Operating and installation instructions
Ceramic hobs with induction
KM 6113 / KM 6112 / KM 6115
KM 6116 / KM 6117 / KM 6118
en - GB
To avoid the risk of accidents or
damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 07 798 970
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Safety lock / System lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Safety switch-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Safety instructions for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
KM 6112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
KM 6113. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
KM 6115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
KM 6116. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
KM 6117. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
KM 6118. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Installing the hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
After sales service, data plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Models
KM 6113
a
Cooking zone with TwinBooster
bc Cooking zones with Booster
d
Control panel
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
KM 6112 / KM 6115 / KM 6116
a
Cooking zone with TwinBooster
bcd Cooking zones with Booster
Control panel
e
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
KM 6117
ac Cooking zone with TwinBooster
bd Cooking zones with Booster
e
Control panel
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
KM 6118
a
Cooking zone with TwinBooster
bcd Cooking zones with Booster
e
Control panel
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Control panel
i
j
k
l
e
8 8
g
h
d
8
8.
8
8
f
c
a
b
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Sensor controls
aFor switching the hob on and off
b- For setting the power level
- For activating the lock
- For setting the time
cBooster/TwinBooster
dFor selecting the cooking zone
e- For selecting the timer
- For switching between the timer functions
- For selecting the switch-off time (see "Switching off a cooking zone
automatically")
Indicator lamps
fBooster/TwinBooster
Cooking zone displays
g
0
= Cooking zone ready for use
= Keeping warm function
1 to 9 = Power levels
^
f
= TwinBooster level 1
h
ß
#
F
A
= Booster/TwinBooster level 2
= No pan on cooking zone or pan unsuitable (see "Induction")
= Residual heat
= Fault (see "Safety switch-off")
= Auto heat-up when the power level range has been extended
hIndicator lamp for Auto heat-up or extended power setting (see "Programming"),
e.g. the back right-hand cooking zone
Timer display
i
00 to 99 = Time in minutes
0.^ to 9.^ = Time in hours
jIndicator lamp for relevant zone, e.g. back right-hand cooking zone
kIndicator lamp for minute minder
lIndicator light for half hours with a minute minder time of more than 99 minutes
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Cooking zones
Cooking
KM 6113
Rating in watts for 230 V**
zone
Minimum to maximum
C in cm*
f
18 - 28
Normal
2600
3000
3700
TwinBooster level 1
TwinBooster level 2
x
z
14 - 20
10 - 16
Normal
Booster
1850
3000
Normal
Booster
1400
2200
Total:
7400
Cooking
zone
KM 6112 / KM 6115 / KM 6116 / KM 6118
Minimum to maximum Rating in watts for 230 V**
C in cm*
y
16 - 23
Normal
2300
3000
3700
TwinBooster level 1
TwinBooster level 2
w
x
z
10 - 16
14 - 20
14 - 20
Normal
Booster
1400
2200
Normal
Booster
1850
3000
Normal
Booster
1850
3000
Total:
7400
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Cooking
zone
KM 6117
Rating in watts for 230 V**
Minimum to maximum
C in cm*
y
16 - 23
Normal
2300
3000
3700
TwinBooster level 1
TwinBooster level 2
w
x
10 - 16
Normal
Booster
1400
2200
14 - 20 /
Normal
1850
2500
3000
2300
3000
3700
TwinBooster level 1
TwinBooster level 2
Normal
20 x 30
14 - 20
TwinBooster level 1
TwinBooster level 2
z
Normal
Booster
1850
3000
Total:
7400
* Pans of any diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct application
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal injury
and damage to property.
This hob is not designed for
~
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
– Shops
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before installation and before using
it for the first time. They contain
important notes on installation,
safety, use and maintenance.
– Offices and showrooms
and by residents in establishments
such as:
– Hostels and guest houses.
The appliance is intended for
~
domestic use only to cook food and
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.
keep it warm.
Any other use is not supported by the
manufacturer and could be dangerous.
Miele cannot be held liable for damage
resulting from incorrect or improper use
or operation.
This hob is not intended for outdoor
~
use.
This appliance is not intended for
~
use by people with reduced physical,
sensory or mental capabilities, or lack
of experience and knowledge, unless
they are supervised whilst using it, or
have been shown how to use it by a
person responsible for their safety.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Safety with children
Packaging, e.g. cling film,
~
polystyrene and plastic wrappings,
must be kept out of the reach of babies
and young children. Danger of
Use the safety lock to prevent
~
children operating the appliance or
altering the settings.
suffocation. Dispose of or recycle all
packaging safely as soon as possible.
Keep children away from the
~
appliance at all times. It is not a toy! To
avoid the risk of injury, do not allow
them to play with it or use the controls.
They will not understand the potential
dangers posed by it. They should be
supervised whenever you are working
in the kitchen.
Older children may use the
~
appliance only when its operation has
been clearly explained to them and
they are able to use it safely,
recognising the dangers of misuse.
The appliance gets hot when in use
~
and remains hot for quite a while after
being switched off. To safeguard
against burning, keep children well
away from the appliance at all times.
Do not store anything which might
~
arouse a child's interest in storage
areas above or next to the hob.
Otherwise they could be tempted into
climbing onto the appliance with the
risk of burning themselves.
Keep all pans out of reach of
~
children. Turn pan handles inwards
away from the edge of the hob. Danger
of burning or scalding. Special hob
guards are available from good retail
outlets.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Installation, maintenance and
~
repairs may only be carried out by a
Before installation, check the
~
suitably qualified and competent
person in strict accordance with current
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. Miele
cannot be held liable for unauthorised
work.
appliance for visible signs of damage.
Do not install and use a damaged
appliance. It could be dangerous.
The electrical safety of this
~
appliance can only be guaranteed if
correctly earthed. It is most important
that this basic safety requirement is
observed and regularly tested, and
where there is any doubt, the electrical
system in the house should be
During installation, maintenance and
~
repair work, the appliance must be
disconnected from the mains electricity
supply.
inspected by a qualified electrician.
Miele cannot be held liable for the
consequences of an inadequate
earthing system (e.g. electric shock).
Ensure that power is not supplied to the
appliance until after it has been
installed or until after any maintenance
or repair work has been carried out.
Before connecting the appliance,
~
If the hob is fitted with a
~
make sure that the connection data on
the data plate (voltage and frequency)
match the mains electricity supply.
