SpectraLink 6100 MCU
Installation and Operation
SpectraLink 6000 System
November 2009 Edition
1725-36097-001
Version J
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
This document explains installation and operation of Polycom’s
SpectraLink 6000 System, using the SpectraLink 6100 Master Control
Unit (MCU). The SpectraLink 6100 MCU adds wireless service to your
existing telephone system. The installation process connects the
SpectraLink 6000 System to your telephone system, and activates the
SpectraLink 6000 Wireless Telephones.
Polycom Model Numbers
This document covers the following registered model numbers:
SCA416, SCA408, SCA516, SCC408, SCC416, SCD408, SCD416,
SCE408, SCE416, SCF4089, SCF416, SCI408, SCI416, SCJ408, SCJ416,
SCK408, SCK416, SCL408, SCL416, SCM408, SCM416, SCN408,
SCN416, SCO408, SCO416, SCS416, SCT416, SCX416 RCC400,
RCO400, RCU100, RCU200, RCU201, MOG400
Related Documents
SpectraLink 6100 MCU: Facility Preparation (1725-36096-001)
SpectraLink 6100 MCU: Quick Reference (1725-36098-001)
SpectraLink 6100 MCU: Open Application Interface (OAI) Gateway
Installation and Operation (1725-36120-001)
SpectraLink 6020 Wireless Telephone Configuration and Administration
Using HAT (1725-36094-001)
Installing the Outdoor Base Station (1725-36127-001)
Available at
PN: 1725-36097-001_J.doc
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
LinkPlus Interface Guide (1725-361xx-001 where xx indicates a number
corresponding to the type of PBX)
Available at
Customer Support
Polycom wants you to have a successful installation. If you have
questions please contact the Customer Support Hotline at
(800) 775-5330. The hotline is open Monday through Friday,
6 a.m. to 6 p.m. Mountain time.
For Technical Support: [email protected]
For Knowledge Base:
For Return Material Authorization: [email protected]
Icons and Conventions
This manual uses the following icons and conventions.
Caution! Follow these instructions carefully to avoid danger.
Note these instructions carefully.
Label
This typeface indicates a key, label, or button on SpectraLink
hardware.
4
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Pull Cable ...........................................................................................18
PN: 1725-36097-001_J.doc
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Install MCUs......................................................................................31
Test Handsets ....................................................................................44
6
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
12 Safety Notices ........................................................................61
13 Index .....................................................................................63
PN: 1725-36097-001_J.doc
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Installation Overview
Installation has three phases. In most cases, a separate person is
responsible for each phase.
1. Site preparation and wire installation: This is usually done by a
wire technician or contractor.
2. Installing the SpectraLink system: This is done by Polycom or one
of our certified distributors.
3. Programming the customer’s telephone system to work with the
SpectraLink system: This is usually done by the customer’s system
administrator or technician.
Because these major steps require some parallel activities, it is
important to coordinate the activities among the persons involved.
This table lists the installation steps and the person usually
responsible for each step.
PN: 1725-36097-001_J.doc
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Installation Steps and Responsibilities
Task
Description
Wire Contractor
or Electrician
Field Service
Engineer
Customer Project
Mgr/ System Admin
9
Site Preparation
9
Determine location of MCU
Run Cable for System
9
Run cable to Base Station
locations
9
9
Pull cable
Terminate cable at Base Station
locations
9
9
Prepare and install demarc blocks
Assign and program ports
9
Connect cables to demarc blocks
Install SpectraLink System
Survey site and check
components
9
Install MCUs
9
9
Install Base Stations
Install outdoor Base Stations
Connect and register handsets
Set up diagnostic modem
Register handsets
9
9
9
9
9
Program handset features
Test handsets
9
9
Site certification
10
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
2
SpectraLink 6000 System
Overview
Review this section if you are unfamiliar with the features and
operation of the SpectraLink 6000 System.
System Operation
The SpectraLink 6000 System is a wireless communication system that
offers direct telephone access for incoming and outgoing calls
anywhere within a facility.
The SpectraLink 6000 System consists of three basic components: the
Master Control Unit, the Base Station and SpectraLink 6000 Wireless
Telephones, or handsets. This diagram shows an overview of the
system. Components are described below.
The SpectraLink 6000 System
PN: 1725-36097-001_J.doc
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Master Control Unit (MCU)
Serves as the connecting point, or gateway, between the Base Stations
and the existing telephone system. One or more of these boxes
(approximately 12” x 3” x 7”) are typically installed in the telephone
equipment room and provide connectivity from the telephone system
to the SpectraLink 6000 System. Each MCU is hard-wired to one or
more Base Stations, which in turn provides the wireless link to each of
the SpectraLink 6000 Wireless Telephones. The MCU establishes the
connection from the telephone line to the appropriate Base Station in
order to reach a handset.
The MCU supports four Base Stations and up to 16 handsets. Up to
four SpectraLink 6100 MCUs can be linked together for extended
coverage area. Chained MCUs support up to 64 handsets maximum.
Polycom offers an analog MCU that works with telephone systems
(CO, PBX or Key Systems) with analog (loop start) ports. We also
offer digital MCUs that work with the most common brands of
telephone systems’ (PBX or key systems) digital ports.
Base Stations
Act as a radio transceiver to provide the communications signal
between the handset and the MCU. Base Stations are slightly larger
than a smoke detector and are typically mounted on the ceiling, in
strategic locations throughout the facility. A single Base Station can
provide radio coverage for an area of 5,000 to 50,000 square feet
depending on building obstructions. Base Stations may be located up
to 2,200 cable feet from the MCU.
When a handset user makes or receives a call, the handset and Base
Station establish a digital radio communication link. As the user
moves around the coverage area, calls are “handed off” to the Base
Station that is able to provide the best radio signal (typically the
closest Base Station). These handoffs involve the handset establishing
a communication link with another Base Station and dropping the
previous link.
SpectraLink 6000 Wireless Telephones
Communicate with the Base Station using digital spread spectrum
transmission at 902-928 MHz. Employees can carry handsets to keep
in contact as they move throughout the building. The handsets use
on-premises wireless technology; they are not cellular or satellite
phones. They are connected to the facility’s existing telephone system
12
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6000 System Overview
and, just like wired telephones, can receive calls directly, receive
transferred calls, transfer calls to other extensions, and make outside
and long distance calls (subject to the restrictions applied in your
facility.)
SpectraLink 6100 OAI Gateway
The SpectraLink OAI Gateway and application server are optional
components which enable third-party applications (such as nurse call
systems) to communicate with SpectraLink Wireless Telephones..
See SpectraLink 6100 MCU: Open Application Interface (OAI) Gateway
Installation and Configuration for more information.
System Capacity
Base Station Capacity
Each Base Station supports up to four call paths/simultaneous calls.
Each Base Station can cover 5,000 to 50,000 square feet, depending on
physical layout of location.
Maximum distance from MCU = 2,200 total cable feet.
Individual MCU Capacity
Eight or 16 PBX lines, depending on model.
Each MCU supports up to four Base Stations.
Each MCU supports up to eight simultaneous calls.
Maximum System Capacity
Up to four MCUs may be inter-connected using IPC cables.
64 Wireless Telephones.
16 Base Stations.
32 simultaneous calls.
PN: 1725-36097-001_J.doc
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
The Front Panel of the SpectraLink 6100 MCU
The MCU’s front panel contains the connections to the telephone
system, switches to control system administration, and status LEDs.
1. STEP button: Selects a specific line or Base Station
during registration process.
