Digital Video Cassette Recorder
AJ-
DCP
Operating Instructions
Printed in Japan
VQT8017-3
D
F10399W3040
P
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Superimposed Screens . . . . . . . . . . . . . 21
Setup (Initial Settings) . . . . . . . . . . . . . 23
Setting method using on-screen menus . . . . . . . 23
How to return to the factory settings . . . . . . . . . . 23
How to set the user defaults . . . . . . . . . . . . . . . . 24
How to load the user defaults . . . . . . . . . . . . . . . 25
How to protect the menus . . . . . . . . . . . . . . . . . . 25
How to release the menu protection . . . . . . . . . . 26
How to display the DIAG menu . . . . . . . . . . . . . 26
Parts and Their Functions . . . . . . . . . . . . 5
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connector areas . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Example of Connections . . . . . . . . . . . . 11
Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Types of tapes and their recording times . . . . . . 12
Operations . . . . . . . . . . . . . . . . . . . . . . . 13
Turning on the power/inserting a cassette . . . . . 13
Stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setup Menus . . . . . . . . . . . . . . . . . . . . . . 27
SYSTEM menu . . . . . . . . . . . . . . . . . . . . . . . . . . 27
BASIC menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
OPERATION menu . . . . . . . . . . . . . . . . . . . . . . 30
INTERFACE menu . . . . . . . . . . . . . . . . . . . . . . . 31
TAPE PROTECT menu . . . . . . . . . . . . . . . . . . . 32
TIME CODE menu . . . . . . . . . . . . . . . . . . . . . . . 33
VIDEO menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
AUDIO menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Pause/recording
(back-space assemble recording) . . . . . . . . . . . 14
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cue/review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Still-picture playback . . . . . . . . . . . . . . . . . . . . . . 15
Linear 0.3a speed playback . . . . . . . . . . . . . . . . 16
Variable speed playback . . . . . . . . . . . . . . . . . . 16
Audio channels . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Error Messages . . . . . . . . . . . . . . . . . . . 38
Emergency Eject . . . . . . . . . . . . . . . . . . 39
Video Head Cleaning . . . . . . . . . . . . . . . 40
Condensation . . . . . . . . . . . . . . . . . . . . . 40
Maintenance . . . . . . . . . . . . . . . . . . . . . . 40
Specifications . . . . . . . . . . . . . . . . . . . . . 41
Time Codes/User’s Bit . . . . . . . . . . . . . . 19
Time codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
User’s bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the time code . . . . . . . . . . . . . . . . . . . . . 19
Setting the user’s bit . . . . . . . . . . . . . . . . . . . . . . 20
Time code/user’s bit playback . . . . . . . . . . . . . . 20
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The AJ-D95DCP is a multi-purpose digital VTR which
is capable not only of 525i/50 Mbps recording and
playback using 1/4-inch wide compact cassette tapes
but of recording and playback onto existing DVCPRO
(25 Mbps) cassette tapes as well.
This VTR with its high picture quality, which is due to
the use of digital compression technology, significantly
reduces the deterioration in the quality of both sound
and picture accompanying dubbing operations.
Its compact size and light-weight design makes it easy
for the unit to be carried around and installed in a
rack.
A dialogue system enables the unit’s settings to be
performed while monitoring the on-screen menus that
appear on the TV monitor.
Features
Compact size and lightweight
On-screen menu settings
Detailed function settings tailored to the individual
user can be performed on-screen.
The unit is 8-7/16˝ (214 mm) wide, 5-1/4˝ (132 mm) high
and 16-15/16˝ (430 mm) deep, weighing 17.16 lb (7.8
kg).
It comes equipped with grips, which come in handy
when the unit is to be carried.
Audio level controls featured
The level of the signals for the two audio channels can
be adjusted for recording and playback applications.
Efficient installation in a rack
The unit’s width is less than one-half of the standard
19 inches, while its height is equivalent to 3U.
This means that the unit can be installed in a rack with
twice the efficiency of previous units, a feature which
makes it economical as well.
Time codes
Incorporated inside the unit is a TCG/TCR (time code
generator/time code reader). It is also possible to
input time codes from an external source to enable
regeneration with an external time code.
Long-time recording and playback
Installation of SDI connector enabled
An optional SDI input/output board (model AJ-YA95P)
for deriving the maximum from the digital VTR’s
features can be installed.
When an L size cassette is used, the maximum
recording and playback time is 92 minutes in the 50
Mbps mode and 184 minutes in the 25 Mbps mode.
(using AJ-5P92LP )
9-pin remote control
For AJ-5P92LP cassette tapes recorded using the
DVCPRO (25 Mbps) mode, use a VTR supporting
DVCPRO (25 Mbps) 184 minute tapes.
This unit comes with a 9-pin remote control connector
so that the unit can be operated using an optional
external remote controller (model AJ-A95P).
Encoder remote control
Both L and M size cassettes supported
The unit’s 15-pin encoder remote control connector
enables adjustments to be made to the analog video
output section using an optional external encoder
remote controller (model AU-ER65B).
This unit employs a front loading mechanism to
support the recording or playback of DVCPRO or
DVCPRO 50 format size L and M cassette tapes.
AC or DC operation
This unit supports power supplied from both AC 120V
and DC 12V sources.
Back-space assemble recording function
By using the REC button and PAUSE button
together— a combination which activates the auto
back function— pictures can be joined smoothly with
no disturbances.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
Front panel
Counter display area
SCH SERVO
REC INH REMOTE WIDE
CTL
TC
-25 -20 -16 -12 -8 -4
0
dB
-
-30
CH 1
UB
CH 2
HOURS
MINUTES
SECONDS
FRAMES
EJECT
POWER
C
ON
B
OFF
LOCAL REMOTE
INPUT SELECT
MENU
ANALOG
SDI
OFF
ON
REC INHIBIT
REC
PB
PULL
FOR VAR
CH1
CH2
·
CH 3 4
50Mbps
25 50
RESET
REW
PAGE
STOP
FF
PLAY PAUSE/STILL
REC
SET
TAPE
EE
AUDIO OUT
SEARCH
CH1
ST
COUNTER
CH2
DOWN MENU UP
MODE
j
DATA
i
AUDIO MON SELECT
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
Front panel
1 POWER switch
: Level meter
When this switch is pressed, the power is turned on
and the counter display area lights; when it is
pressed again, the power is turned off.
This displays the levels of the audio signals.
The level of the input audio signals is displayed
during recording and E-E selection; the level of the
output audio signals is displayed during playback.
2 Cassette insertion slot
; Cassette insertion and tape travel display lamp
This lamp lights when a cassette has been inserted
into the unit.
Newsgathering cassettes and general-purpose
cassettes are inserted into this slot.
<Note>
Do not insert DV cassettes, which are designed for
general consumer applications.
: When a tape has been inserted and the
STANDBY ON status has been
established
: When a tape has been inserted and the
STANDBY OFF (HALF LOADING) status
has been established
: While the tape is traveling, the segment
display moves as the tape travels.
: The “ ” symbol at the stopped side
flashes when the fan has shut down.
3 EJECT button
When this button is pressed, the tape inside is
unloaded and several seconds later it is
automatically ejected.
If the counter display area is set to the CTL display,
the display will be reset.
4 REC and REC INH lamps
REC:
This lamps lights during recording.
< Counter display area
REC INH: This lamp lights when the cassette is set
to the accidental erasure prevention
status. It also lights when the REC
INHIBIT switch P is at the ON setting.
The TC and CTL counts, the on-screen information
and other messages are displayed in this area.
If DC power is supplied to the unit, the whole
display will flash as a warning when the voltage has
dropped.
In this status, recording is not possible.
5 REMOTE lamp
When the voltage drops to 10.6V or so, the power
will automatically be turned off.
This lamp lights when the REMOTE setting has
been selected by the LOCAL/MENU/REMOTE
switch =.
= LOCAL/MENU/REMOTE switch
This switch is set when menu settings are to be
performed or when the unit is to be controlled from
an external source.
LOCAL: Set here when the unit is to be controlled
using the controls on its operation panel.
6 WIDE lamp
This lamp lights when the WIDE mode has been
selected.
7 SCH lamp
MENU:
Set here when on-screen menu settings
are to be performed.
This lamp lights when the external sync signal
subcarrier phase is within the specified range.
REMOTE: Set here when the unit is to be controlled
using an external remote controller
(model AJ-A95P).
8 SERVO lamp
This lamp lights when the drum servo and capstan
servo lock.
9 Channel condition lamps
One of these lamps lights in accordance with the
error rate statuses. (Green
Blue
Red)
Green: This lamp lights when both the error rates for
the video and audio playback signals are at
an acceptable level.
Blue: This lamp lights when the error rate for
either the video and audio playback signals
has deteriorated. A normal playback picture
will appear even when this lamp is lighted.
Red: This lamp lights when either the video or
audio playback signals are subject to
correction or interpolation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
> INPUT SELECT button and lamp
This button is used to select the input signals.
Each time it is pressed, ANALOG and SDI signals
are selected alternately.
C Headphones jack
When a pair of stereo headphones are connected
to this jack, the sound of the recording or playback
can be monitored through the headphones.
<Note>
D Volume control
It is not possible to select ANALOG for the video
signals and SDI for the audio signals or vice versa:
the same setting must be used for both sets of
signals.
ANALOG: This is selected when analog composite
video signals and analog audio signals
are input. When it is selected, the
ANALOG lamp lights.
This control is used to adjust the headphone
volume.
E Audio monitor selector switch
This switch is used to select the audio monitor
output and headphone output channels.
CH1: The CH1 sound is output through both the left
and right channels.
ST: The sound selected by the settings of setup
menu items No.708 and No.709 is output.
CH2: The CH2 sound is output through both the left
and right channels.
The ANALOG lamp flashes when this
setting is selected but no analog
composite video signals are input.
SDI input signals can be selected when
the optional SDI input/output board has
been installed. When it is selected, the
SDI lamp lights. The SDI lamp flashes
when this setting is selected but no SDI
signals are input.
SDI:
F REW button
This button is pressed to rewind the tape. The
playback pictures can be monitored when the
TAPE/EE switch M is set to TAPE.
Pressing the REW button while in the search mode
(search still, forward search, forward search still,
reverse search still) causes operation to switch to
reverse search, and reverse playback occurs at the
speed selected using setting No. 100 on the setup
menu. (See pages 15 and 30.)
