NETWORK
TECHNOLOGIES
INCORPORATED
Tel:330-562-7070
Fax:330-562-1999
1275 Danner Dr
Aurora, OH 44202
17,
USB-ADB USB TO ADB ADAPTER
INSTALLATION / USER GUIDE
MAN009 REV 4/20/01
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
When using the USB-ADB adapter to connect to an NTI KVM switch:
1. Connect the male 8 pin minDIN end of the MKTINT-xx-MM cable to a female 8 pin minDIN Keyboard and Mouse input port on the
NTI KVM switch being used (see Fig. 3). Switch the power ON to the KVM switch if it isn't already.
2. Connect the male 4 pin miniDIN end of the MKTINT-xx-MM cable to either of the 4 pin miniDIN female ports on the USB-ADB
adapter (see Fig. 4).
Mating Face of a 8 Pin miniDIN Female
Fig. 3
Mating Face of a 4 pin miniDIN Female
Fig. 4
3. Connect the USB type B male connector of the USB-AB-0.5M-5T cable (see Fig. 6) to the USB type B female port on the USB-
ADB adapter.
4. Connect the USB type A male connector of the USB-AB-0.5M-5T cable (see Fig. 7) to a USB type A female port on the host
computer. Note: It is important to make this connection last, particularly if the host computer is already ON at the time of
connection.
USB Type A Male
USB Type B Male
Connector
Connector
Fig. 7
Fig. 6
When using the USB-ADB adapter to connect an ADB MAC Keyboard and/or Mouse to a MAC with a USB port:
1. Connect the 4 pin minDIN male connector of the MAC keyboard and mouse assembly into either of the female 4 pin miniDIN ports
on the USB-ADB adapter.
2. Continue with steps 3 and 4 above.
PLEASE NOTE: We recommend that the host computer be configured such that the Sleep Mode is not enabled. However,
if it is necessary to enable the sleep mode, in order to wake up from Sleep Mode, the user must momentarily disconnect the
USB cable connection from either the USB-ADB adapter or from the host computer. Simply unplug the connection, then
plug it back in.
Download from Www.Somanuals.com. All 2Manuals Search And Download.
Technical Specifications
Mating Face of a 4 pin miniDIN Female
Mating face of a USB Type B Female
2
3
1
4
4
3
1
2
PIN # SIGNAL
PIN #
SIGNAL
DATA
PWRN
+5
1
2
3
4
+VCC
- DATA
+DATA
GND
1
2
3
4
GND
Fig. 8
Fig. 9
WARRANTY INFORMATION
The warranty period on this product (parts and labor) is one (1) year from the date of manufacture (indicated on the bottom of the
product). Please contact Network Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at
http://www.nti1.com for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.
COPYRIGHT
Copyright © 2001 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without
the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202
CHANGES
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the right
to make changes in the product design without reservation and without notification to its users.
SERIAL NO.:
INSPECTED BY:
DATE:
Download from Www.Somanuals.com. All 3Manuals Search And Download.
|