Onkyo Stereo System HT RC270 User Manual

Contents

AV Receiver

Introduction ...................................2

Connections.................................13

Turning On & Basic Operations ......24

Advanced Operations .................41

HT-RC270

Instruction Manual

Controlling iPod & Other

Components............................71

Others...........................................82

Thank you for purchasing an Onkyo AV Receiver.

Please read this manual thoroughly before making

connections and plugging in the unit.

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new AV Receiver.

Please retain this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal without

the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-ser-

viceable. If you cannot turn on the unit, contact your

Onkyo dealer.

3. Care—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners, alco-

hol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

4. Power

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved

by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV techni-

cian for help.

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the volt-

age requirements printed on the unit’s rear panel (e.g.,

AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug is

readily operable (easily accessible) at all times.

Pressing ON/STANDBY to select Standby mode does

not fully shutdown the unit. If you do not intend to use

the unit for an extended period, remove the power cord

from the AC outlet.

5. Preventing Hearing Loss

Caution

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS COM-

PLIES WITH CANADIAN ICES-003.

Excessive sound pressure from earphones and head-

phones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

For models having a power cord with a polarized plug:

Batteries (battery pack or batteries installed) shall not

be exposed to excessive heat as sunshine, fire or the

like.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

7. Never Touch this Unit with Wet Hands—Never han-

dle this unit or its power cord while your hands are

wet or damp. If water or any other liquid gets inside

this unit, have it checked by your Onkyo dealer.

8. Handling Notes

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB-

003 DU CANADA.

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally

bought it.

• Do not leave rubber or plastic items on this unit for

a long time, because they may leave marks on the

case.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPON-

DANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be

sure to use it occasionally.

Download from Www.Somanuals.com. All Manuals Search And Download.

Supplied Accessories

Make sure you have the following accessories:

Indoor FM antenna (➔ 21)

AM loop antenna (➔ 21)

Speaker cable labels (➔ 13)

Speaker setup microphone (➔ 29)

Remote controller and two batteries (AA/R6)

In catalogs and on packaging, the letter at the end of the prod-

uct name indicates the color. Specifications and operations are

the same regardless of color.

Using the Remote Controller

Installing the Batteries

Note

• If the remote controller

doesn’t workreliably, try

replacing the batteries.

• Don’t mix new and old

batteries or different

types of batteries.

• If you intend not to use

the remote controller for

a long time, remove the

Batteries (AA/R6)

batteries to prevent dam-

age from leakage or corrosion.

• Remove expired batteries as soon as possible to prevent damage

from leakage or corrosion.

Aiming the Remote Controller

To use the remote controller, point it at the AV receiver’s

remote control sensor, as shown below.

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Introduction

Adva nced Operations

Important Safety Instructions ......................................... 2

Precautions....................................................................... 3

Supplied Accessories...................................................... 4

Using the Remote Controlle r .......................................... 4

Features ............................................................................ 6

Front & Rear Panel s ......................................................... 8

Front Panel..................................................................... 8

Display............................................................................ 9

Rear Panel ................................................................... 10

Remote Controller.......................................................... 11

Controlling the AV Receiver ......................................... 11

About Home Theate r ...................................................... 12

Enjoying Home Theater................................................ 12

Advance d Setup .............................................................4 1

On-screen Setup Menu s...............................................4 1

Common Pr ocedures in Setup Menu ...........................4 1

Input/Output Assig n ......................................................4 2

Speaker Setu p ..............................................................4 4

Audio Adjust .................................................................4 7

Source Setu p ................................................................4 8

Listening Mode Prese t ..................................................5 2

Miscellaneou s ...............................................................5 3

Hardware Setup............................................................5 3

Lock Setup....................................................................5 6

Using the Audio Settings ..............................................56

NET/USB..........................................................................5 9

About NE T ....................................................................5 9

Connecting the AV Receiver ........................................5 9

Listening to Internet Radio............................................6 0

Playing Music Files on a Server ...................................6 1

Remote Playback from Media Server/

Connections

Connecting the AV Receive r ......................................... 13

Connecting Your Speakers .......................................... 13

About AV Connections ................................................. 17

Connecting Your Components with HDMI.................... 18

Connecting Your Components ..................................... 19

Connecting Onkyo u Components ............................ 20

Connecting Antenna..................................................... 21

Which Connections Should I Use?............................... 22

Personal Compute r ....................................................6 4

Network Settings ..........................................................65

About US B ....................................................................6 6

Zone 2..............................................................................68

Connecting Zon e 2 .......................................................6 8

Setting the Power ed Zone 2 .........................................6 9

Using Zone 2 ................................................................6 9

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................... 24

Turning On ................................................................... 24

Turning Off ................................................................... 24

Basic Operations............................................................ 25

Selecting the Language Used for

Controlling iPod & Other Components

Controlling iPod .............................................................7 1

Connecting the iPod Directly to the USB Port ..............7 1

Connecting an Onkyo Doc k ..........................................7 2

Using the Onkyo Doc k ..................................................7 3

Controlling Your iPod....................................................74

Controlling Other Components.....................................7 6

Preprogrammed Remote Control Code s ......................7 6

Looking up for Remote Control Cod e ...........................7 6

Entering Re mote Control Codes...................................7 7

Remote Control Codes for

Onkyo Components Connected via u .....................77

Resetting REMOTE MODE Button s.............................78

Resetting the Remote Controller ..................................78

Controlling Other Component s .....................................7 8

Learning C ommands ....................................................8 0

Using Normal Macro s ...................................................8 0

the Onscreen Setup Menu s ....................................... 25

Playing the Connected Component.............................. 25

Displaying Source Information ..................................... 25

Setting the Display Brightness ..................................... 25

Muting the AV Receiver................................................ 26

Using the Sleep Timer.................................................. 26

Selecting Speaker Layout ............................................ 26

Using the Home Menu.................................................. 26

Changing the Input Display .......................................... 27

Using Headphones....................................................... 27

Using Easy Macros ...................................................... 28

Audyssey MultEQ^®Room Correction and

Speaker Setu p ........................................................... 29

Listening to the Radio ................................................... 32

Using the Tuner............................................................ 32

Presetting FM/AM Stations........................................... 33

Recording ....................................................................... 34

Using the Listening Modes ........................................... 35

Selecting Listening Modes ........................................... 35

About Listening Modes................................................. 36

Others

Troubleshooting.............................................................82

Specifications.................................................................87

About HDMI.....................................................................88

Using an RIHD-compatible TV, Player, or Recorder ...89

Video Resolution Chart..................................................91

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press

ON/STANDBY (➔ 82).

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

Amplifier

Miscellaneous

• 100 Watts/Channel @ 8 ohms (FTC)

• WRAT–Wide Range Amplifier Technology

(5 Hz to 100 kHz bandwidth)

• 40 FM/AM Presets

®*4

• Audyssey MultEQ

lems

to Correct Room Acoustic Prob-

®*4

• Linear Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

• Audyssey Dynamic EQ

for Loudness Correction

®*4

• Audyssey Dynamic Volume

Listening Level and Dynamic Range

to Maintain Optimal

• Crossover Adjustment

Processing

(40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 250 ms)

• Auto Power-down Function

• THX Select2 Plus Certified

• HDMI Video Upscaling (to 1080p Compatible) with

Faroudja DCDi Cinema Enhancement

• On-Screen Display via HDMI

• Preprogrammed (with onscreen display setup) RI-Com-

patible Learning Remote with 4 Activities and Mode-

Key LEDs

• HDMI (Ver.1.4a with Audio Return Channel, 3D), Deep-

Color, x.v.Color , Lip Sync, DTS -HD Master Audio,

DTS-HD High Resolution Audio, Dolby TrueHD ,

Dolby Digital Plus, DSD and Multi-CH PCM

• Dolby Pro Logic IIz – New Surround Format (front-

high)

• Audyssey DSX™ for New Surround Channels (front-

wide/front-high)

Manufactured under license from THX Ltd. U.S. and foreign

patent applications pending. THX and the THX logo are

trademarks of THX Ltd. which are registered in some jurisdic-

• 4 DSP Modes for Gaming; Rock/Sports/Action/RPG

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• Direct Mode

Manufactured under license under U.S. Patent #'s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;

7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and

worldwide patents issued & pending. DTS and the Symbol are

registered trademarks, & DTS-HD, DTS-HD Master Audio,

and the DTS logos are trademarks of DTS, Inc. Product

includes software.

• Pure Audio Mode

• Music Optimizer for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

• Jitter Cleaning Circuit Technology

Connections

• 6 HDMI Inputs (1 on front panel) and 1 Output

• Onkyo p for System Control

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, “Surround EX” and the double-D sym-

bol are trademarks of Dolby Laboratories.

• 5 Digital Inputs (2 Optical/3 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• Universal Port for the Optional Dock for iPod /HD

Radio™ tuner module

• Dual Subwoofer Pre Out

• Banana Plug-Compatible Speaker Posts

• Powered Zone 2

Manufactured under license from Audyssey Laboratories™.

U.S. and foreign patents pending. Audyssey MultEQ^®,

Audyssey DSX™, Audyssey Dynamic Volume^®and

Audyssey Dynamic EQ^®are registered trademarks and trade-

marks of Audyssey Laboratories.

• Internet Radio Connectivity (SIRIUS Internet Radio /

vTuner/Pandora/Rhapsody/Slacker/Mediafly/Napster)

Services available may vary depending on the region.

Music Optimizer™ is a trademark of Onkyo Corporation.

• Network Capability for Streaming Audio Files

• Bi-Amping Capability for FL/FR with SBL/SBR

• Analog RGB Video Input (D-sub 15) for PC

“HDMI, the HDMI Logo, and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.”

HD Radio™ and the HD Radio Ready logo are proprietary

trademarks of iBiquity Digital Corporation.

To receive HD Radio broadcasts, you must install an Onkyo

UP-HT1 HD Radio tuner module (sold separately).

Download from Www.Somanuals.com. All Manuals Search And Download.

SIRIUS, XM and all related marks and logos are trademarks

of Sirius XM Radio Inc. and its subsidiaries. All rights

reserved. Service not available in Alaska and Hawaii.

THX Select2 Plus

Before any home theater component can be THX Select2

Plus certified, it must pass a rigorous series of quality and

performance tests. Only then can a product feature the

THX Select2 Plus logo, which is your guarantee that the

Home Theater products you purchase will give you

superb performance for many years to come. THX

Select2 Plus requirements define hundreds of parameters,

including power amplifier performance, and pre-ampli-

fier performance and operation for both digital and ana-

log domains. THX Select2 Plus receivers also feature

proprietary THX technologies (e.g., THX Mode) which

accurately translate movie soundtracks for home theater

playback.

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod

touch are trademarks of Apple Inc., registered in the U.S. and

other countries. iPad is a trademark of Apple Inc.

“Made for iPod” and “Made for iPhone” mean that an elec-

tronic accessory has been designed to connect specifically to

iPod or iPhone, respectively, and has been certified by the

developer to meet Apple performance standards. Apple is not

responsible for the operation of this device or its compliance

with safety and regulatory standards.

“x.v.Color” is a trademark of Sony Corporation.

Rhapsody and the Rhapsody logo are registered trademarks of

RealNetworks, Inc.

“DLNA^®, the DLNA Logo and DLNA CERTIFIED™ are

trademarks, service marks, or certification marks of the Digi-

tal Living Network Alliance.”

Download from Www.Somanuals.com. All Manuals Search And Download.

Front & Rear Panels

Front Panel

b cdefg

i j k l

m n o

u v w x y

r s

The actual front panel has various logos printed on it. They are not shown here for clarity.

The page numbers in parentheses show where you can find the main explanation for each item.

a ON/STANDBY button (➔ 24)

b STANDBY indicator (➔ 24)

c HDMI THRU indicator (➔ 55)

d ZONE 2 indicator (➔ 69)

e Remote control sensor (➔ 4)

n TUNING, PRESET (➔ 32 to 33), arrow and

ENTER buttons

o RETURN button

p MASTER VOLUME control and indicator (➔ 25)

q PHONES jack (➔ 27)

r AUX INPUT HDMI jack (➔ 18)

s PURE AUDIO button and indicator (➔ 35)

f ZONE 2, OFF, ZONE 2 LEVEL/TONE LEVEL

and TONE buttons (➔ 56, 69 to 70)

g Display (➔ 9)

t Input selector buttons (BD/DVD, VCR/DVR,

CBL/SAT, GAME, PC, AUX, TUNER , TV/CD,

PHONO, PORT and NET/USB) (➔ 25 )

h LISTENING MODE buttons (MOVIE/TV, MUSIC

and GAME) (➔ 35)

u USB port (➔ 66)

i DIMMER button (➔ 25)

j MEMORY button (➔ 33)

k TUNING MODE button (➔ 32)

l DISPLAY button (➔ 25)

m SETUP button (➔ 41)

v AUX INPUT LINE IN jack (➔ 19)

w AUX INPUT VIDEO jack (➔ 19)

x AUX INPUT AUDIO jacks (➔ 19)

y SETUP MIC jack (➔ 29)

Download from Www.Somanuals.com. All Manuals Search And Download.

Display

h i

For detailed information, see the pages in parentheses.

a Speaker/channel indicators

b Z2 (Powered Zone 2) indicator (➔ 69)

c Listening mode and format indicators (➔ 35, 57)

d NETWORK indicator (➔ 60)

e Tuning indicators

g Bi AMP indicator (➔ 16)

h Headphone indicator (➔ 27)

i Audyssey indicator (➔ 29, 48 )

Dynamic EQ indicator (➔ 48 )

Dynamic Vol indicator (➔ 49)

j Message area

AUTO indicator (➔ 32)

TUNED indicator (➔ 32)

k USB indicator (➔ 66)

l Volume level (➔ 25)

FM STEREO indicator (➔ 32)

f SLEEP indicator (➔ 26)

m MUTING indicator (➔ 26)

n Audio input indicators

Download from Www.Somanuals.com. All Manuals Search And Download.

Rear Panel

a bcd

m n

* o p

a DIGITAL IN COAXIAL and OPTICAL jacks

b u REMOTE CONTROL jack

c UNIVERSAL PORT jack

l Composite, S-Video and analog audio jacks

(BD/DVD IN, VCR/DVR IN and OUT,

CBL/SAT IN, GAME IN, PC IN, TV/CD IN and

PHONO IN)

d ETHERNET port

m Multichannel input jacks

e MONITOR OUT V and S jacks

f HDMI IN and OUT jacks

(FRONT L/R, CENTER, SURR L/R,

SURR BACK L/R and SUBWOOFER)

g COMPONENT VIDEO IN and MONITOR OUT

n PRE OUT jacks

jacks

(FRONT L/R, CENTER, SURR L/R,

h FM ANTENNA jack and AM ANTENNA terminal

SB/FH/FW L/R and SUBWOOFER)

^*SB···Surround Back, FH···Front High, FW···Front Wide

i PC IN port

j Power cord

k GND screw

o ZONE 2 LINE OUT jacks

p Speaker Terminals

(FRONT L/R, CENTER , SURR L/R,

SURR BACK L/R, FRONT HIGH L/R and

FRONT WIDE/ZONE 2 L/R)

See “Connecting the AV Receiver” for connection infor-

mation (➔ 13 to 23).

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Controller

Controlling the AV Receiver

To control the A V r eceiver, press RECEIVER to select

Receiver mode.

You can also use the remote controller to control

Onkyo Blu-ray Disc/DVD player, CD player and

other components.

See “Entering Remote Control Codes” for more

details (➔ 77).

For detailed information, see the pages in par entheses.

a STANDBY button (➔ 24)

b ON button (➔ 24)

c ACTIVITIES buttons (ALL OFF, MY MOVIE, MY

TV and MY MUSIC) (➔ 28, 80)

d REMOTE MODE/INPUT SELECTOR buttons

(BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,

TUNER, TV/CD, PHONO, PORT and NET/USB)

(➔ 25)

e SP LAYOUT button (➔ 26)

f Arrow q/w/e/r and ENTER buttons

g SETUP button (➔ 41)

h LISTENING MODE buttons (MOVIE/TV, MUSIC,

GAME and THX) (➔ 35)

i DIMMER button (➔ 25)

j DISPLAY button (➔ 25)

k MUTING button (➔ 26)

l VOL q/w button (➔ 25)

m RETURN button

n HOME button (➔ 26)

o SLEEP button (➔ 26)

■ Controlling the tuner

To control the AV receiver’s tuner, press TUNER (or

RECEIVER).

You can select AM or FM by pressing TUNER repeatedly.

a Arrow q/w buttons (➔ 32)

b D.TUN button (TUNER remote mode only) (➔ 32)

c CH +/– button (➔ 33)

d Number buttons (➔ 32)

When you want to change the remote controller mode without

changing the current input source, press MODE and within

about 8 seconds, press REMOTE MODE. Then, with the AV

receiver’s remote controller, you can control the component

corresponding to the button you pressed.

VIDEO functions as a short cut of HOME.

Download from Www.Somanuals.com. All Manuals Search And Download.

About Home Theater

Enjoying Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your

own home—just like being in a movie theater or concert hall. With Blu-ray Discs or DVDs, you can enjoy DTS and

Dolby Digital. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP lis-

tening modes.

You can also enjoy THX Surround EX (THX-certified THX speaker system recommended).

a b Front speakers (Left and Right)

These output the overall sound. Their role in a home theater is to pro-

vide a solid anchor for the sound image. They should be positioned

facing the listener at about ear level, and equidistant from the TV.

Angle them inward so as to create a triangle, with the listener at the

apex.

Center speaker

This speaker enhances the front speakers, making sound movements

distinct and providing a full sound image. In movies it’s used mainly

for dialog. Position it close to your TV facing forward at about ear

level, or at the same height as the front speakers.

d e Surround speakers (Left and Right)

These speakers are used for precise sound positioning and to add real-

istic ambience. Position them at the sides of the listener, or slightly

behind, about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they

should be equidistant from the listener.

Subwoofer(s)

The subwoofer handles the bass sounds of the LFE (Low-Frequency

Effects) channel. The volume and quality of the bass output from your

subwoofer will depend on its position, the shape of your listening

room, and your listening position. In general, a good bass sound can be

obtained by installing the subwoofer in a front corner, or at one-third

the width of the wall, as shown.

de gh

g h Surround back speakers (Left and Right)

These speakers are necessary to enjoy Dolby Digital EX, DTS-ES

Matrix, DTS-ES Discrete, THX Surround EX, etc. They enhance the

realism of surround sound and improve sound localization behind the

listener. Position them behind the listener about 2 to 3 feet (60 to

100 cm) above ear level.

Corner

position

i j Front high speakers (Left and Right)

These speakers are necessary to enjoy Dolby Pro Logic IIz Height, and

Audyssey DSX™. They significantly enhance the spatial experience.

Position them at least 3.3 feet (100 cm) above the front speakers (pref-

erably as high as possible) and at an angle slightly wider than the front

speakers.

1/3 of wall

position

Tip

• To find the best position for your subwoofer, while

playing a movie or some music with good bass,

experiment by placing your subwoofer at various

positions within the room, and choose the one that

provides the most satisfying results.

k l Front wide speakers (Left and Right)

These speakers are necessary to enjoy Audyssey DSX. They signifi-

cantly enhance the spatial experience. Position them well outside of the

front speakers. See also http://www.audyssey.com/technology/dsx.html

about optimum speaker placement for Audyssey DSX.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting the AV Receiver

Speaker Connection Precautions

Connecting Your Speakers

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between

4 and 16 ohms. If the impedance of any of the connected

speakers is 4 ohms or more, but less than 6 ohms, be sure

to set the minimum speaker impedance to “4ohms”

(➔ 44). If you use speakers with a lower impedance, and

use the amplifier at high volume levels for a long period

of time, the built-in protection circuit may be activated.

• Disconnect the power cord from the wall outlet before

making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+)

terminals, and negative (–) terminals only to negative (–)

terminals. If you get them the wrong way around, the

sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may

affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver.

Speaker Configuration

The following table indicates the channels you should use

depending on the number of speakers that you have.

For 7.1-channel surround-sound playback, you need 7

speakers and a powered subwoofer.

