Pelco Security Camera AV2100 User Manual

Release Notes  
Arecont Vision IP Cameras Supported on Digital Sentry  
Integral Digital Sentry® digital video management systems (DVMS) support certain  
Arecont Vision IP camera models. The camera models listed in this document can be  
used with Digital Sentry IP camera driver version 6.8.0.126 and later. Refer to each  
camera’s table for information about the hardware and software features validated for  
use on a Digital Sentry system. Any general limitations or special instructions are listed  
at the beginning of the document, and any model-specific information is listed after each  
table. For information about the general usage of each camera, refer to the camera  
manufacturer’s documentation.  
To obtain the latest IP camera driver or documentation for use with Digital Sentry, refer  
to the Pelco Web site at www.pelco.com.  
General Arecont Vision IP Camera Notes  
• Frame rates are rounded down to the next valid value listed in the tables. For  
example, if the requested frame rate is 7.5 frames per second (fps), the camera  
provides 7 fps.  
• The frame rate requested might not match specifications in the camera  
manufacturer’s documentation.  
• Camera resolutions configured in DSAdmin must match resolutions supported in this  
document.  
• Always stop the Digital Sentry VideoServer service before running the Arecont Vision  
AV Manager application. After AV Manager configuration is complete, change the AV  
Manager server startup type to Disabled (LMSrv), and then restart the VideoServer  
service.  
• Digital Sentry cannot function properly while any Arecont Vision application is active  
on the same system. Check the system tray to verify that Arecont Vision applications  
are not active.  
• Using Integral motion detection decreases Digital Sentry performance because of  
increased CPU usage, especially at higher resolutions. It is recommended that  
In-Camera motion detection be used at higher resolutions.  
• Frame rates could be reduced as resolution and quality settings are increased.  
• Arecont Vision cameras cannot be dual-homed. That is, they cannot be streamed to  
two Digital Sentry systems or applications simultaneously.  
To provide a stable camera environment, make sure local or Power over Ethernet  
(PoE) power meets or exceeds the requirement of the camera used.  
C1001RN (9/08)  
Page 1 of 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Arecont Vision AV3100  
Firmware  
62414  
Supported Resolutions  
FPS  
1920 x 1200, 960 x 600  
1–22  
20  
Number of Quality Settings  
Supported Codec  
MJPEG  
Supported Motion Detection Integral, In-Camera  
Pan/Tilt/Zoom (PTZ)  
Not available  
NOTES:  
To capture images larger than 2 MP, you must install Integral IP camera driver 6.7.0.5  
or later and then Megapixel Support for DS Server/VAU 4.1. To obtain a copy of all  
necessary software versions, go to www.pelco.com.  
To view images larger than 2 MP, you must install Megapixel Support for DS Client/  
Admin 4.1 and DS ControlPoint 6.5.1.28 or later. To obtain a copy of all necessary  
software versions, go to www.pelco.com.  
• Short communication delays (2–3 minutes) could occur when you use Digital Sentry  
to change the configuration of AV3100. The number and frequency of delays can be  
decreased by combining multiple configuration changes into as few groups as  
possible.  
• In-camera motion detection on AV3100 is less sensitive at lower resolutions. It is  
recommended that Integral motion detection be used at lower resolutions with this  
camera.  
C1001RN (9/08)  
Page 3 of 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Arecont Vision AV3130  
Firmware  
62315  
Supported Resolutions  
Day mode:  
1920 x 1200, 960 x 600  
Night/Automatic mode:  
1280 x 1024, 640 x 512  
FPS  
1–20  
21  
Number of Quality Settings  
Supported Codec  
MJPEG  
Supported Motion Detection Integral  
Pan/Tilt/Zoom (PTZ)  
Not available  
NOTES:  
To capture images larger than 2 MP, you must install Integral IP camera driver 6.7.0.5  
or later and then Megapixel Support for DS Server/VAU 4.1. To obtain a copy of all  
necessary software versions, go to www.pelco.com.  
