Installation and Assembly: Wallmount for CPA100 and
Whiteboard
Model: A100IWBMOUNT
Maximum Load Capacity for Screen: 53 lb (24 kg)
Maximum Load Capacity for Projector : 13.5 lb (6 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, make sure all parts shown are included with your product.
A
B
Parts List
Description
Qty. Part #
A wall mount assembly
B projector tube
C projector arm
D adapter plate
1
1
1
1
2
2
1
1
1
1
055-1841
055-1839
055-1830
055-1828
055-1840
055-1834
055-1858
055-1822
055-1821
PRG-1
E hook bracket
F vertical handle
G horizontal handle
H projector adapter plate
CARRIAGE
I
slide plate
J
projector mount
K #10-32 x 0.375" phillips screw
18 520-1130
L M6 x 12 mm serrated washer head socket pin screw
8
4
2
2
4
6
2
1
2
6
1
2
1
1
6
1
510-1050
590-1050
520-1606
520-1151
540-9460
5S1-015-C03
530-1049
590-1303
510-1098
590-0097
560-9646
520-1196
590-1271
055-1836
560-9711
ACC615
C
M
0.25"ID spacer
N 1/4-20 x 1.0" hex head screw
O #10-32 x 3/8" serrated washer head socket pin screw
P 0.25" ID nylon washer
Q #14 x 2.5" wood screw
R acorn nut
D
S plug
T #10-32 x 1-3/8" socket pin screw
U alligator anchor
V 5/32" (4 mm) security allen wrench
W #10-32 x 1/4" socket pin screw
X
Y
Z
flanged bushing
retainer bushing
cable tie
toggler pack
Parts may appear slightly different than illustrated.
E
F G
H
O
I
J
P
Q
M
N
K
L
R
S
T
3 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List Continued
W
X
Y
U
V
Z
Make sure that wall mount assembly (A) is level, use it as a template to mark the top two mouting holes.
Alternatively, the top two screws can be fastened 16" apart as detailed in step 2 while making sure that they are
level. In order to set the desired height of bottom of screen in the lowest position, refer to dimension X from the chart
below.
1
PROJECTOR
TOP
MOUNTING
HOLES
A
SCREEN
X
BOTTOM OF
SCREEN
FLOOR
CHART
Screen Size Dimension X
63"
77''
36"
42"
4 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Wood Stud Wall
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers
are responsible to provide hardware for other types of mounting situations.
Make sure that the mounting holes are on the stud centerline. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep.
Fasten two #14 x 2.5" wood screws (Q) into top mounting holes leaving a .25" of exposed thread as shown. Hook
wall mount assembly (A) onto #14 x 2.5" wood screws (Q) as shown in fig. 2.1.
2
Fasten four #14 x 2.5" wood screws (Q) into wall mount assembly (A) as shown in fig. 2.2. Make sure that the wall
mount assembly (A) is level, tighten all six #14 x 2.5" wood screws (Q).
Skip to step 3.
Q
A
.25"
CARRIAGE
CARRIAGE
fig. 2.1
A
Q
fig. 2.2
5 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Solid Concrete or Cinder Block
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
Use wall mount assembly (A) as a template to mark
mouting holes. Drill six 5/32" (4 mm) dia. holes to a
minimum depth of 2.5" (65 mm). Insert six anchors (U) in
2
concrete
surface
1
holes flush with wall as shown (right). Fasten two #14 x
2.5" wood screws (Q) into top anchors (U) leaving a .25" of
exposed thread for each screw (Q) as shown. Hook wall
mount assembly (A) onto #14 x 2.5" wood screws (Q) as
U
shown in fig. 2.3. Fasten four #14 x 2.5" wood screws (Q)
into wall mount assembly (A) as shown. Make sure that the
Drill holes and insert anchors (U).
wall mount assembly (A) is level, tighten all six #14 x 2.5"
wood screws (Q).
2
A
Skip to step 3.
U
Q
WARNING
• Tighten screws so that wall mount is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
Place wall mount assembly (A) over anchors (U) and
secure with screws (Q).
3
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
• Always attach concrete anchors directly to load-
bearing concrete.
Tighten all fasteners.
• Never attach concrete anchors to concrete covered
with plaster, drywall, or other finishing material. If
mounting to concrete surfaces covered with a finishing
surface is unavoidable, the finishing surface must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when tighten-
ing screws. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
Q
A
.25"
INCORRECT
CORRECT
CARRIAGE
concrete
wall plate
concrete
wall plate
plaster/
drywall
plaster/
drywall
Q
fig. 2.3
U
6 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 615 Required)
WARNING
• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes prior to
drilling 1/2" holes.