Number of 2 3 4 5 6 7 7 7 8 8 9 9 9 10 11

speakers

Front speakers ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

✔

Center

✔

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

speaker

Surround

speakers

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

✔

Surroundback

speaker

✔

✔ ✔

✔

*1*2

Surroundback

speakers

✔

✔ ✔

✔

Front high

✔

✔ ✔

speakers

Front wide

✔

✔ ✔ ✔

• Make sure the metal core of the wire does not have con-

tact with the AV receiver’s rear panel. Doing so may

damage the AV receiver.

speakers

If you’re using only one surround back speaker, connect it to

the SURR BACK L terminals.

Front high, surround back and front wide speakers cannot be

used at the same time.

No matter how many speakers you use, a powered sub-

woofer is recommended for a really powerful and solid

bass.

To get the best from your surround sound system, you

need to set the speaker settings. You can do this automati-

cally (➔ 29) or manually (➔ 44).

Attaching the Speaker Cable Labels

The AV receiver’s positive (+) speaker terminals are all

red (the negative (–) speaker terminals are all black).

• Don’t connect more than one cable to each speaker ter-

minal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Speaker

Color

Front left, Front high left, Front wide left,

Zone 2 left

White

Front right, Front high right, Front wide right,

Zone 2 right

Red

Center

Green

Blue

Surround left

Surround right

Surround back left

Surround back right

Gray

Brown

Tan

The supplied speaker cable labels are also color-coded and

you should attach them to the positive (+) side of each

speaker cable in accordance with the table above. Then all

you need to do is to match the color of each label to the

corresponding speaker terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Speaker Cables

Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of

insulation from the ends of the

speaker cables, and twist the bare

wires tightly, as shown.

1/2" to 5/8"(12 to 15 mm)

Using Banana Plugs

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one

surround back speaker, connect it to the SURR BACK L terminals.

Front high

right　

speaker

Front wide

right

speaker

Front wide

left

speaker

Front high

left

speaker

Front right

speaker

Front left

speaker

Center

speaker

Surround

right

speaker

Surround

back right

speaker

Surround

back left

speaker

Surround

left

speaker

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Dipole Speakers

Normal speakers

Dipole speakers

You can use dipole speakers for the surround and surround

back speakers. Dipole speakers output the same sound in two

directions.

Dipole speakers typically have an arrow printed on them to

indicate how they should be positioned. The surround dipole

speakers should be positioned so that their arrows point

toward the TV/screen, while the surround back dipole speak-

ers should be positioned so that their arrows point toward

each other, as shown.

TV/screen

ab Front speakers

Center speaker

de Surround speakers

Subwoofer(s)

gh Surround back speakers

ij Front high speakers

kl Front wide speakers

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s

SUBWOOFER PRE OUT jack to an input on

your powered subwoofer, as shown. If your sub-

woofer is unpowered and you’re using an external

amplifier, connect the SUBWOOFER PRE OUT

jack to an input on the amp.

Powered subwoofer

LINE INPUT

You can connect the powered subwoofer with two

SUBWOOFER PRE OUT jacks respectively.

The same signal is output from each jack.

LINE INPUT

Download from Www.Somanuals.com. All Manuals Search And Download.

Bi-amping the Front Speakers

The FRONT L/R and SURR BACK L/R terminal posts can be

used with front speakers and surround back speakers respec-

tively, or bi-amped to provide separate tweeter and woofer feeds

for a pair of front speakers that support bi-amping, providing

improved bass and treble performance.

• When bi-amping is used, the AV receiver is able to drive up to

a 5.1 speaker system in the main room.

• For bi-amping, the FRONT L/R terminal posts connect to the

front speakers’ woofer terminals; the SURR BACK L/R ter-

minal posts connect to the front speakers’ tweeter terminals.

• Once you’ve completed the bi-amping connections shown

below and turned on the AV receiver, you must set the

“Speakers Type(Front)” setting to “Bi-Amp” to enable bi-

amping (➔ 44).

Left

speaker

Right

speaker

Tweeter (high)

Woofer (low)

Important:

• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low)

terminals.

• Bi-amping can be used only with speakers that support bi-amping. Refer to your speaker manual.

Connecting a Power Amplifier

If you want to use a more powerful power amplifier and use the AV receiver as a preamp, connect it to the PRE OUT

jacks, and connect all speakers to the power amplifier.

PRE OUT

SB/FH/FW

FRONT

CENTER

SURR

Power amplifier

FRONT

CENTER

SURR

SURR BACK OR

FRONT HIGH OR

FRONT WIDE

aFront left speaker

bCenter speaker

cFront right speaker

dSurround left speaker

eSurround right speaker

Note

Specify “None” for the channel that you don’t want to output

(➔ 44).

SB···Surround Back, FH···Front High, FW···Front Wide

fSurround back/Front wide/Front high left speaker^*1

gSurround back/Front wide/Front high right speaker^*1

Download from Www.Somanuals.com. All Manuals Search And Download.

About AV Connections

Connected image with AV components

: Audio

HDMI cable

Other cables

: Video

AV receiver

: Video & Audio

AV receiver

Blu-ray Disc/

DVD player

Blu-ray Disc/

DVD player

Game console

Right!

TV, projector, etc.

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunc-

tions).

Wrong!

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

AV Cables and Jacks

Signal

Cable

Jack

Description

Video and

Audio

HDMI

HDMI connections can carry digital video and audio.

HDMI

Video

Component video

Component video separates the luminance (Y) and color

difference signals (PB/CB, PR/CR), providing the best pic-

ture quality (some TV manufacturers label their compo-

nent video sockets slightly differently).

Green

P^B/CB

PR/CR

Blue

Red

Analog RGB

This is a conventional analog interface to connect a PC and

a display device (also called D-Sub or D-subminiature).

S-Video

S-Video separates the luminance and color signals and pro-

vides better picture quality than composite video.

Composite video

Composite video is commonly used on TVs, VCRs, and

See also:

resolution

The input source is displayed with the default name even

• “Controlling Other Components” (➔ 76)

• “Controlling iPod” (➔ 71)

• “Listening to the Radio” (➔ 32)

when you have entered a custom name in “Name Edit”

(➔ 50).

If the input signal is analog, no format information is dis-

played. If the input signal is PCM, the sampling frequency is

displayed. If the input signal is digital but not PCM, the signal

format and the number of channels is displayed. For some dig-

ital input signals, including multichannel PCM, the signal for-

mat, number of channels, and sampling frequency is

displayed.

To adjust the volume, use the MASTER VOLUME

control.

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ 35)

• “Audyssey” (➔ 48)

Information is displayed for about three seconds, then the pre-

viously displayed information reappears.

■ Operating with the remote controller

Setting the Display Brightness

Press RECEIVER followed by INPUT SELEC-

TOR.

You can adjust the brightness of the AV receiver’s display.

Start playback on the source component.

See also:

Press RECEIVER followed by DIMMER repeat-

edly to select:

• “Controlling Other Components” (➔ 76)

• “Controlling iPod” (➔ 71)

• “Listening to the Radio” (➔ 32 )

• Normal + MASTER VOLUME indicator lights.

• Normal + MASTER VOLUME indicator goes off.

• Dim + MASTER VOLUME indicator goes off.

• Dimmer + MASTER VOLUME indicator goes

off.

To adjust the volume, use VOL q/w.

Select a listening mode and enjoy!

See also:

Tip

• “Using the Listening Modes” (➔ 35)

• “Audyssey” (➔ 48)

• Alternatively, you can use the AV receiver’s DIMMER.

Download from Www.Somanuals.com. All Manuals Search And Download.

Muting the AV Receiver

Using the Home Menu

You can temporarily mute the output of the AV receiver.

The Home menu provides you quick access to frequently

used menus without having to go through the long stan-

dard menu. This menu enables you to change settings and

view the current information.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator

flashes on the display.

Press RECEIVER followed by HOME.

The following information will be superimposed on

the TV screen.

Tip

• To unmute, press MUTING again or adjust the volume.

• The Mute function is cancelled when the AV receiver is set to

Standby.

BD/DVD

Audio

Bass

0dB

Video

Treble

Info

Input

Listening Mode

Subwoofer Level

Center Level

Dynamic EQ

Dynamic Volume

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn

off automatically after a specified period.

Use q/w/e/r to make the desired selection.

Press RECEIVER followed by SLEEP repeatedly

to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in

10 minute steps.

The SLEEP indicator lights on the display when the

sleep timer has been set. The specified sleep time

appears on the display for about 5 seconds, then the

previous display reappears.

■ Audio

`You can change the following settings: “Bass”,

“Treble”, “Subwoofer Level ”, “Center Level”,

“Dynamic EQ ”, “Dynamic V o lume ”, “Late

Night”, “Music Optimizer”, “Re-EQ”, “Re-

EQ(THX)”, and “Audio Selector”.

See also:

• “Audyssey” (➔ 48)

Tip

• “Using the Audio Settings” (➔ 56)

• If you need to cancel the sleep timer, press SLEEP repeatedly

until the SLEEP indicator goes off.

• To check the time remaining until the AV receiver sleeps, press

SLEEP. Note that if you press SLEEP while the sleep time is

being displayed, you’ll shorten the sleep time by 10 minutes.

■ Video

`You can change the following settings: “Wide

Mode”, “Picture Mode ”, “Brightness”, “Con-

trast”, “Hue” and “Saturation”.

The remote controller’s VIDEO acts as a short-

cut for this menu.

Selecting Speaker Layout

See also:

You can prioritize which speakers you want to use.

• “Picture Adjust” (➔ 51)

*3*4

■ Info

Press RECEIVER followed by SP LAYOUT

repeatedly.

`Speaker Layout:FH:

`You can view the information of the following

items: “Audio”, “Video”, and “Tuner”.

The sound from front high speakers is output

by priority.

`Speaker Layout:FW:

*4*5

■ Input

`You can select the input source while viewing

the information as follows: the name of input

selectors, input assignments, and radio informa-

tion, and ARC function setting.

The sound from front wide speakers is output

by priority.

`Speaker Layout:SB:

Press ENTER to display the current input

source, followed by q/w to select the desired

input source. Pressing ENTER again switches to

the selected input source.

The sound from surround back speakers is out-

put by priority.

Note

■ Listening Mode

• If the “Speakers Type(Front)” setting is set to “Bi-Amp”

(➔ 44), or Powered Zone 2 is being used (➔ 69), this setting

cannot be selected.

• When the listening mode that doesn’t support front high, front

wide or surround back speakers is used, the setting cannot be

selected.

`You can select the listening modes that are

grouped in the following categories: “MOVIE/

TV”, “MUSIC”, “GAME”, and “THX”.

Use q/w to select the category and e/r to

select the listening mode. Press ENTER to

switch to the selected listening mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

Using Headphones

If Pure Audio or Direct listening mode is selected,

Connect a pair of stereo headphones with a stan-

dard plug (1/4 inch or 6.3 mm) to the PHONES

jack.

“Dynamic EQ” and “Dynamic Volume” cannot be selected.

Only when you have selected “Custom” in the “Picture

Mode” (➔ 51), pressing ENTER allows you to adjust the fol-

lowing items via the Home menu; “Brightness”, “Contrast”,

“Hue”, and “Saturation”. Press RETURN to return to the

original Home menu.

Note

• Always turn down the volume before connecting your head-

phones.

Depending on the input source and listening mode, not all

channels shown here output the sound.

• While the headphones plug is inserted in the PHONES jack, the

Headphone indicator, speaker/channel indicator FL and FR

lights. (The Powered Zone 2 speakers are not turned off.)

• When you connect a pair of headphones, the listening mode is

set to Stereo, unless it’s already set to Stereo, Mono, Direct, or

Pure Audio.

When you have entered a custom name in “Name Edit”

(➔ 50), the input source is displayed with that name. But

even if not, the component name may be displayed if the AV

receiver receives it via HDMI connection (➔ 18).

For the PORT input selector, the name of Universal Port

Option Dock will be displayed.

• Only the Stereo, Direct, Pure Audio, and Mono listening modes

can be used with headphones.

Changing the Input Display

When you connect an u-capable Onkyo component, you

must configure the input display so that u can work

properly.

This setting can be done only from the front panel.

Press TV/CD, GAME or VCR/DVR so that “TV/

CD”, “GAME” or “VCR/DVR” appears on the

display.

Press and hold down TV/CD, GAME or VCR/DVR

(about 3 seconds) to change the input display.

Repeat this step to select “MD”, “CDR”, “DOCK”

or “TAPE”.

For the TV/CD input selector, the input display

changes in this order:

TV/CD → MD → CDR

→

TAPE

DOCK

For the GAME input selector, the setting changes in

this order:

GAME ↔ DOCK

For the VCR/DVR input selector, the setting

changes in this order:

VCR/DVR ↔ DOCK

Note

• DOCK can be selected for the TV/CD, GAME or VCR/DVR

input selector, but not at the same time.

• Enter the appropriate remote control code before using the

remote controller for the first time (➔ 76).

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning Off the Components

Using Easy Macros

Using the Easy macro command in the Easy macro mode,

you can sequentially operate Onkyo components with sim-

ple commands by simply pressing one button. The default

actions are described below. Press ACTIVITIES to start

the Easy macro command.

Once the AV receiver has entered the normal macro mode,

all of ACTIVITIES will automatically switch to the nor-

mal macro mode. In this case, pressing ALL OFF will set

only the AV receiver to Standby mode.

Press ALL OFF.

1. The connected component stops and turns off.

2. The AV receiver turns off.

3. The TV connected to the AV receiver turns off

*1*2

(Standby).

When MY MUSIC is selected, with the default settings, this

will not be performed.

With some televisions, the power may not be turned off (or

enter standby).

Press MY MOVIE, MY TV, or MY MUSIC.

MY MOVIE (default):

Changing Source Component

1. The TV connected to the AV receiver is turned

on.

2. The Onkyo DVD player connected to the AV

receiver is turned on.

When you want to operate the component that is not

assigned as the source component, you can assign it as the

source component.

3. The AV receiver is turned on.

4. The input selector of the AV receiver is set to

“BD/DVD”.

While holding down REMOTE MODE, press and

hold down MY MOVIE, MY TV, or MY MUSIC

(about 3 seconds).

ACTIVITIES that you pressed flashes twice, indicat-

ing that the setting has been established.

Examples:

When you press MY MUSIC and want to start the

Onkyo Cassette recorder, while holding down TV/

CD, press and hold down MY MUSIC (about 3 sec-

onds) flashes twice.

5. The player starts playback.

MY TV (default):

1. The TV connected to the AV receiver is turned

on.

2. The cable set-top box connected to the AV

receiver is turned on.

3. The AV receiver is turned on.

4. The input selector of the AV receiver is set to

“CBL/SAT”. You can enjoy cable TV.

Restoring Default

MY MUSIC (default):

1. The Onkyo CD player connected to the AV

receiver is turned on.

2. The AV receiver is turned on.

3. The input selector of the AV receiver is set to

“TV/CD”.

While holding down HOME, press and hold down

ALL OFF until ALL OFF lights (about 3 seconds).

Release HOME and ALL OFF and press ALL OFF

again.

ALL OFF flashes twice.

4. The player starts playback.

Note

• Once you start the Easy macro command, you cannot use

other ACTIVITIES during the execution. If you want to

operate other components halfway, press ALL OFF to

stop and press desired ACTIVITIES.

Depending on the start-up time of Blu-ray Disc/DVD player,

the AV receiver may not activate this playback command. In

this case, press 1 on the remote controller.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audyssey MultEQ^®Room Correction

and Speaker Setup

With the supplied calibrated microphone,

Audyssey MultEQ automatically determines the number

of speakers connected, their size for purposes of bass man-

agement, optimum crossover frequencies to the subwoofer

(if present), and distances from the primary listening posi-

tion.

d e f

c a b

Audyssey MultEQ then removes the distortion caused by

room acoustics by capturing room acoustical problems

over the listening area in both the frequency and time

domain. The result is clear, well-balanced sound for every-

one. Enabling Audyssey MultEQ allows you to also use

: Listening area

a to f: Listening position

Note

• Make the room as quiet as possible. Background noise and Radio

Frequency Interference (RFI) can disrupt the room measure-

ments. Close windows, televisions, radios, air conditioners, flu-

orescent lights, home appliances, light dimmers, or other

devices. Turn off the cell phone (even if it is not in use) or place

it away from all audio electronics.

• The microphone picks up test tones which played through each

speaker as Audyssey MultEQ^®Room Correction and Speaker

Setup run.

Audyssey Dynamic EQ , which maintains the proper

octave-to-octave balance at any volume level (➔ 48).

Before using this function, connect and position all of

your speakers.

If “Dynamic EQ” is set to “On” (➔ 48), the “Equalizer”

setting will be set to “Audyssey” (➔ 46). On the other

hand, if it is set to “Off”, the “Dynamic Volume” setting

will be set to “Off” (➔ 49).

• Audyssey MultEQ Room Correction and Speaker Setup cannot

be performed while a pair of headphones is connected.

It takes about 30 minutes to complete Audyssey MultEQ

Room Correction and Speaker Setup for 6 positions. Total

measurement time varies depending on the number of

speakers.

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV receiver

is connected.

Set the speaker setup microphone at the Main Lis-

tening Position a, and connect it to the SETUP

MIC jack.

Using Audyssey MultEQ

Using Audyssey MultEQ to create a listening environment

in your home theater that all listeners will enjoy,

Audyssey MultEQ takes measurements at up to 6 posi-

tions within the listening area. Position the microphone at

ear height of a seated listener with the microphone tip

pointed directly at the ceiling using a tripod. Do not hold

the microphone in your hand during measurements as this

will produce inaccurate results.

SETUP MIC jack

Speaker setup microphone

■ First measurement position

Also referred to as the Main Listening Position this

refers to the most central position where one would nor-

mally sit within the listening environment. MultEQ uses

the measurements from this position to calculate

speaker distance, level, polarity, and the optimum cross-

over value for the subwoofer.

The speaker setting menu appears.

Note

• The on-screen setup menus appear only on a TV that is

connected to the HDMI OUT. If your TV is connected to

the MONITOR OUT V, MONITOR OUT S or the COM-

PONENT VIDEO MONITOR OUT, use the AV

receiver’s display when changing settings.

^{■ Second}−Sixth measurement positions

These are the other listening positions (i.e., the places

where the other listeners will sit). You can measure up

to 6 positions.

The following examples show some typical home theater

seating arrangements. Choose the one that best matches

yours, and position the microphone accordingly when

prompted.

Download from Www.Somanuals.com. All Manuals Search And Download.

When you’ve finished making the settings, press

ENTER.

Use q/w to select an option, and then press

ENTER.

MultEQ: Auto Setup

- - Review Speaker Configuration - -

Speakers Type(Front)

Powered Zone2

Subwoofer

Normal

Not Act

Yes

Subwoofer

Front

Center

Surround

Front Wide

Front High

Surr Back

Surr Back Ch

Yes

40Hz

100Hz

None

100Hz

120Hz

2ch

• If your front speakers are bi-amped, you must

select “Bi-Amp ” in the “Speakers Type(Front)”

setting (➔ 44). For hookup information, see “Bi-

amping the Front Speakers” (➔ 16).

• If you change “Powered Zone2” setting, refer to

“Setting the Powered Zone 2” for more details

(➔ 69).

• If you are using a subwoofer(s), select “Yes” in the

“Subwoofer” (➔ 44). If not, select “No” and skip

step 4.

Save

Cancel

The options are:

`Save:

Save the calculated settings and exit

Audyssey MultEQ Room Correction and Speaker

Setup.

`Cancel:

If you use a powered subwoofer(s), adjust the sub-

woofer volume level to 75dB.

Cancel Audyssey MultEQ Room Correction and

Speaker Setup.

Test tones are played through the subwoofer. Use the

volume control on the subwoofer.

Note

• You can view the calculated settings for the speaker con-

figuration, speaker distances, and speaker levels by using

e/r.

Note

• If your subwoofer does not have a volume control, disre-

gard the level displayed and press ENTER to proceed to

the next step.

• If you set the subwoofer’s volume control to its maximum

and the displayed level is lower than 75 dB, leave the sub-

woofer’s volume control at its maximum and press

ENTER to proceed to the next step.

Disconnect the speaker setup microphone.

Note

• When Audyssey MultEQ Room Correction and Speaker Setup is

complete, the “Equalizer” will be set to “Audyssey” (➔ 46).

The Audyssey indicator will light (➔ 9).

• You can cancel Audyssey MultEQ Room Correction and

Speaker Setup at any point in this procedure simply by discon-

necting the setup microphone.