Pressing the REW button while in the slow mode
(slow still, forward slow, forward slow still) causes
operation to switch to reverse linear 0.3a playback.
(See page 16.)
?
Audio signal CH1 and CH2 recording level controls
These controls are used to adjust the recording
levels of the CH1 and CH2 audio signals.
They use a “pull to vary level” system which means
that the levels can be adjusted after they have been
pulled up. The default signal levels apply when
they are pushed down.
@
Audio signal CH1 and CH2 playback level controls
These controls are used to adjust the playback
levels of the CH1 and CH2 audio signals.
They use a “pull to vary level” system which means
that the levels can be adjusted after they have been
pulled up. The default signal levels apply when
they are pushed down.
Noise will appear during linear 0.3a playback: this
is normal and not indicative of malfunctioning.
G STOP button
This button is pressed to stop the tape travel. The
playback pictures can be monitored when the
TAPE/EE switch M is set to TAPE.
The tape drum continues to rotate even in the stop
mode, and the tape remains in close contact with
the drum.
<Note>
The cue audio signal level cannot be adjusted.
A CH3 and CH4 lamp
This lamp lights when TR3/4 is selected as the
setup menu item No.711 setting in the 50 Mbps
mode. It also lights in the E-E mode when the
optional SDI input/output board has been installed,
SDI input is selected, and CH3/4 is selected as the
setup menu item No.712 setting. (During playback,
the lamp is lighted by the No.712 setting.)
(See page 37)
When the stop mode continues beyond the
prescribed period of time, the unit is automatically
set to the STANDBY OFF (HALF LOADING) mode
in order to protect the tape.
The stop mode is established immediately after a
cassette has been inserted into the unit.
B 50 Mbps lamp
This lamp lights when the 50 Mbps mode has been
established.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
H FF button
M TAPE/EE switch
This button is pressed to fast forward the tape. The
playback pictures can be monitored when the
TAPE/EE switch M is set to TAPE.
Pressing the FF button while in the search mode
(search still, reverse search, reverse search still,
forward search still) causes operation to switch to
forward search, and fast forward playback occurs at
the speed selected using setting No. 100 on the
setup menu. (See pages 15 and 30.)
Pressing the FF button while in the slow mode
(slow still, reverse slow, reverse slow still) causes
operation to switch to forward linear 0.3a playback.
(See page 16.)
This switch is used to select the signals to be
output in the stop, fast forward or rewind mode.
TAPE: The signals which are played back from the
tape are output.
EE:
The input signals which were selected by the
INPUT SELECT button are output.
<Notes>
When REC has been set for setup menu item
O
No.105, the E-E mode will be established in the
stop mode regardless of the position of the
TAPE/EE switch. (See page 30)
The picture and sound may break up when the
O
position of the switch is changed.
Noise will appear during linear 0.3a playback: this
is normal and not indicative of malfunctioning.
N COUNTER button
This button is used to switch the counter display
area. Each time it is pressed, the setting is
I SEARCH button
changed in the following sequence: CTL
TC
This button is pressed to switch to the search mode
or the slow mode. (See pages 15 and 16.)
UB CTL, etc.
r
CTL: The tape timer (control signal) appears on the
display.
TC: The time code appears on the display.
UB: The user bit appears on the display.
J PLAY button
This button is pressed to commence playback.
Recording is commenced when it is pressed
together with the REC button.
r:
The amount of tape remaining is displayed in
1-minute increments.
(Example)
“r102” = 102 minutes of tape are remaining.
K PAUSE/STILL button
When this button is pressed during recording, the
tape is temporarily stopped.
Recording is resumed when it is pressed again.
When this button is pressed during playback, the
still picture mode is established. Playback is
resumed when it is pressed again.
O RESET button
When this button is pressed in the CTL mode, the
counter display is reset to 00:00:00:00.
Pressing the PAUSE/STILL button during forward
or reverse search operation causes the tape to
pause (forward or reverse search still). Pressing the
button a second time causes forward or reverse
search operation to resume.
Pressing the PAUSE/STILL button during forward
or reverse slow operation causes the tape to pause
(forward or reverse slow still). Pressing the button a
second time causes forward or reverse slow
operation to resume.
P REC INHIBIT button
This button is used to allow or inhibit recording onto
the cassette tape.
ON: Recording on the cassette tape is inhibited.
The REC INHIBIT lamp on the display lights.
OFF: Provided that the accidental erasure
prevention mechanism on the cassette tape is
set to the recording enable position, a
recording can be made on the cassette tape.
Linear 0.3a playback takes place during forward or
reverse slow operation. Noise will appear during
still and linear 0.3a playback: this is normal and not
indicative of malfunctioning. (See page 16.)
L REC button
Recording is commenced when this button is
pressed together with the PLAY button. When it is
pressed in the stop or eject mode, the input video
signals and audio signals can be monitored even
when the TAPE/EE switch is set to TAPE.
It is also possible to use the button to check the
time code generator’s value. (REC CHECK mode)
When the STOP button or any other function button
is pressed, the REC CHECK mode will be released.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
Connector areas
OFF
75 Ω
ON
REMOTE
REF VIDEO IN
TC IN
IN
OUT
TC OUT
ENCODER
REMOTE
CH 1
AUDIO
IN
CH 2
DC OUT
AC IN
12V 250mA
VIDEO
VIDEO MON
OUT
FUSE 125V 2.5A
AUDIO
MON OUT
L
R
SIGNAL
GND
DC IN
CH 1
AUDIO
OUT
CH 2
1 AC IN socket
This is the AC power inlet.
The accessory power cord is connected here.
3 DC OUT socket
This is the DC 12V output connector.
It is used to supply power to the external remote
controller (model AJ-A95P).
The DC power cable is packed with the model AJ-
A95P controller.
Use an AC 120V ( 10%) power supply to operate
this unit.
When the voltage has dropped to an extremely low
level, the unit’s power is automatically switched off.
It will take several minutes for the unit to be reset
even after the supply voltage is restored. In a case
like this, set the POWER switch to OFF, wait
several minutes, and start up the unit again. AC
power takes precedence when both AC and DC
power supplies have been connected.
Pin No.
Signal
Ground
2
1
3
4
1
2
3
4
+12 V
4 Fuse holder
2 DC IN socket
This contains a 2.5A fuse.
This is the input connector for the DC 12V power.
Use the optional AC adaptor (model AJ-B75).
When the voltage has dropped to around 10.6V, the
unit’s power is automatically switched off. It will
take several minutes for the unit to be reset even
after the supply voltage is restored. AC power
takes precedence when both AC and DC power
supplies have been connected.
5 AUDIO MONITOR OUT (Lch/Rch) connectors
These are the output connectors for the audio
monitor signals. It is possible to select the channel
through which the audio monitor signals are to be
output using the audio monitor selector switch on
the front panel and setup menu item No.708.
(See page 36)
Pin No.
Signal
4
1
2
3
4
Ground
3
2
1
+12 V
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Their Functions
Connector area
6 VIDEO MONITOR OUT connector
This is the output connector for the video monitor
signals. Superimposed video signals can be output
to this connector.
> ENCODER REMOTE connector
An optional external encoder remote controller
(model AU-ER65B) is connected to this connector
when the video output signal settings are to be
adjusted from an external source.
<Note>
Superimposing can be set to ON or OFF by setup
menu item No.002. (See page 29)
Set setup menu item No.00 to REMOTE.
(See page 27)
7 VIDEO IN and OUT connectors
These are the input connector and output
connectors for the analog composite video signals.
Pin No.
Signal
1
9
1
2
8 AUDIO OUT (CH1/CH2) connectors
These are the output connectors for the analog
audio signals.
Set Up
C Level
3
4
Ground
5
+9 V
9 AUDIO IN (CH1/CH2) connectors
These are the input connectors for the analog audio
signals.
6
System H
SYS. SC. Coarse (2)
–9 V
15
8
7
8
9
Hue
: REF VIDEO IN connectors and 75 Ω termination
switch
10
11
12
13
14
15
Video Level
Ret Ground
These are the input connectors for the reference
video signals.
Input black burst signals or composite video signals
which comply with the RS-170A standard.
Set the switch to ON for termination.
SYS. SC. Fine
SYS. SC. Coarse (1)
; TC IN connector
? Fan motor
This motor drives the fan to cool down the unit.
This is the connector for recording the external time
codes on the tape.
@ Grip
< TC OUT connector
Grips are provided on the side panels. However,
when the unit is to be operated, lay it flat.
During playback, the playback time code is output
to this connector. During recording, the time code
generated by the internal time code generator is
output.
A Slot for SDI card (option)
This is the slot for the optional component serial
interface board (SDI input/output board: model AJ-
YA95P).
= REMOTE CONTROL connector
This unit can be operated from an external source
by connecting an optional external remote controller
(model AJ-A95P) to this connector.
<Notes>
Set the LOCAL/MENU/REMOTE switch to the
O
REMOTE position.
This complies with the RS-422A interface
standard but the functions associated with editing
do not work.
O
Pin No.
Signal
Frame Ground
Transmit A
1
6
1
2
3
4
5
6
7
8
9
Receive B
9
5
Receive Common
Transmit Common
Transmit B
Receive A
Frame Ground
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of Connections
4-pin DC power cable (packed with AJ-A95P)
9-pin RS-422A cable (option)
AJ-A95P
AJ-D95DC
OFF
Ω
REF VIDEO IN
ON
REMOTE
Monitor
75
TC IN
IN
OUT
TC OUT
ENCODER
REMOTE
CH 1
AUDIO
IN
CH 2
DC OUT
AC IN
12V 250mA
VIDEO MONITOR output
VIDEO MON
OUT
FUSE 125V 2.5A
AC cable
(packed with unit)
AUDIO
MON OUT
L
R
SIGNAL
GND
DC IN
CH 1
AUDIO
OUT
CH 2
AC 120V or AC adaptor
VIDEO MONITOR output
Speakers with
built-in amplifier
AJ-B75 (option)
4-pin DC power cable (packed with AJ-B75)
Video input signals and reference
video input signals
When signals are to be input simultaneously to the
VIDEO IN connectors and REF VIDEO IN connectors,
make sure that the respective signals are
synchronized.
In a case like this, a normal picture display can be
restored by setting setup menu item No.600 to VF.
