Panasonic Car Video System BT LH910G User Manual

Operating Instructions

LCD Video Monitor

Model No.

BT-LH910G

Before operating this product, please read the instructions carefully and save this

manual for future use.

ENGLISH

SS0311HM0 -PS

Printed in Japan

VQT3N15

Download from Www.Somanuals.com. All Manuals Search And Download.

Read this first ! (continued)

EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS

1. Applicable standards and operating environment

The apparatus is compliant with:

• standards EN55103-1 and EN55103-2 2009, and

• electromagnetic environments E1, E2, E3 and E4.

2. Pre-requisite conditions to achieving compliance with the above standards

<1> Peripheral equipment to be connected to the apparatus and special connecting cables

• The purchaser/user is urged to use only equipment which has been recommended by us as

peripheral equipment to be connected to the apparatus.

• The purchaser/user is urged to use only the connecting cables described below.

<2> For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.

• Video signal connecting cables

Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency

applications, for SDI (Serial Digital Interface).

Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended

for analog video signals.

• Audio signal connecting cables

If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.

Use shielded cables, which provide quality performance for high-frequency transmission applications,

for analog audio signals.

• Other connecting cables (IEEE1394, USB)

Use shielded cables, which provide quality performance for high-frequency applications, as

connecting cables.

• When connecting to the DVI signal terminal, use a cable with a ferrite core.

• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following

instructions in this manual.

3. Performance level

The performance level of the apparatus is equivalent to or better than the performance level required by

these standards.

However, the apparatus may be adversely affected by interference if it is being used in an EMC

environment, such as an area where strong electromagnetic fields are generated (by the presence

of signal transmission towers, cellular phones, etc.). In order to minimize the adverse effects of the

interference on the apparatus in cases like this, it is recommended that the following steps be taken with

the apparatus being affected and with its operating environment:

1. Place the apparatus at a distance from the source of the interference.

2. Change the direction of the apparatus.

3. Change the connection method used for the apparatus.

4. Connect the apparatus to another power outlet where the power is not shared by any other

appliances.

Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Centre

Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, F.R. Germany

Download from Www.Somanuals.com. All Manuals Search And Download.

Read this first ! (continued)

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

Transportation precautions

Do not try to lift the

monitor by grabbing

the panel.

Do not place the monitor face down during transportation to

prevent damaging it. Keep it upright.

Do not expose the LCD panel to strong pressure or pressure from pointed objects. Take care especially

during transportation.

Exposing the LCD panel to strong pressure may result in blurring or other damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Read this first ! .....................................................2

Transportation precautions.................................4

Standard accessories · Optional units...............5

About this instruction manual.............................5

Precautions for Use..............................................6

Request .................................................................6

Outline...................................................................7

Selecting Area of Use...........................................8

Dimensions...........................................................9

Controls and Their Functions ...........................10

Front panel........................................................10

Rear panel ........................................................13

Supplying the power ..........................................14

Using an Anton/Bauer battery...........................14

Using a V-mount type battery............................14

Using an external DC power supply..................15

VF Function.........................................................16

How to Remove the Tilt Stand...........................17

On-screen Display..............................................18

Operating status display ...................................18

Main Menu...........................................................24

Menu configuration ...........................................24

2D/3D ASSIST..................................................25

MARKER...........................................................25

Types of MARKER............................................28

VIDEO CONFIG................................................30

SYSTEM CONFIG ............................................34

Performing AUTO CALIBRATION.....................36

RESET operation..............................................37

VF CONFIG ......................................................37

FUNCTION .......................................................38

GPI....................................................................47

INPUT SELECT ................................................48

AUDIO...............................................................49

DISPLAY SETUP..............................................50

CONTROL ........................................................51

HOURS METER ...............................................51

3D Assist Mode...................................................52

MIRROR

(Left/Right and Top/Bottom inversion)...........54

SHIFT (Horizontal and Vertical Shift)................54

COMPARISON (Composition Check)...............54

CONVERGENCE (Convergence Check)..........55

COLOR (Color Check)......................................55

ZOOM FOCUS (Zoom and Focus Check)........56

VERTICAL (Vertical Offset Check)....................57

OVERLAY (Parallax Check)..............................58

Setting Item Restrictions ...................................59

REMOTE Specifications.....................................62

GPI terminal......................................................62

SERIAL terminal ...............................................64

VF (viewfinder) Specifications ..........................68

Error and Warning Displays ..............................69

Maintenance........................................................69

Specifications.....................................................70

Picture and volume adjusting knobs status

display...........................................................19

Sharpness display.............................................19

Function display................................................19

Audio level meter display..................................20

Time code (TC) display.....................................20

Closed caption (CC) display .............................21

DC power supply voltage and battery level

display...........................................................21

How to Use the On Screen Menu......................22

Menu display.....................................................22

Menu operations...............................................22

User Data.............................................................23

Saving user data...............................................23

Loading user data.............................................23

Standard accessories · Optional units

■

Standard accessories

• Tilt Stand × 1 • Tilt Stand Mounting Screw × 4

• CD-ROM × 1

(The unit is shipped with the tilt stand already attached with the four screws.)

■

Optional units

• VF Cable BT-CS910G

About this instruction manual

• This instruction manual refers to BT-LH910G as “this unit.”

• The illustrations, explanatory drawings, and other figures included in this instruction manual are for

illustrative purposes only and may differ from actual display.

• HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks

of HDMI Licensing, LLC in the United States and/or other countries.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions for Use

This product has been specially designed for commercial use. As such, it should be used and operated

only by persons with related expertise.

●

The LCD screen is manufactured to precise

specifications. Although over 99.99 % of the

pixels function normally, 0.01 % of the pixels

are either missing or constantly lit (red, blue

or green). This is normal and not a cause for

concern.

Some video images may appear blurred on the

screen.

Leaving the unit in a location exposed to high

temperature and humidity for an extended period

of time may damage the LCD screen and cause

blurring.

●

The protection panel and liquid crystal panel is a

specially manufactured component. Wiping it with

a hard cloth, or rubbing it vigorously will scratch

the surface.

●

Do not use the unit in excessively dusty

environments. Doing so may damage the LCD

screen.

Using the unit in cases such as the following may

result in image and audio distortion due to the

influence of electromagnetic waves.

If a still image is displayed for an extended period

of time, it may generate a temporary afterimage

(phosphor burn-in). (However, such images can

be removed by displaying normal video for a

while.)

• When in the vicinity of a TV or computer

• When a mobile phone is on top of the unit

• When near equipment that generates a power

magnetic field, such as a speaker or large

motor

●

The response speed and brightness of liquid

crystal vary with ambient temperatures.

Do not install the unit in locations where enough

space cannot be provided around it as heat may

build up inside preventing normal operation. Be

sure to provide enough space around the unit.

●

If the unit becomes unable to operate properly

due the influence of equipment that generates

magnetism, turn off the unit (if using a battery,

remove it) and then wait a while and then turn it

back on.

●

Exposing the LCD screen to intense light sources

will impair its characteristics and lower image

quality.

Using the unit near radio broadcast equipment or

high-voltage equipment may result in image and

audio degradation.

In an environment exposed to drastic temperature

fluctuations, condensation may build up on

and inside the LCD screen. This may lower the

quality of the screen and may damage it. If there

are drops of water on the case, turn off the power

and wait until the condensation has evaporated.

Request

Please configure the following setting before using the unit for the first time.

• The unit is shipped with the area of use set to the initial state. Before using the unit, set

your area of use as described in “Selecting Area of Use” on page 8.

Download from Www.Somanuals.com. All Manuals Search And Download.

Outline

This unit is a liquid crystal display monitor for broadcasting and business use that is equipped with a 23 cm

(9.0 inch) (effective display area) liquid crystal display.

It can be used as a VF (viewfinder) for broadcasting and business cameras made by Panasonic.

■

High Performance Liquid Crystal Panel

This product incorporates a WXGA (1280 x 768) class high-resolution IPS liquid crystal panel. It offers

excellent color reproduction, a wide viewing angle, and a fast response time.

■

Superb Moving Image Quality Achieved by New Image Processing Engine

• The 10-bit image processing engine facilitates accurate and smooth gradation results from low to high

brightness levels.

• The incorporation of an I/P conversion circuit with a low delay of less than one field minimizes the delay

time between signal input and monitor display.

• The incorporation of diagonal line compensation circuit reduces image degradation in the vertical

direction and jagged noise on diagonal lines.

• The high-speed moving image response time provides vivid and clear image display.

• Gamma compensation is performed for each monitor.

■

Includes 3D Assist Functions

Various assist functions are included to allow connecting the left and right connectors of a 3D camera to

the two SDI inputs and capturing 3D images that are easier to view on a 2D monitor. These functions also

make camera adjustments easier and reduce the preparation time required for 3D shooting.

Wide Variety of Functions and Interfaces

• Equipped with 3G-SDI, SDI (HD/SD compatible), HDMI, VIDEO, and YP_BP_Rinputs.

• FOCUS-IN-RED function (Displayed abbreviated to F-IN-R in the picture adjusting knob status display.)

Making camera focus adjustments is extremely easy because the section of the image in focus is

displayed in red to make it easy to understand what is in focus.

• WFM (Y/R/G/B) and vectorscope display functions

Capable of input signal Y/R/G/B waveform display (when 3G-SDI, SDI, HDMI, VIDEO, or YP_BP_Rinput)

and vectorscope display.

• Audio level meter display function and headphones jack

The level of audio signals embedded in 3G-SDI, SDI, and HDMI signals can be displayed. Furthermore,

support is also included for reference point setting, peak hold, and overrange display.

The incorporation of a headphones jack means you can check the audio. The channel can also be

selected in a menu.

• Closed caption function

The captions added to video signals can be displayed during SDI and VIDEO input.

• 2-screen display function

The screen can be split into two to allow you to make a screen comparison for the same input

connectors and same format.

• PIXEL TO PIXEL function

This function makes camera focus adjustment extremely easy because the input signals are displayed

without being resized.

When resizing is not performed, the 1080/60i signals can be expanded to the equivalent of an

approximately 13.5-inch wide monitor, and then checked.

• Cross hatch display function

This function displays markers at regular vertical and horizontal intervals to facilitate easy composition.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Area of Use

The unit is shipped with the area of use set to the initial setting (NTSC) state. Before using the unit, select

the area of use. When you set the area of use, the factory default setting of the menu item on the right is

set to the value that matches the area of use. (For the procedure to restore the menu setting values to the

factory defaults, refer to “Loading user data” on page 23.)

AREA SETTING

NTSC

NTSC (J)

PAL

Menu Item

COLOR SPACE

SMPTE-C

20 dB

EBU

HEAD ROOM

20 dB

18 dB

How to Select Area of Use

1. Connect the unit to the power supply, turn on the power, and press the [MENU] button.

The MAIN MENU screen appears.

2. Press [ ][ ] to select “SYSTEM CONFIG” and press [ENTER].

The “SYSTEM CONFIG” submenu screen appears.

3. Press [ ][ ] to select “AREA SETTING” and press [ENTER].

The “AREA SETTING” value turns green.

4. Press [ ][ ] to select the area of use from “NTSC/NTSC (J)/PAL” and press [ENTER].

The “YES/NO” confirmation screen appears.

5. Press [ ][ ] to select “YES” and press [ENTER].

The setting selected in step 4 is reflected in the factory defaults (FACTORY) or the current menu setting

values and the “SYSTEM CONFIG” submenu screen appears.

6. Press [MENU] twice to close the menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions

Unit: mm(inches)

204 (8-1/16)

20.2

(13/16)

3/8-16UNC*¹

3/8-16UNC

78.5 (3-7/8)

230 (9-1/16)

65.5 (2-9/16)

195.7 (7-11/16)

11.5(7/16)

210 (8-1/4)

20.2 (13/16)

When the adapter is connected: 1/4-20UNC

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls and Their Functions

Front panel

F-IN-R

PEAK/

PHASE

VOLUME/

BRIGHT

CONT./

CHROMA

BT-LH910

B.LIGHT

HEADPHONES output jack (M3 stereo mini jack)

Allows you to connect headphones to check the audio when inputting an SDI signal or HDMI signal.

The volume and sound quality differ depending on the headphones.

• In 3D assist mode, the audio of the SDI1 (L) side can be checked.

POWER switch/lamp

Switches the power supply ON/OFF. When the power is ON, the LED (green) lights up.

INPUT SELECT button

Selects the signal input line. Each time the button is pressed, the input changes in the following order:

VIDEO → SDI1 → SDI2 → HDMI → YP_BP_R→ VF → INT SG

VIDEO : Video input

SDI1

SDI2

: Serial digital interface input (compatible with 3G/HD/SD)

: Serial digital interface input (compatible with HD/SD)

HDMI : HDMI input

YP_BP_R: Analog component input

: Viewfinder input (VF-YP_BP_R/ VF-VIDEO)

INT SG: Internal chart for adjustment [Color Bar + Grayscale] (page 74)

• The input line when the power supply is switched ON is the one that was selected the last time the

power was switched OFF. The INPUT SELECT menu settings can be used to skip input lines that are

not used.

• In 3D assist mode, the input is fixed to SDI1/SDI2 and the input line cannot be selected.

• When the control lock is on, input lines cannot be selected.

• It is not possible to switch to INT SG when two screens are displayed with the SUB WINDOW function

(→ page 42).

The menu is used to set either YP_BP_Ror VIDEO for the viewfinder input.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls and Their Functions (continued)

F-IN-R

PEAK/

PHASE

VOLUME/

BRIGHT

CONT./

CHROMA

BT-LH910

B.LIGHT

MENU, FUNCTION buttons

Use these buttons to display menus, select and adjust settings and confirm menu selections.

/ FUNCTION1

: Press to open a menu, exit a menu or return to a previous menu.

: Moves the cursor downwards and selects items.

It also confirms a menu item assigned to FUNCTION1.

: Moves the cursor upwards and selects items.

/ FUNCTION2

It also confirms a menu item assigned to FUNCTION2.

ENTER / FUNCTION3 : Press to confirm a setting or to open a submenu.

It also confirms a menu item assigned to FUNCTION3.

• When the control lock is on, the key mark appears and FUNCTION does not operate.

• In 3D assist mode, the item of FUNCTION3 is forcefully fixed to the 2D image adjustment mode item

(2D ADJUST).

Picture and volume adjusting knobs/lamps

Functions in 2D (image adjustment) mode

PEAK[PEAKING] 0 - 30 (0) / PHASE 0 - 60 (30)

R-GAIN / R-BIAS (page 32)

Knob1

CHROMA 0 - 60 (30) / F-IN-R (page 46) 0 - 30 (30)

G-GAIN / G-BIAS (page 32)

Knob2

VOLUME 0 - 60 (0) / BRIGHT 0 - 60 (30) /

B-GAIN / B-BIAS (page 32)

Knob3

Knob4 CONT.[CONTRAST] 0 - 60 (50) / B.LIGHT[BACKLIGHT] 0 - 100 (80)

( ) denotes factory preset values.

PEAK F-IN-R VOLUME CONT.

PHASE CHROMA BRIGHT B.LIGHT

[

]

PHASE

EXIT

F-IN-R

PEAK/

PHASE

VOLUME/

BRIGHT

CONT./

(Continued on next page)

CHROMA

B.LIGHT

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls and Their Functions (continued)

Functions in 3D assist mode

MIRROR (MIRROR) / HORIZONTAL (SHIFT) / MODE (CONVERGENCE) /

Knob1 SIZE (COLOR) / ZOOM (ZOOM FOCUS) / EXPAND (VERTICAL) /

OVERLAY (OVERLAY)

VERTICAL (SHIFT) / MANUAL (CONVERGENCE) /

Knob2

FOCUS-IN-RED (ZOOM FOCUS) / MARKER1 (VERTICAL) / MARKER (OVERLAY)

Knob3 SPEED (CONVERGENCE) / MARKER2 (VERTICAL)

Knob4 ASSIST FUNCTION (All Functions)

( ): Selected assist function

• These are rotary push knobs. You can press one of the four knobs to display the corresponding

assigned function and image adjusting knob status, and then make adjustments.

