DVD RECEIVER
XV-HTD1
SPEAKER SYSTEM
S-HTD1
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS ON YOUR PURCHASE OF THIS FINE PIONEER PRODUCT.
Pioneer is on the leading edge of DVD research for consumer products and this unit incorporates the latest technological
developments. We are sure you will be fully satisfied with the DVD player. Thank you for your support.
Thank you for buying this Pioneer product.
Please read through these operating instructions so
you will know how to operate your model properly.
After you have finished reading the instructions, put
them away in a safe place for future reference.
In some countries or regions, the shape of the power
plug and power outlet may sometimes differ from
that shown in the explanatory drawings. However,
the method of connecting and operating the unit is
the same.
LINE VOLTAGE SELECTOR SWITCH
Only multi-voltage model is provided with this
switch.
Mains voltages in Saudi Arabia are 127 V and
220 V only. Never use this model with the 110 V
setting in Saudi Arabia.
H019 En
The line voltage selector switch is located on the rear panel.
Checkthatitissetproperlybeforepluggingthepowercordinto
the outlet. If the voltage is not properly set or if you move to an
area where the voltage requirements differ, adjust the selector
switch as follows:
¶
Be sure to disconnect the power cord from its outlet before
making this adjustment.
Please read through these operating instructions so
you will know how to operate your model properly.
After you have finished reading the instructions, put
them away in a safe place for future reference.
¶
Use a medium-sized (flat blade) screwdriver. Insert the tip
ofthescrewdriverintothegrooveoftheselectorswitchand
turn it so that the power voltage marking of your area points
to the arrow.
• This player is not suitable for commercial use.
VOLTAGE
SELECTOR
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
240V
220-230V
110-127V
CAUTION 220 – 230 V
Power source voltage is factory adjusted 220 - 230 volts.
If your area is different, change voltage selectors set-
tings.
H038 En
3
En
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Before You Start
Features
What’s in the box
Confirm that the following accessories are in the box
when you open it.
•
•
Superlative audio performance with
Dolby Digital* and DTS** software
The XV–HTD1 delivers breathtaking sound quality with
Dolby Digital and DTS discs.
• Remote control
• AA/R6P dry cell batteries x2
• AM loop antenna
Graphical Setup Navigator
• FM antenna
Setting up your home theater is easy using the
graphical Setup Navigator. Answer the questions that
appear on-screen and the Setup Navigator makes the
necessary video and language settings for you.
• Video cord (yellow)
• Power cord x1 (x2 (Central and South America
models only))
• These operating instructions
• Warranty card (European and Australian models
only)
• This product incorporates copyright protection
technology that is protected by method claims of
certain U. S. patents and other intellectual property
rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protec-
tion technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
• Speaker cords 5m x2 (for front L-R speakers)
• Speaker cord 2m x1 (for center speaker)
• Speaker cords 6m x2 (for rear L-R speakers)
• Speaker cord 3m x1 (for subwoofer)
• Power plug adapter (Central and South America
models only)
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Using this manual
This manual is for the XV–HTD1 DVD Receiver. It is
divided into several sections: system basics and
connecting up (chapters 1 and 2); an explanation of
the controls and displays (chapter 3); setting up for
surround sound and other preferences (chapter 4);
getting started (chapter 5); advanced features (chapters
6–10); system settings and preferences (chapter 11).
* Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories. Confidential
unpublished works. © 1992-1997 Dolby Laborato-
ries. All rights reserved.
** “DTS” and “DTS Digital Surround” are
registered trademarks of Digital Theater Systems,
Inc.
4
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Contents
1
6 Using Surround Sound
Adjusting the bass and treble
Using P.Bass
Using sound modes
Listening to surround-sound
sources
Listening to other sources with
room effects
11 DVD Setup Menu
23 Using the DVD Setup menu
23 Video settings
1 Before You Start
Features
What’s in the box
Using this manual
Putting the batteries in
the remote control
Using the remote control
Hints on installation
Avoiding problems with
condensation
Moving the system
Discs compatible with this system
DVD Video regions
38
38
38
38
39
39
39
39
39
39
40
40
40
41
41
41
41
41
42
4
4
4
23
TV Screen
Picture Quality
S-Video Out
Still Picture
On Screen Display
Angle Indicator
23
6
6
6
24
24
Adjusting the effect level
Listening at low volume
Direct recording
25 Language settings
7
7
7
7
25
OSD language
Audio Language
Subtitle Language
Auto Language
DVD Language
Subtitle Display
Subtitle Off
General settings
Setup Menu Mode
Parental Lock
7 Playing Discs
Introduction
Finding what you want on a disc
Switching camera angles
Switching subtitles
Switching audio language
Switching audio channel
Making a program list
More programming options
Using random play
26
26
26
26
26
26
27
28
28
28
29
29
29
2 Connecting Up
Connecting the speakers
Placing the speakers
Wall mounting the rear speaker
system
Connecting to your TV
Setting the TV System
Connecting the supplied antennas 11
AM loop antenna
FM wire antenna
Connecting external antennas
External AM antenna
External FM antenna
Connecting other components
Connecting the power
8
9
9
10
10
Changing the parental lock level 42
Changing your password
Screen Saver
Background Color
42
43
43
Using repeat play
11
11
12
12
12
13
13
Looping a section of a disc
Playing CDs only (CD Mode)
Bookmarking a place in a disc
Memorizing disc settings
Displaying disc information
Singing karaoke (Except European
model)
12 Additional Information
30 Switching the AM frequency
30
interval
Setting the display brightness
44
44
44
44
45
45
45
45
45
46
47
48
50
51
31 Switching the time format
Resetting the system
3 Controls & Displays
Taking care of your system
Disc lens cleaner
Taking care of your discs
Storing discs
Discs to avoid
Glossary
Language code list
Troubleshooting
Screen sizes and disc formats
Specifications
8 Using RDS (European
model only)
Using RDS
RDS Program types
Displaying RDS information
Remote control
Front panel
Display
14
15
15
32
32
33
4 Setting Up
Switching on and setting the clock 16
Setting up for surround sound
Setting the speaker distances
Balancing the surround sound
Using the Setup Navigator
Searching for a program type
33
16
16
17
18
9 Using the Timer
Using the wake up timer
Activating/deactivating the
wake up timer
34
Switching the demo mode on/off 52
34
35
35
5 Getting Started
Checking the timer settings
Playing DVDs, CDs and Video CDs 19 Using the sleep timer
Basic playback controls
Navigating DVD disc menus
Navigating Video CD PBC menus 20
Exchanging discs
Listening to the radio
Improving FM stereo sound
Saving station presets
19
20
10 Advanced Sound Setup
Advanced sound settings
LFE attenuator
Dynamic Range Control
Dual-mono setting
36
36
36
37
21
21
22
22
22
22
Adjusting channel volume levels 37
Listening to station presets
Listening to other components
5
En
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Before You Start
Chapter 12 provides additional information, including a
glossary of terms used in this manual, and a trouble-
shooting section.
• When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country or area.
Using the remote control
Keep in mind the following when using the remote
control:
Putting the batteries in the remote
control
1 Open the battery compartment cover on
the back of the remote control.
• Make sure that there are no obstacles between the
remote control and the remote sensor on the unit.
• Use within 7 meters of the remote sensor and at an
angle of less than 30º.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
2 Insert two AA/R6P batteries into the
battery compartment following the
indications (ª, ·) inside the
compartment.
• Remote controllers for different devices can interfere
with each other. Avoid using remotes for other equip-
ment located nearby this unit.
• Replace the batteries when you notice the operating
range of the remote starts to decrease.
Hints on installation
We want you to enjoy using this unit for years to come,
so please bear in mind the following points when
choosing a suitable location for it:
3 Close the cover.
Do...
ꢀ Use in a well-ventilated room.
ꢀ Place on a solid, flat, level surface, such as a table,
shelf or stereo rack.
Don’t...
• Remove the batteries if the remote is not going to be
used for a month or more.
✗ Use in a place exposed to high temperatures or
humidity, including near radiators and other heat-
generating appliances.
• Remove dead batteries promptly—they can leak and
damage the unit.
✗ Place on a window sill or other place where the
system will be exposed to direct sunlight.
✗ Use in an excessively dusty or damp environment.
✗ Place directly on top of an amplifier, or other
component in your stereo system that becomes hot in
use.
6
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
1
✗ Use near a television or monitor as you may
experience interference—especially if the television
uses an indoor antenna.
✗ Use in a kitchen or other room where the system
may be exposed to smoke or steam.
Audio CD compatibility:
• 12cm or 8cm (5” or 3”) discs
✗ Use on a thick rug or carpet, or cover with cloth—
• Linear PCM digital audio
this may prevent proper cooling of the unit.
• CD-Audio, CD-R* and CD-RW* formats
CDs are divided into tracks.
✗ Place on an unstable surface, or one that is not large
enough to support all four of the unit’s feet.
* This system can play CD-R and CD-RW discs
recorded with audio. However, depending on the
condition of the player and the disc, you may find that
not all discs will play successfully. (For example, if the
disc is scratched or dirty, or if the player’s pickup lens is
dirty.) Note that this unit cannot record onto recordable
discs.
Avoiding problems with condensation
Condensation may form inside the system if it is
brought into a warm room from outside, or if the
temperature of the room rises quickly. Although the
condensation won’t damage the system, it may
temporarily impair its performance. For this reason you
should leave it to adjust to the warmer temperature for
about an hour before switching on and using.
Video CD compatibility:
• 12cm or 8cm (5” or 3”) discs
Moving the system
• MPEG-1 digital audio
If you need to move the system, first switch it off and
unplug from the wall outlet. Never lift or move the unit
during playback—discs rotate at a high speed and may
be damaged.
• MPEG-1 digital video
Video CDs are divided into tracks.
DVD Video regions
Discs compatible with this system
Any disc that displays one of the following logos should
play in this system. Other formats, including DVD-RAM,
DVD-ROM, DVD-Audio, CD-ROM, SACD and Photo CD
will not play.
ALL
2
3
4
All DVD Video discs carry a region mark on the case
somewhere that indicates which region(s) of the world
the disc is compatible with. Your DVD system also has a
region mark, which you can find on the rear panel.
Discs from incompatible regions will not play in this
system. Discs marked ALL will play in any player.
DVD Video compatibility:
• Single-sided or double-sided discs
• Single layer or dual layer discs
• Dolby Digital, DTS, MPEG or Linear PCM digital
audio
• MPEG-2 digital video
DVD discs are generally divided into one or more titles.
Titles may be further subdivided into chapters.
7
En
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connecting Up
Before making or changing any rear panel connections,
make sure that all the components are switched off and
unplugged from the power supply.
Center
Connecting the speakers
Subwoofer
FRONT
REAR
L
L
L
N
R
AC INLET
R
R
ANTENNA
H
AM
I
LOOP
ANTENNA
FM
U75NΩBAL
SUB-
CENTER
WOOFER
SPEAKERS
Front R
Rear R
Front L
Rear L
The speaker terminal tabs and supplied speaker cables
are color-coded for simpler connection.
1 Twist off the protective covers on the
ends of the speaker
cable.
1 Use the speaker cables with the red
sleeves to connect the front speakers to
the FRONT L and FRONT R terminals.
2 Press the speaker terminal tabs to open
and insert the wire with the colored
sleeve into the colored terminal and the
other wire into the black terminal.
2 Use the speaker cables with the blue
sleeves to connect the rear speakers to
the REAR L and REAR R terminals.
3 Release the speaker terminal tabs to
secure the
3 Use the speaker cable with the grey
sleeves to connect the subwoofer to the
SUBWOOFER terminals.
Colored tab
speaker cable.
Colored
sleeve
4 Use the speaker cable with the green
sleeves to connect the center speaker to
the CENTER terminals.
Black tab
For proper sound, it’s important to connect the positive
(colored) and negative (black) terminals for each
speaker correctly.
4 Connect the other end of the cable to the
speaker in the same way.
Colored sleeve
Black tab
Colored tab
8
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Up
2
The front and center speakers supplied with this system
are magnetically shielded. However, placing them
extremely close to a television may result in color
distortion on the screen. If this happens, move the
speakers a little further away and switch off the
television for 15–30 minutes.
Do not connect any of the supplied speakers to any
other amplifier. This may result in malfunction or fire.
This DVD receiver has been designed for best perfor-
mance when connected to the supplied speakers. We do
not, therefore, recommend that you connect and use
other speakers with this system.
The rear speakers and subwoofer are not magnetically
shielded, so they should not be placed near a TV or
monitor.
Placing the speakers
Where you put your speakers in the room has a big
effect on the quality of the sound. The following
guidelines should help you to get the best sound from
your system.
Wall mounting the rear speaker system
Before mounting
• The subwoofer can be placed on the floor. Ideally, the
other speakers should be at about ear-level when you’re
listening to them. Putting the speakers on the floor
(except the subwoofer), or mounting them very high on
a wall is not recommended.
