L
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual del operador y siga todas las advertencias e enstruc-
ciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Augusta, GA 30907
Copyright E2000 WCI Outdoor Products, Inc.
530087722
1/19/00
Download from Www.Somanuals.com. All Manuals Search And Download.
S Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.
Kickback Path
S Store the unit and fuel in an area where
fuel vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.
KICKBACK
Avoid Obstructions
WARNING: Kickback can occur when
the moving chain contacts an object at the
upper portion of the tip of the guide bar or
when the wood closes in and pinches the
saw chain in the cut. Contact at the upper
portion of the tip of the guide bar can cause
the chain to dig into the object, which stops
the chain for an instant. The result is a light-
ning fast, reverse reaction which kicks the
guide bar up and back toward the operator.
If the saw chain is pinched along the top of
the guide bar, the guide bar can be driven
rapidly back toward the operator. Either of
these reactions can cause loss of saw con-
trol which can result in serious injury. Guard
against kickback.
Clear The Working Area
REDUCE THE CHANCE OF
KICKBACK
S Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
Rotational Kickback is the rapid upward
and backward motion of the chain saw that
can occur when moving saw chain near the
upper portion of the tip of the guide bar
contacts an object such as a log or branch.
S Never let the moving chain contact any
object at the tip of the guide bar.
S Keep the working area free from obstruc-
tions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate or
avoid any obstruction that your saw chain
could hit while you are cutting through a
particular log or branch.
Pinch-Kickback and Pull-In occur when
the chain is suddenly stopped by being
pinched, caught, or by contacting a foreign
object in the wood. This sudden stopping of
the chain results in a reversal of the chain
force used to cut wood and causes the saw
to move in the opposite direction of the
chain rotation. Pinch-Kickback drives the
saw straight back toward the operator. Pull-
In pulls the saw away from the operator. Ei-
ther reaction can result in loss of control and
serious injury.
S Keep your saw chain sharp and properly
tensioned. A loose or dull chain can in-
crease the chance of kickback occurring.
Follow manufacturer’s chain sharpening
and maintenance instructions. Check
tension at regular intervals with the en-
gine stopped, never with the engine run-
ning. Make sure bar clamp nuts are se-
curely tightened after tensioning chain.
S Begin and continue cutting at full speed. If
chain is moving at a slower speed, there is
greater chance of kickback occurring.
S Cut one log at a time.
Avoid Pinch---Kickback:
S Be extremely aware of situations or ob-
structions that can cause material to
pinch the top of or otherwise stop chain.
S Do not cut more than one log at a time.
S Do not twist the saw as the bar is with-
drawn from an undercut when bucking.
S Use extreme caution when re-entering a
previous cut.
S Do not attempt cuts starting with the tip of
the bar (plunge cuts).
A v o i d P u l l --- I n :
S Watch for shifting logs or other forces that
could close a cut and pinch or fall into
chain.
S Always begin cutting with the engine at
full speed and the saw housing against
wood.
S Use the Reduced---Kickback Guide Bar
and Low---Kickback Chain specified for
your saw.
S Use wedges made of plastic or wood.
Never use metal to hold the cut open.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S Reduced---Kickback Guide Bar, designed
with a small radius tip which reduces the
size of the kickback danger zone on the
bar tip. A Reduced---Kickback Guide Bar
has been demonstrated to significantly
reduce the number and seriousness of
kickbacks when tested in accordance
with safety requirements for gasoline
powered chain saws as set by ANSI
B175.1.
MAINTAIN CONTROL
Stand to the left of
the
S Low---Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter.
Low---Kickback Chain has met kickback
performance requirements when tested
on a representative sample of chain saws
below 3.8 cubic inch displacement speci-
fied in ANSI B175.1.
Never reverse hand positions
S Handguard, designed to reduce the
chance of your left hand contacting the
chain if your hand slips off the front han-
dlebar.
S Position of front and rear handlebars, de-
signed with distance between handles
and “in-line” with each other. The spread
and “in-line” position of the hands pro-
vided by this design work together to give
balance and resistance in controlling the
pivot of the saw back toward the operator
if kickback occurs.
