Pelco Welder C1498M B User Manual

DD5TA Series

Dome Drive

Installation/

Operation Manual

C1498M-B (7/99)

LISTED

Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108

International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 • DataFAX (1-559) 292-0435

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS AND WARNINGS

Observe the following warnings before installing and using this product.

1. Installation and servicing should only be done by qualified service personnel and

conform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P

enclosure, it is designed for indoor use only and it must not be installed where

exposed to rain and moisture.

3. Only use replacement parts Pelco recommends.

4. After replacing or repairing this unit’s electrical components, measure the resistance

between the line and exposed parts to verify the exposed parts have not been

connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the

weight of the enclosure, pan and tilt, camera and lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompany-

ing this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation

and operation.

DESCRIPTION

Dome drives in the DD5TA Series are part of the SpectraLite™ dome system (refer to

Figure 1). The dome drives can do the following:

BACK

BOX

•

360° pan rotation

preset positioning

+2 to -92° tilt

variable speed

DOME

DRIVE

All dome drives include a color CCD camera with a 16X zoom lens and capability to focus

when going to a preset position. An integral receiver has a switch to select the type of

control. The receiver supports Coaxitron^®and RS-422 control types. The dome operates on

24 VAC. The dome drive is quickly installed and removed from the back box without tools.

LOWER

DOME

MODELS

Figure 1. System Compo-

nents (In-Ceiling

DD5TAC

DD5TAC-X

Dome drive with color camera and lens, NTSC standard (FCC, UL, cUL)

Dome drive with color camera and lens, PAL standard (CE)

Model Shown)

INSTALLATION

1. Turn on power to the back box. The red LED should light to indicate power. If the LED

does not light, correct the trouble before proceeding. (Refer to the Troubleshooting

section of the SD5 Series Spectra II™ and Spectra Lite™ Dome Installation/Operation

manual.) If the light operates, you may either leave power on or turn it off before

continuing the installation.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Set the switches on the bottom of the dome drive. Refer to Table A for the settings for

SW1, and Table B and Table C for SW2.

3. Install the dome drive in the back box. Line up the green tab and red tab on the dome

drive with the green label and red label on the back box. Raise the dome drive into the

back box and push on the ends of the tabs until they both click into place on the back box.

CAUTION: Make

sure the dome

drive locks into

place. Pull down on the

dome drive with moderate

pressure to ensure that it

stays in place.

4. Turn on power, if it is not on. Listen for the fan operating. If the fan does not work, the

dome will overheat and shut down. If the fan does not work, return the back box

electronic assembly and dome drive to the factory for repair. Refer to the Back Box

Electronic Assembly Removal section in manual C1487M-C.

Table A. Switch Settings for SW1

Control Type

Switch Setting

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

Coaxitron^®

P-Type Control

D-Type Control

OFF

OFF*

OFF**

NOTES: Switches SW1-3 through SW1-6 MUST be OFF.

D-type control is RS-422 that is compatible with Pelco‘s CM6700, MPT9500 and CM8500

controllers or with American Dynamics control systems using the AD2083 Translator.

P-type control is RS-422 that is compatible with Pelco's CM6700/CM9750/CM9760 control

systems.

* OFF - Use with controllers that have more than 32 presets.

ON - Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

For CM9502 with fixed speed keyboards, set switch OFF.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

Table B. Switch Settings for SW2 – P-Type Control

NOTE: For Coaxitron^®controls, SW2 is not used; set all switches OFF.

For D-type control systems, refer to Table C.

Receiver Address

Switch Setting

SW2-3

Baud

Switch Setting

SW2-1

SW2-2

SW2-4

SW2-5

Rate SW2-6 SW2-7 SW2-8

OFF

2400 OFF

4800 ON

9600 OFF

OFF

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Switch Settings for SW2 – D-Type Control

NOTE:

For Coaxitron^®controls, SW2 is not used; set all switches OFF.

For P-type control systems, refer to Table B.

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

(Continued on next page)

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Switch Settings for SW2 – D-Type Control (Continued)

NOTE:

For Coaxitron^®controls, SW2 is not used; set all switches OFF.

For P-type control systems, refer to Table B.

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

100

101

102

103

104

105

106

107

108

109

110

111

112

OFF

(Continued on next page)

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Switch Settings for SW2 – D-Type Control (Continued)

NOTE:

For Coaxitron^®controls, SW2 is not used; set all switches OFF.

