SL
EL
Jiva SL & Jiva EL
(TP-5700/5800)
SERIES
USER’ S MANUAL
WORK STATION
Rev. : Original
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
BRIEF INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
THE USER’ S MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Available Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Optional Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
FRONT VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
SIDE VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
Right Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
Left Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
REAR VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
REAR VIEW OF MAIN UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
ADJUSTABLE STAND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . 2 - 4
BOTTOM OF STAND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 2 - 4
CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5
INSTALLATION GUIDES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
SEPARATING MAIN UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
PREPARING STAND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 3 - 2
INSTALLING UPS BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
ROUTING THE CABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
PREPARING THE MAIN UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
JOINING MAIN UNIT AND STAND . . . . . . . . . . . . . . . . . . . . . . 3 - 4
OPENING CABLE COVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5
CONNECTING CABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5
i
Download from Www.Somanuals.com. All Manuals Search And Download.
WALL MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6
LOCATION FOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 3 - 6
OPERATING SYSTEM RECOVERY . . . . . . . . . . . . . . . . . . . . . 3 - 7
USING THE TOUCH POS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
APPLICATION ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
POWER ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Hardware Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2
Software Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3
DISPLAY RESOLUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3
External Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3
SECURITY DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3
SERIAL PORTS – COM1/2/3/4 . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3
SOUND PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - 4
TOUCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - 4
TOUCH PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4
TOUCH TERMINAL MANAGER . . . . . . . . . . . . . . . . . . . 4 - 5
RS232 TOUCH MONITOR MOUSE . . . . . . . . . . . . . . . . 4 - 5
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
BRIEF INTRODUCTION
THE USER’ S MANUAL
The purpose of this manual is to guide the user in the initial installation and
general use of the Posiflex fully integrated compact touch interface workstation. Jiva
SL & Jiva EL (TP5700/5800) series is a product group of fully integrated PC based
Point-Of-Sale systems. However, this manual does not intend to explain any
application program that may be supplied with the systems. The user should consult
the software supplier or the VAR that he purchased from for such information. The
for further information of our products.
THE PRODUCT
Overview
The Jiva SL & Jiva EL series is one of the most compact yet fully integrated
touch terminal systems. This series helps user achieve lowest TCO (Total Cost of
Ownership) not only by its strong support to server based application that is well
known for tremendous cost savings in both hardware and software update but also by
its extremely low service cost through a number of unique design features like
excellent heat dissipation and its support to Linux system.
Configuration
AVAILABLE MODELS
Jiva SL & Jiva EL series offers several selections for basic models. Jiva SL is
supplied without HDD but with CF memory card. Jiva EL is supplied with HDD to
work as fat client in two tier architecture. Other choices are: LCD panel size as 12.1”
or 15”; PS2 or RS232 interface touch controller.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 1 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD FEATURES
a) CPU: Celeron compatible 400 MHz up
b) HDD: available for fat client models
c) Support Win98, Win2000 in fat client models, and WinCE, Win XP
embedded & Linux environment throughout whole series
d) Support thin client architecture either boot from WinCE in CF card or
Linux LAN boot
e) Fanless design (for thin client models) to reduce dust/grease accumulation
f) High quality 12.1” / 15” TFT active matrix LCD panel
g) Vertical type LCD panel with easy tilt angle adjustment from 18° to 87°
h) Height adjustment: the high / low adjustment gives 20 mm difference in
height
i) Resistance type touch panel
j) Extra long life touch panel that endures 10 million up to 35 million
touches at same spot
k) Spill proof water resistant structure allowing easy cleaning
l) Easy maintenance construction
m) Various I/O ports supported, including:
1. one PS/2 KB port
2. one PS/2 mouse port
3. 4 serial ports with capability for +5V DC support unless otherwise
occupied
4. one parallel port
5. 2 USB ports
6. one LAN port 10/100 base T Ethernet
7. one external VGA monitor port
8. one Compact Flash memory card connector (for thin client
terminals only)
9. one external CD ROM drive connector (for fat client terminals
only)
10. one DC 12 V input connector
11. one UPS battery connector
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 1 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
12. one CR port for control over 2 cash drawers max.
