TEATRO
V-3.0 AND PC-3.0
FLAT PANEL
L-C-R SOUND BAR SPEAKER
Download from Www.Somanuals.com. All Manuals Search And Download.
FLAT PANEL WALL MOUNT
ATTACHMENT INSERTS
8 3/16”
USE THESE SETS OF HOLES
FOR SPEAKER BRACKETS FOR
NORMAL WALL MOUNTING
CENTER INPUT
LEFT INPUT
RIGHT INPUT
FIGURE 1
least 2 holes on each bracket that line up over a wall stud. Drill the wall and install your anchors and fasten the brackets to the wall with the “J”
bend at the bottom (fig. 2 & 3).
Step 3
Place your TEATRO sound bar speaker face down on a soft clean surface with the grille on. Orient the speaker so the input terminal is on the
left hand side. The second pair of steel brackets supplied with the speaker is designed to attach to the threaded inserts on the rear of the
speaker cabinet with the 8 supplied #10-32x3/8” Philips screws. Simply align the holes on the brackets with the center and bottom set of
mounting holes on the rear of the speaker. Position the brackets similar to the ones mounted on the wall with the “J” bend up so it can hook
into the wall bracket. Attach brackets to the rear of the speaker using 4 screws per bracket (fig. 1 & 2).
Install one each of the 6, #10-32x1” Phillips screws in the threaded nut located in the bottom center of the “J” bend of the two wall mounted
brackets. These screws are for leveling the speaker. Just start the screws but do not screw in at this time.
Install the other 4, 1” screws in the end mounted nuts of the cabinet mounted brackets. These are the bracket locking screws and should be
install so they can be adjusted from the bottom of the speaker (fig. 3).
Assemble the 2 rubber stand-off bumpers next. Thread one nut onto each bumper stand-off and then one nylon washer. Run the nut about
half way down the screw. Thread each of the bumper stand-offs into the 2 lower inserts located on the bottom rear edge of the cabinet.
Step 4
There is 3 pair of gold binding post terminals
FIGURE 2
on the rear of the speaker cabinet. The
SPEAKER MOUNTING BRACKETS HOOK
terminals are marked for Right Input, Center
INTO WALL MOUNTING BRACKETS
Input and Left Input and should be
connected to the respective speaker channel
outputs on your receiver. Connect the
speaker wires to the correct terminals
observing the polarity indicated on the
terminal. Red is + or positive and black is – or
negative. Strip about ½” of insulation from the
Figure 1
wires and separate the wires as necessary. If
you are using other wire lugs or connectors,
attach them at this time to the bare wire.
Unscrew the binding post terminals and slip
the stripped end of the wire through the hole
in the metal post. Secure the wire in the post
by tightening the binding post terminal nut
down on the bare wire or lug. Make sure the
nut is tight and the wire will not pull out of the
terminal by lightly pulling back on the wire.
Tuck the speaker wire in behind the speaker
cabinet and if necessary or neaten up the
wire with the use of tie wraps.
SPEAKER MOUNT
BRACKETS
WALL MOUNT
BRACKETS
Step 5
The TEATRO sound bar speaker is now
ready to be mounted to the brackets that
were screwed to the wall in step 2. The
brackets are made to interlock with each
other. Raise the speaker so the brackets on
the rear of the cabinet are aligned with the
wall brackets and engage the “J” bends in the
STAND OFF BUMPER,
LOCK NUT, WASHER
two sets of brackets together. If the speaker is being installed very close to the bottom of the flat panel display the speaker brackets can be
slid into each other from the side. After the brackets are interlocked, it is a simple matter to center the speaker by sliding it side to side. The
speaker can also be leveled by turning in the appropriate height adjusting screw to raise and lower the ends of the speaker. This is done with
a #2 Phillips screwdriver from the bottom side of the bracket. Once the speaker position is trimmed up it should be locked in place using the 4
locking screws in the speaker bracket (fig. 3). Be carful not to over tighten the screws.
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the rubber stand-off bumpers by turning them either in or out to adjust the tilt of the speaker until the front is vertical. Lock the adjusting
screws in place by tightening the locking nuts against the rear of the cabinet. Please be certain that the nylon washer is between the nut and
the cabinet to protect the cabinet finish.
Step 6
FIGURE 3
Since the TEATRO sound bar speakers form
the front 3 speakers in a home theater
system for flat panel displays they are to be
used and set up as you would any normal 5.1
to 7.2 surround sound system for balance
and level adjustments. The amplifier should
be set to the small speaker mode for the
left/center/right front speakers for the best
performance. The subwoofer setting should
be set to 80 Hz. We recommend the use of
our Phase Technology subwoofers and
surround speakers for complimenting your
installation.
WALL MOUNTING BRACKET
LEVELING ADJUSTMENT
SCREW IN WALL BRACKET
SPEAKER MOUNTING BRACKET
LOCKING SCREWS IN
SPEAKER BRACKET
Step 7
The EVT™ switch which is located on the
front of the speaker under the grille activates
Phase Technology’s Enhanced Voice
Technology feature. This feature is designed to improve the clarity of the voice or dialogue from the center channel speakers in the system.
Flipping the switch to the “UP position engages the circuit and “DOWN” turns it off.
MOUNTING TO FLAT PANEL MOUNTING BRACKETS
There are additional mounting inserts on the rear of the speaker cabinet to facilitate attaching the sound bar
speakers to on wall flat panel mounts, see note figure 1. There are 6 threaded inserts provided that coincide with
the requirements of most manufactures mounts. Please check with your mount manufacture for applications and
compatibility.
TEATRO SOUND BAR SPEAKER SPECIFICATIONS
MODEL
T-V3.0
T-PC3.0
1” SOFT DOME x 3
-----
1” SOFT DOME x 3
1.5” SOFT DOME x 3
5.25” RPF x 3
52hz-22kHz
TWEETER
MIDRANGE
WOOFER
5.25” VDT x 3
55Hz-22kHz
91 dB
FREQUENCY
SENSITIVITY
IMPEDANCE
MAXIMUM POWER
DIMENSIONS
FINISH
89 dB
4 OHMS
4 OHMS
120 WATTS
150 WATTS
40” (W) x 7” (H) x 4 ½” (D) (5 ½” with bracket)
SATIN BLACK
25 LBS
GLOSS BLACK
30 LBS
WEIGHT
218-2082
Download from Www.Somanuals.com. All Manuals Search And Download.
|