TSU
3000
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety & Regulations
FCC Compliancy
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rule. These limits are designed to
provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If the
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
■
■
■
■
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a different circuit from the receiver.
Consult the dealer or an experienced radio/TV technician for help.
FCC Information for User
Caution The user changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
© 2004 Royal Philips Electronics NV
All rights are reserved. Reproduction in whole or in part is prohibited without prior
consent of the copyright owner.
User Guide
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Taking a First Look
4
4
5
7
8
Pronto NG: The Home Theater Control Panel
The Device
The Touch Screen
What’s New for Pronto Next Generation?
Before You Start
10
10
Placing the batteries
Getting Started
11
11
11
12
12
12
13
14
15
15
16
Turning on Pronto NG
Setting the Contrast
Setting Time and Date
Changing the Time Format
Changing the Time
Changing the Date
Setting the Language
Operating Pronto NG
Device Overview
Page Overview
Customizing Pronto NG
Using the Tools
17
17
18
21
23
26
28
29
30
30
31
31
32
32
33
33
Defining the Brand for a Device
Learning Commands
Labeling Elements
Adding Devices
Deleting Elements
Moving Devices
Adjusting the Settings
Setting the Timeout of the LCD Backlight
Setting the Timeout of the LCD Screen
Setting the Switch Level for the Backlight
Setting the Volume Level
Setting the Navigation for Pronto NG
Setting the Animation Mode
Calibrating the Touch Screen
User Guide
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Using the Power Features
Creating and Editing Macros
Creating a Macro
34
34
34
36
37
37
43
44
46
47
48
Editing a Macro
Creating and Editing Timers
Creating and Editing Timers
Activating Timers
Operating Pronto NG with the Cursor
Operating Pronto NG with RF
Selecting RF to Operate your Devices
Selecting IR to Operate your Devices
ProntoEdit NG
FAQ
49
51
Troubleshooting
53
53
54
55
55
55
General Problems
Customizing Problems
Memory Storage Problems
Pronto NG error messages
Connection to the PC
Maintaining Pronto NG
Important Notices
56
56
56
56
Cleaning Pronto NG
Upgrading Pronto NG
List of Symbols
Specifications
Glossary
57
60
61
64
Index
User Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking a First Look
Pronto NG:
The Home Theater Control Panel
Pronto NG is a Home Theater Control Panel that allows maximum flexibility and
customization for even the most sophisticated home entertainment system. It can
control almost any device that works with infrared (IR) remote control signals.
Its intuitive interface makes it a perfect remote control for every user.
Pronto NG is easy to configure. It contains a huge universal database where
IR codes are stored to control different brands for all kinds of video, audio devices
and even home automation equipment. By default Pronto NG is set up to control
Philips and Marantz devices. For other brands you simply choose the brands of
your devices when you use Pronto NG for the first time.
Pronto NG offers you some extra powerful features:
■
You can create and edit macros, allowing you to send a series of commands
with one single touch.
■
You can set timers for certain actions to be carried out at predefined times,
e.g. switching on your lights or recording your favorite daily TV-show with
your VCR.
■
You can choose to have Pronto NG working with radio frequency (RF) signals to
operate devices from a distance or from an adjacent room. To do this, you
need an optional RF Extender that converts Pronto NG RF signals into IR
signals.
With ProntoEdit NG software you can create your own screens and define a
personal look. ProntoEdit NG’s Online Help system (accessible via the ‘Help’ icon in
ProntoEdit NG) will guide you through the process.
See ‘ProntoEdit NG’ on page 49 for more information. You can find ProntoEdit NG
the Downloads section of the website you can also find the latest upgrades for
your Pronto NG software.
User Guide
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking a First Look
The Device
Pronto NG has several hard buttons. Most are freely programmable, some have a
predefined function:
■
The buttons on the left side of the Pronto NG screen have predefined
functions: Page up, Page down and Backlight.
■
The 4 firm keys below the touch screen are freely programmable. You can
reprogram the function of these buttons and change the label on the touch
screen.
■
■
The cursor and the OK and Home buttons on the right side of the cursor are
programmed to operate devices (e.g. navigating through the on screen menu of
your TV).
With the Toggle button you can change the working of the cursor.
The free programmable button is meant for future purposes.
The buttons on the right side of the screen are used to control the volume and
channel: Channel up, Channel down, Mute, Volume up and Volume
down. Although these buttons each have a predefined function, you can
program them yourself. If you learn one of these buttons or assign a macro to
it, its predefined function will be permanently lost.
Learning eye
Light sensor
LCD touch screen
Channel up
Channel down
Mute
Volume up
Volume down
Firm keys
Toggle button
Free programmable
OK
Home
Cursor
User Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking a First Look
Backlight
Page up
Page down
Reset button
Battery
compartment
Connection to docking station
USB port
User Guide
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking a First Look
The Touch Screen
Device
Page
Overview
button
Overview
button
Pronto NG Icon
Previous
Device
Next
Device
Soft
buttons
Labels for the
firm keys
User Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking a First Look
What’s New for Pronto Next Generation?
This new Pronto NG (TSU3000) offers several new features compared to the
previous model of Pronto (TSU2000). The most important ones are:
■
Light sensor
The light sensor on your Pronto NG causes the backlight to switch on
automatically according to the ambient light of your own home theater
environment.
■
Transparency
Pronto NG supports transparency in buttons and other objects. This makes it
easier to create complex user interfaces. You can now place buttons with a
transparent background on top of a background image and let transparent
buttons overlap.
■
16 gray scales
The number of gray scales has increased from 4 to 16. Therefore the buttons
look much more natural.
■
■
USB
Pronto NG has a USB port to make downloading and uploading easier.
4 MB of Memory
Pronto NG has 4 Megabyte of memory. This enables you to download larger
configuration files to Pronto NG.
■
■
Integrated Macros
Macros are now better integrated in the configuration file. Each button can be
a macro, this means each button can contain more than one action.
More advanced Timers
Your Pronto NG is able to set timers for certain actions to be carried out at any
time you choose. Timers are not an entirely new feature of Pronto NG, but they
are easier to use and better integrated with the configuration file. You can
activate and deactivate the timers you created and you can also set them to
repeat daily or weekly. For instance, you can have the lights switched on every
day at sunset. You can also create a timer to set your VCR to record your
favorite TV-show on Wednesday and Saturday.
RF
By default, Pronto NG operates your devices with IR signals. However, you can
choose to have Pronto NG working with radio frequency (RF) signals to operate
devices from a distance or from an adjacent room. An RF Extender (not
included) is therefore required.
■
■
Page Overview
The Page Overview offers you a list of all the pages for one device. Every
device comes with a Page Overview, making it easier and faster to browse
through the device pages.
User Guide
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking a First Look
■
Cursor Navigation
By default the cursor is programmed to operate devices. The functions
assigned to the cursor button depend on the device active on Pronto NG.
Pronto NG also offers you the possibility to use the cursor for navigating
through devices and pages on the screen. The Left and Right cursor buttons
allow you to scroll through the devices, with the Up and Down cursor buttons
you scroll through the different pages.
■
■
Animation Mode
Pronto NG provides navigation feedback through graphical animations of mode
transitions and page transitions. You can enable and disable the animations of
your Pronto NG in the Settings Pages.
Multi Language Support
Pronto NG now supports besides English also Spanish, French, German and
Dutch.
User Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Placing the Batteries
When you use Pronto for the first time, you will have to place 4 AAA batteries. You
can use rechargeable or non-rechargeable AAA batteries.
1
2
Press the latch on the battery cover with your thumb and then slide the
cover forward firmly.
Lift up the battery cover.
3
4
Place the batteries in the battery
compartment.
Slide the battery cover back on.
After a few seconds, the Pronto NG starts up automatically and an
introduction screen appears. The Pronto NG beeps twice to indicate
that it has finished starting up.
Notes When the batteries are running low, the Low Battery icon appears over the battery
icon in the upper left corner of the screen.
Pronto NG retains all its settings when the batteries have run out. You will only
have to set the contrast and the time. See ‘Setting the Contrast’ on page 11 and
‘Changing the Time’ on page 12 for more information.
You can also use a docking station and a battery pack to recharge your Pronto NG.
The docking station and the battery pack are optional.
User Guide
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Turning on Pronto NG
Pronto NG can be turned on in three different ways:
Tap the touch screen.
Note
Only use your finger, a stylus or a blunt soft object like a pencil eraser to
operate the touch screen.
Press one of the 4 firm keys below the screen to activate the display.
Note
When you press a hard button on Pronto NG, the according function will be
executed immediately, while the 4 firm keys below the touch screen will
activate the display.
Press the Backlight button.
Setting the Contrast
You can set the contrast level and switch on the backlight of Pronto NG using the
hard buttons on the left side of the device.
■
To decrease the contrast, press and hold the Backlight button and at the
same time press the ‘-’ hard button.
To increase the contrast, press and hold the Backlight button and at the
same time press the ‘+’ hard button.
■
To switch on the backlight, press the Backlight button.
Backlight
& contrast
+
-
User Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Setting Time and Date
When you have placed the batteries and turned on Pronto NG, you have to set the
current time.
Attention Every time you reset your Pronto NG you will have to set the time again.
Changing the Time Format
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
2
Tap button in the Tools Menu.
The first Settings Page appears.
