Pelco Switch CM9700UTP32A User Manual
I N S T A L L A T I O N  
CM9700UTP Series  
Multichannel  
Active Receivers  
16 or 32 Channels  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Back Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Desktop Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Power and Video Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Cable Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Installing the Jumpers for CE Compliance (only CM9700UTP16A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
INSTALLING THE JUMPERS FOR CE COMPLIANCE (ONLY CM9700UTP32A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Color Video Range Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Black-White or Day/Night Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Advance Color Video Signal Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Advance Black-White Video Signal Settings (Day/Night Cameras) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Fan Filter: Cleaning or Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Fan Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
C3646M-C (6/09)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Illustrations  
1
2
3
4
5
6
7
8
9
CM9700UTP16A Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
CM9700UTP32A Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
CM9700UTP16A Back Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
CM9700UTP32A Back Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
RJ-45 Connector Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Using the Wire Assembly Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Installing the Jumpers for CE Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Factory Default Dial Position (32-channel model shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
DIP Switch Locations with Front Panel Removed (32-channel model shown). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
10 Color Burst and Sync are per Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
11 Ideal Video Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
12 Ideal Black-White Video Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
13 High Gain Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
14 Fan Filter Replacement (32-channel model shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
15 Fan Replacement (32-channel model shown). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
16 Remove Front Panel (32-channel model shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
List of Tables  
A
RJ-45 Pin Designations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
B
C
D
E
Cable Distance with TW4001P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Wire Gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Rotary Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
4
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.  
A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided  
plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from  
the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Unplug this apparatus during lightning storms or when unused for long periods of time.  
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-  
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the  
apparatus.  
15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.  
16. Installation should be done only by qualified personnel and conform to all local codes.  
17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not  
be installed where exposed to rain and moisture.  
18. Use only installation methods and materials capable of supporting four times the maximum specified load.  
19. A CCC-approved power cord must be used to power this equipment when used in China.  
C3646M-C (6/09)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Regulatory Notices  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
•
•
•
•
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This  
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this  
equipment under Federal Communications Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
6
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Description  
The CM9700UTP Series multichannel active receiver is a 16- or 32-channel unit that can receive live video over unshielded twisted pair (UTP)  
cable. The front panel of each model contains a dial and a LED per channel; dials are used for selecting cable distance. The back panel of each  
model features BNC connectors for video output, RJ-45 video input connectors, and video ribbon cable to connect to a CM9700 Series matrix.  
Models  
CM9700UTP16A  
CM9700UTP32A  
16-channel active receiver; 16 BNC connectors, four RJ-45 video input connectors, and one ribbon cable connector  
32-channel active receiver; 32 BNC connectors, eight RJ-45 video input connectors, and two ribbon cable connectors  
Parts List  
Qty Description  
1
1
CM9700UTP Series multichannel active receiver (CM9700UTP16A or CM9700UTP32A)  
Power cord (USA, UK, or EU standard)  
8 or 4 (Depending on the model) Cat5e cable assembly; mating connector provided and installed by user  
4
4
4
4
Screws, 10-32 x 0.50-inch, Phillips pan head  
Cage nuts, 10-32  
Protective bumpers, 0.75-inch, recessed  
Screws, 8-32 x 0.25-inch, Phillips pan head  
16 Jumpers (only for CM9700UTP16A; required for CE compliance)  
CM9700UTP Series Installation manual  
1
C3646M-C (6/09)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
FRONT PANEL  
Figure 1. CM9700UTP16A Front Panel  
16  
32  
15  
31  
14  
30  
13  
29  
12  
28  
11  
27  
10  
26  
9
8
7
6
5
4
3
2
1
25  
24  
23  
22  
21  
20  
19  
18  
17  
1
2
3
MADE IN USA  
Figure 2. CM9700UTP32A Front Panel  
ì Pelco Badge: Glows blue when the unit has power. When the temperature rises above the specified temperature (95°F [35°C]), or when  
any of the fans fail, the Pelco badge LED will blink and a buzzer will sound indicating there is an alarm condition.  
î Distance Rotary Switch: The manual selection of the gain for correct cable distance. Channels on both models are numbered right to  
left. The 16-channel unit is numbered 1 to 16; the 32-channel unit is numbered 1 to 16 and 17 to 32.  
