Installation
& Operation Manual
Commercial Back Bar
Models BBRN & BBSN Series
Model BBRN40 Shown
Form No. 2322013
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
PrIor To InsTallaTIon
bottom, of the unit. Both drain ports come plugged
from the factory and can be removed if needed.
Uncrating and Inspection
Remove all crating material. Carefully inspect
cabinet for hidden damage. If damage is
discovered, file your claim immediately with the
transport company. Perlick is not responsible for
damage in transit.
NOTE: Remote units require evaporator
condensate to be plumbed to an external drain.
Electrical
The cabinet must be connected to a separately
fused power source (see Electrical Specification
Plate affixed to unit) in accordance with National
and Local electrical codes.
Do not cut cardboard
sleeve covering the unit.
Cutting may result in damage to the exterior
of the cabinet. Failure to follow this procedure
may damage the compressor and void
warranty.
CAUTION
Self-contained Perlick units come equipped with
a NEMA5-15P 90° plug with an 8’ cord extending
beyond the rear of the cabinet. The electrical
outlet must be flush with, or recessed into, the
wall surface.
1. Uncrate the unit on flat, level surface. Remove
the cardboard sleeve by removing the banding
securing the sleeve to the shipping base.
Carefully lift the cardboard sleeve up over the
top of the unit.
NOTE: Never use an extension cord to extend the
power cord to the electrical receptacle.
2. Carefully lift unit off the base and onto a hand
truck or dolly. Make sure unit is balanced
on transporting device using soft, flexible
strapping. Protect unit surfaces with cloth
material where strapping contacts unit.
Do not lift unit by drawer,
If unit has been laid on its
back or sides, place unit
upright and allow minimum of 24 hours before
connecting power. Failure to follow this
procedure may damage the compressor and
void the warranty.
CAUTION
CAUTION
shelving or door handles
or damage to the unit could occur.
Do not attempt to operate
the equipment on any
other power source than that listed on the
Electrical Specification Plate attached to the
unit.
CAUTION
To prevent personal
injury, two people
minimum required to lift the unit. Larger units
may require additional personnel.
WARNING
ELECTROCUTIONHAZARD!
Electrical grounding is
required. Appliances furnished with a 3-prong
(grounding) polarized plug are equipped for
your protection against possible shock
hazards.
DANGER
3. Before moving unit, secure door(s) to unit with
tape to prevent from opening.
4. Carefully move unit to installation site and
place in front of opening.
Finished flooring should
b e p r o t e c t e d w i t h
appropriate material to avoid damage from
moving the unit.
CAUTION
•
Never remove the round grounding prong
from the plug.
Never use a 2-prong adapter.
Never use extension cord to connect
power to the unit.
If a 2-prong receptacle is encountered, or
a longer power cord is required, contact
a qualified electrician to have it replaced
in accordance with applicable electrical
codes.
•
•
Plumbing
Do not over-tighten drain
fitting or damage to the
threads could occur.
•
CAUTION
Condensate from the cooling coil is automatically
evaporated from the condensate pan located in
the condensing unit housing on self-contained
models.
Failuretocomplywiththese
electrical guidelines may
result in possible death or serious injury, fire,
or loss of property.
DANGER
Each unit is equipped with a floor drain located
in the right rear corner of the cabinet. The drain
can be plumbed to an external floor drain by
connecting to the 3/4” NPT thread connection on
the side, or the 1” NPS thread connection out the
Printed in USA
3
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
InsTallaTIon
General Information
Installing the Unit
•
For units equipped with a power cord, the
cord and plug may be aligned with a recess in
the back panel to allow the unit to be pushed
closer to the wall. For correct alignment, the
wall outlet must be located 4” - 10” above the
floor.
If unit has been laid on its
back or sides, place unit
upright and allow minimum of 24 hours before
connecting power.
CAUTION
1. With power applied to the unit, check that
the lighting and cooling functions operate
properly, then turn off power to the wall outlet
and/or circuit breaker.
•
Floor must be level in area of installation.
Preparing the Space
2. Position the cabinet into place using rollers
when necessary.