For P-type control systems, refer to Table B.

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

OFF

(Continued on next page)

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Switch Settings for SW2 – D-Type Control (Continued)

NOTE:

For Coaxitron^®controls, SW2 is not used; set all switches OFF.

For P-type control systems, refer to Table B.

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

OFF

(Continued on next page)

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Switch Settings for SW2 – D-Type Control (Continued)

NOTE:

For Coaxitron^®controls, SW2 is not used; set all switches OFF.

For P-type control systems, refer to Table B.

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

OPERATION

The red LED in the back box interconnect door lights when power is turned on, and the fan

exhausts heat from inside the back box when the dome drive is installed. If you have an

outdoor pendant model with a heater, heater elements in the back box turn on at 70°F

(21°C) and off at 85°F (29°C). The heater element in the lower dome turns on at 40°F (4°C)

and off at 60°F (16°C). The interconnect door fan and heater fans in the outdoor back box

operate continuously.

POWER-UP DISPLAY

When the dome is powered up or reset, the monitor displays the selected protocol, revision

number, and other information, which remains until the dome moves. The information

displayed depends on the selected protocol and the choice made on the menu for

selectable power-up mode. As a default, the dome goes to a random position.

NOTE: The dome will stop

operating if voltage at the

dome drops below 18 VAC.

It will turn back on and go

through its start-up routine

when the voltage exceeds

18 VAC.

The control system protocol (C, D, or P) appears. C is for Pelco’s Coaxitron^®control

system. D-type control is RS-422 compatible with Pelco’s CM6700, MPT9500, and CM8500

controllers or with American Dynamics control systems using the AD2083 Translator. P-type

control is RS-422 compatible with Pelco’s CM6700 and CM9750/CM9760 control systems.

For D and P protocols, the device address, baud rate, parity (N), number of data bits (8), and

number of stop bits (1) appears. For D protocol, “32 presets” appears if the 32-preset mode is

selected (SW1-7 ON). “CM9500 mode” appears if CM9500 mode is selected (SW1-8 ON).

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

PAN AND TILT FUNCTIONS

Use your controller’s joystick to control pan and tilt operation.

•

Fixed-Speed Controllers – Pan and tilt operation is at a fixed speed; the controller

determines the speed.

Variable-Speed Controllers – Depending on the joystick’s position, standard pan

operation ranges from 0.5 to 80 degrees per second (dps); standard tilt operation

ranges from 0.5 to 40 dps. When performing preset operations, pan speed is 250 dps;

tilt speed is 200 dps. In turbo mode, pan speed is 150 dps, while turbo mode does not

affect tilt speed.

AUTO FLIP

When the camera tilts down and just beyond vertical, the dome rotates 180 degrees. When

the dome rotates (flips), the camera starts moving upward while you continue holding the

joystick in the down position. Once you release the joystick after the dome rotates, joystick

control returns to normal operation. Auto-flip is useful for following someone who passes

directly beneath the camera.You can disable this feature in the auto flip programming menu.

SCAN SPEED

Scan speed is adjustable from 1 to 40 degrees per second through the programming menu.

ZOOM

The SpectraLite™ dome can magnify an object up to 16 times (16X of optical zoom).

Zoom Telephoto – Press and hold down the Zoom Tele button or turn the joystick

clockwise until you have the picture you want.

Zoom Wide – Press the Zoom Wide button or turn the joystick counterclockwise to

increase the field of view.

PRESET FUNCTIONS

The SpectraLite™ dome can go to 32 preset locations, each with a 20-character label.

Presets are numbered 1-32. Refer to your control system documentation for programming

presets.

NOTE: For American

Dynamics controllers with

only 32 presets, set switch

SW1-7 on the dome drive in

the ON position. When

SW1-7 is ON, preset

When doing a preset operation, the amount of error in moving to the pan and tilt positions is

1/2 degree.You may get erratic operation if you command the dome to go to an undefined

preset.

99 becomes 32

98 becomes 31

97 becomes 30

96 becomes 29

95 becomes 28

94 becomes 27

93 becomes 26

92 becomes 25

91 becomes 24

90 becomes 23

Presets 33 and 34 are fixed commands (you cannot program them). Preset 33 is the “flip”

command, which pans the dome drive 180 degrees from its current position. Preset 34 is

the “pan zero” command, which directs the dome drive to the factory-determined zero

reference point. The following presets are reserved for special functions.