ï Video Activity Indicators: Sixteen or thirty-two LEDs (depending on model) indicate video activity, the type of video (color or black-  
white), and the status of the video being received. Indicator colors differ depending on the type of video connected to the units; LEDs for  
color video are different than the color indicators for black-white video.  
• Green: Indicates that color video is being received.  
• Orange: Indicates that black and white video is being received, or the color video range setting is wrong.  
• Red: Indicates that no video is being received, or the video range setting is wrong.  
ñ Fans: Maintain the unit’s internal temperature within the specified range if the ambient operating temperature is at or below 95°F (35°C).  
All fans are removable and field replaceable. For information about maintaining the fan and fan filter, refer to Maintenance on page 17.  
ó Fan Alarm Indicators: Glow red when an alarm triggers due to a fan failure.  
8
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
BACK PANEL  
Figure 3. CM9700UTP16A Back Panel  
1-4  
5-8  
9-12  
13-16  
29-32  
1
17  
2
18  
3
19  
4
20  
5
21  
6
22  
7
23  
8
24  
9
25  
10 26  
11 27  
12 28  
13 29  
14 30  
15 31  
16 32  
TO MXB  
17-20  
21-24  
25-28  
100-240 VAC 50-60Hz 75A  
Figure 4. CM9700UTP32A Back Panel  
ì AC Power Connector: Connects the UTP receiver to the mains power supply (100 to 240 VAC, 50 to 60 Hz, autoranging).  
î BNC Connectors: There are 16 or 32 coaxial video outputs (depending on model) for each unit. BNC connectors on both models are  
numbered right to left. The 16-channel unit is numbered 1 to 16; the 32-channel unit is numbered 1 to 16 and 17 to 32.  
ï Ribbon Cable Connectors: Connects to a CM9700 Series matrix for video output.  
ñ
RJ-45 Connectors: Video input from either the TW3016-PATCH1, TW3032-PATCH1, or wire assembly cable (part #WA01-5104-005AG).  
Each connector has eight pins for UTP connection.  
C3646M-C (6/09)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installation  
RACK MOUNTING  
Install the CM9700UTP Series active receiver in a standard 19-inch (48.26 cm) equipment rack using standard mounting hardware (10-32 cage  
nuts and 10-32 x 0.50-inch Phillips pan head screws, supplied). The receiver is one rack unit (1 RU) high.  
DESKTOP MOUNTING  
Install the CM9700UTP Series active receiver on a desktop using the four 8-32 x 0.25-inch Phillips pan head screws (supplied) to attach the  
protective bumpers to the bottom of the unit.  
POWER AND VIDEO CONNECTIONS  
1. Connect the power cord to the unit.  
2. Connect the video input from the UTP cable to the RJ-45 connector on the back of the unit.  
3. Connect the video output from the BNC to a video source.  
CABLE SPECIFICATIONS  
The supplied wire assembly cables are an easy connection option if patch panels are not available. The RJ-45 connector on each wire assembly  
plugs directly into the rear panel of the receiver. The four wire pairs on each wire assembly can be used for individual camera connections. Refer  
to Figure 6 on page 11 for a sample application.  
Always connect the UTP wires on the cable positive to positive (+) and from negative to negative (–). For example, if you connect the blue wire to  
the positive (+) on the active receiver, make sure you connect the other end of the blue wire to the positive (+) on the transmitter. Figure 5 and  
Table A show the RJ-45 UTP pin designations.  
+ - + - + - + -  
Figure 5. RJ-45 Connector Pins  
Table A shows the RJ-45 connector pin assignments.  
Table A. RJ-45 Pin Designations  
Pin  
1
2
3
4
5
6
7
8
Signal  
Input 1 +  
Input 1 –  
Input 2 +  
Input 3 –  
Input 3 +  
Input 2 –  
Input 4 +  
Input 4 –  
Color  
White/Orange  
Orange  
White/Green  
Blue  
White/Blue  
Green  
White/Brown  
Brown  
Video  
Video 1  
Video 1  
Video 2  
Video 3  
Video 3  
Video 2  
Video 4  
Video 4  
10  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
You can connect the active receiver to a transmitter such as the TW4001P passive transceiver, TW3001AT active transmitter, and CC3710/  
CC3610 UTP cameras. The receiver also has video ribbon cable connectors for connecting to a CM9700 Series matrix. Connect these products  
using UTP Cat5e and Cat6 cable for best video performance.  
Table B shows the maximum cable distance for video when connecting an active receiver to a TW4001P passive transceiver.  