• The setting value is saved and the indication disappears when you press [ENTER] or when 10

seconds elapses after the setting value is changed.

• If you want to change the function assigned to a knob, press the knob and change the function. The

selected function is displayed in green.

• When values are changed from the factory defaults, the LED above the knob (amber) lights.

• Settings are loaded when the monitor is turned on. However, operating changes cannot be made in

the following conditions.

• When the control lock is on, the key mark appears and setting values cannot be changed (page

51).

• When the MONO function is ON (page 31), [PHASE] and [CHROMA] operations are disabled.

• F-IN-R is enabled during operation of the FOCUS-IN-RED function.

• While operating HV DELAY (page 41) (when set to any other setting than OFF), [BRIGHT]

operation is disabled.

• The “CONTRAST” and “BACK LIGHT” operations are disabled in BLACK MODE.

For the operating procedures of adjusting knobs in 3D assist mode, refer to “3D Assist Mode”

(page 52).

Tally Lamps (Red and Green)

Can be lit by a control signal (red tally and green tally) from a GPI/camera.

If the red tally and green tally light at the same time, the tally color will become amber.

Protection Panel

This panel is for protecting the liquid crystal.

• The protection panel can be removed by removing the four screws. When attaching the panel, note

that there is no distinction between the back and front and the top and bottom.

Tilt Stand

The tilt stand allows you tilt the unit 15° forward or 20°

backward.

When tilting the unit, firmly hold the bottom of the stand

and move the top of the unit.

If you want to remove the tilt stand, refer to “How to

Remove the Tilt Stand” on page 17.

<Note>

When tilting the monitor, be careful not to trap a hand

between the monitor and stand.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controls and Their Functions (continued)

Rear panel

12 10 11

SERIAL

20 19

REAR TALLYS (red)

GPI input terminal (D-SUB, 9 pins)

Can be lit by a control signal from a GPI/

camera.

External control is possible by using a GPI

signal.

SDI1 (HD/SD) input terminal (BNC)

SERIAL terminal (D-SUB, 9 pins)

This is the SDI1 input terminal. (Compatible

with HD/SD automatic switching, Compatible

with 3G-SDI)

When you use 3D assist mode (page 51), input

images for the left eye (L).

External control is possible by using an RS-

232C interface.

HDMI input terminal

This is the HDMI input terminal.

DC IN terminal (XLR, 4 pins)

SDI1 active through output terminal

This is the external DC power supply input

terminal.

When a DC power supply is connected

concurrently with the battery, the external

power input takes precedence.

This terminal outputs SDI1 input as is.

SDI2 (HD/SD) input terminal (BNC)

This is the SDI2 input terminal. (Compatible

with HD/SD automatic switching)

When you use 3D assist mode (page 51), input

images for the right eye (R).

Battery holder

This holder is used with a battery made by

Anton/Bauer. (page 14)

SDI2 active through output terminal

This terminal outputs SDI2 input as is.

Screw holes for fixing tripod

VIDEO/Y input terminal (BNC)

There are two screw holes on both the top and

bottom for fixing the unit to a tripod (compatible

with 3/8-16UNC). A removable adapter is

installed in one of the screw holes on the top

of the unit, and enables a 1/4-20UNC screw

to fit in the screw hole. Decide whether to

use the adapter depending on the diameter

of the tripod’s fixing screw. Use a flat-blade

screwdriver to remove or install the adapter.

This is the VIDEO signal (component signal)

input terminal/Y signal (analog component

signal) input terminal.

P_B/P_Rinput terminal (BNC)

This is the P_B/P_Rsignal (analog component

signal) input terminal.

VF terminal (D-SUB, 15 pins)

This terminal connects to the VF (viewfinder)

terminal of broadcasting and business cameras

made by Panasonic.

The unit can be used as the viewfinder for such

a camera.

Screw holes for multi-purpose fixing

There are four screw holes (M3) for multi-

purpose fixing on the rear of the unit, and two

on each the left and right.

Download from Www.Somanuals.com. All Manuals Search And Download.

Supplying the power

An Anton/Bauer battery pack or V-mount type battery pack and external DC power supply can be used to

power this unit.

Using an Anton/Bauer battery

Using a V-mount type battery

■

Batteries for which connection verified

• HYTRON 50

Batteries for which connection verified

• ENDURA E-7S

• DIONIC 90

• ENDURA E-HL9

• DIONIC HC

• ENDURA E-10

1. ^{Install the Anton/Bauer battery pack.}

1. ^{Install the V-mount type adapter plate.}

Battery pack

Adapter plate

2. ^{Insert the battery pack and slide it in the}

direction of the arrow.

Release lever

<Reference> To remove the battery pack

Slide it in the opposite direction to the one in which

it was attached while keeping the release lever on

the battery holder pulled down all the way.

<Reference> To remove the adapter plate

Slide it in the opposite direction to the one in which

it was attached while keeping the release lever on

the adapter plate pulled down all the way.

<Notes>

• For details on the V-mount type adapter plate,

contact the place of purchase.

• When you use a V-mount type adapter plate, the

% (percent) indication cannot be displayed even

if you use a battery with a battery level display

function.

• For details on how to attach the V-mount type

battery, see the instruction manual supplied with

the battery holder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Supplying the power (continued)

Using an external DC power supply

DC IN socket

1. ^{Connect the external DC power supply to the}

DC IN socket on this unit.

1: GND

4: +12 V

DC IN socket

<Notes>

• Use a shield cable with a length of 2 m (6.56 feet)

or less for the DC cord. Use of cords any longer

than 2 m (6.56 feet) may result in noise appearing

on the screen.

External DC

power supply

• If the battery pack and an external DC power

supply are connected simultaneously, then the

external DC power supply will have priority.

If the external DC power supply is used, then the

battery pack may be fitted or removed.

2. ^{Turn “ON” the external DC power supply switch.}

(Where the external DC power supply has a

power switch)

3. ^{Turn “ON” the POWER switch on this unit.}

• If an external DC power supply is used, then make

sure that the external DC power supply is first

turned ON, then this unit is turned ON. If they are

turned ON in the reverse order, then this unit may

malfunction, because the output voltage of the

external DC power supply will gradually increase.

• Input voltage that above the specification is not

displayed accurately.

If an external DC power supply is used, then

check the ratings of the external DC power

supply so that they are compatible with those

of this unit.

Check the pin arrangements of the DC output

terminal of the external DC power supply and

those of the DC IN socket of this unit so that

their polarities are correctly arranged.

If +12 V are supplied to the unit’s GND

terminal by mistake, this may cause fire or

injury.

The external DC power supply cannot be

supplied from the DC output terminal of a

Panasonic camera-recorder because the unit

requires a current that exceeds the output

rating of a Panasonic camera-recorder.

Download from Www.Somanuals.com. All Manuals Search And Download.

VF Function

The unit can be connected to broadcasting and business cameras made by Panasonic and used as a VF (viewfinder).

If you want to use the unit as a VF (viewfinder), remove the tilt stand (page 17).

VF cable (Option)

Part number: BT-CS910G

VF connector on unit side

Camera platform ¹(commercially available)

Camera side VF terminal

Use a camera platform that can fully withstand the weight of the unit (1.7 kg (3.75 lb)).

<Note>

This unit requires a current that exceeds the output rating of a Panasonic camera-recorder, so the external

DC power cannot be supplied from the DC output terminal of a Panasonic camera-recorder.

Do not use the battery pack. If this unit is mounted on the camera-recorder with the battery pack attached,

the camera platform may be damaged. Use an external DC power supply.

Contact your vendor for details of broadcasting and business camera-recorders that will be launched in the

future.

■

Panasonic camera-recorders that allow the unit to be connected as a VF( viewfinder)

VF Communication

VF Video

Monitor

Signals

Camera → Monitor

Panasonic Camera-

→ Camera

recorder

TALLY

Indication of

Abnormal

Operating State

Changing of

Aspect (SD

Mode Only)

YP_BP_RVIDEO ZEBRA

RED

GREEN

AJ-HPX3100G

AJ-HPX3700G

AJ-HPX2700G

AJ-HPX2000/2100

AJ-HDX900



AG-HPX500/502

(Monochrome images

of SD resolution)



Configure the menu settings in accordance with the output signal format of the camera (page 48).

For the settings, refer to the instruction manual of the camera.

The ZEBRA information can be set for the camera (page 37).

The tally lamp on the rear of the monitor lights in accordance with the REAR TALLY setting (page 37).

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Remove the Tilt Stand

When you do not want to use the tilt stand such as when using the unit as a VF (viewfinder), remove the tilt

stand mounting screw (four screws) with a Phillips driver and then remove the tilt stand from the unit.

When attaching the tilt stand, make

sure to align the protrusions for

alignment with the corresponding

alignment holes.

Alignment hole

<Notes>

• When tilting the monitor, be careful not to trap a hand between the monitor and stand.

• When not using the tilt stand, take care that the unit does not fall over.

• When the unit will be permanently installed in one place, we recommend securing it in place using the

screw holes at the bottom of the stand.

Download from Www.Somanuals.com. All Manuals Search And Download.

On-screen Display

The screen shows information such as the operating status display, picture adjusting knob status, sharpness

display, function display, audio level meter display, time code display, closed caption display, DC power

supply voltage and battery level display, and menu display.

Operating status display

5 6

YP^BPR 1080/60i

P-P FILM

DC14.0V

50%

1. The selected input line (page 10)

• SDI1, SDI2, HDMI, VIDEO, YP_BP_R, VF-YP_BP_R/VF-VIDEO, INT SG.

2. Signal format

• “UNSUPPORT SIGNAL” appears if an unsupported signal is input. It may also indicate that the format

selected in the “INPUT SELECT” menu does not match the input signal.

• “NO SIGNAL” appears without input signal.

3. Various indications (PIXEL TO PIXEL mode)

• This indicates the PIXEL TO PIXEL mode is engaged.

4. Various indications (FILM mode)

• This indicates that “GAMMA SELECT” of the “VIDEO CONFIG” is set to “FILM.”

5. Various indications (warning of improper operation status for the camera settings)

• This indicates there is an improper operation status relative to the camera settings.

• The condition to display differs depending on the type and settings of the camera used in combination

with the unit. For details, see the instruction manual of the camera.

6. Various displays (lock setting)

• This indicates that the front operations lock is on. (page 51)

7. DC power supply voltage display

• DC power supply voltage is displayed.

8. Battery level display

• When you are using an Anton/Bauer battery with a battery level display function, the battery level is

indicated by the number of ■ and a percentage. When you are using a battery other than that or the AC

adapter, the display may not be shown or the battery level may not be indicated correctly. The battery

level is indicated by a numerical value in 5 % increments. Also, there are seven ■ segments to indicate

the battery level, and all seven of them are displayed until the battery level is approximately 70 %. After

that, the number of ■ is reduced by one for each 10 % reduction in battery power and no marks are

displayed when the battery level falls below approximately 10 %.

• The indication can be turned ON/OFF in “BATTERY REMAIN” of the “SYSTEM CONFIG” menu (page 34).

<Notes>

• The display state of the status can be set in “STATUS DISPLAY” of the “SYSTEM CONFIG” menu (page 34).

• “UNSUPPORT SIGNAL” and “NO SIGNAL” may not be properly displayed.

• For details on the operation status display in 3D Assist mode, refer to “3D Assist Mode” (page 52).

Download from Www.Somanuals.com. All Manuals Search And Download.

On-screen Display (continued)

Picture and volume adjusting knobs status display

Picture adjusting knob (page 11)

• These are rotary push knobs.

• If you press a knob, the setting value state

appears at the bottom left, and the item assigned

to the corresponding knob is displayed at the

bottom right.

• If multiple items are assigned to one knob, you

can press the knob to switch items.

• The indication disappears when you press

[ENTER] or after 10 seconds of inaction.

• Only adjustments that appear on the screen can

be adjusted.

[

]

PEAK F-IN-R VOLUME CONT.

PHASE CHROMA BRIGHT B.LIGHT

PHASE

EXIT

F-IN-R

PEAK/

PHASE

VOLUME/

BRIGHT

CONT./

CHROMA

B.LIGHT

Status display:

The status of an item can be identified by the

display color of the item name (page 11, “Picture

and volume adjusting knobs”).

White: An item not target for adjustment.

Green: An item target for adjustment.

Gray: An item which cannot be adjusted.

Sharpness display

• Indicates the “SHARPNESS H/V” setting value of

the “VIDEO CONFIG” menu.

• If no operation is performed for 2 minutes,

the setting value is confirmed and the display

disappears.

SHARPNESS H 30

Function display

• Use the menu to open and set up functions.

• When “FUNCTION DISPLAY” (page 39) is set

to ON1 or ON2, press any of the “FUNCTION1”

to “FUNCTION3” buttons to display the functions

assigned to the FUNCTION buttons.

• In 3D assist mode (page 52), [FUNCTION3]

becomes the 2D picture quality adjustment mode

button.

F1:WFM/VECTOR

F2:PIXEL TO PIXEL

F3:FOCUS-IN-RED

XXXXX

• If no operation is performed for 2 seconds,

the setting value is confirmed and the display

disappears.

• “XXXXX” indicates operating status (page 41,

“Functions displayed during FUNCTION button

operation”).

Download from Www.Somanuals.com. All Manuals Search And Download.

On-screen Display (continued)

Audio level meter display

Reference point

Channel

• A color skeleton bar meter indicates the audio

level for SDI signals and HDMI signals.

• The display method of the audio level meter can

be set in the menu (page 49).

display

0 dB point

• In 3D assist mode, the audio of the SDI1 (L) side

is indicated.

Display color

SDI1 1080/60i

Green: Up to reference point (included)

Yellow: Reference point (not included) to 0 dB point

Red:

Overrange

Peak hold

Overrange

Time code (TC) display

• Use the menu to display the time code for HD-SDI

signal input. It also allows you to switch display

mode (VITC, LTC, VUB, LUB). (page 50)

In VITC and LTC display mode:

• Displays the time code in hours: minutes:

seconds: or frames.

• In drop-frame mode, a different delimiter between

seconds and frames is used.

Note :

( : ) NDF

( . ) DF

Read errors are displayed as “--:--:--:--”

In VUB and LUB display modes:

• BG8, BG7, BG6, BG5, BG4, BG3, BG2, BG1

appear in the stated order.

BG: binary group

• The (:) delimiter does not appear.

Note :

Read errors are displayed as “--:--:--:--”

Download from Www.Somanuals.com. All Manuals Search And Download.

On-screen Display (continued)

Closed caption (CC) display

• CLOSED CAPTION can be displayed when SDI

signals and VIDEO signals are input.

• CLOSED CAPTION complies with the following

standards.

• Composite Standard EIA/CEA-608 (VBI)

• SD-SDI CC Standard EIA-608 (ANC)

• HD-SDI CC Standard EIA-708

Closed caption

display area

• In the case of EIA-708, display is possible at a

position simultaneously specified for multiple

windows (up to 8).

• The display position is within a display area that

is located inside the entire screen. (Refer to the

following notes.)

• The display settings can be configured in the menus.

You can also select the type of CLOSED CAPTION,

display channel (EIA/CEA-608), and display service

(EIA/CEA-708) in the menus. (page 50)

Notes:

• The specified window position is displayed as a

position within the display area depending on the

CLOSED CAPTION information.

Closed caption

display area

• The window may extend out of the display area

depending on the specified window position and

size. In such a case, the window will be displayed

but if the window also extends out of the entire

screen, the display position of the window will be

changed so that the window is displayed inside

the entire screen.