Elbow locked
Thumb on underside of
handlebar
Reduced Kickback Symmetrical Guide Bar
S Keep a good, firm grip on the saw with
both hands when the engine is running
and don’t let go. A firm grip will help you
reduce kickback and maintain control of
the saw. Keep the fingers of your left hand
encircling and your left thumb under the
front handlebar.
Small Radius Tip
S Keep your right hand completely around
the rear handle whether your are right
handed or left handed. Keep your left arm
straight with the elbow locked.
Symm
S Position your left hand on the front han-
dlebar so it is in a straight line with your
right hand on the rear handle when mak-
ing bucking cuts. Never reverse right and
left hand positions for any type of cutting.
S Stand with your weight evenly balanced
on both feet.
Large Radius Tip
Contoured Depth Gauge
Elongated Guard Link
Deflects
S Stand slightly to the left side of the saw to
keep your body from being in a direct line
with the cutting chain.
Kickback Force
And Allows Wood
To Gradually
Low---Kickback Chain
Ride Into Cutter
S Do not overreach. You could be drawn or
thrown off balance and lose control of the
saw.
S Do not cut above shoulder height. It is dif-
ficult to maintain control of saw above
shoulder height.
Can Obstruct Material
Chain With High Kickback Potential
KICKBACK SAFETY FEATURES
ANSI B175.1-1991 “American National
Standard for Powered Tools --- Gasoline
Powered Chain Saw --- Safety Require-
ments.”
NOTE: If this saw is to be used for commer-
cial logging, you must order and install a
chain brake to comply with Federal OSHA
Regulations for Commercial Logging. Con-
tact your Authorized Service Dealer or call
1-800-554-6723.
WARNING: The following features are
included on your saw to help reduce the
hazard of kickback; however, such features
will not totally eliminate this dangerous reac-
tion. As a chain saw user, do not rely only on
safety devices. You must follow all safety
precautions, instructions, and maintenance
in this manual to help avoid kickback and
other forces which can result in serious
injury.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of shipping spacer
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline
powered hand tools could cause blood
vessel or nerve damage in the fingers,
hands, and joints of people prone to
circulation disorders or abnormal swellings.
Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the
fingers, hands, or joints, discontinue the
use of this tool and seek medical attention.
An anti-vibration system does not
guarantee the avoidance of these
problems. Users who operate power tools
on a continual and regular basis must
monitor closely their physical condition and
the condition of this tool.
Clamp
Nuts
Bar Cl
Assembly Tool
S An adjusting pin and screw are used to
adjust the tension of the chain. It is very
important when assembling the bar that
the pin located on the adjusting screw
aligns with a hole in the bar. Turning the
screw will move the adjustment pin up
and down the screw. Locate this adjust-
ment pin before you begin mounting the
bar onto the saw. See illustration below.
SPECIAL NOTICE: Your saw is
equipped with
a
temperature limiting
muffler and spark arresting screen which
meets the requirements of California Codes
4442 and 4443. All U.S. forest land and the
states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and
Inside view of
Bar Clamp
Washington
require
many
internal
combustion engines to be equipped with a
spark arrestor screen by law. If you operate
a chain saw in a state or locale where such
regulations
exist, you are legally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
section for maintenance of the Spark
Arrestor.
Adjustment screw
S Turn the adjusting screw counterclock-
wise to move the adjusting pin almost as
far as it will go to the rear. This should al-
low the pin to be near the correct position.
Further adjustment may be necessary as
you mount the bar.
Failure to follow all Safety Rules and Precau-
tions can result in serious injury. If situations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your retailer or call
1-800-554-6723.
S Mount the bar as illustrated.
S Slide the bar toward the rear of the saw as
far as possible.
S Prepare the chain by checking the proper
direction. Without following the illustration
it is easy to place the chain on the saw the
wrong direction. Use the illustration of the
chain to determine the proper direction.
S Place the chain onto the sprocket located
behind the clutch drum. Fit the chain be-
tween the teeth in the sprocket.
ASSEMBLY
The assembly tool provided with your saw is
the only tool needed for assembly. Protec-
tive gloves (not provided) should be worn
during assembly.
S Start at the top of the bar and fit chain into
groove around the guide bar.
