Planar Car Video System PX2211 MW User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

The information contained in this document is subject to change without notice.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be reproduced, translated to

another language or stored in a retrieval system, or transmitted by any means,

electronic, mechanical, photocopying, recording, or otherwise, without prior written

permission. Windows is a registered trademark of Microsoft Inc.

Other brand or product names are trademarks of their respective holders.

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

For your safety------------------------------------------------------ 5

Safety precautions -------------------------------------------6

Special notes on lcd monitors -----------------------------7

Before you operate the monitor --------------------------------7

Features --------------------------------------------------------7

Packing list ------------------------------------------------------7

Installation instructions -------------------------------------8

Controls and connectors ------------------------------------9

Adjusting the viewing angle------------------------------- 10

Operating instructions ------------------------------------------- 11

General instructions ----------------------------------------- 11

Front panel control -------------------------------------- 12

How to adjust a setting ----------------------------------- 13

Adjusting the picture ---------------------------------- 14-17

Plug and play ----------------------------------------------- 18

Technical support (FAQ) -------------------------------------- 19

Error message & possible solution ------------------- 20

Appendix -------------------------------------------------------------21

Specifications -------------------------------------------- 21

Factory preset timing table ------------------------------ 22

Connector pin assignment ------------------------------ 23-24

---------------25

Product registration and technical support

Download from Www.Somanuals.com. All Manuals Search And Download.

FOR YOUR SAFETY

Before operating the monitor, please read this manual thoroughly. This manual

should be retained for future reference.

FCC Class B Radio Frequency Interference Statement

WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy, and if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE:

The changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

Shielded interface cables and AC power cord, if any, must be used in order to

comply with the emission limits.

The manufacturer is not responsible for any radio or TV interference caused

by unauthorized modification to this equipment. It is the responsibilities of

the user to correct such interference.

WARNING:

To prevent fire or shock hazard, do not expose the monitor to rain or moisture.

Dangerously high voltages are present inside the monitor. Do not open the cabinet.

Refer servicing to qualified personnel only.

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

ꢀ

Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink,

laundry tub, swimming pool or in a wet basement.

ꢀ Do not place the monitor on an unstable cart, stand, or table. If the monitor falls,

it can injure a person and cause serious damage to the appliance. Use only a

cart or stand recommended by the manufacturer or sold with the monitor. If

you mount the monitor on a wall or shelf, use a mounting kit approved by the

manufacturer and follow the kit instructions.

ꢀ

Slots and openings in the back and bottom of the cabinet are provided for

ventilation. To ensure reliable operation of the monitor and to protect it from

overheating, be sure these openings are not blocked or covered. Do not place

the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor

near or over a radiator or heat register. Do not place the monitor in a bookcase

or cabinet unless proper ventilation is provided.

ꢀ

The monitor should be operated only from the type of power source indicated

on the label. If you are not sure of the type of power supplied to your home,

consult your dealer or local power company.

The monitor is equipped with a three-pronged grounded plug, a plug with a

third (grounding) pin. This plug will fit only into a grounded power outlet as a

safety feature. If your outlet does not accommodate the three-wire plug, have

an electrician install the correct outlet, or use an adapter to ground the

appliance safely. Do not defeat the safety purpose of the grounded plug.

Unplug the unit during a lightening storm or when it will not be used for long

period of time. This will protect the monitor from damage due to power surges.

Do not overload power strips and extension cords. Overloading can result in

fire or electric shock.

Never push any object into the slot on the monitor cabinet. It could short

circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

Do not attempt to service the monitor by yourself; opening or removing covers

can expose you to dangerous voltages and other hazards. Please refer all

servicing to qualified service personnel.

ꢀ

To ensure satisfactory operation, use the monitor only with UL listed computers

which have appropriate configured receptacles marked between 100 - 240V AC,

Min. 5A.

The wall socket shall be installed near the equipment and shall be easily

accessible.

Important Recycle Instruction:

Lamp(s) inside this product contain mercury and must be recycled or disposed

of according to local, state or federal laws. For more information, contact the

electronic industries alliance at WWW.EIAE.ORG. For lamp specific disposal

information check WWW.LAMPRECYCLE.ORG.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitor and do not indicate a

problem.

