PT1503NT
Download from Www.Somanuals.com. All Manuals Search And Download.
PREFACE
About this manual
This manual is designed to assist you in setting up and using your New Planar
LCD Monitor. Information in this document has been carefully checked for
accuracy; however, no guarantee is given to the correctness of the contents. The
information in this document is subject to change without notice. This document
contains proprietary information protected by copyright. All rights are reserved.
No part of this manual may be reproduced by any mechanical, electronic or other
means, in any form, without prior written permission of the manufacturer.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Opeartion is subject to the
following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that
may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
inerference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
Reorient or relocate the receiving antenna.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
•
•
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use the
shielded signal cord supplied with this unit.
The Federal Communications Commission warns that changes or modifications
of the unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-
3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11)
Radio Frequency Interference Statement
Warning:
This is a Class B product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
Canadian Doc Notice
For Class B Computing Devices
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference Regulation
of the Canadian Department of Communications.
“Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de la class B prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada”
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained
for future use.
1. To clean the LCD monitor screen, first, make sure the monitor is in the
power off mode. Unplug the monitor from its power source before cleaning
it. Do not spray liquid cleaners directly onto the unit. Without applying
excessive pressure, clean the screen with a slightly dampened rag.
2. Do not place your LCD monitor near a window. Exposing the monitor to
rain, water, moisture, or sunlight can severely damage it.
3. Do not place anything on top of the monitor-to-PC signal cord. Make sure
the cord is placed in an area where it will not be stepped on.
4. Do not apply pressure to the LCD screen. Excessive pressure may cause
permanent damage to the display.
5. Do not remove the cover or attempt to service this unit by yourself. You
may void the warranty. Servicing of any nature should be performed only by
an authorized technician.
6. Safe storage of the LCD monitor is in a range of minus 20 to plus 60
degrees Celsius. Storing your LCD monitor outside this range could result
in permanent damage.
7. Immediately unplug your monitor and call an authorized technician when:
•
•
•
The power or monitor-to-PC signal cord is frayed or damaged.
Liquid has been spilled into the monitor, or it has been exposed to rain.
The monitor has been dropped or the case has been damaged.
8. Only with use of supplied adaptor, in case of loss or replacement contact the
retailer or service center.
9. If you lost the power cord that we given, you must to purchase a same
configuration/type of power cord (with ground-connection)
ꢀ
Japan： VCTF type, 3 wires or with ground-wire, T-mark approval is
required.
ꢀ
ꢀ
U.S.：VW-1; 18AWG X 3C; SVT with national approval as UL
and/or CSA approval/number(s)
Europe：VDE/ÖVE and/or KEMA approval; H05VV-F, 3G,
0.75mm2, or equivalent.
10. Above power cord should bear with the type and manufacturer name on..
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
TABLE OF CONTENTS
PREFACE..................................................................................................................I
TABLE OF CONTENTS.......................................................................................IV
CHAPTER 1 ............................................................................................................. 1
Unpacking......................................................................................................1
Identifying Components...............................................................................2
The LCD Monitor — Front View................................................................................ 2
The LCD Monitor — Rear View................................................................................. 3
Adjusting the Tilting Angle ..........................................................................3
Connecting AC Power, Video, Audio Cable and Touch Screen Cable
(optional)........................................................................................................4
Power Management System ........................................................................4
CHAPTER 2 ............................................................................................................. 5
LCD Monitor Control Panel..........................................................................5
Adjusting the Monitor’s Display..................................................................6
OSD Main Menu......................................................................................................... 6
Hot-Key Buttons for Quick Adjustment of Monitor Settings..................10
APPENDIX A ......................................................................................................... 11
Planar TFT LCD Monitor Specifications ...................................................11
APPENDIX B.......................................................................................................... 13
Timing for Model PT1503NT (XGA Resolution) .......................................13
APPENDIX C ......................................................................................................... 14
Troubleshooting Procedures.....................................................................14
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
The LCD Monitor
Unpacking
After you unpack your LCD monitor, make sure the
following items are included in the box and in good
condition:
Standard Item
•
•
•
•
•
•
•
LCD monitor
AC/DC adapter
Monitor to PC signal cable
Power cord
Landing Strip
This user’s manual
CD Manual
Optional Items
•
1.5M Stereo Jack audio cable
•
1.5M Touch Panel cable with RS232 connector
If you find that any of these items are missing or appear damaged, contact your
dealer immediately. Do not throw away the packing material or shipping
carton in case you need to ship or store the LCD monitor in the future.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Identifying Components
The LCD Monitor — Front View
Figure 1-1: The LCD Monitor Front View
1. Power-On Indicator
This LED indicator stays lit when the power is on and blinks
when the LCD monitor is in power saving mode.
2. Monitor Stand
3. LCD Screen
The LCD monitor screen is a 15-inch TFT 1024 x 768 screen.
4. LCD Monitor Control Panel
Refer to Chapter 2 for a detailed.