To view images larger than 2 MP, you must install Megapixel Support for DS Client/  
Admin 4.1 and DS ControlPoint 6.5.1.28 or later. To obtain a copy of all necessary  
software versions, go to www.pelco.com.  
• Short communication delays (2–3 minutes) could occur when you use Digital Sentry  
to change the configuration of AV3130. The number and frequency of delays can be  
decreased by combining multiple configuration changes into as few groups as  
possible.  
• When configuring AV3130 in DSAdmin, three different drivers are available including  
one each for Day, Night, and Automatic modes. The selected driver must match the  
mode selected in the camera’s software.  
Page 4 of 6  
C1001RN (9/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Arecont Vision AV5100  
Firmware  
62406  
Supported Resolutions  
FPS  
2560 x 1920, 1280 x 960  
1–16  
20  
Number of Quality Settings  
Supported Codec  
MJPEG  
Supported Motion Detection Integral  
Pan/Tilt/Zoom (PTZ)  
Not available  
NOTES:  
To capture images larger than 2 MP, you must install Integral IP camera driver 6.7.0.5  
or later and then Megapixel Support for DS Server/VAU 4.1. To obtain a copy of all  
necessary software versions, go to www.pelco.com.  
To view images larger than 2 MP, you must install Megapixel Support for DS Client/  
Admin 4.1 and DS ControlPoint 6.5.1.28 or later. To obtain a copy of all necessary  
software versions, go to www.pelco.com.  
• Short communication delays (2–3 minutes) could occur when you use Digital Sentry  
to change the configuration of AV5100. The number and frequency of delays can be  
decreased by combining multiple configuration changes into as few groups as  
possible.  
• In-camera motion detection will be supported on AV5100 in a later release.  
C1001RN (9/08)  
Page 5 of 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Arecont Vision AV8180 and AV8360  
Firmware  
62410  
Supported Resolutions  
1600 x 1200, 800 x 600  
(per sensor) x4  
FPS  
1–22  
20  
Number of Quality Settings  
Supported Codec  
MJPEG  
Supported Motion Detection Integral  
Pan/Tilt/Zoom (PTZ)  
Not available  
NOTES:  
• The frame rate and quality for all four camera sensors (heads) must be set to the  
same value.  
• AV8180 and AV8360 do not have a configuration Web page.  
• AV8180 and AV8360 do not support in-camera motion detection. Using Integral  
motion detection at 1600 x 1200 resolution can significantly reduce the performance  
of the Digital Sentry system. To use Integral motion detection, it is recommended  
that you select 800 x 600 resolution.  
• AV8180 camera input numbers are not in the same order as their physical locations  
on the camera.  
Contact Information  
Pelco Worldwide Headquarters  
3500 Pelco Way, Clovis, California 93612 USA  
USA & Canada: Tel: (800) 289-9100, Fax: (800) 289-9150  
International: Tel: +1(559) 292-1981, Fax: +1(559) 348-1120  
Document Revision History  
Document #  
Date  
Comments  
C1001RN  
9/08  
Original version.  
Pelco, the Pelco logo, and Digital Sentry are registered trademarks of Pelco, Inc.  
© Copyright 2008, Pelco, Inc. All rights reserved.  
Page 6 of 6  
C1001RN (9/08)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Perreaux Stereo Amplifier Model II User Manual
Philips CRT Television XS1956CI User Manual
Philips Headphones SBC HL300U User Manual
Philips Headphones SHE2637 User Manual
Philips Indoor Furnishings QBS050 5 User Manual
Philips Speaker System A3310 User Manual
Philips TV Receiver 42PF9641D 10 User Manual
Pioneer DJ Equipment SEP C1 User Manual
Premier Mounts TV Mount INW 42 User Manual
Profoto Indoor Furnishings AcuteB Head User Manual