This data must correspond in order to
avoid the risk of damage to the
appliance. Consult a qualified
communication module, in addition to
disconnecting the hob, this module
must also be disconnected from the
mains electricity during installation and
maintenance of the hob as well as while
any repair work is being carried out.
Ensure that power is not supplied to the
hob or the communication module until
electrician if in any doubt.
For safety reasons, this appliance
~
may only be used after it has been built the hob has been installed or until after
in.
any maintenance or repair work has
been carried out.
Do not open the casing of the
~
appliance.
Tampering with electrical connections
While the appliance is under
~
guarantee, repairs should only be
or components and mechanical parts is undertaken by a service technician
highly dangerous to the user and can
cause operational faults.
authorised by Miele. Otherwise the
guarantee is invalidated.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Faulty components must only be
~
replaced by genuine Miele original
Correct use
For people fitted with a heart
~
pacemaker:
spare parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
Please note that the area immediately
surrounding the hob is
electromagnetically charged. It is
If the connection cable is damaged, unlikely to affect a pacemaker.
~
it must be replaced by a suitably
However, if in any doubt, consult the
manufacturer of the pacemaker or your
doctor.
qualified electrician with a specialist
connection cable of type H 05 V V-F
(pvc insulated), available from Miele.
To prevent damage to items which
~
are susceptible to magnetic fields, e.g.
Do not connect the appliance to the
~
mains electricity supply by a
credit cards, diskettes, pocket
multi-socket adapter or an extension
lead. These do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
calculators etc, do not leave them in the
immediate vicinity of the hob.
The appliance gets hot when in use
~
and remains hot for quite a while after
being switched off. There is a danger of
burning until the residual heat
indicators go out.
Do not use the hob if it is faulty, or if
~
the ceramic surface is cracked,
chipped or damaged in any way.
Switch it off immediately, and
Do not leave the appliance
~
disconnect it from the mains electricity
supply. Danger of electric shock.
unattended whilst it is in use.
Pans that have boiled dry can cause
damage to the ceramic surface for
which Miele cannot be held liable.
Boiling fat or oil could ignite and cause
a fire.
In areas which may be subject to
~
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage caused by
cockroaches or other vermin will not be
covered by the guarantee.
If oil or fat does catch fire, do not
~
attempt to put out the flames with water.
Use a suitable fire blanket, saucepan
lid, damp towel or similar to smother the
flames.
Use heat-resistant pot holders or
~
gloves when using the appliance. Do
not let them get damp or wet, as this
causes heat to transfer through the
material more quickly with the risk of
scalding or burning yourself.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Do not flambé under a cooker hood.
~
The flames could set the cooker hood
Never heat an empty pan unless the
~
manufacturer of the pan expressly
on fire.
states that you can do so. Because
induction heating works extremely
quickly the base of the pan could heat
up to the temperature at which oil or fat
self-ignites within a very short time.
Do not use the appliance as a
~
resting place for anything else.
Take particular care never to place
cutlery or other metal objects on the
appliance. When the appliance is
switched on either deliberately or by
mistake, or when there is residual heat
present, there is the risk of metal
objects heating up, with a danger of
burning.
Keep the hob clean. Grains of salt,
~
sugar and sand (e.g. from cleaning
vegetables) can cause scratches.
Never place hot pans on the area
~
around the controls. The electronic unit
underneath could get damaged.
Depending on the material, other
objects left on the hob could also melt
or catch fire.
Do not drop anything on the ceramic
~
surface. Even a light object could
cause damage in certain
circumstances.
Damp pan lids might adhere to the
ceramic surface and be difficult to
dislodge.
Do not allow either solid or liquid
~
sugar, or pieces of plastic or aluminium
Switch the cooking zones off after use.
Do not cover the appliance, e.g.
foil to get onto the cooking zones when
~
with a cloth, kitchen foil, etc. This could they are hot. If this should occur, switch
be a fire hazard if the appliance is
switched on by mistake.
off the appliance, and carefully scrape
off all the sugar, plastic or aluminium
residues from the hob whilst they are
still hot, using a shielded scraper
blade.
Do not use plastic or aluminium foil
~
containers. These melt at high
temperatures and could catch fire.
Take care not to burn yourself.
If residues are allowed to cool before
being removed, the ceramic surface
Do not heat up unopened tins of
~
food on the hob, as pressure will build
up in the tin, causing it to explode. This would be susceptible to pitting or even
could result in injury and scalding or
damage.
cracking.
Clean the appliance once it has cooled
down.
Do not use pots and pans on the
~
ceramic hob with bases with
pronounced edges or ridges, e.g. cast
iron pans. These could scratch or scour
the hob surface permanently.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
When using an electrical appliance,
Do not use two pans on a
~ ~
e.g. a hand-held food blender, near the cooking/extended zone at the same
appliance, ensure that the cable of the
electrical appliance cannot come into
contact with the hot appliance. The
insulation on the cable could become
damaged, giving rise to an electric
shock hazard.
time.
If the appliance is installed behind a
~
kitchen furniture door, it may only be
used with the furniture door open.
Do not close the door whilst the hob in
use or whilst there is any residual heat
left in the appliance.
This appliance is fitted with a
~
cooling fan. If a drawer is fitted directly
underneath the hob, ensure that there
is sufficient space between the drawer
and its contents and the underside of
the appliance in order to ensure
If the appliance is installed behind a
~
kitchen furniture door, it may only be
used with the furniture door open.
Only close the door when the appliance
is switched off and the residual heat
indicators have gone out.
sufficient ventilation for the hob. Do not
store pointed or small items or paper in
the drawer. They could get in through
the ventilation slots or be sucked into
the housing by the fan and damage the
fan or impair cooling.
Miele cannot be held liable for
damage caused by non-compliance
with these Warning and Safety
instructions.
Spray canisters, aerosols and other
~
inflammable substances should not be
stored in a drawer under the hob.
Cutlery inserts must be heat-resistant.
Metal utensils stored in a drawer
~
under the hob can become hot if the
induction hob is used intensively for a
long time.
Always ensure that food is
~
sufficiently cooked or reheated. Some
foods may contain micro-organisms
which are only destroyed by thorough
cooking at a sufficiently high
temperature for long enough.
Therefore, when cooking or reheating
food such as poultry, it is particularly
important that the food is completely
cooked through. If in doubt, select a
longer cooking or reheating time.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Please dispose of it at your local
community waste collection/recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Please stick the extra data plate for the appliance supplied
with this documentation in the space provided in the "After
sales service, data plate" section of this booklet.