• Do not connect or disconnect any speakers during

Audyssey MultEQ Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically

when Audyssey MultEQ Room Correction and Speaker Setup

starts.

• Changes to the room after Audyssey MultEQ Room Correction

and Speaker Setup requires you run Audyssey MultEQ Room

Correction and Speaker Setup again, as room EQ characteristics

may have changed.

Press ENTER.

Audyssey MultEQ Room Correction and Speaker

Setup starts.

Test tones are played through each speaker as

Audyssey MultEQ Room Correction and Speaker

Setup runs. This process takes a few minutes. Please

refrain from talking during measurements and do

not stand between speakers and the microphone.

Do not disconnect the speaker setup microphone

during Audyssey MultEQ Room Correction and

Speaker Setup, unless you want to cancel the setup.

Place the setup microphone at the next position,

and then press ENTER.

Audyssey MultEQ performs more measurements.

This takes a few minutes.

When prompted, repeat step 6.

Download from Www.Somanuals.com. All Manuals Search And Download.

Error Messages

Changing the Speaker Settings Manually

While Audyssey MultEQ Room Correction and Speaker

Setup is in progress, one of the error messages below may

appear.

You can manually make changes to the settings found dur-

ing Audyssey MultEQ Room Correction and Speaker

Setup.

See also:

MultEQ: Auto Setup

• “Speaker Configuration” (➔ 44)

• “Speaker Distance” (➔ 45)

• “Level Calibration” (➔ 45)

• “Equalizer Settings” (➔ 46)

Ambient noise is too high.

Note

• Please note that THX recommends any THX main speakers be

set to “80Hz(THX)”. If you set up your speakers using

Audyssey MultEQ Room Correction and Speaker Setup,

please make sure manually that any THX speakers are set to

80 Hz (THX) crossover (➔ 44).

Retry

Cancel

Error message

The options are:

`Retry:

Try again.

`Cancel:

• Sometimes due to the electrical complexities of subwoofers and

the interaction with the room, THX recommends setting the level

and the distance of the subwoofer manually.

• Sometimes due to interaction with the room, you may notice

irregular results when setting the level and/or distance of the

main speakers. If this happens, THX recommends setting them

manually.

Cancel Audyssey MultEQ Room Correction and

Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of

the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different from

that of the first measurement. Check the speaker con-

nection.

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very

low-frequency sound at a low volume level, it may not be

detected by Audyssey MultEQ Room Correction and

Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker

Configuration” screen as “No”, increase the subwoofer’s

volume to the half-way point, set it to its highest crossover

frequency, and then try running Audyssey MultEQ Room

Correction and Speaker Setup again. Note that if the vol-

ume is set too high and the sound distorts, detection issues

may occur, so use an appropriate volume level. If the sub-

woofer has a low-pass filter switch, set it to Off or Direct.

Refer to your subwoofer’s instruction manual for details.

• Writing Error!

This message appears if saving fails. Try saving again.

If this message appears after 2 or 3 attempts, contact

your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No”

means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (➔ 13).

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio

■ Manual tuning mode

This section describes the procedure using the but-

tons on the front panel unless otherwise specified.

Press TUNING MODEso that the AUTO indicator

goes off on the display.

Using the Tuner

Press and hold TUNING q/w.

The frequency stops changing when you release the

button.

With the built-in tuner you can enjoy AM and FM radio

stations. You can store your favorite stations as presets for

quick selection.

This model changes FM/AM frequency in 200/10kHz (or

50/9kHz) steps (➔ 53).

Press the buttons repeatedly to change the frequency

one step at a time.

In manual tuning mode, FM stations will be in mono.

Listening to the Radio

Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be

impossible to get good reception. In this case, switch to

manual tuning mode and listen to the station in mono.

Press TUNER to select either “AM” or “FM”.

In this example, FM has been selected.

Each time you press TUNER, the radio band

changes between AM and FM.

■ Tuning into stations by frequency

You can tune into AM and FM stations directly by enter-

ing the appropriate frequency.

Band

Frequency

On the remote controller, press TUNER repeat-

edly to select “AM” or “FM”, followed by D.TUN.

(Actual display depends on the country.)

Tuning into Radio Stations

■ Auto tuning mode

(Actual display depends on the country.)

Within 8 seconds, use the number buttons to enter

the frequency of the radio station.

For example, to tune to 87.50 (FM), press 8, 7, 5, 0.

If you have entered the wrong number, you can retry

after 8 seconds.

Press TUNING MODE so that the AUTO indicator

lights on the display.

Press TUNING q/w.

Searching stops when a station is found.

When tuned into a station, the TUNED indicator lights.

When tuned into a stereo FM station, the FM STEREO

indicator lights on the display, as shown.

TUNED

AUTO

FM STEREO

Download from Www.Somanuals.com. All Manuals Search And Download.

Presetting FM/AM Stations

You can store a combination of up to 40 of your favorite

FM/AM radio stations as presets.

Tune into the FM/AM station that you want to

store as a preset.

See the previous section.

Press MEMORY.

The preset number flashes.

While the preset number is flashing (about 8 sec-

onds), use PRESET e/r to select a preset from 1

through 40.

Press MEMORY again to store the station or chan-

nel.

The station or channel is stored and the preset num-

ber stops flashing.

Repeat this procedure for all of your favorite FM/

AM radio stations.

Note

• You can name your radio presets for easy identification (➔ 50).

Its name is displayed instead of the band and frequency.

Selecting Presets

To select a preset, use PRESET e/r on the AV

receiver, or the remote controller’s CH +/–.

Tip

• You can also use the remote controller’s number buttons to select

a preset directly.

Deleting Presets

Select the preset that you want to delete.

See the previous section.

While holding down MEMORY, press TUNING

MODE.

The preset is deleted and its number disappears from

the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

This section explains how to record the selected input source to a component with recording capability, and how to record

audio and video from different sources.

Connecting a Recording Component

On the source component, start playback.

If you select another input source during recording,

that input source will be recorded.

Recording Separate AV Sources

Here you can record audio and video from completely

separate sources, allowing you to overdub audio onto your

video recordings. This function takes advantage of the fact

that when an audio-only input source (TV/CD, TUNER or

PHONO) is selected, the video input source remains

unchanged.

In the following example, audio from the CD player con-

nected to the TV/CD IN and video from the camcorder

connected to the AUX INPUT VIDEO jack are recorded

by the VCR connected to the VCR/DVR OUT jacks.

AUDIO

VIDEO

Cassette, CDR, MD,

etc.

VCR, DVD recorder

Camcorder

Note

• The AV receiver must be turned on for recording. Recording is

not possible while it’s in Standby mode.

• If you want to record directly from your TV or playback VCR to

the recording VCR without going through the AV receiver, con-

nect the TV/VCR’s audio and video outputs directly to the

recording VCR’s audio and video inputs. See the manuals sup-

plied with your TV and VCR for details.

• Video signals connected to composite video inputs can be

recorded only via composite video outputs. If your TV/VCR is

connected to a composite video input, the recording VCR must

be connected to a composite video output.

• The surround sound and DSP listening modes cannot be

recorded.

• Copy-protected Blu-ray Disc/DVDs cannot be recorded.

• Sources connected to a digital input cannot be recorded. Only

analog inputs can be recorded.

• DTS signals will be recorded as noise, so don’t attempt analog

recording of DTS CDs or LDs.

• While the listening mode is set to Pure Audio, no image is pro-

vided because the power is turned off for the video circuit. If you

want to make recordings, select other listening mode.

CD player

VCR

: Video signal

: Audio signal

AV Recording

Audio sources can be recorded to a recorder (e.g., cassette

deck, CDR, MD) connected to the VCR/DVR OUT jacks.

Video sources can be recorded to a video recorder (e.g.,

VCR, DVD recorder) connected to the VCR/DVR OUT

jack.

Prepare the camcorder and CD player for play-

back.

Prepare the VCR for recording.

Press AUX input selector.

Use the input selector buttons to select the source

that you want to record.

Press TV/CD input selector.

This selects the CD player as the audio source, but

leaves the camcorder as the video source.

You can watch the source while recording. The AV

receiver’s MASTER VOLUME control has no effect

on recording.

Start recording on the VCR and start playback on

the camcorder and CD player.

The video from the camcorder and the audio from

the CD player are recorded by the VCR.

On your recorder, start recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Listening Modes

Selecting Listening Modes

See “About Listening Modes” for detailed information about the listening modes (➔ 36).

Listening Mode Buttons

Press RECEIVER first.

MOVIE/TV, MUSIC, GAME

PURE AUDIO button and indicator

MUSIC

GAME

THX

MOVIE/TV

MOVIE/TV button

PURE AUDIO button and indicator

This button selects the listening modes intended for use

with movies and TV.

This button selects the Pure Audio listening mode.

When this mode is selected, the AV receiver’s display

and video circuitry are turned off. Only video signals

input through HDMI IN can be output from HDMI

OUT. The indicator lights when this mode is selected.

Pressing this button again will select the previous listen-

ing mode.

MUSIC button

This button selects the listening modes intended for use

with music.

GAME button

This button selects the listening modes intended for use

with video games.

THX button

This button selects the THX listening modes.

• The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV

receiver with a digital audio connection (coaxial, optical, or HDMI).

• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source

Information” (➔ 25).

• While a pair of headphones is connected, you can select the following listening modes: Pure Audio, Mono, Direct, and Stereo.

• The listening modes cannot be used while you are listening to sound through your TV speakers coming from components

connected to the AV receiver (“TV Sp On” appears on the front panel).

Download from Www.Somanuals.com. All Manuals Search And Download.

About Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidel-

ity and stunning surround sound.

Explanatory Notes

SP LAYOUT

a b Front speakers

Center speaker

d e Surround speakers

Subwoofer(s)

LISTENING

MODE

g h Surround back speakers

i j Front high speakers

k l Front wide speakers

de gh

■ Input Source

The following audio formats are supported by the listening mode.

This is mono (monophonic) sound.

This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two

speakers.

This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth sub-

woofer channel (called the point-one channel).

This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two

additional speakers that provide greater sound envelopment and more accurate positioning of sounds.

This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth

channel from existing DTS 5.1 encoded material.

This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel

sources.

■ Speaker Layout

The illustration shows which speakers are activated in each channel. See “Speaker Configuration” for the speaker setup

(➔ 44).

Press RECEIVER followed by SP LAYOUT repeatedly to select the speakers you want to use; front high, front wide, or

surround back.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening Modes

Listening Mode

Description

Input

Source

Speaker

Layout

Pure Audio

In this mode, the display and video circuitry are turned off, minimizing pos-

sible noise sources for the ultimate in high-fidelity audio reproduction. (As

the video circuitry is turned off, only video signals input through HDMI IN

can be output from HDMI OUT.

ZXC

P u r e A A u d i o

Direct

In this mode, audio from the input source is output without surround-sound

processing. The “Speaker Configuration” (presence of speakers),

“Speaker Distance” and “A/V Sync” settings are enabled, but much of the

processing set via HOME is disabled. See “Advanced Setup” for more

details (➔ 41).

D i r e c t d i o P P o P P

Stereo

Sound is output by the front left and right speakers and subwoofer.

ZXC

S t e r e o d i o P P o P P

Mono

Use this mode when watching an old movie with a mono soundtrack, or use

it with the foreign language soundtracks recorded in the left and right chan-

nels of some movies. It can also be used with DVDs or other sources contain-

ing multiplexed audio, such as karaoke DVDs.

M o n o e o d i o P P o P P

Multichannel

This mode is for use with PCM multichannel sources.

XCN

M u l

i c h i o P P o P P

Dolby Pro Logic IIx^*2Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel play-

Dolby Pro Logic II

back. It provides a very natural and seamless surround-sound experience that

fully envelops the listener. As well as music and movies, video games can

also benefit from the dramatic spatial effects and vivid imaging. If you’re not

using any surround back speakers, Dolby Pro Logic II will be used instead

of Dolby Pro Logic IIx.

• Dolby PLIIx Movie

Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g.,

TV, DVD, VHS).

P L b M o v i e P P P P

P L b M u s i c P P P P

P L b G a m e c P P c P P

P L x GM o v i e P

P L x GM u s i c P

• Dolby PLIIx Music

Use this mode with any stereo or Dolby Surround (Pro Logic) music source

(e.g., CD, radio, cassette, TV, VHS, DVD).

• Dolby PLIIx Game

P L x GG a m e c P c P

Use this mode with video games, especially those that bear the Dolby Pro

Logic II logo.

• Dolby PLIIx Movie and Dolby PLIIx Music

These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel

sources for 7.1-channel playback.

Dolby Pro Logic IIz

Height

Dolby Pro Logic IIz Height is designed to more effectively use existing

program material when height channel speaker outputs are present. Dolby

Pro Logic IIz Height can be used to upmix a variety of sources from movies

and music, but are particularly well-suited to upmix game content.

P L z GH e i g h t

Dolby EX

These modes expand 5.1-channel sources for 6.1/7.1-channel playback.

They’re especially suited to Dolby EX soundtracks that include a matrix-

encoded surround back channel. The additional channel adds an extra dimen-

sion and provides an enveloping surround sound experience, perfect for

rotating and fly-by sound effects.

D o l b y c E X o P P o P P

D o l b y c D i E X P

Dolby Digital

In this mode, audio from the input source is output without surround-sound

processing. “Speaker Configuration” (presence of speakers), “Speaker

Distance”, “A/V Sync” and much of the processing set via HOME are

enabled. See “Advanced Setup” for more details (➔ 41).

XCN

D o l b y c D i o P P o P P

Dolby Digital Plus^*5

XCN

D o l b y c D o P P o P P

Dolby TrueHD

XCN

D D Tl r u e H D P P P P P P

DTS

XCN

D T S

d i o P P o P P

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening Mode

Description

Input

Source

Speaker

Layout

DTS-HD High

Resolution Audio

(Continued from the previous page.)

XCN

D T S – H D H R

DTS-HD Master

Audio

XCN

D T S – H D MS T R

DTS Express

XCN

D T S E x p r e s s

DSD^*6

D S D

DTS 96/24^*7

This mode is for use with DTS 96/24 sources. This is high-resolution DTS

with a 96 kHz sampling rate and 24-bit resolution, providing superior fidel-

ity. Use it with DVDs that bear the DTS 96/24 logo.

D T S e 9 6 / 2 4 P P P P

DTS-ES Discrete^*8

This mode is for use with DTS-ES Discrete soundtracks, which use a dis-

crete surround back channel for true 6.1/7.1-channel playback. The seven

totally separate audio channels provide better spatial imaging and 360-

degree sound localization, perfect for sounds that pan across the surround

channels. Use it with DVDs that bear the DTS-ES logo, especially those with

a DTS-ES Discrete soundtrack.

E S S D i s c r e t e

DTS-ES Matrix^*8

This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-

encoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that

bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.

E S SM a t

i x t e t e

DTS Neo:6

This mode expands any 2-channel source for up to 7.1-channel playback. It

uses seven full-bandwidth channels of matrix decoding for matrix-encoded

material, providing a very natural and seamless surround sound experience

that fully envelops the listener.

• Neo:6 Cinema

Use this mode with any stereo movie (e.g., TV, DVD, VHS).

• Neo:6 Music

XCN

N e o : 6 t

i x t e x t e

N e o : 6 t Cr i nx et me ax t e

N e o : 6 t M u s i c

Use this mode with any stereo music source (e.g., CD, radio, cassette, TV,

VHS, DVD).

This mode uses Neo:6 to expand 5.1-channel sources for 6.1/7.1-channel

playback.

Audyssey DSX^*9

™

Audyssey DSX is a scalable system that adds new speakers to improve sur-

round impression. Starting with a 5.1 system Audyssey DSX first adds Wide

channels for the biggest impact on envelopment. Research in human hearing

has proven that information from the Wide channels is much more critical in

the presentation of a realistic soundstage than then Back Surround channels

found in traditional 7.1 systems. Audyssey DSX then creates a pair of Height

channels to reproduce the next most important acoustical and perceptual

cues. In addition to these new Wide and Height channels, Audyssey DSX

applies Surround Envelopment Processing to enhance the blend between the

front and surround channels.

A u d y s s e y D S X

P L b M o v i e D S X

P L b M u s i c D S X

P L b G a m e D S X

N e o : 6 Ct Cr i nx t De Sx Xt e

N e o : 6 t M u s D S X

The combination of Dolby Pro Logic II and Audyssey DSX modes can be

used.

The combination of Neo:6 Cinema/Music and Audyssey DSX modes can

be used.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening Mode

Description

Input

Source

Speaker

Layout

THX

Founded by George Lucas, THX develops stringent standards that ensure

movies are reproduced in movie theaters and home theaters just as the direc-

tor intended. THX Modes carefully optimize the tonal and spatial character-

istics of the soundtrack for reproduction in the home-theater environment.

They can be used with 2-channel matrixed and multichannel sources. Sur-

round back speaker output depends on the source material and the selected

listening mode.

T H X e C i n e m a P

NT He Xo e: M6 ut sr i xc at Pe x at Pe

T H X e G a m e s a P a P

NT He Xo e: S6 2t mr Ci xi nt e mx at e

T H X e S 2 mM u s i c

T H X e S 2 mG a m e s

T H X e S u r r a E X a

• THX Cinema

THX Cinema mode corrects theatrical soundtracks for playback in a home

theater environment. In this mode, THX Loudness Plus is configured for

cinema levels and Re-EQ, Timbre Matching, and Adaptive Decorrelation

are active.

• THX Music

THX Music mode is tailored for listening to music, which is typically mas-

tered at significantly higher levels than movies. In this mode, THX Loud-

ness Plus is configured for music playback and only Timbre Matching is

active.

• THX Games

THX Games mode is meant for spatially accurate playback of game audio,

which is often mixed similarly to movies but in a smaller environment. THX

Loudness Plus is configured for game audio levels, with Timbre Matching

active.

The combination of Dolby Pro Logic II/IIx and THX Cinema/Music/

Games modes can be used.

The combination of Dolby Pro Logic IIz Height and THX Cinema/

Music/Games modes can be used.

The combination of DTS Neo:6 and THX Cinema/Music/Games modes

can be used.

• THX Select2 Cinema

This mode expands 5.1-channel sources for 7.1- channel playback. It does

this by analyzing the composition of the surround source, optimizing the

ambient and directional sounds to produce the surround back channel out-

put.

• THX Select2 Music

This mode is designed for use with music. It expands 5.1-channel sources

for 7.1-channel playback.

• THX Select2 Games

This mode is designed for use with video games. It can expand 5.1-channel

sources for 6.1/7.1-channel playback.

• THX Surround EX

This mode expands 5.1-channel sources for 6.1/7.1- channel playback. It’s

especially suited to Dolby Digital EX sources. THX Surround EX, also

known as Dolby Digital Surround EX, is a joint development between

Dolby Laboratories and THX Ltd.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onkyo-Original DSP Listening Modes

Listening Mode

Description

Input

Source

Speaker

Layout

Orchestra

Suitable for classical or operatic music, this mode emphasizes the surround

channels in order to widen the stereo image, and simulates the natural rever-

beration of a large hall.

*10

O r c h e s t r a

Unplugged

Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the

front stereo image, giving the impression of being right in front of the stage.

U n p l u g g e d

Studio-Mix

Suitable for rock or pop music, listening to music in this mode creates a

lively sound field with a powerful acoustic image, like being at a club or rock

concert.

S t u d i o – M i x

TV Logic

This mode adds realistic acoustics to TV shows produced in a TV studio,

surround effects to the entire sound, and clarity to voices.

T V L o g i c

Game-RPG

Use this mode when playing role playing game discs.

Use this mode when playing action game discs.

Use this mode when playing rock game discs.

Use this mode when playing sports game discs.

G a m e – R P G

Game-Action

G a m e – A c t i o n

Game-Rock

G a m e – R o c k

Game-Sports

G a m e – S p o r t s

All Ch Stereo

Ideal for background music, this mode fills the entire listening area with ste-

reo sound from the front, surround, and surround back speakers.

*10

XCN

A l

C h S t e r e o

Full Mono

In this mode, all speakers output the same sound in mono, so the sound you

hear is the same regardless of where you are within the listening room.

F u l

M o n o

T-D (Theater-

Dimensional)

With this mode you can enjoy a virtual surround sound even with only two or

three speakers. This works by controlling how sounds reach the listener’s left

and right ears. Good results may not be possible if there’s too much reverb,

so we recommend that you use this mode in an environment with little or no

natural reverb.