13. audio ports (1 Microphone input and 1 audio line output)
n) Touch control functions: left/right button, double click, drag & draw
o) High resolution touch sensor: 1024 x 1024
p) Dual display support
q) VGA memory size shared from system memory (8 – 64 MB)
r) Support high performance DDR266 DRAM with maximum memory size
1GB in two modules
s) Integrated structure for optional security devices (incl. 40 keys
programmable keypad, smart card reader, finger print sensor, iButton
reader, MSR)
t) Software programmable MSR parameters in KP100 for embedded Win 98
or embedded Win XP
OPTIONAL ITEMS
Note: The underlined items in the following list means that option must be set
prior to shipment from the factory. The rest items can be set by the
dealers.
a) DDR266 DRAM memory expansion up to 1GB
b) Deluxe security device upgrade (KP100) covering keypad and option(s)
from KB interface MSR, smart card reader and finger print sensor
c) Common security device upgrade (SD100) covering option(s) from USB
interface MSR or smart card reader and finger print sensor or iButton
reader
d) Integrated rear top mount LCD customer display PD-302
e) VFD PD-2500 or graphic LCD PD-7100 stand alone Posiflex pole display
f) Preload OS
g) External 12” LCD monitor LM-6000 series
h) External CD ROM drive
i) Wall mount kit
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 1 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 1 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS IDENTIFICATION
FRONT VIEW
Security Devices Upgrade Unit
Display Screen
+ Touch Panel
Main Unit
Adjustable
Stand
Assembly
The security device and top mount LCD customer display are options to both
12” and 15” models. The LED in the logo area serves for several purposes through
giving different indication of steady/flashing green/blue light. Please refer to the
paragraph discussing the LED indication in the chapter of “USING THE TOUCH
POS” of this manual.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 2 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE VIEWS
Right Side View
Latch Hole For Cable Cover
Push
In
This
Direction To Adjust
The Tilt Angle Of
The Display Panel
Lock/Release Lever
Left Side View
Push Down To Switch
The Power ON/OFF
Latch Hole For
Cable Cover
Slide Switch For Power On/Off Control
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 2 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR VIEW
Lock/Release
Button To
Detach The
Main Unit
Optional
Security
Devices
Lock/Release
Lever
Cable Exit
REAR VIEW OF MAIN UNIT
Service Window
Matching Pegs
Cable Exit
Cable Cover
Removal Hollow Of Cable Cover
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 2 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTABLE STAND ASSEMBLY
Matching Holes
Stand
Base
Lock/Release Lever
BOTTOM OF STAND ASSEMBLY
Base
UPS Battery
Cable Passage
Cover
Cover
Lock/Release
Button For
Main Unit
Cable Exit
Stand
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 2 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTORS
Turn Counterclockwise Then
Take Out The Latch Key
Pull The Cable Cover
Out In This Direction
Locations of I/O Ports in original revision:
★CF Card Port
PS2 KB
LPT Port
★CDROM Port
COM2 Port
PS2 Mouse
LED Connector
CR Port
Power Input Jack
Audio Out Port
Audio (Mic) Input Port
UPS Battery Connector
COM1 Port
LAN Port
★
COM3 Port
USB1 Port
USB0 Port
External VGA Connector
★ CF Card Port is available in thin client models only.
★ CDROM Port is available in fat client models only.
★ COM4 Port will be plugged out in RS232 touch controller models.
Number and locations of the I/O ports may vary with progress in product life. Please
check the actual ports of physical existence if you receive a later version system.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 2 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 2 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION GUIDES
CAUTION: Before any installation or cable connection to the set, please always
make certain that the system is turned off and the external power
source to the set is removed to prevent electric hazard! Never touch
any metal pin in the connectors or circuits to avoid high voltage
hazard or electrostatic discharge damage unless the operator is well
grounded. Failure to do the above will void the product warranty!
