GS2 GYM SYSTEM
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
USER’S GUIDE
CLASS H
PART # 7250101
REV.C
1
Version: GS2-101
Revision: 11/01/02
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody GS2 Gym System. Please read these
instructions thoroughly and keep them for future reference.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Tools Required forAssembly
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 5/32”Allen wrench
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
3
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6’
4’
8’
1’
2’
3’
5’
7’
9’
1’
2’
3’
4’
5’
6’
7’
1 Square = 1’ X 1’
Minimum Required Usable Space
Length
Width
Height
= 82 inches (208.5 cm) 6’ 10”
= 71 inches (180.5 cm) 5’11”
= 83 inches (211 cm) 6’ 11”
Dimensions Including LP5 Leg Press (optional)
Length
Width
= 82 inches (208.5 cm) 6’ 10”
= 108 inches (180.5 cm) 9’ 0”
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
QTY
28
1
QTY
KEY
DESCRIPTION
3/8” LOCK NUT
KEY
1
DESCRIPTION
FRAME
PART #
ACU04-1163
PART #
1
ACUDB2E03811000B
ACUDB2E01208000B
ACUDC1250100020B
ACUDC126013020B
ACU04-1171
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
60
61
62
63
64
65
1
2
1/2” LOW HT LOCK NUT
3/8” FLAT WASHER
1/2” FLAT WASHER
3-1/2” CABLE GUARD
3/4” PLASTIC WASHER
3/4 X 4” SHAFT
2
BASE
ACU04-1158
24
2
3
BASE PLATE
ACU02-1060
1
4
BOOM PLATE LEFT
BOOM PLATE RIGHT
PRESSHANDLERIGHT
PRESS HANDLE LEFT
PRESSARM
ACU04-1160
2
1
5
ACU04-1384
4
1
6
ACU04-1383
ACU06-0363
1
1
7
ACU04-1161
ACU05-0322
2
1
3/8 X 3/4” FLANGE SPACER
3/8 X 1-1/16” FLANGE SPACER
3/8 X 1” LG SPACER
3/8 X 1-1/2” LG SPACER
WEIGHT STACK SPACER
WEIGHT STACK CUSHION
5/16 X 2” ROLL PIN
SHAFT COLLAR
8
ACU04-1164
ACU08-0074
8
1
9
PRIMARYPIVOT
SEATADJUST
LEGPEDESTAL
PULLEYPLATE
SEAT/BACK PAD
3/4 X 17” TUBE
4 X 7” ROLLER PAD
72-3/8” GUIDE ROD
LAT BAR
ACU04-1159
ACU08-0073
4
1
10
11
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
31
32
33
ACU04-1162
ACU08-0011
4
1
ACU04-1157
ACU05-0320
2
2
ACU02-1071
ACU04-1165
2
2
ACU07-0135
ACU06-0047
2
1
ACU01-1782
ACU05-0323
2
6
ACU6194601
ACU05-0212
2
2
TAPER/LOCK SPRING PIN
T-HANDLE SPRING PIN
WEIGHT SELECTOR PIN
STAR KNOB 3/8”
ACU01-1783
ACU11-0059
1
1
ACU04-1099
ACU11-0068
1
2
3/4 X 17/1/2” TUBE
HEAD PLATEASSY
LATCABLE
ACU01-2009
ACU11-0060
1
1
ACU10-0204ASY
ACU13-0091-2
ACU13-0019-1
ACU7292501
ACU06-0194
1
1
ADJUSTABLE GLIDE
STARLOCK COLLAR
RH CAP
ACU05-0017
6
1
LOW CABLE
ACU05-0036
2
15
12
1
WEIGHT PLATE
3-1/2”PULLEY
ACU06-0357
2
1/2” RHCAP HOLDER WASHER
SNAP LINK
ACU06-0024
ACU05-0311
3
ANKLE STRAP
CHAIN
ACU12-0041
ACUDI1080080U
ACU04-0622
1
1
LOW ROW BAR
ACU05-0193
1
2
1/2” LOCK NUT
3/8 X 1-3/4” BOLT
3/8 X 2-1/2” BOLT
3/8 X 3” BOLT
ACUDA1E03813416NB
ACUDA1E03821216NB
ACUDA1E03830016NB
ACUDA1E03833416NB
ACUDA1E003883416NB
ACUDA1C01210413NB
ACUDA1E01283413NB
ACUDB2E01212000B
ACU7308601
ACU04-1100
1
1
WEIGHT STACK LABEL
FOOTPLATE
1
9
2
15
2
3/8 X 4” BOLT
3/8 X 3-3/4” BOLT
3/8 X 8-3/4” BOLT
1/2 X 104mm BOLT
1/2 X 8-3/4” BOLT
ACUDA1E03840016NB
ACU04-1344
1
FRAME BRACE
2
1
PRESSARM SPACER
OVALEND CAP
ACU06-0364
2
1
ACU06-0416
66
NOTE: SOMEOFTHEPARTSLISTEDMAYBEPRE-INSTALLED.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
5
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
36
1
3/8 X 4
63
34
3/8 X 2-1/2
28
3/8 X 3-3/4
30
3/8 X 3
29
2
29
3/8 X 3
36
62
3
64
34
34
FIGURE 1
STEP 1:
•
•
•
LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOLTS (30)
and four 3/8” LOCK NUTS (34). See FIGURE 1.
