Professional Disc Jockey Products
DM3000X/DM3002X
DJ MIXERS
Owner’s Manual
©2001
Industries
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
VERY IMPORTANT
Please read this entire manual before connecting this unit to your system
For optimum performance:
·
·
The crossfader is a user replaceable item and subject to wear. Excessive force can wear out the fader quickly. This is not a
warranted item.
Never use spray cleaners on the slide controls. Residues cause excessive dirt build-up and this will void your warranty. In
normal use slide controls can last for many years. If they malfunction (usually because of a dirty or dusty environment) consult
a professional technician.
·
·
Always make sure that AC power is OFF while making any connections.
Use appropriate cables throughout your system. Do not use excessively long cables (i.e. over 50ft/14m) Be sure plugs and jacks
are tightly mated. Loose connections can cause hum, noise or intermittents that could easily damage your speakers. Make the
input and output connections with readily available low-capacitance stereo cables. Quality cable makes a big difference in
audio fidelity and punch. See your Numark dealer or an electronics or audio specialist store if you are not sure which cables to
get.
·
·
Never attempt to make any adjustments or repairs other than those described in this manual. Take the unit to your dealer or to
an authorized Numark Service Center.
ALWAYS remember: “TURN AMPS ON LAST AND OFF FIRST”. Begin with master faders or volume controls on minimum
and the amplifier gain/input control(s) down. Wait 8 to 10 seconds before turning up the volume. This prevents transients which
may cause severe speaker damage.
·
·
Use restraint when operating controls. Try to move them slowly. Rapid adjustments could damage speakers due to amplifier
clipping.
Avoid amplifier “clipping” at all costs: this occurs when the red LEDs (usually on the front panel of most professional power
amplifiers) start flashing. “Clipping” is when the power amplifier is distorting and working beyond it’s limits. Amplifier
distortion is THE major cause of speaker failure.
·
To prevent fire or shock hazard, do not expose the unit to rain or moisture. Never place cans of beer, soda, glasses of water or
anything wet on top of the unit!
Product Registration
Please record the serial number of your unit as shown on the back of the chassis as well as the name of the
dealer from whom you purchased the unit. Retain this information and your original purchase receipt for
your records. Please return the enclosed warranty card to register your unit with us.
MODEL: __________________________
SERIAL NUMBER:__________________
PURCHASED FROM:_________________________
DATE OF PURCHASE:________________________
- The Leader in DJ Technology
©2001
Industries
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
DM3000X/DM3002X
PROFESSIONAL DJ MIXERS
CONGRATULATIONS!
You have purchased the DM3000X/DM3002X Stereo Mixer by
. This mixer was developed
by DJs for you combining requested features in an easy to understand layout. Using the latest in circuit
design technology and our history of award winning development experience you can expect years of
reliable service from this product.
Careful attention to detail was provided in this unit. The DM3000X/DM3002X even has smooth
edges to ensure your fingers don’t get caught up in the mix. We hope you enjoy the
experience.
Thank you for purchasing NUMARK products!
FEATURES:
CROSSFADER
MONITORING
§
§
§
§
§
Crossfader Reverse (Hamster) Toggle with off position
Variable Slope Control
Channel Assign selectors
Fader Start (DM3002X only)
Transform Buttons w/action assignment (DM3002X
only)
§
Two Bar 12-Segment Display graph for Stereo Master
output
Split/Blend Cue selection
Push Button Cueing
Headphone Jacks for Both 1/4" and 1/8" Headphone
Plugs
§
§
§
§
Treble Middle and Bass KILL toggle (DM3002X only)
OUTPUTS
INPUTS
§
§
3-line, 3-phono, 1-mic input
Front Panel 1/4" Mic input with Bass, and Treble
controls
Rotary Bass, Middle & Treble -32dB "CUT" and +10dB
"Boost"
§
§
§
§
§
Monitor/Zone Level Control
Record output
PFL sampling output
Process Loop IN/OUT (DM3002XX only)
Fader Start (DM3002X only)
§
§
§
§
§
PFL cue monitoring with send out for sampling
PFL Gain Adjust
Individual PFL meters (DM3002X only)
Process insert looping on all channels including
microphone (DM3002X only)
- The Leader in DJ Technology
©2001
Industries
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
TABLE OF CONTENTS
Safety Measures
Important Information
Registration
2
3
3
Introduction
4
Description of the Features
Quick Setup Diagram
Block Diagram
6
9
10
11
12
Specifications
Warranty
- The Leader in DJ Technology
©2001
Industries
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
27
15
28
26
5
3
4
5
6
16
11
12
8
7
10
13
2
1
24
21
17
22
20
18
19
14
9
23
25
- The Leader in DJ Technology
©2001
Industries
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
MIXER FEATURES
INPUTS
CROSSFADER
1.