ZXC

T – D

Note

Based on the audio channels contained in the source, the corresponding speakers will output the sound.

If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used.

Surround back and front wide speakers are not supported.

Front high and front wide speakers are not supported.

For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.

AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better

sound according to the player. In that case, set the output setting on the player side to PCM.

DTS is used depending on the configuration of the A V r eceiver (e.g., Audyssey Dynamic EQ is on).

If there are no surround back speakers, DTS is used.

• This listening mode can be selected only when all the following conditions are satisfied:

a. Center speaker is connected.

b. Either of front high or front wide speakers is connected.

• Output can be switched between front high or front wide speakers by pressing SP LAYOUT [depending on the

“Speaker Configuration” setting (➔ 44)].

*10

Output can be switched between front high, front wide or surround back speakers by pressing SP LAYOUT [depending on the

“Speaker Configuration” setting (➔ 44)].

• The listening modes cannot be selected with some source formats.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Advanced Setup

On-screen Setup Menus

Common Procedures in Setup Menu

The on-screen setup menus appear only on a TV that

is connected to the HDMI OUT. If your TV is con-

nected to the MONITOR OUT V, MONITOR OUT S

or the COMPONENT VIDEO MONITOR OUT, use

the AV receiver’s display when changing settings.

RECEIVER

ENTER

q/w/e/r

This manual describes the procedure using the

remote controller unless otherwise specified.

SETUP

RETURN

1. Input/Output Assign

2. Speaker Setup

3. Audio Adjust

4. Source Setup

5. Listening Mode Preset

6. Miscellaneous

7. Hardware Setup

8. Remote Controller Setup

9. Lock Setup

The on-screen setup menus appear on the connected TV

and provide a convenient way to change the AV receiver’s

various settings. Settings are organized into 9 categories

on the main menu.

Carry out the settings by using the on-screen display.

Press RECEIVER followed by SETUP.

The following menu appears.

a Input/Output Assign f Miscellaneous

(➔ 42)

(➔ 53)

1. Input/Output Assign

6. Miscellaneous

1. Input/Output Assign

2. Speaker Setup

3. Audio Adjust

4. Source Setup

5. Listening Mode Preset

6. Miscellaneous

7. Hardware Setup

8. Remote Controller Setup

9. Lock Setup

1. Monitor Out

2. HDMI Input

3. Component Video Input

4. Digital Audio Input

5. Analog Audio Input

1. Volume Setup

2. OSD Setup

b Speaker Setup

g Hardware Setup

(➔ 44)

(➔ 53)

Tip

2. Speaker Setup

7. Hardware Setup

• If the main menu doesn’t appear, make sure the appropri-

ate external input is selected on your TV.

1. Speaker Settings

2. Speaker Configuration

3. Speaker Distance

4. Level Calibration

5. Equalizer Settings

6. THX Audio Setup

1. Remote ID

2. Tuner

3. HDMI

4. Auto Power Down

5. Network

6. Firmware Update

Use q/w to select a menu, and then press ENTER.

Use q/w to select target and then press ENTER.

c Audio Adjust

h Remote Controller

(➔ 47)

Setup (➔ 76)

Use q/w to select option and use e/r to change

the setting.

3. Audio Adjust

8. Remote Controller Setup

Remote Mode Setup

1. Multiplex/Mono

2. Dolby

3. DTS

4. Audyssey DSX

5. Theater-Dimensional

6. LFE Level

Press SETUP to close the menu.

Press RETURN to return to the previous menu.

Note

d Source Setup (➔ 48) i Lock Setup (➔ 56)

• This procedure can also be performed on the AV receiver by

using SETUP, arrow buttons, and ENTER.

• During Audyssey MultEQ^®Room Correction and Speaker

Setup, messages, etc., that are displayed on the TV screen will

appear in the Display.

4. Source Setup

9. Lock Setup

Setup

1. Audyssey

2. IntelliVolume

3. A/V Sync

4. Name Edit

5. Picture Adjust

e Listening Mode Preset

(➔ 52)

5. Listening Mode Preset

1. BD/DVD

2. VCR/DVR

3. CBL/SAT

4. GAME

5. PC

6. AUX

Download from Www.Somanuals.com. All Manuals Search And Download.

Explanatory Notes

HDMI Input

If you connect a video component to an HDMI input, you

must assign that input to an input selector. For example, if

you connect your Blu-ray Disc/DVD player to HDMI

IN 2, you must assign “HDMI2” to the “BD/DVD” input

selector.

Main menu

Speaker Setup

■ Subwoofer

`Yes:

Select if a subwoofer is connected.

`No:

Select if no subwoofer is connected.

If you’ve connected your TV to the AV receiver with an

HDMI cable, composite video, S-video and component

video sources can be upconverted and output by the

HDMI OUT. You can set this for each input selector by

selecting the “- - - - -” option.

a Menu selection

b Setting target

Composite video, S-Video,

c Setting options (default setting underlined)

component video

HDMI

Input/Output Assign

Main Menu

Input/Output Assign

OUT

Composite video, S-Video,

Monitor Out

component video

You can specify the output resolution for the HDMI OUT

and COMPONENT VIDEO MONITOR OUT and have

the AV receiver upconvert the picture resolution as neces-

sary to match the resolution supported by your TV.

Here are the default assignments.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

HDMI1

■ Resolution

`Through:

Select this to pass video through the AV receiver at

the same resolution and with no conversion.

`Auto:

HDMI2

HDMI3

HDMI4

HDMI5

AUX

FRONT (Fixed)

- - - - - (Fixed)

- - - - -

Select this to have the AV receiver automatically

convert video at resolutions not supported by your

TV.

TUNER

TV/CD

PHONO

PORT

- - - - -

`480p:

- - - - -

Select this for 480p output and video conversion as

necessary.

`720p:

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,

TV/CD, PHONO, PORT

Select this for 720p output and video conversion as

`HDMI1, HDMI2, HDMI3, HDMI4, HDMI5:

Select the HDMI IN to which the video component

has been connected.

necessary.

`1080i:

Select this for 1080i output and video conversion as

necessary.

`- - - - -:

Output composite video, S-Video, and component

video sources from the HDMI OUT. The video out-

put signal from the HDMI OUT is the one config-

ured in “Component Video Input” (➔ 43).

• “AUX” is used only for input from the front panel.

• Each HDMI input cannot be assigned to two input selec-

tors or more. When HDMI1 - HDMI5 have already

been assigned, you must set first any unused input selec-

tors to “- - - - -” or you will be unable to assign HDMI1

- HDMI5 to input selector.

`1080p:

Select this for 1080p output and video conversion as

necessary.

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Audio Input

Note

• If no video component is connected to HDMI OUT (even if the

HDMI input is assigned), the AV receiver selects the video

source based on the setting of “Component Video Input”.

• When an HDMI IN is assigned to an input selector as explained

here, the same HDMI IN will be set as a priority in the “Digital

Audio Input” (➔ 43). In this case, if you want to use the coaxial

or optical audio input, make the selection in the Audio Selector

in the Home menu (➔ 26).

• “TUNER” selector cannot be assigned and is fixed at the

“- - - - -” option.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to UNIVERSAL PORT jack, you cannot assign any input

to “PORT” selector.

If you connect a component to a digital audio input, you

must assign that input to an input selector. For example, if

you connect your CD player to the OPTICAL IN 1, you

must assign “OPT1” to the “TV/CD” input selector.

Here are the default assignments.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

COAX1

COAX2

COAX3

OPT1

- - - - -

• Do not assign the component connected with the HDMI input to

“TV/CD” selector when you set “TV Control” setting to “On”

(➔ 55). Otherwise, appropriate CEC (Consumer Electronics

Control) operation will not be guaranteed.

AUX

- - - - -

TUNER

TV/CD

- - - - - (Fixed)

OPT2

PHONO

PORT

- - - - -

Component Video Input

- - - - -

If you connect to a COMPONENT VIDEO IN, you must

assign it to an input selector. For example, if you connect

your Blu-ray Disc/DVD player to COMPONENT

VIDEO IN 2, you should assign it to the “BD/DVD” input

selector.

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,

TV/CD, PHONO, PORT

`COAX1, COAX2, COAX3, OPT1, OPT2:

Select a corresponding digital audio input that the

component has been connected.

Here are the default assignments.

`- - - - -:

Select if the component is connected to an analog

audio input.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

IN1

- - - - -

Note

IN2

• When an HDMI IN is assigned to an input selector in “HDMI

Input” (➔ 42), the same HDMI IN will be set as a priority in this

assignment. In this case, if you want to use the coaxial or optical

audio input, make the selection in the Audio Selector in the

Home menu.

• Available sampling rate for PCM signals from a digital input

(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any

input to “PORT” selector.

- - - - -

AUX

- - - - -

TUNER

TV/CD

- - - - - (Fixed)

- - - - -

PHONO

PORT

- - - - -

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,

TV/CD, PHONO, PORT

Analog Audio Input

`IN1, IN2:

Some DVD players output the LFE channel from their

analog subwoofer output at 15 dB higher than normal.

With this setting, you can change the AV receiver’s sub-

woofer sensitivity to match your DVD player.

Select a corresponding component video input that

the video component has been connected.

`- - - - -:

Select if you are using HDMI OUT, rather than the

COMPONENT VIDEO MONITOR OUT, for the

output from composite video, S-Video, and compo-

nent video sources.

■ Subwoofer Input Sensitivity

`0dB to 15dB in 5 dB step.

Note

• This setting only affects signals connected to the AV receiver’s

multichannel input: SUBWOOFER jack.

• If you find that your subwoofer is too loud, try the 10 dB or

15 dB setting.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any

input to “PORT” selector.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Configuration

Speaker Setup

Main menu

Speaker Setup

This setting is set automatically by Audyssey MultEQ

Room Correction and Speaker Setup function (➔ 29).

Some of the settings in this section are set automatically

by Audyssey MultEQ Room Correction and Speaker

Setup function (➔ 29).

With these settings, you can specify which speakers are

connected and a crossover frequency for each speaker.

Specify “Full Band” for speakers that can output low fre-

quency bass sounds adequately, for example, speakers

with a good sized woofer. For smaller speakers, specify a

crossover frequency. Sounds below the crossover fre-

quency will be output by the subwoofer instead of the

speaker. Refer to your speaker’s manuals to determine the

optimum crossover frequencies. If you set up your speak-

ers using Audyssey MultEQ Room Correction and

Speaker Setup, please make sure manually that any THX

speakers are set to “80Hz(THX)” crossover.

Here you can check the settings made by

Audyssey MultEQ Room Correction and Speaker Setup

function, or set them manually, which is useful if you

change one of the connected speakers after using

Audyssey MultEQ Room Correction and Speaker Setup

function.

Note

• These settings are disabled when:

– a pair of headphones is connected, or

– the “Audio TV Out” setting is set to “On” (➔ 54) and an

input selector other than HDMI is selected.

■ Subwoofer

`Yes:

Speaker Settings

Select if a subwoofer is connected.

`No:

Select if no subwoofer is connected.

If you change these settings, you must run

Audyssey MultEQ Room Correction and Speaker

Setup again (➔ 29).

■ Front

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

If the impedance of any speaker is 4 ohms or more but less

than 6, set the minimum speaker impedance to 4 ohms.

If you bi-amp the front speakers, you must change the

“Speakers Type(Front)” setting (➔ 44).

For hookup information, see “Bi-amping the Front Speak-

ers” (➔ 16).

Note

• If the “Subwoofer” setting is set to “No”, the “Front” setting is

fixed at “Full Band”.

*2*3*4*5

■ Center , Surround , Surr Back

`Full Band

Note

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

• When bi-amping is used, the AV receiver is able to drive up to

5.1 speakers in the main room.

• Before you change these settings, turn down the volume.

`None:

Select if no speaker is connected.

■ Speaker Impedance

`4ohms:

*1*2*4*6 *1*2*4*5

, Front High

■ Front Wide

Select if the impedance of any speaker is 4 ohms or

more but less than 6.

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

`6ohms:

200Hz

Select if the impedances of all speakers are between

6 and 16 ohms.

`None:

Select if no speaker is connected.

■ Speakers Type(Front)

Note

`Normal:

“Full Band” can be selected only when “Full Band” is

selected in the “Front” setting.

If the “Surround” setting is set to “None”, this setting cannot

be selected.

If the “Surround” setting is set to anything other than “Full

Band”, “Full Band” cannot be selected here.

If the “Speakers Type(Front)” setting is set to “Bi-Amp”

(➔ 44), this setting cannot be selected.

If the Powered Zone 2 is being used (➔ 69), this setting can-

not be selected.

Select this if you’ve connected your front speakers

normally.

`Bi-Amp:

Select this if you’ve bi-amped your front speakers.

Note

• Powered Zone 2 cannot be used if “Speakers Type(Front)” is

set to “Bi-Amp” (➔ 69).

■ Powered Zone2

See “Setting the Powered Zone 2” (➔ 69).

If the “Powered Zone 2” setting is set to “Act” (➔ 69), this

setting cannot be selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Surr Back Ch

Speaker Distance

`1ch:

Select if only one surround back speaker is con-

nected.

`2ch:

This setting is set automatically by Audyssey MultEQ

Room Correction and Speaker Setup function (➔ 29).

Select if two (left and right) surround back speakers

are connected.

Here you can specify the distance from each speaker to the

listening position so that the sound from each speaker

arrives at the listener’s ears as the sound designer

intended.

Note

• If the “Surr Back” setting is set to “None” (➔ 44), this setting

cannot be selected.

■ Unit

■ LPF of LFE

`feet:

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

With this setting, you can specify the cutoff frequency

of the LFE channel’s low-pass filter (LPF), which can

be used to filter out unwanted hum. The LPF only

applies to sources that use the LFE channel.

Distances can be set in feet. Range: “0.5ft” to

“30.0ft” in 0.5 foot steps.

`meters:

Distances can be set in meters. Range: “0.15m” to

“9.00m” in 0.15 meter steps.

■ Left, Front Wide Left, Front High Left, Center,

Front High Right, Front Wide Right, Right, Surr

Right, Surr Back Right, Surr Back Left, Surr

Left, Subwoofer

■ Double Bass

This setting is NOT set automatically by

`Specify the distance from the each speaker to your lis-

tening position.

Audyssey MultEQ Room Correction and Speaker

Setup function (➔ 29).

Note

With the Double Bass function, you can boost bass out-

put by feeding bass sounds from the front left, right, and

center channels to the subwoofer.

`On:

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ 44).

Level Calibration

Double Bass function on.

`Off(THX):

This setting is set automatically by Audyssey MultEQ

Room Correction and Speaker Setup function (➔ 29).

Double Bass function off.

Note

Here you can adjust the level of each speaker with the

built-in test tone so that the volume of each speaker is the

same at the listening position.

• This function can be set only if the “Subwoofer” setting is set to

“Yes”, and the “Front” setting is set to “Full Band”.

• If you’re using THX-certified speakers, select “Off(THX)”.

■ Left, Front Wide Left, Front High Left, Center ,

Front High Right, Front Wide Right, Right, Surr

Right, Surr Back Right, Surr Back Left, Surr Left

`–12.0dB to 0.0dB to +12.0dB in 0.5 dB step.

■ Subwoofer

`–15.0dB to 0.0dB to +12.0dB in 0.5 dB step.

Note

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ 44).

• The speakers cannot be calibrated while the AV receiver is

muted.

• The test tone is output at the standard level for THX, which is

0 dB (absolute volume setting 82). If you normally listen at vol-

ume settings below this, be careful because the test tone will be

much louder.

For the center speaker and subwoofer, the level settings made

by using the Home menu are saved (➔ 26).

Tip

• If you’re using a handheld sound level meter, adjust the level of

each speaker so that it reads 75 dB SPL at the listening position,

measured with C-weighting and slow reading.

Download from Www.Somanuals.com. All Manuals Search And Download.

Equalizer Settings

THX Audio Setup

With the “Surr Back Speaker Spacing” setting, you can

specify the distance between your surround back speakers.

If you’re using a THX-certified subwoofer, set the “THX

Ultra2/Select2 Subwoofer” setting to “Yes”. You can

then apply THX’s Boundary Gain Compensation (BGC)

to compensate the perceived exaggeration of low frequen-

cies for listeners sitting very close to a room boundary

(i.e., wall).

This setting is set automatically by Audyssey MultEQ

Room Correction and Speaker Setup function (➔ 29).

With the Equalizer settings, you can adjust the tone of

speakers individually with a 7-band equalizer. The volume

of each speaker can be set (➔ 45).

■ Equalizer

You can also set the THX Loudness Plus. When the

“Loudness Plus” is set to “On”, it is possible to enjoy

even subtle nuances of audio expression at low volume.

This result is only available when the THX listening mode

is selected.

`Manual:

You can adjust the equalizer for each speaker manu-

ally. If you selected “Manual”, continue with this

procedure.

Press w to select “Channel”, and then use e/

■ Surr Back Speaker Spacing

`< 1ft (< 0.3m):

Select this if your surround back speakers are

between 0 and 1 foot (0–30 cm) apart.

`1ft - 4ft (0.3m - 1.2m):

Select this if your surround back speakers are

between 1 and 4 feet (0.3–1.2 m) apart.

`> 4ft (> 1.2m):

r to select a speaker.

Use q/w to select a frequency, and then use

the e/r to adjust the level at that frequency.

The volume at each frequency can be adjusted

from –6dB to 0dB to +6dB in 1 dB steps.

Note

• You can select: “63Hz”, “160Hz”, “400Hz”,

“1000Hz”, “2500Hz”, “6300Hz”, or “16000Hz”.

And for the subwoofer, “25Hz”, “40Hz”, “63Hz”,

“100Hz”, or “160Hz”.

• While the Direct or Pure Audio listening mode is

selected, the equalizer settings have no effect.

Select this if your surround back speakers are more

than 4 feet (1.2 m) apart.

Note

• Cannot be set if “Surr Back Ch” is set to “1ch” (➔ 45),

“Speakers Type(Front)” is set to “Bi-Amp” (➔ 44), “Surr

Back” is set to “None” (➔ 44), or Powered Zone 2 is being used

(➔ 69).

Tip

• Low frequencies (e.g., 63Hz) affect bass sounds;

high frequencies (e.g., 16000Hz) affect treble

sounds.

■ THX Ultra2/Select2 Subwoofer

`No:

Use q to select “Channel”, and then use e/r

Select this if you do not have a THX-certified sub-

woofer.

`Yes:

to select another speaker.

Repeat steps 1 and 2 for each speaker.

You cannot select speakers that you set to “No”

or “None” in the “Speaker Configuration”

(➔ 44).

Select this if you have a THX-certified subwoofer.

Note

• If the “Subwoofer” setting is set to “No”, this setting cannot be

selected (➔ 44).

`Audyssey:

This is selected automatically by Audyssey MultEQ

Room Correction and Speaker Setup function. The

Audyssey indicator will light (➔ 9) and

“Dynamic EQ” and “Dynamic Volume” become

available (➔ 48).

■ BGC

`Off:

Select this to turn off BGC.

`On:

Select this to turn on BGC.

`Off:

Note

Tone off, response flat.

• This setting is only available if “THX Ultra2/Select2 Sub-

woofer” is set to “Yes”.

■ Loudness Plus

`Off:

Select this to turn off Loudness Plus.

`On:

Select this to turn on Loudness Plus.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Preserve THX Settings

Input Channel

`Yes:

`Left + Right:

Audyssey Dynamic EQ /

Both the left and right channels are output.

Audyssey Dynamic Volume will not be active in

THX listening mode.

`No:

`Left:

Only the left channel is output.

`Right:

Audyssey Dynamic EQ/

Only the right channel is output.

Audyssey Dynamic Volume will be active in THX

listening mode depending on the setting.

Output Speaker

`Center:

Note

Mono audio is output by the center speaker.

• This setting is fixed at “Yes” if “Loudness Plus” is set to “On”.

`Left / Right:

Mono audio is output by the front left and right

speakers.

This setting determines which speakers output mono

audio when the Mono listening mode is selected.

