901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 1
ESPAÑOL: PÁGINA 13
FRANÇAISE : PAGE 25
Instruction
manual
Double Insulated
Portable Electric Drills
MODEL 2620
3/8" Drill
MODEL 6614
1/2" Drill
MODEL 2621
3/8" Keyless Drill
MODEL 6615
1/2" Keyless Drill
IMPORTANT
To learn more about Porter-Cable
visit our website at:
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Part No. 901013 - 12-31-01
Copyright © 2001 PORTER-CABLE Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 3
9. USE SAFETY GLASSES. Wear safety glasses or goggles while operating
power tools. Also face or dust mask if operation creates dust. All persons in
the area where power tools are being operated should also wear safety
glasses and face or dust mask.
10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect
from receptacle. Keep cord from heat, oil, and sharp edges. Have damaged
or worn power cord and strain reliever replaced immediately. DO NOT
ATTEMPT TO REPAIR POWER CORD.
11. SECURE WORK. Use clamps or a vise to hold work. It’s safer than using
your hand and it frees both hands to operate tool.
12. DON’T OVERREACH. Keep proper footing and balance at all times.
13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better
and safer performance. Follow instructions for lubricating and changing
accessories. Inspect tool cords periodically and if damaged, have repaired by
authorized service facility. Inspect extension cords periodically and replace if
damaged. Have all worn, broken or lost parts replaced immediately. Keep
handles dry, clean and free from oil and grease.
14. DISCONNECT TOOLS when not in use, before servicing, and when
changing accessories such as blades, bits, cutters, etc.
15. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking
to see that keys and adjusting wrenches are removed from the tool before
turning it on.
16. AVOID UNINTENTIONAL STARTING. Do not carry a plugged-in tool with
finger on switch. Be sure switch is off when plugging in. Keep hands, body and
clothing clear of blades, bits, cutters, etc. when plugging in the tool.
17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use
only extension cords marked with the suffix W-A or W “Suitable for use with
outdoor appliances – store indoors when not in use.”
18. STAY ALERT. Watch what you are doing. Use common sense. Do not
operate tool when you are tired or while under the influence of medication,
alcohol or drugs.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to determine that it
will operate properly and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service
center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use tool if
switch does not turn it on and off.
20. WEAR EAR PROTECTION to safeguard against possible hearing loss.
SAVE THESE INSTRUCTIONS
ADDITIONAL SAFETY RULES FOR PORTABLE DRILLS
1. ALWAYS hold drill by the handle(s) ONLY to prevent accidental electrical
shock resulting from cutting a live wire when drilling into a wall or other blind
areas.
2. DO NOT use bits larger than those recommended. They increase the
chance of jamming. Large bits may also overload the drill and damage the
motor and gears.
3. USE ONLY the proper chuck key to tighten or loosen the chuck. Do not
use chuck if jaws or other parts are cracked or worn.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 4
4. VERIFY the drill’s rotation before starting the drill so it is correct for the
operation being performed.
5. NEVER change direction or rotation of reversing model until motor has
completely stopped.
6. NEVER hold work in your hand, lap, or against other parts of your body
when drilling.
7. DO NOT use drill as a router or try to elongate or enlarge holes by twisting
the drill. Drill bits may break and cause injury.
8. APPLY FORWARD FORCE on the pistol grip handle ONLY, and ONLY
with your hands. Models with auxiliary handle: grasp auxiliary handle with one
hand to resist rotational force.
9. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC.
Take extra care to prevent inhalation and skin contact when working with
these materials. Request, and follow, any safety information available from
your material supplier.
REPLACEMENT PARTS
When servicing use only identical replacement parts.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown on
the specification plate on the tool. Several models, however, are designed for
A.C. current only. Refer to the specification plate on your tool for proper
voltage and current rating.
CAUTION: Do not operate your tool on a current on which the voltage
is not within correct limits. Do not operate tools rated A.C. only on
D.C. current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found in
this section. This table is based on limiting line voltage drop to 5 volts (10 volts
for 230 volts) at 150% of rated amperes.