2
Refer to instruction sheet included with Peerless accessory kit ACC 615 for metal studs to install togglers.
Fasten two 1/4-20 x 2-1/2" screws into top mounting holes leaving a .25" of exposed thread on each as shown in
fig. 2.4. Hook wall mount assembly (A) onto 1/4-20 x 2-1/2" screws.
Fasten four 1/4-20 x 2-1/2" screws into wall mount assembly (A) as shown in fig. 2.5. Make sure that the wall mount
assembly (A) is level, tighten all six 1/4-20 x 2-1/2" screws.
1/4-20 X 2-1/2" PHILLIPS SCREWS
.25"
A
TOGGLER
CARRIAGE
CARRIAGE
A
fig. 2.4
1/4-20 X 2-1/2" PHILLIPS SCREWS
fig. 2.5
7 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fasten three #10-32 x 0.375" phillips
screws (K) to carriage leaving three
threads exposed.Attach retainer
bushing (Y) and flanged bushing (X) to
wall mount assembly (A) using two
#10-32 x 0.375" phillips screws (K).
Slide projector tube (B) into top of wall mount
assembly (A) and secure with two #10-32 x
0.375" phillips screws (K) as shown below.
NOTE: Use correct set of mounting holes for
the screen size as shown below.
K
4
3
Y
X
63" SCREEN
A
NOTE: Twist tube
into wall mount
assembly (A).
B
K
THREE
THREADS
EXPOSED
DETAIL 1
K
A
Hook adapter plate (D) onto three
#10-32 x 0.375" phillips screws (K).
4-1
CARRIAGE
K
D
77" SCREEN
K
B
Fasten three #10-32 x 0.375" phillips
screws (K) into adapter plate (D).
Securely tighten all six #10-32 x
0.375" phillips
4-2
A
D
CARRIAGE
K
K
8 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fasten two #10-32 x 0.375" phillips screws (K) into adapter plate (D) leaving three threads exposed as shown in
detail 1. Hook each vertical handle (F) onto #10-32 x 0.375" phillips screw (K) as shown in fig 5.1. NOTE: Use top
slot for 77" screen or second slot from top for 63" screen. Fasten #10-32 x 0.375" phillips screws (K) through lower
slot of vertical handle (F) that lines up with the lower hole in adapter plate (D). Hole location for 77" screen is shown
in fig. 5.2. Securely tighten all four #10-32 x 0.375" phillips screws (K).
5
DETAIL 1
K
K
D
THREE THREADS
EXPOSED
D
K
NOTE: 77" hole location
shown. 63" will use second
from bottom hole on vertical
handle (F).
77" SCREEN
63" SCREEN
F
F
fig. 5.1
fig. 5.2
Fasten horizontal handle (G) to vertical handle (F) using four #10-32 x 0.375" phillips
screws (K) and two acorn nuts (R).
6
F
K
K
CABLES ROUTING THROUGH THE TUBE
CAN BE PULLED TAUGHTAND FIXED IN
LINE TO THE HORIZONTALHANDLE(G) BY
USING CABLE TIES (Z). USE OTHER CABLE
TIESAS NEEDED.
R
G
9 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert hook brackets into screen as shown in detail 2 and fig. 7.1. Secure each hook bracket (E) with M6 x 12 mm
serrated washer head socket pin screw (L) as shown in fig. 7.2 and detail 3.
7
SCREEN
SCREEN
BRACKET
63" SCREEN
E
77" SCREEN
DETAIL 2
fig. 7.1
SCREEN
E
L
DETAIL 3
fig. 7.2
10 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hook brackets (E) into adapter plate (D) as shown in fig. 8.1 and
detail 4. The hooks will go over the flange on the top and the bottom of
hook bracket (E) into the slots as shown in detail 4 and detail 6. Fasten
#10-32 x 1-3/8" socket pin screws (T) on each hook bracket (E), using
security allen wrench (V) and tighten to wall plate as shown in
detail 5.
HOOK
8
E
FLANGE
To remove screen from mount, loosen safety/security screws and lift screen
off of mount.
D
CAUTION
DETAIL 4
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
D
E
T
D
BOTTOM OF HOOK
BRACKET (E)
E
D
DETAIL 5
SIDE VIEW
fig 8.1
DETAIL 6
fig 8.2
Disengage connection block from projector mount assembly (J) by unscrewing captive screw and sliding out
9
connection block as shown.