Make sure the floor under
the unit is level with the
CAUTION
NOTE: Proper air flow around the condensing unit
is necessary for efficient operation. Never obstruct
the air flow in and out of the condensing unit.
surrounding finished floor. Protect a finished
floor with plywood, cardboard or some other
suitable material before moving the unit into
place. Failure to do this may result in damage
to the floor.
3. When cabinet is in place, check installation
with carpenter’s level. When the unit is level
front-to-back and side-to-side, accumulated
water will drain out of cabinet to evaporator
drain.
NOTE: If unit has been laid on its back or sides,
place unit upright and allow minimum of 24 hours
before connecting to a power source. Failure to
follow this procedure may damage the compressor
and void warranty.
4. Turn on power to the outlet and/or circuit
breaker.
1. Make sure the space opening is correctly
sized for the unit. See Dimension drawings at
the back of this manual for correct dimensions.
Electric Condensate Evapaway
(Optional)
For installation in areas of high humidity, a 115-
volt electric condensate pan can be installed
underneath the cabinet to collect and evaporate
the condensate from the cabinet evaporator. A 6’
3-prong plug is included.Aseparate circuit should
be provided for the heater. The kit can be used
only on cabinets equipped with 4” minimum legs;
it cannot be used on units equipped with platform
or base plate kits. Follow instructions supplied
with the kit.
NOTE: For a cabinet door to open properly, the
door must open a minimum of 90°. Use a minimum
3” filler in corner installations to assure a 90°
opening. Allow 24” clearance in front of the unit
for full door swing and shelf/drawer pull-out.
2. Check that the following are level and square:
•
•
Front and interior opening
Installation opening and floor surface
NOTE: The floor under the unit must be at the
same level as the surrounding finished floor.
Base Plate Installation (Optional)
Once the unit is secured in place, install the base
plate brackets to the cabinet bottom in the holes
provided. Attach base plate to brackets. Refer
to the installation instructions included with the
Base Plate Kit.
Casters or Legs
Refer to the instructions included with the Casters
or Legs Kit.
Printed in USA
4
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
Sealing Cabinet to Floor
Cabinet
For units without casters or legs, it may be
necessary to seal the base of the cabinet to
the floor. This can be accomplished by laying a
bead of silicone sealant between the base of the
Bead Silicon
Sealer (RTV)
Floor
Figure 1. Sealing Cabinet to Floor
Faucet and Dispensing Head Installation
Refer to the instructions included with the Faucet
and Dispensing Head Kit.
oPeraTIon
2. Place the bottle in the desired area for 24
hours. Refrain from opening the unit during
the testing period. After 24 hours, check
the temperature of the water. Adjust the
temperature accordingly using the procedures
on this page.
Refrigeration and Temperature Control
The cabinet is equipped with a heavy-duty
refrigeration system designed to automatically
maintain a storage temperature of approximately
38° F.
Allow a minimum of 24 hours for ambient
temperatureproducttoreachstoragetemperature.
Thefollowingfactorsaffecttheinternaltemperature
of the unit:
Draft beer should be stored at a temperature
between 32° – 38° F. The most common cause
of dispensing problems is improper temperature;
beer will foam at warmer temperatures.
•
•
•
Temperature setting
Room temperature where installed
Number of times the door is opened and
closed
Beer will freeze at temperatures lower than
30° F. When beer freezes, the alcohol in the beer
may separate and cause the beer to be cloudy
with an “off” taste.
•
•
•
•
•
Length of time door is left open
Style of door installed
Door gasket seal and condition
Amount of time the internal light is illuminated
Installation in direct sunlight or near a heat
source
The following chart shows how temperature
affects beer:
Interior Light
The unit is equipped with an interior LED light in
the upper front of the unit just inside the door or
drawer. The light illuminates when the manual
rocker light switch is turned on. The rocker light
switch is located behind the LED light on the inside
of the frame on either the right or left side (same
side as the compressor).
Checking Product Temperature
1. Toaccuratelycheckthetemperatureofproduct
stored in the refrigerated compartment, insert
an accurate thermometer into a plastic
unbreakable bottle, partially filled with water.
Tighten bottle cap securely.