ATTACHING THE BAR & CHAIN (If not
already attached)
S Pull the bar forward until the chain is snug
in the groove of the bar.
WARNING: Recheck each assembly
step if the saw is received assembled. Al-
ways wear gloves when handling the chain.
The chain is sharp and can cut you even
when it is not moving!
S Hold guide bar against the saw frame and
install bar clamp. Make sure the adjusting
pin is aligned with the hole in the bar. Re-
member this pin moves the bar forward
and backward as the screw is turned.
S Replace the bar clamp nuts and tighten
finger tight. Once the chain is tensioned
you will need to tighten bar clamp nuts.
S Loosen and remove the clamp nuts and
the bar clamp from the saw.
S Remove the plastic shipping spacer (if
present).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Mount the Bar
Tip of Bar
Bar Clamp Nuts
Guide Bar
FUELING & LUBRICATION
FUELING ENGINE
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good quality
2-cycle air-cooled engine oil.
We
Place chain onto the sprocket
recommend Poulan/Weed Eater brand oil. If
you do not use this oil, use a good quality
2-cycle air-cooled oil designed to be mixed
at a ratio of 40:1 (A 40:1 ratio is obtained by
mixing 3.2 onces of oil with 1 gallon of
unleaded gasoline). When mixing fuel
follow the instructions printed on the
container. Always read and follow the safety
rules relating to fuel before fueling your unit.
CHAIN TENSION (Including units with
chain already installed)
NOTE: When adjusting chain tension,
make sure the bar nuts are finger tight only.
Attempting to tension the chain when the
bar nuts are tight can cause damage.
Checking the tension:
Use the screwdriver end of the combination
screwdriver/wrench tool to move the chain
around the bar. If the chain does not rotate, it
is too tight. If too loose, the chain will sag be-
low the bar.
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubri-
cation. Lubrication is provided by the auto-
matic oiler system when the oil tank is kept
filled. Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shown by smoke coming from the chain
and/or discoloration of the bar.
In freezing weather oil will thicken, making it
necessary to thin bar and chain oil with a
small amount (5 to 10%) of #1 Diesel Fuel or
kerosene. Bar and chain oil must be free
flowing for the oil system to pump enough
oil for adequate lubrication.
Adjusting the tension:
Chain tension is very important. Chain
stretches during use. This is especially true
during the first few times you use your saw.
Always check chain tension each time you
use and refuel your saw.
You can adjust chain tension by loosening
the bar clamp nuts and turning the adjust-
ing screw 1/4 of a turn while lifting up on bar.
S If chain is too tight, turn adjusting
screw 1/4 turn counterclockwise.
S If chain is too loose, turn adjusting
screw 1/4 turn clockwise.
Genuine POULAN or POULAN PRO bar
and chain oil is recommended to protect
your unit against excessive wear from heat
and friction. POULAN or POULAN PRO oil
S Lift up the tip of the bar and tighten the bar
clamp nuts with the combination screw-
driver/wrench.
resists high temperature thinning.
If
POULAN or POULAN PRO bar and chain oil
is not available, use a good grade SAE 30
oil.
S Recheck chain tension.
S Never use waste oil for bar and chain lu-
brication.
S Always stop the engine before removing
the oil cap.
Fuel mix cap
Chain moves freely
Oil Cap
Lifts only 1/8 of an inch from bar.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
S Allow the engine to run for approximately
five seconds. Then, squeeze and release
throttle trigger to allow engine to return to
idle speed.
STARTING
WARNING: The chain must not move
when the engine runs at idle speed. If the
chain moves at idle speed refer to CARBU-
RETOR ADJUSTMENT within this manual.
Avoid contact with the muffler. A hot muffler
can cause serious burns.
To stop the engine move the switch to the
STOP or OFF position.
To start the engine hold the saw firmly on
the ground as illustrated. Make sure the
chain is free to turn without contacting any
object.
For a warm engine:
S Pull the choke/fast idle lever out to the full
extent, then push the choke/fast idle lever
back in completely (to the OFF CHOKE
position).
S Slowly press the primer bulb six times.
S Pull the starter rope quickly with your right
hand until the engine starts.