J
CONNECTION
BLOCK
CAPTIVE
SCREW
11 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrow on projector mount assembly (J) indicates front of mount. The arrow of projector mount assembly (J) should
face towards the round tube on projector arm (C).
10
Fasten projector mount assembly (J) to projector arm (C) using two 1/4-20 x 1.0" hex head screws (N), four 0.25" ID
nylon washers (P) and slide plate (I) as shown in fig. 10.2 and 10.3. Do not tighten 1/4-20 x 1.0" hex head
screws (N) fully to allow for adjustment. Insert rectangle plug (S) into projector arm (C) as shown in fig. 10.2.
Position projector mount assembly (J) so that hole corresponding to your size screen in projector arm (C) is in the
center of projector mount assembly (J) as shown in fig. 10.1. Securely tighten both 1/4-20 x 1.0" hex head screws
(N). NOTE: This can be adjusted during final projector alignment if needed.
C
N
ROUND TUBE
J
fig. 10.2
P
77" SCREEN
63" SCREEN
ARROW INDICATES
FRONT OF MOUNT
I
S
N
J
C
P
Bottom View
fig. 10.1
I
C
FRONT VIEW
fig. 10.3
12 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Place projector arm (C) onto projector tube (B) as shown in fig. 11.1. Align projector arm (C) so that the holes in
projector tube (B) are in the middle of projector arm (C) slot. NOTE: This can be adjusted during final projector
alignment if needed. Fasten projector arm (C) to projector tube (B) using two #10-32 x 3/8" serrated washer head
socket pin screws (O) as shown in fig. 11.2 and detail 6.
11
C
B
fig. 11.1
C
B
O
DETAIL 6
fig. 11.2
13 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching Adapter Plate to Projector
Align shoulder on connection block opposite notch in
adapter plate (H). Attach adapter plate (H) to
connection block from projector mount assembly (J)
using two #10-32 x 3/8" serrated washer head socket
pin screws (O).
CONNECTION
BLOCK
12
SHOULDER
H
NOTCHINDICATES
FRONTOF
PROJECTOR
O
Attach adapter plate (H) to projector using
13
four M6 x 12 mm serrated washer head
socket pin screws (L) and 0.25" spacers (M).
NOTE: Shoulder of connection block indi-
cates the back of projector. The screws (L)
should be placed in the center of slots. This
can be adjusted during final projector
alignment if needed.
L
SHOULDER
H
CONNECTION
BLOCK
M
PROJECTOR
14 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching Adapter Plate to Projector Mount
WARNING
• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle
placement of the projector.
Slide connection block with projector into projector mount assembly (J) as shown. Tighten captive screw to secure
14
projector to projector mount assembly (J).
ARROW INDICATES
FRONT OF MOUNT
CONNECTION
BLOCK
J
FRONTOF
MOUNT
CAPTIVE
SCREW
IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (W) through projector mount
assembly (J) and into connection block as shown. Tighten screw using 4mm security allen wrench (V).
15
J
W
CONNECTION
BLOCK
15 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Alignment
To adjust yaw (swivel): Loosen screw on projector mount assembly (J) indicated below until projector mount
can be rotated. Rotate mount to desired position and retighten screw.
16
To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and
turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand
for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
J
KNOBFORPITCH
ARROW INDICATES
FRONT OF MOUNT
ADJUSTMENT
SCREWFORYAW
(SWIVEL)STOP
BACKOFMOUNT
KNOBFORROLL
ADJUSTMENT
fig. 16.1
To prevent tampering with the pitch and roll adjustments: Tighten the two tamper resistant security screws
on the projector mount assembly (J) using 4 mm security allen wrench (V) to lock the pitch and roll adjustments
as shown below.
16-1
NOTE: Tighten screws firmly, but do not overtighten. Overtightening can damage the mount.
CAUTION
• Do not adjust pitch or roll while tamper resistant security screws are fully engaged.
• Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly or
damage may occur.
TOLOCKROLLTIGHTEN
TOLOCKPITCHTIGHTEN
TAMPER RESISTANT
SECURITY SCREW
TAMPER RESISTANT
SECURITY SCREW
FRONT VIEW
SIDE VIEW
16 of 16
ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
For customer care call 1-800-865-2112 or 708-865-8870.
©2008, PeerlessIndustries, Inc. Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Download from Www.Somanuals.com. All Manuals Search And Download.
|