ORDER NO.PTD0212U38C1
F16
Cordless Rotary Hammer
EY6813-U1
SPECIFICATIONS
CONTENTS
Page
Page
1 SCHEMATIC DIAGRAM
2
2
3
6
5 TRIAL OPERATION(after checking TROUBLESHOOTING
GUIDE.)
2 WIRING CONNECTION DIAGRAM
3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS
4 TROUBLESHOOTING GUIDE
8
9
6 EXPLODED VIEW
7 REPLACEMENT PARTS LIST
10
© 2002 Matsushita Electric Works Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS
IHOW TO DISASSEMBLE THE MAIN UNIT.
Ref. No. 1A
Procedure 1A
Removal of the housing.
1. Set the hammering/drilling switching lever to the position
the speed/blow mode selection lever in between "H" and "S"
position.
and
2. Loosen the support handle and take it out from the unit.
3. Pluck the chuck cover depressing the chuck handle.
4. Remove 15 housing screws.
For assembling
NOTE :
Make sure to attach the dust preventive clothes or filters on the
housings.
Ref. No. 1B
Procedure 1A→1B
Removal of the motor brush assembly.
1. Loosen 2 screws.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
IHOW TO DISASSEMBLE MAIN UNIT.
Ref. No. 2A
Procedure 1A→1B→2A
Removal of the switch.
1. Take out the heat sink from the housing by something like a plier.
2. Take out the battery holder from the housing.
3. Remove the trigger cover.
For assembling
NOTE:
Make sure to set the trigger cover into the groove of housing.
Ref. No. 2B
Procedure 1A→1B→2A→2B
Removal of the motor assembly.
1. Hitch the brush spring to the frame by something like a forceps and
take the motor brush assembly with the switch out from the motor
assembly.
2. Take out the rotor and the current plate from the motor case.
For assembling
NOTE:
Make sure to return the spring into the groove of the motor brush.
Make sure to align the groove of motor case and the groove of
current plate. And set the largest groove of the motor case onto
the boss of housing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
IHOW TO DISASSEMBLE THE GEAR BOX BLOCK.
Ref. No. 2C Procedure 2A → 2B → 2C
Removal of the gear box block.
1. Loosen 8 screws of the gear case.
2. Take out a steel ball pushing the chuck spring with the chuck
spring plate.
3. Remove the chuck spring, the chuck spring plate and the spindle
& piston assembly.
4. Remove the intermediate shaft assembly.
For assembling
NOTE :
Every time the gear box block is opened, use the new gaskets
and screws.
1. Assemble the bearing with the spindle assembly.
2. Fit O-ring onto the bearing. It is little loose.
3. Assemble the chuck spring and the chuck spring plate.
4. Insert a ball pushing down the chuck spring.
5.Insert the reciprocation bearing shaft into the hole of universal
coupling. Make sure two thrust plates should be set both side of
reciprocation bearing shaft one of each.
NOTE :
Greasing about 30g into the gear box block especially for the
connection area between reciprocation bearing and universal
coupling. In addition, hammer O-ring, inside of piston and
cylinder for output shaft block also need to apply.
Air compressed by the piston drives hammer. Take care to
protect the piston and hammer from contamination by dust.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
4 TROUBLESHOOTING GUIDE
(Refer to WIRING CONNECTION DIAGRAM)
4.1. CHECK POINTS FOR ELECTRICAL PARTS.
< TROUBLE >
< CHECK >
<CHECK BATTERY PACK.>
< REMEDY >
Does not operate.
NO Replace battery
→
If no less than 24V DC is available across the (+) and (-)
terminals after charging the rated charging time (45min.),
the battery pack is OK.
→
pack.
The battery pack is sold separately as an optional
accessory. See the nearest sales dealer for
details. The battery pack has a limited life.
The pack should be replaced if;
NOTE:
- after being charged for the rated charging
time the battery voltage is less than 24V DC
or the usable time is extremely short.
- the battery leaks. Check battery for leaks
and terminals for corrosion.
↓OK
<CHECK TERMINAL CONNECTIONS BETWEEN
MAIN UNIT AND BATTERY PACK.>
NO Repair contacts or
→
replace switch
assembly.
Check for proper terminal contacts or if there is any foreign
substances around the battery terminals of battery holder.
↓OK
<CHECK MOTOR.>
The motor normally operates with its white (+) and gray (-)
lead wires connected to 24V DC.
NO Replace motor
→
rotor and brush
assembly.
Does not speed-
control but switch
trigger works
properly.
<CHECK SWITCH.>
Even if FET block is defective, it can not be replaced
individually. Replace whole switch block.
NO Replace switch &
FET block.
→
→
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
4.2. CHECK POINTS FOR MECHANISM BLOCK.
< TROUBLE >
Does not hammer
or weakness of
hammering.
< CHECK >
< REMEDY >
NO Replace
<CHECK INTERMEDIATE SHAFT ASSEMBLY.>
Check the wear condition of the change clutch and spring.
→
→
intermediate
shaft assembly.
↓OK
<CHECK RECIPROCATION BEARING.>
Check the smooth action between reciprocation bearing
and universal coupling.
NO Replace universal
coupling.
→
↓OK
<CHECK PISTON AND HAMMER BLOCK.>
Check the wear condition of inside of piston and hammer
O-ring.
NO Replace piston
→
assembly and
greasing.
↓OK
<CHECK STRIKER.>
NO Replace spindle
assembly.