S Squeeze and release throttle trigger, al-
lowing engine to idle.
Difficult starting or flooded engine:
The engine may be flooded with too much
Use only 15”---18” of rope per pull.
Hold saw firmly while pulling starter rope
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ignition
switch is in the ON or START position.
Starting could require pulling the starter
rope handle many times depending on how
badly the unit is flooded. If engine fails to
start, refer to troubleshooting chart or call
1-800-554-6723.
CUTTING METHODS
Important points to remember
When pulling the starter rope, do not use
the full extent of the rope as this can
cause the rope to break. Do not let starter
rope snap back. Hold the handle and let
the rope rewind slowly.
For cold weather starting, start the unit at
FULL CHOKE; allow the engine to warm
up before squeezing the throttle trigger.
Do not cut material with the choke/fast idle
lever at the FULL CHOKE position.
For cold engine or warm engine after
running out of fuel:
IMPORTANT POINTS
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials,
etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary.
S Keep the chain out of dirt and sand. Even
a small amount of dirt will quickly dull a
chain and thus increase the possibility of
kickback.
NOTE: In the following steps, when the
choke/fast idle lever is pulled out to the full
extent, the correct throttle setting for starting
is set automatically.
S Practice cutting a few small logs using the
following techniques to get the “feel” of
using your saw before you begin a major
sawing operation.
S Squeeze throttle trigger and allow engine
to reach full speed before cutting.
S Begin cutting with saw frame against log.
S Keep the engine at full speed the entire
time you are cutting.
ON/STOP
Switch
Primer
Bulb
S Allow chain to cut for you. Exert only light
pressure. If you force the cut, damage to
bar, chain, or engine can result.
S Move switch to the START or ON position.
S Pull the choke/fast idle lever out to the full
extent.
S Release the throttle trigger as soon as the
cut is completed, allowing the engine to
idle. If you run the saw at full throttle with-
out a cutting load, unnecessary wear can
occur to the chain, bar, and engine.
S To avoid losing control when cut is com-
plete, do not put pressure on the saw at
the end of the cut.
Choke Lever
S Stop the engine before setting the saw
down after cutting.
S Slowly press the primer bulb six times.
S Pull the starter rope quickly with your right
hand 5 times, then push the choke/fast
idle lever in completely (to the OFF CHO-
KE position).
TREE FELLING TECHNIQUES
Carefully plan your sawing operation in ad-
vance. Clear the work area. You need a
clear area all around the tree so you can
have secure footing. Study the natural con-
S Pull the starter rope quickly with your right
hand until the engine starts.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ditions that can cause the tree to fall in apar-
ticular direction.
Natural conditions that can cause a tree to
fall in a particular direction include:
Final cut here. 2 inches above
center of notch.
First cut
S The wind direction and speed.
S The lean of the tree. The lean of a tree
might not be apparent due to uneven or
sloping terrain. Use a plumb or level to
determine the direction of tree lean.
S Weight and branches on one side.
S Surrounding trees and obstacles.
Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator. Check for broken or dead
branches which can fall on you while
cutting.
Make sure there is enough room for tree to
fall. Maintain a distance of 2-1/2 tree lengths
from the nearest person or other object. En-
gine noise can drown out a warning call.
Remove dirt, stones, loose bark, nails, sta-
ples, and wire from the tree where cuts are
to be made.
Notch
Second cut
S After removing the cutout of wood, make
the felling cut on the opposite side of the
notch. This is done by making a cut about
two inches higher than the center of the
notch. This will leave enough uncut wood
between the felling cut and the notch to
form a hinge. This hinge will help prevent
the tree from falling in the wrong direction.
Hinge holds tree
on stump and
Plan aclear retreat path to the rear and diag-
onal to the line of fall.
helps control fall
Opening of
felling cut
Plan a clear retreat path
Closing of
notch
Direction of Fall
NOTE: Before felling cut is complete, use
wedges to open the cut when necessary to
control the direction of fall. Use wood or
plastic wedges, but never steel or iron, to
avoid kickback and chain damage.
S Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell-
ing cut, or movement in upper branches.