THX Loudness Plus

THX Loudness Plus is a new volume control technology

featured in THX Ultra2 Plus™ and THX Select2 Plus™

Certified receivers. With THX Loudness Plus, home

theater audiences can now experience the rich details in

a surround mix at any volume level. A consequence of

turning the volume below Reference Level is that cer-

tain sound elements can be lost or perceived differently

by the listener. THX Loudness Plus compensates for the

tonal and spatial shifts that occur when the volume is

reduced by intelligently adjusting ambient surround

channel levels and frequency response. This enables

users experience the true impact of soundtracks regard-

less of the volume setting. THX Loudness Plus is auto-

matically applied when listening in any THX listening

mode. The new THX Cinema, THX Music, and THX

Games modes are tailored to apply the proper THX

Loudness Plus settings for each type of content.

Note

• If the “Center” setting is set to “None” (➔ 44), this setting is

fixed at “Left / Right”.

Dolby

■ PLIIx Music (2ch Input)

These settings apply to only 2-channel stereo sources.

If you’re not using any surround back speakers, these

settings apply to Dolby Pro Logic II, not Dolby Pro

Logic IIx.

Panorama

`On:

Panorama function on.

`Off:

Panorama function off.

Audio Adjust

With this setting, you can broaden the width of the front

stereo image when using the Dolby Pro Logic IIx Music

listening mode.

Main menu

Audio Adjust

With the Audio Adjust functions and settings, you can

adjust the sound and listening modes as you like.

Dimension

`–3 to 0 to +3

With this setting, you can move the sound field forward

or backward when using the Dolby Pro Logic IIx Music

listening mode. Higher settings move the sound field

backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much

surround sound, move the sound field forward to

improve the balance. Conversely, if the stereo image

feels like it’s in mono, or there’s not enough surround

sound, move it backward.

Multiplex/Mono

■ Multiplex

This setting determines which channel of a stereo multi-

plex source is output. Use it to select audio channels or

languages with multiplex sources, multilingual TV

broadcasts, and so on.

Input Channel

`Main:

The main channel is output.

`Sub:

Center Width

`0 to 3 to 7

With this setting, you can adjust the width of the sound

from the center speaker when using the Dolby Pro

Logic IIx Music listening mode. Normally, if you’re

using a center speaker, the center channel sound is out-

put by only the center speaker. (If you’re not using a

center speaker, the center channel sound will be distrib-

uted to the front left and right speakers to create a phan-

tom center). This setting controls the front left, right,

and center mix, allowing you to adjust the weight of the

center channel sound.

The sub channel is output.

`Main/Sub:

Both the main and sub channels are output.

■ Mono

This setting specifies the channel to be used for playing

any 2-channel digital source such as Dolby Digital, or

2-channel analog/PCM source in the Mono listening

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ PLIIz Height Gain

Theater-Dimensional

The Height Gain Control in Dolby Pro Logic IIz

enables the listener to select how much gain is applied

to the front high speakers. There are three settings,

“Low”, “Mid” and “High”, and the front high speakers

are accentuated in that order. While “Mid” is the default

listening setting, the listener may adjust the Height Gain

Control to their personal preference.

`Low:

Low PLIIz Height Gain becomes active.

`Mid:

Medium PLIIz Height Gain becomes active.

`High:

■ Listening Angle

`Wide:

Select if the listening angle is 40 degrees.

`Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the Theater-Dimen-

sional listening mode by specifying the angle of the

front left and right speakers relative to the listening

position. Ideally, the front left and right speakers should

be equidistant from the listening position and at an

angle close to one of the two available settings.

High PLIIz Height Gain becomes active.

Front left speaker

Front right speaker

20°/40°

Note

• If the “Front High” settings is set to “None” (➔ 44), this setting

cannot be selected.

■ Dolby EX

This setting determines how Dolby EX encoded signals

are handled. This setting is unavailable if no surround

back speakers are connected. This setting is effective

with Dolby Digital, Dolby Digital Plus and Dolby

TrueHD only.

LFE Level

■ Dolby Digital , DTS , Multich PCM, Dolby

TrueHD, DTS-HD Master Audio, DSD

`Auto:

If the source signal contains a Dolby EX flag, the

Dolby EX or THX Surround EX listening mode is

used.

`–QdB, –20dB, –10dB, or 0dB

With these settings, you can set the level of the LFE (Low

Frequency Effects) channel individually for each input

sources.

`Manual:

You can select any available listening mode.

If you find that low-frequency effects are too loud when

using one of these sources, change the setting to –20 dB or

–Q dB.

Note

• If the “Surr Back” setting is set to “None” (➔ 44), this setting

cannot be selected.

• If the “Front High” or “Front Wide” setting is enabled (➔ 44),

this setting is fixed at “Manual”.

Dolby Digital and Dolby Digital Plus sources.

DTS and DTS-HD High Resolution Audio sources.

DSD (Super Audio CD) sources.

DTS

Source Setup

■ Neo:6 Music

Items can be set individually for each input selector.

Center Image

`0 to 2 to 5

Preparation

The DTS Neo:6 Music listening mode creates 6-channel

surround sound from 2-channel stereo sources. With

this setting, you can specify by how much the front left

and right channel output is attenuated in order to create

the center channel.

Press the input selector buttons to select an input source.

Main menu

Source Setup

Audyssey

Setting a value “0” in the middle is set to hear a sound.

Sound is spread in left and right (the outside) so that the

set value is made big. Please adjust by liking.

When Audyssey MultEQ Room Correction and Speaker

Setup is complete, the “Equalizer” (➔ 46) will be set to

“Audyssey” and the “Dynamic EQ” will be set to “On”.

Audyssey DSX™

■ Dynamic EQ

■ Soundstage

`Off:

`–3dB to Reference to +3dB

With this setting, you can adjust the soundstage when using

Audyssey DSX™.

Audyssey Dynamic EQ off.

`On:

Audyssey Dynamic EQ on.

The Dynamic EQ indicator will light (➔ 9).

Note

• If the “Center” setting is set to “None”, or both “Front High”

and “Front Wide” settings are set to “None” (➔ 44), this setting

cannot be selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Dynamic Volume

With Audyssey Dynamic EQ , you can enjoy great

sound even when listening at low volume levels.

Audyssey Dynamic EQ solves the problem of deterio-

rating sound quality as volume is decreased by taking

into account human perception and room acoustics. It

does so by selecting the correct frequency response and

surround volume levels moment-by-moment so that the

content sounds the way it was created at any volume

level — not just at reference level.

`Off:

Audyssey Dynamic Volume off.

`Light:

Light Compression Mode becomes active.

`Medium:

Medium Compression Mode becomes active.

`Heavy:

Heavy Compression Mode becomes active. This set-

ting affects volume the most, causing all sounds to

be of equal loudness.

Note

• If Pure Audio or Direct listening mode is selected, this setting

cannot be selected.

Note

• Even if you have selected other than “Audyssey” in “Equalizer”

setting after performing Audyssey MultEQ Room Correction

and Speaker Setup, selecting “On” in the “Dynamic EQ” will

change the “Equalizer” setting to “Audyssey” (➔ 46).

• If you would like to use Audyssey Dynamic Volume, when

using THX listening modes, set “Loudness Plus” setting to

“Off” (➔ 46) and set “Preserve THX Settings” setting to “No”

(➔ 47).

• When “Dynamic Volume” is set to effective, “Equalizer” is set

to “Audyssey” (➔ 46) and “Dynamic EQ” is set to “On”.

When “Dynamic EQ” is set to “Off”, “Dynamic Volume”

becomes “Off” automatically.

■ Reference Level

Audyssey Dynamic EQ Reference Level Offset

`0dB:

It should be used when listening to movies.

`5dB:

Select this setting for content that has a very wide

dynamic range, such as classical music.

`10dB:

Select this setting for jazz or other music that has a

wider dynamic range. This setting should also be

selected for TV content as that is usually mixed at

10 dB below film reference.

• When “Dynamic Volume” is set to effective, the Dynamic Vol

indicator will light (➔ 9).

`15dB:

• If Pure Audio or Direct listening mode is selected, this setting

cannot be selected.

Select this setting for pop/rock music or other pro-

gram material that is mixed at very high listening

levels and has a compressed dynamic range.

Movies are mixed in rooms calibrated for film refer-

ence. To achieve the same reference level in a home the-

ater system each speaker level must be adjusted so that

–30 dBFS band-limited (500 Hz to 2000 Hz) pink noise

produces 75 dB sound pressure level at the listening

position. A home theater system automatically cali-

Audyssey MultEQ then removes the distortion caused by

room acoustics by capturing room acoustical problems

over the listening area in both the frequency and time

domain. The result is clear, well-balanced sound for every-

one. Enabling Audyssey MultEQ allows you to also use

Audyssey Dynamic EQ, which maintains the proper

octave-to-octave balance at any volume level.

Before using this function, connect and position all of

your speakers.

brated by Audyssey MultEQ will play at reference

level when the master volume control is set to the 0 dB

position. At that level you can hear the mix as the mix-

ers heard it.

About Audyssey Dynamic EQ

Audyssey Dynamic EQ solves the problem of deterio-

rating sound quality as volume is decreased by taking

into account human perception and room acoustics.

Dynamic EQ selects the correct frequency response and

surround levels moment-by-moment at any user-

selected volume setting. The result is bass response,

tonal balance, and surround impression that remain con-

stant despite changes in volume. Dynamic EQ combines

information from incoming source levels with actual

output sound levels in the room, a prerequisite for deliv-

ering a loudness correction solution.

Audyssey Dynamic EQ is referenced to the standard

film mix level. It makes adjustments to maintain the ref-

erence response and surround envelopment when the

volume is turned down from 0 dB. However, film refer-

ence level is not always used in music or other non-film

content. Audyssey Dynamic EQ Reference Level Offset

provides three offsets from the film level reference

(5 dB, 10 dB, and 15 dB) that can be selected when the

mix level of the content is not within the standard.

Note

Audyssey Dynamic EQ works in tandem with

Audyssey MultEQ to provide well-balanced sound for

every listener at any volume level.

• If “Dynamic EQ” setting is set to “Off”, this setting cannot be

selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

The custom name is edited using the character input

screen.

About Audyssey Dynamic Volume

Audyssey Dynamic Volume solves the problem of large

variations in volume level between television programs,

commercials, and between the soft and loud passages of

movies. Dynamic Volume looks at the preferred volume

setting by the user and then monitors how the volume of

program material is being perceived by listeners in real

time to decide whether an adjustment is needed. When-

ever necessary, Dynamic Volume makes the necessary

rapid or gradual adjustments to maintain the desired

playback volume level while optimizing the dynamic

■ Name

Use q/w/e/r to select a character, and then

press ENTER.

Repeat this step to enter up to 10 characters.

When you’ve finished, to store a name, be sure

to use q/w/e/r to select “OK”, and then press

ENTER. Otherwise it will not be saved.

range. Audyssey Dynamic EQ is integrated into

Name input area

Dynamic Volume so that as the playback volume is

adjusted automatically, the perceived bass response,

tonal balance, surround impression, and dialog clarity

remain the same whether watching movies, flipping

between television channels, or changing from stereo to

surround sound content.

4 - 4. Name Edit

Name

BD/DVD

–

{

}

Shift

Space

Back Space

IntelliVolume

+10

CLR

Shift

All Erase

■ IntelliVolume

`–12dB to 0dB to +12dB in 1 dB steps.

]

;

’

(

)

With IntelliVolume, you can set the input level for each

input selector individually. This is useful if one of your

source components is louder or quieter than the others.

[

Shift

Space

Back Space

+10

CLR

Shift

All Erase

Use e/r to set the level.

If a component is noticeably louder than the others, use e

to reduce its input level. If it’s noticeably quieter, use r to

increase its input level.

Shift :

Switches the displayed character.

Space:

A/V Sync

Enters a space character.

■ A/V Sync

`0ms to 250ms in 5 ms steps.

(Left)/ (Right):

Selected when the cursor is moved within the Name

input area.

When using your DVD player’s progressive scanning

function, you may find that the picture and sound are out

of sync. With the A/V Sync setting, you can correct this

by applying a delay to the audio signal.

To view the TV picture while setting the delay, press

ENTER.

Back Space :

“Back Space” moves the cursor backward one char-

acter space. In addition, “Back Space” deletes the

character to the left of the cursor.

OK:

To return to the previous screen, press RETURN.

Selects when the entry is complete.

Tip

If HDMI Lip Sync is enabled (➔ 54) and your TV or dis-

play supports HDMI Lip Sync, the displayed delay time

will be the summation of the A/V Sync delay time and the

HDMI Lip Sync delay time. The HDMI Lip Sync delay

time is displayed underneath in parentheses.

You can also be performed on the remote controller by

using +10.

Press CLR on the remote controller, you can delete all

characters in the input.

Note

To correct a character:

• A/V Sync is disabled when the Pure Audio listening mode is

selected, or when the Direct listening mode is used with an ana-

log input source.

• “A/V Sync” is not operable when the input selector is set to

“NET/USB”.

Use q/w/e/r to select “ ”(Left) or

“

”(Right), and then press ENTER.

Press ENTER several times to select the incor-

rect character (The cursor moves one letter

each time ENTER is pressed).

Name Edit

Use q/w/e/r to select the correct character,

You can enter a custom name for each individual input

selector (excluding TUNER) and radio preset for easy

identification. When entered, the custom name will appear

on the display.

and then press ENTER.

Download from Www.Somanuals.com. All Manuals Search And Download.

`Wide Zoom:

Note

• To name a radio preset, use TUNER to select AM or FM, and

then select the preset (➔ 33).

• “Name Edit” is not operable when the input selector is set to

“NET/USB”.

To restore a custom name to the default, erase the custom

name by entering an empty white space for each letter.

`Auto:

According to the input signals and monitor output

setting, the AV receiver automatically selects the

“4:3”, “Full”, “Zoom” or “Wide Zoom” mode. For

the monitor output setting (➔ 42).

Picture Adjust

Using “Picture Adjust”, you can adjust the picture qual-

ity and reduce any noise appearing on the screen.

To view the TV picture while setting, press ENTER. To

return to the previous screen, press RETURN.

*1*2

■ Picture Mode

`Through:

The following settings are set to the default values:

“Film Mode”, “Edge Enhancement”, “Noise

Reduction”, “Brightness”, “Contrast”, “Hue” and

“Saturation”

Note

• If you are using the analog RGB input, the following settings

have no effect: “Film Mode”, “Edge Enhancement”, and

“Noise Reduction”.

`Custom:

You can set the following settings as you like: “Film

Mode”, “Edge Enhancement”, “Noise Reduction”,

“Brightness”, “Contrast”, “Hue” and “Saturation”

`Cinema:

Selected when the picture source is movie film, etc.

`Game:

Select to use in connecting a game console.

With “Picture Mode”, you can change the following set-

tings to be suitable for the movie or game screen by one

operation; “Film Mode”, “Edge Enhancement”, “Noise

Reduction”, “Brightness”, “Contrast”, “Hue” or “Satu-

ration”.

• “Picture Adjust” is not operable when the input selector is set

to “NET/USB”.

■ Game Mode

`Off:

Game Mode off.

`On:

Game Mode on.

If video signal delay occurs during playback on a video

component (i.e. game console), select the corresponding

input source and set the “Game Mode” setting to “On”.

The delay will decrease but in return the picture quality

will become poor.

Note

*1*2

■ Wide Mode

• When the “Picture Mode” setting is set to other than “Custom”,

the following settings cannot be selected: “Film Mode”, “Edge

Enhancement”, “Noise Reduction”, “Brightness”, “Con-

trast”, “Hue” and “Saturation”.

This setting determines the aspect ratio.

Note

• When the “Game Mode” is set to “On”, this setting is fixed at

“Full”.

■ Film Mode

`Video:

`4:3:

Does not process in either “3:2” or “2:2”.

`Auto:

Adjusts to the picture source, automatically selecting

“Film Mode”.

`3:2:

Selected when the picture source is movie film, etc.

`Full:

`2:2:

Selected when the picture source is computer graph-

ics, animation, etc.

The AV receiver will adjust to the picture source, process-

ing in either “3:2” or “2:2” (Film Mode). It automatically

converts the source to the appropriate progressive signal

and reproduces the natural quality of the original picture.

When the “Film Mode” setting is set to “Auto”, the AV

receiver automatically detects the picture source and in

either “3:2” or “2:2”. However, there may be times when

you will get a better picture by setting “Film Mode” your-

self.

`Zoom:

Note

• If the “Game Mode” setting is set to “On” (➔ 51), this setting

is fixed at “Video”.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Edge Enhancement

`0 to +10

Listening Mode Preset

You can assign a default listening mode to each input

source that will be selected automatically when you select

each input source. For example, you can set the default lis-

tening mode to be used with Dolby Digital input signals.

You can select other listening modes during playback, but

the mode specified here will be resumed once the AV

receiver has been set to Standby.

With this setting you can adjust the sharpness of edges in

the picture. “0” is the softest. “+10” is the sharpest.

■ Noise Reduction

`Off:

Noise reduction off.

`Low:

Low noise reduction.

`Mid:

Main menu

Listening Mode Preset

Use q/w to select the input source that you want to

Medium noise reduction.

`High:

set, and then press ENTER.

The following menu appears.

High noise reduction.

With this setting, you can reduce noise appearing on the

screen.

5. Listening Mode Preset

1. BD/DVD

2. VCR/DVR

3. CBL/SAT

4. GAME

5. PC

Note

• If the “Game Mode” setting is set to “On” (➔ 51), this setting

6. AUX

is fixed at “Off”.

*1*2

■ Brightness

For “TUNER” input selector only “Analog” will be

available. For “NET/USB” input source only “Digi-

tal” will be available.

`–50 to 0 to +50

With this setting you can adjust the picture bright-

ness. “–50” is the darkest. “+50” is the brightest.

Note

*1*2

• If you connect an input component (such as UP-A1 series

Dock that seated iPod) to the UNIVERSAL PORT jack,

you can assign only listening modes for the analog sound

to “PORT” selector.

■ Contrast

`–50 to 0 to +50

With this setting you can adjust contrast. “–50” is the

least. “+50” is the greatest.

Use q/w to select the signal format that you want

to set, and then use e/r to select a listening mode.

Only listening modes that can be used with each

input signal format can be selected (➔ 36 to 40).

The “Last Valid” option means that the listening

mode selected last will be used.

*1*2

■ Hue

`–20 to 0 to +20

With this setting you can adjust the red/green bal-

ance. “–20” is the strongest green. “+20” is the

strongest red.

*1*2

■ Saturation

■ Analog/PCM

`–50 to 0 to +50

With this setting, you can specify the listening mode to

be used when an analog (CD, TV, LD, VHS, MD, turn-

table, radio, cassette, cable, satellite, etc.) or PCM digi-

tal (CD, DVD, etc.) audio signal is played.

With this setting you can adjust saturation. “–50” is

the weakest color. “+50” is the strongest color.

Tip

This procedure can also be performed on the remote controller

by using the Home menu (➔ 26).

Press CLR if you want to reset to the default value.

■ Mono/Multiplex Source

With this setting, you can specify the listening mode to

be used when a mono digital audio signal is played

(DVD, etc.).

■ 2ch Source

With this setting, the default listening mode for 2-chan-

nel (2/0) stereo sources in a digital format, such as

Dolby Digital or DTS.

■ Dolby D/Dolby D +/TrueHD

With this setting, you can specify the listening mode to

be used when a Dolby Digital or Dolby Digital Plus for-

mat digital audio signal is played (DVD, etc.). Specifies

the default listening mode for Dolby TrueHD sources,

such as Blu-ray or HD DVD (input via HDMI).

Download from Www.Somanuals.com. All Manuals Search And Download.

■ DTS/DTS-ES/DTS-HD

OSD Setup

With this setting, you can specify the listening mode to

be used when a DTS or DTS-HD High Resolution

Audio format digital audio signal is played (DVD, LD,

CD, etc.). Specifies the default listening mode for DTS-

HD Master Audio sources, such as Blu-ray or HD DVD

(input via HDMI).

■ On Screen Display

This preference determines whether operation details

are displayed onscreen when an AV receiver function is

adjusted.

`On:

Displayed.

`Off:

■ Other Multich Source

Specifies the default listening mode for multichannel

PCM sources from HDMI IN such as DVD-Audio, and

DSD multichannel sources such as Super Audio CD.

Not displayed.

Even when “On” is selected, operation details may not be

output if the input source is connected to an HDMI IN.