3
4
Tap the Time Format button
The Time Format button toggles between the three time formats:
in the first Settings Page.
■
■
■
12 hour (AM/PM): This is the default format;
24 hour;
No time.
Tap the Pronto NG icon
to exit the Settings Tool.
Changing the Time
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The first Settings Page appears.
Tap the Time button in the first Settings Page.
The Time button is selected. The labels ‘+’ and ‘-’ appear for the two middle
firm keys.
User Guide
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
4
To increase the time, press (and hold) the firm key labeled ‘+’.
-or-
To decrease the time, press (and hold) the firm key labeled ‘-’.
5
6
Tap the Time button again.
The new time is set.
Tap the Pronto NG icon
to exit the Settings Tool.
Changing the Date
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
2
Tap in the Tools Menu.
The first Settings Page appears.
To change the day
1
Tap the Day button in the first Settings Page.
The Day button is selected. The labels ‘+’ and ‘-’ appear for the two middle
firm keys.
2
To increase the days, press (and hold) the firm key labeled ‘+’.
-or-
To decrease the days, press (and hold) the firm key labeled ‘-’.
3
4
Tap the Day button again.
The new day is set.
When you have changed the date, tap the Pronto NG icon
the Settings Tool.
to exit
To change the month
1
Tap the Month button in the first Settings Page.
The Month button is selected. The labels ‘+’ and ‘-’ appear for the two middle
firm keys.
2
To increase the months, press (and hold) the firm key labeled ‘+’.
-or-
To decrease the months, press (and hold) the firm key labeled ‘-’.
3
4
Tap the Month button again.
The new month is set.
When you have changed the date, tap the Pronto NG icon
the Settings Tool.
to exit
User Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
To change the year
1
Tap the Year button in the first Settings Page.
The Year button is selected. The labels ‘+’ and ‘-’ appear for the two middle
firm keys.
2
To increase the years, press (and hold) the firm key labeled ‘+’.
-or-
To decrease the years, press (and hold) the firm key labeled ‘-’.
3
4
Tap the Year button again.
The new year is set.
When you have changed the date, tap the Pronto NG icon
the Settings Tool.
to exit
Setting the Language
You can change the language used on your Pronto NG.
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The first Settings Page appears.
Press the Page down hard button.
The second Settings Page appears.
4
5
Tap
in the second Settings Page.
The Language button toggles between five languages:
■
■
■
■
■
English;
German;
French;
Dutch;
Spanish.
Tap the Pronto NG icon
to exit the Settings Tool.
User Guide
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Operating Pronto NG
Pronto NG contains a series of customizable devices, each consisting of several
device pages. All active devices on your Pronto NG are listed in the Device
Overview. All the available device pages are listed per device in the Page
Overview.
Device Overview
The Device Overview offers you a list of all the devices you can control with
Pronto NG. To view the Device Overview, press the Device Overview button at
the top of the touch screen.
Device Overview
button
Device Left
button
Device Right
button
You can navigate between the devices in two different ways:
■
Tap the device you want to operate from the Device Overview.
■
Tap the Device Left button
at the top of the touch screen to navigate to
the previous device.
Tap the Device Right button
at the top of the touch screen to navigate
to the next device.
By default you navigate through Pronto NG, using this touch screen navigation.
When cursor navigation is enabled, the Device Left and Device Right button
disappear and the Cursor Navigation icon
appears at the top left. You then
navigate through the devices and pages using the cursor. For more information on
changing the touch screen navigation to cursor navigation, see ‘Operating
Pronto NG with the Cursor’ on page 44.
User Guide
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Page Overview
The Page Overview offers you a list of all the pages for one device. To view the
Page Overview, tap the Page Overview button, that displays the page number in
the upper area of the touch screen.
Page
Overview
button
You can navigate between the different pages in two different ways:
■
■
Tap the page you want to operate from the Page Overview.
Press the Page Up or Page Down hard button on the left side of
Pronto NG.
User Guide
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
What makes Pronto NG so powerful, is the ability to extend its functionality in
multiple ways, like programming additional functions, adding supplementary
devices and changing the interface as it suits you best.
For full editing you can use ProntoEdit NG software. See ‘ProntoEdit NG’ on page
49 for more information.
Using the Tools
Pronto NG provides different tools. For customizing Pronto NG you have to switch
to the appropriate tool. Pronto NG offers 10 different tools in the Tools Menu, each
providing different functionalities:
Settings Tool:
Defining the settings of your Pronto
NG (p. 30)
Timer Tool:
Defining timer actions to be carried
out at predefined times (p. 37)
Brand Tool:
Defining the brands of your
audio/video equipment (p. 18)
Learn Tool:
Learning IR codes from other remote
controls (p. 21)
Label Tool:
Labeling buttons, devices and
pages (p. 23)
Add Tool:
Adding new devices or copying
existing devices (p. 26)
Delete Tool:
Deleting button actions or devices
(p. 28)
Move Tool:
Moving devices in the Device
Overview (p. 29)
Macro Tool:
Programming a sequence of
commands for one single button
(p. 34)
RF IR Tool:
Defining to operate Pronto NG with
IR signals or RF signals
(p. 46)
To enter the Tools Menu, you have to tap and hold the Pronto NG icon
in the
upper left corner of the touch screen for 3 seconds.
You can exit all Tools by tapping the Pronto NG icon
.
Keep in mind that your latest changes to the current page will not be saved
automatically.
User Guide
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
In general, in the Tools:
■
■
■
Tap
Tap
Tap
Tap
to start using the Tool.
to go back to the Tools Menu.
to confirm an action and save the changes you made.
to cancel an action without saving the changes.
■
■
Press the firm key labeled
the Tools Menu.
to end a series of actions and go back to
Defining the Brand for a Device
Pronto NG contains a huge list of brands and their corresponding IR codes in its
database. Pronto NG uses these IR codes to control devices. Because there are
several brands using specific IR codes, you have to define the brands and the
corresponding code sets for each device. You can either have Pronto NG
autosearch the brand or select it yourself. If a device’s brand contains more than
one IR code set, you also have to select it.
On the Device Overview you find buttons for the most common video and audio
devices. Pronto NG is set by default to operate Philips and Marantz devices. For all
devices other than Philips or Marantz, you first have to define the brand before you
can operate them with Pronto NG.
Selecting the Brand and Code Set for your Device
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
The Tools Menu appears.
in the upper left corner of the
2
3
4
Tap
in the Tools Menu.
The ‘Brand Tool’ screen appears.
Tap
in the ‘Brand Tool’ screen.
The Device Overview appears.
In the Device Overview, tap the Device for which you want to define
the brand.
A message screen appears.
5
Tap
.
The ‘Brands’ screen appears.
User Guide
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Selecting the brand
1
Tap the Scroll Down button
Brands list.
or the Scroll Up button
next to the
The Brands list scrolls down/up.
Note
You can also select the brand via the virtual keyboard by tapping one or more
of the brand’s name characters.
2
3
Tap the brand for the selected Device in the Brands list.
Tap in the ‘Brands’ screen.
If there is only one code set, the ‘Installing the Brand’ screen appears.
Go to ‘Installing the brand’ below.
-or-
If there is more than one possible code set, a message screen appears.
4
Tap
.
The ‘Code sets’ screen appears.
Selecting the code set
1
If necessary, tap the Scroll Down button
Scroll Up button next to the Code Sets list.
The Code Sets list scrolls down/up.
Tap the code set for the selected Device in the Code Sets list.
Tap in the ‘Code Sets’ screen.
The ‘Installing the Brand’ screen appears.
or the
2
3
Installing the brand
1
Tap
in the ‘Installing the Brand’ screen.
The first Page of the selected Device appears.
2
3
Tap different buttons to see if the device is responding to the IR codes
for the selected brand and code set.
Press the left firm key, labeled
.
The ‘Installing the Brand’ screen appears again.
4
Tap in the ‘Installing the Brand’ screen.
The IR codes for the selected brand and code set are installed.
User Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Selecting the Brand and searching the Code Set for your device
Note
Make sure the device for which you are searching the brand is turned on.
1
2
3
4
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The ‘Brand Tool’ screen appears.
Tap
in the ‘Brand Tool’ screen.
The Device Overview appears.
In the Device Overview, tap the Device for which you want to define
the brand.
A message screen appears.
5
6
Tap
.
The ‘Brands’ screen appears.
Select the brand of your device as described in ‘Selecting the brand’
on page 19.
Searching the code set
1
Tap
in the ‘Code Sets’ screen.
The ‘Searching the Code Set’ screen appears.
2
Tap and point Pronto NG at the device.
The ‘Searching’ screen appears. Pronto NG searches through the list of code
sets for the selected brand, by sending out an IR code for each code set.
3
4
When the device for which you are defining the brand, turns off,
tap
in the ‘Searching’ screen.
The ‘Installing the Brand’ screen appears.
To install the brand and code set, follow the instructions described in
‘Installing the brand’ on page 19.
Searching the Brand and Code Set for your device
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The ‘Brand Tool’ screen appears.
Tap
in the ‘Brand Tool’ screen.
The Device Overview appears.
User Guide
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
4
5
In the Device Overview, tap the Device for which you want to define
the brand.
A message screen appears.
Tap
.
The ‘Brands’ screen appears.
