SmartNode 5300
Enterprise Session Border Router,
IAD
Quick Start Guide
Important—This is a Class A device and is not intended nor approved for use in an
industrial or residential environment.
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: [email protected]
Part Number: 07MSN5300-QS, Rev. A
Revised: May 21, 2014
Download from Www.Somanuals.com. All Manuals Search And Download.
• Always follow ESD prevention procedures when removing and replac-
ing cards.
• Wear an ESD-preventive wrist strap, ensuring that it makes good skin
contact. Connect the clip to an unpainted surface of the chassis frame
to safely channel unwanted ESD voltages to ground.
WARNING
• To properly guard against ESD damage and shocks, the wrist strap and
cord must operate effectively. If no wrist strap is available, ground
yourself by touching the metal part of the chassis.
1.0 Power Up SmartNode
• 1. Insert the barrel type connector end of the AC power cord into the external power supply connector.
• 2. Insert the female end of the power cord into the internal power supply connector.
• 3. Verify that the AC power cord included with your router is compatible with local standards. If it is not, con-
tact Patton to replace it with a compatible power cord.
• 4. Connect the male end of the power cord to an appropriate power outlet.
• 5. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready to config-
ure.
2.0 Configuring the SmartNode
Refer to the following manuals (available online at http://www.patton.com/kb/index.asp?dt=Manu-
als%20(PDF) ) for detailed information about installing, configuring, operating, and troubleshooting
the SmartNode:
3.0 Connection via Console Access
The SmartNode can be connected to a serial terminal over its serial console port, as depicted in figure 1.
The interconnecting cables shall be acceptable for external use and shall be rated for the
proper application with respect to voltage, current, anticipated temperature, flammability,
and mechanical serviceability.
CAUTION
SmartNode 5300 Quick Start Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1. Connecting SmartNode to Laptop via console access
Configuration settings:
• 19200 bps
• 8 bits, no parity
• 1 stop bit
• flow control off
Note See section “Console Port” on page 35 for console port pin-outs.
4
SmartNode 5300 Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
A Customer and Technical Support
Online support: www.patton.com
Telephone support:
• Standard:1(301)975-1007(USA), Monday–Friday: 8:00 am to 5:00 pm EST(1300 to 2200 UTC/GMT)
• Alternate:+41(0)31 985 25 55 (Switzerland), Monday–Friday 9:00 am to 5:00 pm CET(08:00 to16:30 UTC/
GMT)
Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)
B Factory Defualt Settings
Username: administrator
The SmartNode is running as DHCP client and has at the same time a static IP address configured, on port Ether-
net 0 /0:
IP Address (Eth 0/0): DHCP
Network Mask (Eth 0/0): n/a
and
IP Address (Eth 0/0): 192.168.200.10
Network Mask (Eth 0/0): 255.255.255.0
C Compliance
C.1 EMC
• FCC Part 15, Class A
• EN55022, Class A
• EN55024
• EN50581
C.2 Safety
• UL 60950-1/CSA C22.2 N0. 60950-1
SmartNode 5300 Quick Start Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• IEC/EN60950-1 2nd Edition
C.3 PSTN Regulatory
• This device is not intended nor approved for connection to the PSTN
D Radio & TV Interference Statment (FCC Part
15)
This device generates and uses radio frequency energy, and if not installed and used properly-that is, in strict
accordance with the manufacturer?s instructions-may cause interference to radio and television reception. The
device has been tested and found to comply with the limits for a Class A computing device in accordance with
specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from
such interference in a commercial installation. However, there is no guarantee that interference will not occur in
a particular installation. If the device does cause interference to radio or television reception, which can be deter-
mined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the
following measures: moving the computing equipment away from the receiver, re-orienting the receiving
antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment
and receiver are on different branches).
E TEC Declaration of Conformity
Patton Electronics, Inc declares that this device is in compliance with the essential requirements and other rele-
vant provisions of Directive 2004/108/EC relating to electromagnetic compatibility, Directive 2006/95/EC
relating to electrical equipment designed for use within certain voltage limits and Directive 2011/65/EC relating
to RoHS compliance. The Declaration of Conformity may be obtained from Patton Electronics, Inc at www.pat-
ton.com/certifications.
The safety advises in the documentation accompanying the products shall be obeyed. The conformity to the
above directive is indicated by the CE sign on the device.
F Authorized European Representative
D R M Green
European Compliance Services Limited.
Greyfriars Court
Paradise Square
Oxford, OX1 1BE, UK
6
SmartNode 5300 Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
F.1 Copyright statement
Copyright © 2013, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no
liability for errors that may appear in this document.
F.2 Trademarks statement
The term SmartNodeis a trademark of Patton Electronics Company. All other trademarks presented in this doc-
ument are the property of their respective owners.
F.3 Warranty, Trademark, & Compliance Information
For warranty, trademark and compliance information, refer to the CopperLink User Manual located online
SmartNode 5300 Quick Start Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
SmartNode 5300 Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|