• Remember that this speaker system is heavy and that
its weight may cause the wood screw to work loose or
the wall to fail to support it, in which case the speaker
system may fall on the floor. This is extremely danger-
ous. Make absolutely sure that the wall is sturdy enough
to support the weight of the speaker system. Do not
mount it on plywood boards or soft-surface walls. The
mounting screws are not included with this unit.
Please find the correct screws for your application.
• For the best stereo effect, place the front speakers 2–
3m apart.
• The rear speakers should not be further away from
your listening position than the front speakers.
• The center speaker should be as close as possible to
Wall-mounting bracket
the TV screen so that movie dialog is localized properly.
3.5 mm
9.5 mm
2-3 meters
Center TV
Front L
Front R
Wood screw
Subwoofer
Rear L
Rear R
Protrude:5-7mm
Your listening position
• If you are unsure of the qualities and strength of the
walls, consult a professional for advice.
• PIONEER is not responsible for any accidents or
damage that result from improper installation.
If you install the center speaker on top of your TV, be
sure to secure it with tape or by some other suitable
means. An unsecured speaker may fall from the TV due
to external shocks such as earthquakes, endangering
those nearby or damaging the speaker.
9
En
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connecting Up
Connecting to your TV
FRONT
L
COAX
DIGITAL
R
R
IN
TV/
VCR
AC INLET
VOLTAGE
SELECTOR
SUB-
WOOFER
IN
IN
240V
220-
I
230V
110-
H
VIDEO
OUT
127V
AM
LOOP
Supplied video cord
ANTENNA
FM
U75NΩBAL
AUX
1
S-VIDEO
OUT
OUT
VIDEO
IN
S-VIDEO
IN
S-Video cord (not supplied)
1 Use the supplied yellow video cord to
connect the VIDEO OUT jack to a video
input on your TV.
Setting the TV System
The default setting of this player is AUTO, and unless
you notice that the picture is distorted when playing
some discs, you should leave it set to AUTO.
Alternatively, you can use an S-Video cable (not
supplied) to connect the S-VIDEO OUT jack to an S-
Video input on your TV. S-Video should give you better
picture quality than using the standard VIDEO OUT.
If you experience picture distortion with some discs, set
the TV system to match your country or region.
1 Make sure that the system is in standby.
• See S-Video Out on page 39 for how to change the
S-Video setting between S1 and S2 format.
2 Press SYSTEM SETUP.
The current TV system is shown in the display.
2 Optionally: Use a stereo audio cord to
connect the audio outs of your TV (or
VCR) to the TV/VCR IN jacks.
This will enable you to hear the TV (or VCR) sound
through this system.
3 Use 5 or ∞ to change the TV system.
Switch between auto, ntsc and pal.
4 Press ENTER.
The system returns to standby power.
• If you want to connect both your TV and VCR, use
the TV/VCR IN jacks for one and the AUX IN jacks for
the other.
Placing the main unit too close to your TV may cause
interference, especially if you’re using an indoor
antenna. If you notice interference, move the unit away
from the TV.
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Up
2
AM loop antenna
Connecting the supplied antennas
1 Pull off the protective shields of both AM
antenna wires.
European model
FM wire
antenna
2 Press the antenna terminal tabs to open
and insert one wire into each terminal.
AM loop antenna
3 Release the tabs to secure the AM an-
tenna wires.
FRONT
REAR
ANTENNA
L
L
L
R
R
R
H
SUB-
WOOFER
CENTER
AM
SPEAKERS
COAX
LOOP
-
DIGITAL
IN
ANTENNA
TV/
VCR
4 Bend the stand in the direction indicated
by the arrow (see fig. A below left).
VIDEO
OUT
AUX
S-VIDEO
OUT
O
FM
U75NΩBAL
5 Clip the loop onto the stand (fig. B below
left).
Except European model
6 Place the AM antenna on a flat surface
and point in the direction giving the best
reception.
FM wire
antenna
AM loop antenna
Avoid placing near computers, television sets or other
electrical appliances and do not let it come into contact
with metal objects.
FRONT
REAR
ANTENNA
L
L
L
R
R
R
H
SUB-
WOOFER
CENTER
AM
SPEAKERS
COAX
LOOP
-
DIGITAL
IN
ANTENNA
It’s also possible to fix the AM antenna to a wall. When
installing on a wall or other surface, perform steps 4
and 5 after first securing the stand with screws (see fig.
C below left). Before fixing, make sure that the
reception is satisfactory.
TV/
VCR
I
VIDEO
OUT
AUX
S-VIDEO
OUT
FM
U75NΩBAL
H
The supplied antennas provide a simple way to listen to
AM and FM radio. If you find that reception quality is
poor, an outdoor antenna should give you better sound
quality—see Connecting external antennas on page
12 for more on how to do this.
FM wire antenna
•
Connect the FM wire antenna to the FM
UNBAL 75Ω terminals in the same way as
the AM loop antenna.
For best results, extend the FM antenna fully and fix to
a wall or door frame. Don’t drape loosely or leave coiled
up.
fig. A
fig. B
fig. C
The signal earth (H) is designed to reduce noise that
occurs when an antenna is connected. It is not an
electrical safety earth.
11
En
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connecting Up
Connecting external antennas
External AM antenna
Use 5–6 meters of vinyl-insulated wire and set up either
indoors or outdoors. Leave the supplied AM loop
antenna connected.
External FM antenna
Except European model : Use 75Ω coaxial cable to
hook up an external FM antenna. Do not leave the
supplied FM wire antenna attached.
European model : Use 75Ω coaxial cable with a PAL
connector to hook up an external FM antenna.
European model
Outdoor
AM antenna
Indoor
AM antenna
H
AM
LOOP
ANTENNA
FM
U75NΩBAL
PAL connector
Except European model
Outdoor
AM antenna
Indoor
AM antenna
H
AM
LOOP
ANTENNA
FM
U75NΩBAL
H
75 Ω coaxial cable
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Up
2
Connecting other components
FRONT
REAR
OAX
L
L
L
R
L
R
R
TV/
VCR
AC INLET
VOLTAGE
IN
SELECTOR
SUB-
WOOFER
240V
SPEAKERS
220-
230V
110-
127V
L
IN
AUX
OUT
Tape deck, VCR,
MD recorder, etc.
OUT (PLAY)
Analog
IN (REC)
1 Use a stereo audio cable to connect the
Connecting the power
AUX IN jacks to the analog outputs of an
external component.
Before connecting the power and switching on for the
first time make sure that everything is connected
properly (See page 3).
This will allow you to play the component through this
system.
1 Plug one end of the supplied power cord
into the AC INLET.
2 Use a stereo audio cable to connect the
AUX OUT jacks to the analog inputs of an
external component.
2 Plug the other end into a household
power outlet.
This will allow you to record from this system to an
external tape/MD/CD recorder.
3 Use a digital coaxial cable to connect the
DIGITAL IN COAX jack to the digital
output of an external component.
This will allow you to play a digital audio component
(MD player, etc.) through this system.
FRONT
REAR
L
L
L
R
R
R
SUB-
WOOFER
CENTER
SPEAKERS
COAX
R
L
-
DIGITAL
IN
TV/
VCR
IN
IN
-
VIDEO
OUT
AUX
AC INLET
S-VIDEO
OUT
OUT
H
VOLTAGE
SE ECTOR
The DIGITAL IN COAX jack should only be connected
to a PCM audio output (32, 44.1 or 48kHz). These
include CD, MD and DAT players and satellite receivers.
Check the instructions that came with your other
component for more details.
13
En
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Controls & Displays
15 ENTER
16 Cursor right Use for navigating menus and on-screen
Remote control
displays.
17 MENU Page 20
TOP MENU Page 20
18 Cursor down Use for navigating menus and on-screen
displays.
DVD
/CD
TUNER
/BAND
TV
STANDBY
/ON
/AUX
1
5
2
6
3
7
4
8
TEST TONE SURROUND
CH LEVEL
MODE
MUTE
DSP
19 SOUND Page 24, 25
20 7 Page 19
21 3/8 Page 19
VOLUME
—
DVD SETUP
+
9
10
SYSTEM SETUP
5
12
15
18
21
11
13
ENTER
2
3
14
16
TOP MENU
MENU
22 RETURN
Page 20
SOUND
∞
17
19
23 4 / –PREV Pages 19-20
24 1 / STEP/SLOW e Pages 19-20
25 ¡ / STEP/SLOW E Pages 19-20
26 ¢ / NEXT+ Pages 19-20
27 1 / CONDITION (SHIFT & 1) Page 30
28 2 / LAST MEMO (SHIFT & 2) Page 29
29 3 / SEARCH (SHIFT & 3) Page 26
30 CLEAR Clears/cancels various functions
DVD DISP (SHIFT & CLEAR) Page 30
31 4 / ANGLE (SHIFT & 4) Page 26
32 5 / MONO (SHIFT & 5) Page 22
33 6 / SLEEP (SHIFT & 6) Page 35
34 >10 Selects numbers over 10 Page 20
FL DIMMER (SHIFT & >10) Page 44
35 7 / PROGRAM (SHIFT & 7) Page 28
36 8 / RANDOM (SHIFT & 8) Page 28
37 9 / REPEAT (SHIFT & 9) Page 28
38 REP A–B (SHIFT & 10/0) Page 29
10/0 Number button (10 and 0)
RETURN
7
6
20
23
22
26
— PREV
e
STEP/SLOW
E
NEXT +
4
1
¡
¢
24
28
32
36
40
44
48
25
29
33
37
41
45
49
CONDITION LAST MEMO
SEARCH
DVD DISP
CLEAR
1
ANGLE
2
3
27
31
35
39
43
47
30
34
38
42
46
50
MONO
SLEEP
FL DIMMER
4
5
6
>10
REP A—B
PROGRAM
RANDOM
REPEAT
7
8
9
10/0
CD MODE
AUDIO
SUBTITLE SYSTEM DISP
DISC
1
DISC
DISC
2
4
DISC
DISC
3
5
DISC SKIP
OPEN/
SHIFT
CLOSE
0
1
2
3
4
5
6
7
8
9
DVD/CD Pages 19, 34
TUNER/BAND Pages 21-22, 34
TV/AUX Pages 22, 34
STANDBY/ON Page 19
MUTE Silences/restores all sound.
TEST TONE/CH LEVEL Page 17
SURROUND MODE Pages 17, 24
DSP Page 24
39 CD MODE Page 29
40 AUDIO Page 26
41 SUBTITLE Page 26
42 SYSTEM DISP Page 16
43 DISC 1 Page 20
44 DISC 2 Page 20
45 DISC 3 Page 20
46 DISC SKIP Pages 19, 21
VOLUME – Lowers the volume.
10 VOLUME + Raises the volume.
11 DVD SETUP Pages 18, 38
47 SHIFT Hold down to access secondary button functions
48 DISC 4 Page 20
12 Cursor up Use for navigating menus and on-screen
displays.
49 DISC 5 Page 20
50 OPEN/CLOSE 0 Pages 19, 21
13 SYSTEM SETUP Pages 16, 22, 34-37, 44
14 Cursor left Use for navigating menus and on-screen
displays.
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Displays
3
This illustration is not European model.
Front panel
1
2
3
4
5
6
7
DISC SKIP EXCHANGE
0
OPEN/CLOSE
1
2
3
4
5
VIDEO
VOLUME
DVD RECEIVER XV-HTD1
STANDBY/ON
STANDBY
CD
MODE
ADVANCED
THEATER
DSP
DISC
1
2
3
4
5
Karaoke
1
.
.
¢
DVD/CD
TUNER/BAND
TV/AUX
CD MODE
7
3/8
4
1
¡
MIC
LEVEL
MIC
PHONES
20
19
18
17
16
15
14
13
12 11
10
9
8
1
STANDBY indicator
CD MODE indicator
9
Mic input (Except European model)
10 Mic volume (Except European model)
11 DISC indicators
ADVANCED THEATER indicator
DSP indicator
Disc tray
12 ¡ • ¢ Pages 19-20
13 4 • 1 Pages 19-20
14 6 Page 19
15 7 Page 19
16 CD MODE Page 29
17 TV/AUX (/DIGITAL IN) Pages 22, 34
18 TUNER/BAND Pages 21-22
19 DVD/CD Pages 19, 34
20 STANDBY/ON Page 19
2
3
4
5
6
7
8
Disc buttons Page 20
DISC SKIP Pages 19, 21
EXCHANGE Page 21
0 OPEN/CLOSE Pages 19, 21
VOLUME Turn to adjust the volume.
PHONES Plug in a pair of headphones here.
Display
1
2
3
4
5
6
7
8
9
10
11
12
13
MIDNIGHT CONDITION ANGLE LAST MEMO
2
DIGITAL
2
PRO LOGIC
L
C
LFE
S
R
ALL DISCS
RANDOM
REPEAT
Ls
Rs
18 17 16
15
14
1
2
3
4
5
6
7
8
9
DTS pages 23, 46
2 DIGITAL pages 23, 46
2 PRO LOGIC page 23
11 CONDITION page 30
12 ANGLE page 26
13 LAST MEMO page 29
14 Channel indicators Show which channels are available
on the current disc.