2.
Input faders - control individual source levels in the mix.
17. Crossfader - achieves clean segues between the two input channels
Input Toggle Switch (Transform) - selects which source will be live to
that channel based on what you have connected to the rear panel input
section. By removing the face panel the switch can be rotated into any
of eight positions.
selected by the Crossfader Assign.
18. Crossfader Slope – determines how quickly the audio from the
opposing side of the crossfader activates. A tight curve (right position)
turns on the opposing audio signal with very little crossfader movement.
A loose curve (left position) makes very long and smooth segues in
transition.
3.
4.
5.
Pre-fader Gain Control – adjusts the pre-fader volume for cleaner
sound. Use this in conjunction with the PFL Meter to adjust the audio to
an optimum level.
19. Hamster switch with Off position – reverses the direction of the
Channel EQ – adjusts the Treble, Middle, and Bass frequencies
respectively of the channel audio. Full rotation to the left creates a
“CUT” effect eliminating most of the sound from that frequency area.
crossfader. In the center position the crossfader is deactivated.
20. Crossfader Assign – channels 1 or 2 can be assigned to the left.
Channels 2 and 3 can be assigned to the right. If for example channels 1
and 3 were selected then "Hard left" selects Channel 1 and "Hard right"
selects Channel 3. With the crossfader centered, both assigned channels
are live. Use the crossfader for fast and seamless segues from one
selected channel to the other.
Process Loop (DM3002X only) – activates the external process loop to
the channel selected.
Note: All process loops go to the same output and return. By pressing
process on two channels at the same time, the audio will bleed through
to the each channel. Only use one process loop at a time!
Note: If channel 2 is selected on both sides, the crossfader will turn off
channel 2 in the left position and turn it on in the right position
6.
PFL Meter (DM3002X only) - used to adjust the PFL levels, accurately
match channel levels with the Pre-fader gain controls before mixing
them together. The idea is to properly match PFL inputs, not the input
with the stereo output meter!
Note: The crossfader is user replaceable in case of failure. Simply
unscrew the two large screws that hold it in place, lift it out and
disconnect its cable. Re-attach the new crossfader and screw the
mounting plate back onto the unit - you’re back in business!
MICROPHONE
21. Beat Lights – Indicate when strong bass beats are present to allow more
7.
Mic Gain Controls – controls the DJ Mic volume for the Neutrik™
“Combo” connector on the front panel.
accurate beat mixes.
22. Push Button transforms (DM3002X only)– By pressing these button
the crossfader channel will respond as determined by the transform
assign
8.
Treble and Bass Controls – for fine-tuning the tone of your voice on
both mics through the sound system. The controls are detented for
setting tone "flat". For best results, use a dynamic cardioid microphone.
23. Transform Assign (DM3002X only):
9.
¼” input connector - allows connection of a 1/4” microphone jack
directly into the mixer.
(IN) - When active the transform button will punch in the channel
assigned regardless of crossfader position. When punching in the
opposing channel will be eliminated.
HEADPHONE CUEING
10. Channel Cue Assign - are used to route Pre Fader Level (PFL) channel
audio to the Monitor Section. The channel faders do not control the
Cue volume.
(OUT) – When active transform button will eliminate audio assigned
24. KILL switches (DM3002X only)- By moving these toggle down or up
the marked frequency area will be removed. For instance is BASS is
pressed the bass beat will be removed, Highs might remove cymbals,
and middle might remove vocals.
11. Headphone Mix - controls the mix of PFL and PGM signals to your
headphones. When the slider is moved to the left, all you will hear is the
cue source. When the slider is all the way to the right, you will hear what
is playing through the master output. By blending, beats can be matched
exactly and segues can be smooth when a song is cued.
25. Fader Start (DM3002X only)– activates the crossfader to send play and
cue commands to your auto-start Numark CD player or other popular
brand. For fader start, attach your mixer to a remote start CD player
using industry standard 1/8”(3.5mm) cables. When you move the
crossfader toward the active channel, the attached CD player will start.