Table B. Cable Distance with TW4001P  
Cable  
Type  
Maximum Distance  
(video only)  
Cat5  
Cat5e  
Cat6  
3,000 ft (914 m)  
4,000 ft (1,219 m)  
4,000 ft (1,219 m)  
Table C shows the minimum wire gauge for single wire and stranded wire.  
Table C. Wire Gauge  
Wire Gauge (minimum allowable)  
Single wire (solid)  
Stranded wire  
(flexible)  
24 AWG (0.25 mm2)  
24 AWG (1.0 mm2)  
Figure 6 shows a wire assembly cable (part #WA01-5104-005AG) connecting four cameras to a CM9700UTP32A. Refer to Figure 5 and Table A  
for the RJ-45 pin designations.  
PIN 5 +  
PIN 4 -  
CAMERA 4  
WHITE/BROWN  
CC3610/CC3710  
SERIES CAMERA  
BROWN  
8 PINS (4-/5+)  
10 PINS (5-/6+)  
BLUE  
WIRE = +  
CAMERA 3  
WHITE/BLUE  
BLUE  
GRAY  
= -  
WIRE  
CAMCLOSURE  
CAMERA 2  
VC-UTP  
BOARD  
WHITE/GREEN  
GREEN  
SPECTRA®  
CAMERA 1  
ORANGE  
WHITE/ORANGE  
TW4001P  
FIXED CAMERA  
WIRE  
ASSEMBLY  
CABLE  
1-4  
1-4  
5-8  
9-12  
13-16  
29-32  
1
17  
2
18  
3
19  
4
20  
5
21  
6
22  
7
23  
8
24  
9
25  
10 26  
11 27  
12 28  
13 29  
14 30  
15 31  
16 32  
TO MXB  
17-20  
21-24  
25-28  
100-240 VAC 50-60Hz 75A  
CM9700-UTP32A  
Figure 6. Using the Wire Assembly Cables  
C3646M-C (6/09)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
INSTALLING THE JUMPERS FOR CE COMPLIANCE (ONLY CM9700UTP16A)  
WARNING: To meet CE compliance standards, jumpers must be installed on channels 1 through 16.  
1. Unplug the unit to turn off the power.  
2. Unscrew the six, black 4-40 x 0.25-inch Phillips flat head screws that secure the cover to the chassis.  
3. Remove the cover.  
4. Install the 16 jumpers on the pins; use one for each channel (refer to Figure 7). The pins are labeled J66 through J81.  
6
J 6  
C H 1  
6 7  
J
2
H
C
8
6
J 6 6  
C H 1  
J
C H 3  
9
6
J
J 6 7  
C H 4  
C H 2  
7 0  
J
J 6 8  
C H 5  
1
7
C H 3  
J
C H 6  
J 6 9  
C H 4  
2
7
J
C H 7  
3
J 7 0  
C H 5  
7
J
7 4  
J
C H 8  
C H 9  
7 5  
J
C H 1 0  
7 6  
J
C H 1 1  
7
J 7  
C H 1 2  
8
7
J
C H 1 3  
9
7
J
C H 1 4  
5
1
J 8 0  
C H  
6
J 8 1  
C H 1  
Figure 7. Installing the Jumpers for CE Compliance  
INSTALLING THE JUMPERS FOR CE COMPLIANCE (ONLY CM9700UTP32A)  
If you require jumpers for the 32-channel model (CM9700UTP32A), contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or  
+1-559-292-1981 (international).  
12  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
COLOR VIDEO RANGE SETTINGS  
For optimal tuning, adjust the rotary switch located on the front panel to the correct color video range position. Refer to Figure 8 and Table D, and  
then complete the following steps:  
1. Plug the power cord into a power source to turn on the unit. The LED for the camera input on the front panel turns green if the channel is set  
to the correct color video range. If the color video range is incorrect, the LED turns orange or red.  
NOTE: The color burst signal-to-noise ratio is very low for cable lengths around 4,000 ft (1219 m) and longer, depending on the type of  
cable used. The video activity LED might not indicate the correct video status (for color or black-white). Pelco does not recommend  
operating the unit in an excessive noise environment, where picture quality could be compromised. For information about the color burst  
signal, refer to the Advance Color Video Signal Settings on page 15.  
