Pelco Home Security System C1487M H User Manual

SD5 Series

Spectra II™ and

Spectra Lite™

Dome Systems

Installation Manual

C1487M-H (1/01)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150

International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Section

Page

IMPORTANT SAFEGUARDS AND WARNINGS.................................................................................................................... 4

INSTALLATION .......................................................................................................................................................................5

HARD CEILING INSTALLATION.................................................................................................................................... 6

SUSPENDED CEILING INSTALLATION ....................................................................................................................... 8

PENDANT-MOUNT INSTALLATION ............................................................................................................................. 10

SURFACE-MOUNT INSTALLATION ............................................................................................................................. 12

TROUBLESHOOTING ...........................................................................................................................................................14

APPENDIX .............................................................................................................................................................................15

SPECIFICATIONS .................................................................................................................................................................19

CERTIFICATIONS AND REGULATORY NOTICES .......................................................................................................23

WARRANTY AND RETURN INFORMATION ........................................................................................................................24

LIST OF ILLUSTRATIONS

Figure

Page

SD5 Series Dimension Drawing ............................................................................................................................20

LIST OF TABLES

Table

Page

Video Coaxial Cable Wiring Distances ..................................................................................................................15

24 VAC Wiring Distances .......................................................................................................................................15

Switch Settings for SW1 ........................................................................................................................................15

Switch Settings for SW2 – P-Type Control ............................................................................................................16

Switch Settings for SW2 – D-Type Control ............................................................................................................16

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it

must not be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to

verify the exposed parts have not been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and

lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage

constituting a risk of electric shock is present within

this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

This symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying this unit.

DO NOT OPEN.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

MEASURES DE SECURITE IMPORTANTES

Avant d’installer ou d’utiliser ce produit, les mesures de sécurité suivantes sont à prendre:

1. Toute installation et réparation devraient être entreprises par un technicien qualifié et conformes au codes locaux.

2. A moins que cet equipement indique avoir un boitié agrée NEMA de type 3, 3R, 3S, 4, 4X, 6 ou 6P, il est uniquement conçu pour

utilisation intérieure et ne peut donc pas être en contact de pluie ou d’humidité.

3. Utiliser seulement les pièces de rechanges recommandées par Pelco.

4. Après toute installation ou réparation de la partie électrique de ce produit, une résistance entre le courant et la partie exposée devrait

être installée afin de vérifier que la partie électrique n’aie pas été en contact d’un court circuit.

5. L’installation entreprise et le matériel utilisé devraient supporter quatre fois le poids du boitié, de la tourelle, de la caméra, et de la

lentille.

Ce produit et/ou le manuel pourrait inclurent les symbols suivants:

Ce symbol indique qu’un voltage dangereux

pouvant provoquer un chock électrique est

présant dans cette unité.

CAUTION:

RISQUE DE CHOQUE ÉLECTRIQUE.

NE PAS OUVRIR.

Ce symbol indique qu’il y a des mesures

d’installation et d’entretient importantes

inclus dans le manuel de cet équipement.

Nous vous prions de bien vous familiarisez avec la manuel avant d’entreprendre toute installation.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes. Inspect each box to make sure all parts are

present.

IN-CEILING MODELS

Back Box

PENDANT MODELS

Back Box

Back box

Parts bag

Back box

Tube of thread compound

Conduit fitting

Dome Drive

Safety chain bracket

Lock nut

Compass tool

T-rail clip (clip, L-bracket, screw, lock washer and nut)

Dome drive

Lower Dome

Acrylic lower dome with trim ring

Parts bag (O-ring and lubricant, and tube of Loctite)

Dome Drive

Dome drive

Lower Dome

Acrylic lower dome with trim ring

BACK BOX

DOME DRIVE

LOWER DOME

COMPASS TOOL

SAFETY BRACKET

T-RAIL CLIP

CONDUIT FITTING & LOCK NUT

THREAD LOCTITE®

COMPOUND 222MS

O-RING

LUBE

O-RING

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

HARD CEILING INSTALLATION

IN-CEILING MODELS

STEP 1 - PREPARE CEILING

a. Locate the center point of the mounting location. Drill a hole in

the ceiling using a 3/32-inch drill. Insert the compass tool into

the hole.

b. Draw a circle on the ceiling using the compass tool and a

pencil. Cut the circle out of the ceiling.