Preset

Function

Park

90-93

Flip command

Pan zero command

Limit stops

Select camera programming menu

Stop a scan

If the limit stops are turned

off (refer to the Limit Stops

section), presets 23-26 can

be used as regular presets.

97-99

Activate scanning

In the following sections, sometimes a number in parentheses follows a preset. This second

number is for 32-preset mode (conversion that lets Pelco’s presets work with American

Dynamics controllers). If you are using an American Dynamics controller, use the number in

parentheses.

RANDOM, FRAME, AND AUTO SCANNING

Program preset 97 (30) to start random scanning. Program preset 98 (31) to activate frame

scanning (three seconds of scanning followed by a three-second pause). Program preset

99 (32) to start auto (continuous) scanning.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Software controls scan limit stops. When the dome reaches one, it immediately reverses

direction. Refer to the Limit Stops section to program the scan limit stops. Program preset

96 (29) to stop a scan. Any pan and tilt or lens command also stops a scan.

PARK

If the dome does not receive any commands for a specified period, it goes to preset 1 and

parks. The dome will not park if the time specified is zero or preset 1 has not been

programmed. The default is zero minutes.

PROGRAMMING THE SPECTRALITE™

The dome can be programmed for the following functions:

AGC (automatic gain control)

Auto flip disable

Camera reset

Gain

Scan speed

Sharpness

Auto focus

Auto park time

Backlight compensation

Limit stops

Power line synchronization

Power-up mode

Shutter speed

White balance

The main menu contains four secondary menus: Camera, Line Sync, Power Up, and Other.

Each secondary menu has submenus, which are structured as follows:

1. Camera

First Camera Submenu

Backlight comp

Reset camera

Gain/AGC

Second Camera Submenu

Shutter speed

Auto focus mode

Sharpness

AGC mode

Sharpness

Gain

White balance

Auto-iris

Auto white bal

Auto-iris mode

Auto-iris level

White bal hue

Prev (to first camera submenu)

Next (to second camera submenu)

2. Line Sync

3. Power Up

Power up

4. Other

Line sync

Auto flip

Line sync phase

Limit stops

Park time minutes

Scan speed deg/s

The following sections explain how to program the SpectraLite™ dome using the menu choices.

MAIN MENU ACCESS

You can call up the main menu on your monitor by programming (setting or creating) preset

95 (28). Programming preset 95 for Pelco’s controllers varies according to the type of

controller you are using. Below are instructions for programming preset 95 for various Pelco

controllers.

CM6700

1. Enter the number of the SpectraLite™ camera and press the CAM key.

2. Enter 95 and hold the PRESET key for two seconds.

3. In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.

CM8500

1. Enter the number of the SpectraLite™ camera and press the CAM key.

2. Highlight PRESET in the Camera menu and hold down the joystick button until the Set

Presets prompt appears.

3. Enter 95 and press the PRESET key. The main menu appears.

CM9500

1. Enter the number of the SpectraLite™ camera and press the CAM key.

2. Press the SELECT key twice.

3. Highlight CAM in the Setup menu and press the SELECT key.

4. Highlight PRESET in the Camera menu and press the SELECT key.

5. Enter 95 and press the F1 key. The main menu appears.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

CM9750

1. Turn the KEY SWITCH to the ON position.

2. Press the PROG key. PROGRAM appears on the LCD screen.

3. Press the PRES key. The PRESET prompt appears.

4. Enter 95 and press the ENTER key. The main menu appears.

5. Turn the KEY SWITCH to the OFF position.

CM9760

1. In the default menu, select DEF. The Define Submenu appears.

2. Enter your four-digit PIN.

3. Enter 95 and select PRST. The main menu appears on the monitor.

4. Select the Quit icon to return to the default menu.

MPT9500

Standard Coaxitron^®Mode

1. Enter 95 and press the PRESET SET key.

2. Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron^®or RS-485 Mode

1. Enter 95 and press the PRESET SET key.

2. Press the F2 key. The main menu appears.

BACKLIGHT COMPENSATION

The two backlight compensation modes are on and off. Backlight compensation lets the

dome compensate for bright light behind the object you want to view. With backlight

compensation ON, the dome uses only the center 10 percent of the picture for adjusting the

iris (refer to Figure 2). A bright light source outside this area washes out to white. The

camera adjusts the iris so the object in the sensitive area is properly exposed. To change

the backlight compensation mode:

NON-SENSITIVE AREA

SENSITIVE

AREA

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Backlight Comp.

