Planet Technology Network Card IPX 300 Series User Manual

Internet Telephony PBX System  
IPX-300 Series  
Quick Installation Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Document Objectives ....................................................................................... 4  
Document Organization.................................................................................... 5  
Preparation before beginning administration on IP PBX ....................................... 6  
Network Interface quick configurations ......................................................... 7  
Step1. Operation Mode (For IPX-300W)........................................................ 8  
Step2. Internet Setting (AP Mode) ............................................................... 8  
Step3. NAT Setting..................................................................................... 9  
Step4. IPPBX Setup...................................................................................10  
Voice communication samples.....................................................................11  
IP Phone and Wi-Fi Phone register to IP PBX ...............................................12  
IP Phone and Wi-Fi Phone make off-Net calls via Gateway............................15  
Quick reference in CD-ROM guide ....................................................................19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Document Objectives  
This guide provides physical installation, LAN/WAN IP configurations, and Internet  
access  
establishment information for the IP PBX.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Document Organization  
This guide is organized as follows:  
• Preparation before beginning administration on IP PBX  
• Administration interface  
• LAN/WAN Interface quick configurations  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparation before beginning administration on IP PBX  
Physical Installation  
IPX-300: Internet Telephony PBX System  
IPX-300W: Wi-Fi Internet Telephony PBX System  
Figure 1. Front Panel of IPX-300  
Figure 2. Front Panel of IPX-300W  
Figure 3. Rear Panel of IPX-300  
Figure 4. Rear Panel of IPX-300W  
Administration Interface  
IP PBX provides GUI (Web based, Graphical User Interface) for machine  
management and administration.  
Web configuration access:  
To start IP PBX web configuration, you must have one of these web browsers  
installed on computer for management  
• Microsoft Internet Explorer 6.0.0 or higher with Java support  
Default LAN interface IP address of IP PBX is 192.168.0.1. You may now open your  
web browser, and insert 192.168.0.1 in the address bar of your web browser to  
logon IP PBX web configuration page.  
IP PBX will prompt for logon username/password, please enter: admin / 123 to  
continue machine administration.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure5. Input prompt  
In order to connect machine for administration, please locate  
your PC in the same network segment (192.168.0.x) of IP PBX. If  
you’re not familiar with TCP/IP, please refer to related chapter on  
user’s manual CD or consult your network administrator for proper  
network configurations.  
Note  
Network Interface quick configurations  
Wizard for Quick Setup of the IP PBX, after finishing the authentication, please click  
“Wizard” to enter quick start:  
Figure 6. Wizard-Operating Mode settings  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step1. Operation Mode (For IPX-300W)  
For most users, Internet access is the primary application. The IP PBX supports the  
WAN, LAN and WLAN interface for Internet access and remote access. When you  
click “Operation Mode” from within the Wizard Setup, the following setup page will  
be show.  
Three WLAN modes of operation are available for Internet Access:  
AP Mode:  
In this mode the IP PBX supports AP functionality only. The IP PBX has the  
following network interfaces: WAN, LAN and Wireless LAN.  
AP-Client Mode:  
In this mode the IP PBX accesses a remote AP. Please be sure that you have an  
account to access your wireless service provider AP. In this mode the WAN interface  
is used a 2nd LAN interface.  
WISP & AP Mode:  
The IP PBX must access remote AP. Please be sure that have account to access  
from remote AP. In this WISP & AP mode the network interface will change from  
WAN port to LAN port and all of network access will through by remote AP.  
Step2. Internet Setting (AP Mode)  
WAN Setting  
Network Address Translation (NAT) serves connecting multiple  
NAT Mode  
computers to the Internet using one IP address.  
Bridge mode serves to connect a local area network (LAN /  
Bridge Mode  
Wireless) to another local area network that uses the same  
protocol.  
Three methods are available for Internet Access. Static IP  
/ DHCP / PPPoE type for your select. You should refer to  
“Network Setting” in user menu.  