2. Mode switch: Selects the mode of operation for the
SpectraLink 6100 MCU.
ADMIN: Administration mode, used to set up system
features to match features on the telephone system.
NORMAL: Normal mode, used during day-to-day
operations.
REGISTER: Registration mode, used to add or delete
handsets and Base Stations.
3. DEL/ENTER button: Removes a registered handset from
the system.
4. IPC IN port: Used to connect preceding MCUs in a multi-
MCU configuration.
5. IPC OUT port: Used to connect sequential MCUs in a
multi-MCU configuration or to connect to an Open
Applications Interface (OAI) Telephony Gateway.
6. ERROR LED: Flashes when the system has detected an
error. When flashing, check the STATUS LEDs for an error
code.
7. STATUS LEDs: Indicate system error messages and
status. See SpectraLink 6100 MCU: Installation and
Operation for more information.
8. LINE LEDs: Indicate the line status of each handset:
ringing, in-use or not active.
9. BASE STN LEDs: Indicate the status of each Base
Station.
10. CONN A or B: RJ-21 connector to the cross-connect
demarc block. Connector B is supplied and used only
with four-wire digital interface.
11. PWR jack: Connects to the AC adapter to supply power
to the system.
CAUTION: Use only the provided Class II AC Adapter
with output 24V DC, 1A.
12. Grounding lug: For use on the analog interface MCU
(SCA-5XX).
14
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Site Preparation
Required Materials Provided by Customer
The following equipment must be provided by the customer:
† Outlet Strip Recommended for installations with more than one
MCU. This will allow the MCUs to be turned on and off together.
† Cross-Connect Block Required to connect the telephone switch
ports and the Base Stations to the MCU.
† 25 Pair Cables RJ-21 male at MCU end, required to connect the
MCU to the cross-connect blocks.
† Backboard Space The MCU is designed to be wall mounted to
3/4” plywood securely screwed to the wall.
† Quick Clip Fuse Required with an RCO410 Outdoor Base Station
or when a Base Station is located in a separate building from the
SpectraLink 6100 MCU. Recommended Quick Clip Fuse is
available from Illinois Tool Works, Linx Division, Model # SCP-
2X2.
† Base Station Mounting Hardware If the Base Stations will be
mounted on finished walls or ceilings, a 4 to 5” long 1/4” bolt,
nuts, and washers will be required for each Base Station mounted.
PN: 1725-36097-001_J.doc
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Determine Location of MCU
Each MCU is approximately 2.75” wide, 12.5” high, and 7” deep, and
weighs about 5 pounds. The unit is designed to be wall-mounted over
3/4” plywood.
•
Select a location for the MCU with sufficient backboard space and
an available outlet.
•
•
The MCU must be within 2,200 feet of the Base Stations.
All digital interface modules must be within 250 feet of the
telephone system.
•
•
See your telephone system specifications for distance limitations
for analog modules.
Since the front panel is used for cabling and as an operator’s
console, mount the units so the front panel is accessible.
If your system has more than one MCU, the units should be mounted
vertically, side by side, physically touching the adjacent unit. Do not
stack units on top of one another. Stacked MCUs can cause
overheating and failure.
Polycom recommends an operational temperature range of 0º–
40º C (31º–104º F). Optimal temperature is 20º C (68º F). Humidity
recommendation is 20%– 80% (non-condensing).
16
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Run Cable for System
Run Cables to Base Station Locations
The Base Station locations should be designated on the building floor
plans provided to the Polycom field service engineer. Base Stations
can be mounted easily on raised or acoustical ceiling tiles, or on the
wall. Avoid locating Base Stations in high or hard-to-reach places, as
this will hinder maintenance, testing and/or repositioning.
Wire specifications
The customer’s wire contractor is responsible for adhering to all
local codes for wiring.
Polycom recommends UL-listed wire that conforms to the following
specifications for AWG, distance, and number of power pairs
required for this installation.
Power
Pairs
Max Cable Feet
22 AWG
Max Cable Feet
24 AWG
Max Cable Feet
26 AWG
1
2
3
1,100
2,200
2,200
750
470
940
1,500
2,200
1,400
One additional pair is required for data.
Attenuation must not exceed 6.8 dB/1,000 feet at 772KHz.
Wire that is already installed (spare house cable) can be used when it
is available. House cable will usually run from the MDF in the
telephone equipment room to intermediate distribution frames (IDFs)
spread throughout the facility. Install new wire from the closest IDF
to the Base Station. Be sure no bridge taps, multiples, or “Y”
connections are created or present.
PN: 1725-36097-001_J.doc
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Determine the amount of wire needed to connect the Base Station to
the MCU by scaling from a floor plan or a sketch, pacing, measuring,
or estimating. Remember to include enough wire to reach the ceiling.
The wire length between the MCU and each Base Station may not
exceed 2,200 cable feet.
Install an extra 25 feet of wire at the Base Station to allow for
possible relocation.
Pull Cable
Pull the cable from the MCU location (usually in the telephone
equipment room) to the Base Station locations designated on the floor
plans.
If the cabling exits the building, consult the telephone system
manual, the National Electrical Code (NEC), and local codes for
instructions on providing lightning and other over-current protection.
When cabling an external Base Station or a Base Station with
wiring that exits the building, protect all Base Station wiring with the
Quick Clip Fuse (Illinois Tool Works, Linx Division, SCP-2X2)
before bridging with other Base Station power leads.
Run all cable before attaching the RJ-45 connectors to the Base
Stations. Label both the demarcation block end and the Base Station
end of each wire with the Base Station number using a wire tie marker
or other form of marker.
Remove bridge taps, multiples, or “Y” connections to the Base
Station wires; these will cause data transmission errors.
The area above some suspended ceilings is used as an
environmental air plenum. The NEC requires that wire installed in
plenums be rated for plenum installation.
18
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Run Cable for System
Terminate Cable at Base Station Locations
After running the wire to the Base Station location, terminate the wire
using an RJ-45 modular crimp-on plug. Connect the data pair to pins
1 and 2, and the power pair to pins 7 and 8.
If the connection uses more than two pair, refer to the table on the
following page.
To avoid damage to the connectors or crimps, be sure to run the
wire to the Base Station before connecting the RJ-45 connectors.
RJ-45 Modular Cable
When wiring the 8-pin connector, use the following table as a guide.
8-pin Modular
Connector
MCU Pin
Function
Polarity
1
2
3
4
5
6
7
8
Data 1
Data 2
Any
Any
Power 3
Power 2
Power 2
Power 3
Power 1
Power 1
+
-
+
-
-
+
PN: 1725-36097-001_J.doc
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Prepare Demarc Blocks
The MCU connects to the existing telephone system using RJ-21
connections. An MCU is designed to operate with a specific interface
to the telephone system: two-wire digital or analog, or four-wire
digital. The number of demarcation blocks required for the system
depends on the number and type of MCUs installed.
MCU
Part Number
Wire
Pairs
Interface Type
# Blocks
Analog POTS
SCA-5XX
SCU-5XX
1
1
1
1
Universal Digital Interface (Norstar, Meridian, Comdial, Fujitsu,
Inter-Tel, DEFINITY 2-wire, NEC, Rolm, Toshiba)
Merlin Legend and DEFINITY 4-wire
Mitel (DNIC)
SCF-5XX
SCX-5XX
SCP-5XX
SCB-5XX
2
1
1
2
2
1
1
2
Panasonic (Universal 2-wire Auxiliary Digital)
Executone (Universal 4-wire Auxiliary Digital)
If the wiring between the SpectraLink 6100 MCU and the telephone
system leaves the building, consult your telephone system manual
for instructions on providing adequate lightning and other over-
current protection. All MCUs (except the analog interface SCA-5XX)
are intended only for connection to the isolated side of an on-
premises telephone switch. The interfaces are intended to connect
to digital telephone switch ports that provide signals of 5Vp-p (max)
AC component, and some telephone switches provide a 48 V DC
offset.