Printed in USA
5
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
To change the Setpoint:
Digital Temperature Control
1. Press the SETbutton for more than 2 seconds.
C
F
2. The value of the setpoint will be displayed and
the “C” or “F” LED starts blinking.
3. To change the Set value, press the
or
SET
button within 10 seconds.
4. To memorize the new setpoint value, press
the SET key again, or wait 10 seconds.
Figure 2. Digital Temperature Controller
adjusTmenTs
1. Support the door in the open position as
Changing Door Swing Direction
NOTE: Changing the door swing direction is
not advisable if the door is not equipped with
a full length handle. Doing so may result in an
undesirable handle position..
2. Pull door to the side and then lower the door.
3. Remove top and bottom hinge brackets.
Hinge Kits
4. Remove the hole plugs from the top and
bottom hinge bracket mounting holes (Figure
4). Place the plugs in the holes on the opposite
side made vacant by removing the hinges in
step 3.
Part No. 67439R: Right Hinging
Part No. 67439L: Left Hinging
Tools Required
•
•
•
•
Large flat head screwdriver
Regular Phillips head screwdriver
Hinge Kit from Perlick
Hole plugs
Hinge brackets
and mounting
screws
Plastic putty knife
Procedure
SUPPORT
Hinge brackets
and mounting
screws
Pull door to
the side then lower door
Figure 4. Hinge Removal
Remove hinge pin
Figure 3. Door Removal
Printed in USA
6
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
5. Using the screws removed in step 3, install
the top and bottom hinge brackets from kit
Front panel
Hinge brackets
and mounting
screws
Hinge brackets
and mounting
screws
Corner screws need not be
removed to remove front panel
Figure 5. Hinge Installation
Figure 7. Removing Front Panel
6. Remove the top and bottom hinge brackets
for later use.
8. Insert bearing into door top hinge bracket
9. Insert V-block into door bottom hinge bracket
orientation of the V-block.
Hinge brackets
and mounting
screws
Bearing in
door top hinge
bracket
Door bottom bracket
6°
Orientation
V-block
Figure 6. Door Brackets
7. Removethefrontpanelfromthedoorassembly
by removing the inner mounting screws, 4 per
side, from the perimeter of the door assembly
(Figure 7). Rotate the front panel 180°. The
top becomes the bottom. Reattach using the
same screws and mounting holes.
BOTTOM VIEW
Figure 8. Bearing and V-Block
Printed in USA
7
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
10. Attach the top and bottom door hinges using
11. Place lower V-block into lower cabinet hinge
Top hinge
and screws
Insert top pin
into bearing
Bottom hinge
and screws
Figure 9. Door Hinges
Insert and tighten hinge pin
Figure 11. Installing Door
Shelving Adjustment
Completely empty shelf or
drawer before removing.
CAUTION
1. Open the door. Tilt the shelf and remove it
from the unit
V-block parallel
to cabinet
2. Reposition each bracket separately. Grasp
the middle of the bracket, pull the front end
up and out, then forward to remove it.
TOP VIEW
3. Place brackets at desired location and reinstall
shelf(s).
Figure 10. Installing V-Block
12. Lift door assembly and insert top pin into
bearing. Move door toward cabinet and align
13. Insert and tighten lower hinge pin to complete
assembly.
Figure 12. Shelf Bracket
Printed in USA
8
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
maInTenanCe
Never attempt to repair or
perform maintenance on
the unit until the main electrical power to the
unit has been disconnected!
the metal is passive and stainless. If the passive
film of stainless steel has been broken, equipment
starts to corrode and rust.
DANGER
There are three basic things which can break
down stainless steel’s passive layer and allow
corrosion to occur:
LED Light Replacement
•
•
•
Mechanical abrasion
Deposits and water
Chlorides
1. Open the door, or remove the upper drawer
(see Removing Drawer, Figure 15).
2. Using a flat blade screwdriver, carefully pry
off the lens cover.
Mechanical abrasion refers to the things that will
scratch a steel surface. Steel pads, wire brushes
and scrapers are prime examples.
3. Remove the two screws securing LED light to
housing.
