Water Specialist
1” Control Valve Series Model: WS1EI
1.25” Control Valve Series Model: WS1.25EI
Operation and Instruction Manual for OEM Only.
Please Note: This operation and instruction manual is for the training of the
OEM and for the OEM to use to train their customers. This document is not
to be used as the complete system manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
WS1EI & WS1.25EI Manual
Table of Contents
Programming Instructions
Refer to 1.5&2L Manual
Control Valve Function and Cycles of Operation
Control Valve Function and Cycles of Operation 1 - 2
Drawings and Part Numbers
Front Cover and Drive Assembly
Drawings and Part Numbers 1
Drawings and Part Numbers 2a
Drawings and Part Numbers 2b
Drawings and Part Numbers 2c
WS1EI Drive Cap, Pistons and Spacer Stack
WS1.25EI Drive Cap, Pistons and Spacer Stack
WS1 & WS1.25 Identification Figure
FOR INFORMATION COMMON TO ALL 1” & 1.25” CONTROL VALVEaS REFER TO THE WS1&WS1.25 COMMON
INFORMATION MANUAL
The common manual contains the Table of Contents shown below
Other Drawings and Part Numbers
Compliance Table
Injector Cap, Injector Screen, Injector, Plug and O-ring
Injector Order Information
Injector Graphs US Units: Injector Draw, Slow Rinse and Total Flow Rates
Injector Graphs Metric Units: Injector Draw, Slow Rinse and Total Flow Rates
Refill Flow Control Assembly and Refill Port Plug
Drain Line – 3/4”
Drain Line – 1”
Water Meter, Meter Plug and Mixing Valve
Installation Fitting Assemblies
No page number
Drawings and Part Numbers 3a
Drawings and Part Numbers 3b
Drawings and Part Numbers 3c-3d
Drawings and Part Numbers 3e-3f
Drawings and Part Numbers 4
Drawings and Part Numbers 5
Drawings and Part Numbers 6
Drawings and Part Numbers 7
Drawings and Part Numbers 8a – 8b
Drawings and Part Numbers 9
Drawings and Part Numbers 10
Drawings and Part Numbers 11
Drawings and Part Numbers 12
Drawings and Part Numbers 13
General Information 1
Bypass Valve
Flow Diagrams – Service and Backwash
Flow Diagrams – Downflow and Upflow
Flow Diagrams – Rinse and Fill
WS1 Wrench
General Information
General Warnings (Must appear in OEM’s manual)
Specifications which must be included in OEM’s Manual
Quick Reference Specifications
General Information 1
General Information 2
General Information 2
Drive Assembly
General Information 3
Drive Cap Assembly, Main Piston and Regenerant Piston
Spacer Stack Assembly
General Information 3
General Information 4
Injector Cap, Screen, Injector Plug and Injector
Refill Flow Control Assembly or Refill Port Plug
Drain Line Flow Control and Fitting Assembly
Water Meter or Meter Plug
General Information 4
General Information 4
General Information 5
General Information 6
Mixing Valve
General Information 6
Installation Fitting Assemblies
General Information 6
Bypass Valve
Installation
General Information 7 - 8
Installation 1 - 2
Service Instructions
Troubleshooting
Limited Warranty
Service Instructions 1 - 5
Troubleshooting 1 - 2
Last Page
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Valve Function and Cycles of Operation • Page 1
WS1EI & WS1.25EI Manual
Control Valve Function and Cycles of Operation
This glass filled Noryl1 (or equivalent) fully automatic control valve is designed as the primary control center to direct and regulate
all cycles of a water softener or filter. The WS1EI and WS1.25EI control valves are only available in downflow regeneration. When
the WS1EI or WS1.25EI control valve is set up as a filter, the control valve can be set to perform downflow regeneration or simply
backwash. The control valve can be set to regenerate on demand (consumption of a predetermined amount of water) and/or as a
time clock (passage of a particular number of days). The control valve can be set so that a softener can meet the Water Quality
Association (WQA) Standard S100 or NSF/ANSI Standard 44 efficiency rating.
The control valve is compatible with a variety of regenerants and resin cleaners. The control valve is capable of routing the flow
of water in the necessary paths to regenerate or backwash water treatment systems. The injector regulates the flow of brine or
other regenerants. The control valve regulates the flow rates for backwashing, rinsing, and the replenishing of treated water into a
regenerant tank, when applicable.
The control valve uses no traditional fasteners (e.g. screws); instead clips, threaded caps, nuts and snap type latches are used. Caps
and nuts only need to be firmly hand tightened because radial seals are used. Tools required to service the valve include one small
blade screw driver, one large blade screw driver, pliers and a pair of hands. A plastic wrench is available which eliminates the need
for screwdrivers and pliers. Disassembly for servicing takes much less time than comparable products currently on the market.