4. Press the Iris Open button. The cursor moves to the right beside the word On or Off.

5. Move the joystick up or down to toggle between On and Off.

Figure 2. Backlight

6. SELECT – Press the Iris Open button to select your choice.

Compensation

CANCEL – Press the Iris Close button if you do not want to change the setting.

RESET CAMERA

Resetting the camera returns the following settings to their defaults.

Setting:

Auto-focus mode

Gain/AGC

Default:

Auto

AGC mode

Gain

Backlight comp

Auto-iris

Auto

No default setting

Off

Mode

Auto

Level

Default value depends on type of camera

Auto

Shutter speed

White balance

Auto white balance

White balance hue

Sharpness

No default setting

The following settings are not reset when the camera is reset: park time, auto flip disable,

and limit stops.

Turning off power to the dome does not reset the camera. Camera settings are retained in memory,

and when power is restored, the settings are the same as when the camera was turned off.

To reset the camera:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Reset Camera.

4. Press the Iris Open button to reset the camera.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

GAIN/AGC

AGC Mode

The two AGC (Automatic Gain Control) modes are auto and off.

•

In auto mode, the dome automatically adjusts the gain–the amount of amplification the

camera places on its video information to obtain a full 1-volt peak-to-peak video signal

out. If the iris is manually opened to its wide-open position and the picture is weak, the

AGC can be turned off and the gain increased manually to improve the picture. When

you close the iris, the AGC turns back on automatically when the lens iris starts closing.

•

In off mode, the AGC is off.

To change the AGC mode:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Gain/AGC.

4. Press the Iris Open button to enter the Gain/AGC submenu.

5. Move the joystick up or down to position the cursor beside AGC mode.

6. Press the Iris Open button. The cursor moves to the right beside the word Auto or Off.

7. Move the joystick up or down to choose between Auto or Off.

8. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

Gain

Gain adjusts the signal level of the video output. Increasing the gain in low light conditions

increases the noise level in the picture. To change the gain:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Gain/AGC.

4. Press the Iris Open button to enter the Gain/AGC submenu.

5. Move the joystick up or down to position the cursor beside Gain.

6. Press the Iris Open button. The cursor moves to the right beside the current gain

setting (a numeric value).

7. Move the joystick up or down to change the gain (making the picture on your monitor

get brighter or darker).

8. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

AUTO IRIS

There are two settings for auto iris: mode and level.

To change the settings for auto iris:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Auto-Iris.

5. Press the Iris Open button. Another menu will appear with auto iris mode and level

selections.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Move the joystick up or down to position the cursor beside one of the choices. Press

the Iris Open button.

MODE – The cursor moves to one of two choices: Auto or Off. In the Auto mode, the iris is

automatically adjusted to produce a constant video output as determined by the Level

setting below. In the Off mode, auto iris is disabled, and control is always manual. Move the

joystick up or down to toggle between Auto and Off. Press the Iris Open button to select the

choice, or press the Iris Close button if you do not want to change the setting.

LEVEL – The cursor moves to a numeric value, which the Spectra Lite™ dome uses to try

to maintain a certain light level. Changing the value of the Level setting will change the

video level to which the auto iris adjusts. This setting should be adjusted if the video level in

the auto iris mode is too bright or too dark. Move the joystick up or down to a value.

If auto iris is in the auto mode, it remains that way until you manually open or close the iris.

The dome will return to auto iris when it is panned or tilted more than 15 degrees.

If there is not enough light for a good picture when the iris is wide open, you can increase

the gain of the camera to improve the picture. To do this:

1. Hold down the Iris Open button until the iris is wide open.

2. Release the button.

3. Within one second, hold down the button again. This will start increasing the camera

gain. Hold down the button until you get a desirable picture or reach the maximum gain.

SHUTTER SPEED

There are seven electronic shutter speeds:

Auto

1/125

1/500

1/1,000

1/10,000

1/2,000

1/4,000

In the Auto setting the camera controls the shutter speed automatically. Increasing the

shutter speed lowers the light sensitivity, but rapidly moving objects will be less blurred as

the speed is increased. To change the electronic shutter speed settings:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Next.