STEP 2 - INSTALL THE BACK BOX

ATTACH SAFETY CHAIN HERE

a. Attach the conduit fitting, lock nut, and safety chain bracket.

Install a safety chain/cable (not supplied) that will support up

to 16 pounds (7.3 kg).

b. Turn the thumb screw and open the hinged door to the back

box. Pull wiring into the back box through the conduit fitting.

Refer to Tables A and B in the Appendix for wiring distances.

CEILING TILE

c. Compress the spring clips on the back box and push it through

the hole, until the clips spring back. Tighten the screws until

you hear a clicking noise.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

CONTROLLER

VIDEO IN

d. Attach the wiring to the circuit board inside the back box. When

finished, close the door to the back box and turn on the power.

The red LED will light.

COAXITRON

VIDEO OUT

CONTROLLER

TX-

TX+

RX-

RX+

TX-

TX+

2 WIRE

CONTROLLER

CONTROL

(RS-422)

NOT USED

IMPORTANT: If the LED does not light, refer to the Trouble-

shooting section.

ALARM

INPUTS

SPECTRA II ONLY

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

GROUND

SWITCHES

(WIRING EXAMPLE)

+5 to +24 VDC

+5 VDC

(NO)

RELAY

(AUX 1)

(NC)

GROUND

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

HEATER/FAN

(NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

STEP 3 - INSTALL DOME DRIVE

SW1

SW2

LABEL

SW1

RED

TAB

SW2

GREEN

TAB

LABEL

SW2

RS-422 TERMINATION SWITCH

00303

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the

labels on the dome drive or Tables C through E in the Appen-

dix in the back of this manual.

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the

last unit in the chain (farthest from the controller). To terminate

the dome drive set the RS-422 termination switch to the left.

STEP 4 - INSTALL LOWER DOME

a. Snap the clip, on the end of the trim ring leash, into the hole on the

lip of the back box.

b. Line up the snaps on the trim ring with the mounting screws on the

back box. Snap the trim ring into the plastic snap washers on the

mounting screws.

TO USE YOUR DOME, REFER TO THE

OPERATION AND PROGRAMMING MANUAL.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SUSPENDED CEILING INSTALLATION

IN-CEILING MODELS

STEP 1 - PREPARE CEILING TILE

NOTE: The ceiling tile cannot be thinner than 0.50-inch (1.27 cm) or thicker than 1.75-inches (4.45 cm).

a. Remove the ceiling tile from the ceiling. Insert the compass tool (supplied) into the center of the tile. (If necessary use a 3/32-inch bit

to drill a hole.)

b. Draw a circle on the tile using the compass tool and a pencil. Cut the circle out of the ceiling tile.

STEP 2 - INSTALL THE BACK BOX

ATTACH SAFETY CHAIN HERE

a. Attach the conduit fitting, lock nut, and safety chain bracket.

Install a safety chain/cable (not supplied) that will support up

to 16 pounds (7.3 kg).

b. Turn the thumb screw and open the hinged door to the back

box. Pull wiring into the back box through the conduit fitting.

Refer to Tables A and B in the Appendix for wiring distances.

CEILING TILE

T-RAIL CLIP

FOR

CEILING TILE

T-RAIL CLIP

FOR

CEILING TILE

c. Compress the spring clips on the back box and push it through

the hole, until the clips spring back. Tighten the screws until

you hear a clicking noise.

d. Install the ceiling tile with the back box. Attach a T-rail clip on

each side of the ceiling tile. Fasten the L-bracket to the clip

with the supplied screw and washers.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

24 VAC

POWER

e. Attach the wiring to the circuit board inside the back box. When

finished, close the door to the back box and turn on the power.

The red LED will light.

TRANFORMER

(24 VAC ONLY)

CONTROLLER

VIDEO IN

COAXITRON

CONTROLLER

VIDEO OUT

TX-

TX+

RX-

RX+

TX-

TX+

IMPORTANT: If the LED does not light, refer to the Trouble-

shooting section.