Based on the number and type of interfaces in the system, determine
the number of 25-pair cables required to connect line ports and Base
Stations to the demarcation blocks.
The diagrams which follow provide an overview of the connections.
Multiple power pairs
Some sites may prefer to wire Base Stations to a separate demarc
block in order to split out power pairs.
20
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Run Cable for System
Dedicated line for diagnostic modem
The SpectraLink 6100 MCU can be accessed remotely using an
internal modem. To use the modem for remote access, a dedicated
dial-in line must be provided. On digital interface systems this line
must be terminated as a digital extension to the MCU.
Two-wire analog or digital interface
The wiring diagram below shows the connections required for a two-
wire analog or digital interface.
A
Telephone Ports
Pair 1-16
To
PBX
Pair 17 Unused
Pair
18-19
Data Pair
20-23
Pair 24 & 25
Unused
Power Pairs
To
Base Stn. 1-4
Base Stations
Data Pairs
Base Stn. 1-4
Two-wire Analog or Digital Connection
PN: 1725-36097-001_J.doc
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Four-wire digital interface
The wiring diagram below shows the connections required for a four-
wire interface . Each MCU of this type requires two demarcation
blocks which will be wired as indicated.
B
A
Receive (RX)
To PBX
Telephone Ports
Pair 1-16
Pair 17-25 Unused
To
PBX
Transmit (TX)
From PBX
Telephone Ports
Pair 1-16
Pair 17 - Unused
Power Pairs 18-19
Base Stn. 1-4
To
Base Stations
Data Pairs 20-23
Base Stn.1-4
Pair 24 & 25 Unused
Four-wire Digital Connection
22
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Run Cable for System
Install Demarc Blocks
The demarcation blocks used to connect the telephone system and
Base Stations to the MCU should be installed on a typical telephone
facility backboard. A 1/2” or 3/4” thick board mounted on the wall
near the MCU is typical. Although this manual uses 66 blocks as
examples, any standard cross-connect blocks are acceptable.
When cabling an external Base Station or a Base Station with
wiring that exits the building, protect all Base Station wiring with
the Quick Clip Fuse (Illinois Tool Works, Linx Division, SCP-2X2)
before bridging with other Base Station power leads.
If the cabling between the MCU and the telephone system leaves
the building, consult the telephone system manual, the NEC, and
local codes for instructions on providing lightning and other over-
current protection.
Assign and Program Ports
The wire contractor should inform the system administrator which
port numbers have been designated for the handsets and the remote
diagnostics modem line.
The system administrator must assign extension numbers to the
handsets and plan the functions (trunk access, toll restrictions, system
features, ringing options, etc.) to be programmed for the handsets.
This programming will be done after the handsets are registered, but
will be faster if it is planned in advance by verifying the parameters
and features on the current telephone system and wired phones.
For details, refer the system administration document for your PBX.
PN: 1725-36097-001_J.doc
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Connect Cables from Base Stations and Phone
Lines to Demarc Blocks
Two-pair twisted cable from Base Stations installed throughout the
facility converge at the demarc block or backboard. Each MCU can
support four Base Stations and up to 16 handsets. The Base Station
and SpectraLink 6000 Wireless Telephone cables are punched down
onto the demarc/cross-connect blocks as shown in the demarc block
diagrams below. Refer also to the diagrams in Chapter 4, section
Prepare Demarc Blocks and Chapter 5, section Install MCUs.
Photocopy the Handset Planning Worksheet and Base Station Location
Worksheet provided in this manual as needed. Use the forms to track
the Base Stations and handset port assignments connected to each
MCU. As the Polycom field service engineer makes each Base Station
or handset connection, fill in the information on the form to identify
the position of the Base Station or handset (the building and floor
number, for example) and a detailed description of the location
(perhaps a room number). A copy of this form should be posted near
the cross-connect block.
Up to four Base Stations can be connected on a single MCU. Each
Base Station uses two pair, one for data and one for power.
When cabling an external Base Station or a Base Station with
wiring that exits the building, protect all Base Station wiring with
fuse protection. One method is to use a Quick Clip Fuse (Illinois
Tool Works, Linx Division, SCP-2X2) to provide protection from
external wiring.
If the wiring between the MCU and the telephone system leaves
the building, consult the telephone system manual, the NEC, and
local codes for instructions on providing lightning and other over-
current protection.
24
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Run Cable for System
Two-wire analog or digital demarc block
The demarc block for the two-wire analog or digital interface should
be wired as follows.
tip
ring
tip
LINE1
LINE 2
LINE 3
LINE 4
LINE 5
LINE 6
LINE 7
LINE 8
LINE 9
LINE 10
LINE 11
LINE 12
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
25 PAIR MALE
CONNECTOR
CABLE TO
MCU
CONNECTOR A
Telephone
Ports
LINE 13
LINE 14
ring
tip
ring
tip
LINE 15
LINE 16
ring
UNUSED
Base
1 & 2
Station
Power
Pairs
3 & 4
1
2
3
4
Base
Station
Data
Pairs
UNUSED
Two-wire Connector
PN: 1725-36097-001_J.doc
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Four-wire digital demarc block
The four-wire digital interface (future release) requires two demarc
blocks, one to Connector A and one to Connector B on the MCU. They
should be wired as follows.
tip
ring
tip
Line 1 TX
Line 2 TX
Line 3 TX
Line 4 TX
Line 5 TX
Line 6 TX
Line7 TX
Line 8 TX
Line 9 TX
Line 10 TX
Line 11 TX
Line 12 TX
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
25 PAIR MALE
CONNECTOR
CABLE TO
MCU
CONNECTOR A
Telephone
Ports
Note:
TX denotes
data transmitted
from the telephone
system to the
Link150
Line 13 TX
Line 14 TX
ring
tip
ring
tip
Line 15 TX
Line 16 TX
UNUSED
1, & 2
ring
Base
Station
Power
Pairs
3 & 4
1
Base
Station
Data
2
3
4
Pairs
Unused
Four-wire Connector A
26
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Run Cable for System
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
ring
tip
Line 1 RX
Line 2 RX
Line 3 RX
Line 4 RX
Line 5 RX
Line 6 RX
Line 7 RX
Line 8 RX
Line 9 RX
Line 10 RX
Line 11 RX
Line 12 RX
Line 13 RX
Line 14 RX
25 PAIR MALE
CONNECTOR
CABLE TO
MCU
CONNECTOR B
Telephone
Ports
Note:
RX denotes
data received by
the telephone
system from Link 150
ring
tip
ring
tip
ring
tip
Line 15 RX
Line 16 RX
ring
Unused
Pairs
DO NOT
USE
Four-wire Connector B
PN: 1725-36097-001_J.doc
27
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Install SpectraLink 6000 System
Survey Site
Check the site to be sure pre-installation work has been completed
correctly. This includes:
† Location chosen for the MCU is adequate, and power is available.
† Wiring to Base Station locations has been pulled and correctly
terminated.
† Phone lines for the SpectraLink 6000 Wireless Telephones are
installed and properly terminated.
† Dedicated line is available for remote access to diagnostic modem.