4. Press the Iris Open button to go to the next camera submenu.

5. Move the joystick up or down to position the cursor beside Shutter Speed.

6. Press the Iris Open button.The cursor moves to the right beside the current shutter speed.

7. Move the joystick up or down to choose the shutter speed.

8. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

AUTO-FOCUS MODE

The two auto-focus modes are auto and off.

•

If auto focus is in auto mode, pressing the Focus Near or Focus Far button places the

focus in manual mode. The dome returns to auto focus if you pan or tilt the unit or do a

zoom function.

•

If auto focus is set to off, the dome operates in manual mode with one exception. If you

issue a command to go to a preset, auto focus turns on and remains on until you

press the Focus Near or Focus Far button.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

To change the mode:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Next.

4. Press the Iris Open button to go to the next camera submenu.

5. Move the joystick up or down to position the cursor beside Auto-Focus Mode.

6. Press the Iris Open button. The cursor moves to the right beside the word Auto or Off.

7. Move the joystick up or down to toggle between Auto and Off.

8. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

SHARPNESS

To manually adjust the picture sharpness:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Next.

4. Press the Iris Open button to go to the next camera submenu.

5. Move the joystick up or down to position the cursor beside Sharpness.

6. Press the Iris Open button to move the cursor to the right beside the value.

7. Move the joystick up or down to a value. As you change the value, you can see the

sharpness change. Press the Iris Open button to select the value, or press the Iris

Close button if you do not want to change the setting.

WHITE BALANCE

The two white balance settings are auto and white balance hue. To change the white

balance setting:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.

2. Press the Iris Open button to enter the Camera submenu.

3. Move the joystick up or down to position the cursor beside Next.

4. Press the Iris Open button to go to the next camera submenu.

5. Move the joystick up or down to position the cursor beside White Balance.

6. Press the Iris Open button. Another menu appears with the auto and white balance

hue selections.

7. Move the joystick up or down to position the cursor beside one of the choices. Press

the Iris Open button.

AUTO WHITE BALANCE – Move the joystick up or down to toggle between the Auto

and Off choices. Press the Iris Open button to select one, or press the Iris Close button if

you do not want to change the setting.

WHITE BALANCE HUE – Adjust the color by moving the joystick up or down to a value

between 1 (blue end of the spectrum) and 99 (red end). Hold the joystick up or down to fast

forward or fast reverse through the values. As you change the value you can see the color

change on your monitor. Press the Iris Open button to select the value, or press the Iris

Close button if you do not want to change the setting. If Auto White Balance is on, it

changes to off when you select a new value.

LINE SYNCHRONIZATION

You can turn line synchronization on or off.

•

If it is on, you can adjust the synchronization of the power line voltage so it is in phase

with other cameras. If cameras are out of phase with each other, they may produce

what appears to be vertical roll when switching between cameras.

•

If it is off, the dome synchronizes to an internal clock.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

To change the line synchronization settings:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Line

Sync.

2. Press the Iris Open button. Another menu appears with the Line Sync and Line Sync

Phase selections.

3. Move the joystick up or down to position the cursor beside one of the choices.

LINE SYNC – Move the joystick up or down to toggle between On and Off. Press the Iris

Open button to select the choice. If you changed to Off, the camera may reset itself as it

adjusts to the new synchronization. If the camera resets, it only affects line synchroniza-

tion–it will not change any other camera parameters, such as auto focus or auto iris. Press

the Iris Close button if you do not want to change the setting.

LINE SYNC PHASE – Move the joystick up or down to change the numeric value. The

value represents the phase angle in tenths of a degree between 0 and 350 degrees (for

example, 900 is 90 degrees; 2400 is 240). Press the Iris Open button to select your choice.

The Line Sync setting will change to On. The camera may reset or the picture on your

monitor may wiggle when you change the phase angle. If the camera resets, it only affects

line synchronization–it will not change any other camera parameters, such as auto focus or

auto iris. Press the Iris Close button if you do not want to change the setting.

POWER-UP MODE

This feature lets the dome resume a desired condition following power-up. The menu

includes the following choices:

•

Default – On power-up, the dome goes through a configuration cycle and stops at zero

reference, showing “Configuration Done,” address, and mode settings on the screen.

Park – The dome moves to preset 1 when the power-up sequence finishes. The only

text on the screen is the preset label (if any).