WAN Port IP  
Assignment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 7. Wizard-Internet settings  
AP Setting (For IPX-300W)  
For configuring correctly the WLAN port in client mode, the below instructions will  
provide a quick start. It is advised if possible to use the simplest network settings  
for first try.  
For making sure the IP PBX is connecting to your wireless router (AP). You need  
to set up the following: SSID, Frequency Channel, Authentication method and  
Encryption parameters (Type/Encryption length/Keys.)  
Figure 8. Wizard-AP settings  
Step3. NAT Setting  
LAN IP Setting  
Private IP address for connecting to a local private  
network. (Default: 192.168.0.1)  
LAN IP Address  
Subnet mask for the local private network (Default:  
255.255.255.0)  
Subnet Mask  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DHCP Server  
Enable to open LAN port DHCP server  
Assigned DHCP IP  
Address  
DHCP server range from start IP to end IP  
Client to ask DHCP server refresh time, range from 60  
to 86400 seconds  
DHCP IP Lease Time  
Figure 9. Wizard-NAT settings  
Step4. IPPBX Setup  
The IP PBX allows multiple ITSP providers / User Extensions registration by simply  
fill-in the required information in the provided table.  
Figure 10. Wizard-IP PBX settings  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service Provider:  
Caller ID  
Username  
Password  
Host  
Service provider name  
Input Provider name  
Input Provider password  
Input Providers server address  
Providers server port  
Port  
User Extensions:  
User Extension  
Password  
Input Extension number  
Input Extension password  
Input Extension caller id  
Caller Id  
After completing the wizard setup, click “Submit” button. The IP PBX will save  
configuration and reboot IP PBX automatically, after 50 seconds, you can re-load  
setting page again.  
Figure 11. Wizard-Rebooting  
Voice communication samples  
The chapter shows you the concept and command to help you configure your IP  
PBX System through sample configuration. And provide several ways to make calls  
to desired destination in IP PBX. In this section, we’ll lead you step by step to  
establish your first voice communication via web browsers operations.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IP Phone and Wi-Fi Phone register to IP PBX  
In the following samples, we’ll introduce IP Phone and Wi-Fi Phone register to IP  
PBX applications.  
Figure 12. Topology of instruction example  
Machine configuration:  
STEP 1: Please log in IP PBX via web browser and browse to “Network Setup  
WLAN Setting” configuration menu. Enable the WLAN and setup the related  
configuration. The sample configuration screen is shown below:  
Figure 13. WLAN Setting of IPX-300W  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 2: Browse to “IP PBX Setup User Extensions Setup” configuration menu.  
Figure 14. User extension setting of IP PBX  
STEP 3: Click the “Add” button to create extension account ext.100 and ext.101.  
Figure 15. Add extension setting of IP PBX  
STEP 4: Please log in VIP-154T and browser to “SIP setting Domain Service”  
configuration menu. Insert the account/password information then save and reboot  
machine. The sample configuration screen is shown below:  
Data match with Fi gure 15. IP  
PBX’s extensio n settings  
The IP address  
of IP PBX  
Figure 16. Web page of VIP-154T  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 5: Please take VIP-192 and setup the wireless network to connect with IP  
PBX (IPX-300W) by keypad menu method. Then log in VIP-192 via web browser  
and browser to “SIP Settings” configuration menu. Insert the Register and  
Outbound Proxy IP Address information.  
The IP address  
of IP PBX  
Figure 17. SIP settings of VIP-192  
Then browse to “SIP Account Settings” configuration menu and fill in the account/  
password information. The sample configuration screen is shown below:  
Data match with Fi gure 15. IP  
PBX’s extensio n settings  
Figure 18. SIP account settings of VIP-192  
STEP 6: After both of devices have registered to IP PBX successfully, it could  
browse to “Information PBX Extension Status” page to show the registration  
status:  
Figure 19. Extension status  
Test the scenario:  
1. VIP-154T pick up the telephone  
2. Dial the number: 100 (VIP-192) shall be able to connect to the VIP-192  
1ꢀ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Then the VIP-192 should ring. Please repeat the same dialing steps on VIP-192  
to establish the first voice communication from VIP-154T  
IP Phone and Wi-Fi Phone make off-Net calls via Gateway  
In the following samples, we’ll introduce VIP-154T and VIP-192 makes off-Net Calls  
(PSTN calls) via VIP-480FO applications.  