Cleaning for the first time
^ Remove any protective wrapping and adhesive labels.
^ Before using for the first time, clean the appliance with a
damp cloth only and then wipe dry.
Before using for the first time
On hobs with bevelled glass edges, a small gap may be
visible between the hob and the worktop during the first
few days after installation. This gap will reduce with time as
the appliance is used and will not affect the electrical
safety of your appliance.
When the appliance is used for the first time, it may give off a
slight smell and some vapours. This smell will be less
noticeable with each subsequent use before dissipating
completely.
The smell and any vapours given off do not indicate a faulty
connection or appliance and they are not hazardous to
health.
Please note that the heating up time on induction hobs is
very much shorter than on conventional hobs.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Induction
The induction principle
An induction coil is located under each cooking zone. When
a cooking zone is switched on, this coil creates a magnetic
field which impacts directly on the base of the pan and heats
it up. The cooking zone itself is heated up indirectly by the
heat given off by the pan.
An induction cooking zone only works when a ferromagnetic
pan is placed on it (see "Pans").
Induction automatically recognises the size of the pan, i.e.
heat is only generated in the area covered by the base of the
pan.
The cooking zone will not work:
– if it is switched on without a pan in place, or if the pan is
unsuitable (non-magnetic base).
– if the diameter of the base of the pan is too small.
– if the pan is taken off the cooking zone when it is switched
on.
If this happens, ß will flash in the relevent cooking zone
display alternating with the power setting selected. After a
while, the ß will light up continuously on its own.
If a suitable pan is placed on the cooking zone within
3 minutes, the ß will go out and you can continue as normal.
If no pan or an unsuitable pan is placed on the cooking zone,
the cooking zone and the hob will switch off automatically
after 3 minutes.
Take particular care never to place cutlery or other metal
objects on the hob. When the appliance is switched on
either deliberately or by mistake, or when there is residual
heat present, there is the risk of metal items heating up
with the danger of burning.
Switch the cooking zones off after use.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Induction
Noises
When using an induction cooking zone, the following noises
can occur in the pan, depending on what it is made of and
how it has been constructed.
– On the higher power settings, it might buzz. This will
decrease or cease altogether when the power setting is
reduced.
– If the pan base is made of layers of different materials (e.g.
in a sandwiched base), it might emit a cracking sound.
– Whistling might occur if linked zones (see "Booster
function") are being used at the same time, and the pans
also have bases made of layers of different materials.
– You might hear a clicking sound from the electronic
switches, especially on lower settings.
The appliance has a cooling fan to help extend the life of the
electronics. When the hob is being used intensively, this will
come on and you will hear a whirring sound. The fan may
continue to run after the appliance has been switched off.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Induction
Pans
Suitable pans include:
– stainless steel pans with a magnetic base
– enamelled steel pans
– cast iron pans
Unsuitable pans:
– stainless steel pans without a magnetic base
– aluminium and copper pans
– glass, ceramic or earthenware pots and pans
To test whether a pot or pan is suitable for use on an
induction hob, hold a magnet to the base of the pan. If the
magnet sticks, the pan is suitable.
Please be aware that the properties of the pan base can
affect the eveness with which food heats up in the pan.
To make optimum use of the cooking zones, choose pans
with diameters larger than the innermost markings but smaller
than the outermost markings. If the diameter of the pan is
smaller than the innermost marking, the induction heating will
not work. The zone will behave as if it had no pan on it.
Please note that the maximum diameter quoted by
manufacturers often refers to the diameter of the top rim of
the pot or pan. The diameter of the base (generally smaller) is
more important.
Make sure that pans are placed centrally on the cooking
zone.
If a pan is placed only partially on a zone, there is a risk
that the handle could get very hot.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
How the hob is operated
The hob is equipped with electronic sensor controls which
react to finger contact.
To operate the hob, touch the relevant sensor. Each time you
touch a sensor, an audible tone sounds.
In order to set or alter a power level or the time, the cooking
zones and the timer must be "active".
To activate a cooking zone or the timer, touch the sensor for
selecting the relevant cooking zone or the timer. After you
have touched the sensor, the relevant cooking zone or timer
display will start to flash. The cooking zone or the timer is
"active" whilst the display is flashing and you can set a power
level or time.
Exception:
If only one of the cooking zones is in operation, you can alter
the power level without activating the cooking zone.
Take care to keep the control panel clean and do not
place anything on top of it. The sensors may fail to react or
they could mistake the article or any dirt for a fingertip
contact, thereby activating a function or even causing the
hob to switch off automatically (see "Safety switch-off".)
Never place hot pans on the sensors. The electronic unit
underneath could get damaged.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Switching on
The hob must be switched on before any of the zones can be
used.
Do not leave the appliance unattended whilst it is being
used.
To switch the hob on
^ Touch the s sensor.
0 will appear in each of the cooking zone displays. 00 will
appear in the timer display. If no further entry is made, the
hob will switch itself off after a few seconds for safety
reasons.
Switching on a cooking zone, setting a power level
^ Touch the sensor for selecting the cooking zone you want.
A 0 will flash in the cooking zone display.
^ Whilst the 0 is flashing, select a power level of between 1
and 9 by touching the - or + sensor.
To select cooking with Auto heat-up, press the - sensor
first (see "Auto heat-up"). To select cooking without Auto
heat-up, press the + sensor first.
The power level selected flashes in the display for a few
seconds to start with and then lights up constantly.
Altering the power level
^ Touch the sensor for selecting the cooking zone you want.
The power level will flash.
^ Touch the + or - sensor to set the power level you want.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Settings
The appliance is delivered with 9 power levels programmed in. If you wish to
fine-tune a setting, you can extend the power level range (see "Programming").
The intermediate setting will be represented by an illuminated dot next to the
number.
Settings
Standard
factory settings
(9 power levels) (17 power levels)
Extended
settings
Keeping warm
h
h
Melting butter
1 - 2
1 - 2.
Dissolving gelatine
Making milk puddings
2
3
2 - 2.
3 - 3.
Warming small quantities of liquid
Cooking rice
Defrosting frozen vegetables
Making porridge
3
3
4
2. - 3
2. - 3.
4 - 4.
Warming liquid and semi-solid foods
Making omelettes and lightly frying eggs
Steaming fruit
Cooking dumplings
4
5
5
6
4 - 5.
5
Steaming vegetables and fish
Defrosting and heating frozen food
5 - 5.
