WS231
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
PREFACE
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference
that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
Reorient or relocate the receiving antenna.
•
•
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use
the shielded signal cord supplied with this unit.
The Federal Communications Commission warns that changes or
modifications of the unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
CE mark for Class B ITE (Following European standard EN55022/1998;
EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998,
EN60950/1992+A1+A2+A3+A4+A11)
Radio Frequency Interference Statement
Warning:
This is a Class B product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
Canadian Doc Notice
For Class B Computing Devices
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.
“Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de la class B prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada”
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Important Safety Instructions
Please read the following instructions carefully. This manual should be
retained for future use.
1. To clean the LCD Monitor screen, first, make sure the Monitor is in the
power off mode. Unplug the Monitor from its power source before
cleaning it. Do not spray liquid cleaners directly onto the unit. Stand
away from the LCD Monitor and spray cleaning solution onto a rag.
Without applying excessive pressure, clean the screen with the slightly
dampened rag.
2. Do not place your LCD Monitor near a window. Exposing the Monitor to
rain, water, moisture or sunlight can severely damage it.
3. Do not place anything on top of the Monitor-to-PC signal cord. Make sure
the cord is placed in an area where it will not be stepped on.
4. Do not apply pressure to the LCD screen. Excessive pressure may cause
permanent damage to the display.
5. Do not remove the cover or attempt to service this unit by yourself. You
may void the warranty. Servicing of any nature should be performed only
by an authorized technician.
6. Safe storage of the LCD Monitor is in a range of minus 20 to plus 65
degrees Celsius (-4°F-149°F). Storing your LCD Monitor outside this
range could result in permanent damage.
7. If any of the following occurs, immediately unplug your Monitor and call
an authorized technician.
•
•
The power or Monitor-to-PC signal cord is frayed or damaged.
Liquid has been spilled onto the Monitor, or it has been exposed to
rain.
•
The Monitor has been dropped or the case has been damaged.
8. The appliance should be disconnected from the mains by pulling the mains
power cord/mains plug.
9. The socket-outlet shall be installed near the equipment and shall be easily
accessible.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
TABLE OF CONTENTS
PREFACE..................................................................................................................I
TABLE OF CONTENTS....................................................................................... IV
CHAPTER 1..............................................................................................................1
Your new LCD Monitor!........................................................................ 1
Unpacking.............................................................................................. 1
Identifying Components....................................................................... 2
The LCD Monitor — Front View...................................................... 2
The LCD Monitor — Rear View....................................................... 3
Adjusting the Viewing Angle ............................................................... 4
Connecting AC Power.......................................................................... 4
Connecting Video ................................................................................. 5
6Power Management System .............................................................. 6
CHAPTER 2..............................................................................................................7
The LCD Monitor’s Display Controls .................................................. 7
The hotkey descriptions .................................................................... 13
APPENDIX A ..........................................................................................................16
TFT LCD Monitor Specifications ....................................................... 16
APPENDIX B ..........................................................................................................16
APPENDIX C ..........................................................................................................18
Troubleshooting Procedures............................................................. 18
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
The LCD Monitor
Your new LCD Monitor!
Your LCD Monitor has been designed to be versatile, ergonomic and user-friendly.
The LCD Monitor is capable of displaying most standards, from 640 x 480 VGA to
1600 x 1200 UXGA. The digital controls located on the front panel allow the user to
easily adjust the Monitor’s display parameters. The LCD Monitor’s small footprint
allows you more room in your workspace for other peripherals. Lightweight and
compact, the LCD Monitor is the perfect solution for all type of users.
Unpacking
Before you unpack your LCD Monitor, prepare a suitable workspace for your LCD
Monitor and computer. You need a stable, level and clean surface near a wall outlet.
Even though the LCD Monitor uses very little power, you should put it in a location,
which allows sufficient airflow to ensure that the LCD Monitor and your computer
does not become too hot. Set up your LCD Monitor so that the panel doesn’t face a
window where sunlight often comes in. The glare caused by sunlight reflecting off the
LCD Monitor’s screen will make it difficult to see.