(See page 35)
If these signals are not synchronized, the E-E picture
may dance, the advance of the time code display may
slow down, the response to operations may slow
down or some other phenomenon may occur
(although the signals will be recorded normally).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Tapes
<Notes>
Types of tapes and their recording
times
DV tapes bearing either the “
” or “
” logo for
regular consumer applications cannot be used. Do
not insert them into the unit.
M size cassettes
50 Mbps mode
Tapes with a recording/playback length of up to
33 minutes:
25 Mbps mode
Tapes with a recording/playback length of up to
66 minutes:
O
Align the cassette with the center of the insertion slot,
and push it in gently.
Once inserted, the cassette tape is loaded
automatically.
O
AJ-P12MP, AJ-P24MP, AJ-P33MP, AJ-P46MP,
AJ-P66MP
EJECT
POWER
C
ON
B
OFF
LOCAL REMOTE
INPUT SELECT
MENU
ANALOG
SDI
OFF
REC INHIBIT
ON
L size cassettes
50 Mbps mode
Tapes with a recording/playback length of up to
92 minutes:
O
REC
PB
PULL
FOR VAR
CH1
CH2
25 Mbps mode
Tapes with a recording/playback length of up to
184 minutes:
·
O
CH 3 4
AUDIO OUT
50Mbps
25 50
RESET
REW
PAGE
STOP
FF
PLAY PAUSE/STILL
REC
SET
TAPE
EE
SEARCH
MODE
CH1
ST
COUNTOR
CH2
DOWN MENU UP
j
DATA
i
AUDIO MON SELECT
AJ-P34LP, AJ-P66LP, AJ-P94LP, AJ-P126LP,
AJ-5P92LP
For AJ-5P92LP cassette tapes recorded using
the DVCPRO (25 Mbps) mode, use a VTR
supporting DVCPRO (25 Mbps) 184 minute
tapes.
M size
cassette
L size
cassette
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Stop mode
Turning on the power/inserting
the cassette
Before proceeding to operate the unit, check that it
has been connected properly.
The stop mode is established when the STOP
button is pressed.
The stop lamp lights, and the tape stops
1
This unit must be placed on a level surface before any
attempt is made to operate it.
traveling.
In order to protect the tape, the tape protection
mode is established after the time set in setup
menu item No.400 “STILL TIMER” has
elapsed. (See page 32)
When the STOP, REW, FF or PLAY button is
pressed, the corresponding mode is
established.
O
Turn on the power.
1
2
Insert the cassette tape.
Insert the cassette tape at the designated
position without forcing it in any way.
<Precaution for setting STILL TIMER>
At times when, for instance, the same part of the
same tape is repeatedly used, the cumulative
standby time in the same position will be increased.
In order to protect the tape, make the standby time
in the same position as short as possible.
O
Check that the STOP lamp has lighted.
3
When the tape is inserted, the cylinder starts
rotating automatically, the tape is loaded, and the
stop mode is established.
1
2
EJECT
EJECT
POWER
POWER
C
ON
C
ON
B
OFF
B
OFF
LOCAL REMOTE
LOCAL REMOTE
INPUT SELECT
INPUT SELECT
MENU
MENU
ANALOG
SDI
ANALOG
SDI
OFF
ON
OFF
ON
REC INHIBIT
REC INHIBIT
REC
PB
REC
PB
PULL
FOR VAR
PULL
FOR VAR
CH1
CH2
CH1
CH2
·
·
CH 3 4
AUDIO OUT
50Mbps
25 50
RESET
CH 3 4
AUDIO OUT
50Mbps
25 50
RESET
REW
PAGE
STOP
FF
PLAY PAUSE/STILL
REC
SET
TAPE
EE
REW
PAGE
STOP
FF
PLAY PAUSE/STILL
REC
SET
TAPE
EE
SEARCH
SEARCH
MODE
CH1
ST
CH1
ST
COUNTER
COUNTER
CH2
CH2
DOWN MENU UP
MODE
j
DATA
i
DOWN MENU UP
j
DATA
i
AUDIO MON SELECT
AUDIO MON SELECT
1
3
<Note>
The STOP button flashes when no reference video
input signals are supplied if ON has been selected as
the setup menu item No.104 setting. (See page 30)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
When PB has been selected as the setup menu
item No.105 setting, it will take two to three
seconds for recording to commence after the REC
and PLAY buttons have been pressed. (See page
30)
Set this menu item to REC to start the recording
faster. However, with REC set for this item, it takes
longer for the image to appear during playback after
the PLAY button is pressed.
O
Recording
Use the setup menu item No.007 to select
recording in either the 50 Mbps mode or 25
Mbps mode.
1
(See page 29)
Set the accidental erasure prevention tab on
the cassette to the “recording enable”
position, and insert the tape.
2
Press the STOP button to set the unit to the
stop mode.
3
Pause/recording
(with back-space assemble recording)
1. Selecting the input video and audio signals
4
1) Connect the signals that are to be
Press the PAUSE/STILL button while the
cassette tape is being played.
1
recorded.
2) Select the video and audio input signals
using the INPUT SELECT button on the
front panel.
Press the REC button to set the unit to the
REC PAUSE mode.
The monitor screen display now switches to the
E-E picture.
If the setup menu item No. 110 “AUTO BACK” is
set to “REC-P” or “ALL,” the tape is rewound two
to three seconds from the position at which the
PAUSE/STILL button was pressed.
(See page 31.)
2
2. Adjusting the audio levels
Adjust the audio input signal levels.
O
The audio signals are recorded at the
appropriate level when the audio recording
level controls are in the pushed-in position.
Press the PLAY button while holding down
the REC button.
5
The REC and PLAY lamps light, and recording
commences.
Press the PAUSE/STILL button to start
recording.
The tape travels to the position where the
3
If the setup menu item No. 110 “AUTO BACK”
is set to “ALL,” the tape is first rewound two to
three seconds from the position at which the
REC and PLAY buttons were pressed,
advanced, and then recording starts from the
point at which the REC and PLAY buttons
were pressed. This ensures that there are no
gaps between recorded sections.
PAUSE/STILL button was pressed in step , and
1
recording commences.
<Notes>
The E-E picture now appears on the screen.
Recording with back-space assemble
recording from the 50 Mbps mode to the 25
Mbps mode and vice versa is not possible.
O
O
(See page 31.)
Press the PAUSE/STILL button to pause
recording.
If the setup menu item No. 110 “AUTO BACK” is
set to “REC-P” or “ALL,” the tape is rewound two
to three seconds from the position at which the
PAUSE/STILL button was pressed and then
pauses.
To stop recording, press the STOP button.
Recording now stops and the unit is set to the
stop mode.
4
5
6
<Notes>
It is not possible to select ANALOG for the video
O
input signals and SDI for the audio input signals or
vice versa— the same setting must be used for
both sets of signals.
The input signals cannot be recorded properly if a
recording inhibit signal is recorded with them.
Check that the SERVO lamp remains lighted during
recording. The pictures played back will be
disturbed if the lamp is flashing or off.
Repeat steps and above to add recorded
O
O
3
4
sections with no gaps in between.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Playback
VTR
operating mode
Button pressed
Next VTR operation
SEARCH
FF or REW
PLAY or STOP
SEARCH
PLAY or STOP
SEARCH
PLAY or STOP
FF
Search still
Insert the cassette tape.
1
Play or stop
Fast forward
Rewind
Fast forward or rewind
Play or stop
Press the PLAY button.
Regular playback now commences.
2
Forward search
(fast forward playback)
To end playback, press the STOP button.
The unit is now set to the stop mode.
3
Play or stop
Reverse search
(reverse playback)
<Notes>
Check that the SERVO lamp remains lighted during
playback. The playback pictures will be disturbed if
the lamp is flashing or off.
Select the 50 Mbps mode or 25 Mbps mode—
whichever corresponds to the recording mode of
the tape— for the setup menu item No.007 setting.
The recording mode can be identified and the
playback mode can be switched automatically by
selecting AUTO as the setup menu item No.008
setting. (See page 29)
O
Play or stop
Forward search
(fast forward playback)
Search still
O
Reverse search
(reverse playback)
REW
SEARCH
REW
Fast forward
Forward search
(fast forward
playback)
Reverse search
(reverse playback)
PAUSE/STILL
SEARCH
FF
Forward search still
Rewind
However, in this case, it may take some moments
for the mode to be identified.
The pictures may be disturbed when playback
starts.
O
Reverse search
(reverse playback)
Forward search
(fast forward playback)
PAUSE/STILL
Reverse search still
PAUSE/STILL,
SEARCH or FF
Forward search
(fast forward playback)
Forward search
still
Cue/review
Reverse search
(reverse playback)
REW
Pressing the FF button or REW button while in the
search mode (search still, forward search, reverse
search, forward search still, reverse search still)
causes fast forward or reverse playback to occur at
the speed selected using setting No. 100 on the setup
menu. (See page 30.)
Also, pressing the SEARCH button while in the fast
forward or reverse rewind causes the speed to be
reduced to the speed selected using setting No. 100
on the setup menu and fast forward or reverse
playback to occur.
PAUSE/STILL,
SEARCH or REW
Reverse search
(reverse playback)
Reverse search
still
Forward search
(fast forward playback)
FF
PLAY
STOP
Play
Stop
All modes
Still-picture playback
Pressing the PAUSE/STILL button during fast forward
or reverse playback causes the tape to pause.
Pressing the button a second time causes fast forward
or reverse playback to resume.
Press the PAUSE/STILL button during playback.
To restore regular playback, press the PAUSE/STILL
button again.
<Notes>
No sound can be heard during still-picture
O
playback.
Noise may appear on the still picture.
O
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Variable speed playback
(When AJ-A95P is connected)
a
Linear 0.3 speed playback
Pressing the SEARCH button when in play pause
status causes the mode to switch to slow still.
In this status, pressing the FF button or REW button
causes operation to switch to linear 0.3a playback.
Pressing the PAUSE/STILL button during linear 0.3a
playback causes the tape to pause.
When the optional AJ-A95P remote controller is
connected to the REMOTE connector, variable speed
playback is enabled by operating the search dial on
the AJ-A95P.
<Notes>
Pressing the PAUSE/STILL button a second time
causes linear 0.3a playback to resume.
Noise appears on the screen during playback at
any tape speed except the normal tape speed (1a).
During variable speed playback, the sound
recorded on the analog cue track is played back.
O
O
<Note>
Noise appears during linear 0.3a speed playback.