Scan Auto – The dome initiates scan mode when the power-up sequence finishes.

Again, there is no text.

•

Scan Frame – The dome initiates a frame scan when the power-up sequence finishes.

Scan Rand – The dome initiates a random scan when the power-up sequence finishes.

The default setting is Default. To select the power-up mode:

1. On the main menu, move the joystick up or down to position the cursor (>) beside

Power Up Mode.

2. Press the Iris Open button to enter the Power Up Mode submenu.

3. Press the Iris Open button to move the cursor to the right.

4. Move the joystick up or down to cycle through the selections. Stop on the item you

want to select.

5. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

AUTO FLIP

The two auto flip modes are on (auto flip enabled) or off (feature disabled). To change the

auto flip mode:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Other.

2. Press the Iris Open button to enter the Other submenu.

3. Move the joystick up or down to position the cursor beside Auto Flip.

4. Press the Iris Open button. The cursor moves to the right beside the word On or Off.

5. Move the joystick up or down to toggle between On and Off.

6. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMIT STOPS

The two types of limit stop are manual and scan. When manual limit stops are set, a manual

(joystick) pan operation stops when a limit is reached. When scan limit stops are set, the

dome reverses direction during random, frame, and auto scanning when a limit stop is

reached. Software controls limit stops. To set limit stops:

1. Turn on limit stop mode.

2. Program the limit stops.

Turning Limit Stops On or Off

To change the limit stop mode:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Other.

2. Press the Iris Open button to enter the Other submenu.

3. Move the joystick up or down to position the cursor beside Limit Stops.

4. Press the Iris Open button. The cursor moves to the right beside the word On or Off.

5. Move the joystick up or down to toggle between On and Off.

6. SELECT – Press the Iris Open button to select your choice.

CANCEL– Press the Iris Close button if you do not want to change the setting.

Programming Limit Stops

MANUAL LIMIT STOPS

Refer to the documentation for your control system for programming presets, then do the

following:

NOTE: Programming

preset 90 (23) disables the

manual limit stops until

preset 91 (24) is set.

1. Make sure limit stops are turned ON (refer to the Limit Stops section), then exit the menu.

2. Push the joystick left until you reach the limit you want the camera to go to on the left.

3. Program preset 90 (23).

4. Push the stick right to the limit you want the camera to go to on the right.

5. Program preset 91 (24).

Setting presets 90 (23) and 91 (24) to the same point disables manual limit stops.

SCAN LIMIT STOPS

Refer to the documentation for your control system for programming presets, then do the

following:

NOTE: On power-up, the

auto scan tilt angle will be

whatever angle the camera

was at when the right scan

limit was set.

1. Make sure limit stops are turned ON (refer to the Limit Stops section), then exit the menu.

2. Push the joystick left until you reach the limit you want the camera to go to on the left.

3. Program preset 92 (25).

4. Push the joystick right to the limit you want the camera to go to on the right.

5. Program preset 93 (26).

Setting presets 92 (25) and 93 (26) to the same point disables scan limit stops.

PARK TIME MINUTES

This feature parks the dome at preset 1 after a programmed number of minutes of control

inactivity.You can set the time from 1 to 720 minutes (12 hours). Setting the time to zero

disables this feature. To change the park time:

NOTE: Preset 1 must be

programmed for the dome to

park.

1. On the main menu, move the joystick up or down to position the cursor (>) beside Other.

2. Press the Iris Open button to enter the Other submenu.

3. Move the joystick up or down to position the cursor beside Park Time Minutes.

4. Press the Iris Open button. The cursor moves to the right beside the current park time.

5. Move the joystick up or down to change the park time.

6. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

SCAN SPEED

Scan speed is adjustable from 1-40 degrees per second, and occurs in three scan modes:

auto, random, and frame. To change the scan speed:

1. On the main menu, move the joystick up or down to position the cursor (>) beside Other.

2. Press the Iris Open button to enter the Other submenu.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Move the joystick up or down to position the cursor beside Scan Speed deg/s.

4. Press the Iris Open button. The cursor moves to the right beside the current number of

degrees.

5. Move the joystick up or down to toggle through the number of degrees (1-40) until you

reach the number you want. (If set on a low number, the scan will appear to barely

move but is still functioning.)

6. SELECT – Press the Iris Open button to select your choice.

CANCEL – Press the Iris Close button if you do not want to change the setting.