If an extension cord is to be used outdoors it must be marked with the suffix
W-A or W following the cord type designation. For example – SJTW-A to
indicate it is acceptable for outdoor use.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
Length of Cord in Feet
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 5
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable drills are designed to drill holes of various sizes in wood and
metal as indicated in the following chart:
Model # of Drill
2620
Type of Bit
Twist Drill
Spade Bit
Self Feed Bit
Twist Drill
Max. Dia. Hole
Material
Steel
Wood
Wood
Steel
3/8"
3/4"
3/8"
1/2"
2621
6614, 6615
Spade Bit
Self Feed Bit
11/2"
11/4"
Wood
Wood
INSTALLING AND REMOVING DRILL BIT
(Except Keyless Models 2621, 6615)
1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE.
2. The three-jaw chuck is designed for self-centering of the drill bit. Open
jaws large enough by turning outer sleeve counterclockwise, when viewing
the chuck from the bit end so that bit shank can be inserted.
3. Clean and insert smooth end of drill bit as far as it will go into the chuck,
then withdraw bit approximately 1/16", or up to the flutes for small bits.
4. While holding the bit with one hand, turn outer sleeve clockwise until bit
is gripped in the chuck.
5. Tighten chuck – insert chuck key into each of 3 keyholes in chuck body
(Fig. 1) in succession and tighten securely by turning key clockwise.
CAUTION: Be sure chuck key is removed before starting tool.
6. To remove bit, reverse foregoing procedure.
LOOSEN
TIGHTEN
Fig. 1
INSTALLING AND REMOVING DRILL BIT
(Keyless Models 2621, 6615)
1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE.
2. The three-jaw chuck is designed for self-centering of the bit. Open jaws
large enough by turning outer sleeve (A) Fig. 2, counterclockwise, when
viewing the chuck from the bit end, so that bit shank can be inserted easily.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 6
B
A
Fig. 2
3. Clean and insert smooth end of bit as far as it will go into the chuck, then
withdraw bit approximately 1/16", or up to the flutes for small bits.
4. While holding the bit with one hand, turn outer sleeve (A) Fig. 2, clockwise
until the bit is gripped in the chuck.
5. Tighten chuck by holding chuck ring (B) Fig. 2, with one hand while
turning outer sleeve (A) clockwise with other hand. Tighten securely.
WARNING: Do not operate drill motor while installing or removing
bits. Operating drill motor can cause bit to be thrown from chuck
causing personal injury.
6. To remove bit, reverse foregoing procedure.
TO INSTALL AUXILIARY HANDLE
An auxiliary handle is supplied with some models. This handle screws directly
into the drill housing providing complete control of the drill.
It is strongly recommended that the auxiliary handle be used and tool held as
illustrated in Fig. 4 during all drilling operations.
TO START AND STOP DRILL
1. Make sure drill switch is “OFF”. Make sure power circuit voltage is the
same as that shown on the specification plate of the drill. Connect drill to
power circuit.
2. Squeeze TRIGGER SWITCH (Fig. 3) to start motor. Release trigger to stop
motor.
3. LOCK BUTTON – A lock button (Fig. 3) is provided to keep motor running
without holding the trigger switch ON.
TO LOCK the trigger switch ON, squeeze the trigger as far as it will go, push
in lock button and release trigger.
TO UNLOCK lock button, squeeze trigger and release, leaving lock button free
to spring out.
NOTE: The lock button can be engaged only when the drill is running
at maximum speed.
CAUTION: NEVER USE THE LOCK BUTTON WHERE DRILL MAY
HAVE TO BE STOPPED SUDDENLY.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 7
REVERSING
SWITCH
LOCK
BUTTON
TRIGGER
SWITCH
Fig. 3
4. REVERSING SWITCH – The reversing switch is located as indicated in
Fig. 3. These models will operate in either the forward direction (clockwise
rotation) for drilling holes, or the reverse direction (counterclockwise rotation)
for releasing jammed drill bits. For counterclockwise rotation, stop the motor
by releasing the trigger switch and push the reversing switch toward the right
side of the drill, or in the opposite direction for clockwise rotation.
NOTE: Never attempt to change direction of rotation while switch is
ON. To do so, may damage interlock feature built into switch. Be sure
switch is OFF and motor has completely stopped before changing
direction of rotation.
5. VARIABLE SPEED – As the trigger switch is squeezed, the drill speed
Increases.
HOW TO HOLD THE DRILL
WARNING: The front end of drill may be made live if the tool drills into
live wiring in a wall. TO PREVENT ACCIDENTAL ELECTRICAL
SHOCK, DRILL MUST BE HELD AS SHOWN IN FIG. 4. APPLY
FORWARD FORCE ON THE PISTOL GRIP HANDLE ONLY, AND
ONLY WITH YOUR HANDS.