O
VTR
operating mode
Button pressed
PAUSE/STILL
Next VTR operation
Play
Play pause
Play
PAUSE/STILL or
PLAY
Play pause
Slow still
SEARCH
PLAY
FF
Slow still
Play
Forward slow
Reverse slow
Reverse slow
Forward slow still
Forward slow
Reverse slow still
REW
REW
Forward slow
Reverse slow
SEARCH or
PAUSE/STILL
FF
SEARCH or
PAUSE/STILL
PAUSE/STILL,
SEARCH or FF
Forward slow
Reverse slow
Reverse slow
Forward slow still
Reverse slow still
REW
PAUSE/STILL,
SEARCH or REW
FF
Forward slow
Play
PLAY
STOP
All modes
All modes
Stop
Fast forward
Rewind
STOP
STOP
FF
REW
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Audio channels
The DVCPRO (25 Mbps) format has 2 audio channels
whereas the DVCPRO 50 (50 Mbps) format has 4
audio channels.
The settings for setup menu items No.711 and 712
are used to select recording or playback in the 50
Mbps or 25 Mbps mode. (See page 37)
However, this unit uses only two of the channels
provided with the DVCPRO 50 (50 Mbps) format.
50 Mbps mode
25 Mbps mode
<During recording>
<During recording>
$ Analog signal input
$ Analog signal input
Recording
Recording
Audio recording
track on tape
Audio recording
track on tape
Input channel
Input channel
CH1
CH2
CH1
CH1
CH2
CH1
CH2
CH2
CH3
$ Serial digital multiplex signal input (SDI: option)
(Setup menu item No.712 setting: CH1/CH2)
CH4
Recording
Audio recording
track on tape
Input channel
$ Serial digital multiplex signal input (SDI: option)
(Setup menu item No.712 setting: CH1/CH2)
CH1
CH2
CH3
CH4
CH1
Recording
Audio recording
track on tape
Input channel
CH2
CH1
CH2
CH1
CH2
No sound recorded.
No sound recorded.
CH3
(Setup menu item No.712 setting: CH3/CH4)
CH4
Recording
Audio recording
track on tape
Input channel
CH3
CH4
No sound recorded.
No sound recorded.
CH1
CH2
CH3
CH4
No sound recorded.
No sound recorded.
CH1
(Setup menu item No.712 setting: CH3/CH4)
Recording
Audio recording
track on tape
Input channel
CH2
CH1
CH2
CH3
CH4
No sound recorded.
No sound recorded.
CH1
CH2
CH3
CH4
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
50 Mbps mode
25 Mbps mode
<During playback>
<During playback>
$ Analog signal output
$ Analog signal output
(Setup menu item No.711 setting: TR1/TR2)
Playback
Audio recording
track on tape
Output channel
Playback
Audio recording
track on tape
Output channel
CH1
CH2
CH1
CH2
CH1
CH1
CH2
CH2
No sound
played back.
$ Serial digital multiplex signal output (SDI: option)
CH3
No sound
played back.
Playback
Audio recording
track on tape
CH4
Output channel
(Setup menu item No.711 setting: TR3/TR4)
CH1
CH2
CH1
CH2
CH3
CH4
Playback
Audio recording
track on tape
Output channel
No sound
played back.
CH1
CH2
CH3
CH4
No sound
played back.
CH1
CH2
$ Serial digital multiplex signal output (SDI: option)
(Setup menu item No.711 setting: TR1/TR2)
Playback
Audio recording
track on tape
Output channel
CH1
CH2
CH1
CH2
CH3
CH4
No sound
played back.
CH3
CH4
No sound
played back.
(Setup menu item No.711 setting: TR3/TR4)
Playback
Audio recording
track on tape
Output channel
No sound
played back.
CH1
CH2
CH3
CH4
No sound
played back.
CH1
CH2
CH3
CH4
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Codes/User’s Bit
Time codes
Setting the time code
Time codes are used to indicate the absolute position
of the tape in hour, minute, second and frame
increments: the time code signals generated by the
time code generator (time code signal generator) are
recorded on the tape and read by the time code
reader (time code signal reader).
Set the VTR to the menu mode.
(Set the LOCAL/MENU/REMOTE switch to the
MENU position.)
1
Select setup menu item No.505 “TC PRESET.”
(See page 33)
2
Time codes are written into the sub-code area (data
area) on the helical track.
This enables the VTR’s playback to be read out from
the stop mode through slow-motion playback to high-
speed playback.
The time code value appears on the display or is
superimposed onto the screen.
The first digit flashes when the DATA+ button
(PAUSE/STILL button) or DATA– button
(PLAY button) is pressed.
3
The digit whose value is to be changed is
4
TCR 00 :
07 :
04 :
24
moved and flashes when the MENU-UP button
(FF button) or MENU-DOWN button (STOP
button) is pressed.
Hours Minutes Seconds Frames
Change the value using the DATA+ button
(PAUSE/STILL button) or DATA– button
(PLAY button).
5
User’s bit
Among the time code signals, the user’s bit refers to
the 32-bit (8-digit) information frame that is released to
the user. It can be used to record the operator
number or any other information.
Upon completion of the settings, press the
6
SET button (REC button).
Operation now returns to the regular menu
screen.
The alphanumerics which can be used for the user’s
bit are numbers 0 through 9 and letters A, B, C, D, E
and F.
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
7
<Notes>
The current time code value is displayed as the
default.
O
O
O
The display is reset to 00:00:00:00 if the RESET
button is pressed when TC PRESET is set.
The time code cannot be used unless setup menu
item No.504 “TC MODE” is set to “P-REC” or “P-
FREE.” (See page 33)
When the MODE button (SEARCH button) is
pressed without the SET button having been
pressed upon completion of the settings, the time
code setting is canceled, and operation returns to
the regular menu screen.
O
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Codes/User’s Bit
Setting the user’s bit
Time code/user’s bit playback
Set the VTR to the menu mode.
(Set the LOCAL/MENU/REMOTE switch to the
MENU position.)
Set the VTR to the stop mode.
1
1
Set to TC or UB using the COUNTER button.
2
Select setup menu item No.506 “UB
PRESET.” (See page 33)
TC: The time code appears on the display.
2
UB: The user’s bit appears on the display.
If the time code cannot be read, it is
interpolated using the CTL signal.
O
Now follow the same procedure as for setting
the time code.
Press the PLAY button.
Playback is now commenced, and the time code
appears on the display.
3
When “ON” has been selected as the setup menu
item No.002 setting, the time code will be
superimposed onto the video signals from the
MONITOR OUT connector. (See page 29)
<Notes>
The colon between the seconds and frames
O
changes to a period when a drop frame time code
has been read.
When the time code signal is missing, it is
automatically interpolated by the CTL signal.
The following appears on the display.
O
T
R
00 : 07 : 04 : 24
The colon between the seconds and frames
changes to a period when a drop frame is read.
An asterisk ( ) appears when the time code
signal is missing.
(For superimposing only)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Superimposed Screens
When the unit’s MONITOR OUT connectors have
been connected to a TV monitor, the control signals,
time codes, etc. can be displayed as abbreviations on
the TV monitor screen.
This display can be set to ON or OFF by setting setup
menu item No.002. (See page 29)
Display position
The position of the superimposed display characters
can be changed by setting setup menu items No.004
“CHARA H-POS” and No.005 “CHARA V-POS.”
(See page 29)
TV monitor
No display
TCR
:
:
:
: Normally, no display.
P : Flashes when the DC
supply voltage has
dropped.
TCR
:
:
:
TCR
:
:
:
S : Flashes in “FAN STOP”
status.
TV monitor
TV monitor
L : Flashes in “LOW RF”
status.
N : Flashes in “NO RF”
status.
<Notes>
When the PAGE button and DATA+ button or DATA–
button are pressed, the counter display appears
temporarily on the TV monitor while these buttons are
held down to enable the setting to be checked.
Abbreviations
CTL
TCR
UBR
(control signal)
(playback value of time code)
(playback value of user’s bit)
Even while the PAGE button is pressed, the settings
can be performed using the DATA+ button or DATA–
button while the actual status is checked.
REMAIN (remaining tape)
Display characters
The background of the superimposed display
characters can be changed by setting setup menu
item No.006 “CHARA TYPE.” (See page 29)
TCR
:
:
:
TCR
:
:
:
TV monitor
TV monitor
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Superimposed Screens
Operation modes
<Notes>
When the beginning or end of the tape has been
The details to be displayed on the screen can be
selected by setting setup menu item No.003
“DISPLAY SEL.” (See page 29)
O
detected in the VTR operation mode, “BOT
(beginning of tape)” or “EOT (end of tape)” is
displayed at the beginning of the line.
Examples of what is displayed:
EOT STOP
“TIME”: Counter value
“T&STA”: Counter value, VTR operation mode
“T&R”:
Counter value, amount of remaining tape
(stop mode at end of tape)
“T&S&R”: Counter value, VTR operation mode,
BOT STANDBY OFF
amount of remaining tape
(standby mode at beginning of tape)
In the T&S&R mode, one of the following error
displays appears on the third line (line with the
amount of remaining tape).
O
TIME mode
[FAN STOP]:
This appears when the cooling fan has stopped.
When this happens, “E-10” and the counter value
appear alternately on the front panel’s counter
display area.
Counter value
TCR
:
:
:
[NO RF]:
TV monitor
This appears when a blank section has been
detected on the tape.
“E-09” appears on the front panel’s counter
display area.
T&STA mode
[SERVO NOT LOCKED]:
This appears when the servo is not locked.
“E-00” appears on the front panel’s counter
display area.
Counter value
TCR
STOP
:
:
:
[LOW RF]:
VTR operation mode
This appears when there is no head output.
“E-01” appears on the front panel’s counter
display area.
TV monitor
T&R mode
[HIGH ERROR RATE]:
This appears when the error rate has
deteriorated (when the channel condition
appears in red).
“E-02” appears on the front panel’s counter
display area.
Counter value
TCR
:
:
:
REMAIN
MIN
Amount of remaining tape
TV monitor
T&S&R mode
Counter value
TCR
STOP
REMAIN
:
:
:
VTR operation mode
Amount of remaining tape
MIN
TV monitor
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
The unit’s main settings can be performed and
checked using the on-screen menus which are
displayed on the video monitor connected to the unit.
It is also possible to perform and check the settings
using the item numbers and setting numbers which
appear on the front panel’s display area.
A user setting memory is provided. The desired
settings can be stored in this memory in advance for
use during operation.