Water comes out of the faucet in varying degrees
of hardness. Depending on what part of the
country you live in, you may have hard or soft
water. Hard water may leave spots. When allowed
to sit, these deposits will break down the passive
layer and rust stainless steel. Other deposits from
food preparation must be promptly removed with
an appropriate cleaning agent.
4. Unplug the LED from the wiring harness.
5. Plug new LED into harness and secure to
housing using screws removed in step 2.
6. Snap LED cover into place.
Unplug LED Light Strip
LED Light Strip
Chlorides are found nearly everywhere. They
are in water, food and table salt. Household and
industrial cleaners are the worst offenders.
Preventing Stainless Steel Rust
Use the proper tools. Use non-abrasive tools to
clean stainless steel products. Soft cloths and
plastic scouring pads will not harm the steel’s
passive layer.
Lens Cover
#6-32 x 3/8”
machine screw (Qty. 2)
Clean with polish lines. Some stainless steels
come with visible polishing lines or “grain”. When
visible lines are present, always scrub in a motion
parallel to the lines. When the grain cannot be
seen, play it safe and do not use a circular motion.
Polish in a consistent straight pattern.
Figure 13. Interior LED Light
Stainless Steel Care & Cleaning
General
Contrary to popular belief, stainless steel is
susceptible to rusting. Corrosion on metals is
everywhere. It is recognized quickly on iron
and steel as unsightly yellow/orange rust. Such
metals are called “active” because they actively
corrode in a natural environment when their atoms
combine with oxygen.
Use alkaline, alkaline chlorinated or non-chloride
containing cleaners. While many traditional
cleaners are loaded with chlorides, the industry
is providing an ever-increasing choice on non-
chloride cleaners. If you are not sure of chloride
content in the cleaner being used, contact your
cleaner supplier. If your present cleaner contains
chlorides, ask your supplier if they have an
alternative. Avoid cleaners containing quaternary
salt; it also can attack stainless steel and cause
pitting and rusting.
Stainless steel is a “passive” metal because it
contains other metals like chromium, nickel and
manganese that stabilize the atoms. Chromium
provides an invisible passive film that covers the
steel surface acting as a shield against corrosion.
As long as the film is intact and not contaminated,
Printed in USA
9
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
Keep food equipment clean. Use alkaline
chlorinated or non-chloride cleaners at
recommended strength. Clean frequently to avoid
build-up of hard, stubborn stains. The single most
likely cause of damage is chlorides in the water.
Remember, adding heat to cleaners that contain
chlorides dramatically increases their effect on
stainless steel.
Glass panels may be cleaned using any standard
glass cleaner available on the market.
To clean interior and exterior non-metallic surfaces
and removable parts, wash with a mild solution of
soap and lukewarm water with a little baking soda.
Rinse and dry thoroughly. Avoid getting water on
lights, controller and fan motors.
Cleaning the Condenser
Rinse, rinse, rinse! If chlorinated cleaners are
used, immediately rinse and wipe equipment and
supplies dry. The sooner you wipe standing water,
especially when it contains cleaning agents, the
better. After wiping equipment down, allow it to
air dry. Oxygen helps maintain the stainless steel
passive film.
The condenser (located behind front grille cover)
should be cleaned every three (3) months. Use
a soft bristle brush and vacuum to remove the
dust and lint.
Avoid damaging or
crushing the condenser
CAUTION
fins or tubing. Failure to follow this procedure
may damage the compressor and void the
warranty.
Cleaning Cabinet Interior/Exterior
NEVER use hydrochloric
CAUTION
acid (muriatic acid) on
stainless steel. Do not use abrasive cleansers
or cloths on any interior or exterior surfaces
or removable parts.
Printed in USA
10
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
Recommended Cleaners for Specific Situations
Job
Cleaning Agent
Comments
Routine cleaning.
Soap, ammonia, detergent
Apply with sponge or soft cloth.
Fingerprints and smears.
Areal 20, Lac-O-Nu, Lumin Wash,
O’Ceder Cream Polish
Provides barrier film to minimize finger-
prints. Can be used on all finishes. Rub
the surface with a cloth as directed on
the package.
Stubborn stains and discolorations.
AllChem Concentrated Cleaner, Samae, Apply with a damp sponge or cloth, then
Twinkle, Cameo Copper Cleaners, Grade rinse with clear water and wipe dry.