2 WIRE

CONTROLLER

CONTROL

(RS-422)

NOT USED

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

ALARM

INPUTS

SPECTRA II ONLY

GROUND

SWITCHES

(WIRING EXAMPLE)

+5 to +24 VDC

+5 VDC

(NO)

RELAY

(AUX 1)

(NC)

GROUND

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

HEATER/FAN

(NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

STEP 3 - INSTALL DOME DRIVE

SW1

SW2

LABEL

SW1

RED

TAB

SW2

GREEN

TAB

LABEL

SW2

RS-422 TERMINATION SWITCH

00303

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the

labels on the dome drive or Tables C through E in the Appen-

dix in the back of this manual.

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the

last unit in the chain (farthest from the controller). To terminate

the dome drive set the RS-422 termination switch to the left.

STEP 4 - INSTALL LOWER DOME

a. Snap the clip, on the end of the trim ring leash, into the hole on the

lip of the back box.

b. Line up the snaps on the trim ring with the mounting screws on the

back box. Snap the trim ring into the plastic snap washers on the

mounting screws.

TO USE YOUR DOME, REFER TO THE

OPERATION AND PROGRAMMING MANUAL.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

PENDANT-MOUNT INSTALLATION

PENDANT MODELS

STEP 1 - MOUNT AND INSTALL THE BACK BOX

NOTE: If installing outdoors make sure the installation is properly sealed to keep moisture out.

a. Install the mount for the pendant dome. Refer to the instruc-

tions supplied with the mount. Bring the wiring for the dome

through the mount. Refer to Tables A and B in theAppendix for

wiring distances.

b. Turn the thumbscrew and open the hinged door located inside

the back box.

c. Pull wiring from the mount into the back box.

d. Screw the back box into the mount. If outdoors, apply thread

compound (provided) to the threads on the back box.

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

STEP 2 - WIRE CIRCUIT BOARD

CONTROLLER

VIDEO IN

COAXITRON

Attach the wiring to the interconnect circuit board inside the back

box. Close the door to the back box. Turn on power to the back

box. The red LED will light.

VIDEO OUT

CONTROLLER

TX-

TX+

RX-

RX+

TX-

2 WIRE

CONTROLLER

CONTROL

(RS-422)

NOT USED

TX+

IMPORTANT: If the LED does not light, refer to the Trouble-

shooting section.

ALARM

INPUTS

SPECTRA II ONLY

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

GROUND

SWITCHES

(WIRING EXAMPLE)

+5 to +24 VDC

+5 VDC

(NO)

RELAY

(AUX 1)

(NC)

GROUND

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

HEATER/FAN

(NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 3 - INSTALL DOME DRIVE

SW1

SW2

LABEL

SW1

RED

TAB

SW2

GREEN

TAB

LABEL

SW2

RS-422 TERMINATION SWITCH

00303

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the

labels on the dome drive or tables C through E in theAppendix

in the back of this manual.

last unit in the chain (farthest from the controller). To terminate

the dome drive set the RS-422 termination switch to the left.

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the

STEP 4 - INSTALL LOWER DOME

LEASH

ATTACH

LEASH TO

NEAREST

RETAINER

SCREW

MOUNTING

SCREW HOLES

FRONT & BACK

b. Attach the back box trim leash to the lower dome. Use retainer

screw (nearest to a mounting screw) inside lower dome.

a. Lightly apply O-ring lubricant to the O-ring. Install the O-ring in

the groove on the trim ring of the lower dome.

NOTE: If you are install-

ing an outdoor model,

plug the two-pin heater

connection in the lower

dome into the mating

connector in the back

box.

c. Remove the two lower dome, mounting screws. Apply a drop

of Loctite 222MS (supplied) to each screw.

d. Push the lower dome inside the back box, line up the mounting

screw holes, and install the two mounting screws.

TO USE YOUR DOME, REFER TO THE OPERATION AND PROGRAMMING MANUAL.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SURFACE-MOUNT INSTALLATION

PENDANT MODELS

STEP 1 - REMOVE THE TOP PORTION OF THE BACK BOX

a. Turn the thumbscrew and open the

hinged door located inside the back box.

b. Unscrew the three Phillips screws lo-

cated underneath the hinged door.

c. Remove the top portion of the back box.