(When the specified

window extends out of

the entire screen)

DC power supply voltage and battery level display

• DC power supply voltage is displayed.

• The battery level display is displayed when the

battery you are using is an Anton/Bauer battery

with a battery level display function.

• Displayed when the operating status display is not

displayed.

• The display can be set in the menus. (page 34)

Notes:

• The DC power voltage and battery level serve

as a near end warning indication as they flash

when the level falls to the value set in the menu or

lower.

DC14.0V

50%

Furthermore, when the level drops to less than

approximately 10.0 V, the “END BATTERY”

battery level error is displayed in red, and

the unit performs the shutdown process after

approximately 3 seconds have elapsed.

• With some batteries, operation may be stopped

by an over discharge function of the battery

itself before the battery level error of the unit is

displayed.

We recommend replacing the battery as soon as

possible.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Use the On Screen Menu

Menu display

• This is the menu display.

[MAIN MENU]

2D/3D ASSIST

• The menu display disappears after 2 minutes of

inaction. (The setting values that were displayed

at the time that the menu display disappeared are

applied.)

MARKER

VIDEO CONFIG

SYSTEM CONFIG

VF CONFIG

FUNCTION

GPI

INPUT SELECT

DISPLAY SETUP

CONTROL

HOURS METER

MENU EXIT

SEL. ENTER ENTER

Displays the operation explanation for the

menu button.

Menu operations

1. Press [MENU] to display the MAIN menu.

3. Press [ ][ ] to select a sub menu and press

[ENTER].

The settings in the sub menu change to green.

FUNCTION

[MARKER]

MARKER

OFF

4:3

16:9

4:3

OFF

BACK

NORMAL

OFF

INPUT MENU

ENTER

CENTER

GPI MARKER1

GPI MARKER2

MARKER TYPE

CROSS HATCH

SIZE

95%(16:9)

TYPE 1

OFF

MENU EXIT

SEL. ENTER ENTER

2. Press [ ][ ] to select a menu and press

[ENTER].

4. Press [ ][ ] to select a setting, then press

[ENTER].

To cancel, press [MENU].

[MAIN MENU]

2D/3D ASSIST

MARKER

VIDEO CONFIG

SYSTEM CONFIG

VF CONFIG

[MARKER]

MARKER

4:3

16:9

FUNCTION

GPI

4:3

OFF

INPUT SELECT

DISPLAY SETUP

CONTROL

BACK

NORMAL

OFF

CENTER

GPI MARKER1

GPI MARKER2

MARKER TYPE

CROSS HATCH

SIZE

95%(16:9)

TYPE 1

OFF

HOURS METER

MENU EXIT

SEL. ENTER ENTER

MENU EXIT

SEL. ENTER ENTER

5. To return to the previous screen, press

[MENU].

Download from Www.Somanuals.com. All Manuals Search And Download.

User Data

You can save and load up to five combinations of menu settings and adjustments made with the picture

adjustment knob as user data. You can also return settings and adjustments to their factory defaults. User

data include the following settings.

• Menu settings except “SETUP LOAD/SAVE” and “REMOTE in CONTROL” (including button function

settings on the monitor front panel)

• Screen adjustments made with the picture adjusting knob

Saving user data

Loading user data

1. Press [MENU] to display the MAIN menu.

2. Press [ ][ ] to select the “SYSTEM CONFIG”

menu and press [ENTER].

1. Press [MENU] to display the MAIN menu.

2. Press [ ][ ] to select the “SYSTEM CONFIG”

menu and press [ENTER].

3. Press [ ][ ] to select the “SETUP SAVE”

sub menu and press [ENTER].

3. Press [ ][ ] to select the “SETUP LOAD”

sub menu and press [ENTER].

The setting in the sub menu changes to green.

[SYSTEM CONFIG]

SUB WINDOW

FULL

CENTER

3SEC OFF

OFF

SUB WINDOW

FULL

CENTER

3SEC OFF

OFF

MENU POSITION

STATUS DISPLAY

BATTERY REMAIN

WARNING VOLTAGE

SETUP LOAD

MENU POSITION

STATUS DISPLAY

BATTERY REMAIN

WARNING VOLTAGE

SETUP LOAD

TYPE1

FACTORY

USER1

LAST

TYPE1

FACTORY

USER1

LAST

SETUP SAVE

POWER ON SETUP

COLOR SPACE

POWER SAVE MODE

CALIBRATION

POWER ON SETUP

COLOR SPACE

POWER SAVE MODE

CALIBRATION

EBU

OFF

▼

AREA SETTING

NTSC

AREA SETTING

NTSC

MENU EXIT

SEL. ENTER ENTER

MENU EXIT

SEL. ENTER ENTER

Changes to green

4. Press [ ][ ] to select a “USER1” to “USER5”

file to load and press [ENTER].

The following screen appears.

• To return to the factory defaults, select

“FACTORY.”

4. Press [ ][ ] to select a “USER1” to “USER5”

file to save the settings to and press [ENTER].

The following screen appears.

[

]

SETUP SAVE

[

]

SETUP LOAD

USER1

YES

USER1

YES

MENU EXIT

SEL. ENTER ENTER

MENU EXIT

SEL. ENTER ENTER

5. Select “YES”, and press [ENTER].

This saves the user data.

5. Select “YES”, and press [ENTER].

This loads the user data.

6. To return to the previous screen, press

[MENU].

6. To return to the previous screen, press

[MENU].

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu

Menu configuration

MAIN MENU

2D/3D ASSIST

MARKER

16:9

VIDEO CONFIG

SYSTEM CONFIG

GAMMA SELECT

FILM GAMMA

COLOR TEMP.

SHARPNESS MODE

SHARPNESS H

SHARPNESS V

I-P MODE

4:3

BACK

SUB WINDOW

CENTER

GPI MARKER1

GPI MARKER2

MARKER TYPE

CROSS HATCH

SIZE

MENU POSITION

STATUS DISPLAY

BATTERY REMAIN

WARNING VOLTAGE

SETUP LOAD

MONO

SETUP SAVE

ANAMO

USER0-63

D93

POWER ON SETUP

COLOR SPACE

POWER SAVE MODE

CALIBRATION

SD ASPECT

SCAN

D65

WHITE BALANCE

D56

VAR1

VAR2

VAR3

AUTO CALIBRATION

RESET

COLOR TEMP.

GAIN

AREA SETTING

RED

GREEN

BLUE

VF CONTROL

REAR TALLY

ZEBRA

VF CONFIG

FUNCTION

BIAS

FUNCTION1

GPI CONTROL

GPI1

RED

FUNCTION2

GREEN

BLUE

FUNCTION3

GPI2

FUNCTION DISPLAY

GPI3

RESET

GPI4

GPI

GPI5

GPI6

INPUT SELECT

VIDEO

GPI7

FORMAT

NTSC SETUP

GPI8

SELECT L

SDI1

SDI2

SELECT R

LEVEL METER

CH SELECT

POINT LINE

CH INFO.

HDMI

YP_BP_R

COMPONENT LEVEL

HEAD ROOM

AUDIO

WFM/VECTOR

POSITION

VIDEO/ YP_BP_R

SIGNAL TYPE

INT SG

VECTOR MODE

VECTOR SCALE

DISPLAY SETUP

CONTROL

TIME CODE

MODE SELECT

CLOSED CAPTION

CONTROL

LOCAL ENABLE

CC TYPE

CAPTION CHANNEL

CAPTION SERVICE

OPERATION

LCD

HOURS METER

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

2D/3D ASSIST

The underlined values are factory preset setting values.

Setting

Description

Switches between 2D mode and 3D assist mode.

<2D> Operates in 2D mode.

<3D ASSIST> Operates in 3D assist mode.

If you switch to 3D assist mode, the channel setting is forcefully

3D ASSIST

switched to SDI1 (SDI2).

Use knob 4 to switch between each of the assist functions. (page

52)

MARKER

The underlined values are factory preset setting values.

Description

Sub menu

Settings

OFF

MARKER

Enables the MARKER setting.

* *

16:9

OFF

4:3

Selects/displays the marker type for when the angle of view of

the displayed image is 16:9.

13:9

<OFF> No marker display

14:9

<4:3>

4:3 marker

CNSCO 2.39

CNSCO 2.35

2:1

VISTA

95%

<13:9> 13:9 marker

<14:9> 14:9 marker

<CNSCO 2.39> 2.39:1 marker

<CNSCO 2.35> 2.35:1 marker

<2:1>

2:1 marker

93%

<VISTA> VISTA marker

90%

<95%> 95 % area marker

88%

<90%> 90 % area marker

80%

<80%> 80 % area marker

USER 85%

<93%> 93.1 % area marker (TYPE1)

93 % area marker (TYPE2)

<88%> 89.5 % area marker (TYPE1)

88 % area marker (TYPE2)

<USER> Area marker that is adjustable in 1 % increments within

a range of 80 % to 100 %. However, when MARKER

TYPE is TYPE1, 88 % becomes the aspect ratio of the

vertical 89 %.

(The factory preset setting value is 85 %.)

(Continued on next page)

This setting is turned “ON” when receiving marker control in REMOTE operation. (GPI, if set, has

priority.)

These settings are disabled when the GPI function (page 62) is used to control the marker setting.

These settings are enabled when the SD aspect setting for an HD signal and SD signal is 16:9 ( “SD

ASPECT” on page 31).

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

Sub menu

Settings

Description

* *

4:3

OFF

95%

Selects/displays the marker type for when the angle of view of

the displayed image is 4:3.

93%

<OFF> No marker display

90%

<95%> 95 % area marker

88%

<93%> 93 % area marker

80%

<90%> 90 % area marker

USER 85%

<88%> 89 % area marker (TYPE1)

88 % area marker (TYPE2)

<80%> 80 % area marker

<USER> Area marker that is adjustable in 1 % increments within

a range of 80 % to 100 %. However, when MARKER

TYPE is TYPE1, 93 % becomes the aspect ratio of

the vertical 93.1 %, and 88 % the aspect ratio of the

vertical 89 %.

(The factory preset setting value is 85 %.)

BACK

NORMAL

HALF

Selects the background brightness around the marker.

<NORMAL> Normal background

BLACK

<HALF>

50 % background brightness

<BLACK>

0 % background brightness (black)

CENTER

OFF

Displays the center marker.

<OFF>

<ON>

Turns the display off

Turns the display on

(Continued on next page)

These settings are disabled when the GPI function (page 62) is used to control the marker setting.

These settings are enabled when the SD aspect setting for an SD signal is 4:3 (→ “SD ASPECT” on

page 31).

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

Sub menu

Settings

Description

GPI MARKER1

4:3

13:9

14:9

GPI MARKER1 : Selects the marker displayed by the GPI

terminal “MARKER1 ON/OFF” (page 62)

operation.

CNSCO 2.39

CNSCO 2.35

2:1

GPI MARKER2 : Selects the marker displayed by the GPI

terminal “MARKER2 ON/OFF” (page 62)

operation.

GPI MARKER2

VISTA

<4:3>

<13:9>

<14:9>

4:3 marker

13:9 marker

14:9 marker

95% (16:9)

93% (16:9)

90% (16:9)

88% (16:9)

80% (16:9)

USER(16:9)

95% (4:3)

93% (4:3)

90% (4:3)

88% (4:3)

80% (4:3)

USER(4:3)

<CNSCO 2.39> 2.39:1 marker

<CNSCO 2.35> 2.35:1 marker

<2:1>

2:1 marker

<VISTA>

VISTA marker

<95% (16:9) >

<93% (16:9) >

<90% (16:9) >

<88% (16:9) >

<80% (16:9) >

95% area marker for 16:9 aspect ratio

93% area marker for 16:9 aspect ratio

90% area marker for 16:9 aspect ratio

88% area marker for 16:9 aspect ratio

80% area marker for 16:9 aspect ratio

<USER (16:9) > User settings area marker for 16:9 aspect ratio

<95% (4:3) >

<93% (4:3) >

<90% (4:3) >

<88% (4:3) >

<80% (4:3) >

95% area marker for 4:3 aspect ratio

93% area marker for 4:3 aspect ratio

90% area marker for 4:3 aspect ratio

88% area marker for 4:3 aspect ratio

80% area marker for 4:3 aspect ratio

User settings area marker for 4:3 aspect ratio

MARKER TYPE

CROSS HATCH

TYPE1

TYPE2

Selects conventional monitor or camera recorder marker size.

<TYPE1> Conventional monitor marker size

<TYPE2> Marker size compliant with the camera recorder

(Panasonic made)

HIGH

LOW

OFF

Turns the cross hatch grid on and off and sets its density.

<HIGH>

<LOW>

<OFF>

Displays a bright cross hatch grid

Displays a dim cross hatch grid

Turns the display off

SIZE

Selects the cross hatch grid size.

<80>

<40>

80 dots and 80 lines

40 dots and 40 lines

Remote control via RS-232C ends in error (error response: ER001) when “GPI MARKER1” or “GPI

MARKER2”is selected with the GPI function.

Display size for SD signals differ.

TYPE1: The effective horizontal area meets the SMPTE125M for NTSC and ITU-R BT. 601-5 for PAL.

TYPE2: The effective horizontal area meets the EIA-RS170A for NTSC and ITU-R BT. 470-4 for PAL.

<Notes>

• The marker is not displayed during 2-screen display (SUB WINDOW), PIXEL TO PIXEL mode, and 3D

assist mode.

• The marker is not displayed during VF line operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

Types of MARKER

■

16:9 marker

(Displayed when using HD, or when using SD with a 16:9 aspect ratio)

The marker is only displayed as a vertical bar. In addition, the

item.

section becomes the “MARKER BACK”

4:3 marker

13:9 marker

14:9 marker

VISTA marker, 2:1 marker, CNSCO marker

A horizontal dotted line is displayed as the marker.

VISTA marker

2:1 marker

CNSCO marker

(2.35/2.39)

The marker is displayed as a vertical dotted line when “UNDER” is selected under “SCAN” in the “VIDEO

CONFIG” menu.

VISTA marker

2:1 marker

CNSCO marker

(2.35/2.39)

Area marker

A dotted line is displayed as the marker.

TYPE1 Vertical 93.1 %

horizontal 93 %

TYPE2 Vertical/Horizontal 93 %

95 % Area marker

93 % Area marker

90 % Area marker

95 % Area marker

TYPE1 Vertical 89.5 %

Horizontal 88 %

TYPE2 Vertical/Horizontal 88 %

88 % Area marker

80 % Area marker

USER Area marker

You can adjust the value within the range of 80 % to 100 % in increments of 1 % by pressing [ ][ ].

(Continued on next page)

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

4:3 marker

(Displayed for SD input in 4:3 aspect ratio mode)

This marker is displayed as a dotted line.

95 % Area marker

88 % Area marker

93 % Area marker

80 % Area marker

90 % Area marker

(Displayed for HD input and SD input in 16:9 ratio mode.)

This marker is displayed as a dotted line.

95 % Area marker

93 % Area marker

90 % Area marker

TYPE1 Vertical 89 %

Horizontal 88 %

95 % Area marker

TYPE2 Vertical/Horizontal 88 %

88 % Area marker

80 % Area marker

USER Area marker

You can adjust the value within the range of 80 % to 100 % in increments of 1 % by pressing [ ][ ].

You can display the 4:3 marker and the 16:9 marker simultaneously.

Simultaneous display example

The

section becomes the “MARKER BACK”.

It controls the background of the marker selected with a 16:9 ratio.

16:9 marker : 95 % area marker

4:3 marker : 80 % area marker

4:3 marker

16:9 marker

■

Center marker

This marker is displayed at the center of the screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

VIDEO CONFIG

The underlined values are factory preset setting values.

Description

Sub menu

Settings

GAMMA

SELECT

STANDARD

FILM

STDIO/PST

Selects gamma curve.