S As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
45_
WARNING: Do not cut near buildings or
electrical wires if you do not know the direc-
tion of tree fall, at night since you will not be
able to see well, or during bad weather such
as rain, snow, or strong winds. etc.
FELLING LARGE TREES
S Be extremely cautious with partially fallen
trees that may be poorly supported.
When a tree doesn’t fall completely, set
the saw aside and pull down the tree with
a cable winch, block and tackle, or tractor.
To avoid injury, do not cut down a partially
fallen tree with your saw.
(6 inches in diameter or larger)
The notch method is used to fell large trees.
A notch is cut on the side of the tree in the
desired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.
NOTE: If the tree has large buttress roots,
CUTTING A FALLEN TREE
remove them before making the notch.
(BUCKING)
Bucking is the term used for cutting a fall-
en tree to the desired log size.
NOTCH CUT AND FELLING THE
TREE
WARNING: Do not stand on the log be-
ing cut. Any portion can roll causing loss of
footing and control. Do not stand downhill
of the log being cut.
S Make notch cut by cutting the top of the
notch first. Cut through 1/3 of the diameter
of the tree. Next complete the notch by
cutting the bottom of the notch. See illus-
trated. Once the notch is cut remove the
notch of wood from the tree.
IMPORTANT POINTS
S Cut only one log at a time.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
S Cut shattered wood very carefully; sharp
pieces of wood could be flung toward op-
erator.
First cut on pressure side of log
S Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cutting and never hold the log with your
leg or foot.
Second cut
Second cut
S Do not cut in an area where logs, limbs,
and roots are tangled such as in a blown
down area. Drag the logs into a clear area
before cutting by pulling out exposed and
cleared logs first.
S Make the first bucking cut 1/3 of the way
through the log and finish with a2/3 cut on
the opposite side. As the log is being cut,
it will tend to bend. The saw can become
pinched or hung in the log if you make the
first cut deeper than 1/3 of the diameter of
the log.
First cut on pressure side of log
BUCKING USING A LOG OR SUP-
PORT STAND
S Remember your first cut is always on the
pressure side of the log.
S Give special attention to logs under strain
to prevent the saw from pinching. Make
the first cut on the pressure side to relieve
the stress on the log.
(Refer to the illustration below for your first
and second cut)
S Your first cut should extend 1/3 of the
diameter of the log.
TYPES OF CUTTING USED FOR
S Finish with your second cut.
BUCKING
WARNING: If saw becomes pinched or
hung in a log, don’t try to force it out. You
can lose control of the saw resulting in injury
and/or damage to the saw. Stop the saw,
drive a wedge of plastic or wood into the cut
until the saw can be removed easily. Restart
the saw and carefully reenter the cut. To
avoid kickback and chain damage, do not
use a metal wedge. Do not attempt to re-
start saw when it is pinched or hung in alog.
Using a log
for support
nd
2
Cut
st
1
Cut
Cut
Overcutting
Undercutting
st
Using a log
for support
1
Overcutting begins on the top side of the
log with the bottom of the saw against the
log. When overcutting use light downward
pressure.
Undercutting involves cutting on the un-
derside of the log with top of saw against the
log. When undercutting use light upward
pressure. Hold saw firmly and maintain
control. The saw will tend to push back to-
ward you.
nd
2
Cut
nd
Using a
2
Cut
support stand
st
WARNING: Never turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
1
Cut
Using a
st
BUCKING WITHOUT A
1
Cut
support stand
SUPPORT
S Overcut through 1/3 of the diameter of the
nd
log.
2
Cut
S Roll the log over and finish with a second
overcut.
S Watch for logs with a pressure side. See
illustration for cutting logs with a pressure
side.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S Finish with an overcut.
REMOVING A PINCHED SAW
S Always use an overcut to cut small and
freely hanging limbs. Undercutting could
cause limbs to fall and pinch the saw.
(A SAW HUNG IN THE LOG)
S If saw becomes pinched or hung in a log,
don’t try to force it out. You can lose con-
trol of the saw resulting in personal injury
and/or damage to the saw. Stop the saw
and drive plastic or wooden wedge into
the cut until saw can be removed easily.