Press the MENU-UP button or MENU-DOWN
button to move the cursor ( ) to the menu
item whose setting is to be changed.
The page can be scrolled up or down by pressing
the MENU-UP button or MENU-DOWN button
while holding down the PAGE button.
<Note>
4
Pressing the MODE button while setup menu
item No. 622 (SET UP 25) or setup menu item
No. 623 (SET UP 50) is selected displays a
submenu.
While in this status, steps
performed.
,
and
can be
4 5
6
Setting method using on-screen
menus
To return to the item menu, press the MODE
button while holding down the PAGE button.
Set the LOCAL/MENU/REMOTE switch to the
MENU position.
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
1
Press the DATA+ button or DATA– button to
change the setting.
5
6
Press the SET button to enter the setting.
SET–UP MENU
MAIN
NO.00
To change more than one menu item, repeat
steps 4, 5 and 6 for each item.
00 SYSTEM
000 BASIC
<Note>
The setting can be canceled by pressing the
MODE button.
100 OPERATION
200 INTERFACE
400 TAPE PROTECT
500 TIME CODE
600 VIDEO
When other items are to be changed without the
setting having been entered, press the MODE
button and then proceed with steps 4, 5 and 6.
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
This completes the menu settings.
700 AUDIO
7
In the menu setting mode, the REW, STOP, FF,
SEARCH, PLAY, PAUSE/STILL and REC
function buttons serve as the PAGE, MENU
DOWN, MENU UP, MODE, DATA–, DATA+ and
SET buttons.
How to return to the factory
settings
Press the MENU-UP button or MENU-DOWN
button to move the cursor ( ) to the menu
whose settings are to be changed.
2
3
Set the LOCAL/MENU/REMOTE switch to the
1
MENU position.
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
Press the MODE button to set each item in
turn.
To return to the menu screen, press the MODE
button while holding down the PAGE button.
Press the RESET button.
2
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
SELECT
MODE
0 ESCAPE
1 LOAD
2 SAVE
3 PROTECT
Press the RESET button.
3
4
5
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
SELECT
MODE
0 ESCAPE
1 LOAD
2 SAVE
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the LOAD
position, and press the SET button.
The unit is set to the LOAD mode, and the load
screen appears on the video monitor.
3
3 PROTECT
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the SAVE
position, and press the SET button.
The unit is set to the SAVE mode, and the save
screen appears on the video monitor.
SET–UP MENU
NO
<LOAD>
FACTORY (ALL)
FACTORY (NOT SYSTEM)
USER (ALL)
USER (NOT SYSTEM)
SET–UP MENU
NO
<SAVE>
USER (ALL)
USER (NOT SYSTEM)
Press the MENU-UP button or MENU-DOWN
button to move the cursor to FACTORY (ALL),
and press the SET button.
4
5
If this operation is performed with the cursor
moved to FACTORY (NOT SYSTEM) instead,
all the factory settings except for the SYSTEM
menu settings will be restored.
If this operation is performed with the cursor
moved to NO, the factory settings are not
restored, and operation is returned to the
menu screen.
O
Press the MENU-UP button or MENU-DOWN
button to move the cursor to USER (ALL), and
press the SET button.
If this operation is performed with the cursor
moved to USER (NOT SYSTEM) instead, all
the settings except for the SYSTEM menu
settings will be updated.
O
O
If this operation is performed with the cursor
moved to NO, the settings are not updated,
and operation is returned to the menu screen.
O
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
This completes the menu settings.
The screen for checking the SAVE operation
appears. Press the MENU-UP button or
MENU-DOWN button to move the cursor to
the YES position, and press the SET button.
The settings are now saved in the memory.
6
7
How to set the user defaults
SAVE OK?
NO
Set the LOCAL/MENU/REMOTE switch to the
MENU position.
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
1
YES
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
This completes the menu settings.
Perform steps
through
of “Setting
2
2
6
method using on-screen menus,” and change
the items to the desired settings.
(See page 23)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
How to load the user defaults
How to protect the menus
Opening the setup menu can be prevented even when
the LOCAL/MENU/REMOTE switch on the front panel
is set to the MENU position by setting the unit to the
menu protect mode.
Set the LOCAL/MENU/REMOTE switch to the
MENU position.
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
1
Set the LOCAL/MENU/REMOTE switch to the
MENU position.
The unit is now set to the menu setting mode,
and the menu screen appears on the video
monitor.
1
Press the RESET button.
2
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
SELECT
MODE
0 ESCAPE
1 LOAD
Press the RESET button.
2
The unit is set to the default setting mode, and
the default setting screen appears on the video
monitor.
2 SAVE
3 PROTECT
SELECT
MODE
0 ESCAPE
1 LOAD
2 SAVE
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the LOAD
position, and press the SET button.
3
3 PROTECT
The unit is set to the LOAD mode, and the load
screen appears on the video monitor.
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the PROTECT
position, and press the SET button.
The unit is set to the menu protect setting mode,
and a screen for checking whether to protect the
menus appears on the video monitor.
3
4
SET–UP MENU
NO
<LOAD>
FACTORY (ALL)
FACTORY (NOT SYSTEM)
USER (ALL)
USER (NOT SYSTEM)
MENU PROTECT OK?
NO
YES
Press the MENU-UP button or MENU-DOWN
button to move the cursor to USER (ALL), and
press the SET button.
4
5
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the YES
position, and press the SET button.
If this operation is performed with the cursor
moved to USER (NOT SYSTEM) instead,
operation will be performed on the basis of all
the user settings saved in the memory except
for the SYSTEM menu settings.
O
The menu screen is now displayed.
If this operation is performed with the cursor
moved to NO, no change is made to the user
settings saved in the memory, and operation is
returned to the menu screen.
O
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
This completes the menu settings.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (Initial Settings)
How to display the DIAG menu
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
The unit is set to the menu protect mode.
When the LOCAL/MENU/REMOTE switch is set
to the MENU position, the menu setting mode is
not established, and “MENU PROTECTED”
appears on the video monitor screen.
5
This unit has a function for displaying hour meters,
software version and the deck’s serial number on the
video monitor.
Set the LOCAL/MENU/REMOTE switch to the
MENU position while holding down the EJECT
button.
1
<Note>
If the LOCAL/MENU/REMOTE switch is set to
the MENU position while holding down the
COUNTER button on the front panel, the menu
setting mode will be established and the regular
menu settings can be performed even in the
menu protect mode.
The unit is set to the diagnosis display mode, and
“HOURS METER” appears on the video monitor.
DIAG–MENU
HOURS METER
Ser
Perform steps 2 through 7 of “Setting method
H00 OPERATION
H01 DRUM RUN
H02 TAPE RUN
H03 THREADING
H11 DRUM RUN r
H12 TAPE RUN r
00000H
00000H
00000H
00000T
00000H
00000H
using on-screen menus.” (See page 23)
H13 THREADING r 00000T
Any item with “r” can be reset when servicing is
performed.
How to release the menu
protection
While the hour meters are displayed, press
the MENU-UP button or MENU-DOWN button
while holding down the PAGE button.
The deck’s serial number and software version
are displayed on the video monitor.
2
3
Set the LOCAL/MENU/REMOTE switch to the
MENU position while holding down the
COUNTER button on the front panel.
The unit is set to the menu setting mode, and the
menu screen appears on the video monitor.
1
DIAG–MENU VERSION
<NTSC>
FRONT
IF
AV-SYSCON 1.
DV
CYLINDER
REEL
1.
1.
-
-
-
-
-
-
Perform steps and of “How to protect the
2
3
2
3
- .
- .
- .
- .
- .
menus.” and a screen for checking whether to
protect the menus appears on the video
monitor.
1.
1.
1.
MENU PROTECT OK?
NO
YES
When the MENU-UP button or MENU-DOWN
button is pressed again while holding down the
PAGE button, operation returns to the hour meter
display.
Press the MENU-UP button or MENU-DOWN
button to move the cursor to the NO position,
and press the SET button.
Set the LOCAL/MENU/REMOTE switch to the
LOCAL or REMOTE position.
Operation now returns to the normal mode.
The menu protection is now released.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
SYSTEM menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
00 ENCODER SEL
01 VIDEO LEVEL
02 SET UP
For setting whether the encoder adjustments (for the analog video output
signals) are to be performed by the external encoder remote controller or
the unit.
0000
0001
REMOTE 0: Adjustments are performed by the external encoder remote controller.
LOCAL 1: Adjustments are performed by the unit.
0000
–128 For setting the video level as part of the encoder adjustments performed by
the unit.
0128
0 Maximum variation range: 3 dB
0255
0000
127
–128 For setting the setup amount as part of the encoder adjustments performed
by the unit.
0128
0 Maximum variation range: 10 IRE
0255
0000
127
03 HUE
–128 For setting the hue as part of the encoder adjustments performed by the
unit.
0128
0 Maximum variation range: 25 degrees
0255
0000
127
04 CHROMA LEVEL
05 SYSTEM H
–128 For setting the chroma level as part of the encoder adjustments performed
by the unit.
0128
0 Maximum variation range: 3 dB
0255
0000
127
–128 For setting the horizontal phase as part of the encoder adjustments
performed by the unit.
Maximum variation range: 8 µs
0255
127
06 SC COARSE
07 SC FINE
0000
0001
0002
0003
0 For coarsely adjusting SC COARSE as part of the encoder adjustments
90 performed by the unit.
180 Variation range: 4 positions of 90 degrees each
270
0000
–128 For finely adjusting SC PHASE as part of the encoder adjustments
performed by the unit.
Maximum variation range: 45 degrees
Together with the SC COARSE adjustment, 360 degrees are covered.
127
0255
08 SCH COARSE
0000
0001
0002
0003
0 For coarsely adjusting SCH.
90 Variation range: 4 positions of 90 degrees each
180
270
The underlining indicates the factory setting.
<Notes>
Item No. 01, 02, 03 and 04 are initialized only when “ALL” is selected for the initialization operation.
O
O
The (
) setting items are not initialized by the regular menu resetting operation.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
SYSTEM menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
09 SCH FINE
10 AV PHASE
20 P.ON LOAD
0000
–128 For finely adjusting SCH.
Maximum variation range: 45 degrees
Together with the SCH COARSE adjustment, 360 degrees are covered.
0255
0000
127
–128 For adjusting the phase of the audio output to the video output.
Variation range: Increments of 20.8 µs
0255
127
This selects whether or not to load the setup menu user default values
when the power is turned on.