LOOSELY assemble the FOOTPLATE (62) to the lower holes in the FRAME (1) using one 3/8 x 3” BOLT (29) and one
3/8 LOCKNUT (34)
LOOSELY assemble the TOP of FRAME BRACE (64) to the FRAME (1) using two 3/8 x 4” BOLT (63), two 3/8 WASHERS
(36) and two 3/8 LOCKNUTS (34) Assemble BOTTOM of FRAME BRACE (64) to FRAME (2) using one 3/8 x 3” BOLT
(29), one 3/8 x 2-1/2” BOLT (28) three 3/8 WASHERS (36) and one 3/8 LOCKNUT (34)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 2
• CHECK THAT THE HEADPLATE AND WEIGHT PLATES ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3
FIGURE 3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4:
•
Insert two GUIDE RODS (16) into the BASE (2) as
shown on FIGURE 4. (NOTE: If the GS2 SHROUD
OPTION was purchased, place the GUIDE RODS
(16) through the BOTTOM SHROUD BRACKET
(FOUND IN THE SHROUD KIT BOX) into the BASE
(2), as shown in FIGURE 4.
48
16
• (NOTE: Lubricate GUIDE RODS (16) with silicon
or teflon spray available at most hardware stores.)
• Slide the following items in order down each GUIDE
ROD (16), one WEIGHT STACK SPACER (45), and
one WEIGHT STACK CUSHION (46)
HEAD
PLATE
ASSY
• Using EXTREME CARE slide all fifteen
WEIGHT PLATES (22) down the GUIDE RODS (16)
onto the WEIGHT STACK CUSHIONS (46). Make sure
that the keyholes of the WEIGHT PLATES (22) are all
facing the right way.
•
Slide the head plate assembly down GUIDE RODS
(16) onto the weight stack.
46
45
•
Sl
G
5
4
GS2 SHROUD
BRACKET
OPTION ONLY
30
3/8 X 3-3/4
2
FIGURE 4
34
53
16
FIGURE 5
STEP 5:
•
Carefully slide the RIGHT (5) and LEFT (4) BOOM PLATES onto the GUIDE RODS (16 )as shown in FIGURE 5 and loosely
assembly BOOM PLATES (5), (4) to frame (1) using two 3/8 x 3-3/4” BOLTS (30) and two 3/8” LOCK NUT (34)
[CAUTION MUST BE TAKEN NOT TO PULL GUIDE RODS (16) OUT OF BASE (2)]
•
Screw ADJUSTABLE GLIDE (53) approximately 1/2” into FRAME (1) and tighten jam nut securely as shown
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 6
STEP 6:
6
7
•
Using hammer tap one 5/16 X 2” ROLL PIN (47)
thru LEFT PRESS HANDLE (7) until it is flush
with other side of HANDLE as shown in
FIGURE 6
FLUSHSIDE
•
Repeat STEP 6 for the RIGHT PRESS
ARM HANDLE (6)
47
STEP 7:
NOTE:
Place PRESS ARM (8) upside down on floor as shown to complete this step.