FFF Italian Pumice Whiting, Steel Bright,
Lumin Cleaner, Zud Restoro, Sta-Clean,
Highlite Cooper’s Stainless Steel Cleaner
or Revere Stainless Steel Cleaner.
Old Dutch, Lighthouse Sunbrite, For these household cleaners, rub with
Wyandotte Bab-O, gold Dust, Sapollo, a damp cloth. They may contain chlorine
Bon Ami or Comet.
bleaches so rinse thoroughly after use
and wipe dry
Liquid NuSteel or Dubois Temp
For these products, rub the surface with
a dry cloth using only a small amount of
cleanser. Rinse with water and dry.
Heat tint or heavy discoloration.
Penny-Brite, Copper Brite, Paste Nu- Rinse and rub onto surface with a dry
Steel, Dubois Temp or Tarnite cloth.
Bar Keepers Friend, Revere Stainless When using these cleaners, apply with a
Steel Cleaner, Allen Polish, Steel Bright damp sponge or cloth, rinse thoroughly
Wyandotte Bab-O or Zud.
and wipe dry.
Tenacious deposits, rust, discoloration, Oakite No. 33 Dilac, Texo NY, Flash- Use Swab and soak with a clean cloth. Let
industrial atmospheric stains.
Klenz Caddy Cleaner, Turco Scale 4368 stand for 15 minutes or more according
or Permag 57.
to directions on package then rinse and
wipe dry.
Rust discoloration or corrosion caused
by cleaning agents containing hydro-
chloric (muriatic) acid or chlorine bleach
3M Scotch Brite pad, typeAGrade “Fine” Clean off the surface soil using cleaning
methods above. Then rub discolored or
corroded areas lightly with dry pad.
Use of property names is intended only to indicate a type of cleaner and does not constitute an endorsement. Omission of any proprietary
cleaner does not imply its inadequacy. All products should be used in strict accordance with instructions on the package.
NOTE: Do not use steel wool or scouring pads to clean stainless steel.
Printed in USA
11
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
TroubleshooTInG
Before Calling For Service
If the unit appears to be malfunctioning, read through the Operation section in this manual first. If the
problem persists, check through this troubleshooting section. Locate the problem and refer to the cause
and remedy before calling for service. The problem could be something that can be solved without a
service call.
Never attempt to repair or perform maintenance on the unit until the main electrical
power to the unit has been disconnected!
DANGER
Problem
Cause
Rocker switch in Off position.
LED board inoperable.
Manual switch on.
Solution
No interior light.
Turn switch on.
Contact your selling dealer.
Turn manual switch off.
Light stays on when door is
closed.
Noisy operation.
Soft sounds from compressor, fan
motor and valves heard.
Normal operation.
LED Controller display is flashing Thermostat probe failure.
.“P1”.
Contact your selling dealer.
LED Controller display is flashing Internal compartment has exceeded the Make sure door is completely closed.
“HA”. high temperature alarm preset value for Check door gasket seal. Replace if
over 30 minutes.
necessary.
Check condenser and clean if necessary.
Make sure louvered plate is unobstructed.
If surrounding ambient temperature has
changed dramatically recently, compartment
temperature may be affected.
Make sure interior light is off.
Warm product placed in cabinet recently. Wait
24 hours for product to chill then recheck
temperature.
LED Controller display is flashing Internal compartment has exceeded the Make sure door is completely closed.
“LA”. low temperature alarm preset value for Check door gasket seal. Replace if
over 30 minutes.
necessary.
If surrounding ambient temperature has
changed dramatically recently, compartment
temperature may be affected.
LED Controller display is flashing Controller has a data or memory failure. Reset both compartment presets.
“EE”.
If problem persists, contact your Perlick
Service Department.
Unit is not running.
No power to the unit.
Condenser dirty.
Home circuit breaker tripped. Reset circuit
breaker.
ON/OFF keypad is off. Turn on.
Clean the condenser.
Compartments are warmer than
usual.
Control preset not set properly.
Light staying on.
Reset compartments presets.
Turn manual light switch off.
Condenser dirty or obstructed.