TROUBLESHOOTING

NOTE: The dome drive con-

tains no user-serviceable

parts. If there is a problem

with the dome drive, return it

to Pelco as a complete unit

for servicing.

Symptom: Unit or fan does not operate.

1. Make sure your controller is trying to communicate with the unit and not another camera.

2. Turn off power.

3. Remove the lower dome:

In-Ceiling Models – Insert the flat blade of a screwdriver into one of the slots on

the trim ring and twist the screwdriver to pop loose the trim ring and lower dome.

Pendant Models – Remove the two screws that hold the trim ring to the back box.

Insert the flat blade of a screwdriver into one of the slots on the trim ring and twist the

screwdriver to free the lower dome from the back box.

4. Remove the dome drive: Push in on the green drive eject tab on the side of the dome

drive and gently rock the dome drive to release the latch. When the green latch

releases, pull the dome down.

5. Do one of the following:

•

If your problem was that the unit would not operate: Proceed to step 6.

If your problem was that the fan would not operate: Make sure the connector for

the fan is fully seated. Replace the dome drive. Turn on power. If the fan does not

operate, return the back box electronic assembly and dome drive to the factory

for repair. Refer to the Back Box Electronic Assembly Removal section.

6. Turn on power.

7. If the red power LED on the door of the interconnect circuit board in the back box does

not light, turn off power.

a. Open the door to the interconnect circuit board and check the fuse (located next

to the fan). If bad, replace it (Pelco part number FUS1.6-5X20FAST). This is a

1.6-ampere fuse, 5 x 20 mm, fast blow.

b. If the fuse is good, turn on power and use a voltmeter to check if 24 VAC is getting

to the power connector on the interconnect circuit board (located next to the fuse).

c. If there is 24 VAC to the power connector, turn off power and return the back box

electronic assembly to the factory for repair. Refer to the Back Box Electronic

Assembly Removal section.

d. If there is no voltage at the power connector, check your power supply.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

8. If the red power LED is lit, turn off power.

a. Open the door to the interconnect circuit board and check that all connectors are

fully seated.

b. Make sure the wiring is correct between the unit and controller.

c. Close the door. Check the switch settings on the dome drive (refer to Tables A, B,

and C) and reinstall the dome drive.

d. Turn on power. If the unit still does not operate, turn off power and replace the

dome drive with a unit that is good, if you have a spare. Check the switch settings

on the substitute dome drive before installing it. If you do not have a spare, return

the dome drive to the factory. Also return the back box electronic assembly. Refer

to the Back Box Electronic Assembly Removal section.

e. If you substituted a dome drive, turn on power. If the unit operates, the original

dome drive is bad. Return it to the factory. If the unit still does not operate, then

the interconnect board is bad. Return the back box electronic assembly to the

factory. Refer to the Back Box Electronic Assembly Removal section.

BACK BOX ELECTRONIC ASSEMBLY REMOVAL

1. Turn off power.

2. Open the interconnect door and disconnect all wiring to the back box.

3. Use an 11/32 socket driver to remove the three 8-32 washers and nuts that hold the

electronic assembly to the back box. When you remove the screws the interconnect

back box receptacle will drop down. You may have to move the open interconnect

door past 90 degrees vertical toward the side of the back box to release the door from

the built-in grounding strip (and free the interconnect back box receptacle).

4. Remove the interconnect back box receptacle with the electronic components from the

back box.

SPECIFICATIONS

MECHANICAL

Pan Movement:

Vertical Tilt:

360° continuous pan rotation

Unobstructed +2° to -92°

Manual Pan Speed:

Manual Tilt Speed:

Preset Speeds:

0.5°-80°/sec manual operation, 150°/sec turbo

0.5°-40°/sec

Pan

Tilt

250°/sec

200°/sec

30°/sec

12°/sec

Fixed-Speed Controller: Pan

Tilt

CAMERA

Signal Format:

NTSC (Spectra Lite™ model DD5TAC)

PAL (Spectra Lite™ model DD5TAC-X)

2:1 interlace

Scanning System:

Image Sensor:

1/4-inch interline transfer

Effective Pixels:

NTSC 510 (H) x 492 (V)

PAL

500 (H) x 582 (V)

Resolution:

NTSC 350 TV lines

PAL

350 TV lines

Lens

Minimum f-stop:

Focal Length:

Zoom Ratio:

