Model No. NTL06907.3
Serial No.
USER'S MANUAL
Write the serial number in the space
above for reference.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-825-2588
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over the age of 35 or persons
with pre-existing health problems.
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 12. To purchase a surge suppressor, see
your local NordicTrack dealer or call the tele-
phone number on the front cover of this man-
ual and order part number 146148, or see your
local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 26 if the treadmill is
not working properly.)
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should be used only by persons 16. Read, understand, and test the emergency
weighing 300 lbs. (136 kg) or less.
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 14).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. When connecting the power cord (see page
12), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
24. Inspect and properly tighten all parts of the
treadmill regularly.
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 24.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary NordicTrack®
A2105 treadmill. The A2105 treadmill offers a selection
of features designed to make your workouts at home
more enjoyable and effective. And when you’re not ex-
ercising, the unique A2105 treadmill can be folded up,
requiring less than half the floor space of other tread-
mills.
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Book Holder
Fan
Console
Accessory Tray
Handrail
Pulse Sensor
Key/Clip
Upright
Reset/Off
Circuit Breaker
Power Cord
Walking Belt
Foot Rail
Platform Cushion
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex keys
adjustable wrench
and your own Phillips screwdriver
and
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one
of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra
hardware may be included.
1" Tek Screw (2)–4
1/4" Star
Washer (10)–6
3/8" Star
Washer (9)–7
3/8" Nut (8)–3
Base Pad Spacer
(13)–2
1/4" x 1/2"
Bolt (7)–6
3/8" x 2" Bolt (4)–3
3/8" x 1 1/4" Bolt (5)–3
3/8" x 4 1/2" Bolt (6)–4
1. Make sure that the power cord is unplugged.
1
A
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (56) so that the treadmill is more stable;
do not fully fold the Frame yet.
B
38
Hole
83
56
81
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
2
Cut the tie securing the Upright Wire (38) to the
Base (83). Locate the tie in the indicated hole in
the Base, and use the tie to pull the Upright Wire
out of the hole.
Tie
13
81
Attach a Base Pad (81) to the Base (83) in the
location shown with a Base Pad Spacer (13) and
a 1" Tek Screw (2). Then, attach another Base
Pad (81) with only a 1" Tek Screw (2).
2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),
and the shipping bracket (C) from the Base (83).
Attach a Wheel (84) with the Bolt and the Nut
that you just removed. Do not overtighten the
Nut; the Wheel must turn freely. Discard the
shipping bracket.
2
Tie
38
83
Cut the tie off the Upright Wire (38).
4
84
C
8
3. Identify the Right Upright (78) and the Right
Upright Spacer (79), which are marked with
stickers. Insert the Upright Wire (38) through the
Right Upright Spacer as shown.
3
78
38
See the inset drawing. Tie the wire tie in the
Right Upright (78) securely around the end of
the Upright Wire (38). With the help of a second
person, hold the Right Upright near the Base
(83). Then, pull the other end of the wire tie until
the Upright Wire is routed completely through
the Right Upright.
38
79
83
78
Wire
Tie
38
4
4. Hold a Bolt Spacer (80) inside the lower end of
the Right Upright (78). Insert a 3/8" x 4 1/2" Bolt
(6) with a 3/8" Star Washer (9) into the Right
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (80), 3/8" x 4 1/2"
Bolt (6), and 3/8" Star Washer (9).
6
78
9
38
Hold the Right Upright Spacer (79) and the
Right Upright (78) against the Base (83). Be
careful not to pinch the Upright Wire (38).
Finger tighten the 3/8" x 4 1/2" Bolts (6); do not
fully tighten the Bolts yet.
80
80
77
79
Press a Base Endcap (77) into the Base (83).
83
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (56) so the treadmill is more stable; do
not fully fold the Frame yet.
5
B
A
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
83
81
56
Attach a Base Pad (81) to the Base (83) in the
location shown with a Base Pad Spacer (13) and
a 1" Tek Screw (2). Then, attach another Base
Pad (81) with only a 1" Tek Screw (2).
4
2
13
Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),
and the shipping bracket (C) from the Base (83).
Attach a Wheel (84) with the Bolt and the Nut
that you just removed. Do not overtighten the
Nut; the Wheel must turn freely. Discard the
shipping bracket.
84
2
81
8
C
6. With the help of a second person, hold a Bolt
Spacer (80) inside the lower end of the Left
Upright (74). Insert a 3/8" x 4 1/2" Bolt (6) with a
3/8" Star Washer (9) into the Left Upright and
the Bolt Spacer. Repeat this step with a second
Bolt Spacer (80), 3/8" x 4 1/2" Bolt (6), and 3/8"
Star Washer (9).
6
74
6
9
76
Orient the Left Upright (74) and the Left Upright
Spacer (76) as shown. Hold the Left Upright
Spacer and the Left Upright against the Base
(83). Finger tighten the two 3/8" x 4 1/2" Bolts
(6); do not fully tighten the Bolts yet.
80
80
77
83
Press a Base Endcap (77) into the Base (83).
With the help of a second person, tip the tread-
mill so that the Base (83) is flat on the floor.
7. Have a second person hold the Bridge (95) near
the Right Upright (78). Remove the wire tie from
the Upright Wire (38).