† Telephone system administrator is on-site to program the existing
telephone system.
If the work has not been completed, the Polycom field service
engineer can leave the site and reschedule the installation when the
items have been completed or corrected, or assist in preparing the
site.
This unit must be installed by a service person familiar with the
installation of electronic equipment.
Do not power up the unit before it has been properly grounded to a
protective earth. See Grounding instructions below.
P2N8: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Install SpectraLink 6000 System
Check Components
The following items should be at the installation site.
† SpectraLink 6100 Master Control Unit Depending on the size of
your system, there may be up to four MCUs, which will be
chained together to extend the coverage area.
The SpectraLink 6000 System MUST contain only SpectraLink
6100 MCUs. Link 150 Model 2 MCUs or Model 1 MCUs cannot be
used in an M3 system.
† AC Adapter Supplies power to the SpectraLink 6100 MCU.
Use only the provided Class II AC Adapter with output 24V DC, 1A.
† IPC Cable Each MCU is shipped with one inter-processor
communication (IPC) cable to carry signals between SpectraLink
6100 MCU units. It is used only when multiple MCUs are chained
together.
† Base Stations SpectraLink Part Number RCC 400/410 or RCO
400/410 (for outdoor use). Your system may have up to four Base
Stations for each MCU shipped.
† Base Station Mounting Hardware A ceiling clip and plastic bolt
used to attach each Base Station to the T-bar ceiling tile grid.
† MCU Mounting Hardware Four #8 x 3/4” panhead wood screws
and star washers, used to mount the MCU to the wall.
† ESD Bonding Straps To provide static protection for the MCU.
† SpectraLink 6000 Wireless Telephones The correct number of
handsets for this installation.
† Battery Chargers SpectraLink 6000 Wireless Telephones require a
Battery Charging system, usually one per handset.
† Battery Packs The system may have one or more spare Battery
Pack per handset, depending on the needs at your location.
† Documentation and Training Information This includes a user guide
for each handset and the CD which contains all referenced
documents.
PN: 1725-36097-001_J.doc
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
† Grounding materials per section below Grounding Instructions.
30
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Install SpectraLink 6000 System
Install MCUs
Mount MCUs to wall
The MCUs are designed to be mounted on a backboard of 3/4”
plywood, securely fastened to the wall. Mount the MCUs vertically,
side by side, using 2.75” spacing center-to-center for each unit. Do not
stack MCUs on top of one another.
To mount the MCUs:
1. Using a 1/8” drill bit, drill four pilot holes, on 2” x 12.1” centers.
2. If installing only one MCU, insert the #8 x 3/4” screws in the pilot
holes and tighten, leaving a 1/8” to 1/4” gap from the wall.
3. If installing more than one MCU, the ESD bonding strap(s) must
be installed between adjacent units:
4. Remove the screws from the bottom of adjacent units.
5. Place the ESD strap over the pilot holes that span two units, and
hold it against the plywood backboard.
6. Place the star washer on top of the ESD strap.
7. Insert the #8 x 3/4” screw and tighten to leave 1/8” to 1/4” gap
from the wall.
8. Repeat for all ESD straps.
9. Slide the MCU over the screws until it drops in place.
10. Tighten screws fully.
11. Ground the unit per Grounding instructions below.
Grounding instructions
The metal chassis of this unit may contain leakage currents (i.e.,
"touch" current) which is cumulative when multiple units are
connected together to form a system. To prevent the summation of
leakage currents from being present on exposed metal surfaces, the
following installation procedure must be followed.
ꢀ
Safety
Warning
All system units must be grounded to a protective earth by means of
the grounding stud located on the rear panel. Refer to the illustration
below for recommended continuity connection.
PN: 1725-36097-001_J.doc
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
No more than 15 units may be grounded through one connection to
the protective earth ground. Systems involving more than 15 units
must be broken up into groups of 15 or fewer units with each group
provided with an independent protective earthing conductor.
Connect MCU to demarc blocks
Connect the male RJ-21 connector from the appropriate demarcation
block to the designated RJ-21 connector (A or B) on each MCU. Secure
the cables using the keeper.
Connect multi-unit systems
Use the following procedure to connect multiple MCUs.
1. Mount the MCUs side by side.
2. Connect the IPC cable from the OUT port of the first unit to the IN
port of the adjacent unit. Repeat until all units are connected, as
shown in the following illustration.
32
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Install SpectraLink 6000 System
Multi-Unit SpectraLink 6100 MCUs
No IPC cable is connected to the IN port of the first unit. An Open
Applications Interface (OAI) Telephony Gateway may be
connected to the OUT port of the last unit.
When adding a new or replacement MCU to an existing system,
the MCUs will perform a software update. See Chapter 8 section
Replace an MCU for further details.
PN: 1725-36097-001_J.doc
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Connect power
1. Once the units have been properly grounded, connect the power
plug from the AC adapter to the jack labeled PWR on the MCU.
Use only the provided Class II AC Adapter with output 24V DC, 1A.
For installations with more than one MCU, use an outlet strip with a
built-in power switch. This allows the MCUs to be turned on and off
together.
2. Plug the AC adapter into a 110V AC outlet or switch on the outlet
strip to apply power to the MCU.
3. Verify that leakage current ("touch" current) is below 250 μA rms
on exposed metal surfaces.
4. If leakage is excessive, power off the system and re-verify ground
path continuity.
Set switch interface type
The following steps explain how to assign a switch interface type to
the MCU. This procedure must be done on each MCU.
MCUs can be enabled with different/mixed PBX integrations within
the same system and operate normally. However, the MCUs must
be running the same software. See Chapter 8 section Replace an
MCU for details on the software update procedure. If you need
additional help, please contact the Polycom Customer Support for
assistance.
1. Power on the MCU with the mode switch in the NORMAL position.
Because the MCU does not have a switch type assigned, it will
alarm (the ERROR LED will flash along with STATUS LEDs 1, 2, 3, 4,
and 5). This should take less than 2 minutes.
2. Power off the MCU.
3. Move the mode switch to ADMIN and power on the MCU. Within
15 seconds, STATUS LEDs 2 and 4 will light.
4. Press the STEP button three times.
34
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Install SpectraLink 6000 System
STATUS LEDs 1, 2, and 4 must be lit. LINE LEDs 1 through 8
(indicating an unconfigured MCU) should also be lit.
If any other combination of LINE LEDs is lit, then a switch type has
already been selected. Go to step 5 to pick the desired switch type.
5. Press the DEL/ENTER button to select the correct switch interface
type. With each press of the DEL/ENTER button, a different series of
LINE LEDs will be lit. Continue to press DEL/ENTER until the correct
LINE LEDs are lit. Use the following list to select the desired switch
interface.
Switch Interface
Line LEDs
MCU Type
Notes
Analog
1
SCA5xx
The SCA will only support Analog.
Comdial
3
SCU5xx
SCU5xx
SCF5xx
SCB5xx
SCU5xx
SCU5xx
SCU5xx
SCF5xx
SCX5xx
SCU5xx
SCU5xx
SCP5xx
SCU5xx
SCU5xx
DEFINITY – Two-wire
DEFINITY – Four-wire
Executone
Fujitsu
1, 4
1, 5
2, 5
2, 4
2, 3, 4
1, 2
1, 3
1, 2, 3
1, 2, 4
2
Four-wire Interface.
The SCB will only support Executone.
Inter-Tel
Meridian
Merlin Legend
Mitel
Four-wire Interface.
The SCX will only support Mitel.