Searching the brand
1
Tap
in the ‘Brands’ screen.
The ‘Searching the Brand’ screen appears.
2
Tap
and point Pronto NG at the device.
The ‘Searching’ screen appears. Pronto NG searches through the list of brands,
by sending out an IR code for each brand.
3
4
When the device for which you are defining the brand, turns off,
tap
in the ‘Searching’ screen.
The ‘Installing the Brand’ screen appears.
To install the brand and code set, follow the instructions described in
‘Installing the brand’ on page 19.
Learning Commands
If an IR code is not in the database, you can program Pronto NG commands by
transmitting IR signals from your existing remote control to Pronto NG’s learning
eye.
The Learn Tool allows you to learn a button
or a device action. A device action is an
action that is executed automatically when
you select a device. E.g. when you select TV,
your Pronto NG can learn to switch on the TV
at the same time. You can also use the Learn
Tool to relearn commands that do not work
properly.
4 - 8 inches
10 - 20 cm
Learning
eye
Note
Changing the Brand in the Brand Tool
will not have an impact on the learned
codes.
User Guide
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Learning a Button
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
The Tools Menu appears.
in the upper left corner of the
2
3
Tap
in the Tools Menu.
The ‘Learn Tool’ screen appears.
Tap
.
The last page you have visited appears.
4
5
Navigate to the Device and the Page that contains the button you want
to learn.
Position Pronto NG and the remote control as illustrated above.
Note
Make sure that you aim Pronto NG’s learning eye at the remote control’s
IR window.
The distance between Pronto NG and the remote control should be between
4 and 8 inches (10 and 20 cm).
6
7
Tap the button you want to learn.
A Learning indication appears in the upper right corner of the touch screen.
Press and hold the key on the other remote control for 1 second.
Make sure you press the key within 5 seconds.
If learning succeeded, you will get an OK message.
If learning failed, you will get a Failure message.
See ‘Pronto NG will not learn commands’ on page 54 for more information.
8
9
When you want Pronto NG to learn other buttons, repeat steps
6 and 7.
Press the left firm key labeled
stop learning.
below the touch screen to
Learning a Device Action
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
The Tools Menu appears.
in the upper left corner of the
2
3
Tap
in the Tools Menu.
The ‘Learn Tool’ screen appears.
Tap
.
The Device Overview appears.
User Guide
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
4
Position Pronto NG and the remote control as illustrated above.
Note
Make sure that you aim Pronto NG’s learning eye at the remote control’s
IR window.
The distance between Pronto NG and the remote control should be between
4 and 8 inches (10 and 20 cm).
5
6
Tap the Device for which you want to learn a Device Action.
A Learning indication appears in the upper right corner of the touch screen.
Press and hold the key on the other remote control for 1 second.
Make sure you press the key within 5 seconds.
If learning succeeded, you will get an OK message.
If learning failed, you will get a Failure message.
See ‘Pronto NG will not learn commands’ on page 54 for more information.
7
8
When you want Pronto NG to learn other device actions, repeat steps
5 and 6.
Press the left firm key labeled
stop learning.
below the touch screen to
Labeling Elements
The Label Tool allows you to label a button, a device or a page. In the Label Tool
you can find a virtual keyboard. This keyboard zooms in when you tap a character.
The keyboard contains four different character sets, including a series of symbols
you can use for labeling. You use the Shift button to switch between the four
character sets on the keyboard.
For a complete list of the symbols, see ‘List of Symbols’ on page 57.
User Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Labeling a Button
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap
in the Tools Menu.
The ‘Label Tool’ screen appears.
Tap
.
The page you last visited appears.
4
5
Navigate to the Device and the Page that contains the button you want
to label.
Tap the button you want to label.
The ‘Labeling’ screen appears.
6
7
Tap the keyboard.
The keyboard zooms in.
Tap the character you want to add to the label.
The character is added to the label. The keyboard automatically zooms out
again.
To zoom out without adding a character to the label, press
.
The character is not added to the label. The keyboard is zoomed out.
To use other characters and symbols, press
.
The character set on the keyboard switches.
You can choose from four different character sets.
To remove characters, press the firm key labeled
.
The character in front of the cursor is removed.
8
9
You can add other characters to the label.
Tap
.
The label of the selected button is changed. The last visited page appears
again.
-or-
Tap
.
The last visited page appears again, without changing the label of the selected
button.
10 You can select other buttons on Pronto NG to label.
11 Press the left firm key labeled
the Label Tool.
below the touch screen to exit
User Guide
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Labeling a Device
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
in the upper left corner of the
The Tools Menu appears.
2
3
4
Tap
in the Tools Menu.
The ‘Label Tool’ screen appears.
Tap
.
The Device Overview appears.
Tap the Device you want to label.
The ‘Labeling’ screen appears.
5
6
Follow the instructions 6 to 8 of ‘Labeling a Button’ on page 24.
Tap
The label of the selected Device is changed. The Device Overview appears
again.
.
-or-
Tap
.
The Device Overview appears again, without changing the label of the
selected device.
7
8
You can select other Devices in the Device Overview to label.
Press the left firm key labeled
the Label Tool.
below the touch screen to exit
Labeling a Page
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
The Tools Menu appears.
in the upper left corner of the
2
3
4
5
Tap
in the Tools Menu.
The ‘Label Tool’ screen appears.
Tap
in the ‘Label Tool’ screen.
The Page Overview appears.
Tap the Page you want to label.
The ‘Labeling’ screen appears.
Follow the instructions 6 to 8 of ‘Labeling a Button’ on page 24.
User Guide
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
6
Tap
.
The label of the selected Page is changed. The Page Overview appears again.
-or-
Tap
.
The Page Overview appears again, without changing the label of the selected
page.
7
8
You can select another Page in the Page Overview to label.
Press the left firm key labeled
the Label Tool.
below the touch screen to exit
Adding Devices
The Add Tool allows you to add a new device or copy an existing device.
When you add a new device, a device template stored on your Pronto NG is used
to create the device pages, buttons and functions. By default Philips IR codes are
used when you add a new device. For your brand of device, you then have to
program the new device using the Brand Tool (page 20) or the Learn Tool (page 23).
Copying an existing device saves time. The personal settings you defined for that
device will also be copied.
For instance, if you want to add a second VCR player, you do not have to define the
brand, learn or create macros again. You can just copy them from the existing VCR
player already programmed on your Pronto NG.
Adding a New Device
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
The Tools Menu appears.
in the upper left corner of the
2
3
4
5
Tap
in the Tools Menu.
The ‘Add Tool’ screen appears.
Tap
in the ‘Add Tool’ screen.
The ‘Adding’ screen appears.
Tap the device template you want to add in the Device Templates list.
The ‘IR Code’ screen appears.
Tap
The ‘Actions’ screen appears.
.
User Guide
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
6
Tap
in the ’Actions’ screen.
The Device is added to Pronto NG with its actions like IR codes, beeps and
delays.
-or-
Tap
in the ‘Actions’ screen.
The Device is added to Pronto NG without its actions like IR codes, beeps and
delays. To operate this device, you have to learn every button of the device
with the Learn Tool.
7
Tap
.
The Device is added and the Tools Menu appears again.
Note
Added devices are automatically positioned at the end of the Device Overview.
You can move devices with the Move Tool. See ‘Moving Devices’ on page 29 for
more information.
Copying an Existing Device
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
The Tools Menu appears.
in the upper left corner of the
2
3
4
5
6
Tap
in the Tools Menu.
The ‘Add Tool’ screen appears.
Tap
in the ‘Add Tool’ screen.
The ‘Adding’ screen appears.
Tap the Device you want to copy in the Devices list.
The ‘IR Code’ screen appears.
Tap
.
The ‘Actions’ screen appears.
Tap
in the ‘Actions’ screen.
The Device is copied to Pronto NG with its actions like IR codes, beeps and
delays.
-or-
Tap
in the ‘Actions’ screen.
The Device is copied to Pronto NG without its actions like IR codes, beeps and
delays. To operate this device, you have to learn every button of the device
with the Learn Tool.
User Guide
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
7
Tap
.
The Device is added and the Tools Menu appears again.
Note
Added devices are automatically positioned at the end of the Device Overview.
You can move devices with the Move Tool. See ‘Moving Devices’ on page 29 for
more information.
Deleting Elements
The Delete Tool allows you to delete a button or a device.
Deleting a Button
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap
in the Tools Menu.
The ‘Delete Tool’ screen appears.
Tap
.
The last visited page on the Pronto NG appears.
4
5
Navigate to the Device and the Page that contains the button you want
to delete.
Tap the button you want to delete.
A message screen appears.
6
7
Tap
.
The button is deleted.
You can select other buttons on Pronto NG to delete.
-or-
Press the right firm key labeled
to undo the deletion.
The button is restored.
8
Press the left firm key labeled
the Delete Tool.
below the touch screen to exit
User Guide
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Deleting a Device
1
2
3
4
5
6
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap
in the Tools Menu.
The ‘Delete Tool’ screen appears.
Tap
.
The Device Overview appears.
Tap the Device you want to delete.
A message screen appears.
Tap
.
The Device is deleted.
You can select other Devices on Pronto NG to delete.
-or-
Press the right firm key labeled
to undo the deletion.
The Device is restored.