S Restart the saw and carefully reenter the
cut. To avoid kickback and chain dam-
age, do not use a metal wedge. Do not at-
tempt to restart your saw when it is
pinched or hung in a log.
PRUNING
WARNING: Be alert for and guard
against kickback. Do not allow the moving
chain to contact any other branches or ob-
jects at the nose of the guide bar when limb-
ing or pruning. Allowing such contact can
result in serious injury.
S Limit pruning to limbs shoulder height or
below. Do not cut if branches are higher
than your shoulder. Get a professional to
do the job.
Use a wedge
to remove
S See illustration for the pruning
technique.
pinched sa
S Make your fist cut 1/3 of the way
through the bottom of the limb.
S Next make a 2nd cut all the way
through the limb. Then cut a third
overcut leaving a 1 to 2 inch collar
from the truck of the tree.
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
LIMBING AND PRUNING
Second cut
Third cut
WARNING: Never climb into a tree to
limb or prune. Do not stand on ladders, plat-
forms, a log, or in any position which can
cause you to lose your balance or control of
the saw.
IMPORTANT POINTS
S Work slowly, keeping both hands firmly
gripped on the saw. Maintain secure foot-
ing and balance.
Collar
First cut
S Watch out for springpoles. Use extreme
caution when cutting small limbs. Slender
material may catch saw chain and be
whipped toward you or pull you off bal-
ance.
Pruning technique
SERVICE
S Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or saw
when tension in wood fibers is released.
S Keep a clear work area. Frequently clear
branches out of the way to avoid tripping
over them.
We recommend all service and adjustments
not listed in this manual be performed by an
authorized or Master Service Dealer.
MAINTENANCE SCHEDULE
Check:
LIMBING
Fuel Mixture Level. . Before each use
Bar Lubrication . . . . Before each use
Chain Tension . . . . . Before each use
Chain Sharpness . . Before each use
For damaged parts . Before each use
For loose caps. . . . . Before each use
For loose fasteners Before each use
Inspect and Clean:
S Always limb a tree after it is cut down.
Only then can limbing be done safely and
properly.
S Leave the larger limbs underneath the
felled tree to support the tree as you work.
S Start at the base of felled tree and work to-
ward the top, cutting branches and limbs.
Remove small limbs with one cut.
S Keep the tree between you and the chain.
Cut from the side of the tree opposite the
branch you are cutting.
Bar . . . . . . . . . . . . . . Before each use
Complete saw . . . . . After each use
Air filter . . . . . . . . . . . Every 5 hours *
Spark arrestor . . . . . Every 25 hours *
Replace spark plug . Yearly
S Remove larger, supporting branches with
the 1/3, 2/3 cutting techniques described
in the bucking section.
Replace fuel filter . . . Yearly
* Hours of Operation
S Undercut 1/3 of the way through log.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR FILTER
IGNITION TIMING
Ignition timing is fixed and nonadjustable.
CAUTION:Do not clean filter in gasoline or
other flammable solvent to avoid creating a
fire hazard or producing harmful evapora-
tive emissions.
SPARK PLUG
Replace the spark plug yearly.
STORAGE
Cleaning the air filter:
WARNING: Stop engine and allow to
cool, and secure the unit before storing or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
Store unit with all guards in place. Position
so that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
S Clean cover and area around it to keep
dirt and sawdust from falling into carbure-
tor chamber when cover is removed.
S Remove the parts as illustrated below.
S Wash the filter in soap and water.
S
Before storing, drain all fuel from the
unit. Start engine and allow to run until it
stops.
Cylinder
Cover
Screws
Air Filter
S Clean the unit before storing. Pay particu-
lar attention to the air intake area, keeping
it free of debris. Use a mild detergent and
sponge to clean the plastic surfaces.
S Do not store the unit or fuel in a closed
area where fuel vapors can reach sparks
or an open flame from hot water heaters,
electric motors or switches, furnaces, etc.
S Store in a dry area out of the reach of chil-
dren.
Cylinder
Cover
CAUTION: It is important to prevent gum
deposits from forming in essential fuel sys-
tem parts such as the carburetor, fuel filter,
fuel hose, or fuel tank during storage. Alco-
hol blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to fuel mixture separation and
formation of acids during storage. Acidic
gas can damage the engine.