NOTES

ꢀ

Due to the nature of the fluorescent light, the screen may flicker during initial

use. Turn off the Power Switch and then turn it on again to make sure the flicker

disappears.

ꢀ

You may find slightly uneven brightness on the screen depending on the

desktop pattern you use.

The LCD screen has effective pixels of 99.99% or more. It may include blemishes

of 0.01% or less such as a missing pixel or a pixel lit all of the time.

Due to the nature of the LCD screen, an afterimage of the previous screen may

remain after switching the image when the same image has been displayed for

a long time. The monitor will slowly recover from this.

ꢀ

When the screen becomes black or flashing, or cannot illuminate any more,

contact your dealer or service center to replace parts. Don’t repair the screen by

yourself!

BEFORE YOU OPERATE THE MONITOR

FEATURES

ꢀ

21.5"(546mm) TFT Color LCD monitor

16:9 Widescreen

Crisp, Clear Display for Windows

Recommened Resolutions: 1920X 1080@60Hz

Ergonomic Design

Space Saving, Compact Case Design

CHECKING THE CONTENTS OF THE PACKAGE

The product package should include the following items:

1. LCD monitor

2. Base

3. User's Guide

4. Power Cord

5. D-sub Cable

DVI Cable

7. Audio Cable

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

BASE

ꢀ

The monitor is supplied complete with a stand.If you prefer to wall mount the monitor,

please follow the instructions below to remove the stand.Be sure to include the stand

with the monitor if it is necessary to return the unit.

CAUTION

Put the monitor on a stable surface.The monitor may cause injury

or damage if it falls or is dropped.

Do not give a strong impact to the monitor.It may cause damage.

Ƶꢀ

ꢀ

Ƶꢀ

ƵꢀUnplug the monitor before removal or installation to avoid electric

shock or damage.

ꢀ

Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.

ꢀꢁꢂꢃthe monitor flat on a table with front face down.

Install the Stand-Base to the Monitor.

Av‘ꢃ‡urꢃ€‚v‡‚ꢄꢃ‡‚ꢃ‡urꢃ†‡ꢁqꢃiꢂꢃˆ†vtꢃ‡urꢃ†pꢄrꢅꢃPprꢃ†pꢄrꢃv†ꢃ†rpˆꢄryꢂꢃsꢁ†‡rrqꢆꢃƒˆ†uꢃq‚ꢃ

‡urꢃx‚iꢃ‚ꢃ‡urꢃ†pꢄrꢅ

The knob of the screw

push down

Stand-Base

Screw for Stand-Base fixing

Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.

ꢀꢁꢂꢃthe monitor flat on a table with front face down.

Pull up the knob of the screws, and remove the screw and the Stand-Base.

Please stand the monitor and then remove the

stopper pin on the back of the stand slowly while

pushing top face of the stand before you install the

monitor. Careful attention is required as the monitor

is sprung loaded and may expand quickly when

removing it.

Stopper pin

Download from Www.Somanuals.com. All Manuals Search And Download.

ꢀ

CONTROLS AND CONNECTORS

SIGNAL CABLE

Connecting the Signal Cable: Plug one end of the signal cable to the LCD monitor

and the other end to a computer or a video source.

Connecting the Power Cord: Plug the AC-power cord one end to LCD monitor’s

AC input socket , the other end to Wall outlet.

Connecting the Audio Cable: Connect the audio cable between the monitor's

audio input and the PC's audio output.

Caution: If the AC outlet is not grounded (with three holes), install the proper

grounding adapter (not supplied).

Figure 2 Connecting Cables

1. Power Cable

2. HDMI Cable

DVI Cable

D-SUB Cable

Audio Cable

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE VIEWING ANGLE

ꢀ

For optimal viewing it is recommended to look at the full face of the monitor,

then adjust the monitor’s angle to your own preference.

Hold the stand so you do not topple the monitor when you change the

monitor’s angle.

You are able to adjust the monitor’s angle from -5ꢁ to 19ꢁ.

19°

-5°

Figure 3

NOTES

ꢀ

Do not touch the LCD screen when you change the angle. It may cause damage

or break the LCD screen.