5. Stereo Speakers(optional)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
The LCD Monitor — Rear View
Figure 1-2: LCD Monitor Rear View
1. Audio Line-in (optional)
2. DC Power Jack
3. LCD monitor’s VGA Connector
4. RS-232 connector for Touch Screen (optional)
Adjusting the Tilting Angle
The LCD monitor’s angle settings range from -5° to 25°. See Figure 1-3.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Figure 1-3: Tilting the Monitor
Connecting AC Power, Video, Audio Cable and Touch
Screen Cable (optional)
Turn off your PC and the LCD monitor before connecting your LCD monitor
to the computer.
Power Management System
The LCD monitor complies with the VESA DPMS power management
proposal.
When the LCD monitor is in power saving mode or detects an incorrect timing,
the monitor screen will be blank and the power LED indicator starts blinking.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
The Display Controls
LCD Monitor Control Panel
Figure 2-1: The LCD Monitor Panel
1. OSD Menu Button
Press this button to pop up the OSD (On-Screen Display) menu.
This button is also a Function Select button.
2. Adjustment Control Buttons
These two buttons allow you to adjust and apply selected
control functions in the OSD.
3. Function Select Buttons
These two buttons allow you to select the control functions in
the OSD. Press either button to scroll through the main menu
and submenu items.
4. Power Switch
Push the power switch to turn the monitor on and off. This
switch is also a hot-key button to close the OSD menu while the
OSD appears.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Adjusting the Monitor’s Display
OSD Main Menu
To access the OSD main menu, press the OSD Menu button. Use the Function
Select buttons to scroll between the OSD main menu options. The option that
is currently selected is highlighted.
Pressing the OSD Menu button causes the following screen to appear:
Figure 2-2: The OSD Main Menu
The Auto Adjust Option
Choosing the Auto Adjust option lets the monitor determine and select the settings
that are most appropriate for your system requirements.
With the Auto Adjust icon selected, press the Adjustment control
button to apply the monitor settings automatically.
The Monitor-Control Option
The Monitor-Control option allows you to adjust the LCD monitor’s display
settings.
Press Adjustment control button to display the submenu.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
H-Position: To move the LCD monitor’s display left or right on a
horizontal plane.
V-Position: To move the LCD monitor’s display up or down on a
vertical plane.
Phase: To adjust the focus and clarity of the display.
Clock: To adjust the display pixel alignment.
Reset: To reset all of the Monitor-Control submenu settings.
Exit: To exits the Monitor-Control submenu.
OSD-Control Option
The OSD-Control menu option lets you adjust the position of the OSD on the screen.
Press the Adjustment control button to display the submenu.
Use the Function Select buttons to select one of the following
submenu options:
OSD-H-Position: To change the position of the OSD on a
horizontal plane.
OSD-V-Position: To change the position of the OSD on a vertical
plane.
Exit: To exit the OSD-Control submenu.
Misc-Control Option
The Misc-Control menu option lets you select the OSD display language, adjust the
volume setting and view system information.
Press the Adjustment control button to display the submenu.
Language: The supported languages include German, English,
French, Spanish, Italian and Japanese.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Audio Volume (optional): To increase or decrease the volume of
the LCD monitor’s sound system.
Information: To indicate display mode and firmware version.
Exit: To exit the Misc-Control submenu.
Graphic-Control Option
The Graphic-Control option lets you make adjustments that effect the contrast,
brightness and color of the LCD monitor’s display.
Press the Adjustment control button to display the submenu.
Contrast: To adjust the contrast level of the display screen.
Brightness: To adjust the light level on the display screen.
Color: To select the LCD monitor’s color display. The available
options are 9300, 6500 and User. Selecting the user option lets
you make individual adjustments to the R, G and B items.
R, G and B: To make individual adjustments to the Red, Blue,
Green (RGB) gain for the color temperature.
Auto Level: To adjust automatically to perfect the white balance
display.
Exit: To exit the Graphic-Control submenu.
Graph/Text Option
The Graphic/Text option lets you switch between text and graphic display modes.
Press the Adjustment button to switch between the text and graphic
options.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Exit Option
Use the OSD Exit item to close the OSD menu.
The OSD will close by itself if left inactive.
Note:
1.
No Video
When the monitor is ON and there is no
Video signal received, the following
message will be displayed.
2.
Signal out of monitor’s supported range
(Please refer to Addendum)
When the frequency range of the signal is out of the monitor’s specifications,
the display will show the following message on two cases:
Case 1:
The incoming frame rate is higher than
75Hz.
In this case, the screen display may not be
centered and a warning message appears.
Case 2:
The incoming resolution is higher than
1024x768.
In this case, the video data will be turned off
and a warning message appears at center.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Hot-Key Buttons for Quick Adjustment of Monitor Settings.
1.”Auto-adjust” hot-key button:
Press the 2nd function button to apply
the monitor setting automatically. A
small “Auto Adjust” OSD is also
displayed.
2.”Contrast-adjust” hot-key button:
Press the 1st adjustment control button
to allow you to adjust the contrast of
the display directly. A small “Contrast”
OSD is also displayed.