When it is moved away, that side will cue (similar to pressing the cue
button).
12. Headphone Level – adjusts cue volume.
13. Split/Blend Cue – controls how PFL and Program audio are sent to your
headphones. In split mode, the PFL audio can be heard in your left ear
and PGM audio can be heard in your right ear. In blend mode, both PFL
and PGM can be heard in both ears.
OTHER ITEMS
14. Headphone output – for your 1/4” or 1/8” headphones.
26. Stereo Auto Peak Hold Level Indicator- quickly and accurately tracks
level of audio output. The red LEDs show output overload. When using
as a master output meter, set the crossover, equalizer and power amp
inputs to avoid distortion at each step in the audio chain.
OUTPUTS
15. Master Fader – controls the overall output level.
27. Power Switch – Actives mixer power. Always turn on input devices
16. Panning - controls output to the left and right speakers. By rotating left
only the left speaker will be heard. By rotating right only the right
speaker will be heard.
first, the mixer second, and amplifiers last!
28. Light Connector – for attaching a 12V BNC style gooseneck light.
- The Leader in DJ Technology
©2001
Industries
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
REAR PANEL FEATURES
4
10
7
6
3
3
5
5
2
1
8
9
1. Power Input - to plug your power plug in before switching on power. See safety precautions on page 3 for proper treatment of power.
2. Voltage Selector – Set this to the appropriate power for your location. If unsure ask your authorized dealer.
3. Phono Inputs – plug your turntables in here.
4. Ground lug - use these connections with your turntables’ grounding cable to avoid signal hum.
5. Line Inputs - to connect stereo audio from HiFi VCRs, cassette and reel-to-reel tape decks, DAT machines, CD players, laser discs, tuners,
even synthesizers or other mixing consoles.
NOTE: Plug mono audio sources into both Left and Right inputs using a “Y" cable connector.
6. Channel Process (DM3002X only) – The output is determined by pushing the front panel process selectors next to each channel. The post
fader signal is sent to the send output. The send should then be plugged into your external processor. Plug you processor return into the
Return input. Set the output level of you processor to match the signal it receives from the send to ensure smooth activation. With proper
level adjustment you can create smooth transitions between processed and unprocessed signal.
Note: this mixer was design to use one processor for many channels, If more than one channel is selected than the signal will bleed across
the channels. This can be a desired effect if you wish to blend wet a dry signal. Sent signal is captured after the PFL gain and prior to EQ
and Pan adjustments allowing the user total control of the processed signal.
7. Channel PFL Send – this output contains the PFL signal you hear in your headphones. The send should be plugged into your sampler and
the signal returned through one of your inputs.
8. Record Outputs – Plug in your tape deck to record your mix. Audio level is determined by the channel inputs.
9. Unbalanced Main Outputs – program output controlled by the Master fader knob.
10. Fader Start Connector (DM3002X only) – to attach your mixer to a remote start equipped Numark CD player using industry standard
1/8”(3.5mm) cables. The fader start is design to work with all digital pulse style industry standard CD players
- The Leader in DJ Technology
©2001
Industries
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
QUICK SETUP DIAGRAM
Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all
input sources and processors. Next, connect your microphone and monitor headphones. Finally, connect the
stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC
power. Now you are ready to switch everything on. IMPORTANT: Always switch on your audio input
sources such as turntables or CD players first, then your mixer, and finally any amplifiers. When turning off,
always reverse this operation by turning off amplifiers, then your mixer, and then input devices.
- The Leader in DJ Technology
©2001
Industries
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
BLOCK DIAGRAM
- The Leader in DJ Technology
©2001
Industries
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DM3000X/DM3002X
SPECIFICATIONS
Inputs:
Line:
10K ohm input impedance
83mV rms sensitivity for 1.22V output
600 ohm input impedance unbalanced
1mV rms sensitivity for 1.22V output
65mV rms max input
Mic:
Phono: 47Kohm input impedance
1.3mV rms sensitivity @ 1KHz for 1.22V output
Outputs:
Line:
9V rms max
Headphone:
0.5W into 47ohm
Distortion:
less than 0.01%
Signal to Noise Ratio: (maximum output) JIS-A weighted
Line:
Mic:
Better than 92dB
Better than 82dB
Better than 85dB
Phono:
Frequency response:
Line:
Mic:
20Hz-20KHz +/-0.5dB
20Hz-15KHz +/-0.5dB
Phono:
+/-1dB except for controlled attenuation of -3dB
@ 20Hz to reduce rumble and feedback
Channel equalizer:
Bass:
+12/-32dB @40Hz
+12/-32dB @1.35KHz
+10/-28dB @15KHz
Middle:
Treble:
Channel Kill (DM3002X only):
Bass:
Better than 80dB at 40Hz
Middle:
Treble:
Better than 80dB at 1KHz
Better than 80dB at 15KHz
Power consumption:
16.7 Watt typical
21.2 Watt with full headphone output
254mm(W)x 355mm(D)x 90mm(H)
3.5 kgs
Dimensions:
Weight:
- The Leader in DJ Technology
©2001
Industries
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Professional Disc Jockey Products
LIMITED PRODUCT WARRANTY
What is covered and for how long?