7
Press the left firm key labeled
the Delete Tool.
below the touch screen to exit
Moving Devices
The Move Tool allows you to move a device up or down the Device Overview,
enabling you to put your most used devices at the top of the list.
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
2
Tap in the Tools Menu.
The ‘Move Tool’ screen appears.
3
4
Tap the Device you want to move in the Devices list.
Tap the Move Up
in the ‘Moving’ screen.
The selected Device moves up/down in the Device List.
or Move Down
button below the Devices list
5
Tap in the ‘Moving’ screen.
The Device is moved.
User Guide
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Adjusting the Settings
In the Settings Pages you can adjust several settings. You can:
■
■
■
■
■
■
■
■
■
Set the time and date as described earlier, on page 12;
Set the timeout of the LCD backlight;
Set the timeout of the LCD screen;
Set the level of the light sensor;
Set the volume level;
Set the language of the Pronto NG, as described earlier, on page 14;
Set Pronto NG to operate with the Cursor;
Set the animation mode;
Calibrate the touch screen.
In the third Settings Page you can consult the version information and the
available memory.
1
2
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Select
.
The first Settings Page appears.
Setting the Timeout of the LCD Backlight
The timeout of the LCD backlight determines how long the backlight of the touch
screen and the buttons stays active. Shortening the active time will increase
Pronto’s battery life. The backlight timeout and the LCD screen timeout can work
independently.
1
Tap
in the first Settings Page.
The Backlight Timeout button is selected. The ‘+’ and ‘-’ labels appear on
User Guide
30
the two middle hard buttons below the touch screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
2
3
To increase the timeout, press (and hold) the button labeled ‘+’.
-or-
To decrease the timeout, press (and hold) the button labeled ‘-’.
Tap
again.
The new LCD backlight timeout is set.
Setting the Timeout of the LCD Screen
The timeout of the LCD screen determines how long the LCD touch screen stays
active before turning off. Shortening the active time will increase Pronto NG’s
battery life.
Note
The LCD screen will only time out when you are not using Pronto NG.
1
Tap
in the first Settings Page.
The LCD Timeout button is selected. The ‘+’ and ‘-’ labels appear on the two
middle firm keys below the touch screen.
2
3
To increase the timeout, press (and hold) the firm key labeled ‘+’.
-or-
To decrease the timeout, press (and hold) the firm key labeled ‘-’.
Tap
again.
The new LCD screen timeout is set.
Setting the Switch Level for the Backlight
You can set the backlight of your Pronto
to switch on or off according to the
ambient light of your home theater
environment.
Ambient light level
Threshold indicator
By positioning the threshold indicator
you define when the backlight switches on or off.
Setting the switch level
1
2
Tap
in the first Settings Page.
The Light level button is selected. The ‘+’ and ‘-’ labels appear on the two
middle hard buttons below the touch screen.
Press and hold the hard buttons labeled ‘+’ and ‘-’ to position the
indicator.
1
To set the switch level for a dark environment, position the
indicator at the right side of the light level bar.
The backlight will switch on even at a high ambient light level.
User Guide
31
2
To set the backlight always on, position the indicator at the far right.
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
3
To set the switch level for a bright environment, position the
indicator at the left side of the light level bar.
The backlight will switch on only in a dark environment.
4
To set the backlight always off, position the indicator at the far left.
3
Tap
again.
The Light Level button is deselected. The new level for the light sensor is set.
Note
The timeout of the LCD backlight also determines when the LCD backlight
switches on and off. Therefore, if you set the threshold to the left side of the light
level bar, the backlight does not switch off immediately.
Setting the Volume Level
You can set the volume level for the hard buttons as well as for the touch screen
buttons. The volume of the button refers to the loudness of the beep you hear
when you press or tap a button.
Setting the Volume Level of the Hard Buttons
To adjust the volume of the hard buttons, tap
Settings Page.
in the second
You can either select 1 of the 3 volume levels or choose to mute. Every time
you press, the volume level increases with one step up to level 3.
Setting the Volume Level of the Touch Screen
To adjust the volume level of the touch screen, tap
second Settings Page.
in the
You can either select 1 of the 3 volume levels or choose to mute. Every time
you tap, the volume level increases with one step up to level 3.
Setting the Navigation for Pronto NG
The cursor is used by default to operate your devices. You then navigate the Pronto
NG with the touch screen buttons. However, you can also set the cursor to browse
through Pronto NG’s devices and pages. For more information on operating the
Pronto NG with the cursor, see ‘Operating Pronto NG with the Cursor’ on page 44.
To set the navigation for the Pronto NG, tap
Settings Page:
in the second
■
You can select Cursor Navigation-Off to navigate the Pronto NG with the
touch screen buttons.
■
You can select Cursor Navigation-On to navigate the Pronto NG with the
cursor.
User Guide
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Pronto NG
Setting the Animation Mode
Pronto NG provides navigation feedback through graphical animations. Switching
pages is done with a page transition, switching from Use Mode to one of the Tools
is accompanied with a mode transition. You can enable and disable the animations
of your Pronto NG in the second Settings Page:
■
You can disable the animations by choosing ‘None’ (no animations). By
disabling all animations you use the absolute maximum of your Pronto NG’s
processing speed.
■
■
■
When changing pages with the ‘Page Only’ animation, one page seems to
slide out of the screen, while the second page slides in.
The ‘Mode Only’ animation shifts the Pronto NG icon at the top area of the
touch screen.
With the option ‘Full’ you can enable both animations at the same time.
Calibrating the Touch Screen
When you first use your Pronto NG, the touch screen is already calibrated.
However, if you notice that your Pronto NG does not send out the commands in
accordance with what is indicated on the touch screen, it is advised to recalibrate
the touch screen.
Attention Never use an actual pen, pencil or other sharp object on the touch screen. Use a
pointy object like a plastic-tipped pen or a stylus intended for use with touch
screens.
1
Tap
in the second Settings Page.
The ‘Calibration’ screen appears.
2
3
4
5
Tap the upper left corner on the touch screen.
Tap the lower right corner on the touch screen.
Tap the upper right corner on the touch screen.
Tap the lower left corner on the touch screen.
The touch screen is calibrated.
-or-
Press the middle firm key, labeled
.
The second Settings Page appears again without calibrating the touch screen.
Note
If the calibration fails, an message appears and you can follow the procedure to
calibrate the touch screen again.
User Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Creating and Editing Macros
A macro allows you to send a sequence of commands when tapping one single
button. You can for instance switch on your TV, turn on a movie channel and
prepare your VCR for recording by rewinding the videotape. The macro contains an
action list. The action list can be created and edited in the Macro Tool.
Note
Once you have programmed a macro, the button actions will not be changed when
you select another brand in the Brand Tool.
In the Macro Tool you first have to select the button, that will contain the macro,
also called the target button. Then, one by one, you create an action list by
adding actions to this target button. You can do this by:
■
Selecting another button and adding its actions to the action list of your
target button.
■
■
Adding a delay to the action list.
Adding a beep to the action list.
After creating the macro, all actions you added to the action list are executed
when you tap the button.
Creating a Macro
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The ‘Macro Tool’ screen appears.
Tap
in the ‘Macro Tool’ screen.
The last visited page appears.
4
5
Navigate to the Device and the Page that contains the target button
you want to use for a macro.
Tap the button you want to select as a target
button.
If you can use the button to program a macro,
the ‘Macro’ screen appears.
-or-
If you cannot use the button to program a
macro, you hear a Failure beep.
User Guide
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Note
You can assign a macro to most buttons of your Pronto NG.
The hard buttons on the left side of Pronto NG (Backlight, Page Up and Page
Down) are fixed.
The Toggle and Home button (around the cursor) can only be reprogrammed with
ProntoEdit NG.
Please refer to ‘ProntoEdit NG’ on page 49.
To add an action to the action list
1
2
3
Tap
in the ‘Macro’ screen.
The last visited page appears again.
Navigate to the Device and the Page that contains the button you want
to add to the macro.
Tap the button with the action(s) you want to add to the macro.
The ‘Macro’ screen appears.
The name of the selected button is added at the bottom of the Action List.
The macro will execute all the actions that are assigned to this button.
4
You can select other buttons to add to the macro.
To add a delay to the action list
You can add a delay to the action list e.g. to insert a short pause between turning
on a device and sending commands to it, allowing the device to warm up.
1
Tap
in the ‘Macro’ screen.
The ‘+’ button and ‘-’ button appear on the two middle firm keys below the
touch screen.
2
To increase the delay, tap (and hold) the firm key labeled ‘+’.
-or-
To decrease the delay, tap (and hold) the firm key labeled ‘-’.
Note
You can still change the delay later on.
To add a beep to the action list
To determine when the macro execution is finished, it is useful to add a beep as
final command in the action list.
1
Select the action in the action list, where you want to add a beep.
The action is selected.
2
Tap
in the ‘Macro’ screen.
A default beep is added to the action list, after the selected action.
To test the macro
You do not have to exit the Macro Tool to try out the macro you created or edited.
From within the Macro Tool you can test the macro. Pronto NG executes all actions
User Guide
35
as you defined them in the action list.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
In the ‘Macro’ screen, press the left firm key labeled
Pronto NG executes the actions in the action list.
.
Note
Make sure that you keep Pronto NG aimed at your Home Theater equipment
during the macro execution.