Control valve installation is made easy because the distributor tube can be cut 12.7 mm (½”) above to 12.7 mm (½”) below the top
of tank thread. The distributor tube is held in place by an o-ring seal and the control valve also has a bayonet lock feature for upper
distributor baskets.
The AC adapter power pack comes with a 4.6 meter (15 foot) power cord and is designed for use with the control valve. The AC
adapter power pack is for dry location use only.
Table 1 shows the order of the cycles and available time for the WS1EI or WS1.25EI control valve. The WS1EI and WS1.25EI can
be used for downflow softener and filter applications as well as backwash-only filters.
Table 1
Regeneration Cycles and Times
WS1EI & WS1.25EI Cycles of Operation
Cycle
Range of times (min.)
1 - 20 or OFF
1 - 99 or OFF
1 - 20 or OFF
1 - 20 or OFF
1. Backwash 1st (upflow)
2. Regenerant Draw/Slow Rinse (downflow)
3. Backwash 2nd (upflow)
4. Fast Rinse (downflow)
5. Regenerant Refill (with treated water)
6. Service (downflow)
0.1 - 99.9 or OFF
1 Noryl is a trademark of General Electric.
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Valve Function and Cycles of Operation • Page 2
WS1EI & WS1.25EI Manual
The user can initiate manual regeneration. The user has the option to request the manual regeneration at the delayed regeneration
time or to have the regeneration occur immediately:
1. Pressing and releasing the REGEN button. “ ” will flash towards Regen on the display and the regeneration will occur at the
delayed regeneration time. The user can cancel the request by pressing and releasing the REGEN button.
2. Pressing and holding the REGEN button for approximately 3 seconds will immediately start the regeneration. The user cannot
cancel this request, except by resetting the control by pressing NEXT and REGEN buttons simultaneously for 3 seconds.
For additional software features and specific setup refer to the 1.5 & 2L manual for this software.
Download from Www.Somanuals.com. All Manuals Search And Download.
Drawings and Part Numbers • Page 1
WS1EI & WS1.25EI Manual
EI Front Cover and Drive Assembly
Order No. Description
V3175EI-01 WS1EI FRONT COVER ASSEMBLY
Drawing No.
Quantity
1
2
3
4
5
6
1
1
1
1
3
1
V3107-01
V3106-01
WS1 MOTOR
WS1 DRIVE BRACKET & SPRING CLIP
V3408EI-01 WS1THRU2L EI PC BOARD ALT
V3110
V3109
WS1 DRIVE REDUCING GEAR 12X36
WS1 DRIVE GEAR COVER
V3186
WS1 AC ADAPTER 110V-12V
V3186EU
V3186UK
V3186-01
WS1 AC ADAPTER 220-240V-12V EU
WS1 AC ADAPTER 220-240V-12V UK
WS1 AC ADAPTER CORD ONLY
Not Shown
1
AC Adapter
U.S.
120 V AC
60 Hz
12 V AC
500 mA
International
230V AC
50 Hz
12 V AC
500 mA
Supply Voltage
Supply Frequency
Output Voltage
Output Current
4
1
6
5
3
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WS1EI & WS1.25EI Manual
Drawings and Part Numbers • Page 2a
WS1EI Drive Cap Assembly, Downflow Piston, Regenerant Piston and Spacer Stack Assembly
Drawing No.
Order No.
V3005
Description
WS1 Spacer Stack Assembly
Drive Cap ASY
Quantity
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
V3004
V3178
WS1 Drive Back Plate
WS1 Piston Downflow ASY
WS1 Regenerant Piston
O-ring 228
V3011*
V3174
V3135
V3180
O-ring 337
V3105
O-ring 215 (Distributer Tube)
WS1 Body ASY Downflow
WS1 Mixing Valve Body ASY
V3001
Not Shown
1
V3001-02
*V3011 is labeled with DN.
Note: The regenerant piston is not used in backwash only applications.
3
1
Black Plug
2
5
7
4a
4
8
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Drawings and Part Numbers • Page 2b
WS1EI & WS1.25EI Manual
WS1.25EI Drive Cap Assembly, Downflow Piston, Regenerant Piston and Spacer Stack Assembly
Drawing No.
Order No.