Careful attention is required not to catch your fingers or hands when you

change the angle.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

GENERAL INSTRUCTIONS

Press the power button to turn the monitor on or off. The other control buttons are

located at front panel of the monitor (See Figure 4). By changing these settings, the

picture can be adjusted to your personal preferences.

ꢀ

The power cord should be connected.

Connect the video cable from the monitor to the video card.

Press the power button to turn on the monitor position. The power indicator

will light up.

Figure 4 External Control Button

EXTERNAL CONTROLS

1. Source/AutoAdjust/EXIT

button

ECO (-)

3. Volume Hotkey(+)

4. Menu / Enter

5. Power Indicator

6. Power button

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

FRONT PANEL CONTROL

ꢀ

Power Button:

Press this button to switch ON/OFF monitor’s power.

ꢀ Power Indicator :

Blue --- Power On mode.

Orange --- Power saving mode.

ꢀ MENU/ENTER:

Activates OSD menu or function adjust confirm .

ꢀ

ECO/(-)

Activates the ECO control when the OSD is OFF or navigate through adjustment icons

when OSD is ON or adjust a function when function is activated.

ꢀ Volume/+:

Activates the volume control when the OSD is OFF or navigate through adjustment

icons when OSD is ON or adjust a function when function is activated.

ꢀ Source/Auto Adjust/Exit:

When the OSD is OFF, pressing Auto/Source button will toggle between sources.

Press continuously to select the input source indicated in the message bar.Press

Menu/Enter button to change to the selected source.

Auto configure hot key:(VGA input only) When the OSD is OFF,press and hold down

the button for 2 seconds to auto configure.

when OSD menu is ON, this button will act as a Exit Key (Exit OSD menu)

OSD Lock Function: To lock the OSD, press and hold the MENU button while the

monitor is off and then press power button to turn the monitor on. To un-lock the

OSD - press and hold the MENU button while the monitor is off and then press

power button to turn the monitor on.

NOTES

ꢀ

Do not install the monitor in a location near heat sources such as radiators or air

ducts, or in a place subject to direct sunlight, or excessive dust or mechanical

vibration or shock.

ꢀ

Save the original shipping carton and packing materials, as they will come in

handy if you ever have to ship your monitor.

For maximum protection, repackage your monitor as it was originally packed at

the factory.

To keep the monitor looking new, periodically clean it with a soft cloth.

Stubborn stains may be removed with a cloth lightly dampened with a mild

detergent solution. Never use strong solvents such as thinner, benzene, or

abrasive cleaners, since these will damage the cabinet. As a safety precaution,

always unplug the monitor before cleaning it.

It may cause permanent damage

ꢀ

do not scratch the screen with hard things,

Don’t leak liquid into monitor which will result in the damage of component

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO ADJUST A SETTING

1. Press the MENU-button to activate the OSD window.

2. Press + or - to navigate through the functions. Once the desired function is

highlighted, press the MENU-button to activate it. If the function selected has a

sub-menu, press + or - again to navigate through the sub-menu functions.

Once the desired function is highlighted, press MENU-button to activate it.

3. Press + or - to change the settings of the selected function.

4. To exit and save, select the exit function. If you want to adjust any other

function, repeat steps 2-3.

Figure 5 The OSD Message

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE PICTURE

Main

Icon

Main Menu

Item

Sub

Description

Enhances Contrast Ratio

Note: When this function is turned "On" you cannot

adjust the current settings for Contrast, Brightness,

ECO mode or Gamma.

(VGA input

only)

(VGA input

only)

(VGA input

only)

(VGA input

only)

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

Main

Icon

Main Menu

Item

Sub

Description

Download from Www.Somanuals.com. All Manuals Search And Download.

Main

Icon

Main Menu

Item

Sub

Description

Download from Www.Somanuals.com. All Manuals Search And Download.

Main

Icon

Main Menu

Item

Sub

Description

Download from Www.Somanuals.com. All Manuals Search And Download.

PLUG AND PLAY

Plug & Play DDC 2B Feature

This monitor is equipped with VESA DDC 2B capabilities according to the VESA

DDC STANDARD. It allows the monitor to inform the host system of its identity and,

depending on the level of DDC used, communicate additional information about

its display capabilities.