SEPARATING MAIN UNIT
In order
Press the Lock/Release button
to settle the
and lift the main unit to
touch terminal
detach it from the
properly in a
stand assembly.
point of sale
system, all the
cable connections have to be routed through its base, the stand assembly. Therefore,
please press the lock/release button at the rear side to separate the main unit from the
stand assembly after all cables in cable cover disconnected.
Press the Lock/Release button and slide the stand
assembly downward (as viewed from
the main unit) to detach it from
the main unit.
A soft clean flat surface, such as a piece of cloth on the desk.
However, in view of the mass distribution of the whole assembly, it is most
recommended to lay the system facing down on front panel over a soft clean flat
surface first, such as a piece of cloth on the desk. Press the button and slide the stand
assembly downward (as viewed from the main unit) to detach the stand assembly
away from the back of the main unit could then be an easier operation. This approach
can also be applied when later on the main unit and the stand assembly have to be
reunited.
Jiva SL & Jiva EL (TP5700/5800) USER’S MANUAL 3 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARING STAND ASSEMBLY
Take the adjustable stand assembly and turn it up side down to show the
bottom of the base.
2 Sets of 4 Matching Holes
Screws
Cable
Passage
Cover
Adjustable
Stand
Now, unscrew the 2 screws on the
cable passage cover and take the cable
passage cover away to show the cable
passage.
Lock/Release
Lever
If there is no need to install the optional UPS battery here (either not to be
installed or already installed), please skip the next paragraph and start routing cables
through the cable passage. Otherwise, please remove the four screws holding the
battery cover to install the battery.
Four Screws
Holding
Battery Cover
Cable Passage
Battery Cover
Cable Passage
Cover
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 3 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING UPS BATTERY
UPS Battery
Removed
Battery
Cover
Place the optional UPS battery in the battery compartment (shown top left).
Screw on the battery cover and route the battery cable through the base. Please enable
the UPS features in the software settings before use.
ROUTING THE CABLES
Place all the cables required for connections to the
Jiva SL & Jiva EL (TP5700/5800) series except those for
special application purposes into the cable passage. Insert
one end of the cable passage cover under the adjacent
cover plate and screw on the two
screws. Be sure not to damage any of
the cables during this operation.
Now, turn the adjustable stand assembly back to normal
orientation and arrange all cables to come out of the area for
mounting main unit from the bottom edge for ease of later
operation.
PREPARING THE MAIN UNIT
On the back of the main unit, there are 4 matching pegs and a service window.
Push open the service window in the direction as indicated in the picture, one can find
a button cell battery socket, a 1 x 3 header (JP10) with 1 jumper and a 2 x 3 header
(JP8) with 2 jumpers. Though it is possible that the contents in the service window
may change as time develops.
Jiva SL & Jiva EL (TP5700/5800) USER’S MANUAL 3 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Window
4 Matching
Pegs
Push Open
To The
Right
This battery socket accepts a 3 V button cell Lithium battery (CR2032)
required to support the system real time clock. The jumpers in this window are
designated for COM port power supply function. Please consult your dealer for
technical support on setup of these jumpers. A new Lithium battery can support the
system RTC for about 3 years. After the battery is nearly exhausted, the user must
change a new battery otherwise the system RTC and system configuration setup will
be lost.
JOINING MAIN UNIT AND STAND
Matching Pegs
Matching Holes
Round Part
Slot Part
Removal
Hollow
Match the matching pegs on the back of the main unit against one of the two
sets of matching holes on the stand. It is recommended to hook on the lower set of
holes for better stability. First aim the matching pegs toward the upper round part of
the hole and make sure that all pegs are inside the holes. Then slide the main unit
down to move the pegs into the lower slot part of the holes till it clicks. Note that all
the cables come out of the stand from the lower edge and won’ t get trapped by this
mounting operation. If later on you want to remove the main unit from the stand,
you’ ll have to press down the lock/release button on back of the stand at the time
lifting the main unit.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 3 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPENING CABLE COVER
Insert the tip of the latchkey into a latch hole on one side near bottom of the
main unit. Turn this key counterclockwise to the end. Do the same on the opposite
side. Be sure to take the key out of the hole.