15 Character display When playing discs : Left to right
displays disc number, title, chapter/track, minutes, seconds.
16 RANDOM page 28
Timer indicator page 34
Sleep indicator page 35
Tuned indicator page 21-22
FM stereo indicator page 22
FM mono indicator page 22
RDS (European model only) Lights when in one of
17 REPEAT page 28
the RDS display or search modes
10 MIDNIGHT page 25
18 DISC | ALL DISCS Indicates the random or repeat
mode; page 28–29
15
En
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Setting Up
Switching on and setting the clock
This system has a built-in clock, which needs to be set
to be able to use the timer features.
Setting up for surround sound
You can use this system right out of the box for
surround sound with just the default settings. However,
for really great surround sound, we recommend that
you spend a few minutes making some settings that
match this system to your listening room. Unless you
change the layout of your speakers or main listening
position, you only need to make most of these settings
once.
STANDBY
/ON
SYSTEM SETUP
5
ENTER
2
3
∞
TEST TONE SURROUND
/CH LEVEL
MODE
SYSTEM DISP
VOLUME
–
+
SYSTEM SETUP
5
ENTER
2
3
∞
SHIFT
1 Press to switch on.
2 Press SYSTEM SETUP.
3 Press the 2 or 3 button until you see
TIMER in the display.
4 Press ENTER.
Setting the speaker distances
1 Press SYSTEM SETUP.
5 Press 2 or 3 until you see CLOCK ADJ in
the display.
6 Press ENTER.
The display shows a clock, with the hour blinking.
2 Press the 2 or 3 button until you see
FRT. SP in the display.
7 Use the 5 and ∞ buttons to set the hour,
then press ENTER.
3 Use the 5 and ∞ buttons to set the
distance from your main listening posi-
tion to the front speakers.
8 Use the 5 and ∞ buttons to set the
minute, then press ENTER.
Ideally, your listening position should be equidistant
from the two front speakers.
The display blinks to indicate that the time has been set.
The default setting is 3m. You can adjust the range
from 0.3m to 9.0m in steps of 0.3m.
• Press SYSTEM DISP anytime to see the clock when
the system is on or in standby.
16
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
4
4 Press 3 to move on to the CENTER
speaker setting.
It may not be possible to accurately adjust the
subwoofer level using this method. You may prefer to
leave it on its default setting and adjust it to your liking
later when playing surround-sound sources.
5 Use the 5 and ∞ buttons to set the
distance from your main listening posi-
tion to the center speaker.
The default setting is 3m. You can adjust the range
from 0.3m to 9.0m in steps of 0.3m.
• You cannot change the DSP mode when Record
mode is active (see Direct recording on page 25).
6 Press 3 to move on to the SURROUND
speakers setting.
1 Press SURROUND MODE.
The surround mode can be set to anything except
SURROUND OFF or AUTO (No test tone is output in
these modes.)
7 Use the 5 and ∞ buttons to set the
distance from your main listening posi-
tion to the surround speakers.
2 Set the volume to a moderate level.
Ideally, your listening position should be equidistant
from the surround speakers.
3 Press TEST TONE (SHIFT & CH LEVEL) to
start the test tone then adjust the volume
to a suitable level.
The default setting is 3m. You can adjust the range
from 0.3m to 9.0m in steps of 0.3m.
The test tone plays through each speaker in turn:
8 Press ENTER to exit.
• Front left
• The setting mode is automatically exited if no
operation is performed within 20 seconds.
• Center
• Front right
• Surround right
• Surround left
• Subwoofer
• There are several other settings that you can make
from the System Setup menu to further tailor your
surround sound. See chapter 9 for more on this.
• The speaker distance settings have no effect when the
surround mode is set to VIR.SURR.1 or VIR.SURR.2.
See page 23 for more on surround modes.
4 Use the 5 and ∞ buttons to adjust the
level of a speaker as the test tone plays.
For best results, sit in your main listening position when
doing this. You can adjust each speaker in the range of
+/-10dB.
You can’t make these settings with the Record mode on.
See page 25 for how to switch the Record mode on/off.
5 When you're done, press TEST TONE
(SHIFT & CH LEVEL) to turn off the test
tone.
Balancing the surround sound
You can further improve surround sound performance
by balancing the levels from the subwoofer, center and
surround speakers relative to the front left/right
speakers. To help you judge the sound level of each
speaker a test tone is played through each speaker in
turn (make sure that there are no headphones
connected). Adjust the levels until they all sound equal.
The levels you set here will apply to all surround modes.
However, you can set levels independently for each DSP
mode.
17
En
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Setting Up
3 Select START.
Using the Setup Navigator
• If you decide not to use the Setup Navigator, select
Auto Start Off here instead.
Before playing any discs, we strongly recommend using
the Setup Navigator. This makes all the basic DVD
system settings for you.
4 Choose an OSD menu language.
Video Language General
Setup Navigator
Language
English
OSD Language français
Español
Select the On Screen Language
ENTER
SETUP
Exit
Move
Select
DVD SETUP
5
ENTER
2
3
∞
7
• The language options shown in the on-screen
display illustrations on the following pages may not
correspond to those available in your country or region.
5 Select the type of TV you have.
Video Language General
Setup Navigator
TV Connection
TV Type
Widescreen (16:9)
Standard (4:3)
Widescreen TV
16:9 aspect ratio
ENTER
SETUP
Exit
Move
Select
• See Aspect ratio in the glossary on page 46 if you’re
unsure of the difference between widescreen and
standard TVs.
1 Make sure that the system is switched on.
Also turn on your TV and make sure that it is set to the
correct video input.
• If a disc that’s already loaded starts to play, press 7
6 Select Save Changes to make the settings.
to stop it.
Video Language General
Setup Navigator
2 Press DVD SETUP.
Save Changes
Delete Changes
Start Again
Exit Setup Navigator
The Setup Navigator on-screen display (OSD) appears:
Changes are saved
ENTER
SETUP
Exit
Move
Select
Video Language General
Setup Navigator
7 Press DVD SETUP to exit.
Congratulations, set up is complete!
Setup Navigator
Start
Auto Start Off
Setup using the Setup Navigator
ENTER
SETUP
Exit
Move
Select
If you want to use the Setup Navigator again at any
time, it is available from the General menu. Also,
each individual setting can be changed using the
appropriate menu option—chapter 11 explains all
menu options in detail.
Navigate all of the following OSDs using these controls:
5, ∞ – cursor up/down
ENTER – select the highlighted menu option
2 – go back to the previous question
The control possibilities for the current OSD are shown
at the bottom of each screen.
18
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
5
• Do not place discs in the two partially accessible disc
spaces, as it’s easy to misalign them. Use only the front-
most space.
Playing DVDs, CDs and Video CDs
The basic controls for playing discs are covered here.
Further functions are detailed in the chapter 7.
• When using the DISC SKIP button, wait until the
disc tray has come to a complete stop before loading a
disc; the player may malfunction if a disc is caught in
the disc tray mechanism.
DVD
/CD
STANDBY
/ON
DSP
VOLUME
—
+
• Do not rotate the disc tray by hand. Always use the
5
ENTER
DISC SKIP button.
2
3
TOP MENU
MENU
∞
RETURN
7
6
5 Press 6 to start playback of the disc
just loaded.
—
PREV
e
STEP/SLOW
E
NEXT
+
4
1
¡
¢
1
4
7
2
5
8
3
6
9
>10
• If you’re playing a DVD or Video CD, a menu may
appear. See page 20 for how to navigate these.
10/0
DISC
1
DISC
DISC
2
4
DISC
3
5
DISC SKIP
OPEN/
SHIFT
DISC
CLOSE
0
Basic playback controls
Button
What it does
6
Starts playback or pauses a disc that’s
playing (press again to restart playback).
DVD and Video CD only: Resumes playback
of a stopped disc.
1 Press STANDBY/ON to turn on the
player.
7
Stops playback. DVD and Video CD only:
Display shows resume (press 6 to start
playback again from the last place
stopped).
2 Press DVD/CD.
3 Press OPEN/CLOSE 0 to open the disc
tray.
1
Press & hold for fast reverse scanning.
(After 5 seconds, scanning continues even
after releasing the button: press 6 to
resume normal playback.)
4 Load a disc.
On the front panel use: 4·1
¡
Press & hold for fast forward scanning.
(After 5 seconds, scanning continues even
after releasing the button: press 6 to
resume normal playback.)
On the front panel use: ¡·¢
4
¢
Skips to the start of the current track or
chapter, then to previous tracks/chapters.
On the front panel use: 4·1
Load a disc with the label side facing up, using the disc
tray guide to align the disc (if you’re loading a double-
sided DVD disc, load it with the side you want to play
face down).
Skips to the next track or chapter.
On the front panel use: ¡·¢
If you want to load more discs, press DISC SKIP to
rotate the disc tray. You can load up to five discs at once.
19
En
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Getting Started
Numbers
If the disc is stopped, playback starts from
Navigating DVD disc menus
the selected track or title number. If the
disc is playing, playback jumps to the start
of the selected track or chapter number.
Some DVD discs contain menus. Sometimes these are
displayed automatically when you start playback; others
only appear when you press menu or top menu.
>10
Selects tracks/titles/chapters 11 and over.
(For example, for 24, press >10 , 2, 4.)
Button
What it does
TOP MENU
Displays the ‘top menu’ of a DVD disc—
this varies with the disc.
DISC 1–5
Starts playing the selected disc.
(On the front panel use: 1–5)
(SHIFT MENU)
MENU
Displays a DVD disc menu—this varies with
the disc and may be the same as the ‘top
menu’.
DVD and Video CD only:
E
(SHIFT ¡) During playback, press and hold to start
slow-motion forward scanning. Change the
speed using the e and E buttons.
During playback, press once to pause;
advance a single frame with each subse-
quent press.
RETURN
Returns to the previously displayed menu
screen.
2 3 5 ∞
ENTER
Moves the cursor around the screen
Selects the current menu option
DVD only:
Numbers
Selects a numbered menu option (some
discs only)
e
(SHIFT 1) During playback, press and hold to start
slow-motion reverse scanning.
During playback, press once to pause;
reverse a single frame with each subsequent
press.
Navigating Video CD PBC menus
Some Video CDs have menus from which you can
choose what you want to watch. These are called PBC
(Playback control) menus, and are displayed
automatically when you start playback.
While using the DVD playback controls, you may see the
or mark displayed on-screen.
You can switch PBC off by starting playback using a
number button to select a track, rather than the 6
button.
means that the operation is not allowed by the
system.
means that the operation is not allowed by the disc.
Button
What it does
RETURN
Displays the PBC menu.
Numbers
Selects a numbered menu option.
4
Displays the previous menu page (if there is
one).
¢
6
Displays the next menu page (if there is
one).
Press to select an item from a PBC menu.
20
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
5
Exchanging discs
Listening to the radio
You can change any of the discs not in the play position
using the EXCHANGE button. Because the disc in the
play position is unaffected, you can use this button to
change discs even during playback.
The following steps show you how to tune in to FM and
AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. Once you are tuned to
a station you can memorize the frequency for recall
later—see Saving station presets on page 22 for more
on how to do this.
1 Press EXCHANGE to open the disc tray
without interrupting playback.
2 Load a disc.
TUNER
/BAND
TV
/AUX
SYSTEM SETUP
ENTER
2
3
–
PREV
e
STEP/SLOW
E
NEXT
+
4
1
¡
¢
1
4
7
2
MONO
3
6
9
5
8
>10
10/0
You can load two discs at a time in the two fully
accessible disc spaces. Do not try and load discs into any
of the other spaces; they may not load correctly and
cause the unit to malfunction.
SHIFT
3 If you want to load more discs, press
DISC SKIP to rotate the disc tray.
4 Press 0 OPEN/CLOSE or EXCHANGE to
close the disc tray.
1 Press TUNER/BAND to select the tuner.
On the remote, press repeatedly to switch between FM
and AM bands. On the front panel, the TUNER/BAND
button switches between FM, AM and preset station
mode. For now, choose either FM or AM.
• Do not push the disc tray shut by hand after
exchanging discs.
2 Tune to a station.
There are three ways to do this:
• Automatic tuning
To search for stations in the currently selected band,
press and hold either the 1 or ¡ button for about
a second. The system will start searching for the next
station, stopping when it has found one. Repeat this step
to search for other stations. Every time searching stops
on a station, the (tuned) indicator lights in the
display.
21
En
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Getting Started
• Manual tuning
5 Press 2 or 3 to select a station preset
number.
To change the frequency one step at a time, press the
Alternatively, use the number buttons (use the >10
button for numbers over 10).
1 / ¡ buttons. When you locate a station signal,
the (tuned) indicator lights in the display.
If you use the number buttons, you can skip step 6.
• High-speed tuning
Press and hold the 1 or ¡ button for high speed
tuning, releasing the button once you reach the
frequency you want. When you stop on a station signal,
the (tuned) indicator lights in the display.
6 Press ENTER again to save the station
preset.
Repeat these steps to save up to 30 station presets.
Listening to station presets
Having saved up to 30 station presets, you can be
listening to a station with a couple of button presses.