OFF 0: Not loaded
ON 1: Loaded
0000
0001
The underlining indicates the factory setting.
<Note>
The (
) setting items are not initialized by the regular menu resetting operation.
O
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
BASIC menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
000 LOCAL ENA
For setting the switches which can be operated on the front panel when the
REMOTE/LOCAL switch has been set to REMOTE.
0000
0001
0002
DIS 0: None of the switches can be operated.
ST&EJ 1: Only the STOP and EJECT switches can be operated.
ENA 2: All operations are possible except for the COUNTER button and RESET
button.
001 TAPE TIMER
002 SUPER
For setting the CTL counter to the 12-hour or 24-hour display system.
12h 0: 12-hour display system
24h 1: 24-hour display system
0000
0001
For setting whether to display the time code, etc. onto the video monitor
output by superimposing it.
0000
0001
OFF 0: Superimposed data is not displayed.
ON 1: Superimposed data is displayed.
003 DISPLAY SEL
For setting what is to be displayed by superimposing onto the video monitor
output.
0000
0001
0002
0003
TIME 0: Only the time is displayed.
T&STA 1: The time and operation status are displayed.
T&R 2: The time and amount of remaining tape are displayed.
T&S&R 3: The time, operation status and amount of remaining tape are displayed.
004 CHARA H-POS
005 CHARA V-POS
0000
0 For setting the character position in the horizontal direction for the
superimposed display.
4
0004
0008
0000
8
0 For setting the character position in the vertical direction for the
superimposed display.
A setting from 0 to 18 is valid in the T&S&R mode (3-line display).
22 A setting from 0 to 20 is valid in the T&STA mode or T&R mode (2-line
display).
0022
006 CHARA TYPE
007 SYS FORMAT
008 PB FORMAT
For setting the type of superimposed display and menu display.
WHITE 0: White characters are displayed on a black background.
W/OUT 1: White characters with black borders are displayed.
0000
0001
For setting the unit’s recording and playback format.
50M 0: 50 Mbps mode
25M 1: 25 Mbps mode
0000
0001
For setting the format during tape playback.
MANUAL 0: Setting is based on the setting selected for menu item No.007 (SYS
FORMAT).
0000
0001
AUTO 1: Setting is based on the format recorded on the tape.
The underlining indicates the factory setting.
<Notes>
If the PAGE button and DATA+ button or DATA– button are pressed when the CHARA H-POS or
CHARA V-POS item has been set, the counter display appears temporarily while this button is held
down to enable the setting to be checked.
O
Even while the PAGE button is pressed, the settings can be performed using the DATA+ button or
DATA– button while the actual status is checked.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
OPERATION menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
100 SEARCH SPEED
101 SHTL MAX
For setting the speed at which the tape is to be decelerated when the
search switch on the front panel has been pressed.
0: 4.1a normal tape speed
X4.1
0000
0001
1: 8.4a normal tape speed
X8.4
For setting the maximum speed in the shuttle mode when the external
controller connected to the 9-pin remote connector is used.
0: 8.4a normal tape speed
1: 16a normal tape speed
2: 32a normal tape speed
0000
0001
0002
X8.4
X16
X32
102 FF. REW MAX
For setting the maximum fast forward and rewind speed.
0: 16a normal tape speed
1: 32a normal tape speed
0000
0001
0002
X16
X32
X60
2: 60a normal tape speed
<Note>
When the 50M mode has been selected as the menu item No.007 (SYS
FORMAT) setting, the tape will run at 32a the normal tape speed even if
60a has been selected.
103 AUDIO MUTE
For setting the status until the audio signals are output when the unit has
been transferred from the stop mode or search mode to play mode. (This
item functions only with PCM audio signals.)
0000
0001
OFF 0: It takes a shorter time until the audio signals are output.
ON 1: The audio signals are stabilized before they are output.
104 REF ALARM
105 STOP MODE
For setting whether a warning is to be displayed when the reference video
signal has not been connected.
OFF 0: No warning is displayed.
0000
0001
ON 1: A warning is displayed (the stop button flashes when there is a warning).
For setting the mode of the digital circuit in the stop mode.
REC 0: The digital circuit is set to the REC system. It takes a shorter time for
operation to transfer to the REC mode.
0000
In this case, the E-E mode is established regardless of the position of the
TAPE/EE switch.
0001
PB 1: The digital circuit is set to the PB system. It takes a shorter time for
operation to transfer to the playback mode.
106 HUMID OPE
For setting whether to ignore condensation when it has formed and
continue with operation.
0000
0001
OFF 0: Unit does not continue to operate when condensation has formed.
ON 1: Unit continues to operate when condensation has formed in which case it
cannot be guaranteed that the unit will operate normally.
<Note>
Due to the possibility that the tape may be damaged, this item should
normally be set to 0 (no operation).
107 WIDE MODE
108 AUTO REW
For setting whether to perform recording in the wide mode.
WIDE 0: Recording is performed in the wide mode.
NORMAL 1: Recording is performed in the 4:3 normal mode.
0000
0001
For setting whether to automatically rewind the tape to the beginning when
the tape end has been detected by a recording, playback or search
operation.
0000
0001
OFF 0: The tape is not rewound.
ON 1: The tape is rewound to its beginning.
The underlining indicates the factory setting.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
OPERATION menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
109 MEMORY STOP
For setting whether to stop the tape when the CTL counter reading
becomes zero during fast forwarding or rewinding. (This item functions only
in the CTL mode.)
0000
0001
OFF 0: The tape is not stopped.
ON 1: The tape is stopped.
110 AUTO BACK
For setting the operating method in the no-gap mode.
(Specifies whether or not to use the AUTO BACK function, which rewinds
the tape for a few seconds to eliminate gaps and distortion between
segments.)
0000
0001
OFF 0: No AUTO BACK function.
REC-P 1: Auto back is performed when switching to the REC PAUSE mode, after
which the unit remains in REC PAUSE status. (When PAUSE is
cancelled, the tape is advanced and then recording starts.)
ALL 2: In addition to the functions of setting 0001 “REC-P,” AUTO BACK is
performed when switching to the REC PLAY mode, immediately after
which the tape is advanced and recording starts.
0002
111 AFTER CUE-UP
112 CAP LOCK
For setting the status after cue-up.
STOP 0: For stopping the tape in the stop mode.
STILL 1: For stopping the tape in the still mode.
0000
0001
For setting the capstan lock mode.
2F 0: Capstan locks at 2F.
4F 1: Capstan locks at 4F.
0000
0001
113 BATTERY SEL
For setting the type of battery.
NiCd-12 0: 12V battery
NiCd-13 1: 13V battery
0000
0001
0002
NiCd-14 2: 14V battery
114 FRZ MODE SEL
115 EJECT EE SEL
For selecting the output picture in the STANDBY OFF (HALF LOADING)
mode when the TAPE/EE switch has been set to TAPE.
DIS 0: The output picture is muted.
0000
0001
STBOFF 1: The playback picture is frozen for output as soon as the STANDBY OFF
(HALF LOADING) mode is established.
For selecting the video output and audio output while the tape was being
ejected when the TAPE/EE switch has been set to TAPE.
EE 0: The E-E picture and E-E sound are output.
0000
0001
BLACK 1: The E-E picture and E-E sound are muted.
The underlining indicates the factory setting.
INTERFACE menu
Item
Setting
Description of setting
Superimposed
display
Superimposed
display
No.
No.
200 ID SEL
For setting the ID information to be returned to the controller.
0000
0001
OTHER 0: 20 25H is returned.
DVCPRO 1: The DVCPRO unit’s own ID (F0 33H) is returned.
The underlining indicates the factory setting.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
TAPE PROTECT menu
Item
Setting
Description of setting
Superimposed
display
Superimposed
display
No.
No.
400 STILL TIMER
0000
0001
0002
0003
0004
0005
0006
0007
0008
0.5S For setting the time taken until the tape protection mode is established
5S when the unit has been left standing in the stop or still mode.
10S (Unit: S = seconds, min = minutes)
20S
30S
40S
50S
1min
2min
401 SRC PROTECT
For setting the tape protection mode operation when the unit has been left
standing in the still mode.
0000
0001
STEP 0: STEP FWD
HALF 1: STANDBY OFF (HALF LOADING)
<Note>
When STEP FWD has been selected, the unit is automatically transferred to
the STANDBY OFF (HALF LOADING) mode when the total length of time it
has been left standing in the still mode reaches 30 minutes.
402 DRUM STDBY
For setting the drum operation in the STANDBY OFF (HALF LOADING)
mode.
0000
0001
OFF 0: The drum rotation is stopped.
ON 1: The drum rotation is continued.
403 STOP PROTECT
For setting the tape protection mode operation when the unit has been left
standing in the stop mode.
0000
0001
STEP 0: STEP FWD
HALF 1: STANDBY OFF (HALF LOADING)
<Note>
When STEP FWD has been selected, the unit is automatically transferred to
the STANDBY OFF (HALF LOADING) mode when the total length of time it
has been left standing in the stop mode reaches 30 minutes.
The underlining indicates the factory setting.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
TIME CODE menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
500 VITC BLANK
501 VITC POS-1
For setting whether the VITC signal is to be output to the composite video
output.
BLANK 0: VITC signal is not output.
THRU 1: VITC signal is output.
0000
0001
0000
10L For setting the position where the VITC signal is to be inserted.
(The same line as the one used for VITC POS-2 cannot be set.)
16L
0006
0010
0000
20L
502 VITC POS-2
503 TCG REGEN
504 TC MODE
10L For setting the position where the VITC signal is to be inserted.
(The same line as the one used for VITC POS-1 cannot be set.)
18L
0008
0010
20L
For setting the signal which is to be regenerated when the time code
generator (TCG) is in the regeneration mode.
0000
0001
0002
TC&UB 0: Both the time code and user’s bit are regenerated.
TC 1: Only the time code is regenerated.
UB 2: Only the user’s bit is regenerated.
For setting the TCG mode.
0000
0001
0002
0003
P-REC 0: The time code is counted up simultaneously with the recording.
P-FREE 1: The time code is counted up irrespective of the VTR mode.
I-REG 2: The time code is counted up in such a way that it follows on the tape.
E-VITC 3: The mode is synchronized with VITC which is superimposed onto the
video input.
0004
E-LTC 4: The mode is synchronized with LTC in the TC input.