The DDC 2B is a bidirectional data channel based on the I2C protocol. The host can

request EDID information over the DDC 2B channel.

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO

INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE

MUST BE A VIDEO INPUT SIGNAL.

This monitor meets the Green monitor standards as set by the Video Electronics

and The Swedish Confederation Employees (NUTEK).

Standards Association (VESA)

consumption

This feature is designed to conserve electrical energy by reducing power

when

there is no video-input signal present. When there is no video input signal

this monitor, following a time-out period, will automatically switch to an OFF mode.

This reduces the monitor's internal power supply consumption. After the video

input signal is restored, full power is restored and the display is automatically

redrawn. The appearance is similar to a "Screen Saver" feature except the display is

completely off. The display is restored by pressing a key on the keyboard, or

clicking the mouse.

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL SUPPORT (FAQ)

Problem & Question

Possible Solution

*Check if the Power Switch is in the ON

position

Power LED is not on

*Power Cord should be connected

*Check if the PC system is Plug & Play

compatible

*Check if the Video Card is Plug & Play

compatible

No Plug & Play

Picture is fuzzy

*Check if the D-15 plug pin of Video Cable

is bent

*Adjust the Contrast and Brightness

Controls.

*Move electrical devices that may cause

electrical interference.

Picture bounces or a wave

pattern is present in the picture

*Computer Power Switch should be in the

ON position.

*Computer Video Card should be snugly

seated in its slot.

*Make sure monitor’s video cable is

properly connected to the computer.

*Inspect monitor’s video cable and make

sure none of the pins are bent.

*Make sure computer is operational by

hitting the CAPS LOCK key on the

keyboard while observing the CAPS LOCK

LED. The LED should either turn ON or

OFF after hitting the CAPS LOCK key.

The power LED is ON but there’s

no video or no picture.

Missing one of the primary colors *Inspect the monitor’s video cable and

(RED, GREEN, or BLUE)

Screen image is not centered or

sized properly.

Picture has color defects

(white does not look white)

make sure that none of the pins are bent.

*Adjust pixel frequency (CLOCK) and FOCUS

or press hot-key (AUTO).

*Adjust RGB color or select color

temperature.

*Use win 95/98 shut-down mode Adjust

CLOCK and FOCUS or perform hot- key

(AUTO-key).

Horizontal or vertical disturbances

on the screen

CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal

sweep. If the frequency is not correct, the screen shows vertical stripes and the

picture has not correct width.

FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment

the picture has horizontal disturbances in light picture.

For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down mode

pattern.

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

ERROR MESSAGE & POSSIBLE SOLUTION

NO SIGNAL :

Check that the signal-cable is properly connected , If the connector is loose,

tighten the connector’s screws.

Check the signal-cable’s connection pins for damage.

INPUT NOT SUPPORT :

Your computer has been set to unsuitable display mode ,set the computer to

display mode given in the following table.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

SPECIFICATIONS

Driving system TFT 21.5"Color LCD

Viewable

546mm diagonal

Image Size

LCD Panel

Input

Pixel pitch 0.248˄H˅× 0.248˄v˅

R, G, B Analog Interface

DVI

HDMI

Video

Separate Sync. H/V TTL

H-Frequency Analog:24-80kHz,Digital:30kHz–83kHz

V-Frequency Analog&Digital:56-76Hz

170MHz

Dot Clock

Max. Resolution

Plug & Play

1920x1080@60Hz

VESA DDC2B ^TM

≤43W(TYP)

ON Mode

Power Consumption

OFF Mode ≤1W

D-Sub mini 15 pin, DVI-D 24 pin, HDMI

Input Connector

Analog:0.7Vp-p(Standard)75Ω, Positive

Digital:DVI(Digital Visual Interface

Standard Rev.1.0) compliance

Digital:HDMI(1.3)

Input Video Signal

Power Source

100~240VAC,50/60Hz

Operating Temp: 5° to 40°C

Environmental

Considerations

Storage

Temp.: -20° to 60°C

Operating umidity:15% to 90%

Dimension

Weight (N. W.)