Improving FM stereo sound
If you’re listening to a stereo FM broadcast, but find that
there is a lot of noise because of a weak signal, try
switching to mono.
1 Press TUNER/BAND to switch to the
tuner.
•
Press MONO (SHIFT & 5) to switch
between mono and stereo.
When listening in mono, the indicator lights in the
display.
If you’re using the front panel controls, press TUNER/
BAND repeatedly to select the preset station mode.
2 Use 4 or ¢ to select the station
preset you want to listen to.
Alternatively, use the number buttons (use the >10
button for numbers over 10).
Saving station presets
If you often listen to a particular radio station, it's
convenient to have the receiver store the frequency for
easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time.
This system can save up to 30 station presets. When
saving FM frequencies, the receiver also saves the mono
setting (see Improving FM stereo sound above).
• If the system is left disconnected from the AC power
outlet for a lengthy period, the station presets will be lost
and will have to be reprogrammed.
Listening to other components
You may have connected your TV, VCR, or other
components to play through this system. Use the TV/
AUX button to select your external equipment as the
source.
1 Tune to a station you want to memorize.
See Listening to the radio on page 21 for more on how
to do this.
1 Press TV/AUX.
2 Press SYSTEM SETUP.
Press repeatedly to switch between:
3 Press 2 or 3 until you see ST. MEMORY
• TV inputs
appear in the display.
• DIGITAL input
• AUX analog inputs
4 Press ENTER.
2 Start playing the source component.
22
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Surround Sound
6
Adjusting the bass and treble
The simplest way to shape the sound is by adjusting the
amount of bass and treble.
Using sound modes
The sound modes allow you to add various surround
and room-type sound effects to your DVDs, CDs and
other sources. These effects process the sound in various
ways to simulate different spaces such as a theater, or
concert hall.
• The bass and treble controls have no effect when
using the DSP modes, or when the surround mode is set
to anything other than STANDARD, AUTO or
SURR. OFF (surround off).
For Dolby Surround, Dolby Digital or DTS surround
sources, such as DVDs, use the Advanced Theater effects
to add room ambience to the sound; for stereo-only
sources, such as audio CDs, use the DSP modes.
• You cannot adjust the bass or treble when Record
mode is active (see Direct recording on page 25).
For each effect you can also adjust how strong the effect
sounds. Often, a more subtle effect level enhances the
sound better than turning it right up. Experiment to see
what works best for you.
1 Press SOUND.
2 Use the 2 or 3 buttons to select BASS or
TREBLE.
Listening to surround-sound sources
When you play DVD discs with Dolby Digital or DTS
sound, choose from the following sound settings.
3 Use the 5 and ∞ buttons to adjust the
sound.
You can see the current level in the display.
• Auto – For digital sources, decoding is automati-
cally selected according to the source: Dolby Digital,
DTS, Dolby Pro Logic, 2-channel stereo, etc. No extra
effects are added to the source. Analog sources are
played in the same way as the Surround Off setting.
4 Press ENTER.
Using P.Bass
In addition to the standard controls for adjusting bass
and treble, this system has a P.Bass feature. Switch this
on to further extend the bass.
• Standard – As Auto, except that 2-channel
(analog or digital) sources are processed using Dolby
Pro Logic for surround-sound effects.
The following six settings are Advanced Theater effects.
• Musical – Concert hall sound.
• P.Bass has no effect when listening through
headphones.
• Drama – Classic, mid-size movie theater sound.
• Action – Large, modern movie theater sound.
• You cannot adjust P.Bass when Record mode is active
(see Direct recording on page 25).
• Virtual Surround 1 (VIR.SURR.1) –
Virtual surround sound from just the main front stereo
speakers and a subwoofer. Use this mode if you can't use
the surround speakers.
1 Press SOUND.
2 Use the 2 or 3 buttons to select P.BASS.
3 Use the 5 and ∞ buttons to switch on or
• Virtual Surround 2 (VIR.SURR.2) –
Virtual surround sound if you have connected the
surround speakers, but are using them in front of the
listening position.
off.
4 Press ENTER.
• Rear Wide – Widens the rear channel
soundstage.
23
En
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Using Surround Sound
• Surround Off (SUR.OFF) – All sources are
played through only the front left and right speakers,
and the subwoofer. No effects are added.
• The DSP effects cannot be used in combination with
the surround modes or with 96kHz digital sources.
• When playing stereo sources with DSP effects
switched off, there is no sound from the surround and
center speakers.
• The surround modes cannot be used in combination
with DSP effects or with 96kHz digital sources.
• You cannot change the DSP mode when Record
mode is active (see Direct recording on the following
page).
• You cannot change the surround mode when Record
mode is active (see Direct recording on the following
page).
1 Press DSP to select a sound mode.
Each press changes the mode as follows:
1 Press SURROUND MODE.
Each press changes the surround mode as follows:
• HALL 1
• HALL 2
• JAZZ
• DANCE
• THEATER 1
• THEATER 2
• SIMULATED STEREO
• DSP OFF (no effects added)
• AUTO
• STANDARD (surround on, with no Advanced
Theater effect)
• MUSICAL
• DRAMA
• ACTION
• VIR.SURR.1
• VIR.SURR.2
• REAR WIDE
Adjusting the effect level
• SUR.OFF (surround off)
You can adjust the effect level when using one of the
DSP effects or Advanced Theater effects. It is not possible
to change the effect level of the AUTO or STANDARD
surround mode (or when DSP or Surround modes are
off).
Listening to other sources with room
effects
You can add room effects to audio CDs and other stereo
sources using the DSP modes. Different effects work
better with different kinds of music, so don’t be afraid to
experiment a little.
• You cannot change the effect level when Record
mode is active (see Direct recording on the following
page).
There are seven DSP effects to choose from:
• Hall 1 – Large, wood-paneled concert hall sound.
• Hall 2 – Large, stone-walled concert hall sound.
• Jazz – Live jazz club sound.
1 Press SOUND.
• Dance – Nightclub sound.
2 Use the 2 or 3 buttons to select EFFECT.
• Theater 1 – Classic, mid-size movie theater
sound.
• Theater 2 – Large, modern movie theater sound.
• Simulated Stereo – Virtual stereo for mono
sources.
3 Use the 5 and ∞ buttons to adjust the
effect level.
You can adjust the effect level in the range of 10 to 90.
4 Press ENTER.
24
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Surround Sound
6
Listening at low volume
Direct recording
When the volume is low, surround effects tend to
become less than satisfactory. Turn the Midnight
listening mode on to enjoy quality surround sound even
at low volumes.
This feature let’s you record directly to an external
recorder, without worrying about the various sound
settings. The bass, treble, surround, DSP and Midnight
settings are all bypassed so that the recording is direct-
from-source.
1 Press SOUND.
2 Use the 2 or 3 buttons to select
M.NIGHT.
•
When the Record Mode is on you cannot change or
adjust the bass, treble, surround and DSP mode settings
or the Midnight setting.
3 Use the 5 and ∞ buttons to turn ON or
OFF.
•
Once the power is switched off or the function is
changed, the Record mode automatically reverts to off.
The LFE channel is not recorded.
4 Press ENTER.
•
• You cannot change the Midnight mode when Record
mode is active (see Direct recording right).
1 Press SOUND.
2 Use the 2 or 3 buttons to select
RECORD MODE.
3 Press ENTER.
The display shows RECMODE ON.
4 Press ENTER again.
The Record Mode is now active.
•
To switch off the Record Mode, repeat the same
proceedure. In step 3 above the display shows
RECMODE OFF.
25
En
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Playing Discs
•
To switch the camera angle, press ANGLE
(SHIFT & 4).
Introduction
• Most of the functions covered in this chapter apply to
• To hide the TV angle indicator, choose Angle
Indicator > Off from the Video menu (see page
39).
DVD discs, Video CDs and CDs, although the exact
operation of some varies slightly with the kind of disc
loaded.
• When playing DVD discs, if the
or icon
appears on-screen when you try and use a particular
function, either the player or the disc doesn’t allow the
use of that function.
Switching subtitles
Many DVD discs have subtitles in one or more lan-
guages—the disc box will usually tell you which
subtitle languages are available. You can switch subtitle
language anytime during playback.
• When playing Video CDs, some of the functions are
not available in PBC mode. You can switch PBC off by
starting playback using a number button to select a
track, rather than the 6 button.
•
•
To display/switch the subtitle language,
press SUBTITLE repeatedly.
To switch off subtitles, press SUBTITLE
then CLEAR.
Finding what you want on a disc
• To set subtitle preferences, see pages 40, 41.
You can directly access any point on a disc using one of
the search modes. Use these search modes while a disc is
playing, or when it’s stopped—playback immediately
starts from the point specified.
Switching audio language
When playing a DVD disc recorded with dialog in two or
more languages, you can switch audio language
anytime during playback.
1 Press SEARCH (SHIFT & 3) (remote only)
to choose between:
•
•
To display the current audio language,
press AUDIO.
• Title search (DVD only)
• Chapter/Track search
• Time search (DVD and Video CD only)
• Off
To switch the audio language, press
AUDIO repeatedly.
• To set audio language preferences, see page 40.
2 Enter the title/chapter/track number or
time (minutes & seconds).
For example, for title 4, press 4.
Switching audio channel
For chapter/track 12, press 1 , 2.
For 45 minutes into the disc,
press 4, 5, 0, 0.
When playing a CD or Video CD, you can switch between
the stereo soundtrack, just the left channel, or just the
right.
3 Press 6 to start/restart playback.
•
To switch the audio channel, press AUDIO
repeatedly.
Switching camera angles
Some DVD discs feature scenes shot from two or more
angles—check the disc box for details: it should be
marked with a icon if it contains multi-angle scenes.
When these scenes are playing, a camera icon ( )ap-
pears on-screen.
26
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Discs
7
3 Move the cursor to the TITLE/TRACK
field and enter a title or track number.
Making a program list
Title
Step
Disc
Chap
Program
Track
Making a program list means telling the player which
tracks, and in what order, you want played. You can
program a sequence of up to 24 tracks/chapters to play
from any of the discs loaded in the disc changer. The
discs can be any combination of DVD, Video CD and
audio CD. Chapters/tracks can appear more than once
in the playlist, or can be left out entirely.
1
2
3
4
5
6
1
06
Disc
1
DVD
Total 37 Title
4
¢
Page
PLAY
Play
PROGRAM
Exit
Move
For DVDs, this number will be a disc title; for Video CDs
and audio CDs, a track number.
For example, to enter title/track 6, press 6. To enter
title/track 14, press 1, 4.
1 Press PROGRAM (SHIFT & 7).
Title
Program
Step
Disc
Chap
Track
1
2
3
4
5
1
2
3
4
5
6
1
Disc
DVD
VCD
???
• To clear an entry, press CLEAR.
DVD
CD
• DVD only: If you want to put the whole title into the
program list, jump to step 5 below.
4
¢
Page
PLAY
PROGRAM
Exit
Move
Play
4 If the current disc is a DVD, move the
cursor to the CHAPTER field and enter a
chapter number.
The program screen appears showing the first six steps
in the playlist. Navigate around this screen using the
cursor buttons. Jump to the next six steps using the
¢ button; to the previous six steps using the 4
button.
Title
Step
Disc
Chap
Program
Track
1
2
3
4
5
6
1
6
10 Disc
Title
1
6
DVD
Total 10 Chapter
2 Enter a disc number (1 to 5).
You can use either the DISC1–5 buttons, or the
number buttons.
4
¢
Page
Move
PLAY
Play
PROGRAM
Exit
5 Press ENTER.
The cursor moves down to the disc number field in the
next step.
• If this is the first step you’re programming, the
number of the disc that is currently in the play position
will appear automatically.
6 Repeat steps 2-5 to add more items to
the program list.
• If the unit has already read the contents of the disc
you want to program, the disc details appear in the box
on the right of the screen (type of disc, number of titles/
chapters/tracks, etc.). If the unit hasn’t yet read the disc
then ‘? ? ?’ appears in the box for disc type.
7 Press 6 to start the program list
playing.
• If you want to put the whole disc into the program
list, jump to step 5 below.
• To edit any item in the program list, position the
cursor on the item you want to change, then enter a
new value using the number buttons.
• To delete a whole step, position the cursor anywhere
on the step you want to delete and press CLEAR.
27
En
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Playing Discs
1 Press RANDOM (SHIFT & 8) repeatedly
to select a random play mode.
The mode is displayed on-screen and in the front panel
display:
• The playlist remains active even if you open the disc
tray and change discs. If a step in the program list
cannot be played (because the track number is too
high, for example), that step is automatically skipped.
• To delete the playlist, stop playback, then press
• Random Chapter (from within the current
CLEAR.
title)
• Random Title
• You may see an asterisk (*) appear on-screen when
program play of some DVD discs starts. The asterisk
means that the part of the disc being played is not in the
playlist, but has to be played whenever the disc is first
loaded in to the play position. The asterisk will
• Random 1 Disc
• Random All Discs
disappear once the programmed chapters start playing.