<STANDARD> Standard mode

<FILM>

Film mode

<STDIO/PST> Color emphasis mode (a mode that

approximates CRT display capability suitable

for studio or postproduction application)

When FILM is selected, the

operating status.

mark is displayed for the

FILM GAMMA

VARICAM

OTHER

Selects type of FILM gamma mode.

<OTHER>

For VARICAM use

Other

(Gamma curve image)

OTHER

Video Gamma

VARICAM

Input Level

Selects color temperature.

<USER 0 - 63> Adjustable settings 0 - 63

(equivalent to a color temperature range of

COLOR TEMP.

USER 0 - 63

D93

D65

D56

3,000 K - 9,300 K)

VAR1

VAR2

VAR3

<D93>

<D65>

<D56>

Equivalent to a color temperature of 9,300 K

Equivalent to a color temperature of 6,500 K

Equivalent to a color temperature of 5,600 K

<VAR1> WB adjustment mode

<VAR2> WB adjustment mode

<VAR3> WB adjustment mode

(Continued on next page)

In split-screen display, changes are not reflected to the still image in the main window.

When selecting USER 0 - 63

1) Push [ENTER] (USER changes to blue).

2) Select 0 - 63 with [ ], [ ] and push [ENTER].

Selecting “VAR1”, “VAR2” and “VAR3” engages the WB adjustment mode (page 32).

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

Sub menu

Settings

Description

SHARPNESS

MODE *⁴

HIGH

LOW

Selects the width of outline correction edge.

<HIGH> Narrow edge

<LOW> Wide edge

SHARPNESS H *⁴0 - 30

Sets horizontal outline correction. The item display moves to

the lower part of the screen during adjustment.

SHARPNESS V *⁴0 - 30

Sets vertical outline correction. The item display moves to the

lower part of the screen during adjustment.

I-P MODE

MONO

MODE2

MODE1

Selects IP conversion mode. (see “IP mode” below.)

<MODE2> Intra-field interpolation

<MODE1> Intra-frame interpolation

OFF

Switches between color and monochrome (MONO).

<OFF> Color

<ON>

Monochrome

When ON, the CHROMA setting of the picture adjusting knob

is fixed at 0.

ANAMO

OFF

With an Anamo lens and HD-SDI input, the picture is resized

to Anamo magnification (the vertically enlarged signal can be

vertically compressed and corrected for display).

SD ASPECT

4:3

16:9

Sets the aspect ratio for SD signal input.

<4:3> 4:3 display

<16:9> 16:9 display

SCAN

NORMAL

UNDER

Sets under-scan and normal display.

<NORMAL> Normal display

<UNDER> Under-scan

The following sharpness values are available and the settings for the selected input signal is displayed.

Adjustment status during selection appears at the bottom left of the screen.

1) VIDEO system input (VIDEO) (the factory defaults are SHARPNESS MODE: LOW and SHARPNESS

H/V: 0)

2) HD for any other input (the factory defaults are SHARPNESS MODE: HIGH and SHARPNESS H/V: 0).

3) SD for any other input (the factory defaults are SHARPNESS MODE: LOW and SHARPNESS H/V: 0).

To use the “SUB WINDOW” (page 42) function,

1) Change settings after exiting the “SUB WINDOW” function.

2) It is recommended to use “MODE2” for handling fast video.

“SCAN” changes are not reflected in Anamo size display.

IP mode

“MODE1” performs IP conversion using intra-frame interpolation.

This monitor suppresses the delay to within 1 field.

The factory default is “MODE1”.

“MODE2” performs IP conversion using intra-field interpolation.

Since interpolation is performed inside each field, this mode is suitable for checking interlace status.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

WB (WHITE BALANCE) adjustment mode

Select “VAR1” to “VAR3” for “COLOR TEMP.” in the “VIDEO CONFIG” menu to make “WHITE BALANCE

VAR1” to “WHITE BALANCE VAR3” (WB) adjustments.

The underlined values are factory preset setting values.

Sub menu

COLOR TEMP.

Settings

Description

USER 0 - 63

D93

Selects the color temperature that will become the basis

for adjustment.

D65

D56

Adjustable settings 0 - 63 (equivalent

to a color temperature range of

3,000 K - 9,300 K)

<D93> Equivalent to a color temperature of 9,300 K

<D65> Equivalent to a color temperature of 6,500 K

<D56> Equivalent to a color temperature of 5,600 K

GAIN

▼

Adjusts the GAIN elements

Press [ENTER] to switch to RGB direct adjustment mode.

(This allows you to begin adjusting GAIN first.)

RED

0 - 1023

Adjusts the GAIN elements for RED. (For numerical value

confirmation)

(Factory defaults are

color temperature

<D65> values.)

*These are the

adjustments made

before shipment from

the factory.

GREEN

BLUE

Adjusts the GAIN elements for GREEN. (For numerical

value confirmation)

Adjusts the GAIN elements for BLUE. (For numerical

value confirmation)

BIAS

▼

Adjusts the BIAS elements

[Press [ENTER] to switch to RGB direct adjustment

mode.

(This allows you to begin adjusting BIAS first.)

RED

GREEN

BLUE

- 512 - 511

(Factory default: 0)

Adjusts the BIAS elements for RED. (For numerical value

confirmation)

Adjusts the BIAS elements for GREEN. (For numerical

value confirmation)

Adjusts the BIAS elements for BLUE. (For numerical

value confirmation)

RESET

▼

Resets “GAIN RED” - “BIAS BLUE” to color temperature

values selected under “COLOR TEMP.”

Selecting “COLOR TEMP.” and pressing [ENTER] after making a change, opens a confirmation screen.

Selecting “YES” and pressing [ENTER] in this screen resets selected GAIN and BIAS values to the

selected color temperature values.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

GAIN/BIAS RGB direct adjustment mode

If you press [ENTER] when the [GAIN] or [BIAS] item is selected in the WHITE BALANCE VAR (1 to 3)

menu, the screen switches to the one below and you can use the picture adjusting knobs to directly adjust

the RGB while checking the picture.

R is assigned to knob 1, G to knob 2, and B to knob 3.

If “WHITE BALANCE” is assigned to FUNCTION1 to FUNCTION3, this mode can also be accessed from

the FUNCTION buttons.

• You can switch between GAIN and BIAS by

pressing the corresponding knob.

• If you press [ENTER] in the [GAIN] menu, GAIN

adjustment is displayed first.

• If you press [ENTER] in the [BIAS] menu, BIAS

adjustment is displayed first.

• When you access the mode from a FUNCTION

button, GAIN adjustment is displayed first.

• The adjustment item name and the numerical

value of the element is displayed above each of

the knobs.

489 511 456

R-GAIN G-GAIN B-GAIN

F-IN-R

PEAK/

PHASE

VOLUME/

BRIGHT

CONT./

CHROMA

B.LIGHT

• Press the [MENU] button to return to menu

display. *¹

• If you switched the mode with a FUNCTION

button, display disappears if you press the

FUNCTION button. *¹

The same operation is also performed after 10

seconds of inaction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

SYSTEM CONFIG

The underlined values are factory preset setting values.

Description

Sub menu

Settings

SUB WINDOW

FULL

PART

Selects sub-window type.

<FULL> Reduces the entire images for both input signals and

places them side by side.

<PART> Cuts out the center of the images for both input signals

and places them side by side (the images are shown at

their original size).

MENU POSITION

CENTER

Positions the on-screen menu.

<CENTER> Center of the screen

<LB>

<RT>

Left Bottom

Right Top

<RB>

<LT>

Right Bottom

Left Top

STATUS

DISPLAY

CONTINUE

3SEC OFF

OFF

Sets the display state of the operating status display (page 18).

<CONTINUE> Displayed at all times

<3SEC OFF>

<OFF>

Displayed for 3 seconds after a status change.

Not displayed.

BATTERY

REMAIN

OFF

Selects whether DC power supply voltage and battery level

display.

<OFF> Not displayed.

<ON>

Displayed.

WARNING

VOLTAGE *³

TYPE1

TYPE2

Sets the near end warning voltage for the battery level display.

<TYPE1> Select this when you will mainly use an external DC

power supply. Near end is approximately 11.3 V.

<TYPE2> Select this when you will mainly use a battery. Near

end is approximately 13.3 V.

SETUP LOAD

USER5

Loads saved factory defaults (FACTORY) or user data (USER1 -

USER5) (page 23) .

After loading user data, the screen displays the signal selected

before user data was loaded.

USER4

USER3

USER2

USER1

FACTORY

SETUP SAVE

USER5

USER4

USER3

USER2

USER1

Up to 5 sets of user data can be saved (page 23).

They save menu settings and adjustments made with the picture

adjusting knob except “SETUP SAVE/SETUP LOAD.”

POWER ON

SETUP

USER5

USER4

USER3

USER2

USER1

FACTORY

LAST

Selects the settings used when the power is turned on.

<LAST>

Starts in the mode used when the power was

last turned off.

Starts up using the factory defaults.

<USER1 - 5> Starts up using USER registered settings.

(Continued on next page)

When PIXEL to PIXEL, operation is with CONTINUE regardless of the setting.

When PIXEL TO PIXEL/3D assist mode, the 3SEC OFF setting becomes equivalent to CONTINUE.

When the BATTERY REMAIN display setting is OFF, near end warning display does not occur.

The settings of USER1 to USER 5 and FACTORY are the same at the time of shipment from the factory.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

Sub menu

Settings

Description

COLOR SPACE

SMPTE-C

EBU

Sets the studio standard color space.

ITU-709

POWER SAVE

MODE

OFF

Sets the power save mode

<ON> The backlight dims when no signal (NO SIGNAL) is input

for 60 seconds or longer. Signal input or menu operation

will return the backlight to its normal brightness.

CALIBRATION

▼

Connect Display Color Analyzer CA-210 and then perform

calibration. This also allows you to restore the calibration data to

the factory preset setting values.

(pages 35, 36, and 37)

AREA SETTING

NTSC

NTSC (J)

PAL

Selects the area of the unit.

(→ “Selecting Area of Use” on page 8)

• The setting does not vary depending on the operation of SETUP

LOAD or POWER ON SETUP.

The factory preset setting value varies depending on the area set in “AREA SETTING”.

ITU-709 indicates the ITU-R BT.709 standard.

■

CALIBRATION

The CALIBRATION function in this unit measures LCD panel characteristics from low to high brightness

values and internal monitor processing handles CALIBRATION.

CALIBRATION does not rely on image quality settings since internal signals are used for a calibration.

CALIBRATION in this unit is made at D65 color temperature and other color temperatures are results

calculated automatically from this value.

■

Equipment required for calibration

• Konica Minolta CA-210

Analyzer Side

(Straight)

This unit Side

or CA-310 display color

analyzer

• Konica Minolta CA-

PU12 or CA-PU15

standard measurement probe

• A RS-232C cable (male to male, straight)

Pin number Signal

N.C.

TXD

RXD

DSR

GND

DTR

CTS

RTS

N.C.

SERIAL Terminal (9P)

RXD

TXD

DTR

GND

DSR

RTS

CTS

GND

Connect the SERIAL terminal on this unit to the RS-

232C terminal on the display color analyzer using a

straight cable.

This unit

Konica Minolta CA-PU12 or CA-PU15

standard measurement probe

Konica Minolta CA-210 or CA-310 display

color analyzer

RS-232C cable

(Continued on next page)

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

• When using the CA-210 display color analyzer,

be sure to set the compensation values shown

on the right. If they are not set, correct calibration

will not be performed. For details on setup

Compensation

0.296

0.6534 0.2851 0.1485

0.3036 0.3271 0.5927 0.0523

203.4 43.18 148.1 15.5

procedures, refer to the CA-210 User's Guide.

• There is no compensation when using Display Color Analyzer CA-310.

• Turn on this unit and perform adequate aging (about 1 hour) before starting calibration.

• Make the room dark so that no external light can enter the standard measurement probe before starting

the calibration. If external light enters the probe, the low brightness characteristics may not be calibrated

correctly.

• LCD panel characteristics and instrument error in the display color analyzer may sometimes result in small

differences in values after calibration.

In a fine tuning of the monitor, also set GAIN and BIAS for R, G and B in the COLOR TEMP. VAR mode.

• Do not apply the probe to a WFM/VECTOR display on the screen.

■

CALIBRATION

Select CALIBRATION in the “SYSTEM CONFIG” menu to open the following menus.

Sub menu

Settings

Description

AUTO CALIBRATION

▼

Connect a CA-210 Display color analyzer and use this

submenu to make a calibration.

Select “AUTO CALIBRATION” and select “YES” in the

confirmation screen that appears to start calibration.

RESET

▼

Returns calibration data to their factory defaults.

Select “RESET” and select “YES” in the confirmation screen

that appears to return calibrated values to their factory defaults.

“EXECUTING” is displayed during “AUTO CALIBRATION” and “COMPLETE” appears when calibration

ends. “INCOMPLETE” appears if calibration could not be completed.

When “RESET” ends, “COMPLETE” appears.

Performing AUTO CALIBRATION

1. Press [ ][ ] in the “SYSTEM CONFIG”

menu, select the [CALIBRATION] submenu

and press [ENTER].

3. Select “YES” and press [ENTER].

This starts calibration.

[AUTO CALIBRATION]

xxxxxxxx

2. Press [ ][ ], select the [AUTO

CALIBRATION] submenu and press [ENTER].

[AUTO CALIBRATION]

YES

MENU EXIT

SEL. ENTER ENTER

xxxxxxxxx indicates that one of the following

messages with the meaning listed below

appears.

MENU EXIT

SEL. ENTER ENTER

EXECUTING: Operation in progress

COMPLETE: Operation completed

INCOMPLETE: Operation incompleted.

(Check the SERIAL connection or display color

analyzer connection.)

4. Turn the power off and then on after

performing auto calibration.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

RESET operation

1. Press [ ][ ] in the “SYSTEM CONFIG”

menu, select the [CALIBRATION] submenu

and press [ENTER].

3. Select “YES” and press [ENTER].

This starts calibration.

2. Press [ ][ ], select the [RESET] submenu

[RESET]

and press [ENTER].

xxxxxxxx

[RESET]

YES

MENU EXIT

SEL. ENTER ENTER

xxxxxxxxx indicates that the following message

with the meaning listed below appears.

COMPLETE: Operation completed

MENU EXIT

SEL. ENTER ENTER

4. Turn the power off and then on after

performing auto calibration.

VF CONFIG

The underlined values are factory preset setting values.

Sub menu

Settings

Description

Used to select the input line for the VF function of the monitor.

VF CONTROL

VF-CH

ALL-CH

(VF function: tally lamps (red and green) lit, zebra displayed,

displayed, aspect changed [SD])

<VF-CH>

Only enabled when the VF line is selected.

<ALL-CH> Enabled with all input lines.

REAR TALLY

ZEBRA

OFF

Used to allow control of the tally lamp on the rear of the monitor.

<OFF> Does not light.

<ON> Lights when TALLY control from a GPI/camera is ON.

OFF

Used to set ZEBRA information in the camera.

<OFF> Sets the information to OFF.

<ON> Sets the information to ON.

• The priority sequence for GPI control and SERIAL is as follows: GPI > VF CONFIG > SERIAL.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

FUNCTION

The underlined values are factory preset setting values.

Description

Sub menu

Settings

FUNCTION 1 -

FUNCTION 3

HV DELAY

Selects functions to be assigned to [FUNCTION1] -

[FUNCTION3] (front panel buttons).

BLUE ONLY

GAMMA SELECT

SD ASPECT

SCAN

SUB WINDOW

WFM/VECTOR

MARKER

WHITE BALANCE

PIXEL TO PIXEL

PIXEL POSITION

FOCUS-IN-RED

ZEBRA

Displays the image blanking period.

The display changes in the following order.

DELAY OFF → H DELAY → V DELAY → HV DELAY →

DELAY OFF

Cuts the red and green signals. Use this function to check

phase and chroma. This button toggles between ON and

OFF.