512.7(W)X398.1(H) X249.7(D)

6.3 kg

Power Consumption ( Maximum )

52Watts

UL cUL, CE , FCC B

Regulatory Compliance

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

FACTORY PRESET TIMING TABLE

HORIZONTAL

FREQUENCY(kHZ)

VERTICAL

FREQUENCY(Hz)

STANDARD

RESOLUTION

640 x 480

720 x 400

800 x 600

832 x 624

1024 x 768

1280 x 1024

1440 x 900

1680 x1050

1920 X1080

31.469

37.861

37.5

59.94

66.667

72.809

70.087

56.25

60.317

72.188

74.551

60.004

70.069

72.074

75.029

60.02

VGA

Mac VGA

Dos-mode

31.469

35.156

37.879

48.077

46.875

49.726

48.363

56.476

57.5

60.023

67.981

79.976

55.935

70.635

65.29

SVGA

Mac SVGA

XGA

SXGA

75.025

59.887

74.984

59.954

59.887

WXGA+

WSXGA+

HDTV

66.295

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTOR PIN ASSIGNMENT

15 - Pin Color Display Signal Cable

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

+5V

Detect Cable

Ground

DDC-Serial Data

H-Sync

V-Sync

Red

Green

Blue

Ground

R-Ground

G-Ground

B-Ground

10.

11.

12.

13.

14.

15.

DDC-Serial Clock

24 - Pin Color Display Signal Cable

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

TMDS Data 2-

TMDS Data 2+

TMDS Data 2/4

Shield

13.

14.

15.

TMDS Data 3+

+5V Power

Ground(for+5V)

TMDS Data 4-

TMDS Data 4+

DDC Clock

16.

17.

18.

19.

Hot Plug Detect

TMDS Data 0-

TMDS Data 0+

TMDS Data 0/5

Shield

TMDS Data 5-

TMDS Data 5+

TMDS Clock Shield

DDC Data

10.

11.

N.C.

20.

21.

22.

23.

TMDS Data 1-

TMDS Data 1+

TMDS Data 1/3

Shield

TMDS Clock +

TMDS Clock -

12.

TMDS Data 3-

24.

Download from Www.Somanuals.com. All Manuals Search And Download.

No.

Signal Name

Pin No.

Signal Name

TMDS Data 2+

TMDS Data 0

DDC/CEC

Ground

TMDS Data 2

Shield

TMDS Data 2

TMDS Clock +

+5V Power

TMDS Clock

Shield

Hot Plug

Detect

TMDS Clock

TMDS Data 1+

TMDS Data

1Shield

CEC

TMDS Data 1

Reserved (N.C.

on device

TMDS Data 0+

SCL

TMDS Data 0

Shield

SDA

ꢀ

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Registration and Technical Support

Thank you choosing Planar. To assure you receive all the benefits of your Planar

product and services, register your Planar product today.

Visit our website to register your productat

http://www.planar.com/support/product_registration.html

Cables, Replacement Lamps, Accessories

To find cables, replacement lamps and accessories for your Planar projector, LCD

monitor, touch screen or other Planar products visit our online store at

www.PlanarOnline.com or find other stores who carry Planar products at

http://www.planar.com/howtobuy

Technical Support

Visit Planar at http://www.planar.com/support for product registration, operations

manuals, touch screen drivers, warranty information and access to Planar's

Technical Library for online troubleshooting.

To speak with Planar Customer Support please have you model and serial number

available and dial:

Planar Support

Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US. Hours: 24

hours a day, 7 days a week.

Toll or long distance charges may apply.

Download from Www.Somanuals.com. All Manuals Search And Download.

Q41G22M1935 1A

Download from Www.Somanuals.com. All Manuals Search And Download.

Pelco Switch CM9700UTP32A User Manual
Pentax Binoculars 10X50PIF User Manual
Philips Cable Box 22IE User Manual
Philips Car Speaker SB365 User Manual
Philips Charcoal Grill HD 4631 User Manual
Philips CRT Television 13PR19C1 User Manual
Philips DVD Player BDP5110 User Manual
Philips Work Light HO User Manual
Plantronics Headphones CS510 User Manual
Poulan Snow Blower 421916 User Manual