V3430
V3004
V3178
V3407
V3174
V3135
V3180
V3358
V3357
V3020
Description
WS1.5 Spacer Stack Assembly
Quantity
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Drive Cap ASY
WS1 Drive Back Plate
WS1.5 Piston Downflow ASY
WS1 Regenerant Piston
O-ring 228
O-ring 337
O-ring 219 (Distributor Tube Opening 33.5 mm (1.32"))
O-ring 218 (Distributor Tube Opening 32 mm)
8
1
WS1.25 Body ASY Downflow
(Distributor Tube Opening 33.5 mm (1.32"))
V3020-01
V3020-02
V3020-03
WS1.25 Mixing Valve Body Downflow ASY
(Distributor Tube Opening 33.5 mm (1.32"))
Not Shown
1
WS1.25 Body ASY Downflow
(Distributor Tube Opening 32mm)
WS1.25 Mixing Valve Body Downflow ASY
(Distributor Tube Opening 32mm)
Note: The regenerant piston is not used in backwash only applications.
3
1
Grey Plug on all
WS1.25 bodies
*Grey Ring
*Grey Distributor
O-ring retainer
2
5
7
4
8
6
*Only for valves that have a
32mm Distributor Tube Opening
Download from Www.Somanuals.com. All Manuals Search And Download.
Drawings and Part Numbers • Page 2c
WS1EI & WS1.25EI Manual
WS1 & WS1.25 Identification Figure
WS1 with 1.050" Distributor Tube Opening Identification
Spacer Color:
Grey
1.25"
Black Plug
1.25"
Note: The WS1 downflow piston is a solid amber color.
WS1.25 with 1.32" Distributor Tube Opening Identification
Spacer Color:
Black
1.5"
Grey Plug
1.5"
WS1.25 with 32mm Distributor Tube Opening Identification
Spacer Color:
Black
1.5"
Grey Plug
Grey Ring
1.5"
Grey
Distributor
O-ring
Retainer
Download from Www.Somanuals.com. All Manuals Search And Download.
WS1EI & WS1.25EI Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
WS1EI & WS1.25EI Manual
FOR INFORMATION COMMON TO ALL 1” & 1.25” CONTROL VALVES REFER TO THE WS1&WS1.25 COMMON
INFORMATION MANUAL
The common manual contains the Table of Contents shown below
Other Drawings and Part Numbers
Compliance Table
Injector Cap, Injector Screen, Injector, Plug and O-ring
Injector Order Information
Injector Graphs US Units: Injector Draw, Slow Rinse and Total Flow Rates
Injector Graphs Metric Units: Injector Draw, Slow Rinse and Total Flow Rates
Refill Flow Control Assembly and Refill Port Plug
Drain Line – 3/4”
Drain Line – 1”
Water Meter, Meter Plug and Mixing Valve
Installation Fitting Assemblies
No page number
Drawings and Part Numbers 3a
Drawings and Part Numbers 3b
Drawings and Part Numbers 3c-3d
Drawings and Part Numbers 3e-3f
Drawings and Part Numbers 4
Drawings and Part Numbers 5
Drawings and Part Numbers 6
Drawings and Part Numbers 7
Drawings and Part Numbers 8a – 8b
Drawings and Part Numbers 9
Drawings and Part Numbers 10
Drawings and Part Numbers 11
Drawings and Part Numbers 12
Drawings and Part Numbers 13
General Information 1
Bypass Valve
Flow Diagrams – Service and Backwash
Flow Diagrams – Downflow and Upflow
Flow Diagrams – Rinse and Fill
WS1 Wrench
General Information
General Warnings (Must appear in OEM’s manual)
Specifications which must be included in OEM’s Manual
Quick Reference Specifications
General Information 1
General Information 2
General Information 2
Drive Assembly
General Information 3
Drive Cap Assembly, Main Piston and Regenerant Piston
Spacer Stack Assembly
General Information 3
General Information 4
Injector Cap, Screen, Injector Plug and Injector
Refill Flow Control Assembly or Refill Port Plug
Drain Line Flow Control and Fitting Assembly
Water Meter or Meter Plug
General Information 4
General Information 4
General Information 5
General Information 6
Mixing Valve
General Information 6
Installation Fitting Assemblies
General Information 6
Bypass Valve
Installation
General Information 7 - 8
Installation 1 - 2
Service Instructions
Troubleshooting
Limited Warranty
Service Instructions 1 - 5
Troubleshooting 1 - 2
Last Page
Download from Www.Somanuals.com. All Manuals Search And Download.
WS1EI & WS1.25EI Manual
Revision History:
11/12/07
DRAWINGS AND PART NUMBERS • PAGE 1
4
V3408EI-01 WS1THRU2L EI PC BOARD ALT
1
Form No. V3115EI – Updated 11/12/07
Download from Www.Somanuals.com. All Manuals Search And Download.
|