5. - 6
Bringing large quantities of food to the boil, e.g. casseroles
Thickening custard and sauces, e.g. hollandaise
Gently frying eggs (without overheating the fat)
6
7
5. - 6.
6. - 7.
Gently braising meat, fish and sausages (without overheating
the fat)
Frying pancakes etc.
Cooking stew
7
8
9
6. -7
8 - 8.
9
Boiling large quantities of water
Bringing to the boil
These settings should only be taken as a guide.
The power of the induction coils will vary depending on the size and material of the pan. For this
reason it is possible that the settings will need to be adjusted slightly to suit your pans. As you use the
hob, you will get to know which settings suit your pans best.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Auto heat-up
When Auto heat-up has been activated, the cooking zone
switches on automatically at the highest power level/setting
and then switches to the continued cooking setting selected.
The heat-up time depends on which continued cooking
setting has been chosen (see chart).
To activate Auto heat-up
^ Touch the sensor for selecting the cooking zone you want.
The cooking zone display will flash.
^ Press the - sensor until the required continued cooking
setting appears, e.g. 6.
During the heat-up time an indicator lamp to the right of the
continued cooking setting will light up, and go out at the end
of it.
In the extended range of power settings (see
"Programming"), A flashes alternately with the continued
cooking setting during the heat-up time.
Altering the continued cooking setting will deactivate auto
heat-up.
To deactivate Auto heat-up
You can switch off Auto heat-up before the Auto heat-up time
has finished.
^ Touch the sensor for selecting the cooking zone you want.
The power level will flash.
^ Select a different power level.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued
Heat-up time
cooking setting*
in minutes and seconds (approx.)
1
1.
2
0 : 15
0 : 15
0 : 15
0 : 15
0 : 25
0 : 25
0 : 50
0 : 50
2 : 00
5 : 50
5 : 50
2 : 50
2 : 50
2 : 50
2 : 50
2 : 50
-
2.
3
3.
4
4.
5
5.
6
6.
7
7.
8
8.
9
* The continued cooking settings with a dot after the number
are only available if the power level range has been
extended (see "Programming").
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Booster function
The cooking zones are equipped with a Booster or
TwinBooster (see "Guide to the appliance").
When activated, the power is boosted for 15 minutes so that
large quantities can be heated quickly, e.g. when boiling
water for cooking pasta.
The Booster function can only be used on two cooking zones
at the same time, one on the left and one on the right.
If the Booster function is switched on when
– no setting has been selected, the cooking zone will revert
automatically to setting 9 at the end of the Booster time or
if the Booster function is switched off before this.
– a setting has been selected, the cooking zone will revert
automatically to the setting selected at the end of the
Booster time or if the Booster function is switched off
before this.
Taking a pan off the zone whilst the Booster is in operation
interrupts the Booster function. It will resume if a pan is
placed back on the zone within 3 minutes.
The extra boost of energy is only available by taking a
proportion of energy away from another cooking zone. For
this reason, the cooking zones are networked in pairs.
Example:
When selecting the Booster/TwinBooster level 1 for a zone,
the following happens within the pairs:
– If Auto heat-up is activated on the other zone within the
pair, this will be switched off.
– If the other zone within the pair is set at power level 9, the
power level on that zone will be reduced.
If TwinBooster level 2 is selected, the other zone within the
networked pair will be switched off.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
To switch on the Booster
^ Touch the sensor for selecting the cooking zone you want.
^ Select a power level if you wish.
^ Touch the B I/II sensor.
The indicator lamp for the Booster lights up, and h starts to
flash in the cooking zone display.
After a few seconds, h will light up constantly and the
indicator lamp will go out.
To switch on the TwinBooster
Level 1
^ Touch the sensor for selecting the cooking zone you want.
^ Select a power level if you wish.
^ Touch the B I/II sensor.
The indicator lamp for the Booster lights up, and f starts to
flash in the cooking zone display. After a few seconds, f will
light up constantly and the indicator lamp will go out.
Level 2
^ Touch the sensor for selecting the cooking zone you want.
^ Select a power level if you wish.
^ Touch the B I/II sensor twice.
The indicator lamp for the Booster lights up, and h starts to
flash in the cooking zone display. After a few seconds, h will
light up constantly and the indicator lamp will go out.
To switch off the Booster/TwinBooster
^ Touch the sensor for selecting the cooking zone you want.
^ Touch the B I/II sensor repeatedly until the indicator lamp
for the Booster goes out and the cooking zone setting
shows in the display.
or
^ Touch the sensor for selecting the cooking zone you want.
^ Select a different power level.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Keeping warm function
Each cooking zone has a keeping warm function ("h"). The "h"
function is in between the "0" setting and the "1"setting .
If the keeping warm function has been activated, the cooking
zone will switch off automatically after a maximum of 2 hours.
This function is for keeping food that has just been cooked
warm, i.e. food that is still hot. It is not for reheating food
that has gone cold.
Useful tips
– Only use pans for keeping food warm. Cover the pan with
a lid.
– You do not have to stir food while it is being kept warm.
– Nutrients are lost when food is cooked, and this continues
when food is kept warm. The longer food is kept warm for,
the greater the loss of nutrients. Try to ensure that food is
kept warm for as short a time as possible.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Switching off and residual heat indicators
Switching off a cooking zone
^ Touch the sensor for selecting the cooking zone you want
twice.
A 0 will flash in the cooking zone display for a few seconds. If
the cooking zone is still hot, the residual heat indicator will
then appear in the display.
Switching off the hob
^ Touch the s sensor.
This switches off all cooking zones. The residual heat
indicator will appear in the display of any cooking zone which
is still hot.
Residual heat indicators
The lines of the residual heat indicator go out one after
another as the cooking zone cools down. The last horizontal
line only goes out when the cooking zone is safe to touch.
Do not touch or place any heat-sensitive objects on the
cooking zones while the residual heat indicators are on.
Danger of burning and fire hazard.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips on saving energy
– Use a pan lid whenever possible to minimise heat loss.
uncovered
covered
– Select a smaller pan when cooking small quantities. A
smaller pan uses less energy than a larger pan with very
little in it.
– Cook with as little water as possible.
– Once food has come to the boil or the pan is hot for frying,
reduce the heat to a lower setting.
– Cooking times are greatly reduced when using a pressure
cooker.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer
The hob must be switched on to use the timer.
The timer can be used for two different functions:
- to set the minute minder
- to set a cooking zone to switch off automatically.
