USER
MANUAL
MODEL 1000RC
Asynchronous Short
Range Modem:
Dual Rack Mount Card
SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
Part# 07M1000RC-B
Doc# 052011UB
Revised 4/30/96
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 GENERAL INFORMATION
3.0 CONFIGURATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for One Year parts and labor. If any questions or problems
arise during installation or use of this product, please do not hesitate to
contact Patton Electronics Technical Support at (301) 975-1007.
This section describes the location and orientation of the Model
1000RC's configuration straps, provides detailed instructions on setting
each strap and describes the settings for each of the rear connection
cards.
The Model 1000RC uses two sets of configuration straps. These
straps are accessible when the card is slid out of the rack chassis (see
Figure 1, below). Once configured, the Model 1000RC is designed to
operate transparently, without need for frequent re-configuration: just
set it and forget it!
2.1 FEATURES
• Convenient rack card features two short range modems
• Data rates to 19.2 Kbps
JP1-A
• Full duplex operation
ON
• Supports distances to 17 miles
• Features 13 front panel LEDs
• Silicon Avalanche Diode surge protection
• Fits conveniently in Patton’s rack chassis
• Made in USA
1
2
3
Normal
ON
1
2
3
Normal
JP1-B
2.2 DESCRIPTION
Figure 1. Model 1000RC card, showing location of configuration jumpers
3.1 STRAP LOCATIONS AND ORIENTATION
The Model 1000RC Asynchronous Short Range Modem Rack
Card is a dual rack card incorporating two short range modems. Both
units operate full duplex at data rates to 19.2 Kbps over 2 twisted pairs
and support distances to 17 miles. The Model 1000RC features 13
easy-to-read front panel LEDs, which monitor the status of data
transmission. The Model 1000RC also incorporates Silicon Avalanche
Diodes for protection against the damaging effects of nearby lightning
strikes and other harmful transients.
The configuration straps on the Model 1000RC board allow you to
configure the function of both “Carrier Detect” outputs. Figure 2 shows
the orientation of these straps. Notice that each strap can either be on
pegs 1 and 2, or on pegs 2 and 3.
The Model 1000RC uses the latest surface mount technology to
attain high quality short range modem performance in a convenient
rack card. Filling one function card slot on Patton’s Model 1000R16P
rack chassis, the Model 1000RC is available with RJ-11 or RJ-45 rear
interface cards. For workgroup and desktop communications, the
Model 1000RC also fits in Patton’s 2, 4 and 8 slot Cluster Boxes. The
combination of rack mount, Cluster Box and self-powered units
provides a completely integrated Model 1000 “networking” solution.
1
2
3
1
2
3
1
2
3
Figure 2. Orientation of interface card straps
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 FRONT CARD CONFIGURATION
3.3.1 REAR CARD STRAP SETTINGS
The Model 1000RC contains two sets of configuration straps which
allow you to set the function of “Carrier Detect” output. Since the Model
1000RC contains two modems, each unit can be configured separately:
Jumper 1 (JB1) controls Unit A, while Jumper 2 (JB2) controls Unit B.
Figure 5 shows the strap locations for the 1Q11 and the 1Q45 rear
cards. These straps determine various grounding characteristics for
the RS-232 and twisted pair lines.
1
2
3
JB2
Each “Carrier Detect” strap can be set to “Normal” or “Always on”.
When operating normally, the “CD” LED will blink to indicate the
presence or absence of the carrier. When set to “Always on”, the “CD”
LED will always indicate that the carrier is “ON”. Figure 3 (below)
summarizes the switch settings.
(Unit A)
Converter
twisted pair
}
(Unit B)
JB4
1
2
3
(Unit A)
INTERFACE CARD JUMPER SUMMARY TABLE #1
1
2
3
Terminal
Jumper
JP1-A
Function
Position 1&2
Always ON*
Always ON*
Position 2&3
Normal
}
JB6
(Unit B)
Carrier Detect - Unit A
Carrier Detect - Unit B
JB7
1
2
3
1
2
3
JB5
JP1-B
Normal
Figure 3. Summary of jumper settings, *indicates factory default
Figure 5. Strap locations for both rear cards
3.3 REAR CARD CONFIGURATION
Figure 6 provides a summary of strap functions for both of the rear
cards. The next page describes each strap's function.