* *

Displays the gamma curve.

REAR TALLY

LEVEL METER

CROSS HATCH

MONO

BLACK MODE

TIME CODE

CLOSED CAPTION

UNDEF

The display changes in the following order.

GAMMA STANDARD → GAMMA FILM →

GAMMA STDIO/PST → GAMMA STANDARD

* *

Switches between “16:9” and “4:3.”

<SCAN>

* *

Switches between “UNDER SCAN” and “NORMAL SCAN”.

Sets the split-screen function.

The display changes in the following order.

SINGLE → FULL/PART → STILL → SINGLE

(Factory default:

FUNCTION1:

WFM/VECTOR

FUNCTION2:

PIXEL TO PIXEL

FUNCTION3:

FOCUS-IN-RED)

Displays waveform or vector display.

For details on the available operation items, refer to page

41.

* * *

Turns the marker on and off.

For details on the available operation items, refer to page

41.

WHITE BALANCE GAIN/BIAS RGB direct adjustment can

only be accessed when VAR1 to VAR3 are selected in

COLOR TEMP.

Turns the PIXEL TO PIXEL function On and Off.

Positions the display of signals in PIXEL TO PIXEL mode.

(Continued on next page)

The settings are cancelled when the power is turned OFF.

If these settings are changed, the menu settings will also change.

The control settings do not operate during GPI operation.

Not displayed when 16:9, 4:3 and CENTER are all OFF in the MARKER menu settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

Sub menu

Settings

Description

(From the

previous page)

<FOCUS-IN-RED>

* *

Used to highlight in red the section of the image that is being

focused.

<ZEBRA>

Used to set the zebra display ON or OFF for the camera.

* *

Used to set the rear tally ON or OFF.

Turns the AUDIO LEVEL METER display On and Off.

Displays the cross hatch grid.

The display changes in the following order.

CROSS HATCH OFF → CROSS HATCH LOW →

CROSS HATCH HIGH

<MONO>

* *

Switches between color and monochrome.

* *

This mode is for reducing floating black and checking the

gradation of dark sections.

The brightness of the backlight is reduced and the contrast is

increased so that up to 75 % of the input signal level has the

same gamma curve as the set GAMMA SELECT. The signal

level on or above that is clipped at 75 %.

Turns the time code display on and off.

Turns the closed caption display on and off.

For details on the available operation items, refer to page 41.

<UNDEF>

Undefined

FUNCTION

DISPLAY

OFF

ON1

ON2

Selects display of functions assigned to [FUNCTION1] -

[FUNCTION3] (front panel buttons). It also selects button action

(1- touch, 2-touch, off).

<OFF> No function display.

<ON1> 1-touch action to display and perform functions.

<ON2> 2-touch action to display and perform functions.

• If a FUNCTION button is pushed during the picture adjusting knobs display, the picture adjusting knobs

display will be cancelled and the FUNCTION operation cannot be executed.

The settings are cancelled when the power is turned OFF.

If these settings are changed, the menu settings will also change.

The control settings do not operate during GPI operation.

During FOCUS-IN-RED operation, the detection sensitivity can be changed with the F-IN-R knob. The

setting range is from 0 to 30, with a higher numerical value resulting in higher detection sensitivity (the

focus becomes worse).

Only enabled when TALLY control from the camera or GPI (R-TALLY) is ON.

The bright picture more than 75 % is clipped. The back light and contrast cannot be adjusted.

The operating status is displayed regardless of the ON/OFF setting.

The function displayed with the ON2 setting can be operated with a button only during the time that it is

displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

FUNCTION setting restrictions

Under the following conditions, “INVALID FUNCTION” is displayed and the settings cannot be configured.

Settings

Inoperable Condition or Mode

HV DELAY

• SUB WINDOW

• WFM

• PIXEL TO PIXEL

• 3D ASSIST

• When HDMI (640 x 480) input

GAMMA SELECT

SD ASPECT

• When GPI is set

• When HDMI (640 x 480) input

• When GPI is set

• SUB WINDOW (Still image)

• 3D ASSIST

• When HDMI (640 x 480) input

SCAN

• When GPI is set

• SUB WINDOW

• PIXEL TO PIXEL

• 3D ASSIST

• When HDMI (640 x 480) input

SUB WINDOW

WFM/VECTOR

• 3D ASSIST

• When HDMI (640 x 480) input

(VECTOR is not displayed when other than SDI1 or SDI2 input)

• SUB WINDOW

• PIXEL TO PIXEL

• 3D ASSIST

• When HDMI (640 x 480) input

MARKER

• When GPI is set

• SUB WINDOW

• 3D ASSIST

• When HDMI (640 x 480) input

WHITE BALANCE

PIXEL TO PIXEL

When other than VAR1 to VAR3 selected in COLOR TEMP.

(Enabled when 1080i/p signal input)

• When other than 1080i/p signal input

• SUB WINDOW

• 3D ASSIST

FOCUS-IN-RED

• When WFM is ON

• When GPI is set

• When INT-SG is selected

LEVEL METER

MONO

When other than SDI1, SDI2, or HDMI input

• When GPI is set

• When HDMI (640 x 480) input

TIMECODE

When other than HD-SDI input

CLOSED CAPTION

• When HDMI (640 x 480) input

• When VF signal input

• When YP_BP_Rsignal input

• 3D ASSIST

• The function assigned to FUNCTION3 does not work when you operate the unit in 3D assist mode

because the FUNCTION3 button becomes specifically for switching to 2D picture adjustment mode (2D

ADJUST).

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

Functions displayed during FUNCTION button operation

Pressing any of the [FUNCTION1] to [FUNCTION3] buttons displays the operations assigned to each

button as shown below.

• HV DELAY

• PIXEL POSITION

DELAY OFF/H DELAY/V DELAY/

HV DELAY

PIXEL TO PIXEL OFF/

PIXEL TO PIXEL CENTER/

PIXEL TO PIXEL LT/

PIXEL TO PIXEL RT/

PIXEL TO PIXEL RB/

PIXEL TO PIXEL LB

• BLUE ONLY

BLUE ONLY ON/BLUE ONLY OFF

• GAMMA SELECT

GAMMA STANDARD/GAMMA FILM/

GAMMA STDIO/PST

• FOCUS-IN-RED

FOCUS-IN-RED OFF/FOCUS-IN-RED ON

• SD ASPECT

4:3/16:9

• ZEBRA

ZEBRA OFF/ZEBRA ON

• SCAN

• REAR TALLY

REAR TALLY OFF/ REAR TALLY ON

NORMAL SCAN/UNDER SCAN

• SUB WINDOW

SINGLE/FULL/PART/STILL

• LEVEL METER

METER OFF/METER 2CH/METER 4CH/

METER 8CH

• WFM/VECTOR

WFM/VECTOR OFF/WFM Y ON/

WFM R ON/WFM G ON/WFM B ON/

VECTOR×1/VECTOR×2S/VECTOR×2/

VECTOR×4/VECTOR×8

• CROSS HATCH

CROSS HATCH HIGH/

CROSS HATCH LOW/

CROSS HATCH OFF

• MARKER

• MONO

MONO ON/MONO OFF

MARKER OFF/4:3 MARKER/

13:9 MARKER/14:9 MARKER/

CNSCO2.39 MARKER/

• TIME CODE

CNSCO2.35 MARKER/

LTC/VITC/LUB/VUB/TC OFF

2:1 MARKER/VISTA MARKER/

95% MARKER/93% MARKER/

90% MARKER/88% MARKER/

80% MARKER/

• BLACK MODE

BLACK MODE OFF/BLACK MODE ON

• CLOSED CAPTION

CC1/CC2/CC3/CC4/CC OFF

(SRV1/SRV2/SRV3/SRV4/SRV5/

SRV6/CC OFF)

* The displayed items differ depending on the

selection for CC TYPE.

xx% MARKER (xx % is a USER setting value of

80 % to 100 %)/MARKER ON

• When the setting values of both 16:9 and 4:3

are set to other than OFF in the MARKER

menu settings, the setting value of 16:9 is

displayed in the first half section, and the

setting value of 4:3 is displayed in the second

half section.

• 2D ADJUST

2D ADJUST OFF/2D ADJUST ON

• PIXEL TO PIXEL

<Note>

PIXEL TO PIXEL OFF/

PIXEL TO PIXEL CENTER/

PIXEL TO PIXEL LT/

PIXEL TO PIXEL RT/

PIXEL TO PIXEL RB/

PIXEL TO PIXEL LB

WHITE BALANCE is switched to adjustment mode

with a FUNCTION button, and the indication that

indicates the operation is not displayed.

■ “HV DELAY”

This displays the blanking period. Each press of the button changes the display as follows: H blanking

display → V blanking display → H and V blanking display → no blanking display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

“SUB WINDOW”

Opening the “SUB WINDOW” function splits the screen (main window) in two as shown below to enable

comparison of a recorded still image with live video.

Use the “SUB WINDOW” setting (FULL, PART) in the “SYSTEM CONFIG” menu (page 34) to set up the

function as shown below.

Press the button ([FUNCTION1] to [FUNCTION3] (page 38)) to which the “SUB WINDOW” function has

been assigned to turn the function on and off.

• This assumes that the “SUB WINDOW” function has been assigned to any of the [FUNCTION1] to

[FUNCTION3] buttons.

To setup “I-P MODE” (page 31), exit the “SUB WINDOW” function first.

• FULL

Resizes the main window to also display a second window (two sub-windows).

Press the FUNCTION button to which the SUB WINDOW function has been assigned.

Normal window

(main window)

Before memory

(two sub-windows)

After memory

(two sub-windows)

Press the

button again

Video

Still image

Video

(Left side is stored

in memory.)

• PART

Resizes the main window to show only its center to also display a second image (two sub-windows).

Press the FUNCTION button to which the SUB WINDOW function has been assigned.

Normal window

(main window)

Before memory

(two sub-windows)

After memory

(two sub-windows)

Press the

button again

Video

Still image

Video

(Left side is stored

in memory.)

Crops the image to show its

center part

The cropped main window

image is placed side by side

with a second image

These examples show 16:9 aspect ratio images.

Note on FULL/PART selection

This function is designed to enable comparison of identical formats input to the same input terminal. Input

of different formats via different input channels may distort the sub-window (left side, still image) or blanking

could occur. However, input of an identical format signal to the input terminal during still image acquisition

will display correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

“WFM/VECTOR”

The “WFM/VECTOR” function enables display of the waveform and vector display. Use “DISPLAY

SETUP” in the main menu to select “WFM” and “VECTOR” display. (page 50)

Press the button ([FUNCTION1] to [FUNCTION3] (page 39)) to which the “WFM/VECTOR” function has

been assigned to switch the display in the following order.

WFM/VECTOR OFF → WFM Y ON → WFM R ON → WFM G ON → WFM B ON → VECTOR (x1 to x8)

• This assumes that the “WFM/VECTOR” function has been assigned to any of the [FUNCTION1] to

[FUNCTION3] buttons.

WFM is displayed in the order of the Y signal, R signal, G signal, and B signal.

Press the FUNCTION button to which the WFM/VECTOR function has been assigned.

WFM display

(Y→R→G→B)

Normal screen

VECTOR display

Press the

button again

WFM

(waveform display)

VECTOR

(vector display)

These examples show 16:9 aspect ratio images.

Displayed only for SDI signal input.

• The scale display is as shown below.

This dotted line is 109%.

100 %

A dotted line indicates for

each 10% increase.

50 %

0 %

This dotted line is -4%.

I axis

The frame is ±2.5°, ±2.5 %

Q axis

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

“PIXEL TO PIXEL” and “PIXEL POSITION”

The “PIXEL TO PIXEL” function allows you to check images at their actual pixel resolution (1080i/p

signals only).

Press the button ([FUNCTION1] to [FUNCTION3] (page 38)) to which the “PIXEL TO PIXEL” function has

been assigned to turn the function on. Then press the button ([FUNCTION1] to [FUNCTION3] (page 38))

to which the “PIXEL POSITION” function has been assigned to position the display of signals.

• This assumes that the “PIXEL TO PIXEL” and “PIXEL POSITION” functions have been assigned to any

of the [FUNCTION1] to [FUNCTION3] buttons.

The underlined values are factory preset setting values.

Item

PIXEL TO PIXEL

Settings

Description

* *

OFF

Sets whether to display the screen display size at the

input signal size.

<OFF> Not displayed.

Compatible formats

<ON> Displayed.

1080/60i/59i/50i/60p/59p/50p/30p/29p/

25p/24p/23p/25PsF/24PsF/23PsF

PIXEL POSITION

CENTER

Positions the display of signals in PIXEL TO PIXEL mode.

<CENTER> Center of the screen

<LT>

<RT>

<RB>

<LB>

Left Top

Right Top

Right Bottom

Left Bottom

The following settings are disabled in PIXEL TO PIXEL mode.

• Setting “ANAMO” to “ON”, and setting “SCAN” to “UNDER” in “VIDEO CONFIG”

• Any “HV DELAY” setting in “FUNCTION”

• “MARKER” display

Enabled during “SDI1”, “SDI2”, “HDMI”, “YP_BP_R” and “VF (VF-YP_BP_R)” input.

■

“PIXEL POSITION” display position sequence

PIXEL POSITION:  →  →  →  →  →  .....

 CENTER

 LT (LEFT TOP)

 RT (RIGHT TOP)

 RB (RIGHT BOTTOM)

 LB (LEFT BOTTOM)

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

“CROSS HATCH”

If the CROSS HATCH function is used, markers are displayed at regular vertical and horizontal intervals

to facilitate, for example, easy composition. The marker line width is 1 dot /1 line and the interval is 80

dots/80 lines or 40 dots/40 lines depending on the “SIZE” setting in the MARKER menu (page 27).

Each press of the button (“FUNCTION1” to “FUNCTION3” (page 38)) to which the “CROSS HATCH” has

been assigned turns the function on and off.

• This assumes that the “CROSS HATCH” function has been assigned to any of the [FUNCTION1] to

[FUNCTION3] buttons.

Each press of the FUNCTION button to which the “CROSS HATCH” function is assigned changes

the display as shown.

HD/SD (16:9) mode

Press the

button again

Dim cross hatch

SD (4:3) mode

Bright cross hatch

Press the button again (back to original image without cross hatch)

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

■

“FOCUS-IN-RED”

When the “FOCUS-IN-RED” function is used, the section that is being focused is displayed in an easy-to-

understand red, making camera focus adjustments easy.

Each press of the button (“FUNCTION1” to “FUNCTION3” (page 38)) to which the “FOCUS-IN-RED” has

been assigned turns the function on and off.

• This assumes that the “FOCUS-IN-RED” function has been assigned to any of the [FUNCTION1] to

[FUNCTION3] buttons.

When the “FOCUS-IN-RED” function is displayed, the detection sensitivity level (0 - 30) can be changed

with the F-IN-R knob. A higher numerical value results in lower detection sensitivity (outlines are displayed

in red even when they are not in focus properly).

If you set CHROMA to 0 or assign "MONO" to another function button to switch to monochrome, the focus

will become easier to check.

Push once the FUNCTION button to which the

FOCUS-IN-RED function is assigned.

Normal screen

FOCUS-IN-RED display

Press the

button again

The foreground is

in focus

The outlines in focus are displayed in red

Press the

button again

The background

is in focus

These examples show 16:9 aspect ratio images.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

GPI

“GPI CONTROL” is used to enable and disable GPI functions and assign functions to each of the GPI

terminal pins (page 62).

The underlined values are factory preset setting values.

Sub menu

Settings

Description

GPI CONTROL

DISABLE

ENABLE

Enables and disables GPI functions

<DISABLE> Disabled

Enabled

GPI1 - GPI8

UNDEF

Assigns functions to the GPI control terminal pins.

The same items can be set to each terminal (page

62).