505 TC PRESET
For setting the time code value when P-REC or P-FREE has been selected
as the TCG mode setting by the menu item No.504 (TC MODE).
After the + or – button is pressed, select the digit to be changed using the
UP or DOWN button, and then change the value using the + or – button
again.
506 UB PRESET
507 BINARY GP
For setting the user’s bit value when P-REC or P-FREE has been selected
as the TCG mode setting by the menu item No.504 (TC MODE). After the +
or – button is pressed, select the digit to be changed using the UP or
DOWN button, and then change the value using the + or – button again.
For setting the usage status of the user’s bit which is generated by the
TCG.
0000
0001
000 0: NOT SPECIFIED (character set is not specified)
001 1: ISO CHARACTER (8-bit character set complying with the ISO-646 or
ISO-2022 standard)
010 2: (Undefined)
011 3: (Undefined)
100 4: (Undefined)
101 5: PAGE/LINE
0002
0003
0004
0005
(page/line multiplexing system complying with SMPTE262M standard)
110 6: (Undefined)
111 7: (Undefined)
0006
0007
508 PHASE CORR
For setting whether to control the phase compensation of the linear time
code which is generated by the TCG.
0000
0001
OFF 0: No phase correction control is exercised.
(LTC phase correction bit: 0)
ON 1: Phase correction control is exercised.
(LTC phase correction bit: 1)
The underlining indicates the factory setting.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
TIME CODE menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
509 TCG CF FLAG
For setting whether to add the CF flag of the TCG to the CF bit (color frame
bit) when P-REC or P-FREE has been selected as the TCG mode setting
by the menu item No.504 (TC MODE).
0000
0001
OFF 0: CF flag is not added. (LTC CF bit: 0)
ON 1: CF flag is added. (LTC CF bit: 1)
510 DF MODE
For setting the CTL and TCG drop frame mode.
DF 0: Used in the drop frame mode.
NDF 1: Used in the non-drop frame mode.
0000
0001
The underlining indicates the factory setting.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
VIDEO menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
600 OUT VSYNC
601 V-MUTE SEL
For setting whether to float the vertical sync position of the video output in
order to input the video output phase during E-E mode recording.
N-VF 0: Vertical sync position is not floated.
VF 1: Vertical sync position is floated.
0000
0001
For setting whether to mute the video signals when LOW RF or NO RF has
occurred during playback.
0000
0001
N-MUTE 0: The video signals are not muted (the picture is frozen).
LOW RF 1: The video signal picture is muted (the screen goes blank).
602 CC (F1) BLANK
603 CC (F2) BLANK
604 FREEZE SEL
For setting ON or OFF for the closed caption signals in field No.1.
BLANK 0: Signals are forcibly blanked.
THRU 1: Signals are not blanked.
0000
0001
For setting ON or OFF for the closed caption signals in field No.2.
BLANK 0: Signals are forcibly blanked.
THRU 1: Signals are not blanked.
0000
0001
For setting the freeze mode of still pictures.
FIELD1 0: Field freeze (field No.1)
FIELD2 1: Field freeze (field No.2)
FRAME 2: Frame freeze
0000
0001
0002
605 EDH
For setting whether to superimpose EDH onto the serial output.
(This function works when the optional SDI input/output board has been
installed. When it has not been installed, “N/A” is displayed, and the
function does not work.)
0000
0001
OFF 0: EDH is not superimposed.
ON 1: EDH is superimposed.
606 INPUT C KILL
607 IN FRM DET
622 SETUP 25
For setting the color killer processing for the video input signals.
B/W 0: The video signals are forcibly set to the black-and-white mode.
AUTO 1: The video signals are processed automatically.
0000
0001
For setting frame detection processing during input.
FORCED 0: Frame detection is performed all the time.
0000
0001
AUTO 1: Frame detection is prohibited when non-standard color signals are input.
For setting 7.5% setup processing to be performed on input and output
signals in the 25 Mbps mode.
(The 00 and 01 settings on the submenu can be displayed by pressing the
MODE button.)
00 CMPST IN
01 CMPST OUT
623 SETUP 50
This selects the 7.5% setup processing for the input composite signal.
THRU 0: The signal is recorded in its original form.
CUT 1: The signal is recorded with the 7.5% setup removed.
0000
0001
This selects the 7.5% setup processing for the output composite signal.
THRU 0: The signal is output in its original form.
ADD 1: The signal is output with the 7.5% setup added.
0000
0001
For setting 7.5% setup processing to be performed on input and output
signals in the 50 Mbps mode.
(The 00 and 01 settings on the submenu can be displayed by pressing the
MODE button.)
00 CMPST IN
This selects the 7.5% setup processing for the input composite signal.
THRU 0: The signal is recorded in its original form.
CUT 1: The signal is recorded with the 7.5% setup removed.
0000
0001
01 CMPST OUT
This selects the 7.5% setup processing for the output composite signal.
THRU 0: The signal is output in its original form.
ADD 1: The signal is output with the 7.5% setup added.
0000
0001
The underlining indicates the factory setting.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
AUDIO menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
700 CH1 IN LV
701 CH2 IN LV
702 CH1 OUT LV
703 CH2 OUT LV
0000
0001
0002
0003
4dB For setting the audio input (CH1) reference level.
0dB
–3dB
–20dB
0000
0001
0002
0003
4dB For setting the audio input (CH2) reference level.
0dB
–3dB
–20dB
0000
0001
0002
0003
4dB For setting the audio output (CH1) reference level.
0dB
–3dB
–20dB
0000
0001
0002
0003
4dB For setting the audio output (CH2) reference level.
0dB
–3dB
–20dB
704 EMPHASIS
705 MONI SEL
0000
0001
OFF For setting emphasis ON or OFF.
ON
For setting the audio signals during playback.
PLY PCM 0: PCM audio signals are output.
PLY CUE 1: CUE audio signals are output.
0000
0001
706 REC CUE
707 PB FADE
For setting the audio input signals which are to be recorded on the cue
track.
CH1 0: CH1 input signals are recorded.
CH2 1: CH2 input signals are recorded.
CH1+2 2: CH1 and CH2 input signals are mixed and recorded.
0000
0001
0002
For setting the monitor output and headphone output sound during
playback.
0000
0001
0002
AUTO 0: The sound complies with the status during recording.
CUT 1: The sound is forcibly cut.
FADE 2: The sound is forcibly faded.
708 MONITOR MIX
For setting the audio monitor output method. (This function works when the
audio monitor selector switch on the front panel is set to the ST position.)
STEREO 0: The sound is output in stereo (with the left channel sound from the L
connector and right channel sound from the R connector).
0000
0001
CH1+2 1: The sound is mixed (and mixed sound is output at both connectors).
709 H.PHONE MIX
710 CUE OUT SEL
For setting the headphone output. (This function works when the audio
monitor selector switch on the front panel is set to the ST position.)
STEREO 0: The sound is output in stereo.
0000
0001
CH1+2 1: The sound is mixed (when monaural headphones are used).
For setting whether the analog cue signals are to be output to the audio
output (main line system).
0000
0001
OFF 0: The analog cue signals are not output.
PCM audio signals are output during playback; no sound is output in all
other modes.
ON 1: The analog cue signals are output.
PCM audio signals are output during playback; analog cue signals are
output in all other modes.
The underlining indicates the factory setting.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus
AUDIO menu
Item
Setting
Description of setting
Superimposed
Superimposed
display
No.
No.
display
711 PB AUDIO SEL
712 SDI IN SEL
For setting the audio tracks to be played back. (This function works in the
50 Mbps mode.)
TR1/2 0: The sound recorded on tracks 1 and 2 is played back.
TR3/4 1: The sound recorded on tracks 3 and 4 is played back.
0000
0001
For setting the audio SDI input channels for recording. (This function works
when the optional SDI input/output board has been installed. When it has
not been installed, “N/A” is displayed, and the function does not work.)
CH1/2 0: The SDI input CH1 and CH2 sound is recorded.
0000
0001
CH3/4 1: The SDI input CH3 and CH4 sound is recorded.
713 AUD REC IN
For setting the audio processing method at the point when digital audio
recording is commenced.
0000
0001
CUT 0: Cut processing
FADE 1: V fade processing
714 EMBEDDED AUD
For setting sound multiplexing.
(This function works when the optional SDI input/output board has been
installed. When it has not been installed, “N/A” is displayed, and the
function does not work.)
0000
0001
OFF 0: The sound is not multiplexed.
ON 1: The sound is multiplexed.
715 AUDIO IN SEL
This sets the audio signal input.
(This function works when the optional SDI input/output board has been
installed. When it has not been installed, “N/A” is displayed, and the
function does not work.)
0000
0001
0002
SW 0: Interlocks with the settings of the INPUT SELECT button.
ANALOG 1: Fixes the analog signal input setting.
SDI 2: Fixes the SDI signal input setting.
The underlining indicates the factory setting.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
When trouble has occurred in the unit, one of the following error messages will be displayed on the tape
counter.
Error No.
Description
Error No.
Description
This appears when the loading operations fails to be
completed within 4 seconds.
– d –
Condensation (dew) has formed.
E — 31
E — 32
E — 41
E — 42
E — 43
E — 44
E — 51
E — 52
E — 53
E — 61
E — 62
E — 63
E — 64
E — 65
E — 66
This appears when the servo has failed to lock for
more than 3 seconds.
If “T&S&R” has been selected as the setup menu
item No.003 setting, “SERVO NOT LOCKED” is
displayed on the third line (amount of remaining tape
line) of the monitor screen.
This appears when the unloading operations fails to
be completed within 4 seconds.
E — 00
E — 01
E — 02
This appears when the FG signal (rotational speed
signal) fails to be output from the cylinder motor.
This appears when the PG signal (phase signal) fails
to be output from the cylinder motor.
This appears when there is no head output (due to
clogging, etc.) for more than 3 seconds.
“L” is displayed on the first line (counter line) of the
monitor screen.
If “T&S&R” has been selected as the setup menu
item No.003 setting, “LOW RF” is displayed on the
third line (amount of remaining tape line) of the
monitor screen.
This appears when the cylinder motor speed is
abnormally high.
This appears when the cylinder motor speed is
abnormally low.
This appears when the FG signal (rotational speed
signal) fails to be output from the capstan motor.
This appears when the error rate has deteriorated
(when the channel condition lamps have turned red).