3.” Adjust-volume” hot-key button
(Optional):
Press 2nd adjustment control button to
allow you to adjust the audio volume
directly. A small “Audio Volume”
OSD is also displayed.
* To close the small OSD windows, press the power switch
10
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
Technical Information
Planar TFT LCD Monitor Specifications
Model
Planar PT1503NT
LCD Panel
15"XGA
Control Functions
Power
Software Power switch with LED indicator
(ON/OFF)
On-Screen Display
(OSD)
Main Menu
Submenu
Auto
Adjust
Monitor
Control
Horizontal Position/Vertical
Position/Phase/Clock/Reset/Exit
OSD
Control
OSD Horizontal Position/OSD
Vertical Position/Exit
Misc.
Language/Audio
Control
Volume(optional)/Information/Exit
Graphic
Control
Contrast/Brightness/Color/R/G/B
Auto Level/Exit
Graph/Te 640 x 400/720 x 400
xt
OSD
Exit
Display Area (mm)
304.1 x 228.1
(15" diagonal)
Display Colors
Video Interface
16.2M
VGA Compatible Analog RGB
Composite Sync.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Power Management
Meets VESA DPMS
33/5Max.
Power
Consumption
(ON/OFF, W)
Dimensions
WxHxD mm
408 X 388 X 175
5.8
Net Weight (Kg)
Approx.
Power Supply
12V/3A, 36W
Universal Input AC Adapter (External)
Environment
Operating Temperature: 0 to 40° C
Relative Humidity: 20% to 85%
Yes (optional)
Audio (Two 1 Watt
speakers with
amplifier)
Regulatory
UL, CUL, TÜV-GS, CE Mark, VCCI, FCC B DoC,
TÜV-Ergonomics
12
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
Supported Timing
Timing for Model PT1503NT (XGA Resolution)
Vertical
Horizontal
Scanning
Frequency
(kHz)
Scanning
Frequency
(Hz)
Item
Standards
Resolution
Dot Clock
(MHz)
1
2
NEC PC98
NEC PC98
MAC 13" mode
MAC 16" mode
MAC 17" mode
VGA
640x400
640x400
640x480
832x624
1024x768
640x350
640x400
640x480
640x480
640x480
800x600
800x600
800x600
800x600
720x400
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
25.20
21.05
30.24
57.28
80.00
25.18
25.18
25.18
31.50
31.50
36.00
40.00
50.00
49.50
28.32
65.00
75.00
78.75
71.64
64.13
74.25
84.38
70.15
56.42
66.67
74.55
75.02
70.09
70.09
59.94
72.81
75.00
56.25
60.32
72.19
75.00
70.09
60.00
70.07
75.03
66.13
59.98
70.04
77.07
31.50
24.83
35.00
49.73
60.24
31.47
31.47
31.47
37.86
37.50
35.16
37.88
48.08
46.88
31.47
48.36
56.48
60.02
53.96
48.29
56.59
62.04
3
4
5
6
7
VGA
8
VGA
9
VESA
10
11
12
13
14
15
16
17
18
19
20
21
22
VESA
VESA
SVGA
VESA
VESA
VGA
XGA
VESA
VESA
SUN
SUN
SUN
*Once a mode is optimized, there is no need to make any further adjustment as long as the
VGA card remains unchanged.
*Specifications are subject to change without notice.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C
Troubleshooting
Troubleshooting Procedures
This LCD monitor comes pre-adjusted with standard VGA timing. Due to
output timing differences among various VGA cards, you may initially
experience an unstable or unclear display when a new display mode or new
VGA card is selected.
Before applying any of the following troubleshooting procedures, you should
first apply the Auto Adjust option in the OSD menu.
PROBLEM: Display is Unclear and Unstable
To stabilize and clarify your display, follow this procedure:
1. In Windows, enter the windows shut down screen.
2. Open the OSD and select the Clock function. Press one of the
Adjustment Control buttons until the dark vertical bands
disappear.
3. Select the Phase function and press one of the Adjustment
Control buttons until horizontal dark and light lines appear. The
number of lines increases as you press the button. Press the
other Adjustment Control button until the lines disappear and
you have a clear display.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: There is no LCD Display
If there is no display on the LCD, refer to the following:
1. Make sure that the power indicator on the LCD monitor is lit,
all connections are secure, and the system is running on the
correct timing. Refer to the Addendum for information on
timing.
2. Turn off the LCD monitor and then turn it back on again. Press
the OSD Menu button (refer to Chapter 2) once and then press
either Adjustment Control button several times. If there is still
no display, press the other Adjustment Control button several
times.
3. If step 2 doesn’t work, connect your PC system to another
external CRT. If your PC system functions properly with a CRT
monitor but it does not function with the LCD monitor, and the
LCD monitor’s power LED is blinking, the output timing of the
PC’s VGA card may be out of the LCD’s synchronous range.
Change to one of the alternate modes, listed in the Addendum,
or replace the VGA card and repeat steps 1 and 2.
4. If the power LED is not lit, check that the AC power connector
is securely connected. Verify that the AC adapter LED is lit. If
the AC adapter LED is not lit, please contact Planar for
assistance..
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|