2 Press ENTER or 6 to start random play.
• To stop the disc and cancel random playback,
press 7.
More programming options
There are several other options available when making/
using program lists.
• To cancel random playback without stopping
playback, press CLEAR. The rest of the disc plays out.
•
•
To view the playlist, press PROGRAM
(SHIFT & 7).
During random play, the 4 and ¢ buttons
function a little differently to normal: 4 returns to
the beginning of the current track/chapter. You can't go
back further than this. ¢ selects another track/
chapter at random from those remaining.
To delete an entry from the playlist,
position the cursor on the title/chapter/
track number and press CLEAR.
•
•
To add an entry to the end of the playlist,
press PROGRAM (SHIFT & 7), enter the
title/chapter/track number, then press
program again.
Using repeat play
You can set the player to repeat individual tracks on CDs
or Video-CDs, chapters or titles on DVD discs, a whole
disc, or all the discs loaded in the player. It's also
possible to loop a section of a disc.
To delete the playlist, exit the program
list screen, stop playback, then press
CLEAR.
You can use the repeat together with the programming
mode to repeat the tracks/chapters in the playlist (see
page 27 for how to program a playlist).
Using random play
Use the random play function to play titles/chapters/
tracks in a random order.
1 Press REPEAT (SHIFT & 9) during play-
back to select a repeat mode.
How random play works depends on the disc currently
in the play position. If the ‘current’ disc is a DVD, you
can play either the titles or chapters on that disc at
random. If the ‘current’ disc is an audio or Video CD,
you can play either the tracks on that disc, or all the
tracks on all the CDs and Video CDs loaded at random
(DVD discs loaded will be ignored).
Each press switches the repeat mode:
• Chapter Repeat
• Title Repeat
• Repeat Off
28
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Discs
7
2 Press 6.
The player automatically starts playing the first CD
• Track Repeat
• 1 Disc Repeat
• All Discs Repeat
• Repeat off
loaded. Once all the CDs loaded have played, the player
automatically stops.
• The Repeat All function repeats all tracks on all
audio and Video CDs loaded. If, during repeat play, the
unit encounters a DVD disc, it will start playing, but the
repeat mode will be canceled.
• In CD Mode, use the DISC SKIP button to rotate the
disc tray to the next CD loaded (if there is one).
• You can use repeat and random play in CD Mode
(see page 28 and this page).
2 To resume normal playback, press CLEAR.
• You can't switch on CD mode while playing a DVD or
Video CD. Stop playback first.
You can use repeat play with program play and random
play. During program/random play, press REPEAT
(SHIFT & 9).
• Program play is not possible in CD Mode. However, it
is possible to program a playlist. When you start
program play, CD Mode is canceled (see page 27).
Looping a section of a disc
•
Press REP A-B (SHIFT & 10/0) once at
the start of the section you want to
repeat, then again at the end.
Bookmarking a place in a disc
Playback immediately jumps back to the start point and
plays the loop repeatedly.
If you watch only part of a DVD disc with the intention
of picking up later where you left off, you can bookmark
the place then resume playback at a later date without
having to manually search for the right place.
• On a DVD disc, the start and end points of the loop
must be in the same title.
You can use this feature for up to five discs (after that
the oldest bookmark is deleted to make space for a new
one).
• To resume normal playback, press CLEAR.
•
To repeat a section of a disc just once,
press REP A-B (SHIFT & 10/0) at the
start of the section, then 6 at the end.
Playback jumps back to the start point.
•
•
At the point from which you want to
resume playback next time, press LAST
MEMO (SHIFT & 2).
Press 7 if you want to stop playback here.
Playing CDs only (CD Mode)
Using this feature you can play only the CDs loaded in
the disc tray—automatically skipping over any DVDs or
Video CDs loaded. This may be useful if you have a
mixture of discs loaded but only want to play music:
you don't have to keep track of what kind of disc is
where in the disc tray.
To resume playback, load the disc and
press LAST MEMO (SHIFT & 2).
If the disc starts auto playback, stop it first.
• To clear the bookmark for the disc loaded, press
LAST MEMO (SHIFT & 2) then CLEAR while Last
Memory is displayed on-screen.
1 Press CD MODE.
The CD Mode indicator lights.
• Bookmarking also works with Video CD, but for one
disc only, and you must leave the disc in the player—
opening the disc tray erases the memory. Last Memory
may not work reliably with some PBC Video CDs.
• To switch off, press CD MODE again.
29
En
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Playing Discs
• When a disc is stopped, all title/chapter, or track
information for the disc loaded appears on-screen. Press
DVD DISP(SHIFT & CLEAR) again to exit the screen.
Memorizing disc settings
If you have a particular set of preferences for a disc, you
can memorize them using the Condition Memory
function. Once memorized, your settings will be recalled
automatically whenever you load that disc. The player
can store settings for 15 discs; after this, memorizing
another replaces the oldest one stored.
Information: DVD
Title
01
02
03
04
Chapter Title
Chapter
1~ 10
1~ 13
1~ 5
1~ 30
1~ 21
1~ 46
1~ 12
1~ 8
06
07
08
09
1~ 4
05
DISPLAY
Exit
1/1
The settings memorized are:
DVD-Video
• OSD Position (page 39)
• Subtitle Language (page 40)
• Audio Language (page 40)
• Angle Indicator (page 39)
• Parental Lock level (page 42)
Information: Compact Disc
Total Time
6.30
Track
Time
3.32
2.58
01
02
•
•
To memorize settings for the current disc,
press CONDITION (SHIFT & 1) during
playback.
DISPLAY
Exit
1/1
CD/Video CD
To recall memorized settings, just load
the disc.
• To display the time remaining on a DVD disc, press
and hold DVD DISP (SHIFT & CLEAR).
The display shows CONDITION and Condition
Memory appears on-screen.
The display shows the disc time remaining for as long
as you hold the button. Release the button to revert to
the previous display.
•
To clear memorized settings, load the disc and press
CLEAR while Condition Memory is displayed on-
screen.
Displaying disc information
Various track, chapter and title information, as well as
the video transmission rate for DVD discs, can be
displayed on-screen while a disc is playing, or while it’s
stopped.
•
To show/switch the information dis-
played, press DVD DISP (SHIFT & CLEAR).
• When a disc is playing, the information appears at
the top of the screen. Keep pressing DVD DISP (SHIFT
& CLEAR) to change the displayed information.
Play
Tr. Rate
37—1 0.38
7.2
:
DVD data transmission rate display
30
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Discs
7
6 Adjust the MIC LEVEL to get the sound
you want.
Singing karaoke (Except European
model)
If when you turn the MIC LEVEL up, you get a loud
whistling from the speakers, move the microphone so
that it points away from the speakers.
Using the karaoke features you can plug in a micro-
phone and mix the sound of your own voice with a
backing track. The backing track can be anything you
like, from a song on the radio, to a dedicated DVD
karaoke disc that displays the lyrics on screen as the
music plays. Tailor the mix by adjusting the micro-
phone level relative to the backing track.
7 Sing!
Note: Depending on the microphone level, the sound
of the disc may distort. If this happens, turn down the
volume.
1 Set MIC LEVEL to minimum.
2 Plug in the microphone.
DISC SKIP EXCHANGE
0
OPEN/CLOSE
The mic jack is located on the front panel.
1
2
3
4
5
VIDEO
• If the microphone has an on/off switch, make sure
OLUME
DVD RECEIVER XV-HTD1
STANDBY/ON
it’s on.
STANDBY
CD
MODE
ADVANCED
THEATER
DSP
DISC
MIC
LEVEL
Karaoke
1
MIC
PHONES
.
DVD/CD
TUNER/BAND
TV/AUX
CD MODE
7
3/8
4
1
3 Load a karaoke backing disc.
You can also use the radio or a component connected to
the auxiliary inputs as source material for a backing
track.
4 To change the mix (CD or VCD only),
press AUDIO.
Pressing repeatedly switches between these modes:
• STEREO – Use for backing tracks with no vocals.
• L CH – Left channel only. Use for tracks that have a
vocal recorded in the right channel.
• R CH – Right channel only. Use for tracks that have
a vocal recorded in the left channel.
5 Play the backing track.
31
En
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Using RDS (European model only)
RDS Program types
Using RDS
News
News
Current affairs
General information
Sports
Educational material
Radio drama
Arts and culture
Science and technology
Usually talk-based material, such as
quiz shows or interviews.
Pop music
Radio Data System, or RDS as it’s usually known, is a
system used by FM radio stations to provide listeners
with various information—the name of the station and
what kind of show they’re broadcasting, for example.
RDS allows you to search through stations automati-
cally using this information. It shows up as text on the
display, and you can switch between the type of
information shown. Although you don’t get RDS
information from all FM radio stations, you do with
most.
Affairs
Info
Sport
Educate
Drama
Culture
Science
Varied
Pop M
Rock M
This unit lets you display three different kinds of RDS
information: Radio Text, Program Service Name, and
Program Type.
Rock music
M.O.R. M "Middle of the road" music
Light M
Classics
'Light' classical music
'Serious' classical music
Radio Text (RT) is a message sent by the radio station.
It can be anything the broadcaster chooses—a talk
radio station might give out its telephone number as
RT, for example.
Other M Other music not fitting any of the
above categories
Weather Weather reports
Finance
Children Children’s' entertainment
Social Social affairs
Program Service Name (PS) is the name of the radio
station.
Finance and business
Program Type (PTY) indicates the kind of program
currently being broadcast.
Religion Religious programming
Phone in Phone in talk show
Travel
Holiday-type travel rather than traffic
announcements, etc.
Leisure interests and hobbies
Jazz music
Leisure
Jazz
Country Country music
Nation M Popular music in a language other
than English
Oldies
Folk M
Popular music from the '50s
Folk music
Document Documentaries
In addition, there are program types, ALARM and
TEST, used for exceptional emergency announcements.
The tuner will switch automatically to that station if it
picks up either of these RDS signals.
32
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using RDS (European model only)
8
Displaying RDS information
You can choose to display Program Service name (PS),
Program Type (PTY), or Radio Text (RT) for the FM
station you're listening to.
Searching for a program type
You can search for a station that is broadcasting any
program type from the list on page 32.
1 Select FM with the TUNER/BAND button.
1 Press SYSTEM DISP repeatedly to select
the RDS information you want to display.
Switch between:
2 Press SYSTEM DISP repeatedly until
SEARCH appears in the display.
3 Use 4 and ¢ to choose the program
type, then press SYSTEM DISP.
You can search for any of the program types listed on
page 32.
• PS (Program Service name)
• PTY (Program Type)
• RT (Radio Text)
• SEARCH (see below for more on this)
• OFF (don't display any RDS data)
After pressing DISP/RDS, the system starts searching
through the station presets for a match. When it finds
one, the search stops and the station plays for 6 seconds.
The RDS information will appear after a few seconds.
4 If you want to keep listening to the
station, press SYSTEM DISP within the 6
seconds.
• The RDS indicator will light in the RDS mode.
If you don't press SYSTEM DISP, searching resumes.
• If no RDS signal can be received, the no data
message will be displayed.
• If there is noise during the RT scroll display when in
the RT mode, some characters may be temporarily
displayed incorrectly.
• In the RT mode, when no RT data is transmitted, no
radio text data is displayed.
• During RDS broadcast reception in the PTY mode,
no type data may be displayed. In this case, it will
automatically switch to PS mode after a few seconds.
33
En
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Using the Timer
9 Set the switch off time.
Set in the same way as the switch on time, pressing
ENTER to finish.
Using the wake up timer
You can use the timer as an alarm clock to wake up to
the sound of a disc loaded or the radio. If you have an
external component operated by a separate timer, you
can also set it as the source function.
• If you make a mistake, press SYSTEM SETUP and
start again from step 3.
Once the timer is active, it will switch the system on
everyday at the set time.
10 Check the settings you just made.
The display should indicate that you have set the wake
up timer, then show the on time, the off time, the
function (DVD, etc.), and the volume. The display
shows CHECK END after all the settings.
Unlike an ordinary alarm clock, you need to set a
system switch off time, as well as a switch on time.
1 Select the source that you’d like to wake
up to.
• There is no direct way to edit the timer settings. If
you see that some timer setting is not what you’d
intended, you’ll need to start the process again from the
top.
For a disc, press DVD/CD; for the radio press TUNER/
BAND; for an external component, press TV/AUX.
2 Load a disc or tune to a radio station,
then set the volume.
11 Switch the system into standby.
The timer will not work if the system is left on!
If you selected an external component, make the
appropriate timer settings for it.
The timer indicator ( ) lights when the timer is on.
3 Press SYSTEM SETUP.
4 Press 2 or 3 until you see TIMER in the
Activating/deactivating the wake up
timer
display.
To activate the wake up timer, set the timer to ON. To
deactivate it, set the timer to OFF.
5 Press ENTER.
6 Press 2 or 3 until you see WAKE UP SET
in the display.
1 Press SYSTEM SETUP.
7 Press ENTER.
2 Press 2 or 3 until you see TIMER in the
display.
The display shows a switch on time with the hour
blinking.