■ Language

Miscellaneous

`English, Deutsch, Français, Español, Italiano,

Nederlands, Svenska, 中文

Main menu

Miscellaneous

This setting determines the language used for the on-

screen setup menus.

Volume Setup

■ Volume Display

`Absolute:

Hardware Setup

Display range is “Min”, “0.5” through “99.5”,

Main menu

Hardware Setup

“Max”.

`Relative(THX):

Remote ID

Display range is “–QdB”, “–81.5dB” through

“+18.0dB”.

■ Remote ID

`1, 2, or 3

With this setting, you can choose how the volume level is

displayed.

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differenti-

ate the AV receiver from the other components, you can

change its remote ID from “1”, to “2” or “3”.

The absolute value 82 is equivalent to the relative value

0 dB.

■ Muting Level

`–QdB (fully muted), –50dB to –10dB in 10 dB steps.

This setting determines how much the output is muted

when the muting function is used (➔ 26).

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

■ Maximum Volume

Changing the Remote Controller’s ID

`Off, 50 to 99 (Absolute display)

`Off, –32dB to +17dB (Relative display)

With this setting, you can limit the maximum volume.

To disable this setting, select “Off”.

While holding down RECEIVER, press and hold

down SETUP until RECEIVER lights (about 3

seconds).

■ Power On Volume

`Last, Min, 1 to 99 or Max (Absolute display)

Use the number buttons to enter ID 1, 2, or 3.

RECEIVER flashes twice.

`Last, –QdB, –81dB to +18dB (Relative display)

With this preference, you can specify the volume set-

ting to be used each time the AV receiver is turned

on.

To use the same volume level that was used when the AV

receiver was turned off, select “Last”.

Tuner

For FM/AM tuning to work properly, you must specify the

FM/AM frequency step used in your area. Note that when

this setting is changed, all radio presets will be deleted.

The “Power On Volume” cannot be set higher than the

“Maximum Volume” setting.

■ FM/AM Frequency Step

`200kHz/10kHz:

Select if 200 kHz/10 kHz steps are used in your area.

`50kHz/9kHz:

■ Headphone Level

`–12dB to 0dB to +12dB

With this preference, you can specify the headphone vol-

ume relative to the main volume. This is useful if there’s a

volume difference between your speakers and your head-

phones.

Select if 50 kHz/9 kHz steps are used in your area.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ HDMI Control (RIHD)

`Off:

HDMI

■ Audio TV Out

`Off:

p disabled.

`On:

The audio is not output from the HDMI output.

`On:

The audio is output from the HDMI output.

This preference determines whether the incoming audio

signal is output from the HDMI OUT. You may want to

turn this preference on if your TV is connected to the

HDMI OUT and you want to listen to the audio from a

connected component through your TV’s speakers. Nor-

mally, this should be set to “Off”.

p enabled.

This function allows p-compatible components

connected via HDMI to be controlled with the AV receiver

(➔ 88 to 89).

Note

• When set to “On” and close the menu, the name of connected

p-compatible components and “RIHD On” are dis-

played on the AV receiver.

“Search…” → “(name)” → “RIHD On”

When the AV receiver cannot receive the name of the compo-

nent, it is displayed as “Player*” or “Recorder*”, etc (“*”

means the number of two or more component).

When set to “Off” and close the menu, “RIHD Off” are dis-

played on the AV receiver.

Note

• Listening mode cannot be changed when this setting is set to

“On” and the input source is not HDMI.

• If “On” is selected and the audio can be output from the TV, the

AV receiver will output no sound through its speakers. In this

case, “TV Sp On” appears on the display.

“Disconnect” → “RIHD Off”

• When an p-compatible component is connected to the

AV receiver via the HDMI cable, the name of the connected

component is displayed on the AV receiver display. For example,

while you are watching TV broadcasting, if you operate a

Blu-ray Disc/DVD player (being powered on) by the remote

control of the AV receiver, the name of the Blu-ray Disc/DVD

player is displayed on the AV receiver.

• Set to “Off” when a connected piece of equipment is not com-

patible or it is unclear whether the equipment is compatible or

not.

• When “TV Control” is set to “On ”, this setting is fixed to

“Auto”.

• With some TVs and input signals, no sound may be output even

when this setting is set to “On” (➔ 55).

• When the “Audio TV Out” setting is set to “On”, or “TV Con-

trol” is set to “On” (➔ 55) and you’re listening through your

TV’s speakers (➔ 18), if you turn up the AV receiver’s volume

control, the sound will be output by the AV receiver’s front left

and right speakers. To stop the AV receiver’s speakers producing

sound, change the settings, change your TV’s settings, or turn

down the AV receiver’s volume.

• If movement is unnatural when set to “On”, change the setting

to “Off”.

• Refer to the connected component’s instruction manual for

details.

■ Lip Sync

`Disable:

• When the source equipment is connected with the u connec-

tion, it may malfunction if “HDMI Control (RIHD)” is set to

“On”.

HDMI lip sync disabled.

`Enable:

HDMI lip sync enabled.

The AV receiver can be set to automatically correct any

delay between the video and the audio, based on the data

from the connected monitor.

■ Audio Return Channel

`Off:

Select “Off” if you don’t want to use audio return

channel (ARC) function.

`Auto:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

Audio return channel (ARC) function enables an HDMI

(Audio Return Channel) capable TV to send the audio

stream to the HDMI OUT of the AV receiver. To use this

function, you must select the TV/CD input selector and

your TV must support ARC function.

Note

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

• You can check the amount of delay being applied by the HDMI

Lip Sync function on the A/V Sync screen.

Note

• The “Audio Return Channel” setting can be set only when the

“HDMI Control (RIHD)” setting is set to “On”.

• This setting is set to “Auto” automatically when the “HDMI

Control (RIHD)” is set to “On” first time.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Power Control

Auto Power Down

`Off:

Power Control disabled.

`On:

Power Control enabled.

■ Auto Power Down

`Off:

Auto Power Down disabled.

`On:

To link the power functions of p-compatible com-

Auto Power Down enabled.

ponents connected via HDMI, select “On”.

This setting is set to “On” automatically when the

“HDMI Control (RIHD)” is set to “On” first time.

The AV receiver will automatically perform STANDBY

operation when “Auto Power Down” is set to “On”, with

no audio or video signal input, and if there is no operation

for 30 minutes.

“Auto Power Down” will display on the display and OSD

from 30 seconds before the Auto Power Down functions.

Note

• The “Power Control” setting can be set only when the “HDMI

Control (RIHD)” setting is set to “On”.

• HDMI power control only works with p-compatible

components that support it and may not work properly with

some components due to their settings or compatibility.

• When set to “On”, power consumption will increase.

• When set to “On”, regardless of whether the AV receiver is On

or in Standby, both audio and video stream from an HDMI input

will be output to the TV or other components via HDMI connec-

tion (HDMI pass through function). When the HDMI pass

through function activates in standby mode, HDMI THRU indi-

cator will light.

Note

• Depending on some sources, the Auto Power Down function

may activate during playback.

• The Auto Power Down function does not work when Zone 2 is

on.

Network

See “Network Settings” (➔ 65).

• The power consumption during standby mode will increase dur-

ing the HDMI pass through function; however if your TV sup-

ports CEC (Consumer Electronics Control), the power

consumption can be saved in the following cases:

1. The TV is in standby mode.

2. You are watching a TV program.

• Refer to the connected component’s instruction manual for

details.

Firmware Update

Note

• Perform the firmware update only when an announcement is

posted on the Onkyo web site. See the Onkyo web site for latest

information.

• It takes about 30 minutes to complete the firmware update.

■ TV Control

`Off:

■ Version

The current version of the firmware is displayed.

TV Control disabled.

`On:

■ Receiver

TV Control enabled.

`via NET:

Set to “On” when you want to control the AV receiver

from an p-compatible TV that is connected to

HDMI.

You can update the firmware via Internet. Check the

network connection before update.

`via USB:

You can update the firmware from a USB mass stor-

age device.

You can update the AV receiver’s firmware. Do not shut-

down the power of the AV receiver while update.

Note

• Do not assign the component connected with the HDMI input to

the TV/CDselector when you set “TV Control” setting to “On”.

Otherwise, appropriate CEC (Consumer Electronics Control)

operation is not guaranteed.

• Set to “Off” when the TV is not compatible or when it is unclear

whether the TV is compatible or not.

• The “TV Control” setting can be set only when the “HDMI

Control (RIHD)” (➔ 54) and “Power Control” (➔ 55) set-

tings are both set to “On”.

■ Universal Port

`via NET:

You can update the firmware via Internet. Check the

network connection before update.

`via USB:

You can update the firmware from a USB mass stor-

age device.

• Refer to the connected component’s instruction manual for

details.

You can update the Onkyo dock’s firmware. Do not shut-

down the power of the AV receiver while update.

After changing the settings of the “HDMI Control

(RIHD)”, “Audio Return Channel”, “Power Control”,

or “TV Control”, turn off the power to all connected

pieces of equipment and then turn them on again. Refer

to the user’s manuals for all connected pieces of equip-

ment.

Note

• This update shall not be performed when no dock is connected

to UNIVERSAL PORT jack.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lock Setup

Using the Audio Settings

With this preference, you can protect your settings by

locking the setup menus.

You can change various audio settings from the Home

menu (➔ 26).

Main menu

Lock Setup

Press RECEIVER followed by HOME.

■ Setup

`Locked:

Setup menus locked.

`Unlocked:

Setup menus not locked.

Use q/w to select “Audio”, and then use q/w/e/r

to make the desired selection.

Note

• These settings are disabled when:

– a pair of headphones is connected, or

– the “Audio TV Out” setting is set to “On” (➔ 54) and an

input selector other than HDMI is selected.

When the setup menus are locked, you cannot change any

setting.

Tone Control Settings

You can adjust the bass and treble for the front speakers,

except when the Direct, Pure Audio or THX listening

mode is selected.

■ Bass

`–10dB to 0dB to +10dB in 2 dB steps.

You can boost or cut low-frequency sounds output

by the front speakers.

■ Treble

`–10dB to 0dB to +10dB in 2 dB steps.

You can boost or cut high-frequency sounds output

by the front speakers.

Operating on the AV receiver

Press TONE on the AV receiver repeatedly to

select either “Bass” or “Treble”.

Use TONE LEVEL +/– on the AV receiver to

adjust.

Note

• This setting is not available when the multichannel Analog input

is selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Levels

Music Optimizer

You can adjust the volume of each speaker while listening

to an input source.

These temporary adjustments are cancelled when the AV

receiver is set to Standby. To save the setting you made

here, go to “Level Calibration” (➔ 45) before setting the

AV receiver to Standby.

The Music Optimizer function enhances the sound quality

of compressed music files. Use it with music files that use

“lossy” compression, such as MP3.

■ Music Optimizer

`Off:

Music Optimizer off.

■ Subwoofer Level

`On:

`–15.0dB to 0.0dB to +12.0dB in 1 dB steps.

Music Optimizer on. The M.Opt indicator will light

(➔ 9).

■ Center Level

`–12.0dB to 0.0dB to +12.0dB in 1 dB steps.

Note

• The Music Optimizer function only works with PCM digital

audio input signals with a sampling rate below 48 kHz and ana-

log audio input signals. The Music Optimizer is disabled when

the Direct or Pure Audio listening mode is selected.

Note

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to “No” or “None” in the

“Speaker Configuration” (➔ 44 ) cannot be adjusted.

• The setting is stored individually for each input selector.

Audyssey Settings

Re-EQ

With the Re-EQ function, you can compensate a

soundtrack whose high-frequency content is too harsh,

making it more suitable for home theater viewing.

■ Dynamic EQ

See “Dynamic EQ” of “Source Setup” (➔ 48).

■ Dynamic Volume

See “Dynamic Volume” of “Source Setup” (➔ 49).

■ Re-EQ

`Off:

Re-EQ Function off.

`On:

Late Night

With the Late Night function, you can reduce the dynamic

range of Dolby Digital material so that you can still hear

quiet parts even when listening at low volume levels—

ideal for watching movies late at night when you don’t

want to disturb anyone.

Re-EQ Function on.

This function can be used with the following listening

modes: Dolby Digital, Dolby Digital Plus,

Dolby TrueHD, Multichannel, DTS, DTS-HD High Reso-

lution Audio, DTS-HD Master Audio, DTS Express,

DSD, Dolby EX, Dolby Pro Logic IIz Height, Dolby

PLIIx Movie, Neo:6 Cinema and 5.1-channel source +

Neo:6.

■ Late Night

For Dolby Digital and Dolby Digital Plus sources, the

options are:

`Off:

■ Re-EQ(THX)

Late Night function off.

`Off:

`Low:

Re-EQ (THX) Function off.

Small reduction in dynamic range.

`High:

`On:

Re-EQ (THX) Function on.

This function can be used with the following listening

modes: THX Cinema, THX Surround EX, and

THX Select2 Cinema.

Large reduction in dynamic range.

For Dolby TrueHD sources, the options are:

`Auto:

The Late Night function is set to “On” or “Off”

Note

automatically.

`Off:

Late Night function off.

`On:

• Settings for the Re-EQ function are kept in each listening mode.

However, in THX listening mode, when the AV receiver is

turned off, it will return to “On”.

Late Night function on.

Note

• The effect of the Late Night function depends on the material

that you are playing and the intention of the original sound

designer, and with some material there will be little or no effect

when you select the different options.

• The Late Night function can be used only when the input source

is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “Off” when the AV receiver is

set to Standby. For Dolby TrueHD sources, it will be set to

“Auto”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio Selector

Setting the Incoming Digital Signal (Fixed

Mode)

You can set priorities of audio output when there are both

digital and analog inputs.

By pressing ENTER while selecting “HDMI”, “COAX”,

“OPT” in the “Audio Selector”, you can specify the input

signal in the Fixed Mode. Pressing ENTER again allows

you to return to the “Audio Selector” setting.

Normally, the AV receiver detects the signal format auto-

matically. However, if you experience either of the follow-

ing issues when playing PCM or DTS material, you can

manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut

off, try setting the format to PCM.

■ Audio Selector

`ARC:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

With this selection the TV’s audio can be automati-

cally selected as a priority among other assignments.

`HDMI:

This can be selected when HDMI IN has been

assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or OPTI-

CAL IN) have been assigned, HDMI input is auto-

matically selected as a priority.

• If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

`Auto:

The format is detected automatically. If no digital

input signal is present, the corresponding analog

input is used instead.

`COAX:

This can be selected when COAXIAL IN has been

assigned as an input source. If both coaxial and

HDMI inputs have been assigned, coaxial input is

automatically selected as a priority.

`OPT:

This can be selected when OPTICAL IN has been

assigned as an input source. If both optical and

HDMI inputs have been assigned, optical input is

automatically selected as a priority.

`Multich:

`PCM:

Only 2-channel PCM format input signals will be

heard. If the input signal is not PCM, the PCM indi-

cator will flash and noise may also be produced.

`DTS:

Only DTS (but not DTS-HD) format input signals

will be heard. If the input signal is not DTS, the DTS

indicator will flash and there will be no sound.

Note

The AV receiver always outputs analog signals from

multichannel analog input.

• The setting is stored individually for each input selector.

• The setting will be reset to “Auto” when you change the setting

in the “Audio Selector” (➔ 58).

`Analog:

The AV receiver always outputs analog signals.

Note

• The setting is stored individually for each input selector.

• This setting can be made only for the input source that is

assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.

• To select the digital audio input, see “Digital Audio Input” for

more detail (➔ 43).

• “Multich” can be selected only when the selector is set to “BD/

DVD”.

You can select “ARC” if you select the TV/CD input selector.

But you cannot select it if you’ve selected “Off” in the “Audio

Return Channel” setting (➔ 54).

Download from Www.Somanuals.com. All Manuals Search And Download.

NET/USB

About NET

Connecting the AV Receiver

The AV receiver is network-ready, which means you can

hook it up to your home network with a standard Ethernet

cable and enjoy the music files stored on your computer or

media server. If your network is connected to the Internet,

you can also enjoy Internet radio.

To connect the AV receiver to your home network, plug

one end of a shielded CAT5 Ethernet cable into the AV

receiver’s ETHERNET port, and plug the other end into a

LAN port on your router or switch.

The following diagram shows how you can connect the

AV receiver to your home network. In this example, it’s

connected to a LAN port on a router, which has a 4-port

100Base-TX switch built-in.

Network Requirements

■ Ethernet Network

For best results, a 100Base-TX switched Ethernet network

is recommended. Although it’s possible to play music on a

computer that’s connected to the network wirelessly, play-

back may be unreliable, so wired connections are recom-

mended.

■ Ethernet Router

A router manages the network, routing data and supplying

IP addresses. Your router must support the following:

• NAT (Network Address Translation). NAT allows sev-

eral networked computers to access the Internet simulta-

neously via a single Internet connection. The AV

receiver needs Internet access for Internet radio.

• DHCP (Dynamic Host Configuration Protocol). DHCP

supplies IP addresses to network devices, allowing them

to configure themselves automatically.

• A router with a 100Base-TX switch built-in is recom-

mended.

Some routers have a modem built-in, and some ISPs

require you to use specific routers. Please consult your ISP

or computer dealer if you’re unsure.

Internet radio

Modem

WAN port

Router

LAN port

■ CAT5 Ethernet cable

Use a shielded CAT5 Ethernet cable (straight-type) to con-

nect the AV receiver to your home network.

LAN/Ethernet port

■ Internet Access (for Internet radio)

To receive Internet radio, your Ethernet network must

have Internet access. A narrowband Internet connection

(e.g., 56K modem, ISDN) will not provide satisfactory

results, so a broadband connection is strongly recom-

mended (e.g., cable modem, xDSL modem, etc). Please

consult your ISP or computer dealer if you’re unsure.

Computer or media server

Note

• To receive Internet radio with the A V r eceiver, your broadband

Internet connection must be working and able to access the Web.

Consult your ISP if you have any problems with your Internet

connection.

• The AV receiver uses DHCP to configure its network settings

automatically. If you want to configure these settings manually,

see “Network Settings” (➔ 65).

• The AV receiver does not support PPPoE settings, so if you have

a PPPoE-type Internet connection, you must use a PPPoE-com-

patible router.

• Depending on your ISP, you may need to specify a proxy server

to use Internet radio. If your computer is configured to use a

proxy server, use the same settings for the AV receiver (➔ 65).

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to Internet Radio

Note

• When the NETWORK indicator flashes, confirm that the

Ethernet cable is firmly connected to the AV receiver.

• Services available may vary depending on the region. See

the separate instructions for more information.

To receive Internet radio, you must connect the AV

receiver to a network with Internet access (➔ 59).

You can select Internet radio stations by connecting to the

AV receiver from your computer and selecting stations in

your Web browser. Preset up to 40 Internet radio stations.

Internet radio URLs in the following formats are sup-

ported: PLS, M3U, and podcast (RSS). However, depend-

ing on the type of data or audio format used by the Internet

radio station, you may not be able to listen to some sta-

tions.

MENU:

When menu operations are enabled, “MENU” appears.

Press MENU to display the menu.

TOP MENU:

Press TOP MENU to go to the top menu of the Internet

Radio services.

Use q/w to select “1. vTuner Internet Radio”, and

then press ENTER.

Note

Use q/w to select a program, and then press

ENTER.

• If you’re using a narrowband Internet connection (e.g., 56K

modem or ISDN), depending on the station, Internet radio may

not work satisfactorily. For best results, use a broadband connec-

tion (e.g., cable modem, xDSL modem, etc).

Playback starts and the following screen appears.

All Stations

Listening to vTuner Internet Radio

- - -

1. fm indie 104

The internet’s best source for i

This unit includes the full vTuner Internet Radio Service

at no additional charge. Once you have connected your

unit to the Internet you can select vTuner Internet Radio to

search for and play Internet radio stations and podcasts at

any time. To enhance your Internet radio experience, the

http://onkyo.vtuner.com/ portal is available to you as an

easy way to browse to find stations, set up/organize your

favorites, add your own stations, get help, etc. After the

first time you try Internet radio/vTuner on your unit you

can use the MAC Address of your unit to create a member

onkyo.vtuner.com/ portal. To verify your MAC Address,

please see “Network Settings” (➔ 65).

0:00:00

WMA 128kbps 16bit/44.1kHz

Go to Menu

Press MENU to allow selection from the following

menu items.

`Stations like this:

Stations like the one currently being played

back are displayed.