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter
caps. Carburetor adjustment is a compli-
cated task. We recommend that you take
your unit to an Authorized Service Dealer.
Damage will occur if you turn the needles
beyond the limiter stops.
BAR MAINTENANCE
If your saw cuts to one side, has to be forced
through the cut, or has been run with an im-
proper amount of bar lubrication it may be
necessary to service your bar. A worn bar
will damage your chain and make cutting
difficult.
TROUBLESHOOTING
Engine will not start.
Replace your bar if bent or the inside rails of
S Ignition switch off.
the bar are worn.
S Engine flooded.
S Clean the oil holes after each 5 hours of
operation
S Fuel tank empty.
S Spark plug not firing.
S Fuel not reaching carburetor.
Engine will not idle properly.
S Remove sawdust from bar groove period-
ically with a wire or putty knife.
S Carburetor requires adjustment.
Guide Bar
Groove
S Crankshaft seals worn.
Engine will not accelerate, lacks
power, or dies under a load.
S Air filter dirty.
S Spark plug fouled.
Oil Holes
S Carburetor requires adjustment.
Engine smokes excessively.
CHAIN SHARPENING
S Too much oil mixed with gasoline
Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to aprofessional
chain sharpener. If you choose to perform
your own chain sharpening, call our
toll-free helpline and order a free chain
sharpening instruction guide. (See the back
page of this manual for the toll-free phone
number.)
NEED ASSISTANCE?
Need Assistance?
Call 1-800-554-6723.
Need Service Part?
Contact your retailer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
U.S. EPA
LIMITED WARRANTY
EMISSION CONTROL
WARRANTY STATEMENT
ELECTROLUX
HOME
PRODUCTS
NORTH AMERICA, Division of WCI Out-
door Products, Inc., warrants to the origi-
nal purchaser that each new Poulan or Pou-
lan PRO brand gasoline chain saw is free
from defects in material and workmanship
and agrees to repair or replace under this
warranty any defective gasoline chain saw
as follows from the original date of pur-
chase.
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U. S. Environmental
Protection Agency and POULAN/WEED
EATER, DIVISION OF WCI OUTDOOR
PRODUCTS are pleased to explain the
emissions control system warranty on your
lawn and garden equipment engine. All
new utility and lawn and garden equipment
engines must be designed, built, and
equipped to meet the stringent anti---smog
standards. POULAN/WEED EATER must
warrant the emission control system on
your lawn and garden equipment engine
for the periods of time listed below provided
there has been no abuse, neglect, or im-
proper maintenance of your lawn and gar-
den equipment engine. Your emission con-
trol system includes parts such as the
carburetor and the ignition system. Where a
warrantable condition exits, POULAN/
WEED EATER will repair your lawn and gar-
den equipment engine at no cost to you. Ex-
penses covered under warranty include
diagnosis, parts and labor. MANUFAC-
TURER’S WARRANTY COVERAGE: If any
emissions related part on your engine (as
listed under Emissions Control Warranty
Parts List) is defective or a defect in the ma-
terials or workmanship of the engine causes
the failure of such an emission related part,
the part will be repaired or replaced by
POULAN/WEED EATER. OWNER’S WAR-
RANTY RESPONSIBILITIES: As the lawn
and garden equipment engine owner, you
are responsible for the performance of the
required maintenance listed in your Own-
er’s Manual. POULAN/WEED EATER rec-
ommends that you retain all receipts cover-
ing maintenance on your lawn and garden
equipment engine, but POULAN/WEED
EATER cannot deny warranty solely for the
lack of receipts or for your failure to ensure
the performance of all scheduled mainte-
nance. As the lawn and garden equipment
engine owner, you should be aware that
POULAN/WEED EATER may deny you war-
ranty coverage if your lawn and garden
equipment engine or a part of it has failed
due to abuse, neglect, improper mainte-
nance, unapproved modifications, or the
use of parts not made or approved by the
original equipment manufacturer. You are
responsible for presenting your lawn and
garden equipment engine to a POULAN/
WEED EATER authorized repair center as
soon as a problem exists. Warranty repairs
1 Y E A R --- Parts and Labor, when used for
Household purposes.