You can select a time from 1 minute (01) to 91/2 hours (9.^). If
a time of more than 99 minutes (99) is set, the time is set in
half-hour steps. The half hour is indicated by a dot after the
number.
Use the - sensor to reduce the time from 9.^ to 00, and the +
sensor to increase the time from 00 to 9.^. The display stops
at 2h and at 99. To continue entering the setting, briefly
remove your finger from the sensor, and then touch it again.
When the set time has elapsed, 00 will appear in the timer
display for a few seconds. An audible tone will sound at the
same time for a few seconds. To turn the audible tone off
before this, touch the m sensor.
Minute minder
To set the minute minder time
^ Touch the m sensor.
00 and the minute minder indicator lamp will flash in the timer
display.
^ Touch the - or + sensor until the time you require appears
in the display, e.g. 15 minutes.
The time set will then count down in minutes. The time
remaining will be shown in the timer display.
To change the minute minder time
^ Touch the m sensor.
^ Touch the - or + sensor to set the time you want.
To delete the minute minder time
^ Touch the m sensor.
^ Touch the - and + sensors at the same time.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer
To switch a cooking zone off automatically
You can set a time at the end of which a cooking zone will
switch off automatically.
All the cooking zones can be programmed at the same time.
If the time programmed is longer than the maximum
operational time allowed, the cooking zone will switch off
after the maximum time allowed (see "Safety switch-off").
^ Select a power level for the cooking zone you require.
^ Touch the m sensor.
00 and the minute minder indicator lamp will flash in the timer
display.
^ Touch the m sensor again.
The minute minder indicator lamp in the timer display will go
out and one of the cooking zone indicator lamps will flash.
^ If several cooking zones are switched on, touch the m
sensor repeatedly until the indicator lamp for the cooking
zone you wish to use this function for, e.g. back right,
flashes.
The indicator lamps for the cooking zones which are switched
on light up clockwise, starting with the front left.
^ Touch the - or + sensor until the time you require appears
in the display, e.g. 15 minutes.
The time set will then count down in minutes. The time
remaining will be shown in the timer display.
If you want to set another cooking zone to switch off
automatically, follow the same steps as described above.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer
If more than one switch-off time is programmed, the shortest
time remaining will show in the display, and the indicator
lamp for that particular cooking zone will flash. All the other
indicator lamps will light up constantly. If you want to check
on the time remaining for another zone, touch the m sensor
repeatedly until the indicator lamp for the zone you require
flashes.
To change the automatic switch-off time
^ Touch the m sensor repeatedly until the indicator lamp you
require flashes.
^ Touch the - or + sensor to set the time you want.
To use both timer functions at the same time
The minute minder and automatic switch-off functions can be
used at the same time.
If you have programmed in one or more switch-off times, and
would like to use the minute minder as well:
Touch the m sensor repeatedly until the minute minder
indicator lamp flashes.
If you are using the minute minder, and would like to
programme in one or more switch-off times as well:
Touch the m sensor repeatedly until the indicator lamp for
the cooking zone you require flashes.
Shortly after the last entry, the timer display will switch to
showing the shortest time remaining.
If you want to see the time remaining for other cooking zones,
touch the m repeatedly until the relevant indicator lamp
flashes.
Starting with the shortest time remaining which is shown in
the display, all cooking zones which are switched on and the
minute minder are selected clockwise.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
Safety lock / System lock
Keep children away from the hob for their own safety. Your
appliance is equipped with a safety lock and a system lock to
prevent the hob and the cooking zones being switched on or
any settings being altered.
The safety lock is set with the hob switched on. When
activated:
– The cooking zone power levels and the timer settings
cannot be changed.
– The cooking zones, the hob and the timer can be switched
off, but once switched off cannot be switched on again.
The system lock is set with the hob switched off. When
activated, the hob cannot be switched on and the timer
cannot be used.
The default setting for activating the system lock is manual.
The system lock can also be set for manual and automatic
activation, in which case it will be activated automatically five
minutes after the hob has been switched off, unless you set it
manually (see "Programming").
If an unavailable sensor is touched whilst the safety lock or
system lock is activated, L will appear in the front left and C in
the front right of the cooking zone display for approximately
3 seconds.
If there is an interruption to the power supply, the safety
lock and the system lock will be deactivated.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
To activate the locks
^ Touch the - and + sensors at the same time until a long
tone sounds.
To deactivate the locks
^ Touch the - and + sensors at the same time until a tone
sounds.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
Safety switch-off
Safety switch-off with an over-long cooking time
If one of the cooking zones is heated for an unusually long
period of time (see chart) and the power level is not altered,
the hob will switch itself off automatically and the relevant
residual heat indicator will light up.
To use the cooking zone again, switch it back on in the usual
way.
Power level*
h
Maximum operating time in hours
2
10
5
1 / 1.
2 / 2.
3 / 3.
4 / 4.
5 / 5.
6 / 6.
7 / 7.
8 / 8.
9
5
4
3
2
2
2
1
* The power levels with a dot after the number are only
available if the power level range has been extended (see
"Programming").
Safety switch-off if the sensors are covered
Your hob will switch off automatically if one or several of the
sensors remain covered for more than about 13 seconds, for
example by finger contact, food boiling over, or by an object
such as an oven glove or a tea towel.
An F will flash in each of the cooking zone displays.
^ Clean the control panel or remove the obstruction.
F will go out. You can now use the hob again.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
Overheating protection
Induction coils/Cooling elements
All the induction coils and the cooling elements for the
electronics are fitted with an overheating protection
mechanism. Before the induction coils or cooling elements
get too hot, the overheating protection mechanism cuts in in
one of the following ways:
Induction coils
– If the booster function is being used, this will be switched
off.
– The power level will be reduced.
– The cooking zone will switch off automatically.
The fault message "FE44" is displayed.
You will be able to use the cooking zones again as usual
when the fault message has gone out.
Cooling elements
– If the booster function is being used, this will be switched
off.
– The power level will be reduced.
– The cooking zones switch off automatically.
The affected cooking zones can only be used again as usual
once the cooling element has cooled down to a safe level.
Overheating can be caused by:
– heating up an empty pan.
– Fats or oils being heated up on the highest power setting.
– There being insufficient ventilation to the underside of the
appliance.
– a hot cooking zone being switched on after a power cut.
If the overheating protection mechanism triggers again,
contact the Service department.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
Control panel
The control panel electronic unit is equipped with overheating
protection. This switches off the hob automatically before the
electronic unit overheats.