Tip

• If you press DISPLAY, you can toggle between the play-

back screen and the list screen.

DISPLAY

NET/USB

Listening to Other Internet Radio

To listen to other internet radio stations, insert the follow-

ing step after step 1 in the “Listening to vTuner Internet

Radio”.

On your computer, start your Web browser and

enter the AV receiver’s IP address in the browser’s

Internet address (URL) field.

The browser connects to the AV receiver and dis-

plays the same screen as the AV receiver.

TOP MENU

qwer

Select the Internet radio station with your

browser.

ENTER

Note

Press NET/USB repeatedly to select the “Internet

Radio” screen.

• The AV receiver’s IP address is shown on the “Network”

screen (➔ 65).

• If you’re using DHCP, your router may not always allocate

the same IP address to the AV receiver, so if you find that

you can’t connect to the AV receiver, recheck the AV

receiver’s IP address on the “Network” screen.

Internet Radio

1. vTuner Internet Radio

2. Pandora Internet Radio

3. Rhapsody

4. SIRIUS Internet Radio

5. Slacker Internet Radio

6. Mediafly Internet Radio

7. Napster Internet Radio

8. ---

9. ---

10. ---

Go to Menu

The NETWORK indicator lights (➔ 9).

Download from Www.Somanuals.com. All Manuals Search And Download.

Start your computer or media server.

Registering Presets

Once you’ve added a station to the list, simply select it on

the Internet Radio screen, and then press ENTER to start

playback.

Press NET/USB to select the “Server” screen.

Server

Server1

Server2

Server3

Server4

Server5

Server6

Server7

Server8

Server9

Server10

From the search results you can preset the stations and songs

but cannot listen to them directly.

■ Items on the Internet Radio Top Menu

`Create new preset:

Add a favorite station or Internet Radio to the pre-

sets.

1 / 10

`Rename this preset:

You can rename the preset.

`Delete this preset:

The NETWORK indicator lights (➔ 9).

Note

• When the NETWORK indicator flashes, confirm the net-

work connection.

This will delete the preset.

■ Station and Song Presets

You can add the currently playing song or station to the

presets.

1. Press MENU with the station selected or while a song

is playing.

• To update the screen, press RETURN.

Use q/w to select the “Server1”, and then press

ENTER.

A list of items on the server appears.

Server1

2. Use q/w to select “Add this station to preset”, and

Recently Added

Artists

Album

Songs

press ENTER.

Playing Music Files on a Server

Genre

Year

Rating

This section explains how to play music files on a com-

puter or media server through the AV receiver. See “Sup-

ported Audio File Formats” to “About DLNA” for details

on supported music servers and music file formats.

For Windows Media Player 11, see “Windows Media

Player 11 Setup” (➔ 62).

1 / 8

You can search for music by Artist, Album, or Track.

Note

• The search function does not work with media servers

which do not support this function.

• Depending on the sharing settings in the media server, the

AV receiver may not able to access the content. Refer to

the instruction manual of the media server.

DISPLAY

NET/USB

Use q/w to select an item, and then press ENTER.

A list of music files appears.

All Music

Song 1

Song 2

Song 3

ENTER

My favorite song 1

My favorite song 2

My favorite song 3

My favorite song 4

My favorite song 5

My favorite song 6

My favorite song 7

1 / 10

q/w/e/r

RETURN

1, 3, 2, 5,

4, 7, 6

REPEAT

RANDOM

Download from Www.Somanuals.com. All Manuals Search And Download.

Windows Media Player 11 Setup

Use q/w to select a music file, and press ENTER or

1 to start playback.

This section explains how to configure Windows Media

Player 11 so that the AV receiver can play the music files

stored on your computer.

Playback starts and the following screen appears.

My favorite song 1

4 / 10

Start Windows Media Player 11.

My favorite song 1

Artist name

My favorite album

0:00:00

On the Library menu, select Media Sharing.

The Media Sharing dialog box appears.

MP3 128kbps 44.1kHz

ALL

Select the Share my media check box, and then

click OK.

• To return to the previous menu during playback,

press RETURN.

Select the AV receiver in the list, and then click

Allow.

• To stop playback, press 2.

Click OK to close the dialog box.

This completes the Windows Media Player 11 con-

figuration.

You can now play the music files in your Windows

Media Player 11 library through the AV receiver

(➔ 61).

• To select the next song, press 6. To select the

beginning of the current song, press 7. To select

the previous song, press 7 twice.

• To pause playback, press 3. To fast forward the

current song, press 4. To fast reverse the current

song, press 5.

Note

Tip

• Windows Media Player 11 can be downloaded for free from the

Microsoft Web site.

• If you press DISPLAY, you can toggle between the play-

back screen and the list screen.

Note

Supported Audio File Formats

• For some sort of media server, Fast Forward/Fast Reverse/

Pause operations do not work.

For server playback, the AV receiver supports the follow-

ing music file formats: MP3, WMA, WAV, FLAC, Ogg

Vorbis, AAC and LPCM. Not all servers support all for-

mats.

Random Playback

The Random function can only be set while the PLAY

screen is displayed.

■ MP3

To play songs in random order, during playback (or while

playback is paused or stopped), press RANDOM. All of

the songs in the current folder will be played in random

order. When all of the songs in the folder have been played

once, they’ll all be played again in a different random

order. To cancel random playback, press RANDOM

again.

Random playback supports up to 20000 songs per folder.

If a folder contains more than this, songs over 20000 are

not included in random playback.

Repeat Playback

The Repeat function can only be set while the PLAY

screen is displayed.

To play songs repeatedly, during playback (or while play-

back is paused or stopped), press REPEAT repeatedly to

select: Repeat1, Repeat Folder, Repeat All, or Off.

In Repeat1 mode, the current song is played repeatedly.

In Repeat Folder mode, all of the songs in the current

folder are played repeatedly.

• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3 for-

mat with a sampling rate of 8 kHz, 11.025 kHz, 12 kHz,

16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz

and a bit-rate of between 8 kbps and 320 kbps. Incom-

patible files cannot be played.

• Number of channels: 2

• Variable bit-rate (VBR) MP3 files are supported. (Play-

ing times may not display correctly.)

• MP3 files must have a “.mp3” or “.MP3” filename

extension.

■ WMA

WMA stands for Windows Media Audio and is an audio

compression technology developed by Microsoft Corpora-

tion. Audio can be encoded in WMA format by using

Windows Media Player.

• WMA files must have the copyright option turned off.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and

bitrates of between 5 kbps and 320 kbps, and WMA

DRM are supported. Incompatible files cannot be

played.

• Number of channels: 2

• Variable bit-rates (VBR) are supported. (Playing times

may display incorrectly with VBR.)

In Repeat All mode, all of the songs on the current server

are played repeatedly.

To cancel repeat playback, press REPEAT repeatedly to

select Off.

Note

• If the message “No Item.” appears, this means that no informa-

tion can be retrieved from the server. In this case, check your

server, network, and AV receiver connections.

• WMA Pro/Voice formats are not supported.

• WMA files must have a “.wma” or “.WMA” filename

extension.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ WMA Lossless

■ LPCM (Linear PCM)

• Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

and bitrates of between 5 kbps and 320 kbps are sup-

ported. Incompatible files cannot be played.

• Quantization bit: 16 bit, 24 bit

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, and 96 kHz are supported.

• Quantization bit: 8 bit, 16 bit, 24 bit

• Number of channels: 2

• Variable bit-rates (VBR) are supported. (Playing times

may display incorrectly with VBR.)

• WMA files must have a “.wma” or “.WMA” filename

extension.

Server Requirements

The AV receiver can play digital music files stored on a

computer or media server and supports the following tech-

nologies:

■ WAV

• Windows Media Player 11

• Windows Media Connect 2.0

• DLNA-certified media server

If the operating system of your computer is Windows

Vista, Windows Media Player 11 is already installed.

Windows Media Player 11 for Windows XP can be down-

loaded for free from the Microsoft Web site.

• The computer or media server must be on the same net-

work as the AV receiver.

WAV files contain uncompressed PCM digital audio.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, and 96 kHz are supported. Incompatible files

cannot be played.

• Quantization bit: 8 bit, 16 bit, 24 bit

• Number of channels: 2

• WAV files must have a “.wav” or “.WAV” filename

extension.

• Each folder may contain up to 20000 music files, and

folders may be nested up to 16 levels deep.

■ AAC

AAC stands for MPEG-2/MPEG-4 Audio.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, 96 kHz and bitrates of between 8 and

320 kbps, are supported. Incompatible files cannot be

played.

Note

• For some sort of media server, the AV receiver may not able to

recognize it, or may not able to play stored music files.

Minimum system requirements for Windows Media

Player 11 for Windows XP

• Number of channels: 2

Operating system

• Variable bit-rate (VBR) files are supported. (Playing

times may not display correctly.)

• AAC files must have a “.aac”, “.m4a”, “.mp4”, “.3gp”,

“.3g2”, “.AAC”, “.M4A”, “.MP4”, “.3GP” or “.3G2”

filename extension.

Windows XP Home Edition (SP2), Windows XP Profes-

sional (SP2), Windows XP Tablet PC Edition (SP2),

Update Rollup 2 for Windows XP Media Center Edition

2005 (KB900325), October 2006 Update Rollup for

Windows XP Media Center Edition (KB925766)

■ FLAC

Processor:

233 MHz Intel Pentium II, Advanced

Micro Devices (AMD), etc.

FLAC is a file format for lossless audio data compression.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, and 96 kHz are supported. Incompatible files

cannot be played.

• Quantization bit: 8 bit, 16 bit, 24 bit

• Number of channels: 2

• Variable bit-rates (VBR) are supported. (Playing times

may display incorrectly with VBR.)

• FLAC files must have a “.flac” or “.FLAC” filename

extension.

Memory:

Hard disk:

Drive:

64 MB

200 MB of free space

CD or DVD drive

28.8 kbps

Modem:

Sound card:

Monitor:

Video card:

Software:

16-bit sound card

Super VGA (800 x 600)

64 MB VRAM, DirectX 9.0b

Microsoft ActiveSync (only when

using a Windows Mobile-based Pocket

PC or smartphone)

Note

• Not all servers support all formats.

Web browser: Microsoft Internet Explorer 6 or

Netscape 7.1

■ Ogg Vorbis

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and

bitrates of between 48 kbps and 500 kbps are supported.

Incompatible files cannot be played.

• Number of channels: 2

• Variable bit-rates (VBR) are supported. (Playing times

may display incorrectly with VBR.)

About DLNA

The Digital Living Network Alliance is an international,

cross-industry collaboration. Members of DLNA develop

a concept of wired and wireless interoperable networks

where digital content such as photos, music, and videos

can be shared through consumer electronics, personal

computers, and mobile devices in and beyond the home.

The AV receiver certificate the DLNA Interoperability

Guidelines version 1.5.

• Ogg Vorbis files must have a “.ogg” or “.OGG” filename

extension.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Remote Playback

Remote Playback from Media Server/

Personal Computer

Start Windows Media Player 12.

Before remote playback, setup on Windows Media

Player 12 is required.

Remote Playback means you can play the music files

stored on the DLNA-certified device such as media server

with this product by operating the controller device in the

home network.

On the product, press NET/USB to select the

“Server” screen.

A list of media server appears.

Server Requirements

Tip

• Windows Media Player 12

• The NETWORK indicator on the product’s display lights

up. When it flashes, confirm the network connection.

• DLNA-certified (the DLNA Interoperability Guidelines

version 1.5) media server or controller device

Setting varies depending on the device. Refer to your

device’s instruction manual for details.

If the operating system of your personal computer is Win-

dows 7, Windows Media Player 12 is already installed.

For more information, see the Microsoft Web site.

Note

• While the music files on another media server are being

played, remote playback cannot be used. Stop playback on

another media server.

On Windows Media Player 12, right-click on

music file.

Right-click menu appears. For selecting another

media server, select media server from “Other

Libraries” menu on Windows Media Player 12.

Supported Music File Formats

See “Supported Audio File Formats” (➔ 62).

Note

Select the product from right-click menu.

• For remote playback, this product does not support the following

music file formats: FLAC and Ogg Vorbis.

“Play to” window appears and playback on the prod-

uct starts. Operations during remote playback can be

made from “Play to” window of Windows 7 on your

personal computer. During remote playback, opera-

tions (such as Playback, Pause, Fast Forward, Fast

Rewind, Previous, Next, Repeat, Random) cannot be

made on the product.

Windows Media Player 12 Setup

This section explains how to configure Windows Media

Player 12 so that the product can play the music files

stored on your personal computer.

Remote Playback

Start Windows Media Player 12.

My favorite song 1

Artist name

On the “Stream” menu, select “Turn on media

streaming”.

A dialog box appears.

My favorite album

1:00:00

MP3 128kbps 44.1kHz

Move your cursor and click on “Turn on media

streaming”.

A list of media server appears. Wording may vary

slightly depending on the network location.

Tip

• To stop playback and return to the previous menu during

remote playback, press RETURN on the product or

remote controller. To stop playback during remote play-

back, press Stop [2] on the remote controller.

Select the product in the list, and then click

“Allowed”.

Adjusting the Volume.

Click “OK” to close the dialog box.

This completes the Windows Media Player 12 con-

figuration.

You can now play the music files in your Windows

Media Player 12 library through the product.

You can adjust the volume of your AV receiver by

adjusting the volume bar in the “Remote playback”

window. The default maximum volume for the AV

receiver is 82 (0dB). If you wish to change this, enter

the maximum volume value from the Web Setup in

your browser.

The volume value of the remote window and the vol-

ume value of the AV receiver may not always match.

Adjustments you make to the volume in the AV

receiver will not be reflected in the “Remote play-

back” window.

Windows and the Windows logo are trademarks of the

Microsoft group of companies.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use q/w to select the setting, and use e/r to set

them.

Network Settings

To enter an IP address, select the setting, and then

press ENTER. The arrow can then be used to enter

numbers. Press ENTER again to set the number.

The settings are explained below.

Note

• When modifying network settings, after modifying it is neces-

sary to execute “Save”.

This section explains how to configure the AV receiver’s

network settings manually.

When you’ve finished, press RETURN.

The save confirmation screen appears.

If your router’s DHCP server is enabled, you don’t need to

change any of these settings, as the AV receiver is set use

DHCP to configure itself automatically by default (i.e.,

DHCP is set to Enable). If, however, your router’s DHCP

server is disabled, for example, you’re using static IP

addresses, you’ll need to configure these settings yourself,

in which case, a knowledge of Ethernet networking is

essential.

7-5. Network

Save

Cancel

Use q/w to select “Save”, and then press ENTER.

When modifying network settings, after modifying it

is necessary to execute “Save”.

Press SETUP.

The setup menu closes.

What’s DHCP?

DHCP (Dynamic Host Configuration Protocol) is used by

routers, computers, the AV receiver, and other devices to

automatically configure themselves on a network.

What’s DNS?

Note

• This procedure can also be performed on the AV receiver by

using SETUP, arrow buttons, and ENTER.

The DNS (Domain Name System) translates domain

names into IP addresses. For example, when you enter a

domain name such as www.onkyousa.com in your Web

browser, before accessing the site, your browser uses DNS

to translate this into an IP address, in this case

63.148.251.142.

■ Mac Address

This is the AV receiver’s MAC (Media Access Control)

address. This address cannot be changed.

■ DHCP

This setting determines whether or not the AV receiver

uses DHCP to automatically configure its IP Address,

Subnet Mask, Gateway, and DNS Server settings.

`Enable:

DHCP enabled.

`Disable:

Press RECEIVER followed by SETUP.

The main menu appears onscreen.

Tip

• If the main menu doesn’t appear, make sure the appropri-

ate external input is selected on your TV.

DHCP disabled.

Use q/w to select “Hardware Setup”, and then

If you select “Disable”, you must configure the “IP

Address”, “Subnet Mask”, “Gateway”, and “DNS

Server” settings yourself.

press ENTER.

The “Hardware Setup” menu appears.

7. Hardware Setup

■ IP Address

1. Remote ID

2. Tuner

3. HDMI

4. Auto Power Down

5. Network

6. Firmware Update

If you set the “DHCP” setting to “Disable”, you must

specify an IP address. Enter a static IP address provided

by your ISP.

The IP address must be within the following ranges.

`Class A:

10.0.0.0 to 10.255.255.255

`Class B:

Use q/w to select “Network”, and then press

ENTER.

The “Network” screen appears.

172.16.0.0 to 172.31.255.255

7-5. Network

`Class C:

192.168.0.0 to 192.168.255.255

Most routers use Class C IP addresses.

MAC Address

DHCP

IP Address

Subnet Mask

Gateway

xx : xx : xx − yy : yy : yy

Disable

aaa.bbb.ccc.ddd

DNS Server

■ Subnet Mask

If you set the “DHCP” setting to “Disable”, you must

specify a subnet mask address.

Proxy URL

Proxy Port

http://www.proxy.xxx.com

8080

Enter the subnet mask address provided by your ISP (typi-

cally: 255.255.255.0).

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Gateway

About USB

If you set the “DHCP” setting to “Disable”, you must

specify a gateway address.

Enter the gateway address provided by your ISP.

USB can be used to play music files stored on USB mass

storage devices (e.g., USB flash drives and MP3 players),

which can be plugged into the AV receiver’s USB port.

■ DNS Server

If you set the “DHCP” setting to “Disable”, you must

specify a DNS server.

Supported Audio File Formats

For USB mass storage device playback, the AV receiver

supports music file formats.

See “Supported Audio File Formats” (➔ 62).

Enter the DNS server addresses provided by your ISP.

■ Proxy URL

To use a Web proxy, enter its URL here.

USB Mass Storage Device Requirements

■ Proxy Port

If you’re using a Web proxy, enter a proxy port number

here.

• The AV receiver supports USB devices that support the

USB mass storage device class.

• Playback may not be possible with some USB devices

even if they conform to the USB mass storage device

class.

• USB devices formatted with the FAT16 or FAT32 file

system are supported.

■ Control

This setting enables or disables control over the network.

`Enable:

Control over the network enabled.

`Disable:

• If the storage device has been partitioned, each section

will be treated as an independent device.

• Each folder may contain up to 20000 music files and

folders, and folders may be nested up to 16 levels deep.

• USB hubs and USB devices with hub functions are not

supported.

Control over the network disabled.

Note

• When set to “Enable”, power consumption on standby mode

slightly increases.

■ Port Number

This is the network port used for control over the network.

Playing Music Files on a USB Device

Note

This section explains how to play music files on a USB

mass storage device.

• Set the port number between from “49152” to “65535”.

DISPLAY

NET/USB

ENTER

q/w/e/r

RETURN

1, 3, 2, 5,

4, 7, 6

REPEAT

RANDOM

Download from Www.Somanuals.com. All Manuals Search And Download.

Random Playback

The Random function can only be set while the PLAY

screen is displayed.

To play songs in random order, while the list of songs is

displayed, press RANDOM. All of the songs in the cur-

rent folder will be played in random order. When all of the

songs in the folder have been played once, they’ll all be

played again in a different random order. To cancel ran-

dom playback, press RANDOM again.

Plug your USB mass storage device into the AV

receiver’s USB port.

Press NET/USB repeatedly to select the “USB”

input.

USB

USB Storage

Random playback supports up to 20,000 songs per folder.

If a folder contains more than this, songs over 20,000 are

not included in random playback.

1 / 1

Repeat Playback

The USB indicator lights (➔ 9) if the AV receiver is

able to read the USB mass storage device. The USB

indicator flashes if the AV receiver cannot read the

USB mass storage device.

The Repeat function can only be set while the PLAY

screen is displayed.

To play songs repeatedly, during playback (or while play-

back is paused or stopped), press REPEAT repeatedly to

select: Repeat1, Repeat Folder, Repeat All, or Off.

In Repeat1 mode, the current song is played repeatedly.

In Repeat Folder mode, all of the songs in the current

folder are played repeatedly.

In Repeat All mode, all of the songs on the USB mass

storage device (in the same partition) are played repeat-

edly.

Use q/w to select a USB mass storage device, and

then press ENTER.

A list of the device’s contents appears.

USB Storage

Folder1

Folder2

01_Song_Track1

02_Song_Track2

03_Song_Track3

04_Song_Track4

05_Song_Track5

06_Song_Track6

07_Song_Track7

08_Song_Track8

2 / 5

To cancel repeat playback, press REPEAT repeatedly to

select Off.