•
Place LEFT PRESS HANDLE (7) onto PRESS
ARM (8). Place PRESS ARM SPACER (65) as
shown over 5/6 x 2 ROLL PIN (47), make sure
that the 5/16 X 2” ROLL PIN (47) passes into
the slot located in the plate of the PRESS ARM
(8)
HANDLES (7) MUST BE PLACED TOWARDS INSIDE OF PRESSARM
7
34
36
•
Once in place secure and tighten the LEFT
PRESS HANDLE (7) to PRESS ARM (8)
using one 3/8” WASHER (36) and one
3/8” LOCK NUT (34)
6
•
•
IMPORTANT! Do not overtighten: PRESS
ARM should rotate freely
47
Repeat STEP 7 for the RIGHT PRESS
ARM HANDLE (6)
8
65
FIGURE 7
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
9
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
29
3/8 X 3”
TIGHTEN
20lbs/ft
36
Taper/Lock
Spring Pin
66
49
34
8
9
FIGURE 8
STEP 8:
• Place PRESSARM (8) into PRIMARYPIVOT (9) and securely tighten using two 3/8 X 3” BOLTS (29), four 3/8” FLAT
WASHERS (36) two 3/8” LOCK NUTS (34)
• Insert and tighten two 3/8” TAPER/LOCK SPRING PINS (49) into PRESS HANDLES (6), (7).
• Lock PRESSARMS (6), (7) into place using 3/8” LOCKING SPRING PINS (49)
• Insert one OVAL END CAP (66) into openning of each arm as shown in FIGURE 8
• To disengage LOCKING SPRING PINS (49), pull out and twist 1/4 turn.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
40
1
33 1/2 X 8-3/4”
37
48
SECURELY
TIGHTEN
60
9
FIGURE 9
STEP 9
• SECURELY TIGHTEN ALL FRAME CONNECTION BEFORE PROCEEDING TO NEXT STEP
• SECURELY TIGHTEN top of both SHAFT COLLARS (48) flush to bottom of both BOOM PLATES (4),(5)
• Insert one 3/4 x 4” SHAFT (40) into both 3/4” FLANGE BEARINGS on FRAME (1)
•
Assemble the PRIMARY PIVOT (9) of the PRESS ARM ASSEMBLY to the top of the FRAME (1) using 1/2 X 8-3/4” BOLT (33),
two 1/2” FLAT WASHERS (37) and 1/2” LOCK NUT (60).
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3/8 X 3”
29
36
13
19
10
61
36
22
3/8 X 3”
29
64
52
1
50
FIGURE 10
STEP 10:
•
Apply WEIGHT STACK LABELS (61) to WEIGHTS (22) and HEAD PLATE (19) as shown in FIGURE 10.
Begin with number one at the HEAD PLATE (19) with larger numbers in consecutive order towards bottom of weight stack.
•
•
Securely assemble one SEAT PAD (13) to the SEAT ADJUSTMENT (10) using two 3/8 X 3” BOLTS (29) and two
3/8” WASHERS (36) as shown.
Securely assemble one SEAT PAD (13) to the FRAME (1) using two 3/8 X 3” BOLTS (29) and two 3/8” WASHERS (36)
as shown. The top connection of the FRAME BRACE (64) may have to be loosened and then re-tightened after SEAT
PAD (13) is tighten
•
•
Gently insert SEAT ADJUSTMENT (10) into tube located on FRAME (1)
Securely tighten the SPRING PIN (50) to the FRAME (1) and hand tighten the STAR KNOB (52)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
55
1/2 X 104mm
56
32
1
11
35
FIGURE 11
STEP 11:
• Assemble the LEG PEDESTAL (11) to the FRAME (1) using one 1/2 X 104mm BOLT (32), two RH WASHERS (56)
and one 1/2” LOW HT LOCK NUT (35)
•
Assemble two RH CAPS (55) to the 1/2” RH WASHERS (56) as shown in FIGURE 11
20
21
FIGURE 12
STEP 12:
Route LAT CABLE (20) and LOW CABLE (21) as shown in FIGURE 12
•
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATION A
•
ILLUSTRATION “A” used as cable routing reference for steps 13-16
NOTE: IF YOU PURCHASEDALEG PRESS, PLEASE REFER TO THE
CABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEG
PRESS KIT
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3/8 X 3-3/4”
30
42
1
24
31
3/8 X 8-3/4”
36
34
44
9
FIGURE 13
STEP 13:
•
Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.
•
Assemble two 3-1/2” PULLEYS (24) into FRAME (1) using two 3/8 X 3-3/4” BOLTS (30), four 3/8 X 1-1/16”
FLANGE SPACERS (42) and two 3/8” LOCK NUTS (34) and tighten securely.
•
Assemble one 3-1/2” PULLEY (24) into PRIMARY PIVOT (9) upper hole using one 3/8 X 8-3/4” BOLT (31),
two 3/8” FLAT WASHERS (36), two 3/8 X 1-1/2” SPACERS (44) and one 3/8” LOCK NUT (34) and tighten securely
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
15
Download from Www.Somanuals.com. All Manuals Search And Download.