Figure 20. Installation example with VIP-480FO  
Machine configuration:  
STEP 1: Please refer to the first sample and let VIP-154T and VIP-192 register to  
IP PBX.  
STEP 2: Please log in IP PBX via web browser and browse to “IP PBX Setup User  
Extensions Setup” configuration menu to add four accounts for VIP-480FO using.  
Figure 21. Add accounts for VIP-480FO  
1ꢁ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 3: Browse to “IP PBX Setup Attendant Extension” configuration menu.  
Assign an attendant number which inexistence extension in Extension List and the  
sample configuration screen is shown below:  
Figure 22. Assign an attendant number  
Pressing the “Submit” button for activate the configuration.  
STEP 4: Browse to “IP PBX Setup Dialing Rules” configuration menu. Add a  
dialing rule for making off-Net calls via VIP-480FO, and press the “Insert” button  
for activate the configuration.  
Figure 23. Add dialing rule for grab the FXO ports of VIP-480FO  
STEP 5: Please log in VIP-480FO via web browser and browse to “Advance Set-  
up VoIP Setup VoIP Basic” configuration menu. Insert the account/password  
information and set up the hunting function. The sample configuration screen is  
shown below:  
Figure 24. Set up the number of FXO ports of VIP-480FO  
1ꢂ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 25. Set up the Hunting Member of FXO ports  
Figure 26. Set up the Proxy Server IP address for register to IP PBX  
STEP 6: Browse to “Dialing Plan” configuration menu. Add an Incoming Dial Plan  
(no.0) for redirect the PSTN outgoing calls to FXO ports.  
Figure 27. Add an incoming dial plan  
STEP 7: Browse to “Port Status” configuration menu. Fill in the auto attendant  
number 555 to all of ports. (Where 555 is the autoattendant number of IP PBX)  
Figure 28. Hot Line to auto-attendant of IP PBX  
1ꢃ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP8: After all of devices have registered to IP PBX successfully, the Extension  
Status page will show the registration status:  
Figure 29. Extension status page with Phone and Gateway registered  
Test the scenario:  
1. VIP-154T pick up the telephone  
2. Dial the number: 0 shall be able to connect to the port 1 of VIP-480FO  
3. Then the telephone will hear the dial tone from PSTN lines, and dial the number:  
12345678 shall be able connect to the User A.  
4. Then the telephone of User A will ringing, User A can pick up the handset and  
talk with VIP-154T.  
5. Both VIP-154T and User A hang up the calls.  
6. User A pick up the telephone and dial the number: 23456789 should be able to  
connect to the Auto Attendant System of IP PBX.  
7. The User A will hear the prompts, and dial the extension number: 100 shall be  
able connect to the VIP-192.  
8. Then the VIP-192 should will ringing, and it to pick up the call then talk with  
User A.  
1ꢄ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick reference in CD-ROM guide  
This guide is used to help you startup your Wizard settings. It is also recommended  
to check the user manual CD-ROM for more details likes the “IP PBX Setup, and  
how to set the device back to default value.  
1ꢅ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This page is intentionally left blank  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Microphone LX 20S User Manual
Perle Systems Switch S 1000MM XXXXXX User Manual
Philips MP3 Docking Station DLA77082 79 User Manual
Philips Universal Remote SBC RU 880 User Manual
Phoenix Gold Car Amplifier SD2002 User Manual
Pioneer Car Stereo System DEH 5300UB User Manual
Planet Technology Switch IKVM 1000 User Manual
Poulan Chainsaw 2004 07 User Manual
ProForm Home Gym PFEL51050 User Manual
PYLE Audio Car Stereo System PLD155EL User Manual