An auxiliary handle is supplied with some models. The auxiliary handle should
be used on those models during all drilling operations: grasp auxiliary handle
with one hand to resist rotational force ONLY.
MODELS 6614, 6615
MODELS 2620, 2621
Fig. 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 8
HOW TO USE THE DRILL
GENERAL DRILLING
1. Be sure drill bit is securely gripped in chuck. (See INSTALLING AND
REMOVING DRILL BIT).
2. Set REVERSING SWITCH for clockwise rotation.
3. Make sure work is held securely in vise or clamped in place prior to
starting drilling operation.
CAUTION: Loose work may spin and cause bodily injury.
4. Locate exact center for hole to be drilled and using a center punch, make
a small dent in work.
5. Place tip of drill bit in dent made by center punch, hold drill square with
work, and start the motor.
Apply steady, even pressure to keep drill bit cutting. Too little pressure will
keep the bit from cutting and dull the edges due to excessive friction created
by sliding over the surface.
CAUTION: Too much pressure may cause the bit to break or
overheat resulting in bodily injury or damaged drill bits.
CAUTION: BE ALERT and brace yourself against the twisting action
of the drill, should the bit jam in the work.
6. If drill stalls or becomes jammed in the hole, release trigger immediately,
removing drill bit from work and determine cause of stalling or jamming. DO
NOT SQUEEZE TRIGGER ON AND OFF IN AN ATTEMPT TO FREE A
STALLED OR JAMMED DRILL – THIS WILL DAMAGE THE MOTOR. The
direction of rotation may be reversed to help free a jammed bit. Be sure
direction of rotation is RESET before attempting to continue drilling.
7. Reduce the pressure on the drill just before the bit cuts through the work
to avoid splintering wood or stalling in metal.
8. When bit has completely penetrated work and is spinning freely, withdraw
it from the work while the motor is still running, then turn off drill.
DRILLING WOOD
In addition to the instructions listed under GENERAL DRlLLlNG, the following
also apply:
1. When using twist drills in wood, they should be withdrawn from the hole
frequently to clear chips built up in flutes to avoid overheating and burning
work.
2. If a backing block is used to keep back of work from splintering, it should
be clamped securely in place. If a backing block is not used with spade bits
or auger bits, ease up pressure as soon as bit point breaks through work, and
complete the hole from the opposite side.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 9
DRILLING METAL
In addition to the instructions listed under GENERAL DRILLING, the following
also apply:
CAUTION: When drilling metal, jamming of bit is more likely than
when drilling other materials.
1. Use only good quality sharp high speed steel twist bits when drilling
metal.
2. Start drilling with slow speed and gradually increase speed as drill cuts.
The harder the material, the slower the speed required. The softer the material,
the faster the speed.
3. When drilling a large hole, it is easier to first drill a smaller hole and then
enlarge it to the required size.
4. The use of a lubricant, such as oil, on the drill point helps keep the bit
cool, increases drilling action and prolongs drill bit life.
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. Remove
buildup of grime resulting from working with green or sappy wood. All plastic
parts should be cleaned with a soft damp cloth. NEVER use solvents to clean
plastic parts. They could possibly dissolve or otherwise damage the material.
CAUTION: Wear safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug
are making good contact in the outlet. Also, check for blown fuses or open
circuit breakers in the line.
CHUCK REPLACEMENT
1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE.
2. Open chuck jaws as wide as possible to gain access to the chuck
retaining screw.
3. Remove chuck retaining screw with a standard “flat” screwdriver. Turn
screw clockwise (left hand threads) to remove.
4. Place the short end of a large allen wrench (1/4" or larger) into the chuck.
Align wrench flats with chuck jaws and tighten chuck securely using chuck
key. While supporting chuck on a solid surface, position allen wrench to left
(see Fig. 5) and strike wrench a sharp blow with a hammer to loosen chuck.
Turn chuck counterclockwise to remove.
NOTE: Some Models have a washer behind the chuck. The washer
should remain on the spindle for use with the replacement chuck.
