In-Ceiling Speaker
CM600i
Technical Information for System Engineers
Key Features
• BroadBeam® waveguide technology
delivers a consistent BroadBeam® dis-
persion pattern for maximum coverage
area per speaker (up to 10 kHz, EASE™
documented).
• One 165 mm (6.5 in) polypropylene
woofer and one 25 mm (1.0 in) convex
aluminum tweeter with FerroFluid™
cooling mounted to a proprietary cast-alu-
minum M6™ motor-board and heat sink.
Tile bridge included
Specifications: CM600i
System Type
6.5” Coax outdoor (voice coil / 8 Ohm direct, 33 Watt
transformer for 25/70.7/100 Volt applications)
Frequency Response (- 3 dB)1
Low Frequency (-10 dB)1
Max. Program Power
Max. Continuous Power RMS2
Max. UL Program Power 3
Max. SPL dB @ 1 M
Sensitivity dB @ 1W/1M4
Impedance (nominal)
Tap Selector / Inputs
70 Hz - 22 kHz
60 Hz - 22 kHz
180 Watts
90 Watts
60 Watts
111 dB
• Rapid-installation blind-mount, fixed-
wing mounting mechanism with con-
stant-tension design affixing to ceiling
thickness tolerances ranging from 6.4
mm (0.25 in) to 42.9 mm (1.69 in).
91.5 dB (average over published frequency response range, 2.83 V)
• Separate tool-free magnetic grille &
bezel assembly for ease of install &
in-field painting.
8 Ohm (nominal)
6-Position rotary switch with voice coil direct (8 Ohm)
Coverage Angle (-6 dB@ 2 kHz)
Coverage Angle (-6 dB@ 10 kHz)
Directivity Factor (Q)
90º
130º
• Iridite-plated steel grille with protective
powder-coated finish for lasting durability.
6.4 (Averaged 100 Hz – 10 kHz); 9.1 @ 2 kHz
7.64 dB (Averaged 100 Hz – 10 kHz); 9.59 dB @ 2 kHz
Directivity Index (DI)
• Easy access 6-position selectable tap
switch for 25, 70.7 and 100 Volt applica-
tions with voice coil/8 Ohm direct sim-
plifies ordering & inventory tracking.
Transformer Taps
70.7 V
33 W
17 W
9 W
Output
106.5 dB
104 dB
101 dB
99.5 dB
96.5
100 V
33 W
17 W
9 W
Output
25 V
5 W
2.5 W
1.3 W
0.5 W
Output
106.5 dB
104 dB
101 dB
99.5 dB
98.5 dB
95.5 dB
92.5 dB
88.5 dB
• 91.5 dB average sensitivity offers high-
output capabilities & reduced amplifica-
tion costs.
6 W
6 W
3W
• Approval pending for UL 1480 rev. 5
& 2043, CE (EMC Directive 89/366/
EEC, EN55020, EN55013 & IEC529,
and Milspec 810.
Transducers
Low-Frequency Driver
High-Frequency Driver
Low-Frequency Voice Coil
1x165mm(6.5in)Polypropylenecone,butylrubbersurround
1x25mm(1.0in)Convexaluminumtweeterwithwaveguide
25mm(1.0in)
• Included accessories: Tile bridge, Euro-
block connector, paint mask, conduit plate.
Network Type
Low Pass
High Pass
Crossover Frequency
Enclosure Material
Grille
12 dB per octave, 2nd order
12 db per octave, 2nd order
3.0 kHz
Drawn aluminum backcan with ABS baffle
Iridite-plated steel with powder-coat finish
4 Pin, 5 mm Euroblock for individual or daisy chain connection
White or black
296.7 mm / 11.68 in
201.7 mm / 7.94 in
375.0 mm / 14.76 in
27.5 mm / 1.08 in
• Optional accessories: Pre-construction
bracket, junction box.
• High-quality black or white paint finish.
Custom paint colors optional.
Inputs
Color Options
Backcan Diameter
Backcan Deight
Visible Diameter
Visible Height
Weight
Description
The CM600i is a 6.5” 2-way blind-mount
in-ceiling speaker design that delivers
extended low-end response (60 Hz) and
optimal off-axis performance (up to 10
kHz, EASE™ documented). SoundTube’s
proprietary BroadBeam® waveguide
tweeter system delivers consistent high-
performance audio across the operating
bandwidth. The CM600i speaker design
incorporates a low-profile grille, propri-
etary M6™ motor-board and 6-position
tap switch with voice coil/8 Ohm direct.
Mounting hardware is included and fea-
tures a fast and secure constant tension
fixed-wing mounting system.
4.6 kG / 10.1 lbs
7.5 kG / 16.5 lbs
Shipping Weight
Accessories
Included
Optional
Tile bridge, Euroblock connector, conduit plate
Pre-Construction Bracket (AC-CM8-PCB),
Junction Box (AC-CM-BOX)
Packaging
2 per box
1
2
3
4
Frequency response is measured in half space and includes a low-frequency peak > + 3 dB.
Continuous power rating, EIA-426-B test.
UL testing specifies band-limited pink noise over the indicated frequency spectrum.
2.83 Volts at a distance of 1 meter.
SoundTube continually develops new product innovations and improvements. Updates to existing
products without prior notice are an example of SoundTube’s drive for constant improvement.
© 2006 SoundTube Entertainment, Inc. All rights reserved. PN TS-CM600 REV 03.03.06
Download from Www.Somanuals.com. All Manuals Search And Download.