NEC
Norstar
Panasonic
Siemens / Rolm
Toshiba
5
The SCX will only support Panasonic.
4
2, 3
1 through 8
Unconfigured
6. Move the mode switch back to NORMAL.
7. The MCU will cycle through diagnostic testing. When the system
is ready for use, the ERROR LED should be off, and the LED for the
MCU Number (1 to 4) will be lit. This should take less than two
minutes.
If the LED for the MCU ID does not light, or if an MCU ID is
duplicated, there is most likely a problem with the IPC cabling. If
the system displays an error refer to Chapter 8, section
Troubleshoot Error Codes.
8. If you select a switch type that is not supported by the MCU type,
the system will alarm. The ERROR LED will flash along with STATUS
PN: 1725-36097-001_J.doc
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
LEDs 4 and 5. For example, this alarm will display if you assign
switch type NEC to an SCB-5XX – Executone MCU.
If this alarm displays, use the table above to verify that your MCU
type supports the selected switch type. If you need to change the
switch type, repeat steps 2 through 6.
36
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Install SpectraLink 6000 System
Install Base Stations
Be sure the Base Station is positioned clear of anything that might
damage it. The Base Station should be well above head height, away
from doors and other objects that might strike it, and away from areas
open to the elements or possible water leaks.
Check your location for other radio antenna devices and place the
Base Stations to avoid interference. Leave enough slack wire
(approximately 25 feet) to account for possible future Base Station
moves.
Mount Base Stations on dropped tile ceilings
A ceiling clip and plastic bolt are supplied to install Base Stations on
the drop ceiling rails (T-bars) used to support acoustical tile. The
plastic bolt screws into the top of the Base Station, then snaps into the
ceiling clip which has been attached to the rails that hold the
acoustical tile. The fastener is designed for use on 15/16” wide rails.
1. Attach the metal fastener to the rail (T-bar) supporting the
dropped ceiling by rotating it into position until it snaps into the
locked position.
2. Screw the plastic bolt to the 1/4” x 20 captive nut into the top of
the Base Station.
3. Slide the bolt into the exposed prongs of the metal clip until it
snaps into position.
4. When properly attached, the Base Station should sit almost flush
against the ceiling, and be tightly attached to the clip and T-bar
grid work.
PN: 1725-36097-001_J.doc
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
5. Once the Base Station is anchored to the fastener, lift the acoustical
tile and plug the RJ-45 8-pin modular plug into the connector on
the top of the Base Station.
— The LED will blink red and green as the system software
downloads to the Base Station and the Base Station is tested.
— When the LED blinks amber, the system is ready for operation.
— When the LED blinks green, a telephone has established a
radio link with that Base Station.
— If the LED turns solid red, there should be an error message on
the MCU’s STATUS LEDs. Refer to Chapter 8, section
Troubleshoot Error Codes.
Mount Base Stations on finished ceilings
If your site does not have a dropped tile ceiling, the Base Station can
be mounted to a finished ceiling or wall with a 4 to 5” long 1/4” –20
TPI plastic or nylon screw or bolt (such as a lag screw).
The customer’s wire contractor is responsible for this installation.
1. Drill two holes approximately 1” apart. Make the holes large
enough to accommodate the RJ-45 connector and a bolt to secure
the Base Station.
2. Insert a wide washer above the ceiling, then screw the bolt into
the beam or ceiling.
3. Insert three nuts on the bolt, then screw the Base Station into the
bolt, being careful not to insert the bolt more than 1/3”, five full
turns, into the Base Station.
If the ceiling is open with I-beams or pipe construction, mount the
Base Station with I-beam clamps or pipe clamps.
38
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Install SpectraLink 6000 System
Install Outdoor Base Stations
Outdoor Base Stations are equipped with a protective enclosure,
designed to be mounted to a wall or pole. After the enclosure is
mounted, the Base Station is inserted in the enclosure and connected.
Only RCO Base Stations can be used outdoors.
The customer’s wire contractor is responsible for wiring and
mounting the outdoor Base Station enclosure. The contractor is
responsible for supplying screws, brackets, and other appropriate
hardware.
Wire and connect outdoor Base Stations
If the wiring for a Base Station exits a building—whether to reach
an outdoor Base Station location or to reach a Base Station in
another building—it should be equipped with primary protection
according to the NEC and/or local codes.
Wiring that exits the building must also be fuse protected at both
ends. For example, use a Quick Clip Fuse from Illinois Tool Works,
Linx Division, model number SCP-2X2. Insert the Quick Clip fuses
in place of bridging clips on a 66 block for the non-internal Base
Station circuits.
1. Mount the outdoor Base Station enclosure to a wall or pole. The
enclosure should be attached at the highest point available that
will provide central coverage for the outdoor area.
2. Insert the Base Station cable through the compression fitting and
tighten the fitting.
3. Wire the Base Station connector just as you wired the RJ-45
connectors for the indoor Base Stations.
4. Place the Base Station inside the enclosure with the part number
label facing the back of the enclosure.
5. Screw the protective cover onto the Base Station enclosure.
PN: 1725-36097-001_J.doc
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Connect and Register Handsets
Set Up Diagnostic Modem
Each MCU has an internal modem feature that allows Polycom
technicians to dial into the system for troubleshooting and
maintenance. The modem is enabled on Line 1 when no handset is
registered to Line 1. When enabled, the modem will auto-answer an
incoming call to that line.
This internal modem uses proprietary communication software.
You cannot use commercial software packages to access this
software. If you have a multiple MCU system, you only need to
enable one modem line, on Line 1 of MCU 1. Line 1 positions on
the other MCUs can be used for handsets.
To set up the diagnostic modem:
1. Connect an analog Direct Inward Dial (DID) line to Analog
Interface MCUs (SCA-5XX) or a digital DID line to Digital
Interface MCUs.
2. Move the mode switch to the REGISTER position. The LED for Line
1 should be off, indicating that no handset is registered to Line 1.
If the LED is on then a handset is registered to the line. Refer to
.
3. Dial the number associated with the DID line. After one or two
rings, you should hear the high-pitched modem answer tone.
PN: 1725-36097-001_J.doc
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Register Handsets
Before a handset can be used it must be registered to a line on one of
the MCUs. While handsets are being registered, the system will
continue normal operation.
Use the Handset Planning Worksheet filled out by the system
administrator to be sure you are correctly assigning each handset to
its port and extension number.
All lines are unregistered when shipped from the factory. However, if
you are replacing a failed MCU you may not need to register the
handsets. Refer to Chapter 8 System Administration for details.
Line 1 MCU 1 may be skipped to allow for remote access through
the diagnostic modem.
Each MCU supports eight simultaneous conversations. To
optimize performance and reduce the possibility of call blocking,
distribute the handsets evenly across all MCUs.
To register a handset to your system, do the following:
1. Be sure all unregistered handsets are powered off and that there is
a Base Station plugged in and within range of the handsets to be
registered.
2. Move the mode switch to the REGISTER position. (If your system
has more than one MCU, be sure to move the switch only on the
correct MCU.) The LED which indicates the Box ID (1 through 4)
may change. This is normal and is not an error.
The LINE indicator LEDs now show the registration status of each
line.
— If the LED is on, a handset is registered to the line.
— If the LED is off, no handset is registered to the line.
3. Press the STEP button until the LED for the line to be registered
flashes.
— If the LED is flashing, that line is selected. A flash with the
LED mainly off indicates no handset registered; a flash with
the LED mainly on indicates a handset is registered to the
selected line.