The Model 1000RC has two interface card options: the 1Q11 (which
comes equipped with two RJ-11 ports and two RJ-45 ports) and the
1Q45 (which comes equipped with four RJ-45 ports). Figure 4
illustrates these two different rear interface options.
INTERFACE CARD STRAP SUMMARY TABLE #1
Strap
JB2
JB4
JB5
JB6
JB7
Position 1&2
Line A Shield
Line B Shield
SGND & FRGND*
Unit A DSR†
Position 2&3
No Shield†
No Shield†
1Q11
1Q45
Open (Not Connected)†
RJ-11/6
RJ-11/6
RJ-45/10
RJ-45/10
RJ-45/10
N/A
Unit B DSR†
N/A
Figure 6. Summary of strap settings, † indicates factory default
RJ-45/10
RJ-45/10
*via 100 ohm resistor
RJ-45/10
Line A Shield & Line B Shield (JB2 & JB4)
This strap pertains to the line interface. In position 1&2, the strap
links RJ-11 pins 1 and 6 (RJ-45 pins 2 and 7) to frame ground and the
rear panel. These pins can be used as connections for the twisted pair
cable shield. In position 2&3, pins 1 and 6 (or 2 and 7) are
disconnected from frame ground.
Figure 4. Model 1000RC rear interface card options
Prior to installation, you should examine the rear card you have
selected and ensure that it is suitable for your application. Each rear
card is configured by setting straps on the PC board. Section 3.3.1
describes the strap locations and settings for each card.
(continued)
6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 INSTALLATION
JB2
Position 1&2 = Line A Shield Connected to Frame Ground
Position 2&3 = No Shield
This section describes the functions of the Model 1000R16P rack
chassis, tells how to install front and rear Model 1000RC cards into the
chassis and provides diagrams for wiring up the interface connections
correctly.
JB4
Position 1&2 = Line B Shield Connected to Frame Ground
Position 2&3 = No Shield
4.1 THE MODEL 1000R16P RACK CHASSIS
SGND & FRGND (JB5)
The Model 1000R16P Rack Chassis (Figure 7) has sixteen short
range modem card slots, plus its own power supply. Measuring only
3.5” high, the Model 1000R16P is designed to occupy only 2U in a 19”
rack. Sturdy front handles allow the Model 1000R16P to be extracted
and transported conveniently.
In position 1&2, this strap links signal ground and frame ground
through a 100 Ohm, 1/2 W resistor. In position 2&3, pin 1 is “not
connected to frame ground.
JB5
Position 1&2 = SGND and FRGND Connected
Position 2&3 = SGND and FRGND Not Connected
DTE as DSR or RI (JB6 & JB7)
Because the Model 1000RC uses DSR (but not RI), only position
1&2 is valid when this rear card is used with the Model 1000RC.
Position 1&2 causes the terminal (DTE) to see DSR when the Model
1000RC is powered up properly. Position 2&3 is for Ring Indicate,
which is non-functional on the Model 1000RC. Furthermore, use of
position 2&3 will cause DSR to float, which will lead to improper
operation of the Model 1000RC.
Figure 7. Model 1000R16P Rack Chassis with power supply
JB6 & JB7
4.1.1 THE RACK POWER SUPPLY
Position 1&2 = DSR
Position 2&3 = (Ring Indicate) Not Valid for Model 1000RC
The power supply included in the Model 1000R16P rack uses the
same mid-plane architecture as the modem cards. The front card of
the power supply slides in from the front, and the rear card slides in
from the rear. They plug into one another in the middle of the rack.
The front card is then secured by thumb screws and the rear card by
conventional metal screws.
WARNING! There are no user-serviceable parts in the
power supply section of the Model 1000RC. Voltage
setting changes and fuse replacement should only be
performed by qualified service personnel. Contact Patton
Electronics Technical support at (301)975-1007 for more
information.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the Power Supply On and Off
The Model 1000RC is wired as a DCE (Data Communications
Equipment). Therefore, it wants to connect to a DTE (Data Termination
Equipment). If your RS-232 output device is a DTE, you may need to
use a special cable (such as a DB-25 to modular cable). If your
RS-232 output device is DCE, you will require a null modem
connection. Call Patton Technical Support at (301) 975-1007 for
specific installation instructions.