3 Press ENTER.
8 Set the switch on time.
Use 5 and ∞ to set the hour then press ENTER. Set the
minute in the same way, pressing ENTER to finish.
4 Press the 2 or 3 button until you see
TIMER ON or TIMER OFF in the display.
5 Press ENTER.
• If you make a mistake, press SYSTEM SETUP and
start again from step 3.
The timer indicator ( ) lights when the timer is on.
34
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timer
9
Checking the timer settings
If you’ve set the wake-up timer, you can check the
settings anytime.
Using the sleep timer
The sleep timer switches the system into standby after a
specified amount of time so that you can fall asleep
without worrying about the stereo being left on all
night. If you've also set the wake up timer this is
important since the wake up timer will only work if the
system is in standby.
1 Press SYSTEM SETUP.
2 Press 2 or 3 until you see TIMER in the
display.
3 Press ENTER.
1 Press SLEEP (SHIFT & 6) to set the time
until the system goes into standby.
Press repeatedly to switch between:
4 Press the 2 or 3 button until you see
TIMER CHECK in the display.
• SLEEP AUTO – this setting is only available when
the system is playing a CD*
• SLEEP 90 (minutes)
• SLEEP 60 (minutes)
• SLEEP 30 (minutes)
5 Press ENTER.
The display shows the timer settings:
• On time
• Off time
• Function (DVD, etc.)
• Volume
• SLEEP OFF (cancels the sleep timer)
The sleep timer indicator ( ) lights and the display
dims when the sleep timer is active.
• CHECK END
* This is not available when a Video CD is in PBC mode,
or if you're playing a CD or Video CD in repeat mode. If
you set a disc playing in repeat mode after setting the
sleep timer to SLEEP AUTO, it automatically switches
to the 90 minute setting.
• Once the sleep timer is set, you can check the time
left by pressing SLEEP (SHIFT & 6).
• To cancel the sleep timer, switch the system into
standby, or select SLEEP OFF (as described above).
• If you switch to a different source when sleep auto is
set, the system will automatically go into standby a
minute later.
35
En
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Advanced Sound Setup
Dynamic Range Control
Advanced sound settings
This chapter covers advanced settings to further
optimize the sound of your system.
The dynamic range of a source is the difference between
the quietest and the loudest sounds. The dynamic range
of Dolby Digital soundtracks can be very great. This
makes them exciting, but it also means that when you
turn the volume down you can easily lose quiet dialog.
Switch on Dynamic Range Control to even out the
soundtrack volume.
LFE attenuator
The LFE (low frequency effects) channel carries ultra
low bass sound to add weight to effects in Dolby Digital
and DTS soundtracks. This channel can overload the
subwoofer resulting in distortion. Use the LFE attenua-
tor setting to reduce the signal fed to the subwoofer.
• You can’t change this setting if the Record mode is
on (see page 25).
1 Press SYSTEM SETUP.
The LFE attenuator only works with sources that
contain an LFE channel. It is not a general level control
for the sub-woofer.
2 Press the 2 or 3 button until you see
D.R.C. in the display.
3 Use the 5 and ∞ buttons to select a
dynamic range setting.
• You can’t change this setting if the Record mode is
on (see page 25).
• D.R.C. OFF – default setting (no change to the
dynamics)
1 Press SYSTEM SETUP.
• D.R.C. LOW – the dynamic range is reduced by a
small amount.
2 Press the 2 or 3 button until you see LFE
in the display.
• D.R.C. MID – mid setting
3 Use the 5 and ∞ buttons to set the
amount of signal reduction.
There are three settings:
• D.R.C. HIGH – the dynamic range is reduced by a
large amount (good for listening at very low volume).
4 Press ENTER.
• LFE ATT 0 – default setting (no signal reduction)
• LFE ATT 10 – the LFE channel signal level is
reduced to avoid distortion
• LFE OFF – the LFE channel is switched off
completely. This may be useful late at night, for
example.
4 Press ENTER.
36
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Sound Setup
10
Dual-mono setting
Adjusting channel volume levels
Depending on your room and where you’re sitting, you
may want to adjust the relative volumes of one or more
speakers for a more balanced sound. You can do this in
any mode, including the surround, DSP, and stereo
modes. Settings that you make in any sound mode are
completely independent and don’t affect any other
mode.
The dual-mono setting applies only to Dolby Digital
discs that feature dual-mono material—see the disc
box for details.
Dual-mono discs are recorded with two independent
channels that may be played together or separately
depending on the situation. For example, a guitar
tuition disc might have the guitar recorded on one
channel and all the other instruments on the other. Use
the dual-mono setting to play just the guitar part on its
own; just the backing, or everything together (through
separate speakers, or mixed).
• Each DSP effect has its own set of channel level
settings.
• The channel levels you set for the Surround mode
apply to Standard and all Advanced Theater effects.
• You can’t change this setting if the Record mode is
on (see page 25).
• The headphone level is not affected by the channel
level settings.
1 Press SYSTEM SETUP.
2 Press the 2 or 3 button until you see
1 Press CH LEVEL.
CH or MIX in the display.
Adjustments to the channel volume levels will affect
only the current sound mode.
3 Use the 5 and ∞ buttons to select a dual-
mono setting.
2 Use the 2 and 3 buttons to select a
channel to adjust.
• L-CH1 R-CH2 – default setting (Ch1 is played
through the left speaker; Ch2 through the right)
The display shows the channel and its current setting.
• CH1 – Ch1 is played through the center speaker
(or through the left and right speakers if Surround
Off is selected); Ch2 is muted.
• Remember that not all channels are available in all
sound modes.
• CH2 – Ch2 is played through the center speaker
(or through the left and right speakers if Surround
Off is selected); Ch1 is muted.
3 Use the 5 and ∞ buttons to adjust the
volume of the current channel.
For best results, sit in your main listening position when
doing this. You can adjust each speaker in the range of
+/-10dB.
• MIX – Ch1 and Ch2 are mixed together and played
through the center speaker (or through both left and
right speakers if Surround Off is selected).
4 When you're done, press ENTER.
4 Press ENTER.
37
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11 DVD Setup Menu
Using the DVD Setup menu
Video settings
TV Screen
• Set in Setup Navigator (Default: 16:9 (Wide))
Video Language General
DVD SETUP
5
TV Screen 4:3(Letter Box)
Picture Quality 4:3(Pan&Scan)
16:9(Wide)
ENTER
2
3
∞
RETURN
Select your display preference
SETUP
Move
Exit
If you have a widescreen TV, select the 16:9 (Wide)
setting—widescreen DVD software is then shown using
the full screen area. When playing software recorded in
conventional (4:3) format, the settings on your TV will
determine how the material is presented—see the
manual that came with your TV for details on what
options are available.
The DVD Setup menu gives you access to all the system’s
DVD settings. Press DVD SETUP to display/leave the
menu and the cursor (25∞3) and ENTER buttons
on the remote to navigate and select options. In some
screens you can press RETURN to leave the screen
without making any changes. The controls for each
menu are shown at the bottom of the screen.
If you have a conventional TV, choose either 4:3
(Letter Box) or 4:3 (Pan & Scan). In Letter
Box mode, widescreen software is shown with black bars
at the top and bottom of the screen. Pan & Scan chops
the sides off widescreen material to make it fit the 4:3
screen (so even though the picture looks larger on the
screen, you’re actually seeing less of the movie). See
page 50 for more information.
If an option is greyed out it means that it cannot be
changed at the current time. This is usually because a
disc is playing. Stop the disc, then change the setting.
Picture Quality
The current setting for any option is marked with a
colored box. The color of the box indicates what kind of
disc the setting is applicable to: blue for DVD only;
yellow for DVD and Video CD; green for any type of disc.
• Default setting: Standard
Language General
Video
TV Screen – 16:9(Wide)
Picture Quality
Cinema
Animation
Standard
Adjust picture quality
Move
•
The language options shown in the on-screen
SETUP
Exit
display illustrations on the following pages may not
correspond to those available in your country or region.
There are three preset picture quality settings that suit
various program types.
Cinema – Sharp, high contrast picture.
Animation – Bright, vibrant colors.
Standard – Neutral picture.
38
En
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Setup Menu
11
When watching DVD discs recorded in 4:3 format
(‘regular’ TV size) on a widescreen TV, it can be difficult
to see the operation displays (Play, Stop, Resume,
etc.) at the top of the screen. If you find them hard to
read, select Position – Wide.
S-Video Out
• Default setting: S2
Language General
Video
TV Screen – 16:9(Wide)
Picture Quality – Standard
S-Video Out
Still Picture
On Screen Display – Position Normal
Angle Indicator
S1
If you prefer not to have the operation displays shown
on-screen, change the setting to Off.
–
S2
–
On
SETUP
Move
Exit
Angle Indicator
• Default setting: On
You can switch the type of S-Video signal output. If you
connected your TV with an S-Video cord in some rare
cases the TV picture may appear stretched. If you find
this switch the S-Video output from S2 to S1.
Video Language General
TV Screen —16:9(Wide)
Picture Quality —Standard
S-Video Out —S2
Still Picture —Auto
On Screen Display — Position
-
Normal
Angle Indicator
On
Off
Still Picture
• Default setting: Auto
SETUP
Move
Exit
If you prefer not to see the camera icon on-screen
during multi-angle scenes on DVD discs, change the
Angle Indicator setting to Off.
Language General
Video
TV Screen —16:9(Wide)
Picture Quality —Standard
S-Video Out —S2
Still Picture Field
On Screen Display —
Frame
Angle Indicator —Auto
SETUP
Move
Exit
Language settings
The player uses one of two processes when displaying a
still frame from a DVD disc. The default Auto setting lets
the system decide which to use.
OSD Language
• Set in Setup Navigator (default: English)
Field – produces a stable, generally shake-free image.
Video Language General
Frame – produces a sharper image, but more prone to
shake than field stills.
OSD Language English
Audio Language -
français
Subtitle Language -
Español
Auto Language – On
Select the On Screen Language
On Screen Display
• Default setting: Position – Normal
SETUP
Move
Exit
Choose the language you want the OSDs in.
Video Language General
TV Screen —16:9(Wide)
Picture Quality —Standard
S-Video Out —S2
Auto
Still Picture —
On Screen Display
Position - Wide
Angle Indicator —
Position - Normal
Off
SETUP
Move
Exit
39
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11 DVD Setup Menu
disc, the system automatically plays the disc with those
subtitles (although this depends on the Auto Language
setting—see Auto Language on page 40).
Audio Language
• Default Setting: English
Video Language General
OSD Language — English
Video Language General
Audio Language -
English
Subtitle Language
List of Languages
Subtitle Language -
French
Auto Language - Spanish
Other
Code (0~2)
ja: Japanese
1
0
0
1
Setup audio language
Setup disc’s subtitle language
Move
SETUP
Move
Exit
RETURN
Return
Exit
+/–
ENTER
SETUP
Select
This setting is your preferred audio language for DVD
discs. If the language you specify here is recorded on a
disc, the system automatically plays the disc in that
language (although this depends on the Auto Lan-
guage setting—see Auto Language on page 40).
The DVD format recognizes 136 different languages.
Choose Other if you want to specify a language other
than those listed, then follow the on-screen display to
select a language. You may also want to refer to the
Language code list on page 47.
Video Language General
Audio Language
Code (0~2)
List of Languages
You can change or switch off the subtitles on a DVD disc
any time during playback using the SUBTITLE button.
(This does not affect this setting.)
ja: Japanese
1
0
0
1
Setup audio language
Move
+/–
RETURN
SETUP
Return
Exit
ENTER
Select
Auto Language
• Default Setting: On
The DVD format recognizes 136 different languages.
Choose Other if you want to specify a language other
than those listed, then follow the on-screen display to
select a language. You may also want to refer to the
Language code list on page 47.
Video Language General
OSD Language — English
Audio Language — English
Subtitle Language — English
Auto Language
On
Off
Play dialog, etc. in original language
Subtitle ON with foreign audio
You can switch between the languages recorded on a
DVD disc any time during playback using the AUDIO
button. (This does not affect this setting.)
SETUP
Move
Exit
When set to On, the system always selects the default
audio language on a DVD disc (French dialog for a
French movie, for example), and displays subtitles in
your preferred subtitle language only if that is set to
something different. In other words, movies in your
native language won’t have any subtitles, while foreign
language movies will be shown with subtitles.
Subtitle Language
• Default Setting: English
Video Language General
OSD Language — English
Audio Language —English
Subtitle Language French
Set to Off to have the system play discs strictly
according to your Audio Language and Subtitle
Language settings.
Auto Language -
Spanish
Other
Setup disc’s subtitle language
SETUP
Move
Exit
For Auto Language to work, the Audio Language and
Subtitle Language settings must be the same—see this
page.
This setting is your preferred subtitle language for DVD
discs. If the language you specify here is recorded on a
40
En
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Setup Menu
11
Set to On, the player displays subtitles according to the
Subtitle Language and Auto Language settings above.