42
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect and Register Handsets
— Initially Line 2 will flash. This is because Line 1 is usually set up
as the remote access diagnostic modem. To register a handset
to Line 1, press the STEP button until Line 1 flashes.
— If the desired line already has a handset registered to it, follow
the procedure outlined below to unregister the handset, then
return to this step.
4. Turn on the handset to be registered by holding down the PWR
key until the handset beeps twice. After a few seconds, the line
indicator LED on the MCU will shine solid red. Once the handset
is registered, the LED for the next line begins to flash.
5. To assign the extension number, hold down the FCN key until
Volume Level displays. Press the # > key until EXTENSION displays
on the handset. Press 0, then enter the correct extension number.
Press END when finished.
6. Repeat steps 3 through 5 for all handsets to be registered.
7. When all handsets are registered, return the mode switch to the
NORMAL position.
Unregister Handsets
If the desired line already has a handset registered to it, follow this
procedure to unregister the handset.
1. Move the mode switch on the MCU to the REGISTER position. If
your system has more than one MCU, be sure to move the switch
on the correct MCU. The LINE indicator LEDs now show which
lines have handsets registered.
2. Use the STEP button to select the line to be unregistered. The LINE
indicator LED for a line that has a handset registered to it will
flash with the LED mainly on.
3. Press the DEL/ENTER button. The LINE indicator LED for the selected
line will be off with a short on flash
4. Register the new handset or return the mode switch to the
NORMAL position.
PN: 1725-36097-001_J.doc
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Program Handset Features
PBX and Key Systems provide users with special features such as
hold, transfer, conference, camp on, and speed dial. These features
can be accessed via the handset, but the telephone system or
SpectraLink 6100 MCU must be programmed to allow access to these
features from the handset. For information on programming the
switch to operate with the handsets, refer to the system
administration document for your PBX.
•
If the SpectraLink 6100 MCU is connected to your telephone
system via analog lines, refer to your analog system’s feature
programming document.
•
If the SpectraLink 6100 MCU is connected to a digital key
telephone system or PBX, refer to your digital system’s feature
programming document.
Test Handsets
Verify proper registration and operation of each handset by
performing the following steps.
1. Press the START key on each handset. The extension number
should clear and you should hear dial tone. On some digital
systems, depending on how the telephone system is programmed,
you may have to select a line to get dial tone.
2. Place a call to each handset to verify ring, answer, clear transmit,
and clear receive audio.
3. Verify all programmed features on each handset.
4. Press the END key. The LINE indicator should turn off.
44
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Site Certification
The Polycom field service engineer should not leave the site before
contacting Polycom to perform remote install verification.
Contact a Polycom engineer on the Customer Support Hotline at
(800) 775-5330. The hours of operation are 6 a.m. to 6 p.m. Mountain
time, Monday through Friday.
The engineer will connect with the diagnostic modem, verify calling
functions, and listen while you perform a walk test. The walk test will
require you to walk the inside perimeter of the coverage area. If all
Base Stations are running, note any areas with heavy static or clarity
problems and report them to a Polycom engineer.
The installation is not complete until these certification steps have
been performed. Do not hand out SpectraLink 6000 Wireless
Telephones at a site that has not been certified.
PN: 1725-36097-001_J.doc
45
Download from Www.Somanuals.com. All Manuals Search And Download.
8
System Administration
Troubleshoot Error Codes
When an alarm is detected, the ERROR LED will light and the MCU’s
STATUS LEDs will display an alarm code.
If the error code refers to a Base Station problem, the Base Stn LED will
indicate which Base Station has the problem. If more than one Base Stn
LED is on, the error code refers to the lowest numbered Base Station
with an error. Use the STEP button to select another Base Station to
display its error code.
For additional assistance in troubleshooting your system, please
contact the Polycom Customer Support Hotline at (800) 775-5330. The
hotline is open Monday through Friday, 6 a.m. to 6 p.m. Mountain
time.
Troubleshoot Handset Features
If handset features are not working properly, disconnect the handset
from the MCU and plug a wired telephone into the port. The
telephone should be the same type as the emulated telephone. Refer
to the appropriate section of the LinkPlus Interface Guide for your PBX
type.
Test the features on the wired telephone.
•
For analog MCUs, verify that feature access codes and switchhook
flash work correctly.
•
For digital MCUs, verify that features are assigned to the correct
keys and are working properly. Refer to the document that covers
button mapping information for the brand of telephone system at
your location.
PN: 1725-36097-001_J.doc
47
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Certain four-wire telephones (such as MERLIN LEGEND) use a
different connector on the phone than on the back of the MCU.
Therefore you may need phone cord or an adapter to perform these
tests.
Status LED Codes
STATUS LEDs
1 2 3 4 5
Description
Action
Random
Cycling
The SpectraLink 6100 MCU is
powering up. Initialization to
follow.
This is not an error and should change to
another code after a minute.
5
SpectraLink 6100 MCU is
initalizing.
Code number will change when finished.
1, 2, 3, or 4
MCU identification number.
Indicates normal operation when it is on steady.
Check the IPC connections.
If the same LED is lit on more
than one MCU:
If the LED is flashing and the
ERROR light is on:
There is a problem with the MCU indicated by
the flashing box ID.
48
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
System Administration
The following STATUS LEDs are displayed in combination with the
ERROR LED.
STATUS LEDs
Description
Action
1, 2, 3, 4, 5
MCU has not been configured for
switch interface type.
Assign a switch type to the MCU. See
Chapter 5, section Install MCUs -Set Switch
Interface Type for instructions.
1, 3
2, 3
A Base Station has reported an
internal problem.
Replace the Base Station. In rare cases a
problem with the MCU can cause this error.
No communication with one or more
Base Stations on this MCU.
Check cabling to verify that the Base
Station’s cable is plugged into and fully
seated in the Base Station port at the back
of the MCU and plugged into the Base
Station at the other end.
If the LED on the Base Station is not lit,
check for proper wiring of the 8-pin modular
plugs. See Chapter 4, section Terminate
Cable at Base Station Locations.
If the cable is over 600 feet long, verify that
the extra wire pairs have been connected
correctly.
If the Base Station LED is flashing red,
check for open or shorts on pins 1 and 2 of
the cable.
If the Base Station has been removed,
acknowledge the alarm by moving the
mode switch to REGISTER. Press the STEP
button until the LED for the removed Base
Station is blinking. Press DEL/ENTER, then
move the mode switch back to NORMAL.
1, 2, 3
4
Internal communication problem with
the MCU.
Replace the MCU.
IPC problem.
Check IPC cabling by disconnecting and
reconnecting the MCUs. Connect the Male
RJ-21 connector from the appropriate
demarcation block to the designated RJ-21
connector (A or B) on each MCU. Secure
cables using the keeper.
If the error still occurs try using a different
IPC cable. Replace MCU if the problem still
occurs.
4, 5
The switch type selected is not
supported by this MCU.
Verify that the switch type selected is
correct. If the type is incorrect, repeat the
steps to select a new switch type. See
Chapter 5 section Install MCUs -Set Switch
Interface Type.
PN: 1725-36097-001_J.doc
49
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
STATUS LEDs
Description
Action
1, 4
The operator is trying to register a
handset or place an admin call on an
MCU with no phone lines.
Return mode switch to the NORMAL
position.
2, 4
3, 4
The MCU was powered on with the
mode switch in the wrong position.
Turn off the MCU, place the mode switch to
the NORMAL position and turn back on.
Configurations on a multi-MCU
installation do not match in each of
the units.
Most likely to occur when an MCU
was just added to the system.