6 0 D AY S --- Parts and Labor, when used for
Commercial, Professional, or Income Pro-
ducing purposes.
3 0 D AY S --- Parts and Labor, if used for rent-
al purposes.
This warranty is not transferable and does
not cover damage or liability caused by im-
proper handling, improper maintenance, or
the use of accessories and/or attachments
not specifically recommended by ELEC-
TROLUX HOME PRODUCTS NORTH
AMERICA for this chain saw. Additionally,
this warranty does not cover damage
caused by improper handling, improper
maintenance, or if the saw is altered in any
way which in our judgement affects its con-
dition or operation. This warranty does not
cover tune---up, spark plugs, filters, starter
ropes, starter springs, chain sharpening,
bars, chains, and other parts which wear
and require replacement with reasonable
use during the warranty period. This war-
ranty does not cover predelivery set---up,
installation of guide bar and chain, and nor-
mal adjustments explained in the operator’s
manual such as carburetor adjustments
and chain tension adjustments. This war-
ranty does not cover transportation costs.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRESS-
LY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
ELECTROLUX
HOME
PRODUCTS
NORTH AMERICA’S policy is to continu-
should be completed in
a
reasonable
ously improve its products. Therefore,
amount of time, not to exceed 30 days. If
you have any questions regarding your
warranty rights and responsibilities, you
should contact your nearest authorized ser-
vice center or call POULAN/WEED EATER
at 1---800---554---6723. WARRANTY COM-
MENCEMENT DATE: The warranty period
ELECTROLUX
HOME
PRODUCTS
NORTH AMERICA reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obli-
gation to any purchaser.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
begins on the date the lawn and garden
equipment engine is purchased. LENGTH
OF COVERAGE: This warranty shall be for
a period of two years from the initial date of
purchase. WHAT IS COVERED: REPAIR
OR REPLACEMENT OF PARTS. Repair or
replacement of any warranted part will be
performed at no charge to the owner at an
approved POULAN/WEED EATER servic-
ing center. If you have any questions re-
garding your warranty rights and responsi-
bilities, you should contact your nearest
authorized service center or call POULAN/
WEED EATER at 1---800---554---6723 WAR-
RANTY PERIOD: Any warranted part which
is not scheduled for replacement as re-
quired maintenance, or which is scheduled
only for regular inspection to the effect of
“repair or replace as necessary” shall be
warranted for 2 years. Any warranted part
which is scheduled for replacement as re-
quired maintenance shall be warranted for
the period of time up to the first scheduled
part still under warranty. WHAT IS NOT
COVERED: All failures caused by abuse,
neglect, or improper maintenance are not
covered. ADD---ON OR MODIFIED
PARTS: The use of add---on or modified parts
can be grounds for disallowing a warranty
claim. POULAN/WEED EATER is not liable to
cover failures of warranted parts caused by
the use of add---on or modified parts. HOW
TO FILE A CLAIM: If you have any ques-
tions regarding your warranty rights and re-
sponsibilities, you should contact your
nearest authorized service center or call
POULAN/WEED
EATER
at
1---800---554---6723 . WHERE TO GET
WARRANTY SERVICE: Warranty services
or repairs shall be provided at all POULAN/
WEED EATER service centers. call:
1---800---554---6723 MAINTENANCE, RE-
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any POULAN/WEED
EATER approved replacement part used in
the performance of any warranty mainte-
nance or repair on emission related parts
will be provided without charge to the owner
if the part is under warranty. EMISSION
CONTROL WARRANTY PARTS LIST: Car-
buretor, Ignition System: Spark Plug (cov-
ered up to maintenance schedule), Ignition
Module. MAINTENANCE STATEMENT:
The owner is responsible for the perfor-
mance of all required maintenance as de-
fined in the owner’s manual.
replacement
point
for
that
part.
DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
the determination that a warranted part is
defective if the diagnostic work is performed
at an approved POULAN/WEED EATER
servicing center. CONSEQUENTIAL DAM-
AGES: POULAN/WEED EATER may be li-
able for damages to other engine compo-
nents caused by the failure of a warranted
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|