24
38
3/8 X 3-3/4” 30
1
43
42
34
3/8 X 8-3/4”
31
36
44
9
27
3/8 X 1-3/4”
12
FIGURE 14
STEP 14:
•
Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.
•
Assemble one 3-1/2” PULLEY (24) into the PRIMARY PIVOT (9) lower hole using one 3/8 X 8-3/4” BOLT (31),
two 3/8” FLAT WASHERS (36), two 3/8 X 1-1/2” SPACERS (44) and one 3/8” LOCK NUT (34) and tighten securely.
•
•
Assemble one 3-1/2” PULLEY (24) to the FRAME (1) using one 3/8 X 3-3/4” BOLT (30), two 3/8 X 1-1/16”
FLANGE SPACERS (42), one 3/8” LOCK NUT (34) and tighten securely
Loosely assemble one 3-1/2” PULLEY (24) between PULLEY PLATES (12) using one 3/8 X 1-3/4” BOLT (27) and
one 3/8” LOCK NUT (34).
•
Assemble two 3-1/2” PULLEYS (24) between the left and right BOOM PLATES (4) and (5) using two 3/8 X 3-3/4” BOLTS (30),
two 3/8 X 1” SPACERS (43), two 3-1/2” CABLE GUARDS (38) and two 3/8” LOCK NUTS (34)
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
16
Download from Www.Somanuals.com. All Manuals Search And Download.
20
SECURELY
TIGHTEN
JAM NUT
35
WEIGHT
STACK
SHAFT
FIGURE 15
51
STEP 15
•
Slip ring of WEIGHT SELECTOR PIN (51) down WEIGHT STACK SHAFT and insert pin into one of the weights
•
•
Screw end of LAT CABLE (20) into top of PLATE SHAFT (18) and securely tighten JAM NUT as shown in FIGURE 15
Securely tighten 1/2” LOCK NUT (35) on PRIMARY PIVOT of PRESS ARM (9).
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
17
Download from Www.Somanuals.com. All Manuals Search And Download.
11
29
3/8 x 3”
1
41
34
3/8 x 3-3/4”
30
42
24
34
21
FIGURE 16
36
STEP 16:
•
Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.
•
[CABLE MUST BE POSITIONED BETWEEN PULLEYAND LOWER BOLT ASSEMBLY ON
LEG PEDESTAL (11) AND FRAME (1)]
• Securely assemble the ball end of the LOW CABLE (21) and one 3-1/2” PULLEY (24) to the LEG PEDESTAL (11) using two
3/8 X 3-3/4” BOLTS (30), two 3/8” X 1-1/16” FLANGE SPACERS (42), two 3/8” WASHERS (36), and two 3/8” LOCKNUTS (34).
(NOTE: The LEG CABLE (21) should be routed over the retaining bolt as shown in FIGURE 16.)
•
Securely assemble one 3-1/2” PULLEY (24) and two 3/8 X 3/4 FLANGE SPACERS (41) to the FRAME (1) using one 3/8 X 3”
BOLTS (29), and one 3/8” LOCKNUT (34). (NOTE: The LEG CABLE (21) should be routed over the retaining bolt as shown
in FIGURE 16.)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
12
3/8 X 1 -3/4” 27
36
34
43
24
30
30
3/8 X 3-3/4”
3/8 X 3-3/4”
3
FIGURE 17
STEP 17:
•
Refer to cable ILLUSTRATION “A” on page 14 for cable routing while installing pulleys.
•
Assemble one 3-1/2” PULLEY (24) between BASE PLATES (3) using one 3/8 X 3-3/4” BOLT (30), two 3/8 X 1” SPACERS
(43), one 3/8” LOCK NUT (34) and tighten securely.
•
Loosely assemble one 3-1/2” PULLEY (24) between the PULLEY PLATES (12) using one 3/8 X 1-3/4” BOLT (27), and one
3/8” LOCK NUT (34).
•
•
Secure end of LOW CABLE (21) using one 3/8 x 3-3/4” BOLT (30), one 3/8” FLAT WASHER (36) and one 3/8” LOCK NUT (34)
as shown in FIGURE 17
Tighten both 3-1/2” PULLEYS (24) located on PULLEY PLATES (12)
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
19
Download from Www.Somanuals.com. All Manuals Search And Download.