MARKER1 ON/OFF

MARKER2 ON/OFF

MARKER BACK HALF

MARKER BACK BLACK

CENTER MARKER

INPUT SEL. VIDEO

INPUT SEL. SDI1

INPUT SEL. SDI2

INPUT SEL. HDMI

INPUT SEL. YP_BP_R

INPUT SEL. VF

INPUT SEL. INT SG

SD ASPECT

SCAN

R-TALLY

G-TALLY

MONO

GAMMA SEL. FILM

GAMMA SEL. STDIO/PST

PIXEL TO PIXEL

FOCUS-IN-RED

REMOTE STANDBY

Note:

Operation may not be possible depending on the setting conditions.

Example: “SD ASPECT” operation when input signal is HD

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

INPUT SELECT

The underlined values are factory preset setting values.

Sub menu

Settings

Description

VIDEO

OFF

Sets or cancels VIDEO line for the INPUT button.

FORMAT

AUTO

NTSC

PAL

Used to select the format for VIDEO input.

<AUTO> NTSC or PAL is selected automatically.

<NTSC> NTSC

<PAL> PAL

NTSC SETUP

Selects NTSC setup level.

<75>

Select this function when using 7.5 % setup signals.

(Adjusts the interior of the monitor to the 7.5 % setup level

to suit the black level)

<00>

Select this when the signal is at a 0 IRE setup level.

SDI1

OFF

Sets or cancels SDI1 line for the INPUT button.

SDI2

OFF

Sets or cancels SDI2 line for the INPUT button.

HDMI

YP_BP_R

OFF

Sets or cancels HDMI line for the INPUT button.

OFF

Sets or cancels YP_BP_Rline for the INPUT button.

Selects YP_BP_R(component) signal input level.

COMPONENT

LEVEL

SMPTE

B75

B00

<SMPTE> Signal level complies with SMPTE and P_Band P_Rare 0.7

p-p] at 100 % chroma.

[

<B75>

Select this when connecting a Betacam or similar

device with a setup function. (Adjusts the interior of the

monitor to the 7.5 % setup level to suit the black level)

Select this when connecting a Betacam or similar

device without a setup function.

<B00>

OFF

Sets or cancels VF line for the INPUT button.

VIDEO/YP_BP_R

VIDEO

YP_BP_R

Used to select the VF input mode.

<VIDEO> Selects the VIDEO signal.

<YP_BP_R> Selects the YP_BP_R(component) signal.

SIGNAL TYPE

Used to select the signal output from the camera.

<HD>

<SD>

Selects the HD signal.

Selects the SD signal.

INT SG

OFF

Sets or cancels INT SG line for the INPUT button.

All of the seven input lines (VIDEO, SDI1, SDI2, HDMI, YP_BP_R, VF, and INT SG) cannot be set to OFF. If

six of the input lines are set to OFF, the one remaining input line cannot be set to OFF.

“AUTO” is the factory default, but select a specific format when there is risk that the input signal may be

interrupted by outside noise.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

AUDIO

Set the audio output and audio level meter.

The underlined values are factory preset setting values.

Sub menu

Settings

Description

SELECT L

CH1 - CH8

(Factory default: CH1)

Selects embedded audio channel output to

headphones (L).

* *

SELECT R

CH1 - CH8

(Factory default: CH2)

Selects embedded audio channel output to

headphones (R).

* *

LEVEL METER

CH SELECT

OFF

Selects embedded audio level meter

displayed. (page 20)

8CH

4CH

2CH

Selects number of audio level meter

channels.

POINT LINE

CH INFO.

OFF

Switches the 0 dB line displayed on the

meter on and off.

OFF

Switches the channel displayed on the meter

on and off.

HEAD ROOM

12dB

18dB

20dB

Sets the display position of the reference

point in the meter display.

If the input signal is SD when CH5 to CH8 is selected:

The channel can be switched from CH5→CH1, CH6→CH2, CH7→CH3, and CH8→CH4. (The menu

settings remain as is.)

When an HDMI signal is input, the audio of CH1 is output to the headphones (L) regardless of the menu

setting.

When an HDMI signal is input, the audio of CH2 is output to the headphones (R) regardless of the menu

setting.

When an HDMI signal is input, the display becomes 2CH regardless of the menu setting. When an SD-

SDI signal is input, the display becomes 4CH even if 8CH is selected in the menu.

The factory preset setting value varies depending on the area set in “AREA SETTING” (page 35).

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

DISPLAY SETUP

The underlined values are factory preset setting values.

Description

Sub menu

Settings

WFM/VECTOR

OFF

Switches between “WFM/VECTOR” waveform and vector display.

WFM Y

WFM R

WFM G

WFM B

VECTOR

<WFM Y> - <WFM B> Displays waveforms.

Displays vector waveforms.

POSITION

Selects the position for the “WFM/VECTOR” waveform display.

<LB>

<RB>

<RT>

<LT>

Left Bottom

Right Bottom

Right Top

Left Top

VECTOR MODE

× 8

× 4

× 2

× 2S

× 1

Enlarges vector waveforms.

< × 8>

< × 4>

< × 2>

8 ×

4 ×

2 ×

< × 2S> State in which displayed at scale of 1 x, and only

waveforms enlarged to 2 x.

< × 1>

1 ×

VECTOR SCALE 100%

Determines the scale of vector waveform.

<100%> Displays it at 100 % scale.

<75%> Displays it at 75 % scale.

75%

TIME CODE

OFF

Turns the time code display on and off.

MODE SELECT

LTC

Selects time code display mode.

VITC

LUB

VUB

<LTC>

Displays linear time code (LTC).

<VITC> Displays vertical interval time code (VITC).

<LUB> Displays user bits included in LTC.

<VUB> Displays user bits included in VITC.

CLOSED CAPTION

CC TYPE

OFF

Turns closed caption display on and off.

CEA-608

CEA-708

Selects the closed caption display mode.

<CEA-608> Displays data compliant with CEA-608.

<CEA-708> Displays data compliant with CEA-708.

CAPTION

CHANNEL

CC4

CC3

CC2

CC1

Selects the closed caption display channel for when CEA-608.

CAPTION

SERVICE

SRV6

SRV5

SRV4

SRV3

SRV2

SRV1

Selects the closed caption display service for when CEA-708.

Opens the vector display during SDI signal input.

Available during VIDEO input. Closed captions appear as bright lines on line 21 when closed caption is

set to ON and underscan is also on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Menu (continued)

CONTROL

The underlined values are factory preset setting values.

Description

Selects operation. (with control clock)

Sub menu

Settings

CONTROL

LOCAL

REMOTE

<LOCAL>

Enables front panel operation

<REMOTE> Enables remote operation (front panel

operation is locked)

LOCAL ENABLE

DISABLE

INPUT

Selects the disabled operation on the front panel when

selecting “REMOTE” under “CONTROL”.

<DISABLE> Disables all front panel operations.

<INPUT>

All controls except [INPUT SELECT] and the

volume knob are disabled.

The menu can be displayed when the lock is engaged.

Only “CONTROL/LOCAL ENABLE” menu items are available when the lock is engaged.

The picture adjusting knob is disabled when the lock is engaged.

The FUNCTION buttons cannot be operated when the lock is engaged.

The “LOCAL ENABLE” setting determines operations in lock mode.

The key mark is displayed during lock engagement.

[MAIN MENU]

Key mark

2D/3D ASSIST

Only available when “REMOTE” is selected under “CONTROL.”

HOURS METER

Sub menu

Settings

Description

OPERATION

XXXXXXh

Displays the number of hours it has been on.

Displays the number of hours that the backlight has been on.

LCD

“XXXXXX” indicates up to 262,800 hours (approx. 30 years). “OVER” is indicated when the number of

hours is 262,800 or higher.

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Assist Mode

The unit is equipped with 3D assist mode to provide support for shooting with a rig-type 3D camera system.

The 3D assist mode has the following functions.

■

Image input method: SIMULTANEOUS (simultaneous method)R

Two types of image, one for the left eye (L) and one for the right eye (R), are input to the two SDI1 and

SDI2 terminals.

• In 3D assist mode, the input is fixed to SDI1/SDI2 and the input line cannot be changed.

• An appropriate phase difference with the input signal of SDI2 is one that is up to ±15 µs using the input

signal of SDI1 as the reference.

• If the input signal formats of SDI1 and SDI2 are not identical or only one of the signals is input, the

screen display will black out.

■

Assist functions

Assist Function Name Screen Indication

Description

MIRROR

Side-by-side

Inverts the left and right and top and bottom of SDI2 (R) image

to enable the basic adjustments of a 3D camera to be made.

(Half-mirror type supported)

SHIFT

Overlay

Shifts SDI2 (R) image horizontally and vertically to enable the

lens axis of the 3D camera to be checked.

COMPARISON

CONVERGENCE

COLOR

Side-by-side

Displays a halftone marker on the inside. A subject captured

with only the camera of the L or R can be checked.

Normal 1

screen display

Switches the L/R images automatically or manually to enable

the convergence point to be checked.

Overlay

Overlays the L/R images on a checkerboard pattern to enable

the brightness or color offset to be checked.

ZOOM FOCUS

VERTICAL

OVERLAY

Side-by-side

Overlay

Enlarges part of an image to enable the focus offset or zoom

offset to be checked.

Displays the horizontal line markers to enable the vertical offset

to be checked.

Displays the vertical line markers to enable the width of parallax

to be checked.

■

How to switch to 3D assist mode

Select [3D ASSIST] in “2D/3D ASSIST” of the main menu.

The MIRROR assist functions starts, and a status screen

like the one shown in the figure on the rights appears.

3D ASSIST - MIRROR-

SDI1(L): 1080/60i(L) SDI2(R): 1080/60i(R)

Indicates the name of the assist function selected with

adjusting knob 4.

Indicates the format of the signal input to SDI1.

Indicates the format of the signal input to SDI2.

Indicates the functions assigned to adjusting knobs 1 to

4. For the functions assigned to adjusting knobs 1 to 3,

the definitions vary by assist function. The setting value

of each function is confirmed at the point in time when

the corresponding adjusting knob is operated. (pages

54 to 58)

MIRR

FUNC.

OFF

MIRROR

－

Adjusting knob 1 - 4

When you switch the mode to 3D assist mode, statuses 1 to 3 are displayed.

When you operate the function of 4 : If you press one of the adjusting knobs 1 to 4, statuses 1 to 3

disappear and status 4 is displayed. Status 4 continues to be displayed until the operation ends.

When you end the operation of 4 : If you press the FUNCTION3 button, status 4 disappears and statuses

1 to 3 are displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Assist Mode (continued)

<Note>

• When a signal on which the LR information is superimposed is input to SDI1 such as when there is an

AG-3DA1 connection, that LR information is displayed on the right side of the signal format. If L and R are

incorrectly input, the LR information is displayed in yellow. If the LR information is input to SDI2 only, the

LR information is not displayed on the right side of the signal format.

■

How to switch the assist function

Turn adjusting knob 4 (rightmost knob). Each turn clockwise switches the assist function in the order

shown in the table above.

<Notes>

• When you switch to 3D assist mode, dedicated functions are assigned to the picture adjusting knobs and

FUNCTION3 button in the control section on the front panel.

• When you want to make picture adjustments, switch to 2D mode.

• To make picture adjustments while still in 3D assist mode, press the FUNCTION3 button to turn ON the 2D

picture quality adjustment mode, and then switch the function of the adjusting knob to the 3D assist mode

function.

(If you turn OFF the 2D picture quality adjustment mode (2D ADJUST), the adjusting knob is reset to the

3D assist mode function.)

• The setting value is saved and the mode is returned to 3D assist mode when you press [ENTER] or when

10 seconds elapses after the setting value is changed.

■

How to return to 2D mode

Select [2D] in "2D/3D ASSIST” of the main menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Assist Mode (continued)

MIRROR (Left/Right and Top/Bottom inversion)

This function inverts just the left and right or top and bottom or both the left and right and top and bottom of

the input signals of SDI2 (R) to enable the basic adjustments of a rig-type 3D camera system (half mirror

type) to be made.

Screen:

The L/R 2 screens are shown side-by-side.

<Notes>

• Left and right inversion and top and bottom

inversion are also reflected in other assist

functions.

• The inversion setting information is even saved

when the power is turned off.

MIRR

MIRROR

－

FUNC.

The underlined values are factory preset setting values.

Sub menu Operation

Settings Description

MIRROR

Knob1 (turn) OFF

Inverts the left and right and the top and bottom of the input

signals on the SDI2 (R) side.

LRTB

<OFF> Do not invert

<TB> Invert Top and Bottom

<LRTB> Invert Both Left and Right/Top and Bottom

<LR> Invert Left and Right

SHIFT (Horizontal and Vertical Shift)

This function shifts the images of SDI2 (R) horizontally or vertically to enable you to overlay the images.

You can check the lens axis of a rig-type camera system while checking the rotation offset of the image.

Screen:

L/R are overlaid in one screen.

<Note>

The setting information for shifting images with

the SHIFT function is not memorized. The initial

display state is restored when you switch to the

COMPARISON function or another assist function.

SHFT

FUNC.

－

The underlined values are factory preset setting values.

Description

Sub menu Operation

Settings

Knob1 (turn)

Knob2 (turn)

-128 - 0 - 127

-32 - 0 - 31

Shifts the images on the SDI2 (R) side horizontally.

Shifts the images on the SDI2 (R) side vertically.

COMPARISON (Composition Check)

This function is for checking when the subject is captured with only the camera of one side.

Screen:

The L/R 2 screens are shown side-by-side, and a

70% size half-tone marker is shown inside each of

the images.

If there is an image shown on either only the left or

right, discomfort will be felt and stereoscopic vision

will become difficult when the mode is set to 3D.

Perform a comparison check of the parts of the

images outside of the markers.

CMPR

FUNC.

－

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Assist Mode (continued)

CONVERGENCE (Convergence Check)

This function is for checking the subject’s position at a fixed screen position in order to determine the depth

position of the main subject.

Automatically or manually switch the SDI1 (L) image and SDI2 (R) image and then check the subject’s position.

Screen:

Normal display of one screen

• The place at which the image does not change is

the convergence point.

• If the camera adjustment (vertical or rotation

direction position adjustment) is correct, the image

at other than the convergence point will shift to

MANU

SLOW CONV

the left/right target.

MODE MANUAL SPEED FUNC.

The underlined values are factory preset setting values.

Sub menu Operation

Settings

Description

MODE

Knob1 (turn)

Knob2 (turn)

Knob3 (turn)

MANU

AUTO

Selects the switching method of the L side image and R

side image.

<MANU> Manual switching <AUTO> Automatic switching

MANUAL

SPEED

Selects the image to display when the MODE menu is

MANU.

<L> Image of L side

<R> Image of R side

SLOW

FAST

Selects the speed for when the MODE menu is auto

switching.

<SLOW> Every 1 second

<FAST> Every 4 frames (When 720P: Every 8 frames)

COLOR (Color Check)

This function overlays and displays the SDI1 (L) image and SDI2 (R) image on a checkerboard pattern in

one screen to enable you to check the brightness offset and color differences

Screen:

Overlay L/R on one screen.

If it is easy to see the borderline of the checkerboard

pattern, the brightness or color of L/R images is

offset.

128

SIZE

COLR

FUNC.

－

The underlined values are factory preset setting values.

Description

Sub menu Operation

SIZE Knob1 (turn)

Settings

128

256

Selects the checkerboard grid size for when overlaying the

image of the L side and image of the R side.

<128> The checkerboard grid consists of squares of 128

samples and 128 lines.

<256> The checkerboard grid consists of squares of 256

samples and 256 lines.

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Assist Mode (continued)

ZOOM FOCUS (Zoom and Focus Check)

This function enlarges part of an image to enable you to check the focus offset and zoom offset on the left

and right, which tends to cause eye fatigue.