Erase the configuration in the MCU with
incorrect configuration definitions (probably
the MCU that was just added.) To erase the
configuration, refer to Chapter 8, section
Replace an MCU.
Note: Do not erase the configurations in all
the MCUs. In multiple MCU installations the
handset registration information is shared
among the MCUs. This allows you to
replace an MCU without re-registering all
the handsets.
1, 3, 4
REGISTER or ADMIN mode selected on Only one mode switch can be in ADMIN or
more than one MCU at the same
time.
REGISTER at a time. Check the MCUs and
take one of them out of REGISTER or ADMIN
mode.
2, 3, 4
1, 2, 3, 4
1, 5
The MCU was powered on with the
mode switch in the wrong position.
Turn off the unit, place the mode switch to
the NORMAL position and turn back on.
Internal problem with the MCU.
Contact Polycom Customer Service for
technical support.
The MCU was powered on with the
mode switch in the wrong position.
Turn off the MCU, place the mode switch in
the NORMAL position and turn back on..
A possible Base Station failure has
been detected. A Base Station that
had previously been heard by another
Base Station can no longer be heard.
Check to see if the system was powered on
with the switch in the wrong position. If not,
contact Polycom Customer Service.
5
The MCU was powered on with the
mode switch in the wrong position.
Turn off the MCU, place the mode switch in
the NORMAL position and turn back on.
One or more of the Base Stations on
this unit is disabled because it is
located too close to other Base
Stations. The ERROR display refers to
the LED that is red. If more than one
LED is red, it refers to the lowest
numbered Base Station.
Identify which Base Station has been
disabled and move it away from its nearest
neighbor Base Station
Adjust the companding mode from Mu law
to A law. Refer to Chapter 11, section
If Mode switch is in ADMIN mode:
3, 5
The MCUs have incompatible
versions of software.
Contact Polycom Customer Service for
technical support.
50
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
System Administration
Handset Status Indicator Messages
Indicator
Description
Action
BATT
Displays when user is on the handset
and the battery charge is low. The user
has two minutes to complete the call.
Replace the Battery Pack with one
that is charged.
BATTERY LOW
Displays when user is not on the
handset and battery charge is low. The
handset will ring to alert user to this
condition. The handset will not work
until the Battery Pack is replaced.
Replace the Battery Pack with one
that is charged.
INTERNAL ERROR
Communications error between the
handset and the MCU.
Have the user turn the handset off,
then on again. If the error persists
try registering another handset to
this port. If the problem persists,
contact technical support.
NO PBX
There is no telephone system port
connected to the port associated with
this handset, or the telephone system
has not yet synchronized the port.
This message should disappear
when the telephone system ports
are wired and programmed
correctly.
PT UNREGISTERED
The handset is not yet registered to an
MCU.
Register the handset.
PN: 1725-36097-001_J.doc
51
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Replace a Handset
If a handset breaks or needs to be replaced, the old handset must be
deleted and the new handset added.
Delete old handset
1. Make sure all unregistered handsets are off. If this is not done an
unregistered handset may unintentionally register to an available
line.
2. Move the mode switch to the REGISTER position on the MCU.
3. Press the STEP button until the LED for the line to be deleted is
flashing red.
4. Press the DEL/ENTER button.
You can now register a new handset or return the mode switch to the
NORMAL position.
Register new handset
1. Make sure all unregistered handsets are off.
2. Move the mode switch to the REGISTER position.
3. Press the STEP button until the desired line to be registered is
flashing red. Only unregistered lines can be registered.
4. Press PWR on the handset that needs to be registered. The LED
should change to mostly on once the handset is registered.
5. Wait at least three seconds and then press END.
6. Return the mode switch to the NORMAL position.
7. To assign the extension number, hold down the FCN key until
Volume Level displays. Press the # > key until EXTENSION displays
on the handset. Press 0, then enter the correct extension number.
8. When the handset is turned on, the extension will be displayed.
Test the handset by placing a call to each handset to verify that the
correct handset rings.
52
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
System Administration
Replace an MCU
When the system has more than one MCU, each MCU contains a
complete set of configuration information for the entire system. This
includes handset registration information, function definitions, and
frequency sequence selection.
This Configuration Sharing feature allows a failed MCU in a multi-
unit installation to be replaced without having to register the handsets
again.
To replace a failed MCU, first clear the configuration information on
the replacement MCU, then replace the failed MCU.
Clear configuration on replacement MCU
1. Remove power from the replacement MCU. There should be no
IPC cables connected to the IPC ports.
2. Slide the mode switch on the replacement MCU to the ADMIN
position.
3. Apply power.
4. Press the STEP button until the STATUS LEDs light 2, 3, and 4 of the
replacement MCU.
5. Press the DEL/ENTER button.
6. Remove power from the unit.
7. Slide the mode switch to the NORMAL position.
Connect the replacement MCU
1. Remove the failed MCU from the IPC chain
2. Connect the replacement MCU in the position vacated by the
failed MCU.
3. Reconnect the IPC cables for the chain. Double-check that the IN
and OUT ports are correctly connected.
4. Apply power to the MCU.
PN: 1725-36097-001_J.doc
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
MCUs now perform the software updating sequence. The MCU
with the newest revision of the software will update the other
MCUs in the system. It is normal to see status LEDs 1, 3 and 4
blinking to confirm the update. Once the software update starts you
will see cascading/cycling line LEDs on the MCUs. The update
may take only a few minutes or longer, depending on the number
of MCUs installed. Be patient and allow the system to complete
this update. If the software updated does not start after 15 minutes,
reboot the system. If issues still persist, please call Polycom
Customer Support for further assistance.
5. After a few moments each MCU in the chain should have a
unique box ID number (1 through 4), shown on the STATUS LEDs.
If this is not the case, recheck the IPC wiring.
6. If the replacement MCU has STATUS LED 3 and 4 lit, the
configuration data has not been successfully shared. Most likely,
the replacement MCU was powered up before it was correctly
attached to the IPC chain. Repeat the entire replacement
procedure.
Replace a Base Station
To replace a Base Station, unplug the existing Base Station and plug in
the new Base Station.
•
The LED will blink red and green as the system software
downloads to the Base Station and the Base Station is tested.
•
•
When the LED blinks amber, the system is ready for operation.
When the LED blinks green, a handset has established a radio link
with that Base Station.
•
If the LED turns solid red, there should be an error message on the
MCU’s STATUS LEDs and the MCU ERROR LED should be lit.
54
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Handset Planning Worksheet
Copy and complete this worksheet to keep track of the port numbers,
extensions, users, and features assigned to your handsets.
MCU ID: _________
Handset #
Extension
Port ID
User Name
Feature Notes
1 *
2 **
3
4
5
6
7
8
9
10
11
12
13
14
15
16
*On MCU No. 1: Reserve Port 1 for access to SpectraLink
Diagnostic Modem
**On MCU No. 1: Port 2 is used for administrative programming
(analog system only)
PN: 1725-36097-001_J.doc
55
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Base Station Location Worksheet
MCU: ________
Location
Base Station #
Port ID
(e.g.: building, floor #, detailed description)
Base Station 1
Base Station 2
Base Station 3
Base Station 4
1
2
3
4
MCU: ________
Location
Base Station #
Port ID
(e.g.: building, floor #, detailed description)
Base Station 1
Base Station 2
Base Station 3
Base Station 4
1
2
3
4
MCU: ________
Location
Base Station #
Port ID
(e.g.: building, floor #, detailed description)
Base Station 1
Base Station 2
Base Station 3
Base Station 4
1
2
3
4
MCU: ________
Location
Base Station #
Port ID
(e.g.: building, floor #, detailed description)
Base Station 1
Base Station 2
Base Station 3
Base Station 4
1
2
3
4
PN: 1725-36097-001_J.doc
57
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Technical Parameters
Select Alternate Spread Spectrum Sequence
The SpectraLink 6000 System uses spread spectrum radio
transmission. Spread spectrum takes a discrete signal, such as a
digitized voice conversation, and spreads it over a wide range of
frequencies rather than transmitting at a single carrier frequency. The
frequency range may need to be adjusted if other wireless devices in
your facility, such as data terminals or bar code readers, share the
same frequency band.