Turn Counterclockwise
Then Take Out The
Latchkey
Then push the lock/release lever on the base backward to adjust the stand to
the most horizontal position for ease of operation. Open the cable cover by pulling at
the removal hollow.
Pull The Removal Hollow
Toward The User
CONNECTING CABLES
Connect the cables required to the appropriate connectors. Please make sure
that each connector has to be connected to the right port in the right orientation. Some
connectors have to be inserted till a click is heard such as the LAN connector and the
CDROM port connector. It is recommended to screw on the connector once it is
inserted such as the external VGA connector, the LPT port connector and the COM
port connectors. Adjust the slack of each cable and close the cable cover. Use the
same latch key as when opening the cable cover but this time turn it clockwise on
Jiva SL & Jiva EL (TP5700/5800) USER’S MANUAL 3 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
both sides to secure the cable cover on the main unit. Adjust the tilt angle of the main
unit for best viewing effect in the application.
CAUTION: On doing any insertion or extraction of any connector, please always
hold the connector head itself instead of pulling on the cable wire.
Failure to do this could damage the cable and jack that is considered
as an artificial destruction and is not covered by the warranty.
WALL MOUNTING
The major part in the wall mounting kit is a bracket as shown in the picture.
Screw the bracket against the wall for mounting the Jiva SL & Jiva EL (TP5700/5800)
series in the direction that the wider parts of the matching holes are at the top as
shown in the picture. Align the four matching pegs on the back of the main unit with
the four matching holes in the bracket to hold the main unit in the similar manner as
installing the main unit onto the stand assembly. The stand assembly is not engaged in
wall mount operation.
Matching Holes
Wall Mount Bracket
Screw At Screw Holes Through Matching Holes
LOCATION FOR INSTALLATION
As the stand assembly is not involved in wall mount installation, the space
required for wall mount application will take only the main unit into consideration. So
the space required is 375 mm in width and 315 mm in height.
For desk top/counter application, the adjustable stand assembly requires a base
of 270 mm deep and 260 mm wide. However, please take also the main unit into
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 3 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
consideration. If the main unit is tilted to near vertical position, the total height can be
either 360 mm or 380 mm depending on the position adjusted. When the main unit is
tilted to near horizontal position, the total height required is 275 mm.
OPERATING SYSTEM RECOVERY
For TP5712 and TP5715 models, if not using a remote boot operating system,
the operating system exists in the Compact Flash Card. Therefore, once the Compact
Flash is damaged for any reason, the thin client may fail to boot. A bootable new
Compact Flash Card will be required to have the workstation back to work.
Please follow instructions given by the System Integrator to deal with situations like
that. One more advice for CF Card application is that in spite of the fact that it is used
in the way like an ordinary HDD, usual system management utility such as
FDISK.EXE or FORMAT.COM shall never be used on CF Card otherwise the
boot sector of operating system itself may be damaged and causing the CF Card no
longer bootable.
For TP5815 models, the operating system exists in the HDD. Once the
software system on HDD collapses, it is possible to restore the operating system onto
a physically intact HDD with use of the Recovery CD that comes with the preloaded
operating system. Please follow the instruction from your system integrator for system
/ software restoration. Follow the instructions below for operating system recovery
only if your system integrator does not advise otherwise.
For the Jiva EL (TP5815) models preloaded with Windows XP embedded or
Windows 98 embedded on HDD, Posiflex provides recovery CD delivered with the
touch terminal for the preloaded operating system. The System Integrator shall take
care of software restoration after OS recovered.