Clean condenser and clear obstruction.
Door is open or has been opened more Wait 24 hours and recheck temperature.
frequently lately.
Internal louvers and/or fan guard
obstructed.
Reset preset temperature if necessary.
Make sure louvers and/or fan is not
obstructed.
Warm product placed in cabinet
recently.
Printed in USA
12
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
Problem
Cause
Solution
System runs for long period of
time.
Condenser dirty or obstructed.
Door kept open for long time or opened Wait 24 hours and recheck temperature.
more frequently. Reset preset temperature if necessary.
Clean condenser and clear obstruction.
Warm product place in cabinet recently. Normal for system to run more frequently.
Hot day and warm room temperature.
Condensation forms inside the
compartments.
High humidity and/or frequent door
opening.
Normal operation.
Door not closing and sealing properly.
Make sure door is closing properly. Check
door seals and replace if necessary.
Condensation forms on outside
of unit.
High humidity and/or frequent door
opening.
Normal operation.
Door not closing and sealing properly.
Make sure door is closing properly. Check
door seals and replace if necessary.
If condensation persists, contact your selling
dealer.
For Product Information
For Replacement Parts and Accessories
•
•
•
Contact your selling dealer.
•
Use only genuine Perlick replacement parts
and accessories. Genuine Perlick parts and
accessories are designed to work correctly
with Perlick products and offer superior
service life. The use of non-Perlick parts can
damage the unit and may void the warranty.
Check the model and serial number of your
unit which is located on the right or left interior
panel. Call your Perlick Factory Authorized
Service Center.
Call (800) 558-5592 for factory assistance on
planning installation or product information.
Write to Perlick Corporation, Customer
Service Department, 8300 West Good Hope
Road, Milwaukee, WI 53223.
•
•
•
•
Email us at [email protected].
For Product Service
•
•
Check the model and serial number of your
unit located on the label attached to the inside
top of the cabinet.
(800) 558-5592.
(800) 558-5592.
Printed in USA
13
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
dImensIons
Printed in USA
14
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
Printed in USA
15
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
Printed in USA
16
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
WIrInG dIaGrams
Printed in USA
17
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
Printed in USA
18
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
Printed in USA
19
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
WarranTy
The terms and conditions set forth below
LOST and DAMAGED MERCHANDISE
together with those appearing on the face of
the Acknowledgement (the “Order”) constitute
the complete and exclusive agreement between
Perlick Corporation and the Buyer pertaining to
the goods and/or services identified in the Order.
If there is a discrepancy or conflict between any
exhibit or supplement to the Order and these
terms and conditions, these terms and conditions
shall control. The Order is intended by Seller and
Buyer to be the complete, exclusive, and final
statement of their agreement. Any changes to an
Order must be in writing and signed by Perlick
and Buyer.
THE RESPONSIBILITY OF THE PERLICK
CORPORATION CEASES UPONACCEPTANCE
OF ITS PRODUCTS BY THE CARRIER. Any
damage or loss sustained in shipment is the
carrier’s responsibility. Before giving the carrier
a clean receipt at time of delivery, make sure you
receive every item on the bill and inspect every
carton, crate and box for concealed damage,
i.e., broken boards, crushed or punctured
cartons, torn cardboard. IF ANY ITEMS ARE
SHORT OR DAMAGED, DO NOTACCEPT THE
SHIPMENT UNLESS THE CARRIER MAKES A
NOTATION OF THIS ON YOUR FREIGHT BILL.
Then request an inspection. Do not destroy the
packing materials. If their agent does not make
an inspection within five days, advise the carrier
via letter that you notified them regarding the
matter and they have failed to act. You will need
this letter to support your claim. Then file a claim
for your loss. When you give the carrier a clean
receipt, you accept the total responsibility for the
shipment. UPS shipments are insured individually
and UPS will replace all merchandise that is lost
or damaged.
TERMS NET 30 DAYS
Payment by Visa, MasterCard,American Express
or Discover card accepted or cash in advance
unless prior accommodations have been made
with our Credit Department. Please direct inquiries
for detailed information to our Credit Manager.
