Manual Calibration Instructions
For Models: Omega | Quantum | Paragon | Omega II | Quantum II | Paragon II | Alpine | Advance 200 |
Advance 300 | Advance 400 | Advance 500 | TSC2 | TSC3 | TSC4 | TSC5
If the unit has a “Select” button and not the “Enter” button use the select to
select the engineering mode on the screen.
IMPORTANT
F2
F1
Calories / Elevation
Speed / Pulse
Time
Speed
Elevation
Distance
Pulse/Laps
Calories
10.46
0.87
SPEED
DOWN
SPEED
DOWN
Distance / Laps
Time
INCLINE
UP
INCLINE
UP
INCLINE
SPEED
START
STOP
HOLD TO PAUSE
SLOW
DOWN
SELECT
STOP
SELECT
START
FAST
UP
SPEED
ELEVATION
Entering Diagnostics Mode
1
2
3
4
Turn the treadmill power to ON.
Place the safety key in position on the console.
Simultaneously press and hold the incline “+” (s) and speed “-” (t) buttons for about five seconds. (F1 & F2)
The console will beep and display the software version in the one of the two following windows;
For Models Omega II | Advance 200: in the Time window.
All other Models: in the Calories/Elevation window.
Do NOT stand on the running belt when calibrating. Use the guide rails instead.
WARNING
5
6
Press Start. The running belt should begin moving.
The Speed or Speed Pulse window will display the actual speed of the running belt. This should be
0.5mph.
7
This should be 0.5mph (+ or - .05). If the speed is not within the proper start range, adjust the speed cube located on
the lower control board. (F3)
Note: When adjusting the speed cube, turn the screw right to increase the speed and left to decrease the speed. Use small
increments as the speed cube is sensitive and will respond to each change.
DO NOT PUSH DOWN HARD ON THE SCREW.
TRANSFORMER
F3
SPEED CUBE
Tip: Another way to verify the speed is set correctly: Count the running belt revolutions per minute. At 0.5mph the running
belt should make 4 revolutions per minute for the Alpine and Advance 500 and 4.5 revolutions per minute for all other units.
To exit the Engineering menu, press and hold “Stop” for three seconds.
IMPORTANT
Manual Calibration | Pre Auto Cal _rev1.5 | 08/17/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Calibration Instructions
For Models: RT1 | T51 | T52 | T53 | T54 | T605 | T805 | CST3 | CST4 | CST5 | T25 | T35 | 1.2T | 2.2T | 3.2T | 4.2T | 5.2T | 30516 | T61 | T62 | T63 |
T64 | T50 | T70 | CST3.5 | CST4.5 | PST6 | PST8 | T650 | T805 | 30517 | T10K | 30518 | T95 | CST3.5x | CST3.6 | CST4.6 | PST Pro | PST6 | PST8 |
T71 | T72 | T73 | T74 | 1.3T | 2.3T | 5.3T | T4 | T6 | DT680 | LS925T | RST5.6 | RCT7.6 | 30519 | 30516 | 30517 | WT751 | WT951 | 610T | 620T | 700T |
720T | 730T | 820T | 830T | 930T
F3
F1
Distance / Laps
Time
Manual
Intervals
Race
Rolling
Weight Loss
Hill Run
HillClimb
THRZone
Custom1
Custom2
%
2
START
STOP
1 %
SELECT
1
mp
INCLINE
SPEED
F2
Entering the Engineering Mode
1
Turn the treadmill power to ON.
2
3
Place the safety key in position on the console.
Simultaneously press and hold (for about five seconds) the incline “+” (s) and speed “-” (t) buttons.(F1 & F2)
For Model RT1: Simultaneously press and hold the 1 and 10 quick speed buttons for about three seconds. (F3)
4
The console should beep three times and ENG0 (EN90) should be displayed.
This indicates you are in the engineering menu.
Note: if ENG0 (EN90) is not displayed, but ENG (EN9) is displayed with another number at the end, you are still in the
engineering menu. Use the “+” (s) or “-” (t) buttons to navigate to the correct menu. See following instructions.
Auto Calibration
Do NOT stand on the running belt when calibrating. Use the guide rails instead.
WARNING
After following the steps above you will have three steps left to complete the calibration process.
1
Press the speed “+” (s) or “-“ (t) buttons until ENG2 (EN92) is displayed.
For Model RT1: Press the “Enter” button untill the display reads “Auto Set”.
2
Press and hold the “Enter” button for about three seconds to select.
For Models 1.2T | 2.2T | 3.2T: Press and hold the “Select” button for about three seconds to select.
For Models T25 | T35: Press and hold the “Start” button for about three seconds to select.
For Model RT1: Press the “Start” button to select Auto Set mode. (F3)
3
Press the “Start” button to begin.
For Models 1.2T | 2.2T | 3.2T: Press the “Select” button to begin.
The running belt will begin moving and will automatically begin the auto-calibration sequence to properly set and store the
speed values. Upon successful calibration there will be four beeps and it will automatically exit the Engineering Mode and will
return to the original screen. The whole process will typically take about two minutes.
Auto Cal _rev1.5 | 08/17/07 JHP
Download from Www.Somanuals.com. All Manuals Search And Download.
|