5. INSTALL CHUCK: Open jaws of replacement chuck as wide as possible.
Thread chuck onto spindle by turning chuck clockwise. Hand tighten. Install
allen wrench in chuck (see Step 4). While supporting chuck on a solid surface,
position allen wrench to the right (see Fig. 6) and strike a sharp blow with a
hammer to seat chuck onto spindle.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 10
REMOVE CHUCK
HAMMER
INSTALL CHUCK
HAMMER
ALLEN
WRENCH
ALLEN
WRENCH
SUPPORT
SUPPORT
Fig. 6
Fig. 5
6. Remove allen wrench from chuck.
7. INSTALL CHUCK RETAINING SCREW: Turn screw counterclockwise with
a “flat” screwdriver. Tighten securely.
BRUSH INSPECTION AND LUBRICATION
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY
SERVICE CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected. Have worn parts replaced and lubricate with fresh lubricant. Have
new brushes installed, and test the tool for performance.
Any loss of power before the above maintenance check may indicate the need
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL
UNDER THIS CONDITION. If proper operating voltage is present, return your
tool to the service station for immediate service.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to
wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY
SERVICE CENTER. All repairs made by these agencies are fully guaranteed
against defective material and workmanship. We cannot guarantee repairs
made or attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 11
ACCESSORIES
A complete line of accessories is available from your Porter-Cable •
Delta Supplier, Porter-Cable • Delta Factory Service Centers, and
Porter-Cable Authorized Service Stations. Please visit our Web Site
www.porter-cable.com for a catalog or for the name of your nearest
supplier.
WARNING: Since accessories other than those offered by Porter-
Cable • Delta have not been tested with this product, use of such
accessories could be hazardous. For safest operation, only Porter-
Cable • Delta recommended accessories should be used with this
product.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 12
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from
state to state.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
901013 - 12-31-01.qxd 2/11/02 3:01 PM Page 40
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
ARIZONA
ILLINOIS
MINNESOTA
Cleveland 44125
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Addison 60101 (Chicago)
311 Laura Drive
Phone: (630) 628-6100
Fax: (630) 628-0023
Minneapolis 55429
8001 Sweet Valley Drive Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
OREGON
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MISSOURI
Portland 97230
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: (816) 221-2070
Fax: (816) 221-2897
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
MARYLAND
PENNSYLVANIA
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
TEXAS
FLORIDA
NEW YORK
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
Houston 77055
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
MICHIGAN
WASHINGTON
GEORGIA
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
OHIO
Auburn 98001 (Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Forest Park 30297 (Atlanta)
5442 Frontage Road, Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts
and accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized
Service Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will
be directed to the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en
muchas grandes ciudades. Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los
accesorios para los productos Porter-Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable
Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas
opciones, llame al 888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service
agréés sont situés dans beaucoup de grandes villes. Appelez au 800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en
repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-Cable Delta, s’adresser à tout distributeur Porter-Cable
Delta, centre de service agréé ou centre de service d’usine Porter-Cable Delta. Si vous n’avez accès à aucun de ces centres, appeler
le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable Delta le plus proche.
•
•
•
•
•
•
•
•
•
•
•
•
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 836-2840
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): BAMMER®, LASERLOC®, OMNIJIG®, POCKET CUTTER®,
PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®, QUICKSAND®, SANDTRAP®, SAW BOSS®, SPEED-BLOC®, SPEEDMATIC®,
SPEEDTRONIC®, STAIR-EASE®, THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER SAW®, TORQ-BUSTER®,
VERSA-PLANE®, WHISPER SERIES®, DURATRONIC™, FRAME SAW™, INNOVATION THAT WORKS™, JETSTREAM™, MICRO-SET™,
MORTEN™, NETWORK™, RIPTIDE™, TRU-MATCH™, WOODWORKER’S CHOICE™, THE AMERICAN WOOD SHOP™ (design) , AUTO-
SET™, B.O.S.S.™, BUILDER’S SAW™, CONTRACTOR’S SAW™, DELTA™, DELTACRAFT™, HOMECRAFT™, JET-LOCK™, KICKSTAND™,
THE LUMBER COMPANY™ (design). MICRO-SET™, Q3™, QUICKSET II™, QUICKSET PLUS™, SAFEGUARD II™, SANDING CENTER™,
SIDEKICK™, UNIFENCE™, UNIGUARD™, UNIRIP™, UNISAW™, VERSA-FEEDER™ , TPS™, Emc²™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|