18
1
39
10
11
54
15
14
FIGURE 18
STEP 18:
•
Attach two 4 X 7” ROLLER PADS (15) to the LEG PEDESTAL (11) using one 3/4 X 17” TUBE (14) and two
3/4” STARLOCK COLLARS (54) as shown in FIGURE 18.
• Attach two 4 X 7” ROLLER PADS (15) to the SEAT ADJUST (10) using one 3/4 X 17-1/2” TUBE (18), two PLASTIC
WASHERS (39) and two 3/4” STARLOCK COLLARS (54) as shown in FIGURE 18.
• Attach two 4 X 7” ROLLER PADS (15) to the FRAME (1) using one 3/4 X 17-1/2” TUBE (18),
two PLASTIC WASHERS (39) and two 3/4” STARLOCK COLLARS (54) as shown in FIGURE 18.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PULLAND
TWIST TO
DISENGAGE
17
49
53
ADJUSTMENT
ADJUSTMENT
TIGHTEN
JAM NUT
19
SECURELY
26
57
25
51
58
FIGURE 19
STEP 19:
•
If upon completion of assembly, the HEAD PLATE (19) does not sit on top of the first WEIGHT PLATE (22), push the
HEAD PLATE (19) down, insert the WEIGHT SELECTOR PIN (51) and perform several repetitions at the press station.
This will relax the cable system and prevent the HEAD PLATE (19) from lifting up. See FIGURE 19
•
If after completing previous step, the HEAD PLATE (19) still does not sit on top of the first WEIGHT PLATE (22) or if
there is excess slack in the cable system, adjust the threaded end of the LAT CABLE (20) and ADJUSTABLE GLIDE (53)
accordingly and retighten the jam nuts. See figure 19
•
•
For maximum performance, the HEAD PLATE (19) should just barely sit on the top WEIGHT PLATE (22)
Attach the LAT BAR (17) to the ball end of LAT CABLE (20) using one SNAP LINK (57) as shown in FIGURE 19.
•
Attach the ANKLE STRAP (25) to the 12 LINK CHAIN (26) using one SNAP LINK (57) as shown in FIGURE 19
Thank you for purchasing the ParaBody GS2 Gym System. If unsure of proper use of equipment, call
your local ParaBody distributor or call the ParaBody customer service department at (800) 328-9714
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your ParaBody customer service representative
at (800) 328-9714.
* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury
* Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.
MODEL #________________________
SERIALNUMER LOCATED ON
PULLEY BRACKET
SERIAL #_________________________
DATE OF PURCHASE: _____________
DEALERS NAME: _________________
DEALERS PHONE #_______________
SERIALNUMBER LOCATION
Thank you for purchasing the ParaBody GS2 Gym System.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY.
1. LIMITED WARRANTY ON FRAMEAND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.
4. CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty.
5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning parts to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.
6. SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.
7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.
8. OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary depending on local law.
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty.
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
NOTES:
23
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFE FITNESS CONSUMER DIVISION
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.
Tel: 763.323.4500 Fax: 763.323.4797
800.328.9714 (Toll-free within the U.S. and Canada)
INTERNATIONALOFFICES
Life FitnessAtlantic BV
Life Fitness (UK) Ltd.
QueenAdelaide
Ely, Cambs CB7 4UB
United Kingdom
Phone CSS: (01353) 665507
Fax CSS: (01353) 666719
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: (180) 646 666
Fax: (180) 646 703
Life Fitness EUROPE GmbH
Siemensstrasse 3
Life Fitness Benelux N.V.
Bijdorpplein 25-31
85716 Unterschleissheim
Germany
2992 LB Barendrecht
The Netherlands
Phone: (089) 31 77 51-0
Fax: (089) 31 77 51 99
Phone: 31 (180) 64 66 69
Fax: 31 (180) 64 66 99
Life Fitness Japan
8/F, Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, Tokyo 151-0051
Japan
Phone: 81 (3) 3359-4309
Fax: 81 (3) 3359-4307
Life Fitness Italia S.R.L.
Via Elvas 92
39042 Bressanone
Italy
Phone: 39 (472) 835-470
Fax: 39 (472) 833-150
Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3º andar (Confab)
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Life FitnessAsia Pacific Limited
Room 2610, Miramar Tower
132 Nathan Road, Tsimshatsui
Kowloon, Hong Kong
Phone: (852) 2891-6677
Fax: (852) 2575-6001
Brazil
Phone: 55 (11)7295-2217
Fax: 55 (11) 7295-2218
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|