BROADBAND WITHOUT BOUNDARIES™
When all of your connections are made, the status LEDs on the front of your Netopia Router
will light, according to the following diagram:
Set up your Router
®
Netopia 4-Port ADSL Router
Power - Green when power is applied
1.After unpacking your Netopia Router shipping carton, decide where you want
to locate the Router.
DSL SYNC -
Models:
Netopia® 3346(EU, DE)-ENT / 3356(EU, DE)-ENT ADSL Routers – All Models
Flashes green when training
Solid green when trained
Flashes green for DSL traffic
You should install the Router near your PC or another location that permits easy access
and visibility. You can lay the Netopia Router flat or mount it on a wall. Make sure any
Ethernet cables are kept away from power cords, fluorescent lighting fixtures, and
other sources of electrical interference. Put the Router in a location where air can circu-
late freely around it.
Quickstart Guide
LAN 1, 2, 3, 4 -
Solid green when connected
to each port on the LAN.
Front View
Checklist
Flash green when there is
activity on each port.
2.Connect the power transformer to the power jack on the Router back panel.
Plug the power transformer into an appropriate electrical outlet.
Unpack your Gateway, check your package contents, and decide on a location:
•
•
Place the Gateway in a spot that is easily accessible for you.You can lay it flat or
mount on the wall.
Keep the cables away from other electrical devices that may interfere with the oper-
ation of your Gateway.
Turn on the power with the power switch. The Power light should come on solid green.
ConfigureYour PC for Dynamic Addressing
3.Connect the Router to the wall jack that supports your DSL service.
The following instructions assume that you want to use the automatic configuration and
address sharing features of the Router to provide IP information to devices on your local
Ethernet network.
Insert one end of the lavender telephone cable in the DSL port on the Router back
panel until you feel it lock. Insert the other end of the telephone cable into the tele-
phone jack connected to your ADSL service. The DSL SYNC indicator light should
blink for up to two minutes and then come on solid green.
1.Configure your computer to use an IP address on the same TCP/IP network as
the Netopia Router.
• Windows 95/98 or Windows ME:
Network Neighborhood
from the pull-down menu.
• Right-Click on the
Properties
icon on your Windows desktop and
10/100BT LAN
DSL
Power Supply
select
Rear View
• In the list of network components, highlight the entry that says
CD & Quickstart
Guide
Netopia Router
2
TCP/IP ([your Ethernet card here])
“
”.
4
3
LAN
2
1
Power
Off / On
DSL
Properties
• Click the
button.
Obtain an IP address automatically
• Click the
radio button. Click the DNS Con-
radio button. Click the Gateway tab and remove
button twice. When prompted, restart your PC.
Power Switch
Disable DNS
figuration tab. Click the
-or-
Power Supply
OK
any installed Gateways. Click the
4
International
North American
• Proceed to the next section “Configure Your Netopia Router”.
3
• Windows 2000 and XP
My Network Places
• Right-Click on the
Properties
icon on your Windows desktop and select
.
Local Area Connection
• Select your
.
4.Connect the Router to create your Ethernet local area network (LAN.)
Lavender RJ-11
Telephone Cable
Yellow RJ-45
Ethernet Cable
Local Area Connection
Properties
• Right click on your
and select
.
Connect the yellow Ethernet cable to your first PC and to the Router.
Internet Protocol [TCP/IP]
• Select
.
The LAN indicator light should come on solid green for the port where you connected
your Ethernet cable.
Properties
• Click the
• Click the
button.
If you don’t have everything, contact your supplier immediately.
Obtain IP address automatically
Obtain DNS
radio button and the
server address automatically
OK
button.
radio button. Click the
Connect each computer or other device to a switch port on the back of the Router with
an Ethernet cable (maximum length 100 meters). If you need more than four ports, con-
nect a hub or switch to the Router using a standard Ethernet cable.
• Proceed to the next section “Configure Your Netopia Router”.
1
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|