After you unpack your LCD Monitor; make sure the following items are included in
the box and in good condition:
•
•
•
•
•
•
•
•
•
LCD Monitor
AC Adapter
Monitor-to-PC Analog signal cable (15-pin)
Monitor-to-PC Digital signal cable (24-pin)
Power cord
This user’s manual
CD Manual
Frequently Asked Questions
Quick Setup Guide
1
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
If you find that any of these items are missing or appear damaged, contact your dealer
immediately. Do not throw away the packing material or shipping carton in case you
need to ship or store the LCD Monitor in the future.
Identifying Components
The LCD Monitor has been designed to provide easy access to all controls and
peripheral ports. The following figures will help you identify the LCD Monitor’s
controls and ports.
The LCD Monitor — Front View
Figure 1-1: The LCD Monitor Panel and Controls
1. LCD Screen
The RGB LCD Monitor Screen is capable of producing most display
standards up to a maximum resolution of 1600 x 1200 (UXGA).
2. Function Control Buttons
These two buttons allow you to select one of the control functions. Press
either the right or left control button to scroll through the menu items. Press
the left function button to activate the OSD Menu.
3. Adjustment Control Buttons
These two buttons allow you to adjust the selected control function to
accommodate your specific working environment. Press the right button to
increase the setting of the selected control function and press the left button to
decrease the setting of the selected control function.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
4. Power Button and Port Select
Push the button to turn the Monitor ON or OFF (push and hold the button for
2 seconds to switch between Analog or Digital input mode).
5. Power-On Indicator
This LED indicator lights when the power is on. The LED indicator will
blink when the LCD Monitor is in Power Saving mode.
The LCD Monitor — Rear View
Figure 1-2: LCD Monitor’s Rear Ports
1. Input signal ports
The monitor has one 15-pin D-sub VGA connector and one 24-pin DVI
connector (optional), the 24-pin DVI connector is for Digital signal if your
PC has a graphic card with DVI connector.
2. USB port (Optional)
Connect the USB cable from this port to PC HOST.
3. DC Power Jack
Connect the AC power Adapter output cable to this connector
3
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Adjusting the Viewing Angle
Your LCD Monitor is designed to allow you to adjust it to a comfortable viewing angle.
Please see Figure 1-3.
Figure 1-3: Angle Settings
Connecting AC Power
Please refer to the following instructions for connecting AC power to the LCD Monitor.
Plug the female end of the power cable into the AC power connector. Plug the male
end of the power cord into a wall socket. The plug on the power cable will vary
according to the electrical standard in your area. Please refer to Figure 1-4.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Figure 1-4: Connecting Power to the LCD Monitor
Connecting Video
1. Turn off your PC and the LCD Monitor before connecting your LCD Monitor
to the computer.
2. Connect one end of the VGA signal cable to the PC’s D-sub VGA port and
the other end to the monitor VGA port. Please refer to Figure 1-5.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Figure 1-5: Connecting the LCD Monitor to the PC
3. If your PC has a graphic card with a 24-pin DVI connector, you may connect
it with the Digital 24-pin DVI signal cable.
4. Make sure the signal cable head is securely connected to the VGA port of
your PC. Tighten the connecting screws to ensure a secure connection.
If both analog (15-pin D-sub VGA) and digital (24-pin DVI) input ports are
connected at the same time, the signal input can be selected with the port
select button. Please go to the next chapter for details.
Power Management System
The LCD Monitor complies with the VESA DPMS (version 1.0p) power management proposal. The
VESA DPMS proposal provides four phases of power saving modes by detecting the horizontal or
vertical sync signal. When the LCD Monitor is in power saving mode or detects an incorrect timing,
the Monitor screen will go blank, and the power LED indicator will start to blink.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
The Display Controls
The LCD Monitor’s Display Controls
The LCD Monitor features an intuitive, menu-driven, On-Screen Display (OSD). You
can access the OSD any time when the PC is powered on. If the PC is in a power
saving mode, or is powered off, the OSD is inaccessible.