To finish the macro
Tap
in the ‘Macro’ screen.
The macro is created and assigned to the button you selected as a target.
-or-
Tap
in the ‘Macro’ screen.
The Tools Menu appears again without creating the macro.
Editing a Macro
Moving an action in the action list
1
To display the ‘Macro’ screen with the action list assigned to the
button, follow the instructions 1 to 5 as described in ‘Creating a Macro’
on page 34.
2
3
Tap the action in the action list you want to move in the ‘Macro’ screen.
The selected action is highlighted.
In the ‘Macro’ screen, tap the Move Up button
Move Down button below the action list.
or the
The selected action moves up/down in the action list.
4
You can select other actions to move.
Deleting an action from the action list
1
2
To display the ‘Macro’ screen with the action list assigned to the
button, follow the instructions 1 to 5 as described in ‘Creating a Macro’
on page 34.
Tap the action in the action list you want to delete in the ‘Macro’
screen.
The selected action is highlighted.
3
4
In the ‘Macro’ screen, press the right firm key labeled
The selected action is deleted from the action list.
.
You can select other actions to delete.
User Guide
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Creating and Editing Timers
With the Timer Tool you can define actions to be carried out at predefined times.
For instance, you can switch on the lights or program your VCR to record your
favorite daily TV-show.
Note
When a timer is executed, you will hear a beep and a Timer message appears on
screen.
If Pronto NG is performing another task (sending out IR codes, testing a macro, ...)
when a timer is due to be executed, Pronto NG first continues performing the
current task.
Creating and Editing Timers
Adding a Timer
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap
in the Tools Menu.
The ‘Timer Tool’ information screen appears.
Tap
.
The ‘Timer’ screen appears.
4
In the ‘Timer’ screen, tap
new timer to the list.
to add a
A new timer is added to the Timers list.
By default a new timer is labeled Timer and a
number. It has no start and stop actions defined.
5
6
7
To label the timer, tap
in ‘Labeling a Timer’ on page 38.
, as described
To define the start and stop actions for the timer, tap
described in ‘Editing a Timer’ on page 39.
, as
In the ‘Timer’ screen, tap
The ‘Timer’ screen closes and the Tools Menu appears again. The timer is
added.
.
-or-
In the ‘Timer’ screen, tap
.
The Timer screen closes without adding the timer.
User Guide
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Deleting a Timer
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap
in the Tools Menu.
The ‘Timer Tool’ information screen appears.
Tap
.
The ‘Timer’ screen appears.
4
5
6
7
Tap the label of the timer you want to delete.
The timer is highlighted.
In the ‘Timer’ screen, tap
.
A message screen appears.
In the message screen, tap
.
The timer is deleted from the list.
In the ‘Timer’ screen, tap
.
The ‘Timer’ screen closes and the Tools Menu appears again. The timer is
deleted.
-or-
In the ‘Timer’ screen, tap
.
The Timer screen closes without deleting the Timer.
Labeling a Timer
The default name for a timer is ‘Timer’ followed by a number, for example Timer 5.
1
2
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The ‘Timer Tool’ information screen appears.
User Guide
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
3
4
5
Tap
.
The ‘Timer’ screen appears.
Tap the label of the timer you want to label.
The timer is highlighted.
In the ‘Timer’ screen, tap
The ‘Labeling’ screen appears.
.
6
7
Label the timer as described in ‘Labeling Elements’ on page 23.
In the ‘Labeling’ screen, tap
.
The ‘Timer’ screen appears again and the timer is relabeled.
8
In the ‘Timer’ screen, tap
The Tools Menu appears again.
.
Editing a Timer
1
2
3
4
5
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The ‘Timer Tool’ information screen appears.
Tap
.
The ‘Timer’ screen appears.
Tap the label of the timer you want to edit.
The timer is highlighted.
In the ‘Timer’ screen, tap
The ‘Editing Timer’ screen appears.
.
6
To edit the timer, execute the following
steps:
1
2
3
Set the Start Date.
See ‘Setting the Start Date’ on page 40 for more information.
Set the Start Time.
See ‘Setting the Start Time or Stop Time’ on page 40 for more information.
Define the Start Action.
See ‘Defining the Start Action or Stop Action’ on page 41 for more details.
User Guide
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
4
5
6
Set the Stop Time.
See ‘Setting the Start Time or Stop Time’ below for more information.
Define the Stop Action.
See ‘Defining the Start Action or Stop Action’ on page 41 for more details.
Define the Repeat Settings.
See ‘Defining the Repeat Settings’ on page 42 for more information.
7
8
In the ‘Editing Timer’ screen, tap
The timer settings are defined. The ‘Timer’ screen appears again.
.
In the ‘Timer’ screen, tap
The Tools Menu appears again.
.
Setting the Start Date
When you add a new timer the Start Date is the current date by default. The Stop
Date is calculated automatically based on the Start Date, the Start Time and the
Stop Time.
To change the Start Date:
1
2
In the ‘Editing Timer’ screen, tap the Day button.
The Day button is selected. The labels ‘+’ and ‘-’ appear for the two middle
firm keys.
To increase the value, press (and hold) the firm key labeled ‘+’.
-or-
To decrease the value, press (and hold) the firm key labeled ‘-’.
3
4
Tap the Day button again.
The Day is set.
Repeat step 1 to 3 for the Month and the Year button.
The Start Date is set.
Setting the Start Time or Stop Time
1
2
In the ‘Editing Timer’ screen, tap the Start Time button or Stop Time
button.
The Start Time button or Stop Time button is selected. The labels ‘+’ and ‘-’
appear for the two middle firm keys.
To increase the time, press (and hold) the firm key labeled ‘+’.
-or-
To decrease the time, press (and hold) the firm key labeled ‘-’.
User Guide
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
3
Tap the Time button again.
The new Start Time or Stop Time is set.
Note
If the Stop Time lies before the Start Time, the Stop Date automatically jumps to
the next day.
Defining the Start Action or Stop Action
Pronto NG uses a similar procedure to define the Action List for the Start Action or
the Stop Action of the selected timer as in the Macro Tool. See ‘Creating and
Editing Macros’ on page 34 for more information.
Example Some examples of timer actions are: switching on your lights at a specific time
or recording your favorite daily TV-show with your VCR.
1
In the ‘Editing Timer’ screen, tap the
The ‘Macro’ screen appears.
or
button.
Note
You have to define a Start Action before you can define a Stop Action.
The Stop Action button is grayed out until a Start Action is set.
2
In the ‘Macro’ screen, tap
The last visited page appears again.
.
3
4
Navigate to the Device and the Page that contains the button you want
to add to the macro.
Tap the button you want to add to the action list of the timer.
The ‘Macro’ screen appears.
The name of the selected button is added at the bottom of the Action List.
The macro will execute all the actions that are assigned to this button.
5
In the ‘Macro’ screen, tap
The Start Action or Stop Action is defined. The ‘Editing Timer’ screen appears
again.
.
User Guide
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Defining the Repeat Settings
If you want the timer to repeat itself on more than one occasion, you can use the
repeat settings.
1 In the ‘Editing Timer’ screen, tap the
button.
The ‘Repeat Settings’ screen appears.
Repeat toggle
2
Tap the repeat toggle button
By default ‘No’ is selected.
.
The Repeat button toggles between the three settings:
■
■
■
No: This is the default setting;
Daily;
Weekly.
1
2
To change the setting to ‘Daily’, tap the button again.
Every day of the week is automatically selected.
If you want to set an end date for the repeating timer, select the
End Date check box.
The End Date is enabled.
3
Define the End Date, as described in ‘Setting the Start Date’ on
page 40.
The End Date is defined.
-or-
1
To change the setting to ‘Weekly’, tap the button again.
The current day is selected.
2
Select or deselect the different days of the week on which the
timer has to be executed.
User Guide
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
3
If you want to set an end date for the repeating timer, select the
End Date check box.
The End Date is enabled.
4
Define the End Date, as described in ‘Setting the Start Date’ on
page 40.
The End Date is defined.
-or-
To change the setting to ‘No’, tap the button again.
The timer will not be repeated.
3
In the ‘Repeat Settings’ screen, tap
.
The ‘Editing Timer’ screen appears again. Feedback about the repeat settings
is provided below the button.
Activating Timers
Note
You can only activate timers if the start time is in the future and a start action is
defined for the timer.
1
2
3
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap in the Tools Menu.
The ‘Timer Tool’ information screen appears.
Tap
in the ‘Timer Tool’ information
screen.
The ‘Timer’ screen appears.
4
Tap the check box in front of the timer that you want to activate.
The timer is activated.
User Guide
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
5
In the ‘Timer’ screen, tap
The ‘Timer’ screen closes and the Tools Menu appears again. The Timer icon
appears next to the time indication.
.
-or-
In the ‘Timer’ screen, tap
.
The Timer screen closes without activating the timer.
Note
In the Timers list, activated timers are displayed first, followed by the not-
activated timers. Both activated and not-activated timers are listed
chronologically.
Operating Pronto NG
with the Cursor
The cursor is set by default to operate the devices, e.g. to navigate through an
on-screen TV menu. The cursor contains 4 cursor keys: Right, Left, Up and Down.
Each cursor key contains an action list. This list depends on the device that is
being operated.