1.
NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK products; including but not limited to DJ mixers, amplifiers, CD players, CD Mix
Stations, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, cartridges, and all other accessories; are to be free from defects in material and
workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer for a period of (1) Year.
What is not covered? This Limited Warranty is conditioned upon proper use of the product by the purchaser.
2.
This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress, modification of any part of the
product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces and other externally exposed parts that are scratched or
damaged due to normal use; (d) defects or damage from improper testing, operation, maintenance, installation, adjustment, or service of the mixers; (e) crossfaders.
What are NUMARK'S obligations? During the applicable warranty period, NUMARK will repair or replace, at NUMARK'S sole discretion, without charge to the purchaser, any
defective component part of the mixer. To obtain service under this Limited Warranty, purchaser must first contact NUMARK and obtain a return authorization number ("RA#").
Purchaser must then return the mixer to NUMARK in an adequate container for shipping, accompanied by purchaser's sales receipt or comparable proof of sale showing the date
of purchase, the serial number of the product, and the seller's name and address. To obtain an RA# and assistance on where to return the mixer, contact NUMARK customer
service at 401-295 9000. Upon receipt, NUMARK will repair or replace the defective products. NUMARK may, at NUMARK'S sole discretion, use rebuilt, reconditioned, or new
parts or components when repairing any product or replace a product with a rebuilt, reconditioned or new product. Repaired mixers will be warranted for a period equal to the
remainder of the original Limited Warranty on the original mixer or for (90) days, whichever is longer. All replaced parts, components, boards and equipment become the property
of NUMARK. If NUMARK determines that any mixer is not covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the repair or return of
such mixer.
3.
4.
What are the limits on NUMARK'S liabilities? THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED WARRANTIES COVERING
NUMARK MIXERS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NUMARK SHALL NOT BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR
OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY NUMARK MIXER, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT
LIMITED TO NUMARK'S OWN NEGLIGENCE, EVEN IF NUMARK OR ITS AGENT HAS BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST
PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK'S MIXERS, AND IS GIVEN IN LIEU OF ALL OTHER
EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES
PURCHASER'S EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL
ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER
ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
5.
6.
This Limited Warranty allocates risk of product failure between purchaser and NUMARK, and NUMARK'S product pricing reflects this allocation of risk and the limitations of liability
contained in this Limited Warranty. The agents, employees, distributors, and dealers of NUMARK are not authorized to make modifications to this Limited Warranty, or make
additional warranties binding on NUMARK. Accordingly, additional statements such as dealer advertising or presentation, whether oral or written, do not constitute warranties by
NUMARK and should not be relied upon.
How does state law apply to this warranty? SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER.
7. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction to another.
RETURN INFORMATION
a)
b)
c)
d)
A Return Authorization number must be obtained from Numark through the address or phone numbers below.
A copy of the original sales receipt must also be included for the equipment to be repaired under warranty.
The faulty equipment must be packed in its original packaging.
One additional outer layer of packaging must be included to ensure product safety. Failure to do so may inadequately protect the equipment in transit and, therefore,
jeopardize the customer’s warranty.
e)
f)
Numark will not accept COD shipments and no call tags will be issued for merchandise return.
Numark will not return repaired merchandise to customers by priority service, unless by written request at the customer’s cost. Requests must be submitted in writing
with merchandise returned.
g)
The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and original sales
receipt enclosed to:
INDUSTRIES
Attention: Service Department
11 Helmsman Avenue
Phone: +1 (401) 295-9000
Fax::
Web:
+1 (401) 295-5200
North Kingstown, RI 02852 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|