The OSD make the adjusting display settings quick and simple. Press the Left
Function button to access the OSD and the Function buttons are used scroll through
the menu items. Use the Adjustment buttons to make changes to the selected menu
item. Please refer to Figure 2-1.
Analog Input Mode (use 15 pin VGA port):
Figure 2-1: The OSD Main Menu
Main Menu Description:
Display Setting parameters including Contrast,
Brightness, Dos Graph/Text, and Auto Adjust.
• DISPLAY
These setting parameters including Scale, Clock, Phase, H-Position,
V-Position.
• GEOMETRIC
• OSD-ADJUST OSD H-Position, OSD V-Position, Language, Information, Reset.
• COLOR
Color temperature for standard CIE 9300°K, 6500°K, or user defined.
• EXIT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
The submenus for each are further described below:
Display Setting sub Menu
Figure 2-2: The Display Setting sub Menu
Description:
Contrast adjustment.
• CONTRAST
Backlight brightness adjustment.
DOS 640x400 or 720x400 mode selection.
To Auto-adjust the geometric parameters.
• BRIGHTNESS
• GRAPH/TEXT
• AUTO ADJUST
• EXIT
Geometric sub Menu
You should only use this menu if the result of the Auto Adjust function is not satisfactory.
Figure 2-3: The Geometric sub Menu
8
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Description:
Full Screen or native display selection.
To adjust the pixel alignment of the display.
To adjust the display for focus and clarity.
Horizontal position adjustment.
• SCALE
• CLOCK
• PHASE
• H-POSITION
• V-POSITION
Vertical position adjustment.
• EXIT
OSD Adjust sub Menu
Figure 2-4: The OSD Adjust sub Menu
Description
• H-POSITION
OSD Horizontal position adjustment.
OSD Vertical position adjustment.
• V-POSITION
• LANGUAGE
• INFORMATION
• RESET
To select different languages of OSD menu.
To get the information of display mode and firmware version.
To set the display parameters to the factory default values.
• EXIT
9
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Color temp. Sub Menu
Figure 2-5: The Color temp. Menu
Description:
• 9300
• 6500
• R
• G
• B
CIE 9300°K color.
CIE 6500°K color.
User color R-Sub contrast adjustment.
User color G-Sub contrast adjustment.
User color B-Sub contrast adjustment.
• EXIT
10
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Digital Input Mode (use 24 pin DVI port):
Figure 2-6: The OSD Main Menu
Main Menu Description:
Display Setting parameters including Contrast,
Brightness, Language, and Scale.
• DISPLAY
OSD H-Position, OSD V-Position, Language, Information, Reset.
• OSD-ADJUST
• EXIT
The submenus for each are further described below:
Display Setting sub Menu
Figure 2-7: The Display Setting sub Menu
11
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Description:
Contrast adjustment.
• CONTRAST
Backlight brightness adjustment.
To select different languages of OSD menu.
Full screen or native display selection.
• BRIGHTNESS
• LANGUAGE
• SCALE
• EXIT
OSD Adjust sub Menu
Figure 2-8: The OSD Adjust sub Menu
Description
OSD Horizontal position adjustment.
• H-POSITION
OSD Vertical position adjustment.
• V-POSITION
• INFORMATION
• RESET
To get the information of display mode and firmware version.
To set the display parameters to the factory default values.
• EXIT
Note:
1. When there is no input signal
When the monitor is ON and there is no Video signal received, the following
message will be displayed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
(Analog mode)
(Digital mode)
Figure 2-9: When there is no input signal
The hotkey descriptions
Figure 2-10: The Hotkeys
1.
2.
3.
4.
Main Menu pop up /Auto-Adjust Hotkey
Press this button to activate the OSD Main
Menu. Press and hold this button for 2
seconds to activate the Auto Adjust
feature.
Figure 2-11
Contrast Adjust Hotkey
Press this button to activate the Contrast
Adjust function, use -/+ adjustment
control buttons to increase or decrease the
display’s contrast.
Figure 2-12
Figure 2-13
Brightness Adjust Hotkey
Press this button to activate the Brightness
Adjust function, use -/+ adjustment
control buttons to increase or decrease
display brightness.