Up
Toggle button
OK
Home button
Left
Down
Right
The cursor can also be used to navigate through devices and pages on Pronto NG’s
touch screen.
When you enable the cursor navigation in the Settings Pages, the touch
screen navigation with the Left Device and Right Device buttons at the top area
of the touch screen disappears and the Cursor Navigation icon
appears in
the top left corner. You use the cursor for navigating, and not for operating your
devices, until you disable the cursor navigation again.
User Guide
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
To set the cursor navigation:
1
2
3
4
5
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Select the
.
The first Settings Page appears.
Press the Page Down hard button at the left side of the Pronto NG.
The second Settings Page appears.
Tap
in the second Settings Page.
The cursor navigation is enabled. The Toggle hard button is activated.
Tap the Pronto NG icon
in the top center of the touch screen to exit
the Settings Tool.
To use the cursor for navigating the Pronto NG:
6
7
8
Press the Left and Right buttons of the cursor.
Pronto NG navigates through the devices.
Press the Up and Down buttons of the cursor.
Pronto NG navigates through the pages.
Press the Toggle button to easily switch from navigating on
Pronto NG to control audio/video equipment.
The Device Left and Device Right buttons appear in the top area of the
touch screen and the cursor is used for controlling audio/video equipment.
9
Press the Toggle hard button again to switch back to cursor navigation.
User Guide
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Operating Pronto NG with RF
By default, Pronto NG uses infrared (IR) signals to operate devices. IR signals
have an operating distance of approximately 30 ft (10 m).
IR signals
However, you can choose to have Pronto NG working with radio frequency (RF)
signals to operate devices from a distance or from an adjacent room.
An RF Extender (not included) is therefore required.
The RFX6000 is an RF Extender that can be used in combination with
Pronto NG. The RF Extender receives RF signals from Pronto NG and converts them
into IR signals, sent out to the device. Therefore, the RF Extender has to be placed
near the device you are operating with the RF Extender’s sending eye pointed
towards the device.
RF signals
IR signals
Pronto NG
RF Extender
User Guide
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Selecting RF to Operate your Devices
1
2
3
4
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Tap
in the Tools Menu.
The ‘RF IR Tool’ screen appears.
Tap
.
The Device Overview appears.
Tap the Device for which you want to select RF.
The ‘Select IR or RF’ screen appears. By default IR is selected in the Sending
Signals list.
The Define RF button is disabled.
5
6
7
Choose RF in the Sending Signals list.
The Define RF button is enabled.
Tap
.
The ‘RF Settings’ screen appears.
Select the RF Channel in the RF Channel ID list you use for the RF
Extender.
The RF Channel on the RFX6000 has to be the same as the RF Channel on
Pronto NG.
8
Select the Extender ID in the Extender ID list you use for the RF
Extender.
The Extender ID on the RFX6000 has to be the same as the Extender ID on
Pronto NG.
Note
You can use several RF Extenders with your Pronto NG. For each RF Extender
you use for your devices, you need to set the RF Channel and the Extender ID.
The RF Channel is identical for all RF Extenders. The Extender ID on the
RFX6000 is unique for each RF Extender.
9
Tap
in the ‘RF Settings’ screen.
The RF settings are saved.
Pronto NG will send out RF signals for the selected device.
Note
Try to keep Pronto NG and the RF Extender away from metal objects, as this will
have a negative impact on the range.
User Guide
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Power Features
Selecting IR to Operate your Devices
1
Tap and hold the Pronto NG icon
touch screen for 3 seconds.
in the upper left corner of the
The Tools Menu appears.
2
3
4
5
6
Tap
in the Tools Menu.
The ‘RF IR Tool’ screen appears.
Tap
.
The Device Overview appears.
Tap the Device for which you want to select IR.
The ‘Select IR or RF’ screen appears. RF is selected in the Sending Signals list.
Choose IR in the Sending Signals list.
The ‘Define RF’ button is disabled.
Tap
in the ‘Select IR or RF’ screen.
Pronto NG will send out IR signals for the selected device.
User Guide
48
Download from Www.Somanuals.com. All Manuals Search And Download.
ProntoEdit NG
If you want to personalize your Pronto NG even more beyond its standard
programming features, ProntoEdit NG is the tool for you to use. ProntoEdit NG is
Pronto NG’s companion software that you find on the included CD-ROM. Please
check the website to make sure that you have the latest version. You can find
To learn how to work properly with ProntoEdit NG, consult its online help system
accessible via the Help menu or by pressing F1.
With ProntoEdit NG you can:
■
Upload and download new configurations to and from your Pronto NG.
You do this with the PC cable included with your Pronto NG:
1
2
Plug one end of the cable in the USB port on your computer.
Plug the other end of the cable in the USB port on Pronto NG.
USB port
■
■
Add, delete, modify and move control panels, devices and commands
anywhere on the touch screen;
Save, duplicate and share configuration files, codes or devices with other
Pronto NG users;
■
■
Import new graphics to create new buttons and designs;
Use .BMP -graphic files. You can now place buttons with a transparent
background on top of a background image and let transparent buttons overlap.
You use the color in the upper left corner of the bitmap as transparency color.
Personalize configuration files to optimize the use of your Pronto NG;
Copy, Paste and Edit plain IR codes that you can exchange with other
Pronto NG users;
■
■
■
■
Preview new configuration files on ProntoEdit NG Simulator, to check what
Pronto NG’s interface will look like.
Create and edit macros. In ProntoEdit NG you have access to the more
advanced features for macros.
User Guide
49
Download from Www.Somanuals.com. All Manuals Search And Download.
ProntoEdit NG
Some example screens of what you can accomplish with ProntoEdit NG:
User Guide
50
Download from Www.Somanuals.com. All Manuals Search And Download.
FAQ
Why don’t my buttons work properly?
When you find that your Pronto NG does not send out the commands in
accordance with what is indicated on the touch screen, it is advised to recalibrate
the touch screen. Calibration is necessary when you notice that tapping a button
activates one of the adjacent buttons or when you have to tap next to a button to
activate it. Calibration enables Pronto NG to place the icons on the touch screen in
line with their predefined functions.
Attention Never use an actual pen, pencil or other sharp object on the touch screen. Use a
pointy object like a plastic-tipped pen or a stylus intended for use with touch
screens.
How do I calibrate the touch screen?
1
2
3
4
Tap and hold the Pronto NG icon
touch screen for 3 seconds. The Tools Menu appears.
in the upper left corner of the
Select
.
The first Settings Page appears.
Press the Page Down button at the left side of the Pronto NG.
The second Settings Page appears.
Tap
in the second Settings Page.
The ‘Calibration’ screen appears.
5
6
7
8
Tap the upper left corner on the touch screen.
Tap the lower right corner on the touch screen.
Tap the upper right corner on the touch screen.
Tap the lower left corner on the touch screen.
The touch screen is calibrated.
-or-
Press the middle firm key, labeled
.
The second Settings Page appears again without calibrating the touch screen.
9
Tap the Pronto NG icon again to exit the Settings Tool.
User Guide
51
Download from Www.Somanuals.com. All Manuals Search And Download.
FAQ
How do I reset Pronto NG?
Normally, resetting Pronto NG is not necessary. However, if Pronto NG’s touch
screen freezes or if you notice unusual behavior, you need to perform a reset to get
Pronto NG running again.
1
2
Press the latch on the battery cover with your thumb and then slide the
cover forward firmly.
Lift off the battery cover.
You can find the Reset button in the battery compartment.
3
4
Use an unfolded paperclip or a sharp
pencil to carefully press the Reset
button.
Pronto NG restarts.
Pronto NG beeps twice to indicate
it is ready for use.
Reset button
Set the time again. See ‘Changing the Time’ on page 12 for more
information.
Note
If you reset Pronto NG, all personal changes like saved and programmed
commands, IR codes, timers and macros are retained.
Why does a device respond to some RF signals and not to others?
Not all commands for all devices work properly with RF signals.
If a device does not respond properly to RF signals sent out by Pronto NG, you
have to reconfigure Pronto NG to operate the device with IR signals.
User Guide
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
General Problems
Pronto NG shuts off automatically
This is a timeout feature of Pronto NG to save power. You can change the time
Pronto NG stays active in the Settings Tool.
See ‘Setting the Timeout of the LCD Screen’ on page 31 for more information.
The touch screen buttons on the Pronto NG do not respond
properly
If the touch screen buttons on the Pronto NG do not respond properly, calibrate the
touch screen.
See ‘Calibrating the Touch Screen’ on page 33 for more information.
Devices do not respond to commands from Pronto NG
■
■
■
Make sure the Pronto NG’s sending eye is pointed towards the device you are
operating.
Check if the Low Battery icon has appeared on screen. If so, replace the
batteries.
Check if your device understands Philips-Marantz RC codes. Normally you can
find this in the documentation of your device.
■
■
■
Make sure you have defined the correct brands for your devices. (p. 18)
Make sure you have defined the correct code set for your devices. (p. 19)
Check if the button you are trying to use is assigned properly via Brand Tool or
via Learn Tool. (p. 21)
■
■
Check if your device is in RF mode. Switch your device back to IR mode. (p. 48)
If you have set up your Pronto NG to operate devices with RF signals:
■
■
■
■
■
Check in the RF IR Tool if the devices you want to operate are set up
properly. (p. 47)
Check if the Extender ID and the Channel on your Pronto NG match the ID
and the Channel on the RF Extender.