STEP 2 - PREPARE SURFACE AND INSTALL THE BACK BOX

NOTE: If installing outdoors

apply a sealant between the

back box and the mounting

surface

a. Determine the mounting location. Use the base of the back box as a template. Mark the fastener and center hole positions onto the

mounting surface.

b. Drill a hole in the center of the mounting surface. Pull wiring through the opening. Refer to Tables A and B in the Appendix for wiring

distances. Prepare the holes for the fasteners. Position the back box over the mounting holes and pull wiring into the back box.

Secure the back box to the mounting surface using the appropriate hardware for your installation.

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

CONTROLLER

VIDEO IN

STEP 3 - WIRE CIRCUIT BOARD

COAXITRON

CONTROLLER

VIDEO OUT

Attach the wiring to the interconnect circuit board inside the back

box. Close the door to the back box. Turn on power to the back

box. The red LED will light.

TX-

TX+

RX-

RX+

TX-

TX+

2 WIRE

CONTROLLER

CONTROL

(RS-422)

NOT USED

IMPORTANT: If the LED does not light, refer to the Trouble-

ALARM

INPUTS

SPECTRA II ONLY

shooting section.

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

GROUND

SWITCHES

(WIRING EXAMPLE)

+5 to +24 VDC

+5 VDC

(NO)

RELAY

(AUX 1)

(NC)

GROUND

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

HEATER/FAN

(NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 4 - INSTALL DOME DRIVE

SW1

SW2

LABEL

SW1

RED

TAB

SW2

GREEN

TAB

LABEL

SW2

RS-422 TERMINATION SWITCH

00303

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the

labels on the dome drive or Tables C through E in the Appen-

dix in the back of this manual.

last unit in the chain (farthest from the controller). To terminate

the dome drive set the RS-422 termination switch to the left.

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the

STEP 5 - INSTALL LOWER DOME

LEASH

ATTACH

LEASH TO

NEAREST

RETAINER

SCREW

MOUNTING

SCREW HOLES

FRONT & BACK

a. Lightly apply O-ring lubricant to the O-ring. Install the O-ring in

the groove on the trim ring of the lower dome.

b. Attach the back box trim leash to the lower dome. Use the

retainer screw (nearest to a mounting screw) inside lower dome.

NOTE: If you are install-

ing an outdoor model,

plug the two-pin heater

connection in the lower

dome into the mating

connector in the back

box.

c. Remove the two lower dome, mounting screws. Apply a drop

of Loctite (supplied) to each screw.

d. Push the lower dome inside the back box, line up the mounting

screw holes, and install the two mounting screws.

TO USE YOUR DOME, REFER TO THE OPERATION AND PROGRAMMING MANUAL.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Unit does not operate.

The controller is not

communicating with the

Spectra unit.

Check to see if the red LED on the circuit

board in the back box is lit.

1. The red LED is not lit.

a. Fuse is bad.

a. Check fuse on the circuit board. Replace fuse if

it is bad. To order a fuse from Pelco, specify the

part number FUS1.6-5X20FAST. This is a 1.6-

ampere fuse, 5 x 20 mm, fast blow.

b. 24 VAC power source is not con-

nected or back box is bad.

b. Use a voltmeter to check if 24 VAC is getting to

the power connector on the circuit board. If NO,

check your power supply. If YES, return the back

box to the factory for repair.

2. The red LED is lit.

a. Wiring is incorrect or is not fully

seated.

a. Check all connections to the circuit board.

Make sure that all connections are fully seated

and the board is wired correctly.

b. DIP switch settings are incorrect.

b. Check the DIP switch settings on the dome

drive (refer to Tables C, D, and E). If the unit still

does not operate, turn off power and replace

the dome drive with a good unit, if you have a

spare. Check the switch settings on the substi-

tute dome drive before installing it. (If you do not

have a spare, return the dome drive and back

box to the factory.) If you substituted a dome

drive and the unit operates, the original

dome drive is bad (return the dome drive to the

factory). If the unit still does not operate,

then the circuit board is bad (return the back

box to the factory).

Fan does not operate.

Fan connections are not fully seated.

Cameras are out of phase.

Make sure the connector for the fan is fully seated.

If the fan still does not operate, return the back box

and dome drive to the factory for repair.