Screen:

The L/R 2 screens are shown side-by-side.

Expanding the parts that are not in focus makes

it easy to check the focus of the left and right

cameras.

OFF

ZOOM F-IN-R

OFF

ZOOM

FUNC.

－

The underlined values are factory preset setting values.

Description

Sub menu Operation Settings

ZOOM

Knob1

(turn)

Selects the signal display position of the enlarged

image (PIXEL TO PIXEL).

<Notes>

• If you press F-IN-R (operation knob 2) and then set

the FOCUS-IN-RED function to ON, the ZOOM menu

is disabled and the FOCUS-IN-RED function is given

priority.

• If the FOCUS-IN-RED function is then set to OFF,

the ZOOM menu is restored to the setting before the

FOCUS-IN-RED was set to ON.

(When 1080 signal input)

OFF

<OFF> Displays two screens side-by-side

<C>

Center of screen

Top left of screen

<LT>

<CT> Top center of screen

<RT> Top right of screen

<RB> Bottom right of screen

<CB> Bottom center of screen

<LB> Bottom left of screen

(When 720P signal input)

OFF

<OFF> Displays two screens side-by-side

<C>

<L>

<R>

Center of screen

Left of screen

Right of screen

F-IN-R

Knob2

(press)

OFF

0 - 30L

0 - 30R

Turns OFF/ON the FOCUS-IN-RED function in the

displayed screen.

<OFF>

Turns OFF the function.

<0 to 30L> Displays the SDL1 (L) image side in

1-screen display and turns ON the function.

<0 to 30R> Displays the SDL2 (R) image side in

1-screen display and turns ON the function.

(The numerical value is the detection sensitivity level

and is common to the left and right.)

Knob3

(turn)

0 - 30L

0 - 30R

Adjusts the detection sensitivity of FOCUS-IN-RED.

(The numerical value turns green when sensitivity

adjustment can be made.)

A higher numerical value results in lower detection

sensitivity (lack of sharpness).

<0 to 30> The detection level, which is common to the

left and right.

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Assist Mode (continued)

VERTICAL (Vertical Offset Check)

This function enables you to operate two horizontal line markers to check the number of lines between

markers in the displayed image and check vertical offset, which tends to cause eye fatigue.

Screen:

The L/R 2 screens are shown side-by-side, and two

markers are shown.

• Displaying horizontal line markers makes it easy

to check the left/right vertical offset.

• If the vertical offset becomes large, discomfort will

be felt and stereoscopic vision will become difficult

when the mode is set to 3D so make adjustments

trying your hardest to eliminate camera vertical

offset.

DISP

384

VTCL

EXPAND MARKER1 MARKER2 FUNC.

13 Lines

• The number of lines of the displayed image is

measured and then the number of lines between

the two horizontal line markers is displayed at the

bottom left of the screen.

The underlined values are factory preset setting values.

Description

Sub menu

Operation

Settings

EXPAND

Knob1 (press)

DISP

×1

Selects the display screen.

<DISP>

Displays the full screen.

×2

<×1> (x1) Displays the screen with the actual number

of pixels (PIXEL TO PIXEL)

<×2> (x2) Expands the actual number of pixels to

x2 in the vertical direction only and then

displays the screen.

Knob1 (turn)

Selects the display position for when the EXPAND

setting is x1 or x2.

<T> Displays the top of the input image.

<C> Displays the center of the input image.

<B> Displays the bottom of the input image.

MARKER1

MARKER2

Knob2 (turn)

Knob3 (turn)

0 - 384 - 767

Shifts the upper horizontal line marker up or down.

Shifts the lower horizontal line marker up or down.

When the signal format is 720P, the display position of the image is not shifted when x1 display.

The two horizontal line markers are each indicated by two lines, and the position of the upper line is

indicated.

Download from Www.Somanuals.com. All Manuals Search And Download.

3D Assist Mode (continued)

OVERLAY (Parallax Check)

This function displays vertical line markers to enable you to check the width of parallax.

Overlay display

Screen:

L/R images are overlaid and shown on one screen,

and vertical line markers are shown at 3% intervals

across the horizontal image width.

• Vertical line markers can also be displayed in

a gray screen in which the parallax portion is

emphasized (gray display).

STD

OVERLAY

MARKER

OVLY

FUNC.

－

If the parallax is way too large, stereoscopic vision

will become difficult when 3D images are viewed so

check the width of parallax of the L side and R side

images, using the width of the vertical line markers

as a reference.

Gray display

GRAY

OVERLAY

MARKER

OVLY

FUNC.

－

The underlined values are factory preset setting values.

Sub menu

Operation

Settings

Description

OVERLAY

Knob1 (turn)

STD

GRAY

Selects overlay or gray display (displays image

differences that emphasize the parallax portion).

<STD> Overlay display

<GRAY> Gray display (differences display)

MARKER

Knob2 (turn)

0 - 19 - 38

Shifts the vertical line marker in the horizontal

direction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Item Restrictions

■

List of Setting Item Restrictions in 2D Mode

(: Can be set and the function is enabled)

YP_BP_R

SDI1/SDI2

HDMI

YP_BP_R

Input CH

VIDEO

640

480

VIDEO

SD HD

SD HD SD HD

Settings

2D/3D ASSIST



MARKER

* *

16:9

4:3

* *

BACK

* *

CENTER

* *

MARKER

GPI MARKER1

GPI MARKER2

MARKER TYPE

CROSS HATCH

SIZE

* *



GAMMA SELECT

FILM GAMMA

COLOR TEMP.

SHARPNESS MODE

SHARPNESS H

SHARPNESS V

I-P MODE



VIDEO

CONFIG

MONO

ANAMO

* *

SD ASPECT



* *

SCAN



* *

SUB WINDOW

MENU POSITION

STATUS DISPLAY

BATTERY REMAIN



WARNING VOLTAGE

SETUP LOAD

SYSTEM

CONFIG

SETUP SAVE

POWER ON SETUP

COLOR SPACE

POWER SAVE MODE

CALIBRATION

AREA SETTING

VF CONTROL

REAR TALLY

CONFIG

ZEBRA

FUNCTION1

FUNCTION2

FUNCTION

FUNCTION3

FUNCTION DISPLAY

(Continued on next page)

This is not available when two screens are displayed with the SUB WINDOW function.

This is not available in PIXEL TO PIXEL mode.

Can be set but the function is disabled.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Item Restrictions (continued)

(: Can be set and the function is enabled)

YP_BP_R

SDI1/SDI2

HDMI

YP_BP_R

Input CH

VIDEO

640

480

VIDEO

SD HD

SD HD SD HD

Settings

GPI CONTROL

GPI1 - GPI8

VIDEO



GPI

FORMAT

NTSC SETUP

SDI1



SDI2

HDMI

INPUT

SELECT

YP_BP_R

COMPONENT LEVEL



VIDEO/ YP_BP_R

SIGNAL TYPE

INT SG



SELECT L

SELECT R

LEVEL METER

CH SELECT

POINT LINE

CH INFO.

HEAD ROOM

AUDIO



WFM/VECTOR

* *

POSITION



* *

VECTOR MODE

VECTOR SCALE

TIME CODE

* *

DISPLAY

SETUP

MODE SELECT

CLOSED CAPTION

CC TYPE



CAPTION CHANNEL

CAPTION SERVICE

CONTROL



CONTROL

LOCAL ENABLE

OPERATION

LCD

HOURS

METER

PEAKING

PHASE

CHROMA

IMAGE

ADJUSTMENT

BRIGHT

CONTRAST

BACKLIGHT

This is not available when two screens are displayed with the SUB WINDOW function.

This is not available in PIXEL TO PIXEL mode.

Can be set but the function is disabled.

VECTOR display is only shown when there is SDI input.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Item Restrictions (continued)

■

List of Setting Item Restrictions in 3D Assist Mode

(: Can be set and the function is enabled)

SDI1/SDI2

Input CH

Settings

2D/3D ASSIST

MARKER

Settings



GPI CONTROL

GPI1 - GPI8

VIDEO



GPI



16:9

4:3

FORMAT

NTSC SETUP

SDI1

BACK

CENTER

MARKER

GPI MARKER1

GPI MARKER2

MARKER TYPE

CROSS HATCH

SIZE

SDI2

HDMI

INPUT

SELECT

YP_BP_R

COMPONENT LEVEL

GAMMA SELECT

FILM GAMMA

COLOR TEMP.

SHARPNESS MODE

SHARPNESS H

SHARPNESS V

I-P MODE



VIDEO/ YP_BP_R

SIGNAL TYPE

INT SG

SELECT L



SELECT R

VIDEO

CONFIG

LEVEL METER

CH SELECT

POINT LINE

CH INFO.

AUDIO

MONO



ANAMO

SD ASPECT

HEAD ROOM

WFM/VECTOR

SCAN

* *

SUB WINDOW

MENU POSITION

STATUS DISPLAY

BATTERY REMAIN

WARNING VOLTAGE

SETUP LOAD

SETUP SAVE

POWER ON SETUP

COLOR SPACE

POWER SAVE MODE

CALIBRATION

AREA SETTING

VF CONTROL

REAR TALLY

POSITION

* *



VECTOR MODE

VECTOR SCALE

TIME CODE

* *

DISPLAY

SETUP



MODE SELECT

SYSTEM

CONFIG

CLOSED CAPTION

CC TYPE

CAPTION CHANNEL

CAPTION SERVICE

CONTROL



CONTROL

LOCAL ENABLE

OPERATION

HOURS

METER

LCD

CONFIG

ZEBRA

FUNCTION1

FUNCTION2

FUNCTION

FUNCTION3

FUNCTION DISPLAY



Can be set but the function is disabled.

Some functions do not operate in 3D assist mode (page 40).

This is not available when two screens are displayed with the SUB WINDOW function.

This is not available in PIXEL TO PIXEL mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE Specifications

This monitor permits remote operation via GPI/SERIAL terminal.

GPI terminal

GPI screen items correspond to the following terminals. Use the GPI menu to assign functions to each

terminal (page 47).

Functions assigned to terminals are executed when GND (pin 5) is short-circuited (ON) or open (OFF).

■

Operating conditions

Level operation: Operates when GND is short-

circuited.

Edge operation: Operates when GND changes

from open to short-circuited.

<Notes>

• When level operation is assigned to more than

one terminal, the function operates as long as

one of the terminals is short-circuited.

• Hold the edge operation for at least 0.2

seconds after the change.

Pin number Signal

GPI1

GPI2

GPI3

GPI4

GND

GPI5

GPI6

GPI7

GPI8

GPI Terminal (9P)

Assigned item

Function

Operating conditions

—

UNDEF

Undefined (no function assigned)

MARKER1

ON/OFF

Switches marker display defined in “GPI

MARKER1” (page 27) in the “MARKER”

menu.

Level operation

(Short-circuited: ON, Open: OFF)

MARKER2

ON/OFF

Switches marker display defined in “GPI

MARKER2” (page 27) in the “MARKER”

menu.

Level operation

(Short-circuited: ON, Open: OFF)

MARKER BACK

HALF

Reduces the brightness of the background Level operation

outside the marker displayed in “GPI

MARKER1” (page 27) to 50 %.

(Short-circuited: ON, Open: OFF)

MARKER BACK

BLACK

Reduces the brightness of the background Level operation

outside the marker displayed in “GPI

MARKER1” (page 27) to 0 %.

(Short-circuited: ON, Open: OFF)

CENTER MARKER

Turns the center marker display on and

off. (When other markers are displayed,

this marker is superimposed on other

markers.)

Level operation

(Short-circuited: ON, Open: OFF)

SD ASPECT

SCAN

Sets the aspect ratio for SD signal input.

(Disabled during HD signal input)

Level operation (Short-circuited:

16:9, open: 4:3)

Switches the scan mode between

“UNDER” and “NORMAL”.

Level operation (Short-circuited:

UNDER, Open: NORMAL)

GAMMA SEL. FILM

Switches the gamma curve to FILM mode. Level operation (Short-circuited: FILM

mode, Open: STANDARD mode)

(Continued on next page)

When a 16:9 marker and a 4:3 marker are simultaneously selected and activated on a 16:9 aspect ratio

display, both markers are displayed.

When a 16:9 marker and a 4:3 marker are simultaneously displayed, the background of the marker

selected by the 16:9 marker is controlled.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE Specifications (continued)

Assigned item

Function

Operating conditions

GAMMA SEL. STDIO/ Switches the gamma curve to STDIO/PST Level operation (Short-circuited:

STDIO/ PST mode, Open:

STANDARD mode)

PST

mode.

INPUT SEL. VIDEO

INPUT SEL. SDI1

INPUT SEL. SDI2

INPUT SEL. HDMI

INPUT SEL. YP_BP_R

INPUT SEL. VF

INPUT SEL. INT SG

MONO

Switches the input line to VIDEO.

Switches the input line to SDI1.

Switches the input line to SDI2.

Switches the input line to HDMI.

Switches the input line to YP_BP_R.

Switches the input line to VF.

Edge operation

Switches the input line to INT SG.

Switches between color and monochrome Level operation (Short-circuited:

(MONO).

monochrome, Open: color)

R-TALLY

Lights the red tally.

Level operation

(Short-circuited: ON, Open: OFF)

G-TALLY

Lights the green tally.

Level operation

(Short-circuited: ON, Open: OFF)

PIXEL TO PIXEL

FOCUS-IN-RED

REMOTE

Switches screen display between input

size and display size.

Level operation

(Short-circuited: ON, Open: OFF)

Displays the outlines of the subject that

are in focus in red

Level operation

(Short-circuited: ON, Open: OFF)

Sets remote standby (turns off the

backlight, and turns off the power of

devices that are not required).

Level operation

(Short-circuited: ON, Open: OFF)

STANDBY

* *

When “R-TALLY” and “G-TALLY” simultaneously go on, the tally color changes to orange.

When remote standby is set to ON, the CONT. and B.LIGHT LEDs on the front flash.

If the GPI terminal to be assigned is set to a short-circuited state first and then MENU is operated to set

this item, the backlight turns off and the screen display disappears, so MENU operation becomes unable

to be checked. To change the setting of this item, be sure to set it when the GPI terminal is in the open

state.

Restrictions

• SD ASPECT does not operate when the input signal is HD.

• The MARKER items do not operate when the input line of the signal is VF.

• SD ASPECT, SCAN, WFM/VECTOR, MARKER, PIXEL TO PIXEL, and PIXEL POSITION do not operate

in SUB WINDOW mode.

• SCAN and MARKER do not operate in PIXEL TO PIXEL mode.

• GAMMA SELECT, SD ASPECT, SCAN, MARKER, and MONO do not operate when the input line of the

signal is HDMI and the signal format is 640 x 480.

■

Priority of assigned functions

• When both “MARKER1” and “MARKER2” are activated at the same time, “MARKER1” has priority.

However, when the display aspect ratio is 4:3, the “MARKER1” aspect ratio is 16:9 and the “MARKER2”

aspect ratio is 4:3, “MARKER2” is displayed. In this case, the “MARKER2” background is controlled.

• When “MARKER BACK HALF” and “MARKER BACK BLACK” are activated at the same time, “MARKER

BACK BLACK” has priority.

• INPUT SEL. are prioritized in the order of “INPUT SEL. VIDEO,” “INPUT SEL. SDI1,” “INPUT SEL.

SDI2,” “INPUT SEL. HDMI,” “INPUT SEL. YP_BP_R,” “INPUT SEL. VF,” and “INT SG.”

• When “GAMMA SEL. FILM” and “GAMMA SEL. STDIO/PST” are activated at the same time, “GAMMA

SEL. FILM” has priority.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE Specifications (continued)

SERIAL terminal

External operations can be performed via the RS-232C interface.

The following diagram and the table on the following SERIAL terminal pin arrangement and connections.

For details on systems using SERIAL, be sure to consult your dealer.