2. Observe the video on the monitor. If required, turn the rotary switch on the front panel to match the color video range (cable length) of the  
device connected to the receiver. Refer to Figure 8 and Table D for rotary switch positions and cable lengths.  
3. Initial system setup (only): The device automatically adjusts the gain and adapts to the cable length in the range specified by the rotary  
switch; however, during initial installation, if the burst level is lower than a defined threshold, adjustment of the DIP switches may be  
required. To set the DIP switches for color video at initial power-up, complete the following steps:  
a. Unscrew the four thumb screws located on the front panel of the receiver.  
b. Carefully open the front panel until the hinges are completely exposed; the front panel should remain attached to the receiver.  
c. Refer to Table E on page 14 to set the DIP switches to obtain the desired video quality. Refer to Figure 9 on page 14 for the  
arrangement of the DIP switches on the front panel.  
d. Disconnect and reconnect the video input.  
e. If the gain is still insufficient, increase the gain of the DIP switch (refer to Table E on page 14), and then repeat step d.  
8
7
6
5
4
3
2
1
24  
23  
22  
21  
20  
19  
18  
17  
3
2
4
MADE IN USA  
1
3
Figure 8. Factory Default Dial Position (32-channel model shown)  
Table D. Rotary Switch Settings  
Rotary Switch  
Cable Length  
Position  
0 to 1,000 ft (0 to 300 m)  
1
2
3
4
1,000 to 2,000 ft (300 to 600 m)  
2,000 to 3,000 ft (600 to 900 m)  
3,000 to 4,000 ft (900 to 1,200 m)  
NOTES:  
•
•
•
Rotary switch settings are dependent upon the installation, the type of cable used, and the connections made.  
The default setting for the DIP switch is medium gain (refer to Black-White or Day/Night Video Settings on page 14).  
The unit starts in black-white mode. If the gain is incorrectly set for color video, the color burst amplitude may not be adequate (< 70 mV) to  
switch the device to automatic gain control (AGC) mode.  
C3646M-C (6/09)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
BLACK-WHITE OR DAY/NIGHT VIDEO SETTINGS  
For the best picture quality, adjust the DIP switch settings. Refer to Figure 9 and Table E, and then complete the following steps:  
1. Plug the power cord into a power source to turn on the unit. When the input video signal is present, the LED on the front panel glows  
orange. If the video range is incorrect, the LED glows red.  
NOTE: The color burst signal-to-noise ratio is very low for cable lengths around 4,000 ft (1219 m) and longer, depending on the type of  
cable used. The video activity LED might not indicate the correct video status (for color or black-white). Pelco does not recommend  
operating the unit in an excessive noise environment, where picture quality could be compromised. For information about the color burst  
signal, refer to the Advance Color Video Signal Settings on page 15.  
2. Unscrew the four thumb screws located on the front panel of the receiver.  
3. Carefully open the front panel until the hinges are completely exposed. The front panel should remain attached to the receiver.  
4. Refer to Table E to set the DIP switches to obtain the desired video quality. Refer to Figure 9 for the arrangement of the DIP switches on the  
front panel.  
CH 16–9  
CH 8–1  
ON  
ON  
ON  
ON  
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
16  
32  
15  
31  
14  
30  
11  
27  
10  
26  
9
8
1
ON  
1
2
3
4
6
7
8
ON  
1
2
3
5
6
7
8
ON  
1
2
3
4
6
7
8
ON  
1
2
3
5
6
7
8
25  
24  
17  
1
2
ON  
1
2
3
4
6
7
8
ON  
1
2
3
6
7
8
ON  
1
2
3
4
6
7
8
ON  
1
2
3
6
7
8
ON  
ON  
ON  
ON  
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
CH 32–25  
CH 24–17  
Figure 9. DIP Switch Locations with Front Panel Removed (32-channel model shown)  
Table E. DIP Switch Settings  
Left Switch  
Position  
Right Switch  
Position  
Gain  
Low  
Medium  
High  
14  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Configuration  
This section describes an optional advanced tuning procedure for troubleshooting a video path. For most installations, the steps detailed in Color  
Video Range Settings on page 13 should be sufficient to set up the unit.  
Required Equipment  
•
Video signal generator  
•
Oscilloscope  
NOTE: A signal generator and oscilloscope are preferred to perform this procedure, but a video signal from a camera observed on an  
oscilloscope can also be used for this process.  