Please use the re covery CD in rescue operation only. Using it otherwise
may wipe out whatever stored in the HDD! All upgrade devices drivers needed for
manual installation in usual way are available in the subfolder “\drivers” in OS
recovered HDD and the latest versions of these required drivers will be available on
Now please follow instructions from your system integrator for software
recovery.
Jiva SL & Jiva EL (TP5700/5800) USER’S MANUAL 3 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 3 - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE TOUCH POS
APPLICATION ENVIRONMENT
It is very important that you check the following operational guidelines:
Ventilation
This terminal must NOT be operated in an environment with restricted
ventilation. The installation should be such that there is at least 25mm air clearance
around any top or side ventilation holes. The installation must also be such that there
is a free flow of air around the unit at ALL times.
Operating Environment
The equipment must not be operated or stored in extremes of both temperature
and humidity/moisture.
(Operating range 5°C to 40°C and up to 80% humidity – non condensing)
Power Supply
The operating voltage range of the power adaptor should cover the local power
supply for proper operation. The power cable, the power outlet and any power fusing
arrangements must conform to local safety regulations.
Please never do any connection / disconnection when system is still powered
on. Please always keep the external power adaptor in a free air circulation.
POWER ON/OFF
LED Indicator
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 4 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
There is an LED in the logo area or under the printed logo for system revision
that serves for several purposes. The relationship between LED status and other
conditions is summarized in following table:
LED Status
System Status External Power UPS Battery Powering Up
Off
Off
Off
Off
Off
On
On
On
Off
Off
On
On
Off
Off
Not present Not possible
Present
Not allowed
Allowed
Green
No influence
Blue
No influence Not required
Blue/flash
Green/rapid flash
High
Low
Not required
Not required
Hardware Switch
The power switch located at left side of the main unit is a slide type switch.
This switch controls the power on/off of the system. This switch turns the system on
when slid downward, only when external power is present. The switch will always
spring back to its original position when pressure is removed. This switch turns the
system off when slid downward again during power on status. However, if the system
hangs due to any reason such as software resource conflict a simple slide of the switch
may fail to turn off the power. In this case, please utilize the forced power off
feature by pressing the switch downward, and holding for within 10 seconds. In case
the turmoil is so vigorous that some hardware registers may be confused causing
trouble for system restart or even this forced power off, please disconnect the UPS
battery if installed and the AC power supply for few minutes. This may allow all
hardware registers to reset.
This switch can also be programmed as an ON only switch. That means, if the
application program issues a command compliant with the Jiva series technical
manual, this switch will always turn the system on when activated, but will not power
off the system when depressed again (the forced power off feature will not work in
this mode). When using this feature, please make sure that the software application
has the ability to power off the machine. In preloaded Windows, “Posiflex Power
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 4 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch Manager” in “Posiflex Tools” in the Program Files helps managing these
functions.
Software Support
The Jiva series provides a software power off command for application
program maneuvers. The Jiva also provides a specific means for the software to detect
if the system is working on external or UPS battery power. Due to this feature,
compatible software applications have the ability to change operating conditions when
running on standard/backup power. The software programmer may take reference
from the Jiva technical manual to apply such features.
DISPLAY RESOLUTION
For best viewing result please set your display resolution of TP5X12 at 800 x
600 with high color in the operation system. For TP5X15, please set the display
resolution at 1024 x 768 with high color.
In configuration of system memory, max. 64 MB can be shared as the video
memory.
External LCD Monitor
The external VGA port in the Jiva SL & Jiva EL series supports LM6000/6001
LCD monitor. This port supports either mirror mode (identical image) or extended
mode dual display function. To support the DC powered Posiflex LCD monitor, an
internal jumper must be set to supply the required power through the connector.
SECURITY DEVICES
Please follow the instructions on the manual that comes along with the security
devices SD100 or KP100 when it is installed.