Set to Off to switch subtitles off altogether (although
see Subtitle Off on this page for special cases). Set to
Assist Subtitle to have the player display the extra
assistive subtitles recorded on to some DVD discs.
You can still switch audio and subtitle languages on
playback using the AUDIO and SUBTITLE buttons.
DVD Language
• Default Setting: w/Subtitle Language
Subtitle Off
Video Language General
• Default Setting: Selected Subtitle
OSD Language — English
Audio Language — English
Subtitle Language
w/ Subtitle Language
Auto Language -
English
Language General
Video
DVD Language
French
Subtitle Display -
Spanish
OSD Language – English
Audio Language – English
Subtitle Language – English
Auto Language – On
Subtitle Off -
Other
SETUP
Move
Exit
DVD Language – English
With Audio
Subtitle Off SelectedSubtitle
Subtitle Display -
Some multi-lingual discs have disc menus in several
languages. This setting specifies in which language the
disc menus should appear. Leave on the default setting
for menus to appear in the same language as your
Subtitle Language—see page 40.
SETUP
Move
Exit
Some discs display subtitles even if the Subtitle Display
setting (this page) is set to off. In this case, you can
either have the subtitles displayed in the same language
as your preferred audio language (With Audio), or
in your preferred subtitle language (Selected
Subtitle). If the Audio Language and Subtitle
Language settings are the same then both of these
choices will give the same result.
Video Language General
DVD Language
Code (0~2)
List of Languages
ja: Japanese
1
0
0
1
RETURN
SETUP
Return
Exit
Move
+/–
ENTER
Select
The DVD format recognizes 136 different languages.
Choose Other if you want to specify a language other
than those listed, then follow the on-screen display to
select a language. You may also want to refer to the
Language code list on page 47.
General settings
Setup Menu Mode
• Default setting: Basic
Video Language General
Setup Menu Mode Expert
Subtitle Display
• Default Setting: On
Basic
Setup Navigator
Parental Lock — Level 8
Change menu mode
Move
SETUP
Video Language General
Exit
OSD Language – English
Audio Language – English
Subtitle Language – English
Auto Language – On
The Basic setup menu gives you access to the more
commonly used settings. It also features an information
bar which tells you more about what the currently
highlighted option means.
DVD Language -
On
Subtitle Display Off
Assist Subtitle
Subtitle Off - Selectetitle
Move
SETUP
Exit
Set to Expert for access to all settings.
41
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11 DVD Setup Menu
Parental Lock
• Default level: 8
Changing the parental lock level
1 Select Level Change.
• Default password: none
2 Use number buttons to register a new
password or confirm your existing pass-
word, then press ENTER.
Video Language General
Setup Menu Mode — Basic
Setup Navigator
Parental Lock Level Change
Password Change
Video Language General
Parental Lock: Register Code Number
Setup viewing restrictions
SETUP
Move
Exit
Enter 4–Digit Code
You can restrict access to certain discs using this feature.
Once set, the player will ask for a four-digit password if a
restricted disc is loaded, giving you a degree of control
over what your children watch.
Move
+/–
RETURN
SETUP
Exit
Return
The first time you set the parental lock level, you have
to register a password. Anything you input becomes your
password.
The player can be set to one of eight levels. Setting the
level at 1 means that any disc with any level of
restriction will need the password in order to watch it,
while setting it at level 8 gives unlimited access.
3 Select a new level.
Video Language General
DVD discs are also rated from 1 to 8. Discs rated 1 (or
with no rating) generally contain little or no offensive
material; discs rated 2, may contain material that some
parents may feel is unsuitable for children. Discs rated 8
will almost certainly be unsuitable for children.
Parental Lock: Level Change
1
Level
2
3
4
5
6
7
8
Set Parental Lock
RETURN
SETUP
Return
Exit
Move
ENTER
Select
Since a disc’s rating is up to the manufacturer, it is not
possible to give a definitive guide to each level—check
the disc box for parental lock details.
Move leftward to lock more levels (more discs will
require the password); rightward to unlock levels. You
can’t lock level 1.
4 Press ENTER to set the new level.
Not all discs that you may consider inappropriate for
your children are rated. Unrated discs will always play
without requiring the password first.
Changing your password
1 Select Password Change.
2 Input your existing password, then press
ENTER.
Video Language General
Parental Lock: Confirm Code Number
ENTER
Enter 4–Digit Code
Move
RETURN
SETUP
+/–
Return
Exit
42
En
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Setup Menu
11
3 Input a new password, then press ENTER.
This specifies the color of the screen when the player is
stopped (or playing an audio disc).
Language General
Video
Select Other if you want to make your own back-
ground color. Follow the on-screen display to create a
color from the red, green and blue bars.
Parental Lock: Password Change
Enter 4–Digit Code
Video Language General
Move
+/–
RETURN
SETUP
Exit
Return
Background color
If you forget your password, resetting the player will
clear the password. See page 44 for more on this.
RETURN
SETUP
Return
Exit
Move
–/+
ENTER
Select
Screen Saver
• Default setting: On
Video Language General
Setup Menu Mode
Setup Navigator
–
Expert
Parental Lock – Level 8
Screen Saver On
Background Color –
Off
SETUP
Move
Exit
If a constant image is displayed on a conventional CRT-
type TV, it can “burn in” leaving a ghost image on the
screen. When On, the screen saver makes sure that a
constant image is not displayed for a dangerously long
time.
Background Color
• Default setting: Blue
Video Language General
Setup Menu Mode
Setup Navigator
—
Expert
Parental Lock — Level 8
Screen Saver — Off
Background Color
Black
Blue
Other
SETUP
Move
Exit
43
En
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Additional Information
Switching the AM frequency interval
As its default setting, the tuner jumps in steps of 10kHz
when tuning in AM stations. If you find that this is
unsuitable in your area (if you can’t tune into stations
successfully), you can change the tuning interval to
9kHz for AM. Here’s how to switch the setting.
Resetting the system
Resetting the system returns all menu, picture and
password settings to their factory defaults.
1 Switch the system into standby using the
front panel standby/on switch.
2 Hold down the front panel 7 button and
switch back on.
1 Switch the system into standby.
2 Press SYSTEM SETUP.
3 Press the 2 or 3 button until you see AM
STEP in the display.
4 Use the 5 and ∞ buttons to select 9kHz
or 10kHz.
• When set to 9kHz, the FM tuning interval becomes
50kHz. This should not affect tuning into FM stations.
5 Press ENTER.
Setting the display brightness
You can adjust the brightness of the display to suit the
lighting conditions of the room.
•
Press FL DIMMER (SHIFT & >10).
Press repeatedly to set the display brightness. There are
five levels.
Switching the time format
You can display the clock in either 12 or 24-hour
format.
1 Switch the system into standby.
2 Press SYSTEM SETUP.
3 Press the 2 or 3 button until you see
CLOCK 12 HR or CLOCK 24 HR in the
display.
4 Use the 5 and ∞ buttons to select 12 or
24.
5 Press ENTER.
44
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
12
Storing discs
Taking care of your system
Although CDs and DVDs are more durable than vinyl
records, you should still take care to handle and store
discs correctly. When you’re not using a disc, return it to
its case and store upright. Avoid leaving discs in
excessively cold, humid, or hot environments (includ-
ing under direct sunlight).
To clean this unit, wipe with a soft, dry cloth. For
stubborn dirt, wet a soft cloth with a mild detergent
solution made by diluting one part detergent to 5 or 6
parts water, wring well, then wipe off the dirt. Use a dry
cloth to wipe the surface dry. Do not use volatile liquids
such as benzene and thinner which may damage the
surfaces.
Don’t glue paper or put stickers on discs, or write on
them using a pencil, ball-point pen or other sharp-
tipped writing instrument.
Disc lens cleaner
The disc pickup lens should not become dirty in normal
use, but if for some reason it should malfunction due to
dirt or dust, consult your nearest Pioneer authorized
service center. Although lens cleaners for CD players are
commercially available, we do not recommend using
them since some may damage the lens.
Discs to avoid
Discs spin at high speed during playback. If you can see
that a disc is cracked, chipped, warped, or otherwise
damaged, don’t risk using it—you could end up
damaging the system.
Taking care of your discs
When holding discs, take care not to leave fingerprints,
dirt or scratches on the disc surface. Hold the disc by its
edge or by the center hole and edge. Damaged or dirty
discs can affect playback performance. Take care also
not to scratch the label side of the disc. Although not as
fragile as the recorded side, scratches can still result in a
disc becoming unusable.
This system is designed for use with conventional, fully
circular discs only. Use of shaped discs is not recom-
mended. Pioneer disclaims all liability arising in
connection with the use of shaped CDs and DVDs.
Should a disc become marked with fingerprints, dust,
etc., clean using a soft, dry cloth, wiping the disc lightly
from the center to the outside edge as shown on the next
page. If necessary, use a cloth soaked in alcohol, or a
commercially available CD or DVD cleaning kit to clean
a disc more thoroughly. Never use benzine, thinner or
other cleaning agents, including products designed for
cleaning vinyl records.
• Wipe lightly from the center of the disc using
straight strokes.
• Don’t wipe the disc surface using circular strokes.
45
En
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Additional Information
Glossary
Aspect ratio
The width of a TV screen relative to its height. Conven-
tional TVs are 4:3 (in other words, the screen is almost
square); widescreen models are 16:9 (the screen is
almost twice as wide as it is high).
Chapter
Just as a book is split up into several chapters, a title on
a DVD disc is usually divided into chapters. See also
Title.
Dolby Digital
A surround sound system developed by Dolby Laborato-
ries containing up to six channels of digital audio
(front left and right, surround left and right, center and
low-frequency channels). See also DTS.
DTS
A surround sound system developed by Digital Theater
Systems as an alternative to Dolby Digital. DTS discs
contain up to eight channels of digital audio. See also
Dolby Digital.
MPEG video
The video format used for Video CDs and DVDs. Video
CD uses the older MPEG-1 standard, while DVD uses the
newer and much better quality MPEG-2 standard.
PBC (PlayBack Control) (Video CD only)
A system of navigating a Video CD through on-screen
menus recorded onto the disc. Especially good for discs
that you would normally not watch from beginning to
end all at once—karaoke discs, for example.
Regions (DVD only)
These associate discs and players with particular areas
of the world. This unit will only play discs that have
compatible region codes. You can find the region code
of your unit by looking on the rear panel. Some discs
are compatible with more than one region (or all
regions).
Title (DVD only)
A collection of chapters on a DVD disc. See also Chapter.
46
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
12
Language code list
Language/Langue
Japanese/japonais ( ja )
Code
1001
Language/Langue
Hausa ( ha )
Code
0801
Language/Langue
Quechua ( qu )
Code
1721
English/anglais ( en )
French ( fr)
0514
0618
0405
0920
0519
1412
1821
2608
1115
Rhaeto-Romance ( rm )
Kirundi ( rn )
Romanian ( ro )
Kinyarwanda ( rw )
Sanskrit ( sa )
Sindhi ( sd )
1813
1814
1815
1823
1901
1904
1907
1908
1909
1911
1912
1913
1914
1915
1917
1918
1919
1920
1921
1922
1923
2001
2005
2007
2008
2009
2011
2012
2014
2015
2018
2019
2020
2023
2111
Hindi ( hi )
0809
0818
0821
0825
0901
0905
0911
0914
0919
0923
1009
1023
1101
1111
Croatian (hr )
Hungarian ( hu )
Armenian ( hy )
Interlingua ( ia )
Interlingue ( ie )
Inupiak ( ik )
German ( de )
Italian ( it )
Spanish ( es )
Dutch ( nl )
Russian ( ru )
Chinese ( zh )
Korean ( ko )
Greek ( el )
Sangho ( sg )
Serbo-Croatian ( sh )
Singhalese ( si )
Slovak ( sk )
Indonesian ( in )
Icelandic ( is )
Hebrew ( iw )
Yiddish ( ji )
0512
0101
0102
0106
0113
Afar ( aa )
Slovenian ( sl )
Samoan ( sm )
Shona ( sn )
Abkhazian ( ab )
Afrikaans ( af )
Amharic ( am )
Arabic ( ar )
Javanese ( jw )
Georgian ( ka )
Kazakh ( kk )
Somali ( so )
Albanian ( sq )
Serbian ( sr )
Siswati ( ss )
Sesotho ( st )
Sundanese ( su )
Swedish ( sv )
Swahili ( sw )
Tamil ( ta )
0118
Greenlandic ( kl )
Cambodian ( km )
Kannada ( kn )
Kashmiri ( ks )
Kurdish ( ku )
Kirghiz ( ky )
1112
Assamese ( as )
Aymara ( ay )
Azerbaijani ( az )
Bashkir ( ba )
Byelorussian ( be )
Bulgarian ( bg )
Bihari ( bh )
0119
1113
0125
0126
0201
0205
0207
0208
0209
0214
0215
0218
0301
0315
0319
0325
0401
0426
0515
0520
0521
0601
0609
0610
0615
0625
0701
0704
0712
0714
0721
1114
1119
1121
1125
1201
1214
1215
1220
1222
1307
1309
1311
1312
1314
1315
1318
1319
1320
1325
1401
1405
1415
1503
1513
1518
1601
1612
1619
1620
Latin ( la )
Lingala (ln )
Bislama ( bi )
Bengali ( bn )
Tibetan ( bo )
Breton ( br )
Catalan ( ca )
Corsican ( co )
Czech ( cs )
Telugu ( te )
Laothian ( lo )
Lithuanian ( lt )
Latvian ( lv )
Tajik ( tg )
Thai ( th )
Tigrinya ( ti )
Turkmen ( tk )
Tagalog ( tl )
Setswana ( tn )
Tonga ( to )
Malagasy ( mg )
Maori ( mi )
Macedonian ( mk )
Malayalam ( ml )
Mongolian ( mn )
Moldavian ( mo )
Marathi ( mr )
Malay ( ms )
Welsh ( cy )
Danish ( da )
Bhutani ( dz )
Esperanto ( eo )
Estonian ( et )
Basque ( eu )
Persian ( fa )
Finnish ( fi )
Turkish ( tr )
Tsonga ( ts )
Tatar ( tt )
Twi ( tw )
Maltese ( mt )
Burmese ( my )
Nauru ( na )
Ukrainian ( uk )
Urdu ( ur )
2118
Uzbek ( uz )
2126
2209
2215
2315
2408
2515
2621
Nepali ( ne )
Fiji ( fj )
Vietnamese ( vi )
Volapük ( vo )
Wolof ( wo )
Xhosa ( xh )
Norwegian ( no )
Occitan ( oc )
Oromo ( om )
Oriya ( or )
Faroese ( fo )
Frisian ( fy )
Irish ( ga )
Scots-Gaelic ( gd )
Galician ( gl )
Guarani ( gn )
Gujarati ( gu )
Yoruba ( yo )
Zulu ( zu )
Panjabi ( pa )
Polish ( pl )
Pashto, Pushto ( ps )
Portuguese ( pt )
47
En
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Additional Information
Troubleshooting
Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this
component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components
and electrical appliances being used. If the trouble cannot be rectified after checking the items below, ask your nearest
Pioneer authorized service center or your dealer to carry out repair work.