ADVANCE COLOR VIDEO SIGNAL SETTINGS  
To check the color burst level and set the video signal for optimal output:  
1. From a signal generator or a color camera, send a multiburst color video signal through the UTP to the unit.  
2. Set the rotary switch to the correct position for the cable length (refer to Table D on page 13).  
3. The LED for the camera input on the front panel glows green if video is present. If the color video range is incorrect, the LED glows orange  
or red. Turn the rotary switch on the front panel, beginning at position 1, clockwise until the LED glows green.  
NOTE: If the LED glows green at more than one switch position, set the rotary switch at the lower position; this will ensure  
over-amplification does not occur.  
4. Disconnect and then reconnect the video source. If the LED is green and the color video range on the oscilloscope resembles Figure 10, then  
the gain is sufficient. The color burst and sync closely match the output of the ideal video signal (refer to Figure 11).  
COLOR BURST  
SIGNAL  
SYNC  
SIGNAL  
BURST AND SYNC  
ARE PER SPECIFICATIONS  
Figure 11. Ideal Video Signal  
Figure 10. Color Burst and Sync are per Specifications  
5. If the video signal is out of range, increase the gain by resetting the position of the DIP switches (refer to Table E on page 14).  
6. Repeat steps 4 and 5 until the DIP switches are set to High gain or the LED glows green.  
7. If the video signal is still out of range, turn the rotary switch to the next switch position, and then repeat step 4. Continue to repeat this  
process until the LED glows green, and the color video range on the oscilloscope resembles Figure 10 and Figure 11.  
C3646M-C (6/09)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
ADVANCE BLACK-WHITE VIDEO SIGNAL SETTINGS (DAY/NIGHT CAMERAS)  
Using a video signal generator, complete the following steps to fine tune the black and white signal:  
1. Verify the color video signal (refer to Advance Color Video Signal Settings on page 15).  
2. Send a black-white video signal, from a signal generator or a black-white camera, through the UTP to the unit.  
3. Set the rotary switch to the correct position for the cable length (refer to Table D on page 13). If the cable length is not known, then begin at  
position 1 on the rotary.  
4. The LED for the camera input on the front panel glows orange if black-white video is present.  
5. Turn the rotary switch on the front panel, beginning at position 1, until the video signal on the oscilloscope resembles Figure 12.  
GAIN SET CORRECTLY,  
NO OVERSHOOT  
Figure 12. Ideal Black-White Video Signal  
6. If the video signal is out of range, increase the gain by resetting the position of the DIP switches (refer to Table E on page 14). The optimal  
DIP switch position for black-white video is medium gain (300 meters). A high gain setting will overamplify the signal (refer to Figure 13).  
GAIN IS HIGH  
Figure 13. High Gain Signal  
16  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Maintenance  
For proper ventilation, use the following instructions to maintain the fan filter and fan. For information about the operating temperature range,  
refer to Specifications on page 20.  
FAN FILTER: CLEANING OR REPLACING  
Filters can be cleaned and reused, or they can be replaced. The fan filter should be removed and cleaned as required to ensure proper ventilation  
and cooling of the unit. A clogged fan filter or an ambient operating temperature exceeding 95°F (35°C) will cause the unit’s internal temperature  
to rise above the specified temperature range. When this happens, the Pelco badge LED will flash and an alarm will sound indicating there is an  
alarm condition; however, the fan’s LED indicator will not glow red. If this occurs, replace the fan filter next to the alarm indicator.  
Figure 14. Fan Filter Replacement (32-channel model shown)  
ì 4-40 x 0.25-inch, Phillip flat head screws, black  
î Fan guard  
ï Fan filter (part number FF01-3503-0500)  
To remove a fan filter, refer to Figure 14 and perform the following steps:  
1. Unscrew the two, black 4-40 x 0.25-inch Phillips flat head screws that secure the fan guard to the front panel. Set the screws to the side.  
2. Remove the fan guard. Set the fan guard to the side.  
3. Remove the filter and inspect it for wear and physical damage.  
4. Perform one of the following options:  
a. To clean a filter:  
(1) Do not use compressed air to clean the filter; instead, use a compressed gas duster.  
(2) Reinstall the filter.  
b. To replace a worn or damaged filter, install a new filter.  