Make sure the RF Extender is placed near the devices you want to use
with RF signals.
Make sure that the RF Extender’s sending eye is pointed towards the
device.
Change the Channel if you notice interferences from other RF channels.
■
If you want to use RF signals for devices on different locations, you need more
than one RF Extender. See the User Guide of the RF Extender for more
information.
User Guide
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Customizing Problems
Buttons are not sending the correct commands
■
■
■
■
■
Make sure you have defined the correct brands for your devices. (p. 18)
Make sure you have defined the correct code set for your devices. (p. 19)
Make sure you calibrate your screen correctly. (p. 33)
Check whether the button of the device is learned properly. (p. 21)
Check whether the macro recorded properly. (p. 34)
Macros do not work
■
Make sure Pronto NG’s sending eye is pointed towards the device the entire
time the macro is being executed.
■
■
■
■
The sending eye is located at the top of Pronto NG.
Insert delays to allow devices to start up properly.
Check for inactive buttons in your macro.
Check if you did not reprogram the buttons. Macros do not store commands,
they store buttons. If you reprogram a button, the macro executes the new
command assigned to the button.
Pronto NG will not learn commands
■
Make sure your Pronto NG and the remote control are positioned correctly.
■
When the sending eye of your existing remote control is not pointed
towards the learning eye of the Pronto NG, Pronto NG might not receive
the signals properly. Align the remote controls as correctly as possible.
When the distance between your existing remote control and the Pronto
NG is too short or too long, Pronto NG might not receive the signals
properly. Try out several distances between 4 and 8 inches (10 and
20 centimeters) to learn the commands.
■
■
Avoid programming Pronto NG under bright fluorescent light or in sunlight:
it might affect the infrared signals.
■
■
Make sure the batteries in the Pronto NG are not low.
Press and hold the key on the other remote control for more than one second.
The configuration file is corrupted
When the configuration file is corrupted, you can use ProntoEdit NG to download a
new configuration file. Taken into account that all your customized commands,
devices and macros will be lost and you will have to reprogram your Pronto NG.
Therefore it is recommended to save the configuration by uploading it to the PC
with ProntoEdit NG.
User Guide
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Timers do not work
■
■
■
Check if the timer has been activated. (Activating Timer, p. 43)
Make sure a Start Action for the timer has been defined properly. (p. 41)
Check whether the date and time of your Pronto NG are set properly. (p. 12)
Memory Storage Problems
Memory storage problems can be the cause of Pronto NG not saving a macro.
Storage problems can be caused by a full memory or by low batteries.
■
■
Consult the third Settings Page to see how much memory is available. (p. 30)
Consult the first Settings Page or the battery icon at the top of your screen to
check the battery status. Replace the batteries if necessary. (p. 10)
Pronto NG error messages
If one of the following error messages occurs, please contact your dealer or the
Philips customer service:
■
■
Invalid CF version or corrupt flash;
Incorrect software version.
When your Pronto NG does not respond and the screen stays blank:
1
2
Download the configuration file again.
When downloading the configuration file again does not work,
Connection to the PC
■
Make sure the batteries in the Pronto are not low while using ProntoEdit NG to
download or upload.
■
Do not pull out the USB cable while uploading or downloading a configuration
file.
User Guide
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining Pronto NG
Important Notices
Take care not to scratch the touch screen
Use your finger to tap the touch screen or use plastic-tipped pens intended for use
with touch screen.
Never use an actual pen, pencil or other sharp object on the touch screen.
Protect Pronto NG from temperature extremes
Keep Pronto NG away from heaters and other heat sources.
Pronto NG is not waterproof
Pronto NG should not be exposed to rain or moisture.
Do not store or use Pronto NG in any location that is extremely damp or wet.
When you have spilled water on Pronto NG, you have to take out the batteries and
let Pronto NG dry for 48 hours before you insert the batteries again.
The touch screen of Pronto NG contains a glass element
Do not drop Pronto NG or subject it to any strong impact.
Cleaning Pronto NG
■
Use a soft, damp cloth to clean Pronto NG.
■
If the touch screen of Pronto NG is spoiled, clean it with a soft cloth
moistened with a diluted window-cleaning solution.
Do not use a corrosive detergent or an abrasive sponge.
Avoid the use of abundant water.
■
■
Upgrading Pronto NG
You can find the latest upgrades of your Pronto NG software (when available) on
already registered you can enter your username and password to log in. Otherwise
you can register and become a ProntoZone member for free.
User Guide
56
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Symbols
Pause
Stop
Normal run; normal speed
Normal run; normal speed
Fast run; fast speed
Fast run; fast speed
Slow run; slow speed
Slow run; slow speed
Eject
Recording, general
Key
Navigate
Still mode
Tape running direction
Next track
Previous track
Fast forward to index
Rewind to index
Frame by frame, general
Frame by frame, general
Subtitle
Cancel picture
Picture-in-picture mode
Menu
Picture-in-picture shift
Picture-in-picture swap
Multi-picture display
Picture-in-picture select
Teletext mode
User Guide
57
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Symbols
Page number up
Page number down
Page enlargement
TV and text mixed
1st or 2nd language
Last view; previous program
Stand-by
Zone focus: long distance
Zone focus: very short distance
Single or multi-digit selection
Brightness; brilliance
Contrast
Brightness/contrast
Color saturation
Lamp; lighting; illumination
Split screen freeze / double screen freeze
Split screen swap / double screen swap
Split screen / double screen
Movie expand
Personal preference
Picture-in-picture freeze
Main index page
Picture freeze
Programmable timer; general
Enter
Application assistance
Actual time on screen
EPG / Electronic Program Guide
Video output
User Guide
58
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Symbols
Read data from store
Write data into store
Page hold
Sound muting
Additional information on screen
Spatial sound effect
Television; video
Sound; audio
Surround sound
Dolby Digital
Digital Theater Systems
Active control
User Guide
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
The specifications and design of this product are subject to change without notice.
Display
Monochrome 3.8” touch screen LCD with 16 gray scales and
digital contrast control
320x240 pixels resolution
Blue LED-backlight for LCD and buttons
Interface
Software
USB 1.1-port connector
Database with IR codes to operate more than 800 brands
Built-in Philips IR codes
Total number of devices only limited by memory
Infrared (IR)
4 high performance IR-sending LEDs, 1 receiver LED
Operating distance of approximately 33 ft (10 m)
Learning frequency up to 78 KHz and 455 KHz
Radio frequency
(RF)
Band: 418 MHz
16 Extender ID’s and 4 Channels
Memory
Power
4 Mbytes
Power on by tapping the touch screen or by pressing a button
Power off automatically
Dimensions
(HxWxD)
6.07 inch x 3.64 inch x 1.10 inch
(154,2 mm x 92,4 mm x 27,8 mm )
Operating
41°-113° F
temperature
(5° – 45° C)
Accessories
Included:
USB cable for PC connection
CD-ROM with ProntoEdit NG software
4 AAA batteries
Not included:
Docking station
AAA rechargeable battery pack (4x1.2 V)
RF Extender (RFX6000)
ProntoEdit NG
PC requirements:
Windows 98SE, ME, 2000, XP
64 MB of RAM
75 MB of free hard disk space
Free USB Port
CD-ROM player
IR-database information:
Redesigned by UEI Technology
Licensed under U.S. Patent 5,689,353
Portions © UEI 1999
User Guide
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Action
An action is a command that will be executed by Pronto NG. An action
can be an IR code, a link, a delay or a beep. You can assign one or more
actions to a button or a hard button. It is the same as a macro.
Action list
An action list is a list of actions assigned to a button or a hard button.
An action list can contain up to 250 actions.
Animation mode Pronto NG provides navigation feedback through graphical animations.
These animations can be found in the Animation mode. You can enable
and disable the animations of your Pronto NG in the Settings Pages.
Branding
Pronto NG contains a list of brands and their according IR codes in its
database. Pronto NG uses IR codes to control devices. Because there are
several brands using specific IR codes, you have to define the brand and
code set for each device.
Button alias
See Link.
Button backlight The Button backlight is a special light source that is placed behind the
hard buttons on your Pronto NG, enhancing the visibility of these
buttons.
Calibration
Calibrating the touch screen enables Pronto NG to exactly match the
icons on the touch screen with their predefined functions.
Code set
A code set is a list of IR codes. Audio and video devices of different
brands use different code sets. A device can only receive and execute
functions from the correct code set.
Cursor navigation There are two ways of navigating through Pronto NG: using the touch
screen or using the cursor for navigation. When you select cursor
navigation, the cursor can only be used for navigating through devices
and pages on Pronto NG touch screen, not for controlling audio/video
equipment.
Delay
A delay is a pause between two actions. A delay gives the device
enough time to execute the first action before it receives an impulse to
execute a second action.
Device
Every device in the configuration file appears on the Device Overview
Page of Pronto NG and in the tree view in ProntoEdit NG. A device
represents the equipment you want to control with Pronto NG, for
instance a TV, VCR, CD player, Amplifier, Satellite receiver or any device
operated by an IR remote. The device contains a number of pages with
buttons.
Device action
A device action is an action that is executed automatically when you
select a device. E.g. when you select TV, you can learn your Pronto NG
to switch on the TV at the same time.