Horizontal Angle

of View:

F/1.6

3.9 mm to 63 mm optical

16X optical zoom

44° (at 3.9 mm wide zoom), 3° (at 63 mm telephoto zoom)

>1 million cycles at room temperature (zoom, focus, iris)

Automatic with manual override and preset capability

MTBF:

Focus:

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Sensitivity:

1 lux at f1.6 at signal level of 40 IRE, gain high (AGC on)

DSP-3R

AC line lock

Automatic with manual override*

Automatic (electronic iris)/manual

NTSC 1/60 – 1/10,000*

Signal Process:

Sync System:

White Balance:

Shutter Speed:

PAL 1/50 – 1/10,000*

Iris Control:

Automatic with manual override*

.714 V ±.07 V (100 IRE ±10 IRE)

>46 dB

Gain Control:

Video Output:

Signal to Noise:

* Manual control over camera setup functions depends on the head end and is not

available on all control models.

(Design and product specifications subject to change without notice.)

REGULATORY NOTICES

This equipment has been tested and found to comply with the limits of a Class A digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a commer-

cial environment. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

WARRANTY AND RETURN INFORMATION

WARRANTY

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100

or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide

the following information:

Pelco will repair or replace, without charge, any merchandise proved defective

in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Three years on Genex™ Series (multiplexers, server, and keyboard).

Two years on all standard motorized and fixed focal length lenses.

Two years on Esprit™, Legacy^®, Intercept^®, PV1000 Series, CM6700/

CM8500/CM9500/CM9750/CM9760 Matrix, Spectra^®, DF5 Series and DF8

Fixed Dome products.

Two years on WW5700 series window wiper (excluding wiper blades).

Two years on cameras.

Six months on all pan and tilts, scanners or preset lenses used in continu-

ous motion applications (that is, preset scan, tour and auto scan modes).

If there is a dispute regarding the warranty of a product which does not fall

under the warranty conditions stated above, please include a written explana-

tion with the product when returned.

•

Ship freight prepaid to:

Pelco

300 West Pontiac Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid

to Pelco, Clovis, California. Repairs made necessary by reason of misuse, al-

teration, normal wear, or accident are not covered under this warranty.

Method of return shipment shall be the same or equal to the method by which

the item was received by Pelco.

RETURNS

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence, infringe-

ment of any rights of any party or product liability, relating to the Products shall

not exceed the price paid by the Dealer to Pelco for such Products. In no event

will Pelco be liable for any special, incidental or consequential damages (includ-

ing loss of use, loss of profit and claims of third parties) however caused, whether

by the negligence of Pelco or otherwise.

In order to expedite parts returned to the factory for repair or credit, please call

the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num-

ber (CA number if returned for credit, and RA number if returned for repair).

Goods returned for repair or credit should be clearly identified with the assigned

CA/RA number and freight should be prepaid. All merchandise returned for credit

may be subject to a 20% restocking and refurbishing charge.

Ship freight prepaid to:

Pelco

The above warranty provides the Dealer with specific legal rights. The Dealer

may also have additional rights, which are subject to variation from state to state.

300 West Pontiac Way

Clovis, CA 93612-5699

REVISION HISTORY

Manual #

C1498M

Date

2/99

3/99

7/99

Comments

Original version.

Removed reference to line synchronization. Added material on auto iris. Added FCC notice.

Revised the preset tilt speed from 100 to 200 degrees/second. Added model number and specifications for a PAL camera.

Revised Troubleshooting section. Revised manual to new format.

Changed camera zoom from 12X to 16X. Added line sync and auto focus features. Removed auto iris peak and auto sharpness

options. Replaced R-B and M-G white balance options with white balance hue option. Revised camera specifications.

C1498M-A

C1498M-B

7/99

® Pelco and the Pelco logo are registered trademarks of Pelco.

Pelco Manual C1498M-B (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Pentair Water System UV 110 User Manual
Philips Cell Phone CT0392BLK User Manual
Philips Flat Panel Television 19PFL3403D 10 User Manual
Philips Speaker System MC 220 User Manual
Philips TV Cables SWV7513W User Manual
Philips VCR VRZ255AT User Manual
Porter Cable MP3 Player SA4005 User Manual
PQI Computer Drive I Stick 20 User Manual
ProForm Home Gym PFEL079070 User Manual
Proxima ASA Projector DP9270 User Manual