Vertical roll on monitor

when switching between

cameras.

If you are wiring more than one dome to the same

transformer, it is important to wire the power con-

nector in each dome the same way. That is, the

wiring from one side of the transformer must be

connected to the same connector on each dome.

DOME 1

POWER

WARNING: Make

sure you wire power

to the outer connec-

tors of the terminal

block and ground to

the middle connec-

DOME 2

POWER

tor. Otherwise, you

could damage the

DOME 3

POWER

dome.

Pelco Installation Manual C1487M-H (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Table A. Video Coaxial Cable Wiring Distances

Cable Type*

Maximum Distance

RG59/U

RG6/U

RG11/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance. All-copper center conductor.

95% braided copper shield.

Table B. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC with a 10-

percent voltage drop. (Ten percent is generally the maximum allowable voltage

drop for AC-powered devices.)

Wire Gauge

30 vA

75 vA

94 ft

(28 m)

150 ft

(45 m

238 ft

(115 m)

380 ft

(72 m)

603 ft

(183 m)

960 ft

(292 m)

37 ft

60 ft

95 ft

152 ft

241 ft

384 ft

(11 m)

(18 m)

(29 m)

(46 m)

(73 m)

(117 m)

NOTE: Input power for the dome is 24 VAC only. Power consumption is 30 vA per

dome for indoor models and 75 vA for outdoor models.

Use a 24 VAC transformer with the following minimum vA:

40 vA per dome

100 vA per dome

For indoor models (without heater)

For outdoor models (with heater)

Table C. Switch Settings for SW1

Control Type

Switch Setting

SW1-4

OFF

SW1-1

OFF

SW1-2

OFF

SW1-3

OFF

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

OFF**

Coaxitron^®

P-Type Control

D-Type Control

OFF

OFF*

NOTES: Switches SW 1-3 through SW 1-6 MUST be OFF.

D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500, CM8500, and Genex^®controllers or with

American Dynamics control systems using the AD2083 Translator.

P-type control is RS-422 that is compatible with Pelco’s CM6700/CM9750/CM9760 and Genexcontrol systems.

* OFF- Use with controllers that have more than 32 presets.

ON- Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

For CM9502 with fixed speed keyboards, set switch OFF.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

Pelco Installation Manual C1487M-H (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table D. Switch Settings for SW2 – P-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For D-type control systems, refer to Table E.

Receiver

Address

Switch Setting

SW2-3

Receiver

Address

Switch Setting

SW2-3

SW2-1

SW2-2

SW2-4

SW2-5

SW2-1

SW2-2

SW2-4

SW2-5

OFF

Baud Rate

Switch Setting

SW2-6

SW2-7

SW2-8

2400

4800

9600

OFF

Table E. Switch Settings for SW2 – D-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For P-type control systems, refer to Table D.

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

(Continued on next page)

Pelco Installation Manual C1487M-H (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

OFF

100

101

102

103

104

OFF

(Continued on next page)

Pelco Installation Manual C1487M-H (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

OFF

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

MECHANICAL

Construction

Back box:

Aluminum

Dome drive:

Lower dome:

Aluminum, ABS plastic

Acrylic

Cable Entry

In-Ceiling:

Pendant:

.75-inch (1.91 cm) conduit fitting

Through 1.5-inch (3.81 cm) NPT pendant mount

Pan Movement:

Vertical Tilt:

360° continuous pan rotation

Unobstructed +2° to -92°

Manual Pan/Tilt Speeds*

Pan

Spectra II:

Spectra Lite:

Tilt

0.1°-80°/sec manual operation, 150°/sec turbo

0.5°-80°/sec manual operation, 150°/sec turbo

Spectra II:

Spectra Lite:

0.1°-40°/sec

0.5°-40°/sec

Preset Speeds

Pan:

Tilt:

250°/sec

200°/sec

* For variable-speed operation an appropriate controller is required. With fixed-speed controllers, Spectra II and Spectra Lite pan/tilt

speed is 24°/sec. The CM6700 controller with the KBD200 keyboard has programmable fixed speeds.