If “T&S&R” has been selected as the setup menu
item No.003 setting, “HIGH ERROR RATE” is
displayed on the third line (amount of remaining tape
line) of the monitor screen.
This appears when the capstan motor speed is
abnormally high.
This appears when the capstan motor speed is
abnormally low.
This appears when the supply reel motor has locked
up.
This appears when a blank portion on the tape has
been detected.
“N” is displayed on the first line (counter line) of the
monitor screen.
If “T&S&R” has been selected as the setup menu
item No.003 setting, “NO RF” is displayed on the
third line (amount of remaining tape line) of the
monitor screen.
When all the following conditions are satisfied, the
part of the tape concerned is recognized as a blank
part.
This appears when the take-up reel motor has
locked up.
This appears when the supply reel motor speed is
abnormally high.
This appears when the take-up reel motor speed is
abnormally high.
E — 09
This appears when abnormal tension has been
detected.
When there is no output from any of the heads
This appears when the start or end processing
operation fails to be completed within 7 seconds.
O
When the playback data cannot be read
O
When there is no CTL signal
O
This appears when there is a communication error
between SERVO and AVSYS. There is a problem
with the data.
This appears when the fan motor has stopped.
“S” is displayed on the first line (counter line) of the
monitor screen.
If “T&S&R” has been selected as the setup menu
item No.003 setting, “FAN STOP” is displayed on
the third line (amount of remaining tape line) of the
monitor screen.
E — 67
This appears when there is a communication error
between SERVO and AVSYS. The data is fixed to
high or low.
E — 68
E — 10
This appears when there is
a
problem in
E — 69
E — 6A
E — 6B
communication between SERVO and AVSYS when
the power is turned on.
The power will be automatically turned off if the fan
remains stopped for more than 5 minutes or so.
This appears when there is a communication error
between IF and FRONT.
This appears when the reel base which operates in
accordance with the size of the tape has locked up
for more than 2.5 seconds.
E — 11
This appears when there is a communication error
between IF and AVSYS. There is a problem with the
internal reference or external reference.
This appears when the cassette down operation fails
to take place even when 4 seconds have elapsed
after the cassette was inserted.
Alternatively, it appears when the cassette fails to be
ejected even when 4 seconds have elapsed after its
ejection operation was performed.
This appears when there is a problem with the
supply voltage.
E — 21
E — 80
This appears when the input DC voltage has
dropped below the undercut voltage (approx. 10.6V).
E — bA
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Emergency Eject
Procedure for removing the tape manually in an emergency
Use the procedure below to remove the cassette tape if it can not be removed even when the EJECT button is
pressed.
Before proceeding to eject the tape manually, you must first turn off the power to the unit.
O
1 Remove the top panel.
4 Once more use the Phillips head screwdriver to
push in and turn the red plastic screw part
counterclockwise. Again rotate the flange part of
the supply reel in the take-up direction to take up
the tape slack.
2 Use a Phillips head screwdriver to push in and turn
the red plastic screw part counterclockwise.
(This screw needs to be rotated about 30 turns
before unloading can be started.)
This two-step procedure needs to be repeated until
the tape is completely housed in the cassette case
(about 90 turns of the red plastic screw part).
3 Insert the take-up jig (packed with the unit) into the
tape ejection slot (on the mechanism side of the
VTR), and rotate the flange part (white gear) of the
supply reel in the take-up direction to take up the
tape slack using the rubber part of the take-up jig.
5 Use the Phillips head screwdriver to turn the red
plastic screw part at the slot-in side clockwise to
eject the cassette tape.
(This screw needs to be rotated through about 140
turns until the tape is ejected.)
<Note>
Take care not to damage the tape in any way.
<Note>
Take care not to sandwich or catch the tape when
closing the cassette cover.
1
5
2
3
4
34
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Head Cleaning
This unit is equipped with an auto head cleaning function, which automatically reduces the
amount of dirt on the video heads. However, in order to enhance the unit’s reliability, it is
recommended that the video heads be cleaned every day. Use a cleaning fluid designated by
the unit’s manufacturer.
Condensation
The same principle by which droplets of water form on a window pane of a heated room is
responsible for the formation of condensation inside the unit.
Condensation occurs in the unit or tape when it is moved from one location to another where
there is a significant difference in temperature and humidity.
More specifically, it forms:
When the unit (or tape) is moved to a very humid location where the air is full of steam, or to a
O
room immediately after it has been heated
When the unit (or tape) is abruptly moved from an air-conditioned location to a very warm or
very humid location
O
When moving the unit to the kind of location described above, do not turn on its power
immediately but leave it standing for about 10 minutes. If condensation has formed inside the
unit, an error message (– d –) will light up on the counter display, and the cassette tape will be
automatically ejected.
Leave the power on, and wait until the error message is cleared.
Maintenance
Before proceeding with maintenance, set the power switch to the OFF position, and disconnect
the power cord from the power outlet. Make absolutely sure that you grasp the power plug when
disconnecting the power cord.
Use a soft cloth to clean the cabinet. To remove stubborn dirt, dilute some kitchen detergent,
soak a rag in the solution, wring it out well, and use it to wipe away the dirt. Wipe up any
remaining moisture using a dry cloth. Do not use paint thinners or benzine.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[GENERAL]
[VIDEO]
$ Digital video
Sampling frequency
(DVCPRO50)
Supply voltage: AC 120V 10%, 50/60 Hz
Power consumption: 93 W
DC supply voltage: 12 V
Y: 13.5 MHz, PB/PR: 6.75 MHz
(DVCPRO)
DC power input current: 6.2 A
Ambient operating temperature
41°F to 104°F (5°C to 40°C)
Ambient operating humidity
10% to 85% (no condensation)
Weight
Y: 13.5 MHz, PB/PR: 3.375 MHz
Quantizing
8 bits
Video compression system
DCT + variable length code
Error correction
17.16 lb (7.8 kg)
Dimensions (WaHaD)
8 7/16˝a5 1/4˝a16 15/16˝ (214a132a430 mm)
Recording format
DVCPRO50 format/DVCPRO format switchable
Recording video signals
525i
Reed-Solomon product code
$ Analog composite IN/OUT
Video band
Y: 30 Hz to 4.5 MHz ( 1 dB)
Differential gain
Less than 6%
Differential phase
Less than 4.5 degrees
Y/C delay
Recording audio signals
DVCPRO50: 48 kHz, 16 bits, 4 channels
O
DVCPRO:
O
48 kHz, 16 bits, 2 channels
Recording tracks
Less than 20 ns
K factor
Digital video/audio: helical track
Time code: helical track (sub-code area)
Cue signal: 1 track
O
O
O
O
Less than 2%
Control (CTL) signal: 1 track
$ Adjustments (video output signals)
Video gain
Tape speed
DVCPRO50: 67.640 mm/sec.
O
More than 3 dB
Chroma gain
More than 3 dB
Hue
More than 25 degrees
Setup
DVCPRO:
O
33.820 mm/sec.
Recording time
92 min. (using AJ-5P92LP, DVCPRO50)
O
33 min. (using AJ-P66MP, DVCPRO50)
O
184 min. (using AJ-5P92LP , DVCPRO)
O
66 min. (using AJ-P66MP, DVCPRO)
O
10 IRE
Horizontal (H) phase
More than 1.5 µs
SC phase (COARSE)
360 degrees
For AJ-5P92LP cassette tapes recorded using
the DVCPRO (25 Mbps) mode, use a VTR
supporting DVCPRO (25 Mbps) 184 minute
tapes.
SC phase (FINE)
Tape used
1/4˝ thin magnetic layer metal tape
90 degrees
FF/REW time
Less than 5 minutes (using AJ-5P92LP)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[AUDIO]
[INPUT/OUTPUT CONNECTORS]
$ Digital audio
Sampling frequency
48 kHz
$ Other input/output connectors
Time code input
BNCa1, 0.5 to 8 VP-P, 8 kΩ
Time code output
Quantizing
BNCa1, 2.0 VP-P, low impedance
16 bits
Frequency response
20 Hz to 20 kHz 1 dB
Dynamic range
More than 85 dB
(1 kHz, emphasis OFF, “A” weighted)
Distortion
Remote
D-sub, 9 pins (female) a1, for AJ-A95P
RS-422A interface standard complied with (no
editing function)
Encoder remote
D-sub, 15 pins (female) a1, for AU-ER65B
DC power output
Less than 0.1%
4 pins a1, DC 12 V, 250 mA, for AJ-A95P
(1 kHz, emphasis OFF, reference level)
Crosstalk
Less than –80 dB
(1 kHz, between 2 channels)
Wow & flutter
Below measurable limits
Headroom
[DISPLAY TUBE]
Counter
8 digits
20 dB
Emphasis
(CTL/TC/UB/amount of remaining tape switchable)
Audio level meter
17 steps + excessive level display
Other
T1 = 50 µs/T2 = 15 µs
(ON/OFF switchable)
Servo lock, tape travel status, recording
enabled/prohibited, SCH, REMOTE, WIDE,
channel condition
[INPUT/OUTPUT CONNECTORS]
$ Video input connectors
Analog composite input
BNCa1, 75 Ω
[OPTIONS]
9-pin remote controller
AJ-A95P
O
O
O
O
Reference input
Analog composite, BNCa2 (loop-through),
75 Ω ON/OFF switchable
Encoder remote controller
AU-ER65B
$ Video output connectors
Analog composite output
BNCa1, 75 Ω
9-pin remote cables
AU-C5 (5 meters), AU-C10 (10 meters)
Component serial interface board
(SDI input/output board)
AJ-YA95P
Monitor output
BNCa1, 75 Ω, superimpose ON/OFF
$ Audio input connectors
Analog input
XLRa2 (CH1, CH2), high impedance,
+4/0/–3/–20 dBu
$ Audio output connectors
Analog output
XLRa2 (CH1, CH2), low impedance,
+4/0/–3/–20 dBu
Monitor output
PHONOa2 (L, R), low impedance, 0 dBu,
CH1/MIX/CH2 switchable
Headphones output
M3a1, stereo, variable level (maximum –20 dBu),
8 Ω, CH1/MIX/STEREO/CH2 switchable
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Mid-Atlantic/New England:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Dallas Region:
6226 Abington Way, Houston, TX 77008 (713) 802-2726
No. CA/Northwest Region:
5870 Stoneridge, #3, Pleasanton, CA 94588 (925) 416-5108
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
Download from Www.Somanuals.com. All Manuals Search And Download.
|