The fault code FE37 will appear.
Once the electronic unit has cooled down sufficiently, the
fault code will go out and you can use the hob again.
Overheating can occur if several cooking zones are heated at
a high power level for a long period of time.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
For Miele branded cleaning and conditioning products see
"Optional accessories".
,Do not use a steam cleaning appliance to clean this
appliance. The steam could reach electrical components
and cause a short circuit.
The appliance should be cleaned after each use. Let it cool
down to room temperature before cleaning.
To avoid water marks and limescale deposits, use a soft cloth
to dry surfaces that have been cleaned with water.
To avoid damaging the surface of your appliance, do not
use:
– washing-up liquid,
– cleaning agents containing soda, alkalines, ammonia,
acids or chlorides,
– cleaning agents containing descaling agents,
– stain or rust removers,
– abrasive cleaning agents, e.g. powder cleaners and cream
cleaners,
– solvent-based cleaning agents,
– dishwasher cleaner,
– grill and oven cleaners,
– glass cleaning agents,
– hard, abrasive brushes or sponges, e.g. pot scourers,
brushes or sponges which have been previously used with
abrasive cleaning agents,
– melamine eraser blocks,
– sharp, pointed objects which could damage the seal
between the ceramic surface and the surrounding frame,
and between the frame and the worktop.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Do not use washing-up liquid to clean the ceramic surface.
Washing-up liquid will not remove all soiling and deposits.
It will form an invisible coating which will cause permanent
discolouration of the ceramic surface.
Clean the hob regularly with a suitable ceramic hob
cleaner.
Wipe all coarse soiling off using a damp cloth. Stubborn
soiling may need to be removed with a shielded scraper
blade.
Then clean the hob with Miele ceramic and stainless steel
hob cleaner (see "Optional accessories") applied with kitchen
paper or a clean cloth. Do not apply cleaner whilst the hob is
still hot, as this could result in marking. Please follow the
manufacturer's instructions.
Finally, wipe the hob with a damp cloth, then polish with a
soft, dry cloth. Ensure that all cleaner residues are removed.
Residues can burn onto the hob the next time it is used, and
cause damage to the ceramic surface.
Spots caused by limescale, water and aluminium residues
(spots with a metallic appearance) can be removed using
Miele's ceramic and stainless steel hob cleaner.
Should any sugar, plastic or aluminium foil spill or fall onto
a hot cooking zone while it is in use, first switch off the
appliance. Then carefully scrape off all the sugar, plastic or
aluminium residues from the hob whilst they are still hot,
using a shielded scraper blade. Take care not to burn
yourself.
Allow the appliance to cool down, and then clean as
described above.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional functions
Reset
The hob has a reset function. This allows you to restore all
settings changed using the programming function to their
original factory default settings.
To activate the reset function
^ Switch the hob on.
^ Touch and keep your fingers on the sensors for the front
left-hand and front right-hand cooking zones at the same
time until the indicators for these cooking zones have gone
out (approx. 10 seconds).
It takes approx. 1 minute to reset your hob to the original
settings. The process is completed when the booster
indicator lights up briefly.
Do not switch the hob on again until the reset process is
completed.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional functions
Programming
You can change the default settings of the programme
options (see chart). Several settings can be altered in
succession.
After the programming mode has been called up, P
(Programme), S (Status) and numbers will appear in the
cooking zone displays. These show the current settings.
Once you have left the programming mode, the hob will be
reset automatically. The process is completed when the
booster indicator lights up briefly.
Do not switch the hob on again until the reset process is
completed.
To call up the programming mode
^ With the hob switched off, touch the s and B I/II sensors at
the same time until the relevant indicator lamp flashes.
To set a programme / status setting
^ Hobs with 4 or more cooking zones
Touch the sensor for selecting the front left cooking zone.
^ Hobs with 3 cooking zones
Touch the sensor for selecting the left cooking zone.
^ Touch the + or - sensor to set the required Programme.
^ Touch the sensor for the front right cooking zone.
^ Touch the + or - sensor to set the required Status setting
(see chart).
To save settings
^ Touch the s sensor until all the displays go out.
To not save settings
^ Touch the B I/II sensor until all the displays go out.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional functions
Programme*
Status** Setting
P
0
Demonstration mode and
factory default settings
S
0
Demonstration mode on
(after the hob is switched on, "d"
will appear in the front left
cooking zone display and "E" in
the front right cooking display for
a few seconds).
S
S
S
1
9
0
Demonstration mode off
Factory default settings reinstated
P
2
Power level range
9 power settings
(1, 2, 3 ... to 9)
S
1
17 power settings
(1, 1., 2, 2., 3 ... to 9)
If the Auto heat-up setting is
selected, an A will flash
alternately with the continued
cooking setting in the display.
P
P
P
3
4
5
Induction warning tone
when there is no pan or
the pan is unsuitable
S
S
S
S
S
S
S
S
S
S
0
1
2
3
0
1
2
3
0
1
Off
Quiet
Medium
Loud
Off
Keypad tone when a
sensor is touched
Quiet
Medium
Loud
Off
Audible tone for the timer
Quiet audible tone on for 10
seconds
S
2
Medium audible tone on for 10
seconds
S
3
Loud audible tone on for 10
seconds
*
Programmes not shown here have no allocation.
** The factory default settings are shown in bold.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional functions
Programme*
Status** Setting
P
7
System lock
S
0
Manual activation of the system
lock only
S
1
Manual and automatic activation
of the System lock
P
P
5. Audible tone if a sensor is
S
S
S
S
S
0
1
0
1
2
Off
covered.
On
6. Sensor reaction speed
Slow
Normal
Rapid
*
Programmes not shown here have no allocation.
** The factory default settings are shown in bold.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes, minor faults in the performance of the
appliance, some of which may result from incorrect operation can be put right
without contacting the Service Department.
,Installation work and repairs to electrical appliances should only be carried
out by a suitably qualified person in strict accordance with current local and
national safety regulations. Repairs and other work by unqualified persons
could be dangerous. The manufacturer cannot be held liable for unauthorised
work.
Problem
Possible cause
Remedy
The hob or cooking The mains fuse has tripped. Reset the trip switch in the
zones cannot be
switched on.
mains fuse box (minimum
fuse rating - see data
plate).
There may be a technical
fault.
Disconnect the appliance
from the electricity supply
for approx. 1 minute.