ELECTRICAL

Input Voltage:

18-30 VAC, 24 VAC nominal

Input Power

In-ceiling:

30 vA

75 vA

Indoor pendant:

Outdoor pendant:

Fuse: 1.6 A

Relay Contacts

Type:

AUX 1

Form C

Low voltage (<40 V)

2 A maximum

AUX 2 Output

Open collector transistor output

32 VDC maximum

Voltage:

Current:

150 mA maximum

GENERAL

Environment

In-Ceiling:

Pendant:

Indoor only

Indoor/outdoor

Operating Range

In-Ceiling:

32° to 140°F (0° to 60°C) intermittent operation; 32° to 122°F (0° to 50°C) continuous operation

Pendant

Without Heater:

32° to 140°F (0° to 60°C) absolute maximum operating temperature; 32° to 122°F (0° to 50°C) sustained

maximum operating temperature

With Heater:

(Assumes no wind chill factor; for detailed test conditions, contact Pelco.)

Maximum operating temperature: 140°F (60°C) absolute maximum; 122°F (50°C) sustained maximum

Minimum operating temperature: -60°F (-51.11°C) absolute minimum; minimal icing at -50°F (-45.56°C)

sustained minimum; prevents icing at -40°F (-40°C) sustained minimum; de-ices .1 inch (2.5 mm) within 3

hours after power-up

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions:

Ratings:

See Figure 1

NEMA Type 1–In-ceiling back boxes, all dome drives

NEMA Type 4X–Pendant back boxes

IP 66–Pendant back boxes

Weight

Unit

Shipping

In-Ceiling

Back Box:

Dome Drive:

Lower Dome:

Pendant

2.6 lb (1.18 kg)

2.65 lb (1.20 kg)

.19 lb (.09 kg)

4 lb (1.81 kg)

5 lb (2.27 kg)

1 lb (.45 kg)

Back Box:

2.85 lb (1.28 kg)

5 lb (2.27 kg)

Add 1.25 lbs (.57 kg) for heater and sun shield

Dome Drive:

Lower Dome:

2.65 lb (1.20 kg)

1.30 lb (.59 kg)

5 lb (2.27 kg)

2.20 lb (1.0 kg)

Add .25 lbs (.11 kg) for heater

TOP PORTION OF BACK BOX

DOME IS SECURED

IS REMOVABLE FOR SURFACE TO CEILING BY

MOUNT APPLICATIONS

MOUNTING BRACKET

8.52

(21.64)

7.25 (18.13)

6.60 (16.76)

5.25

(13.34)

6.75

(17.15)

10.90

(27.69)

5.83

(14.80)

3.25

(8.26)

5.90 (14.99)

8.25 (20.96)

5.90

(14.99)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

Figure 1. SD5 Series Dimension Drawing

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERAS

COLOR (Spectra II and Spectra Lite)

Signal Format:

NTSC (Spectra II dome drive models DD5BC, DD5BC22, and DD5BCBW)

PAL (Spectra II dome drive models DD5BC-X, DD5BC22-X, and DD5BCBW-X)

NTSC (Spectra Lite dome drive model DD5TAC)

PAL (Spectra Lite dome drive model DD5TAC-X)

Scanning System:

Image Sensor:

2:1 interlace

1/4-inch interline transfer CCD

Effective Pixels

NTSC Spectra II:

PAL Spectra II:

768 (H) x 494 (V)

752 (H) x 582 (V)

510 (H) x 492 (V)

500 (H) x 582 (V)

NTSC Spectra Lite:

PAL Spectra Lite:

Horizontal Resolution

Spectra II:

>470 TV lines

470 TVL (NTSC)

460 TVL (PAL)

Spectra Lite:

Lens

Minimum f-stop

Spectra II

16X:

18X:

22X:

Spectra Lite:

F1.4

F1.6

Focal Length

Spectra II

16X:

4 mm to 64 mm optical

4.1 mm to 73.8 mm optical

4 mm to 88 mm optical

3.9 mm to 63 mm optical

18X:

22X:

Spectra Lite:

Zoom Ratio

Spectra II

16X:

16X optical zoom, 8X electronic zoom

18X optical zoom, 4X electronic zoom

22X optical zoom, 8X electronic zoom

16 optical zoom

18X:

22X:

Spectra Lite:

Digital Slow Shutter:

Auto/manual speed selection

Horizontal Angle of View

Spectra II

16X:

47° (at 4 mm wide zoom),

3° (at 64 mm telephoto zoom)

48° (at 4.1 mm wide zoom),

2.7° (at 73.8 mm telephoto zoom)

47° (at 4 mm wide zoom),

18X:

22X:

2° (at 88 mm telephoto zoom)

45° (at 3.9 mm wide zoom),

3° (at 63 mm telephoto zoom)

Spectra Lite:

MTBF

16X:

>2 million cycles at room temperature (zoom, focus, irs)

>500,000 cycles at room temperature (zoom, focus, irs)

>2 million cycles at room temperature (zoom, focus, irs)

>1 million cycles at room temperature (zoom, focus, irs)

18X:

22X:

Spectra Lite:

Focus:

Automatic and manual override

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Sensitivity

Spectra II

16X:

18X:

.05 lux at 1/2-second shutter speed

.2 lux at 1/4-second shutter speed (color)

.013 lux at 1/4-second shutter speed (black & white)

.07 lux at 1/1.5-second shutter speed

22X:

Spectra Lite:

1 lux at f1.6 at signal level of 40 IRE, gain high (AGC on)

Sync System:

White Balance:

AC line lock, phase adjustable via remote control*

Automatic with manual override*

Shutter Speed Models

DD5BC, DD5BC22,

and DD5AM:

1/2-1/30,000*

DD5BC-X, DD5BC22-X,

and DD5AM-X:

DD5BCBW:

DD5BCBW-X:

DD5TAC:

1/1.5 to 1/30,000*

1/4 to 1/10,000*

1/3 to 1/10,000*

1/60 to 1/10,000*

1/50 to 1/10,000*

DD5TAC-X:

Iris Control

Spectra II:

Spectra Lite:

Automatic with manual override*

Gain Control:

Automatic with manual override*

Video Output

NTSC:

.714V ± .07V (100 IRE ± 10 IRE)

PAL:

.7V ± .07V

Signal to Noise Ratio:

>46 dB

MONOCHROME (Spectra II Only)

Signal Format:

EIA (model DD5AM)

CCIR (model DD5AM-X)

Scanning System:

Image Sensor:

2:1 interlace

1/4-inch interline transfer CCD

Horizontal

Resolution:

>500 TV lines

Effective Pixels

EIA:

768 (H) x 494 (V)

752 (H) x 582 (V)

CCIR:

Lens

Minimum f-stop:

Focal Length:

Zoom Ratio:

Horizontal

F1.4

4 mm to 64 mm optical

16X optical zoom, 8X electronic zoom

Angle of View:

47° (at 4 mm wide zoom),

3° (at 64 mm telephoto zoom)

MTBF:

Focus:

>2 million cycles at room temperature (zoom, focus, iris)

Automatic with manual override

Sensitivity

EIA:

.1 lux at f1.4, AGC gain 26.5 dB, signal level 40 IRE, without IR cut filter

.1 lux at f1.4, AGC gain 29.5 dB, signal level 300 mV, without IR cut filter

CCIR:

Signal Process:

Sync System:

DSP-3R

AC line lock, phase adjustable via remote control*

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Shutter Speed:

EIA:

Automatic (electronic iris)/manual

1/60-1/30,000

CCIR:

1/50-1/30,000

Iris Control:

Automatic with manual override*

Gain Control:

Video Output

EIA:

.714V ± .07V (100 IRE ± 10 IRE)

CCIR:

.7V ± .07V

Signal to Noise Ratio:

>46 dB

* Manual control of camera setup functions can be done with CM6700, CM8500, CM9500, CM9760 and MPT9500 controllers, but not

with CM7500, MPT9000 or KBD9000 controllers.

(Design and product specifications subject to change without notice.)

CERTIFICATIONS AND REGULATORY NOTICES

CE, Class A (models DD5BC-X and DD5BC22-X).