Port Select/Power switch Hotkey
Press and release this button immediately to select either Digital or Analog input mode.
Press and hold this button for 2 seconds to power on or power off the monitor.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDENDUM A
Technical Information
TFT LCD Monitor Specifications
Model
LCD Panel
FMT2315U
23.1” UXGA
Control Functions
Power
Software switch with LED indicator
On-Screen
Display (OSD)
DISPLAY--------------CONTRAST/BRIGHTNESS/AUDIO
VOLUME /GRAPH./TEXT/AUTO
ADJUST
GEOMETRIC--------SCALE/CLOCK/PHASE/H-POSITION
/V-POSITION
OSD ADJUST-------OSD H-POSITION/OSD V-POSITION
/LANGUAGE/INFORMATION /RESET
COLOR---------------USER (9300/6500)/R/G/B
LANGUAGE---------ENGLISH/日本語/DEUTSCH/FRANÇAIS
/NEDERLANDS /SVENSKA
Display Area (mm)
470.4 x 352.8 mm
(23.1 inch diagonal)
Display Colors
Video Interface
16.7M
Analog port: VGA Compatible Analog RGB (15-pin D-Sub)
Separate Sync. /Composite
Digital port: DDWG compliant Single Link Tmds Digital Visual
Interface (DVI)
(with port AUTO-detection)
Scanning
Frequency
H/V, Hz
24-80kHz
50-90
(Analog mode)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
FMT2315U
Scanning Frequency
H/V, Hz
30-80kHz
56-85
(Digital mode)
Power Management
Meets VESA DPMS
Power Consumption
(ON mode/OFF mode)
88W (max.)/5W (max.)
(Measured from AC inlet)
Dimensions WxHxD mm
Net Weight (Kg) Approx.
Power Supply
568 x 570 x 240
15 Kg
12V /6A, 72W
Universal Input AC Adapter (External)
Options
Wall-mounted bracket, Arm-mounted bracket (VESA
Compliance)
USB Hub (1 up and 2 down streams)
Environment
Operating Temperature: 0 to 40° C
Relative Humidity: 10% to 90%
Audio (Two 1 Watt
Yes
speakers with amplifier)
Regulatory
UL/cUL, TÜV-GS, CE, FCC/B, VCCI, FCC B DoC
TÜV-Ergonomics, Energy Star Program
15
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
Supported Timing
Timing for Model FMT2315U (UXGA Resolution)
Dot
Clock
(MHz)
Vertical
Scanning
Frequency
(Hz)
Horizontal
Scanning
Frequency
(kHz)
Sync
Operating
Mode
Polarity or
composite
sync (H/V)
Ite
m
Standards
Resolution
1
2
3
NEC PC98
NEC PC98
MAC 13”
mode
640x400
640x400
640x480
25.20
21.05
30.24
70.15
56.42
66.67
31.50
24.83
35.00
-/-
-/-
-/-
A
A
A/D
4
5
MAC 16”
mode
MAC 17”
mode
832x624
57.28
80.00
74.55
75.02
49.73
60.24
-/-
-/-
A/D
A/D
1024x768
6
7
VGA
VESA
640x350
640x350
25.18
31.50
70.09
85.08
31.47
37.86
+/-
+/-
A/D
A/D
8
9
VGA
VESA
VGA
640x400
640x400
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
800x600
720x400
720x400
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1024x768
25.18
31.50
25.18
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
28.32
35.50
65.00
75.00
78.75
71.64
108.0
121.5
94.50
70.09
85.08
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
70.09
85.04
60.00
70.07
75.03
66.13
75.00
85.00
85.00
31.47
37.86
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
31.47
37.93
48.36
56.48
60.02
53.96
67.50
77.09
68.68
-/+
-/+
-/-
-/-
-/-
A
A
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A
VESA
VESA
VESA
VESA
SVGA
VESA
VESA
VESA
VGA
VESA
XGA
VESA
VESA
-/-
+/+
+/+
+/+
+/+
+/+
-/+
-/+
-/-
A
A/D
A/D
A/D
A/D
A/D
A/D
A/D
A/D
-/-
+/+
+/+
+/+
+/+
+/+
VESA
VESA
VESA
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Dot Clock
(MHz)
Vertical
Scanning
Frequency Frequency
Horizontal Sync Polarity or Operating
Scanning composite sync
Item
Standards
Resolution
Mode
(H/V)
(Hz)
(kHz)
28
29
30
31
32
33
34
35
36
37
VESA
VESA
VESA
VESA
SUN
SUN
SUN
SUN
SUN
1280x960
1280x1024
1280x1024
1280x1024
1024x768
1024x768
1024x768
1280x1024
1280x1024
1600x1200
108.0
108.0
127.0
135.0
64.13
74.25
84.38
117.0
135.0
162.0
60.0
60.0
+/+
+/+
+/+
A/D
A/D
A/D
A/D
A
A
A
A
A
60.02
69.85
75.03
59.98
70.04
77.07
67.19
76.10
60.00
63.98
74.88
79.98
48.29
56.59
62.04
71.69
81.13
75.00
+/+
H+V
H+V
H+V
H+V
H+V
+/+
VESA
A/D
*A=Analog Mode; D=Digital Mode
*Once a mode is optimized, there is no need to make any further adjustment as long as
the VGA card remains unchanged.