Check the smooth action of striker.
→
↓OK
<CHECK INTERMEDIATE SHAFT ASSEMBLY.>
Check the wear condition on tooth for change gears.
NO Replace
intermediate shaft
assembly.
→
Does not drill.
<CHECK BEARING.>
Check the condition of bearing for H/D handle.
NO Replace H/D
handle.
→
→
↓OK
<CHECK O-RING.>
Check the wear condition for O-rings assembled with
striker.
NO Replace spindle
assembly.
→
↓OK
<CHECK RECIPROCATION BEARING.>
Confirm the coming and going operation when rotating the
intermediate shaft with DRILL mode.
NO Replace
intermediate shaft
assembly.
→
It is OK if the reciprocation bearing does not operate.
↓OK
<CHECK STRIKER.>
NO Replace spindle
assembly.
Check the smooth action of striker.
→
Does not change
the speed.
<CHECK BEARING.>
NO Replace H/S
handle.
→
Check the condition of bearing for H/S handle.
→
↓OK
<CHECK INTERMEDIATE SHAFT ASSEMBLY.>
Check the wear condition for both change gear “H” and "S".
NO Replace
intermediate shaft
assembly.
→
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
5 TRIAL OPERATION(after checking TROUBLESHOOTING
GUIDE.)
5.1. HAMMER/DRILL
Confirm the action when setting the H/D handle to HAMMER mode.
Rotation with hammering when the drill bit touches something like stone, and power.
It is OK, if it takes about 7-10 seconds by 20kgf to hole ( 12.5X40) on the concrete (pressure strength 240kgf/cm2).
Confirm the action when setting the H/D handle to DRILL mode.
No hammering when the drill bit touches iron plate.
5.2. SPEED CONTROL
Change the rotation speed from 0-950 rpm in proportion to the amount of pushing level on switch trigger.
5.3. REVERSING LEVER
Confirm the action with setting the reversing lever to FORWARD or REVERSE.
5.4. ASSEMBLY
Confirm pressing the lead wires between ribs, tightening screws firmly and replacing the new gasket and screws for the gear
box block.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
6 EXPLODED VIEW
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EY6813-U1
7 REPLACEMENT PARTS LIST
NOTE:
*B=only available as set
*C=available individually
Ref.No.
1
Part No.
WEY6813K3078
WEY6813H3117
WEY6813K3127
WEY6813L0427
WEY6813L1917
WEY6813L0437
WEY6813L0917
WEY6813L0367
WEY6813L4058
EY6812L0387
WEY6813L4067
EY6812L4627
EY6812L0977
WEY6813L1247
WEY6813L1257
EY6812L0847
WEY6813L4077
WEY6813L0467
WEY6813L0017
WEY6813L0027
WEY6813L0987
WEY6813L9557
WEY6813L0357
WEY6813L4627
WEY6813L4987
WEY6813L4637
WEY6813L0447
EY574B9037
Part Name
HOUSING AB SET
&
Description
Remarks
Per Unit
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
8
1
1
1
1
1
2
1
2
1
1
2
2
2
2
2
1
1
1
1
1
15
1
1
1
1
1
1
2
CHUCK COVER
CHUCK HANDLE
BALL GUIDE
STEEL BALL
3
4
5
7
6
CHUCK SPRING STRIKE PLATE
CHUCK SPRING
7
8
O
RING
35
9
SPINDLE ASSEMBLY
BEARING
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
-
PISTON ASSEMBLY
HAMMER
O
RING
PISTON
UNIVERSAL COUPLING
THRUST PLATE
*B
*B
(2PCS/PK)
(5PCS/PK)
INTERMEDIATE SHAFT ASSEMBLY
THRUST PLATE
GEAR CASE
GEAR CASE
A
B
GASKET AB SET
ALUMINUM TIGHT SCREW (M4X16)
O
RING
MOTOR ROTOR ASSEMBLY
MOTOR CASE ASSEMBLY
MOTOR BRUSH ASSEMBLY
CURRENT PLATE
P
TIGHT SCREW (K3X20)
*C
*C
WEY6813L4157
EY6225L6027
WEY6813Y4607
WEY6813Y4617
WEY6813L0377
WEY6813L0387
WEY505B6967
WEY6813L1407
WEY6813L0457
WEY6813L3137
WEY6813L3147
WEY6813D3157
EY6812L0177
EY6811K3817
EY3503K6208
WEY6813K4627
WEY6813K4637
WEY6813H7727
EY6812T7918
WEY6813X5517
WEY6813K8108
SWITCH ASSEMBLY
SEMS SCREW (M3X5)
H/D HANDLE
H/S HANDLE
O
O
RING
RING
*C
*C
*B
*B
*B
15.5
STEEL BALL
(5PCS/PK)
(2PCS/PK)
(2PCS/PK)
CLICK SPRING
SNAP RING
TRIGGER COVER
F/R HANDLE
RELEASE LEVER
SPRING
A
BATTERY FIXING METAL ASSEMBLY
TAPPING SCREW (K4X20)
AUXILIARY HANDLE
SUPPORT HANDLE
*C
DEPTH GAUGE
BIT GREASE
THIXO GREASE
-
OPERATING INSTRUCTIONS
** Battery Pack, Dust Collecting Cup and Tool Case are available as an optional accessory.
See the nearest sales dealer for details.
*** For replacement parts of charger, see the charger service manual.
Charger complete set is available as an optional accessory. See the nearest sales dealer for details.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|