External Device Side

(Straight)

BT-LH910G Side

Pin number Signal

Pin number

Signal

N.C.

RXD

TXD

DTR

GND

DSR

RTS

CTS

N.C.

TXD

RXD

DSR

GND

DTR

CTS

RTS

N.C.

SERIAL terminals (9P)

■

Connectors and signals

Connector: D-SUB 9-pin (female)

Signal

Command format

STX (02h) Command

Data ETX (03h)

• The command is the 3-character string starting

with STX and ending with ETX.

• Append any data after the colon (:) following the

command, as required.

Pin number

Signal

N.C.

TXD

RXD

DSR

GND

DTR

CTS

RTS

N.C.

Description

Not connected

Transmission data

Reception data

Connected inside

Ground

■

Response formats

1. Setting command response

STX (02h) Command

ETX (03h)

Connected inside

Not connected

2. Query command response

STX (02h)

Data

3. Error response

STX (02h)

Error codes

■

Communication parameters

Error codes

ER001: Invalid command

ER002: Parameter error

Signal level

Synchro system

Transfer rate

Parity

RS-232C compliant

Asynchronous

9600 bps

None

Data length

Stop bit

8 bit

1 bit

Flow control

None

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE Specifications (continued)

■

Setting command

No Command

Description

Input switch

Data

Response

IIS

0: SDI1

5: VF

1: SDI2

8: HDMI

2: VIDEO

9: INT SG

3: YP_BP_R

IIS

VPC

Image quality

adjustment

CON00-60 : Contrast settings

BRI00-60 : Brightness settings

CRO00-60 : Chroma settings

PHA00-60 : Phase settings

VOL00-60 : Volume settings

VPC

OBO

OHV

Blue only

HV Delay

0: OFF

1: ON

OBO

OHV

1: H DELAY

2: V DELAY

2: HIGH

3: HV DELAY

VBL

Backlight

000-100: Backlight setting

VBL

DCH

DCW

DSD

DMK

Cross hatch

0: OFF

0: 40

1: LOW

1: 80

DCH

DCW

DSD

DMK

Cross hatch Size

Status display

Marker settings

0: CONTINUE

1: 3SEC OFF

2: OFF

16:9 marker

MK100: OFF

MK102: 88 %

MK104: 95 %

MK106: 13:9

MK108: 90 %

MK110: VISTA

MK101: 80 %

MK103: 93 %

MK105: 14:9

MK107: 4:3

MK109: CNSCO 2.35

MK111: 2: 1

MK112: CNSCO 2.39

MK1 080 - MK1 100: range of 80 % - 100 %

4:3 marker

MK200: OFF

MK202: 88 %

MK204: 95 %

MK201: 80 %

MK203: 93 %

MK208: 90 %

MK2 080 - MK2 100: range of 80 % - 100 %

Marker background

BAK0: NORMAL

BAK2: BLACK

BAK1: HALF

CMK1: ON

Center marker

CMK0: OFF

MGM

MCT

Gamma selection

1: STANDARD

2: FILM

3: STDIO/PST

MGM

MCT

Color temperature

settings

00: D56

03: VAR1

01: D65

04: VAR2

02: D93

05: VAR3

10-73: USER0 - 63

MBM

VPC

Black mode

0: OFF

1: ON

MBM

VPC

Sharpness settings

SHP0: LOW SHP1: HIGH

SHH00-30 Horizontal sharpness settings

SHV00-30 Vertical sharpness settings

(Continued on next page)

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE Specifications (continued)

No Command

Description

Data

1: MODE2

2: ON

Response

MIP

IP mode settings

0: MODE1

1: OFF

OMO

Monochrome

settings

OMO

MAS

MSC

MCO

MLE

SD aspect settings

Scan settings

0: 16:9

1: 4 :3

MAS

MSC

MCO

MLE

0: NORMAL

0: LOCAL

0: DISABLE

1: UNDER

1: REMOTE

1: INPUT

Control settings

Remote operation

settings

■

Query command

No Command

Description

Data

Response

1: SDI2

4: VIDEO

QIS

Input selection

0: SDI1

2: YP_BP_R

7: VF-YP_BP_R

11: HDMI

8: VF-VIDEO

12: INT SG

QPC

Image quality

adjustment

CON: Contrast setting value

BRI: Brightness setting value

CRO: Chroma setting value

PHA: Phase setting value

VOL: Volume setting value

00-60

QBO

QBL

Blue only

Backlight

0: OFF

000-100

0: OFF

0: 40

1: ON

QCH

QCW

Cross hatch

1: LOW

1: 80

2: HIGH

Cross hatch

Size

QMK

marker

MAK: Area marker

00: OFF

02: 88 %

04: 95 %

06: 13:9

08: 90 %

01: 80 %

03: 93 %

05: 14:9

07: 4:3

09: CNSCO 2.35

10: VISTA

11: 2: 1

12: CNSCO 2.39

80-100: USER80 - 100

BAK: Background

0: NORMAL 1: HALF

2: BLACK

CMK: Center marker

0: OFF

1: ON

QGM

Gamma

1: STANDARD

2: FILM

3: STDIO/PST

(Continued on next page)

When both 16:9 and 4:3 markers are displayed, the 16:9 marker state is returned.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE Specifications (continued)

No Command

Description

Color

Data

Response

QCT

00: D56

02: D93

04: VAR2

01: D65

03: VAR1

05: VAR3

temperature

10-73: USER0 - 63

QBM

QPC

Black Mode

Sharpness

0: OFF

0: LOW

00-30

1: ON

SHP : Sharpness mode

1: HIGH

SHH : Horizontal sharpness

value

SHV : Vertical sharpness

value

00-30

QIP

IP mode

Monochrome

SD Aspect

Scan

0: MODE1

1: OFF

1: MODE2

2: ON

QMO

QAS

QSC

QFR

0: 16:9

1: 4:3

0: NORMAL 1: UNDER

Format

01: 1080/60i

02: 1080/59.94i

03: 1080/50i, 1080/25PsF

04: 1080/30p

05: 1080/29.97p

06: 1080/25p

07: 1080/24p

08: 1080/23.98p

09: 1080/24PsF

10: 1080/23.98PsF

13: 720/60p

14: 720/59.94p

15: 576/50i

16: 480/59.94p

17: 480/59.94i

18: 576/50p

20: 1080/60p

21: 1080/59.94p

22: 1080/50p

23: 720/50p

51: 640×480 (60 Hz)

68: 640×480 (59.94 Hz)

00: NO SIGNAL

FF: UNSUPPORT SIGNAL

QID

Model

BT-LH910

Download from Www.Somanuals.com. All Manuals Search And Download.

VF (viewfinder) Specifications

11 12 13 14 15

16 17 18 19 20

VF Terminal (15P)

AJ-HPX3100G (Example)

This unit side VF Terminal

Camera side VF Terminal

Pin number

Signal

Description

Pin number Description

P_R

P_Rsignal

Y signal

P_Bsignal

Unused

GND

VF-P_R

VF-Y

P_B

VF-P_B

N.C.

GND

UNREG-GND

VF-P_R-GND

VF-Y-GND

VF-P_B-GND

ZEBRA-SW

UNREG-GND

P_R-GND

Y-GND

P_B-GND

GND of P_Rsignal

GND of Y signal

GND of P_Bsignal

ZEBRA-SW ON/OFF of zebra signal

GND

N.C.

GND

Unused

Serial data signal for serial-

parallel conversion

VF-DATA

Pulse signal for reading

serial data for serial-parallel

conversion

VF-WR

N.C.

Unused

VF-CLK Serial data clock pulse

signal

VF-CLK

UNREG-12V

A9.0V

PEAKING

SPARE

MARKER-SW

FRONT-VR

VR-GND

<Note>

The 1, 2, 3, 13, 14, 17, 18, and 19 pins of the VF connector on the camera side do not connect to the VF

connector on this unit side.

Download from Www.Somanuals.com. All Manuals Search And Download.

Error and Warning Displays

If for any reason an error occurs in this monitor, the LEDs above the picture adjusting knob flash at 1 second

intervals to inform of the error/warning.

Error and Warning displays

Symptom

Remedy

Warning of improper

operation status for the

camera settings

Check the setting values of the

camera.*²

is displayed.

Near end warning *¹

Battery level error *¹

The voltage display flashes.

Replace with a fully charged battery.

“END BATTERY” is displayed for Replace with a fully charged battery.

approximately 3 seconds before

the power supply switches OFF.

Set the BATTERY REMAIN menu item of the SYSTEM CONFIG menu to ON.

The condition to display differs depending on the type and settings of the camera used in combination

with the unit. For details, see the instruction manual of the camera.

Maintenance

• To clean the cabinet or surface of the liquid crystal protection panel, gently wipe with a soft, dry cloth.

If the surfaces are extremely dirty, use a soft cloth dipped in a weak detergent solution and then wrung-out

to clean the surfaces, then use a dry cloth to finish. Water or similar substances getting inside the monitor

can cause a malfunction.

• Never use alcohol, thinner or benzene to clean this unit.

Doing so would cause the surface of the monitor to become discolored, and cause paint to peel.

• Do not spray cleansers directly onto the monitor.

Water or similar substances getting inside the monitor can cause a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

■

General

Input power: DC12 V (11.0 V - 17.0 V)

Input current:1.9A (DC12 V)

is the safety information.

Dimensions (W × H × D):

230 mm × 214.5 mm × 170 mm (including stand)

[9-1/16 inches × 8-7/16 inches × 6-11/16 inches] (including stand)

230 mm × 183 mm × 78.5 mm (not including stand)

[9-1/16 inches × 7-3/16 inches × 3-7/8 inches] (not including stand)

Weight:

2.4 kg (5.29 lb) (including stand)

1.7 kg (3.75 lb) (not including stand)

0 °C to 40 °C (32 °F to 104 °F)

10 % to 85 % (no condensation)

–20 °C to 60 °C (–4 °F to 140 °F)

Operating temperature:

Operating humidity:

Storage temperature:

■

Panel

Size:

23 cm (9.0 inch) (Effective display area)

15:9

1280 × 768 (WXGA)

Aspect ratio:

Number of pixels:

Display colors:

Approx. 16,770,000 colors

View angle (contrast > 10:1): 176 ° up/down, 176 ° right/left

■

Input/output Connectors

VIDEO input:

Analog component (YP_BP_R) input: 1 line, BNC × 3

(Of these, the Y input terminal is shared with the VIDEO input terminal)

1 line, BNC × 1 (Shared with the analog component Y input terminal)

HDMI input:

1 line, HDMI × 1 (Type A) (HDCP supported)

EMBEDDED AUDIO supported

VIERA Link not supported

SDI input:

2 line, BNC × 2

SMPTE274M/296M/259M-C/ITU-R BT.656-4 compliant

EMBEDDED AUDIO HD-SDI: SMPTE299M compliant

SD-SDI: SMPTE272M compliant

2 line, BNC × 2

SDI output (active through):

VF:

D-SUB, 15 pins × 1

GPI:

D-SUB, 9 pins × 1

SERIAL:

D-SUB, 9 pins × 1

Headphone output:

Stereo mini jack M3 × 1 32 Ω, level adjustable

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (continued)

■

List of Signal Formats Supported in 2D Mode

(: Compatible)

Input Signal Format/

Status displays

VIDEO VF-VIDEO VF-YP_BP_R

YP_BP_R

SDI1

SDI2

HDMI

NTSC



PAL

640×480 (59.94Hz)

640×480 (60Hz)

480/59.94i

480/59.94p

576/50i



576/50p



720/50p



720/59.94p

720/60p

1035/59.94i

1035/60i

1080/23.98PsF

1080/24PsF

1080/25PsF

1080/50i



1080/59.94i

1080/60i

1080/23.98p

1080/24p

1080/25p

1080/29.97p

1080/30p

1080/50p

1080/59.94p

1080/60p

When 1035/59.94I signal is input, displayed as 1080/59.94I. Other various marker displays will use the

1080/59.94I marker.

When 1035/60I signal is input, displayed as 1080/60I. Other various marker displays will use the

1080/60I marker.

When 1080/25PsF signal is input, displayed as 1080/50i. Other various marker displays will use the

1080/50i marker.

RGB444 and SDI422 (12 bit) are not supported.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (continued)

■

List of Signal Formats Supported in 3D Assist Mode

(: Compatible)

Input Signal Format/

Status displays

SDI1/2 (SIMUL)

720/50p



720/59.94p

720/60p

1035/59.94i

1035/60i

1080/23.98PsF

1080/24PsF

1080/25PsF

1080/50i

1080/59.94i

1080/60i

When 1035/59.94i signal is input, displayed as 1080/59.94i.

When 1035/60i signal is input, displayed as 1080/60i.

When 1080/25PsF signal is input, displayed as 1080/50i.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (continued)

■

Closed Caption Decoding

Supported Signals

Composite

SD-SDI

NTSC, PAL

480/59.94i, 576/50i

HD-SDI

1080/60i ¹, 720/60p ¹, 1080/50i, 720/50p,

1080/24PsF ¹, 1080/25PsF, 1080/30p

1080/24p ¹, 1080/25p

Supported Standards

Composite

SD-SDI

EIA/CEA-608 (VBI)

EIA/CEA-608 (ANC)

HD-SDI

EIA/CEA-608 (708) , EIA/CEA-708

Supported Specifications (EIA/CEA-608)

Decode channels

Character

CC1 - CC4

Standard Character, Special Charactor

Supported Specifications (EIA/CEA-708)

Caption service

Service #1 to #6

G0 Code, G1 Code, Window Style ³, Pen Style

Character

The frame frequency of 1/1.001 is also supported.

The XDS service is not supported.

Window Style

Only justify LEFT is supported.

Only print direction LEFT-TO-RIGHT is supported.

Only scroll direction BOTTOM-TO-TOP is supported.

Word wrap is not supported.

Only the display effect SNAP is supported.

Fill color is not supported.

Fill opacity is not supported.

Border type is not supported.

Pen Style

Pen size SMALL is supported.

Font style is 0

Only offset NORMAL is supported.

Italics is supported.

Underline is supported.

Only edge type UNIFORM is supported.

Foreground colors white, blue, green, yellow, cyan, red, gray, and magenta are supported.

Foreground opacity is not supported.

Background colors black and orange (orange is displayed when any color other than black is specified)

are supported.

Only background opacity black (semi-transparent) is supported.

Weight and dimensions are approximate.

Specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (continued)

■

INT SG (Internal chart for adjustment)

10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

GRAY

75%

YELLOW

75%

CYAN

75%

GREEN MAGENTA

RED

75%

BLUE

75%

-I

WHITE

BLACK

BLACK -4%

BLACK +4%

BLACK

Download from Www.Somanuals.com. All Manuals Search And Download.

Memo

Download from Www.Somanuals.com. All Manuals Search And Download.

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical

and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling, please take these products to designated

collection points, where they will be accepted on a free of charge basis. Alternatively, in

some countries you may be able to return your products to your local retailer upon the

purchase of an equivalent new product.

Disposing of this product correctly will help to save valuable resources and prevent any

potential negative effects on human health and the environment which could otherwise

arise from inappropriate waste handling. Please contact your local authority for further

details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with

national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct

method of disposal.

Ȭɩ ʀɀɻȸ̗Ꮱȸɳʀɟ

2011

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Dishwasher G4281 User Manual
MTD Chipper 243 645C000 User Manual
Multi Tech Systems Network Card ISIHP 2S User Manual
Napoleon Grills Outdoor Cart N415 0103 User Manual
National Instruments Network Card NI 9401 User Manual
Omega Engineering Computer Hardware OME A8111 User Manual
OPPO Digital DVD Player OPDV971H User Manual
Optoma Technology Projector GT750E User Manual
Oregon Scientific Watch RA126 User Manual
P3 International Home Security System P8315 User Manual