– Switch off at the wall
socket and withdraw the
plug, or switch off at the
isolator.
or
– Disconnect the mains
fuse.
Reset the trip switch in the
mains fuse box, and switch
the appliance back on. If it
still will not switch on,
contact a qualified
electrician or the Miele
Service Department.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
There is a strange
smell or vapours when
a new appliance is
being used.
The smell and any vapours
will dissipate after a short
time. They are not harmful
and do not indicate a faulty
connection or appliance.
The ß symbol lights up There is no pan on the Use a suitable pan (see
in the display of one of cooking zone, or the
"Pans").
the cooking zones.
pan is unsuitable.
After the hob is
The system lock is
activated.
Deactivate the system lock
(see "Safety lock / System
lock").
switched on, "L"
appears in the front left
cooking zone display
and "C" in the front
right cooking display
for a few seconds.
After the hob is
The appliance is in
Deactivate demonstration
mode (see "Programming").
switched on "d"
demonstration mode.
appears in the front left
cooking zone display
and "E" appears in the
front right cooking
zone display for a few
seconds.
The cooking zones do
not heat up.
A cooking zone or the A cooking zone has
whole hob switches off been in use for too
You can use the cooking
zone again by switching it
back on (see "Safety
switch-off").
automatically.
long.
The overheating
protection mechanism
has triggered.
See "Overheating protection".
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The Booster has
deactivated early
automatically.
The overheating
See "Overheating protection".
The cooking zone is
not working in the
usual way at the power
level set.
protection mechanism
has triggered.
Power level 9 is
Operating both zones
automatically reduced at power level 9 would
if you select power
level 9 on two linked
cooking zones or
extended zones at the
same time.
exceed the permitted
maximum power level
for the two zones.
The hob switches off
while it is in use, an F
appears in every
One or more of the
sensors have been
Clean the control panel or
remove the obstruction (see
covered, e.g. by finger "Safety switch-off").
contact, food boiling
cooking zone display
and a tone sounds.
over or by an object
such as an oven glove.
The food in the pan
There is too much food Start cooking at the highest
hardly heats up or does in the pan.
not heat up at all when
the Auto heat-up
power level and then turn
down to a lower one manually
later on.
function is switched
The pan is not
on.
conducting heat
properly.
The cooling fan
The fan will continue
running until the
continues to run even
after the appliance has appliance has cooled
been switched off.
down. It will then
switch itself off
automatically.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The sensors are
over-sensitive or do
not react at all.
The sensitivity level of the Make sure that there is no
sensors has changed.
direct light (from the sun or
from an artificial source)
falling onto the hob and that
the surrounding area is not
too dark.
An F lights up in the
rear left cooking zone
display and an E lights
up in the rear right
cooking zone display
and numbers appear
in the displays at the
front.
Make sure that there is
nothing covering the sensors
or the hob. Take any pans off
the hob and wipe away any
food deposits.
Interrupt the power supply to
the hob for approx. 1 minute.
left
9
right
0
1
A calibration fault has
occurred after the reset
function has been
If this does not solve the
problem, please call the
Miele Service department.
9
9
2
3
activated or after an
interruption to the power
supply. If the displays do
not go out after 5 minutes,
proceed as described
under "Remedy" on the
right.
9
3
7
The overheating
You can use the hob again
protection mechanism has as soon as the fault code
triggered. goes out (see "Overheating
protection").
The fan is either blocked Make sure it has not been
4
4
4
4
7
or faulty.
blocked by something like a
fork. Remove the cause of
the blockage. If the fault
message appears again, call
the Miele Service
8
Department.
There is an electronic
fault.
Interrupt the power supply to
the hob for approx. 1 minute.
If the problem persists after
reconnecting the appliance
to the power supply, please
contact the Miele Service
department.
All other fault codes
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional accessories
Miele offer a comprehensive range of useful accessories as
well as cleaning and conditioning products for your
appliance.
These products can be ordered online:
or from Miele (see back cover for contact details)
Saucepans and frying pans
Miele offer a wide range of saucepans and frying pans which
are perfect for Miele hobs. Please refer to the Miele website
for more details on individual products.
Pans in various sizes
Frying pan with lid
Anti-stick pans
Wok
Gourmet oven dish
Cleaning products
Ceramic and stainless steel hob cleaner
250 ml
Removes heavy soiling, limescale deposits and aluminium
residues.
E-cloth (microfibre cloth)
Removes finger marks and light soiling.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
After installing the hob, ensure that
~
the connection cable cannot come into
The appliance must only be installed
and connected to the electricity
supply by a suitably qualified and
competent person in strict
contact with the underside of the
appliance. Make sure that there is no
mechanical obstruction, such as a
drawer, which could damage it.
accordance with current national
and local safety regulations.
Observe carefully the safety
~
distances given on the following pages.
Fit the wall units and extractor hood
before fitting the hob to avoid
damaging the appliance.
All dimensions in this instruction booklet
are given in mm.
The veneer or laminate coatings of
~
worktops (or adjacent kitchen units)
must be treated with 100 °C
heat-resistant adhesive which will not
dissolve or distort.
Any backmoulds must be of
heat-resistant material.
This appliance must not be used in
~
a non-stationary location (e.g. on a
ship).
The hob may not be built in over a
~
fridge, fridge-freezer, freezer,
dishwasher, washing machine or
tumble dryer.
This hob must not be installed
~
above ovens or cookers unless these
have a built-in cooling down fan.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distance above the appliance
When two or more appliances are
installed together below a cooker
hood, e.g. a gas wok and a ceramic
hob, which have different safety
distances given in the installation
instructions, you should select the
greater distance of the two.
A minimum safety distance must be
maintained between the appliance and
the cooker hood above it. See the
cooker hood manufacturer’s operating
and installation instructions for details.
If the manufacturer’s instructions are
not available for the cooker hood, a
minimum safety distance of at least
760 mm must be maintained. For any
flammable objects, e.g. utensil rails,
wall units etc. a minimum distance of at
least 760 mm must be maintained
between them and the appliance
below.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distances to the sides and
back of the hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear and a tall unit
or wall on one side (right or left) (see
illustrations).
Not allowed
aMinimum distance of 50 mm
between the back of the worktop
cut-out and the rear edge of the
worktop.
bMinimum distance of 50 mm
between the right of the worktop
cut-out and the nearest piece of
furniture (e.g. tall unit) or a wall.
cMinimum distance of 50 mm
between the left of the worktop
cut-out and the nearest piece of
furniture (e.g. tall unit) or a wall.