Units shipped from the factory are preset to operate on sequence 1,
which spans the entire spectrum from 902MHz to 928MHz. If
interference between the SpectraLink 6000 System and other 900MHz
radio devices is anticipated or observed, any one of six alternate
sequences can be selected.
Determine the frequency band of the interfering device, then use the
frequency ranges below (given in MHz) to select the best interference
avoidance pattern for the situation.
Sequence
Frequencies Used by SpectraLink
902-928
1
2
3
4
5
6
7
902-915
902-909 & 921-928
914-928
902-904 & 909-921
904-910 & 920-928
908-922
To change a system to an alternate sequence, perform the following
steps for each MCU.
1. Wait for any calls in progress to end. Power the system off, then
slide the mode switch to the REGISTER position.
PN: 1725-36097-001_J.doc
59
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
2. Power the system on. STATUS LEDs 5 and 1 should be lit,
indicating frequency selection mode. One of the LINE LEDs from 1
to 7 will be indicating the current frequency selected for the MCU.
3. Use the STEP button to select the desired new sequence.
4. Press the DEL/ENTER button. The LED indicates the new frequency
that has been selected.
5. Return the mode switch to the NORMAL position.
6. Repeat steps 1 through 5 for each MCU of a multi-unit
installation.
Change Companding
The factory setting on the SpectraLink 6100 MCU is compatible with
Mu-law companding (signal compression), which is the standard
used by most PBXs in North America. Systems outside North
America generally use A-law companding. If the PBX companding is
incompatible with the MCU’s, the handsets will have distorted or
hissing dial tone, and voice will be unintelligible.
Before you begin, if the system has more than one MCU, erase the
configurations from all MCUs except MCU 1. Refer to Chapter 8,
section Replace an MCU for instructions.
To change the default from Mu- to A-law on the SpectraLink 6100
MCU follow these steps.
1. Power the system off.
2. Slide the mode switch on the first MCU to the ADMIN position.
3. Power the system on. STATUS LEDs 2, 3, and 4 will be solid green.
4. Press the STEP button once. STATUS LEDs 2 and 5 will be lit.
5. If the LED for LINE 1 is lit, the system is set for Mu-law.
If the LED for LINE 2 is lit, the system is set for A-law.
6. Press the DEL/ENTER button to toggle between Mu-law and A-law.
7. When the correct LINE LED is lit, return the mode switch to the
NORMAL position.
60
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Notices
WARNING: Changes or modifications to this equipment not
approved by Polycom may cause this equipment to not comply with
part 15 of the FCC rules and void the user’s authority to operate
this equipment.
WARNING: Polycom products contain no user-serviceable parts
inside. Refer servicing to qualified service personnel.
IMPORTANT SAFETY INFORMATION
Follow these general precautions while installing telephone
equipment:
•
•
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
•
Never touch uninsulated telephone wires or terminals unless
the telephone line has been disconnected at the network
interface.
•
•
Use caution when installing or modifying telephone lines
When installing Base Stations outside or in buildings other than
the one containing the System Controller, take the following
precaution:
If wiring for a Base Station exits a building—whether to reach
an outdoor Base Station location or to reach a Base Station in
another building—the wiring must be protected at both ends by
a Quick Clip Fuse from Illinois Tool Works, Linx Division, model
number SCP-2X2. The Quick Clip Fuse replaces the bridging
clips on the 66 blocks for all four connections to the non-internal
Base Station.
PN: 1725-36097-001_J.doc
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Customer Support Hotline....................................4
A
D
AC Adapter ...........................................................29
A-law......................................................................60
Alternate sequence ...............................................59
Attenuation............................................................17
Demarcation blocks
Four-wire digital ..............................................26
Installing............................................................23
Two-wire analog or digital .............................25
Diagnostic Modem ...............................................21
B
Base Station............................................................28
Cabling ........................................................17, 19
Description........................................................12
Installation ........................................................37
LED ....................................................................47
Location Worksheet.........................................57
Outdoor.............................................................39
Outside Wiring.................................................39
Replacing...........................................................54
Battery Chargers ...................................................29
E
Error Codes............................................................47
ESD bonding strap................................................29
Extension numbers ...............................................52
F
Batteries..................................................................29
Forms
Base Station Location Worksheet...................57
Handset Planning Worksheet ........................55
Frequency, transmission......................................59
C
Cabling
Base Station specifications ..............................17
Base Station, external.......................................23
Base Station, internal .......................................17
Demarcation blocks .........................................23
Exiting the building.........................................18
Four-wire digital ..............................................22
IPC......................................................................35
Prepare Demarc Blocks ...................................20
Quick Clip Fuse................................................15
RJ-45 modular...................................................19
Shipped with system .......................................29
Troubleshooting...............................................48
Two-wire analog or digital .............................21
Ceiling clip.......................................................29, 37
Chargers.................................................................29
Companding..........................................................60
Configuration sharing..........................................53
Connecting MCU to Telephone System.............20
Coverage ................................................................12
G
Grounding .............................................................31
H
Hand-off.................................................................12
Hotline......................................................................4
I
Interface types, Demarc .......................................20
Interference, frequency ........................................59
L
LED
Base Station.......................................................47
Codes .................................................................48
Front Panel........................................................14
Line indicator....................................................14
PN: 1725-36097-001_J.doc
63
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 6100 MCU: Installation and Operation: SpectraLink 6000 System
Troubleshooting...............................................47
Replacing
Base Station.......................................................54
MCU...................................................................53
Wireless Telephone..........................................52
M
Master Control Unit ................................ See MCU
MCU
S
Base Station cabling .........................................18
Connect to Demarc Blocks..............................32
Description........................................................12
Front Panel........................................................14
Location.............................................................16
Mounting...........................................................31
Multiple.............................................................32
Replacing...........................................................53
Mode Switch..........................................................14
Modem .............................................................21, 41
Mounting Hardware ............................................29
Mu-law...................................................................60
Site Certification....................................................45
Site Preparation.....................................................15
Site Survey .............................................................28
SpectraLink 6000 System, Overview..................11
Spread Spectrum Sequence .................................59
STEP Button...........................................................14
Switch type ............................................................34
T
Ports........................................................................20
Troubleshooting....................................................47
P
U
PBX type.................................................................34
Power
Unregister Wireless Telephone...........................43
AC Adapter.............................. See AC Adapter
Outlet strip........................................................15
Power jack.........................................................14
Programming ........................................................23
W
Walk test ................................................................45
Wireless Telephone
Description........................................................13
Planning Worksheet ........................................55
Program.............................................................44
Register..............................................................42
Replacing...........................................................52
Test.....................................................................44
Unregister..........................................................43
Q
Quick Clip Fuse.....................................................15
R
Register Wireless Telephone ...............................42
Remote Access via modem..................................21
64
PN: 1725-36097-001_J.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
|