Device Overview You use the Device Overview on Pronto NG to access the different
devices. The Device Overview contains buttons for each device in the
configuration. By pressing these buttons you navigate to the first page
of the selected device.
User Guide
61
Device settings The device settings are the type of device, the brand, the IR code set
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
and the functions. In order to control a device with your Pronto NG, you
first have to set the device settings.
Device template You can create a template from a device in ProntoEdit NG Advanced
Mode. When you add a new device on Pronto NG, this template will be
used.
Firm key
Pronto NG has 4 firm keys located below the touch screen. The label of
a firm key is displayed at the bottom of the touch screen. You can
configure the functions of the firm keys, just like most hard buttons and
the buttons on the touch screen. The strength of the firm keys is that
you can also configure their label, so they can always indicate the
function assigned to them.
Hard button
A hard button is a button that can be pressed and generates an event.
Hard buttons can be found on Pronto NG. Their layout and visual aspects
cannot be changed. You can configure the functions of the hard buttons,
just like the firm keys and the buttons on the touch screen.
IR
Short for infrared.
IR code
Pronto NG sends out infrared (IR) signals to operate devices. IR codes
for all kinds of video and audio device brands are stored in Pronto NG’s
universal database. By selecting IR codes and assigning them to buttons
and hard buttons, you can program your Pronto NG to operate your
equipment. When IR codes are not present in the database, you can
always learn them from the conventional remote control of your
equipment.
Label
A label is the text you want to put on a soft button or a firm key.
Short for liquid crystal display.
LCD
LCD backlight
LCD backlight is a special light source that is placed behind the LCD
screen, enhancing the visibility of the screen.
Light sensor
Link
The light sensor on your Pronto NG causes the backlight to switch on
automatically according to the ambient light of your home theater
environment.
A link, also called a button alias, is a shortcut from the action list of one
button to the action list of another button. Instead of adding the same
actions to several buttons or hard buttons, you can create a link and
reuse the action list. When your Pronto NG is executing an action list
and comes across a link, the action list referred to by that link is
executed.
Macro
A macro is a sequence of actions executed when pressing a single
button on Pronto NG. Every button or hard button can act as a macro and
perform a list of commands. It is the same as an action list.
Mode animation When you switch from using the Pronto NG to the Tools Menu, the
Pronto NG icon shifts at the top area of the touch screen. This is called
a ‘mode animation’.
User Guide
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Page
A page of a device is the area of 320 by 240 pixels on Pronto NG’s touch
screen containing buttons or other objects.
Page animation When you switch from one page to another, the first page slides out of
the screen and the second page slides in the screen. This is called a
‘page animation’.
Pronto NG
Pronto NG is a universal remote control with a touch screen. You can
customize and fully configure Pronto NG to your personal needs: the
devices you want to operate, the functions you want to perform and the
layout on Pronto NG.
ProntoEdit NG
ProntoEdit is the visual editor for creating and configuring Pronto
Configuration Files.
RF
Short for Radio Frequency.
RF code
You can choose to operate your devices with RF signals instead of IR
signals. To use RF signals, you need an RF Extender. The advantage of
RF is that it spreads in all directions and that it pervades walls. In other
words, you can operate your devices from an adjacent room.
RF Extender
An RF Extender is a converter box that receives RF signals and turns
them into IR signals to operate devices. When your Pronto NG sends out
RF codes, the RF Extender receives them and sends out IR codes to your
devices.
RFX6000
The RFX6000 is an RF Extender that can be used in combination with
Pronto NG.
Settings Tool
The Settings Tool allow you to consult and adjust several settings, for
instance consulting the battery level, setting the date and time,
calibrating the touch screen, ...
Simulator
Pronto NG simulator is a separate application in ProntoEdit NG package,
which simulates every aspect of your Pronto NG. You use Pronto NG
simulator to test your PCF without the need to download it to your
Pronto NG. When you make changes in Pronto NG simulator, they will
not be saved in the configuration file.
Soft button
Timer
A soft button is a button that can be found on the touch screen. The
layout and the visual aspects of a soft button can be changed. You can
also configure the functions of the soft buttons.
A timer allows you to define actions to be carried out at predefined
times. For instance, you can set an alarm or program your VCR to record
your favorite daily TV-show.
Touch screen
USB
The touch screen of your Pronto NG is the centered area that contains
soft buttons you can use to operate the remote control.
USB (Universal Serial Bus) is a ‘plug and play’ interface between a
computer and add-on devices (such as audio players, joysticks,
keyboards, telephones, scanners, and printers).
User Guide
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
C
action, 35
calibrating the touch screen, 33
action list
changing
action, 34
date, 13
beep, 34
language, 14
delay, 34
time, 12
time format, 12
channel
channel down, 5
channel up, 5
activating timer, 43
Add Tool, 26
adding
action, 35
clock settings. See time
beep, 35
delay, 35
code set
new device, 26
timer, 37
searching, 20
selecting, 19
adjusting
connection to docking station, 6
contrast, 11
copying existing device, 27
creating macro, 34
cursor, 5, 44
LCD backlight timeout, 30
LCD screen timeout, 31
light level, 31
volume level, 32
animation mode, 9, 33
full, 33
cursor navigation, 9, 32
D
mode, 33
none, 33
date, 13
delay, 35
page, 33
Delete Tool, 28
deleting
action in a macro, 36
button action, 28
device, 28
timer, 38
device
B
batteries, 10
battery compartment, 6
battery cover, 10
beep, 34
brand
installing, 19
searching, 20
selecting, 18, 20
Brand Tool, 19
button, 5
adding, 26
copying, 27
deleting, 28
labeling, 25
moving, 29
backlight, 6
contrast, 11
cursor, 5, 44
hard buttons, 5
labeling, 24
learning, 22
Page down, 6
Page up, 6
device action learning, 22
Device Overview, 15
download, 49
E
editing
macro, 36
timer, 39
error message, 55
reset, 6
Toggle, 46
button action deleting, 28
H
Home Theater Control Panel, 4
User Guide
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
I
N
infrared, 46
navigation
cursor, 9, 32, 44
touch screen, 32, 44
installing brand, 19
IR signals, 46, 47, 48
O
K
operating the Pronto NG
cursor navigation, 44
RF signals, 46
keyboard, 23
symbols, 23, 56
zoom, 23
touch screen navigation, 44
troubleshooting, 53
Overview
Device, 15
Page, 16
L
Label Tool, 23
labeling
button, 24
device, 25
page, 25
P
page animation, 33
page labeling, 25
Page Overview, 9, 16
Pronto NG, 4
adjusting the settings, 30
appliance, 5
customizing, 17
Device Overview, 15
IR signals, 48
maintaining, 56
operating, 15
symbols, 23, 56
timer, 38
language, 14
LCD backlight timeout, 30
LCD screen, 5
LCD screen timeout, 31
Learn Tool, 21
learning
button, 22
device action, 22
remote control, 21
light level, 31
light sensor, 7
Page Overview, 16
resetting, 51
RF signals, 47
specifications, 60
touch screen, 7
turning on, 11
upgrading, 56
USB cable, 49
M
macro, 9
action, 35
beep, 35
creating, 34
delay, 35
USB port, 49
ProntoEdit NG, 49
ProntoEdit Simulator, 49
deleting action, 36
editing, 36
move, 36
R
testing, 35
radio frequency, 46
Remote Control, 4
repeat settings, 42
resetting the Pronto NG, 51
RF Extender, 46
RF IR Tool, 46
troubleshooting, 54
Macro Tool, 34
memory, 9
mode animation, 33
move action in a macro, 36
Move Tool, 29
Moving a Device, 29
multi language support, 9
RF signals, 46, 52
User Guide
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
labeling, 38
repeat settings, 42
start action, 41
start date, 40
start time, 40
stop action, 41
stop time, 40
Timer Tool, 37
Toggle button, 44
Tool, 17
S
screen, 5, 7
backlight, 31
calibrating, 33
light level, 31
light sensor, 7
timeout, 31
searching
brand, 20
code set, 20
Add, 26
selecting
Brand, 18
brand, 18, 20
Delete, 28
code set, 19
Label, 23
Learn, 21
Macro, 34
Moving, 29
RF IR, 46
Timer, 37
touch screen, 5, 7
touch screen calibration, 33, 51
transparency, 9
turning on Pronto NG, 11
settings, 30
animation mode, 33
calibrating the touch screen, 33
date, 12, 13
language, 14
LCD backlight timeout, 30
LCD screen timeout, 31
switch level, 30
time, 12
time format, 12
volume level, 32
Simulator, 49
specifications, 60
start action, 41
start date, 40
start time, 40
stop action, 41
stop time, 40
U
upgrading, 56
upload, 49
USB, 9
USB cable, 49
USB port, 6, 49
V
storage problems, 55
symbols, 23, 24, 57
volume
mute, 5
volume down, 5
volume level, 32
volume up, 5
volume level
hard buttons, 32
touch screen buttons, 32
T
testing the macro, 35
time, 12
time format, 12
timer, 9
activating, 43
adding, 37
deleting, 37
editing, 39
Documentation concept and elaboration:
The Human Interface Group, De Regenboog 11, 2800 Mechelen,
User Guide
66
3104 205 3275.4
Download from Www.Somanuals.com. All Manuals Search And Download.
|