In-Ceiling Speaker
CM600i
Technical Information for System Engineers
ance of 8 Ohms and be available for
25, 70.7 & 100 Volt modes with voice
coil/8 Ohm direct. The frequency-
dividing network shall have a cross-
over frequency of 3 kHz with slopes of
12 dB per octave (2nd order) for both
low & high pass filters. Rated power
capacity shall be at least 90 Watts con-
tinuous power (RMS) and conform to
EIA-426-B testing. Maximum continu-
ous output at 1 meter shall be 111 dB.
Sequence (MLS) and Time Delay
Patented SoundTube
Technologies
Spectrometry (TDS). Performance,
development and data acquisition
tools include: Gold Line TEF 20, CLIO,
LMS, LEAP, and proprietary modeling
software. EASE™ data are acquired
through an automated TEF 20/Out-
line/EASE™ interface.
SoundTube Entertainment is con-
stantly developing new technologies that
enhance audio product performance.
SoundTube Entertainment innovations are
protected by multiple U.S. & international
patents, which explicitly cover SoundTube
dome, enclosure and dispersion technolo-
gies. SoundTube Entertainment actively
defends its patents in order to protect
SoundTube resellers and end users.
EASE™ Data – 3-D polar plots.
SoundTubeSPEC™ – Proprietary
SoundTube speaker placement software.
Installation for the CM600i shall be
by 2-screw blind-mount, constant-ten-
sion winged assembly and shall attach
to ceiling thickness tolerances ranging
from 6.4 mm (0.25 in) to 42.9 mm (1.69
in). The fixed-wing assembly shall be
constructed of glass filled ABS material.
The external wiring input connector
shall be a 4-pin, 5 mm Euroblock for 8
Ohm or distributed systems and shall
accept from 10 – 22 gauge wire.
Architectural Specifications
Technical Data and
Specification Tools
The loudspeaker shall consist of a 165
mm (6.5 in) low-frequency transducer
and a 25 mm (1.0 in) high-frequency
transducer with a crossover network
installed in the ported enclosure. The
low-frequency voice coil diameter shall
be 25 mm (1.0 in).
Technical Data
SoundTube Entertainment strives to
provide complete and effective techni-
cal information and data to dealers,
engineers and designers. All data are
available from SoundTube Entertain-
Performance specifications of a
typical production unit shall be as fol-
lows: Useable frequency response shall
extend from 60 Hz – 22 kHz (-10 dB,
half space, no external equalization).
Measured sensitivity (2.83 Volt input,
1 meter) shall be at least 91.5 dB. The
speaker shall have a nominal imped-
The maximum backcan dimensions
shall be no more than 201.7 mm (7.94
in) in height by 296.7 mm (11.68 in) in
diameter. The maximum visible dimen-
sions shall be no more than 27.5 mm (1.08
in) in height by 375 mm (14.76 in) in diam-
Data Acquisition
All performance data acquired at
SoundTube’s Technical Measurement
Center (TMC) are analyzed using a
variety of standard measurement tech-
niques, including Measured Length
Polar Plots
250 Hz
500 Hz
1,000 Hz
125 Hz
4,000 Hz
8,000 Hz
10,000 Hz
2,000 Hz
™
™
Technical data, EASE plots, SoundTubeSPEC software & product downloads available at www.soundtube.com
Download from Www.Somanuals.com. All Manuals Search And Download.
In-Ceiling Speaker
CM600i
Technical Information for System Engineers
Mechanical Drawings
eter. The backcan shall be constructed of alu-
minum.
Side
Top
The system shall include a 16-gauge
galvanized steel support backing plate (tile
bridge) to reinforce the ceiling material and
tile support rails. The maximum tile bridge
dimensions shall be no more than 600.1 mm
(23.62 in) in length by 428.2 mm (16.86 in)
in width and 10.4 mm (0.41 in) in thickness
with 325.1 mm (12.80 in) cutout for speaker
mounting.
296.7 mm
(11.68 in)
201.7 mm
(7.94 in)
The grille shall be constructed of iridite-
plated, powder-coated steel with an ABS
bezel for lasting performance. The affixed
grille and bezel shall be mounted to the
speaker enclosure (backcan) via neodymium
magnets and include safety wire. Also
included are a paint mask for in-field paint-
ing and an installation aid that serves as a
handhold during mounting.
375 mm (14.76 in)
27.5 mm (1.08 in)
Included Accessories
The CM600i has an optional Pre-Con-
struction Bracket (AC-CM8-PCB) that shall
be compatible with an optional Junction
Box (AC-CM-JBOX). An 18-gauge hard-
wire lead, conduit connector and Eurob-
lock connector shall be included with the
Junction Box. The maximum dimensions
of the Pre-Construction Bracket shall be
no more than 635 mm (25.0 in) in length by
457.2 mm (18.0 in) in width and 127 mm (5.0
in) in thickness with a 326.1 mm (12.85 in)
cutout for speaker mounting.
325.1 mm
(12.80 in)
600.1 mm
(23.62 in)
Max.
42.9 mm (1.69 in)
Min.
6.4 mm (0.25 in)
Fixed Wing Mounting System
428.2
The system shall be the SoundTube CM600i
for both low and high impedance applications.
(16.86 in)
Tile Bridge
SoundTube Entertainment
6430 North Business Park Loop
Park City, Utah 84098
Phone 435.647.9555
Paint Mask
Fax
435.647.9666
Toll Free 800.647.TUBE
Optional Accesories
All SoundTube products come
with a 5-year limited warranty.
Pre-Construction Bracket (AC-CM8-PCB)
Junction Box (AC-CM-JBOX)
SoundTube Entertainment manufactures a complete line of speakers for:
Open-Ceiling • In-Ceiling • Surface-Mount • Outdoor • Sound-Focusing
All SoundTube products are designed and engineered in the USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|