The power switch is located on the front panel. When plugged in
and switched on, a red front panel LED will glow. Since the Model
1000R16P is a “hot swappable” rack, it is not necessary for any cards
to be installed before switching on the power supply. The power supply
may be switched off at any time without harming the installed cards.
4.4 TWISTED PAIR CONNECTION
4.2 INSTALLING THE MODEL 1000RC INTO THE CHASSIS
The Model 1000RC operates full duplex over two twisted pair.
In all applications, the twisted pair wire must be 26 AWG or thicker,
unconditioned, dry, metallic wire. Both shielded and unshielded wire
are satisfactory. Note: The Model 1000RC can only be installed on
private twisted pair cable. Dial-up analog circuits, such as those used
with a standard Hayes-type modem, are not acceptable. For further
information about acceptable wire grades, please refer to the diagrams
in Appendix B.
The Model 1000RC is comprised of a front card and a rear card.
The two cards meet inside the rack chassis and plug into each other by
way of mating 50 pin card edge connectors. Use the following steps as
a guideline for installing each Model 1000RC into the Model 1000R16P
rack chassis:
1. Slide the rear card into the back of the chassis along the metal
rails.
2. Secure the rear card using the metal screws provided.
Notice! Any modular twisted pair cable connected to
the Model 1000RC must be shielded cable, and the outer
shield must be properly terminated to a shielded modular
plug on both ends of the cable.
3. Slide the front card into the front of the chassis. It should meet the
rear card when it's almost all the way into the chassis.
4. Push the front card gently into the card-edge receptacle of the rear
card. It should “click” into place.
4.4.1 POINT-TO-POINT TWISTED PAIR CONNECTION
5. Secure the front card using the thumb screws.
The 6-position RJ-11 and 8-position RJ-45 jack options for the
Model 1000RC–always the upper jack on the rear interface card–are
prewired for a standard TELCO wiring environment (See Appendix D
for pin number orientations). Connection of a 4-wire twisted pair circuit
between two or more Model 1000RCs requires a crossover cable as
shown in the following charts.
Note: Since the Model 1000R16P chassis allows “hot swapping”
of cards, it is not necessary to power down the rack when you
install or remove a Model 1000RC.
4.3 RS-232 CONNECTION
RJ-11 Cable
The RS-232 ports are always the lower ports on the interface card.
The 10-pin RJ-45 is pinned according Patton's Modified Modular
Interface Standard (based on the EIA/TIA-561Standard). For specific
interface pin-outs, please refer to the diagrams in Appendix D.
SIGNAL
PIN#
PIN#
SIGNAL
GND†
RCV-
XMT+
XMT-
RCV+
GND†
1-----------------------6
2-----------------------4
3-----------------------5
4-----------------------2
5-----------------------3
6-----------------------1
GND†
XMT-
RCV+
RCV-
XMT+
GND†
Notice! Any terminal cable connected to the Model
1000RC must be shielded cable, and the outer shield must
be 360 degree bonded–at both ends–to a metal or
metalized backshell.
(continued)
10
(continued)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 OPERATION
RJ-45 Cable
PIN#
Once you have configured each Model 1000RC and connected the
cables, you are ready to operate the units. Section 5.0 describes the LED
status monitors and the power-up procedure.
SIGNAL
PIN#
SIGNAL
GND†
RCV-
XMT+
XMT-
RCV+
GND†
2-----------------------7
3-----------------------5
4-----------------------6
5-----------------------3
6-----------------------4
7-----------------------2
GND†
XMT-
RCV+
RCV-
XMT+
GND†
5.1 LED STATUS MONITORS
The Model 1000RC features thirteen front panel LEDs that indicate
the condition of the modem and communication link. Figure 9 shows the
positions of the LEDs and the bullets describe their functions.
†Connection to ground is optional
Model 1000RC
Power
TD
Unit
A
RD
CD
TD
RD
CD
Unit
B
Figure 9. The Model 1000RC front panel, showing LED positions
• The green “PWR” LED glows when power is being applied to the
modem card through its mid-plane chassis connection.
• The “TD” and “RD” indicators blink red and green to show data
activity. A solid red light indicates an idle state. Solid green is an
“illegal” condition and typically indicates a problem in the system.
• If your carrier detect strap is configured as “Always On”, the “CD”
light will always be green. If the carrier detect strap is set to
“Normal”, the green LED lights when the receive carrier is detected;
the red LED lights when the receive carrier is absent.