5. Reinstall the fan guard and Phillips flat head screws removed in steps 1 and 2.  
C3646M-C (6/09)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
FAN REPLACEMENT  
Fans maintain the unit’s internal temperature within the specified range if the ambient operating temperature is at or below 95°F (35°C). Fans are  
removable and field replaceable. If a fan fails, the Pelco badge LED will flash, an alarm will sound, and the fan’s indicator will glow red indicating  
an alarm condition. If this occurs, replace the fan next to the alarm indicator.  
Figure 15. Fan Replacement (32-channel model shown)  
ì 4-40 x 0.25-inch, Phillip flat head screws, black  
î Fan guard and filter  
r Fan assembly (part number WA01-4744-011D)  
s Fan mount  
ï 4-40 x 1.187-inch, Phillip flat head screws, black  
ñ 4-40 x 0.25-inch, Phillip flat head screws, black  
ó Inner fan grill  
t Front panel bracket  
u Fan wire assembly  
18  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
To replace a fan, refer to Figure 15 and perform the following steps:  
1. Unplug the unit to turn the power off.  
2. Loosen the four thumb screws located on the front panel cover (refer to Figure 16). Pull the front panel away from the chassis, and then let  
it hang from the front panel brackets.  
Figure 16. Remove Front Panel (32-channel model shown)  
3. Unscrew the two, black 4-40 x 0.25-inch Phillips flat head screws that secure the front panel to the front panel bracket.  
4. Unscrew the two, black 4-40 x 0.25-inch Phillips flat head screws that secure the fan guard to the front panel. Remove the fan guard and filter.  
5. Unscrew the two, black 4-40 x 1.187-inch Phillips flat head screws that secure the inner fan grill, fan assembly, and fan mount to the  
front panel.  
6. Remove the installed fan assembly. Disconnect the fan wire assembly from the connector located inside the unit.  
7. Install the new fan, reconnect the fan wire assembly, and then reinstall the fan mount and inner fan grill. Secure with the two, black  
4-40 x 1.187-inch Phillips flat head screws  
8. Reattach the front panel to the unit. Replace the filter and reinstall the fan guard with two, black 4-40 x 0.25-inch Phillips flat head screws.  
C3646M-C (6/09)  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications  
VIDEO  
Video Standards  
NTSC/PAL/EIA/CCIR composite  
Video Output  
CM9700UTP16A  
CM9700UTP32A  
16 BNC and 1 ribbon cable connector  
32 BNC and 2 ribbon cable connectors  
Frequency Response  
50 Hz to 6 MHz  
Common Mode/Differential  
Mode Rejection  
Video Output  
>60 dB  
1.2 Vp-p  
ELECTRICAL  
Input Voltage  
100 to 240 VAC, 50 to 60 Hz, autoranging  
Input Current  
CM9700UTP16A  
CM9700UTP32A  
0.38 A  
0.75 A  
Wire Type  
UTP (24 AWG minimum)  
Cat5, Cat5e, or Cat6  
Wire Category  
Wire Distance  
Cat5  
Cat5e and Cat6  
3,000 ft (914 m)  
4,000 ft (1,219 m)  
DC Loop Resistance  
Differential Capacitance  
Transient Immunity  
20 ohms per 328 ft (100 m)  
6.6 nF/328 ft (100 m) maximum  
300 W peak pulse power (8/20 US)  
24 AWG (0.25 mm2)  
Single Wire (solid)  
Stranded Wire (flexible)  
24 AWG (1.0 mm2)  
MECHANICAL  
Connectors  
BNC  
Ribbon Cable Connector  
RJ-45  
Video output  
Video output  
UTP input  
Power Connector  
IEC connector  
Construction  
Finish  
Steel chassis, aluminum front panel  
Black matte finish  
20  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
FRONT PANEL INDICATORS/FUNCTIONS  
LED Indicators  
16 or 32 video status LEDs (depending on the model), 3 fan status LEDs, and Pelco badge power status  
Pelco Badge  
Power  
Temperature and Fan Status  
Alarm Status  
Video Status  
Blue  
Flashes blue  
Audible  
Green, red, orange  
Red  
Fan Alarm  
ENVIRONMENTAL  
Operating Temperature  
32° to 95°F (0° to 35°C) at unit air intake  
0 to 90%, noncondensing  
Relative Humidity  
NOTE: The temperature at the unit air intake can be significantly higher than room temperature. Temperature is affected by rack configuration,  
floor layout, air conditioning strategy, and other issues. To prevent performance failure and unit damage, make sure the temperature at the unit is  
continuously within the operating temperature range.  