All sales, excise, or similar taxes required by
law to be collected or paid by seller shall be in
addition to prices quoted unless an appropriate
Tax Exemption certificate is furnished. All goods
are sold F.O.B. factory. Except for otherwise
provided, Perlick will not be responsible for freight,
transportation, insurance, shipping, storage,
handling, demurrage or similar charges. Invoices
are payable in full in thirty (30) days following
the invoice‚s date of issuance. If by the terms
of sale credit is extended, Perlick reserves the
right to revoke such credit if buyer fails to pay
for any products when due and may demand
payment prior to the commencement of any
further shipment.
RETURN OF MERCHANDISE
Do not return any merchandise without our
approval. Merchandise returned without a return
merchandise authorization number will not be
accepted at Perlick. Used, discontinued, and
certain custom made items cannot be returned for
credit. These custom items include non-catalog
products (specials) as well as custom assembled
catalog products. Catalog items are designated
as non-returnable on the price list page on which
they appear. Items returned must be in new
condition and packaged in their original carton
or crate. Freight charges must be prepaid on all
return shipments.
WAIVER
Any waiver of strict compliance with the provisions
of an Order must be in writing. No such waiver
shall be construed as a waiver of any other term
or condition except as provided in writing, nor as
a waiver of any subsequent breach of the same
term or condition.
When a return is authorized, a credit may be
allowed pending an examination of the returned
goods. The amount of the restocking charge will
depend on the condition of the equipment. The
minimum restocking charge for glass washers,
bottle coolers, frosters, direct draws, cooler
series back bars and accessory parts is 20%.
The minimum restocking charge for custom
series cabinets is 50%. The minimum restocking
METHOD OF SHIPMENT
All shipments are carefully packed and labeled.
Crates, boxes and cartons used are of approved
weight and strength. Freight rates are based upon
100 pound minimum.
Printed in USA
20
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
charge for un-assembled, freestanding underbar
stainless steel modules is 20%.Assembled under
bar modules are considered custom products
and are not returnable for credit. The restocking
charge on the item returned is either a percentage
of the value of the item or $35.00, whichever is
greater.
ONE YEAR LABOR WARRANTY
In addition to Perlick’s one year parts warranty
and five year compressor warranty,ALLPERLICK
REFRIGERATION SYSTEMS are offered with
a one year labor warranty at no extra charge.
Perlick’s one year labor warranty provides
that Perlick will pay for the cost of any labor to
replace any defective part for up to one year
after installation, subject to the following terms
and conditions:
ONE YEAR PARTS WARRANTY
Perlick products are guaranteed against defects
in both material and workmanship for a period of
one year from date of sale. Defective parts will be
replaced on a no-charge basis, F.O.B. our factory,
when adjudged defective upon inspection. We are
not responsible for parts damaged by alteration,
unauthorized service, accident or abuse.All costs
associated with replacement, including freight,
labor and/or loss of sales, are the responsibility
of the user..
(A) Parts returned to Perlick shall be returned
freight prepaid and shall be identified with
Perlick’sserialnumberandreturnauthorization
number.
(B) Improper operation due to voltage variances,
inadequate wiring and physical damage is the
responsibility of the purchaser. They are not
manufacturing defects.
(C) Condenser coils shall be cleaned regularly.
Failure to provide an adequate flow of cooling
air will void this warranty.
(D) Factory-specified maintenance and installation
will be provided by the selling dealer who shall
also be responsible for the installation and set-
up of these products in accordance with local
plumbing, refrigeration and electrical codes.
Perlick’s one year labor policy applies to the
United States and Canada. IT DOES NOT
APPLY TO REFRIGERATION SYSTEMS
ADDED BY OTHERS (remote systems) or any
part which has been subject to misuse, neglect,
alteration, accident, or to any damage caused
by transportation, flood, fire or other acts of God.
Printed in USA
21
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBRN/BBSN Installation & Operation Manual
noTes
Printed in USA
22
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
Models BBR/BBS Installation & Operation Manual
noTes
Printed in USA
23
0213
Download from Www.Somanuals.com. All Manuals Search And Download.
8300 West Good Hope Road • Milwaukee, WI 53223 •
Download from Www.Somanuals.com. All Manuals Search And Download.
|