*Specifications are subject to change without notice.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C
Troubleshooting
Troubleshooting Procedures
This LCD Monitor was pre-adjusted in the factory with standard VGA timing. Due to output timing
differences among various VGA cards, you may initially experience an unstable or unclear display
when a new display mode or new VGA card is selected.
This LCD Monitor Supports Multiple VGA Modes. Refer to Addendum
for a listing of the factory preset modes supported by this LCD Monitor.
PROBLEM: Display is Unclear and Unstable
To stabilize and clarify your display, follow this procedure in this order:
1. It’s best to adjust the display on a screen displaying of vertical lines. In
Windows, load a wallpaper bitmap that has vertical lines in it. (Or you can
the select window shut down screen)
2. After you have the wallpaper loaded, open the OSD and select the “Clock”
function. Press the top (or bottom) Adjustment Control button and continue
pressing the button until you see vertical dark and light lines across the
screen.
3. When you can see distinct light and dark vertical bands, stop pressing the
Adjustment Control button. Now press the opposite (top or bottom)
Adjustment Control button. The vertical dark and light bands will decrease
in number. Keep pressing the button until the distinct bands disappear and
you have a clear display.
4. Next press the Function Control button to choose the “Phase” function. The
Phase will adjust the horizontal display. Press the top (or bottom)
Adjustment Control button and you will see horizontal dark and light lines
appear. The number of lines increases as you press the button. Now press
the bottom (or top) Adjustment Control button until the lines disappear and
you have a clear display.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: There is no LCD Display
If there is no display on the LCD, please perform the following steps:
1. Make sure that the power indicator on the LCD Monitor is lit, all
connections are secure, and the system is running on the correct
timing. Refer to the Addendum for information on timing.
2. Turn off the LCD Monitor and then turn it back on again. Press the
upper Function Control button (refer to Chapter 2) once and then
press either the upper or lower Adjustment Control button several
times. If there is still no display, press the other Adjustment Control
button several times.
3. If step 2 doesn’t work, connect your PC system to another external
CRT Monitor. If your PC System function properly with a CRT
Monitor but it does not function with the LCD Monitor and the LCD
Monitor’s power LED is blinking, the output timing of the PC’s
VGA card may be out of the LCD’s synchronous range. Please
change to an alternate mode listed in Addendum or replace the VGA
card and repeat steps 1 and 2.
4. If the PC (or Notebook PC) doesn’t function with the CRT monitor
neither, check BIOS to see if there is a Simultaneous Display setting
under the display mode item. Set the BIOS display mode to
Simultaneous Display or CRT and try again. If there is still no
display, then there may be a problem with your system. Contact
technical support.
5. If the power LED is not lit, check to see if the AC power connector
is securely connected. If the power LED is not lit, please contact
your dealer for assistance.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
02/04
6200507210
Download from Www.Somanuals.com. All Manuals Search And Download.
|