Recommended
Not recommended
Not recommended
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distances underneath the hob Interim shelf
To ensure sufficient ventilation to the
hob, a minimum gap must be left
between the underside of the hob and
any oven, interim shelf or drawer.
It is not necessary to fit an interim shelf
underneath the hob, but one may be
fitted if you wish.
A ventilation gap of 10 mm at the back
of the hob is necessary to
The minimum gap between the
underside of the hob and
accommodate the cabling.
We recommend a ventilation gap at the
front of the hob of 20 mm to ensure
– the top of an oven is 15 mm.
– the top of an interim shelf is 15 mm. good ventilation.
– the base of a drawer must be
75 mm.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distance when installing the appliance near a wall with additional
niche cladding
A minimum safety distance must be maintained between the worktop cut-out and
any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e. g. wood) a
minimum safety distance e of 50 mm must be maintained between the cut-out
and the cladding.
If the niche cladding is made from a non-combustible material (e. g. metal,
natural stone, ceramic tiles) a minimum safety distance e of 50 mm less the
thickness of the cladding must be maintained between the cut-out and the
cladding.
Example: 15 mm niche cladding
50 mm - 15 mm = minimum safety distance of 35 mm
Flush-fitted hobs
Hob with frame or bevelled edges
aMasonry
bNiche cladding
Dimension x = thickness of niche cladding material
cWorktop
dWorktop cut-out
eMinimum safety distance
for combustible materials is 50 mm
for non-combustible materials is 50 mm less dimension x
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Hob with frame or bevelled
Tiled worktop
edges
Seal between the hob and the
worktop
Grout lines a and the hatched area
underneath the hob frame must be
smooth and even. If they are not the
hob will not sit flush with the worktop
and the sealing strip underneath the
hob will not provide a good seal
between the hob and the worktop.
The sealing strip under the edge of the
top part of the appliance provides a
sufficient seal for the worktop.
The hob must not be sealed with
sealant (e.g. silicone).
This could result in damage to the
hob or the worktop if the hob ever
needs to be removed for servicing.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Building-in dimensions
KM 6112
aFront
bCasing depth
cMains connection box
The mains connection cable (1440 mm long) is supplied separately.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Building-in dimensions
KM 6113
aFront
bCasing depth
cMains connection box
The mains connection cable (1440 mm long) is supplied separately.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Building-in dimensions
KM 6115
aFront
bCasing depth
cMains connection box
The mains connection cable (1440 mm long) is supplied separately.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Building-in dimensions
KM 6116
aFront
bCasing depth
cMains connection box
The mains connection cable (1440 mm long) is supplied separately.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Building-in dimensions
KM 6117
aFront
bCasing depth
cMains connection box
The mains connection cable (1440 mm long) is supplied separately.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Building-in dimensions
KM 6118
aFront
bCasing depth
cMains connection box
The mains connection cable (1440 mm long) is supplied separately.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the hob
Preparing the worktop
Installing the hob
^ Make the worktop cut-out according
to the dimensions given in the
building-in diagram. Remember to
maintain the minimum safety
distances (see "Safety instructions
for installation").
^ Feed the mains connection cable
down through the cut-out.
^ Place the hob centrally in the cut-out.
When doing this, make sure that the
seal under the hob sits flush with the
worktop on all sides. This is important
to ensure an effective seal all round.
Do not use sealant (e.g. silicone).
^ Seal the cut surfaces on
wood/laminated worktops with a
suitable heat-resistant sealant to
avoid swelling caused by moisture.
If the corners of the frame are not
flush with the worktop surface, the
corner radius (ß R4) can be carefully
scribed to fit.
Make sure that the sealant does not
come into contact with the top of the
worktop.
^ Connect the hob to the mains.
^ Check that the hob works.
No spring clamps are needed to
install the hob. The sealing strip
underneath the hob positions it
securely in the cut-out.
Any gap between the frame and
worktop will reduce with time.
Connecting the mains cable to the
appliance
The mains cable must only be
connected to the appliance by a
qualified and competent electrician
in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
^ Follow the instructions in the wiring
diagram (see "Electrical connection -
Wiring diagram").
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Connection should be made via a
suitable isolator which complies with
national and local safety regulations,
and the On/Off switch should be easily
accessible after the appliance has
been built in.
All electrical work should be carried
out by a suitably qualified and
competent person, in strict
accordance with current local and
national safety regulations (BS 7671
in the UK).
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
For extra safety it is advisable to protect
the appliance with a residual current
device (RCD). Please contact a
unauthorised work.
qualified electrician for advice.
A damaged cable must be replaced
by a suitably qualified electrician
with a special connection cable of
type H 05 VV-F, available from
Miele.
When switched off there must be an
all-pole contact gap of at least 3 mm in
the isolator switch (including switch,
fuses and relays).
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Important U.K.
The appliance is supplied for
connection to a 230-240 V, 50 Hz
supply with a 3-core cable.
The appliance must only be
operated when built-in. This is to
ensure that all electrical parts are
shielded. Live parts must not be
exposed.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
Blue
= neutral
= live
Brown
WARNING
THIS APPLIANCE MUST BE
EARTHED
Please make sure that the connection
data quoted on the data plate match
the household mains supply.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
The electrical safety of this appliance
can only be guaranteed when
Wiring diagram
continuity is complete between it and
an effective earthing system, which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested and where
there is any doubt, the electrical wiring
in the home should be inspected by a
qualified electrician. The manufacturer
cannot be held liable for the
N.B. This appliance is supplied
single phase only in the U.K. / AUS /
NZ
consequences of an inadequate
earthing system such as an electric
shock.
The manufacturer cannot be held
liable for damage which is the direct
or indirect result of incorrect
installation or connection.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service, data plate
In the event of any faults which you cannot remedy yourself, or if the appliance is
under guarantee, please contact:
– Your Miele dealer, or
– the Miele Service Department (see back cover for address).
Please note that telephone calls may be monitored and recorded to improve
our service.
When contacting Miele, please quote the model and serial number of your
appliance. These are given on the data plate.
N.B. A call-out charge will be applied for service visits where the problem
could have been resolved as described in these instructions.
Space in which to stick the extra data plate supplied with the appliance. Ensure
that the model number is the same as the one on the front of these instructions.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / 0811
M.-Nr. 07 798 970 / 05
Download from Www.Somanuals.com. All Manuals Search And Download.
|