CE, Class B (models BB5A-F, BB5A-PB, BB5A-PG, BB5A-PG-E, BB5T-F, BB5T-PB, BB5T-PG, BB5T-PG-E, DD5TAC-X, DD5AM-X,

and DD5BCBW-X). (Model BB5A-PSG-E, Pending)

UL/cUL (models BB5A-F, BB5A-PB, BB5A-PG, BB5A-PG-E, DD5AM, BB5T-F, BB5T-PB, BB5T-PG, BB5T-PG-E, DD5TAC, DD5BC,

DD5BC22, and DD5BCBW). (Model BB5A-PSG-E, Pending)

FCC Class A (model DD5BC22)

FCC Class B (models DD5AM, DD5BC, DD5TAC, and DD5BCBW).

Suitable for use in environmental air handling spaces (BB5A-F and BB5T-F).

FCC Class B meets more stringent requirements than FCC Class A.

The following applies to the DD5AM, DD5BC, and DD5TAC models.

FCC Class B - This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the

FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The following applies to the DD5BC22 model.

FCC Class A - This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the

FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

Pelco Installation Manual C1487M-H (1/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

Exceptions to this warranty are as noted below:

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on FT/FR8000 Series ﬁber optic products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Three years on Camclosure^®and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a ﬁve-year warranty.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

•

Two years on standard motorized or ﬁxed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

•

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 scanners, including when used in

continuous motion applications.

•

Two years on Esprit^®and WW5700 Series window wiper (excluding wiper blades).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura^™Series distributed network-based video products.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments

C1487M

7/98

Original version.

C1487M-A 11/98 Revised the manual to incorporate Spectra Lite material. Added material on CCIR and EIA monochrome cameras, and PAL

color camera. Revised material in Section 5.11.21.2, Programming Limit Stops. Revised Section 6.0, Troubleshooting. Changed

the fixed-speed controller rate in Section 8.0, Specifications.

C1487M-B 2/99

Changed Spectra Lite model numbers, and added comments that the line sync feature is not functional for the DD5T-C model

of Spectra Lite. Changed power specifications for indoor models from 25 vA to 30 vA and for outdoor models from 90 vA to

75 vA. Revised maximum temperature operating ranges. Revised color camera specifications.

Changed auto iris material to include Spectra Lite as well as Spectra II.

3/99

C1487M-C 7/99

Added a note relating to running patterns when an alarm activates. Changed the preset tilt speed from 100 to 200 degrees/

second. Added model number and specifications for Spectra Lite PAL camera. Revised manual to new format.

C1487M-D 7/99

C1487M-E 9/99

Changed Spectra Lite camera zoom from 12X to 16X. Changed line sync and auto focus material to include Spectra Lite as

well as Spectra II. Removed auto iris peak and auto sharpness options for Spectra Lite. Added white balance hue option for

Spectra Lite and removed R-B and M-G white balance options for Spectra Lite. Revised Spectra Lite camera specifications.

Replaced the standard Spectra II DD5AC and DD5AC-X cameras with model DD5BC and DD5BC-X LowLight color cam-

eras. Added optional 176X color models. Revised main menu access documentation to include the KBD4000/KBD4002/

KBD4000V keyboards. Added material on LowLight limit. Revised material on shutter speed and zoom. Added material on

zone overlap and priorities. Revised color camera specifications.

C1487M-F 3/00

C1487M-G 5/00

C1487M-H 1/01

Separated into two manuals - Installation Manual and Operation and Programming Manual.

Added information on Spectra II Color/Black and White.

Added step to dome drive installation instructions referencing the new RS-422 termination switch. Revised specifications

and certifications.

® Pelco, the Pelco logo, Spectra, Genex, Legacy, and Coaxitron are registered trademarks of Pelco.

™ Spectra II, Spectra Lite, Esprit, and Camclosure are trademarks of Pelco.

® Loctite is a registered trademark of Loctite Corporation.

U.S. Patent No. 5,931,432.

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Microphone AAM 880 User Manual
Philips Clock Radio AJ3230 17 User Manual
Philips Electric Shaver 1090X User Manual
Philips Portable CD Player AQ 6542 User Manual
Philips Work Light Ballasts For Fluorescent Lamps User Manual
Pioneer Stereo Amplifier A A6 J User Manual
Planet Technology Network Card VIP 161SW User Manual
Poulan Lawn Mower 187594 User Manual
Poulan Tiller 184877 User Manual
Poulan Tiller RT900 User Manual