Problem
Remedy
CDs, DVDs and Video CDs
The disc is ejected automati-
cally after loading.
•
Check that the disc is clean and undamaged (page 45).
Make sure that the disc is seated properly in the disc guide.
Check that the disc has a compatible region number (page 7).
There may be condensation inside the unit. Allow time for condensation to evaporate.
•
•
•
Avoid using the player near an air-conditioning unit.
Playback is not possible.
mark appears on screen.
•
•
Check that the disc is loaded correctly (label side face up).
The operation is prohibited by the system.
mark appears on screen.
•
•
The selected function does not operate for that disc.
When making changes in the
There is a CD or Video CD loaded and the setting that was changed applies only to
Setup OSD menus,
displayed.
is
DVD discs. The settings will take effect next time a DVD is loaded.
Picture playback stops and
the operation buttons cannot
be used.
•
Switch the power off once, then on again using the front panel standby/on switch.
New settings made in the
Setup screen menus while a
disc is playing are ineffective.
•
Some settings can be changed while a disc is playing, but are not effective until the
disc is stopped then restarted. This is not a malfunction. Note that making settings in the
Setup screen menus may cancel the resume function.
Settings are canceled.
No picture/No color.
•
If the power was cut due to power failure or by unplugging the power cord, settings
will be canceled.
•
•
Check that the video connections are correct and that plugs are inserted fully.
Check that the TV/monitor settings are correct.
Screen is stretched or aspect
does not change.
•
Make sure that the TV Screen option in the Setup menu matches the TV/monitor
you're using.
Picture disturbance during
playback or screen is dark.
•
This player is compatible with Macro-Vision System copy guard. Some discs include a
copy prevention signal, and when this type of disc is played back, stripes etc., may appear
on some sections of the picture depending on the TV. This is not a malfunction.
•
Problems with some discs may result in the screen becoming black for a brief instant
or shaking slightly when certain functions are executed.
Due to copy protection, connection of this system through a VCR or an AV selector
may prevent recording or cause picture problems. This is not a malfunction.
•
48
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
12
Problem
Remedy
Noticeable difference in DVD
and CD volume.
•
DVDs and CDs use different recording methods. This is not a malfunction.
Tuner
Noisy radio reception
•
•
Check that the frequency is correct.
Check that the antennas are connected properly. For FM, make sure that the antenna
is fully extended and positioned to give the best reception.
For AM, make sure that the loop antenna is pointing in the best direction.
•
If the radio signal is weak, an outdoor antenna will usually give better results than the
supplied indoor types.
Other electrical equipment, such as TVs, fluorescent lamps and motors can cause
interference. Try switching off or moving the equipment, or moving the antenna(s).
The tuning interval may be incorrect for your country or region. Try switching the
tuning interval (page 44).
•
•
Auto tuning does not pick up
some stations.
•
Auto tuning will only detect radio stations with a good signal. For more sensitive
tuning, connect an outdoor antenna.
General
The remote control doesn't
seem to work.
•
Make sure that you’re using the remote within its operating range and that there are
no obstacles between the remote and the sensor on the main unit.
•
Check that the batteries are not exhausted.
No audio, or audio is dis-
torted.
•
•
•
•
•
Check that the correct function is selected (DVD/CD, etc.), the volume turned up.
Check that the MUTE function is not on and that the disc is not paused.
Check that the disc is clean and undamaged (page 45).
Check that all rear panel connections are correct.
If you find dirty or oxidized plugs/terminals, clean them.
Can’t adjust sound mode
settings (bass, treble, etc.)
•
The Record Mode is switched on. Switch off then adjust as desired (see page 25).
Static electricity or other external influences may cause malfunctioning of this unit. In this case, unplug the power cord
and then plug back in. This will usually reset the unit for proper operation. If this does not correct the problem, please
consult your nearest PIONEER service center.
49
En
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Additional Information
Screen sizes and disc formats
The table below shows the effect of various TV Screen
settings on the different kinds of disc available.
When viewing a standard size TV or monitor
Setting and appearance Screen format of disc
When viewing a widescreen TV or monitor
Setting and appearance
Screen format of disc
Standard (TV programs, etc)
The program is presented
correctly, regardless of the
setting.
Widescreen (movies, etc.)
Note that some extra-wide
formats (such as CinemaScope)
will appear with black bars at the
top and bottom of the screen.
16:9 (Wide)
Any setting
Widescreen (movies, etc.)
The program is shown in
widescreen with black bars at
the top and bottom of the
screen.
Standard (TV programs, etc.)
Your TV will determine how the
picture is presentedcheck the
manual that came with the TV
for details. Typical options are
black bars either side, some
form of stretched or zoomed
presentation.
4:3 (Letter Box)
4:3 (Pan & Scan)
16:9 (Wide)
Widescreen (movies, etc.)
The sides of the program are
cropped so that the picture fills
the whole screen.
16:9 (Wide)
Widescreen (movies, etc.)
The program appears squashed:
set to either 4:3 (Letter Box) or
4:3 (Pan & Scan).
50
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
12
Speaker system (S-HTD1)
(Front Speaker x 2, Rear Speaker x 2, Center Speaker x 1,
Subwoofer x 1)
Specifications
Amplifier Section
Continuous power output (RMS)
Front speaker
Enclosure .................................... Closed-box bookshelf type
(magnetically shielded †)
System................................................... 10 cm 2-way system
Speaker
Front ................................................. 80 W, per channel
(1 kHz, 10 % T.H.D., 8 Ω)
Rear .................................................. 30 W, per channel
(1 kHz, 10 % T.H.D., 8 Ω)
Center............................................... 30 W, per channel
(1 kHz, 10 % T.H.D., 8 Ω)
Woofer ................................................. 10 cm cone type
Tweeter .............................................. 5.2 cm cone type
Nominal impedance ........................................................ 8 Ω
Frequency range ........................................ 50 to 20,000 Hz
Max. input ................................................................... 100 W
Dimensions ...................... 150 (W) x 270 (H) x 178 (D) mm
Weight ........................................................................... 2.0 kg
Subwoofer .................. 80W (100Hz, 10% T.H.D., 8Ω)
DVD Player (Audio)Section
S/N ratio ........................................................... 115 dB (EIAJ)
Dynamic range ................................................. 100 dB (EIAJ)
Distortion ................................................................. 0.004%
Frequency response
Rear speaker
Enclosure .................................... Closed-box bookshelf type
System.................................................. 8.7 cm 1-way system
Speaker .................................................. 8.7 cm (cone type)
Nominal impedance ........................................................ 8 Ω
Frequency range ...................................... 120 to 20,000 Hz
Max. input ..................................................................... 33 W
Dimensions ......................... 115 (W) x 150 (H) x 96 (D) mm
Weight ........................................................................... 0.8 kg
48 kHz sampling .................................. 4 Hz to 22 kHz
96 kHz sampling .................................. 4 Hz to 44 kHz
Wow & flutter ................................. Below measurable levels
( 0.001% W.PEAK)
DVD Player (Video) Section
Output level ................................................... 1 Vp-p (75 Ω)
Video Y output level ...................................... 1 Vp-p (75 Ω)
Video C output level............................... 286 mVp-p (75 Ω)
Center speaker
Enclosure .................................... Closed-box bookshelf type
(magnetically shielded †)
System.................................................. 8.7 cm 1-way system
Speaker ................................................. 8.7 cm (cone type)
Nominal impedance ........................................................ 8 Ω
Frequency range ........................................ 80 to 20,000 Hz
Max. input ..................................................................... 34 W
Dimensions ...................... 370 (W) x 120 (H) x 130 (D) mm
Weight ........................................................................... 1.8 kg
DVD (Other jacks) Section
Digital coaxial input (PCM/2/DTS)...... Coaxial connector
Tuner Section
FM tuner
Frequency range.................... 87.5 MHz to 108.0 MHz
Antenna ............................................. 75 Ω unbalanced
AM tuner
Subwoofer
Frequency range
Enclosure .............................................. Bass reflex floor type
System.................................................. 16 cm 1-way system
Speaker ................................................... 16 cm (cone type)
Nominal impedance ........................................................ 8 Ω
Frequency range ...................................... 30 Hz to 2000 Hz
Max. input ................................................................... 100 W
Dimensions ..................... 190 (W) x 360 (H) x 327 (D) mm
Weight ........................................................................... 4.8 kg
............................ 531 kHz to 1,602 kHz (9 kHz step)
........................ 530 kHz to 1,700 kHz (10 kHz step)
Antenna ................................. loop antenna (supplied)
Power Supply Section
Power Requirements
Multi voltage model
.................. AC 110-127/220-230/240 V (Switchable)
, 50/60 Hz
European model ................... AC 220-230 V, 50/60 Hz
UK model ..................................... AC 230 V, 50/60 Hz
Australian and New Zealand models
...................................................... AC 240 V, 50/60 Hz
†
Antimagnetic design (EIAJ) speaker system conforms to the basic
EIAJ standards.
Supplied Items
Remote control .................................................................... 1
AA/R6P dry cell batteries ................................................... 2
AM loop antenna ................................................................. 1
FM antenna .......................................................................... 1
Video cord (yellow) ............................................................. 1
Power cord ............................................................................ 1
................ 2 (Central and South America models only)
Speaker cords
Power consumption
Flat blade 2-pin AC plug model ......................... 540 W
Australian and New Zealand models .................. 139 W
Except Flat blade 2-pin AC plug model and
Australian and New Zealand models ................ 136 W
Power consumption in standby mode ............................ 1 W
5m (for front L-R speakers) ....................................... 2
2m (for center speaker) ............................................. 1
6m (for rear L-R speakers) ......................................... 2
3m (for subwoofer) ................................................... 1
Operating instructions ........................................................ 1
Warranty card (European and Australian models only) .... 1
Miscellaneous
Dimensions
European model and UK mode
.............................. 420 (W) x 411.6 (D) x 150 (H) mm
Except European model and UK mode
.............................. 420 (W) x 410.4 (D) x 150 (H) mm
Weight ........................................................................... 9.8 kg
Power plug adapter (Central and South America models only) ....
1
Note: Specifications and design subject to possible modification
without notice, due improvements.
51
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the demo mode
on/off
When you first plug in this system the display shows a demo
sequence. The demo will also start if the system is on in the
DVD function but idle for more than 5 minutes. The demo
will stop if you press any button except CD MODE on the
main unit .
•
•
To switch the demo mode off completely,
press and hold CD MODE on the main unit
for about 3 seconds while the demo is in
progress.
To switch the demo mode on, press and hold
CD MODE on the main unit for about 3
seconds while the system is in standby.
Published by Pioneer Corporation.
Copyright © 2001 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS [USA] INC.
PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 9586-6300
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A.
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
San Lorenzo 1009 3er Piso Desp. 302 Col. Del Valle Mexico D.F. C.P. 03100
TEL: 5-688-52-90
<XRB3006-A>
<TSWZW/01C00001>
Printed in
Download from Www.Somanuals.com. All Manuals Search And Download.
|