SERIAL PORTS – COM1/2/3/4
In Jiva SL & Jiva EL series, there are 4 serial ports available except those
models using RS232 touch interface. All the serial ports can supply a +5 V DC
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 4 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
through pin 9 after proper jumper setting change. All 4 ports are standard RS232
serial ports.
When a serial Modem is to be used in Jiva SL & Jiva EL series, it is most
recommended to use COM2 or COM3 port for this purpose. In this way any hardware
resource conflict is eliminated and the MODEM ring up function can be supported.
For RS232 touch interface models, COM4 is occupied and covered. Please never try
to open the cover. Otherwise the product warranty is voided.
SOUND PORTS
The audio port on Jiva SL & Jiva EL series supports a Microphone in and a
line out jacks. The internal audio output port supports line output signals and requires
power amplifier for connection to speaker.
TOUCH FUNCTIONS
Following sections discuss about the touch control functions.
TOUCH PANEL
The touch panel in Jiva SL & Jiva EL series uses either a PS2 interface or an
RS232 interfaced. When its driver is properly installed, this touch panel works exactly
like a standard mouse. However, if the system is running under safe mode due to a
previous improper shutdown or for any other reason, most drivers are disabled in this
mode and the touch panel calibration may not coincide with the mouse pointer. It is
recommended that a standard PS2 mouse or keyboard be used in this mode.
All the below mentioned mouse emulation functions can be manipulated
through relevant software. The system can give a beep when the touch panel is
touched and can respond as if the left button of a PS2 mouse is clicked at the point
touched. If the point touched is dragged across the screen surface, it can respond as
though it is using the mouse drag and drop feature. If the point is touched, released
and touched within a short time interval, it will simulate double-clicking the mouse.
For the standard PS2 interface touch panel controller in Windows 98, touching the
screen for a while followed by a slight move of the touch without leaving the screen
surface will result in a right button mouse click. For the RS232 interface touch panel
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 4 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
controller, touching any point on the screen surface after touching the right-click
sticky button results as a click on the right button of the mouse at that point. However,
the right button function is applicable only under the WIN 98 environment.
TOUCH TERMINAL MANAGER
The touch panel control parameters are already well calibrated in the factory
prior to delivery. In principal, the touch panel requires no further calibration once
properly set. However, a program named “Posiflex Touch Terminal Manager” is
installed in the preloaded Windows system for the user to maneuver versatile features
of the touch terminal with a PS2 interface touch panel controller. This program can
also be obtained by download from the POSIFLEX web site. For an RS232 interface
touch panel, the touch panel portion of the following section should be disregarded.
Please refer to the paragraph titled “RS232 TOUCH MONITOR MOUSE” instead.
This program also controls the beep generated when the touch panel is touched,
the detail in right button click emulation, and also provides touch panel re-calibration.
RS232 TOUCH MONITOR MOUSE
If the Jiva EL purchased is RS232 touch interface models, the touch panel uses
an RS232 interface controller. The “Touch Panel Manager” of the above “Posiflex
Touch Terminal Manager” should be disregarded and a separate software called
Monitor Mouse should be used. In these models, the COM4 position of the system
will be covered in the connection area. Removal of this cover will void the product
warranty!!
In principle, the driver is installed with the systems equipped with the RS232
touch controller. However, if a re-installation is required, please select “SmartSet
Serial Controller on COM4” as the controller type during the installation process.
Once the RS232 touch controller driver is installed, the user can utilize it to
calibrate the touch screen, define mouse button emulation modes, enable right button
emulation or define the click sound’ s tone and duration. Please click “Start”, “Setting”,
“Control Panel” and “Elo Touchscreen” to engage this utility. However, with this
touch controller driver, certain display mode like full screen display of Windows DOS
box should be avoided.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 4 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
If, for any reason, the user wants to remove the driver for the RS232 touch
controller, please select “Monitor Mouse for Windows 95” in the program list for
removal.
Jiva SL & Jiva EL (TP5700/5800) USER’ S MANUAL 4 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|