Note

• If you connect a USB hard disk drive to the AV receiver’s USB

port, we recommend that you use its AC adapter to power it.

• Do not connect the AV receiver’s USB port to a USB port on

your computer. Music on your computer cannot be played

through the AV receiver in this way.

• The AV receiver supports USB MP3 players that support the

USB Mass Storage Class standard, which allows USB storage

devices to be connected to computers without the need for spe-

cial drivers or software. Note that not all USB MP3 players sup-

port the USB Mass Storage Class standard. Refer your USB

MP3 player’s instruction manual for details.

• Protected WMA music files on an MP3 player cannot be played.

• Onkyo accepts no responsibility whatsoever for the loss or dam-

age to data stored on a USB mass storage device when that

device is used with the AV receiver. We recommend that you

back up your important music files beforehand.

To open a folder, use q/w to select it, and then press

ENTER.

Use q/w to select a music file, and press ENTER or

1 to start playback.

Playback starts and the following screen appears.

Folder1

1/17

02_Song_Track2

Artist

Album

01:12:34

00:10

MP3 128kbps 16bit/44.1kHz

• MP3 players containing music files that are managed with spe-

cial music software, and the iPod containing music files man-

aged with iTunes are not supported.

• Operation with all USB mass storage devices including the abil-

ity to power them is not guaranteed.

• Do not connect your USB mass storage device via a USB hub.

The USB mass storage device must be connected directly to the

AV receiver’s USB port.

• If the USB mass storage device contains a lot of data, the AV

receiver make take a while to read it.

• To return to the previous menu during playback,

press RETURN.

• To stop or pause playback, press 2 or 3, respec-

tively.

• To select the next song, press 6. To select the

beginning of the current song, press 7. To select

the previous song, press 7 twice.

• To fast forward the current song, press 4. To

fast reverse the current song, press 5.

• USB memory devices with security functions cannot be played.

Tip

• If you press DISPLAY, you can toggle between the play-

back screen and the list screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Zone 2

In addition to your main listening room, you can also enjoy playback in the other room, or as we call Multi Zone. And,

you can select a different source for each room.

Connecting Your Zone 2 Speakers to an

Amp in Zone 2

Connecting Zone 2

There are two ways you can connect Zone 2 speakers:

This setup allows 7.1-channel playback in your main lis-

1. Connect them directly to the AV receiver.

tening room and 2-channel stereo playback in Zone 2,

2. Connect them to an amp in Zone 2.

with a different source in each room.

Connecting Your Zone 2 Speakers Directly

to the AV receiver

Hookup

• Use an RCA audio cable to connect the AV receiver’s

This setup allows 5.1-channel playback in your main room

and 2-channel stereo playback in Zone 2, with a different

source in each room. This is called Powered Zone 2, as the

Zone 2 speakers are powered by the AV receiver. Note that

when Powered Zone 2 is turned off, you can enjoy 7.1-

channel playback in your main room.

ZONE 2 LINE OUT L/R jacks to an analog audio input on

your Zone 2 amp.

• Connect your Zone 2 speakers to the speaker terminals on

your Zone 2 amp.

Main room

To use this setup, you must set the “Powered Zone2”

setting to “Act” (➔ 69).

Hookup

AV receiver

• Connect your Zone 2 speakers to the AV receiver’s FRONT

WIDE/ZONE 2 L/R terminals.

Main room

Zone 2

AV receiver

Receiver/

integrated amp

Note

• The Zone 2 volume must be set on the Zone 2 amp.

Zone 2

Note

• With this setup, the Zone 2 volume is controlled by the AV

receiver.

• Powered Zone 2 cannot be used if “Speakers Type(Front)” is

set to “Bi-Amp” (➔ 44).

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Powered Zone 2

Using Zone 2

If you’ve connected your Zone 2 speakers to the AV

receiver, as explained in “Connecting Your Zone 2 Speak-

ers Directly to the AV receiver” (➔ 68), you must set the

“Powered Zone2” setting to “Act” (Activated).

This section explains how to turn Zone 2 on and off, how

to select an input source for Zone 2, and how to adjust the

volume for Zone 2.

Controlling Zone 2 from the AV receiver

Press RECEIVER followed by SETUP.

The main menu appears onscreen.

ZONE 2 indicator

Tip

OFF

• If the main menu doesn’t appear, make sure the appropri-

ate external input is selected on your TV.

Use q/w to select “Speaker Setup”, and then press

ENTER.

The “Speaker Setup” menu appears.

2. Speaker Setup

1. Speaker Settings

2. Speaker Configuration

3. Speaker Distance

4. Level Calibration

5. Equalizer Settings

6. THX Audio Setup

Input selector buttons

ZONE 2

To turn on Zone 2 and select an input source, press

ZONE 2 followed by an input selector button

within 8 seconds.

Use q/w to select “Speaker Settings”, and then

press ENTER.

The “Speaker Settings” menu appears.

Zone 2 turns on, the ZONE 2 indicator lights.

2–1. Speaker Settings

Speaker Impedance

Speakers Type(Front)

Powered Zone2

6ohms

Normal

Not Act

To select AM or FM, press TUNER input selector

and ZONE 2 repeatedly.

Use q/w to select “Powered Zone2”, and use e/r

To select the same source as that of the main room,

press ZONE 2 twice. “Zone 2 Selector: Source”

appears on the display.

to select:

`Not Act:

Use FRONT WIDE/ZONE 2 L/R terminals to

connect front wide speakers (Powered Zone 2

disabled).

To turn off Zone 2, press ZONE 2.

ZONE 2 indicator flashes.

Press OFF.

`Act:

The zone is turned off, and the ZONE 2 indicator

goes off.

Use FRONT WIDE/ZONE 2 L/R terminals to

connect Zone 2 speakers (Powered Zone 2

enabled).

Press SETUP.

The setup menu closes.

Note

• Powered Zone 2 cannot be used if “Speakers Type(Front)” is

set to “Bi-Amp” (➔ 44).

• This procedure can also be performed on the AV receiver by

using SETUP, arrow buttons, and ENTER.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Zone 2 with the Remote

Controller

Adjusting the Volume for Zone 2

■ Operating with the remote controller

STANDBY

Press ZONE2.

ZONE2

Use VOL q/w to adjust the volume.

INPUT

SELECTOR

■ Operating on the AV receiver

Press ZONE 2 (the ZONE 2 indicator and Zone 2

selector on the display flashes).

Note

Use –/+ within 8 seconds to adjust the volume.

• To control Zone 2, you must press the remote controller’s

ZONE2 first.

• ZONE2 turns red while Zone 2 is on.

If your Zone 2 speakers are connected to a receiver or inte-

grated amp in Zone 2, use its volume control to adjust the

volume.

Press ZONE2, then point the remote controller at

the AV receiver and press ON.

To select an input source for Zone 2, press

Muting Zone 2

ZONE2, followed by INPUT SELECTOR.

To select AM or FM, press TUNER input selector

and ZONE2 repeatedly.

■ Operating with the remote controller

Press ZONE2 followed by MUTING.

To turn off Zone 2, press ZONE2, followed by

STANDBY.

Tip

• To unmute, press ZONE2 followed by MUTING again.

Note

• Only analog input sources are output by the ZONE 2 LINE

OUT and FRONT WIDE/ZONE 2 L/R terminals. Digital input

sources are not output. If no sound is heard when an input source

is selected, check if it’s connected to an analog input.

• You cannot select different AM or FM radio stations for your

main room and Zone 2. The same AM/FM radio station will be

heard in each room. For example, if you have an FM station for

the main room, that station will also be used in Zone 2.

• When you connect Zone 2 speakers directly to the AV receiver,

listening modes that require surround back speakers or front high

speakers or front wide speakers (6.1/7.1), such as Dolby Digital

EX, DTS-ES, THX Select2 Cinema, Dolby Pro Logic IIz

Height, and Audyssey DSX™ are unavailable.

• When the input selector of Zone 2 is selected, power consump-

tion on standby mode slightly increases.

• While Zone 2 is on, u functions will not work.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling iPod & Other Components

Controlling iPod

Press DISPLAY to switch to Extended Mode .

Connecting the iPod Directly to the

USB Port

A list of your iPod model’s contents appears. To

open a folder, use q/w to select it, and then press

ENTER.

USB can be used to play music files stored on iPod/

iPhone, which can be plugged into the AV receiver’s USB

port.

Tip

• With the default settings, the iPod/iPhone can be manipu-

lated as Standard Mode

• Pressing DISPLAY again switches back to Standard

Mode.

Use q/w to select a music file, and press ENTER or

1 to start playback.

• To return to the previous menu during playback,

press RETURN.

• To stop or pause playback, press 2 or 3, respec-

tively.

• To select the next song, press 6. To select the

beginning of the current song, press 7. To select

the previous song, press 7 twice.

USB port

Playing Music Files on the iPod/iPhone

• To fast forward the current song, press 4. To

fast reverse the current song, press 5.

This section explains how to play music files on the iPod/

iPhone.

• To switch the repeat mode, press REPEAT. To

switch the random mode, press RANDOM.

DISPLAY

Standard Mode control

The content information is not displayed onscreen, but can

be manipulated using the iPod/iPhone or the Remote Con-

trol (NET/USB).

NET/USB

Note

• The audio of video content can be played back but no video will

be displayed onscreen.

ALBUM +/–

q/w, ENTER,

PLAYLISTe/r

Extended Mode control

The content information is displayed (lists are displayed)

onscreen, and you can select and manipulate the content

while looking at the screen.

RETURN

1, 3, 2, 5,

Top screen list:

4, 7, 6

• Playlists

• Artists

REPEAT

RANDOM

• Albums

• Genres

• Songs

• Composers

Press NET/USB repeatedly to select the USB

input.

• Shuffle Songs

• Now Playing

Compatible iPod models

Connect the USB cable that comes with the iPod/

Made for:

iPhone to the USB port at the front of the AV

• iPod touch (1st and 2nd generation)

• iPod classic

• iPod (5th generation)

• iPod nano (1st, 2nd, 3rd, 4th and 5th generation)

• All iPhone models

receiver.

• The USB indicator lights (➔ 9) if the AV receiver

is able to read the iPod/iPhone.

• The USB indicator flashes if the AV receiver can-

not read the iPod/iPhone.

iPod(STD)

Push “DISPLAY” button switch to Extended mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

The following iPod models are not supported in Standard

Mode. These iPod models can only be controlled in Extended

Mode.

When you disconnect the iPod/iPhone, the AV receiver stores

the mode. This means that if you disconnect when in

Extended Mode, the AV receiver will start in Extended Mode

when you next connect the iPod/iPhone.

• iPod (5th generation)

• iPod nano (1st generation)

Displays a list.

Plays all tracks in random order.

Displays information about currently playing track.

Connecting an Onkyo Dock

No. Onkyo Dock

UP-A1 Dock

(Universal Port Option Dock)

Cable

Note

Page

—

• When UP-A1 Dock that seated iPod is connected, 73

the power consumption on standby mode slightly

increases.

• You can control your iPod when PORT is

selected as the input source.

• See the UP-A1 Dock’s instruction manual for

more information.

RI Dock

Analog audio (RCA)

• See the RI Dock’s instruction manual for more

information.

To use u (Remote Interactive), you must

make an analog audio connection (RCA)

between the AV receiver and the RI Dock.

Component video

P^B/CB

PR/CR

Composite video

u cable

Models sold are different depending on the region.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Using Your iPod models Alarm Clock

You can use your iPod models Alarm Clock function to

automatically turn on your iPod and the AV receiver at a

specified time. The AV receiver’s input source will auto-

matically be set to the PORT selector.

Using the Onkyo Dock

Dock is sold separately.

For the latest information on the Onkyo Dock compo-

nents, see the Onkyo web site at:

Note

http://www.onkyo.com

• To use this function, your iPod must be in the UP-A1 Dock, and

the UP-A1 Dock must be connected to the AV receiver.

• This function works only in the Standard mode (➔ 75).

• When you use this function, be sure to set the AV receiver’s vol-

ume control to a suitable level.

Before using the Onkyo Dock components, update

your iPod with the latest software, available from the

Apple web site.

For supported iPod models, see the instruction man-

ual of the Onkyo Dock.

• When Zone 2 is turned on, you can’t use this function.

• You cannot use this function for sound effects on your iPod.

UP-A1 Dock

■ Charging Your iPod models Battery

The UP-A1 Dock charges your iPod models battery while

your iPod is in the UP-A1 Dock and connected to the

UNIVERSAL PORT jack on the AV receiver. While your

iPod is seated in the UP-A1 Dock, its battery will be

charged when the AV receiver is set to “On” or “Standby”.

With the UP-A1 Dock, you can easily play the music,

photo, or movie stored on your Apple iPod through the AV

receiver and enjoy great sound.

You can use the AV receiver’s remote controller to operate

your iPod.

Note

■ Basic Operation

• When UP-A1 Dock that seated iPod is connected, the power

consumption on standby mode slightly increases.

The AV receiver may take several seconds to startup, so

you might not hear the first few seconds of the first

song.

■ Status Messages

• PORT Reading

The AV receiver is checking the connection with the

dock.

• PORT Not Support

The AV receiver do not support the connected dock.

• PORT UP-A1

UP-A1 Dock is connected.

Auto Power On

If you start iPod playback while the AV receiver is on

Standby, the AV receiver will automatically turn on and

select your iPod as the input source.

Direct Change

If you start iPod playback while listening to another input

source, the AV receiver will automatically select your iPod

as the input source.

Using the AV receiver’s Remote Controller

You can use the AV receiver’s remote controller to control

basic iPod functions (➔ 74).

Note

• The AV receiver displays the message “UP-A1” for several sec-

onds after recognizing the UP-A1.

• When the status message is not displayed on the AV receiver’s

display, check the connection to your iPod.

■ Operating Notes

• Functionality depends on your iPod model and generation.

• Before selecting a different input source, stop iPod playback

to prevent the AV receiver from selecting the iPod input

source by mistake.

• If any accessories are connected to your iPod, the AV receiver

may not be able to select the input source properly.

• When connecting UP-A1 Dock to the radio tuner UP-HT1

with AUTO selected by the tuner’s Mode Selector switch, you

can switch the input source between UP-A1 Dock and the

tuner, by pressing PORT repeatedly on the front panel.

• While your iPod is in the UP-A1 Dock, its volume control has

no effect. If you adjust your iPod models volume control while

it’s in the UP-A1 Dock, make sure it’s not set too high before

you reconnect your headphones.

• The Auto Power On function will not work if you set your

iPod in the UP-A1 Dock while it is playing.

• When Zone 2 is turned on, you can’t use Auto Power On and

Direct Change functions.

• Do not turn off the power with the iPod still connected to this

unit via the UP-A1 Dock.

• Set your iPod in the UP-A1 Dock after the AV receiver turns

on.

Download from Www.Somanuals.com. All Manuals Search And Download.

RI Dock

■ Operating Notes

• Use the AV receiver’s volume control to adjust the playback

volume.

• While your iPod is inserted in the RI Dock, its volume control

has no effect. If you adjust your iPod models volume control

while it’s in the UP-A1 Dock, make sure it’s not set too high

before you reconnect your headphones.

With the RI Dock, you can easily play the music stored on

your Apple iPod through the AV receiver and enjoy great

sound, and watch iPod slideshows and videos on your TV.

In addition, the onscreen display (OSD) allows you to

view, navigate, and select your iPod model’s contents on

your TV, and with the supplied remote controller, you can

control your iPod from the comfort of your sofa. You can

even use the AV receiver’s remote controller to operate

your iPod.

Note

• On the 5th generation iPod and iPod nano, the click wheel is

disabled during playback.

Note

• Enter the appropriate remote control code before using the AV

receiver’s remote controller for the first time (➔ 77).

• Connect the RI Dock to the AV receiver with an u cable

(➔ 72).

Controlling Y o ur iPod

By pressing REMOTE MODE that’s been programmed

with the remote control code for your Dock, you can con-

trol your iPod in the Dock.

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/

DOCK”.

See “Entering Remote Control Codes” for details on

entering a remote control code (➔ 77).

See the Dock’s instruction manual for more information.

• Set the AV receiver’s Input Display to “DOCK” (➔ 27).

■ System Function

System On

When you turn on the AV receiver, the RI Dock and iPod

turn on automatically. In addition, when the RI Dock and

iPod are on, the AV receiver can be turned on by pressing

ON/STANDBY.

■ UP-A1 Dock

PORT is preprogrammed with the remote control code for

controlling a Dock with Universal Port connector.

You can control your iPod when “PORT” is selected as

the input source.

Auto Power On

If you press the remote controller’s 1 while the AV

receiver is on Standby, the AV receiver will automatically

turn on, select your iPod as the input source, and your

iPod will start playback.

Without the RI Control

You must enter a remote control code 82990 first (➔ 77).

■ RI Dock

Direct Change

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/

DOCK”.

If you start iPod playback while listening to another input

source, the AV receiver will automatically switch to the

input to which the RI Dock is connected.

Using the AV receiver’s Remote Controller

You can use the AV receiver’s remote controller to control

basic iPod functions.

• ON/STANDBY may not work with a remote control

code (without u). In this case, make an u connection

and enter a remote control code 81993 (with u).

With the RI Control

Using Your iPod models Alarm Clock

If you use the Alarm Clock function on your iPod to start

playback, the AV receiver will automatically turn on at the

specified time and select your iPod as the input source.

In this case, make an u connection and enter a remote

control code 81993 (with u).

• Set the AV receiver’s Input Display to “DOCK” (➔ 27).

Note

• Linked operations do not work with video playback or when the

alarm is set to play a sound.

• If you use your iPod with any other accessories, iPod playback

detection may not work.

• This function works only in the Standard mode (➔ 75).

Download from Www.Somanuals.com. All Manuals Search And Download.

✔: Available buttons

Press the appropriate REMOTE

MODE first.

Onkyo Dock

Buttons

ON, STANDBY

✔

TOP MENU

✔

q/w/e/rENTER

PLAYLISTe/r

1, 3, 2, 5, 4,

7, 6

REPEAT

✔

RANDOM

PLAY MODE

DISPLAY^*6

MUTING

ALBUM +/–

i VOL q/w

RETURN

✔

• With some iPod models, generations and RI Docks, certain buttons may not work as expected.

• For detailed operation of the iPod, please refer to the instruction manual of RI Dock.

This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Your iPod may not respond the first time you press this

button, in which case you should press it again.

This is because the remote controller transmits the On and Standby commands alternately, so if your iPod is already on, it will

remain on when the remote controller transmits an On command.

Similarly, if your iPod is already off, it will remain off when the remote controller transmits an Off command.

Press DISPLAY to change the following modes:

Standard mode

Nothing is displayed on your TV and you navigate and select your contents by using your iPod models display.

Only this mode can playback the video.

Extended mode (Music)

Playlists (artists, albums, songs, and so on) are displayed on your TV, and you can navigate and select your music while looking at

your TV.

Extended mode (Video)

Playlists (Movies, Music Videos, TV Shows, Video Podcasts, or Rentals) are displayed on your TV, and you can navigate and select

your video while looking at your TV.

In Extended mode (see ), PLAYLIST is used as the page jump button.

With the page modes, you can quickly locate your favorite songs even when your song lists, artist lists, and so on are very long.

Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod from the RI Dock or

Standard mode is selected.

TOP MENU works as a Mode button when used with a DS-A2 RI Dock.

DISPLAY turns on backlight for 30 seconds.

Note

• In Extended mode (see ), the playback will be continued even if the AV receiver is turned off.

• In Extended mode (see ), you cannot operate your iPod directly.

• In Extended mode (see ), it may take some time to acquire the contents.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

You can use the AV receiver’s remote controller

Use q/w to select remote mode, and then press

(RC-768M) to control your other AV components, includ-

ing those made by other manufacturers. This section

explains how to enter the remote control code (with the

default underlined) for a component that you want to con-

trol: DVD, TV, CD, etc.

ENTER.

The category selection menu appears.

8–1. Remote Mode Setup

TV/DVD

TV/VCR

• Learn commands directly from another component’s

remote controller (➔ 80).

Use q/w to select category, and then press

ENTER.

• Program ACTIVITIES to perform a sequence of up to 32

remote control actions (➔ 80).

The brand name input panel appears.

Preprogrammed Remote Control

Codes

8–1. Remote Mode Setup