PHYSICAL  
Dimensions  
9.00" D x 18.80" W x 1.72" H  
(23.00 x 47.80 x 4.37 cm)  
Unit Weight (approximate)  
CM9700UTP16A  
CM9700UTP32A  
8.10 lb (3.68 kg)  
9.25 lb (4.19 kg)  
C3646M-C (6/09)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
C3646M-C (6/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to a Pelco designated location. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Exceptions to this warranty are as noted below:  
• Five years:  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelco’s liability  
for any claim, whether based on breach of contract, negligence, infringement of  
any rights of any party or product liability, relating to the Products shall not exceed  
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be  
liable for any special, incidental, or consequential damages (including loss of use,  
loss of profit, and claims of third parties) however caused, whether by the  
negligence of Pelco or otherwise.  
–
–
–
Fiber optic products  
TW3000 Series unshielded twisted pair (UTP) transmission products  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models  
• Three years:  
–
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,  
C10CH Series, IP3701H Series, and IX Series)  
EH1500 Series enclosures  
Spectra® IV products (including Spectra IV IP)  
Camclosure® Series (IS, ICS, IP) integrated camera systems  
–
–
–
–
The above warranty provides the Dealer with specific legal rights. The Dealer may  
also have additional rights, which are subject to variation from state to state.  
DX Series digital video recorders, DVR5100 Series digital video recorders,  
Digital Sentry® Series hardware products, DVX Series digital video  
recorders, and NVR300 Series network video recorders  
Endura® Series distributed network-based video products  
Genex® Series products (multiplexers, server, and keyboard)  
PMCL200/300/400 Series LCD monitors  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the  
following information:  
–
–
–
1. Model and serial number  
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number  
3. Details of the defect or problem  
• Two years:  
If there is a dispute regarding the warranty of a product that does not fall under  
the warranty conditions stated above, please include a written explanation with  
the product when returned.  
–
–
–
–
Standard varifocal, fixed focal, and motorized zoom lenses  
DF5/DF8 Series fixed dome products  
Legacy® Series integrated positioning systems  
Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20  
scanners, including when used in continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which the  
item was received by Pelco.  
–
–
–
–
Esprit Ti and TI2500 Series thermal imaging products  
Esprit and WW5700 Series window wiper (excluding wiper blades).  
CM6700/CM6800/CM9700 Series matrix  
RETURNS  
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100  
or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair) and designated return location.  
Digital Light Processing (DLP®) displays (except lamp and color wheel). The  
lamp and color wheel will be covered for a period of 90 days. The air filter is  
not covered under warranty.  
Intelli-M® eIDC controllers  
All merchandise returned for credit may be subject to a 20 percent restocking and  
refurbishing charge.  
–
• One year:  
Video cassette recorders (VCRs), except video heads. Video heads will be  
covered for a period of six months.  
• Six months:  
All pan and tilts, scanners, or preset lenses used in continuous motion  
applications (preset scan, tour, and auto scan modes).  
–
Goods returned for repair or credit should be clearly identified with the assigned  
CA or RA number and freight should be prepaid.  
–
12-23-08  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
C3646M  
Date  
9/08  
Comments  
Original version.  
C3646M-A  
11/08  
Replaced product photo on front cover, added parts list, and revised maintenance section. Also revised the frequency response data, and added the shipping weight  
and single/stranded wire information to the specifications section.  
C3646M-B  
C3646M-C  
1/09  
6/09  
Removed the SECAM video standard from the specifications section.  
Revised manual to include both the 16-channel and 32-channel units.  
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.  
Spectra III is a trademark of Pelco, Inc.  
© Copyright 2009, Pelco, Inc. All rights reserved.  
DLP is a registered trademark of Texas Instruments Incorporated.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
www.pelco.com  
Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA  
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150  
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco TV Mount MM1000 User Manual
Pelonis Fan FT30 A4 User Manual
Pentair Swimming Pool Pump WhisperFlo User Manual
Philips Flat Panel Television 15PF9936 User Manual
Philips TV Cables SWA2427 User Manual
Planar Car Video System pl150m User Manual
Planar Computer Monitor PL170M User Manual
Pride Mobility Mobility Aid INFMANJ2828 User Manual
ProForm Treadmill 831246460 User Manual
PYLE Audio MP3 Player PWMA820 User Manual