5.2 POWER-UP
There is no power switch on the Model 1000RC: Power is
automatically applied to the 1000RC when its card-edge connector
touches the chassis’ mid-plane socket, or when the chassis’ power is
turned on. Note: The 1000RC is a “hot swappable” card—it will not be
damaged by plugging it in or removing it while the rack is powered up.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
SPECIFICATIONS
APPENDIX B
CABLE RECOMMENDATIONS
The Patton Model 1000RC operates at frequencies of 20kHz or less
and has been performance tested by Patton technicians using twisted-
pair cable with the following characteristics:
Transmission Format: Asynchronous
Data Rate: 0 to 19.2 Kbps
Wire Gauge
Capacitance
Resistance
Surge Protection: 600W power dissipation at 1 mS
19 AWG
22 AWG
24 AWG
83nf/mi or 15.72 pf/ft.
83nf/mi or 15.72 pf/ft.
83nf/mi or 15.72 pf/ft.
.0163 Ohms/ft.
.0326 Ohms/ft.
.05165 Ohms/ft.
Control Signal: DCE Mode: CTS (Pin 8) turns ON immediately after
the terminal raises RTS (Pin 9); DSR (Pin 2) turn ON immediately
after the rack has power; CD (Pin 3) may be constantly “ON” or
“normal” (i.e. follows presence or absence of RXC signal).
To gain optimum performance from the Model 1000RC, please keep
the following guidelines in mind:
Transmission Line: 4-wire, unconditioned twisted pair, shielded or
unshielded
• Always use twisted pair wire—this is not an option.
Transmit Mode: Full duplex, 4-wire
Line Connection: RJ-11 or RJ-45 jack
Temperature Range: 1-50°C (34-122°F)
Altitude: 0-15,000 feet
• Use twisted pair wire with a capacitance of 20pf/ft or less.
• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher
AWG numbers than 26)
• Use of twisted pair with a resistance greater than the above
specifications may cause a reduction in maximum distance
obtainable. Functionality should not be affected.
Humidity: Up to 95% non-condensing
Dimensions: 0.95”w x 3.1”h x 5.4”l
• Many environmental factors can affect the maximum distances
obtainable at a particular site. Use the above data rate/distance
table as a general guideline only.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C
FACTORY REPLACEMENT PARTS
APPENDIX D
INTERFACE SETTINGS & ORIENTATION
The Patton Model 1000RC rack system features interchangeable
rear half cards, power cords/fuses for international various operating
environments and other user-replaceable parts. Model numbers and
descriptions for these parts are listed below:
PATTON MODULAR INTERFACE - 10 Wire RJ-45
Contact Number
Circuit
Description
1
2
N/A
Not Used
DSR
Patton Model #
Description
125
1000RPEM..........................120/240V Rear Power Entry Module
1000RPSM-1.......................120/240V Front Power Supply Module
1000RPEM-DC ...................DC Rear Power Entry Module
1000RPSM-48A ..................48V Front Power Supply Module
3
109
Received Line Signal Indicator (CD)
DTE Ready (DTR)
4
108 / 2
102
5
Signal Common
6
104
Received Data
0805US ...............................American Power Cord
0805EUR.............................European Power Cord CEE 7
0805EURP ..........................Europlug Power Cord CEE 7/16
0805UK ...............................United Kingdom Power Cord
0805AUS.............................Australia/New Zealand Power Cord
0805DEN.............................Denmark Power Cord
0805FR ...............................France/Belgium Power Cord
0805IN.................................India Power Cord
7
103
Transmitted Data
8
106
Clear to Send
9
105 / 133
N/A
Request to Send / Ready for Receiving
Not Used
10
Pins 2-9 conform to the EIA/TIA-561 eight position non-synchronous interface standard.
0805IS.................................Israel Power Cord
0805JAP..............................Japan Power Cord
0805SW ..............................Switzerland Power Cord
0516FPB1 ...........................Single Width Blank Front Panel
0516FPB4 ...........................4-Wide Blank Front Panel
0516RPB1...........................Single Width Blank Rear Panel
0516RPB4...........................4-Wide Blank Rear Panel
056S1..................................Set of 16 #4 pan head screws/washers
For all modular jacks
(6, 8 or 10 position):
Pin 1 is always toward
the bottom when the
rear card is oriented
correctly in the slot
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|