7
95
Connect the Upright Wire (38) to the Bridge Wire
(52). Make sure to connect the connectors
properly (see the inset drawing). The connec-
tors should slide together easily and snap
into place. If they do not, turn one connector and
try again. IF THE CONNECTORS ARE NOT
CONNECTED PROPERLY, THE CONSOLE
MAY BE DAMAGED WHEN THE POWER IS
TURNED ON.
52
38
78
Wire Tie
52
38
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Insert the indicated connectors into the Right
Upright (78).
8
95
Next, insert the fronts of the brackets on the
Bridge (95) into the Uprights (74, 78), and then
fully insert the brackets. Make sure that the plas-
tic edges of the Bridge (95) are inside the
Uprights.
7
Connectors
Front
7
10
Attach the Bridge (95) with six 1/4" x 1/2" Bolts
(7) and six 1/4" Star Washers (10); start the two
Bolts indicated by the arrows first before
starting the other four Bolts. Tighten all six
Bolts.
Edge
7
74
10
See steps 4 and 6. Tighten the four 3/8" x 4 1/2"
Bolts (6).
7
78
9. With the help of a second person, hold the con-
sole assembly near the Bridge (95). Connect the
Bridge Wire (52) to the console assembly wire.
Make sure to connect the connectors prop-
erly (see the inset drawing in step 7). The
connectors should slide together easily and
snap into place. If they do not, turn one connec-
tor and try again. IF THE CONNECTORS ARE
NOT CONNECTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE
9
Console
Assembly
101
52
95
POWER IS TURNED ON.
Connect the Console Ground Wire (101) to the
console assembly ground wire. Insert the wires
into the console assembly.
9
5
Attach the console assembly with three 3/8" x
1 1/4" Bolts (5) and three 3/8" Star Washers (9).
Be careful not to pinch the wires.
10. Identify the Storage Latch (53). Remove the tie
from the end of the tube. Make sure that the
sleeve has been slid over hole 1 and that the
Latch Knob (54) is locked into hole 1. Pull on
the sleeve to make sure that it is locked into
place.
10
54
Hole 1
53
Tube
Sleeve
9
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Raise the Frame (56) to the position shown.
Have a second person hold the Frame until
this step is completed.
11
56
Orient the Storage Latch (53) so that the large
barrel and the Latch Knob (54) are oriented as
shown.
8
4
Attach the Latch Bracket (109) and Storage Latch
(53) to the Base (83) with two 3/8" x 2" Bolts (4)
and two 3/8" Nuts (8).
53
54
Large
Barrel
Attach the upper end of the Storage Latch (53)
to the bracket on the Frame (56) with a 3/8" x 2"
Bolt (4) and a 3/8" Nut (8). Note: It may be nec-
essary to move the Frame back and forth to
align the Storage Latch with the bracket.
109
83
Lower the Frame (56) (see HOW TO LOWER
THE TREADMILL FOR USE on page 25).
8
4
12. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; the large hex key
is used to adjust the walking belt (see page 27).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
If you purchase the optional chest pulse sensor (see page 23), follow the steps below to install the re-
ceiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged.
Remove the indicated 1/2" Screws (1) and the
Access Door (87) from the Console Back (91).
2. Connect the wire on the receiver (A) to the indi-
Small
Screws
cated wire extending from the Console Back
(91). Hold the receiver so the small cylinder
is oriented as shown and is facing the
Console Back. Attach the receiver to the plastic
posts on the Access Door (87) with the two in-
cluded small screws.
91
A
87
Wire
Small
Cylinder
1
3. Make sure that no wires are pinched.
Reattach the Access Door (87) with the 1/2"
Screws (1). Discard the other wires included
with the receiver.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local NordicTrack dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Select Button
Navigation Buttons
Key
Clip
FEATURES OF THE CONSOLE
The console also features a fitness journal, which auto-
matically records and stores your exercise information
so that you can view your workout history and track
your progress.
This revolutionary treadmill console offers a selection
of features designed to make your workouts more ef-
fective and enjoyable. When you use the manual mode
of the console, you can change the speed and incline
of the treadmill with the touch of a button. As you exer-
cise, the console will display continuous exercise feed-
back. You can even measure your heart rate using the
handgrip pulse sensor or the optional chest pulse sen-
sor.
To turn on the power, follow the steps on page 14. To
personalize console settings, see page 14. To iden-
tify yourself as User 1 or User 2, see page 15. To use
the manual mode, see page 16. To use a preset
workout or a weight loss workout, see page 17. To
create a learn workout, see page 19. To use a learn
workout, see page 20. To view the fitness journal,
see page 22. To reset the fitness journal, see page
23.
In addition, the console features six preset workouts
and eight weight loss workouts. Each workout automat-
ically controls the speed and incline of the treadmill as it
guides you through an effective workout.
Note: If there is a sheet of clear plastic on the face
of the console, remove the plastic. To prevent dam-
age to the walking platform, wear clean athletic
shoes while using the treadmill. The first time you
use the treadmill, observe the alignment of the
walking belt, and center the walking belt if neces-
sary (see page 28).
You can even create two of your own learn workouts
and save them for future use.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
When you select the user mode, the word LOGIN
will appear in the display for a few seconds and
then the user mode menu will appear.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
Plug in the power cord
(see page 12). Next, lo-
Reset
Position
cate the reset/off circuit
breaker on the treadmill
frame near the power
cord. Switch the circuit
breaker to the reset posi-
tion.
Important: To highlight options within a menu,
press the up, down, left, or right Navigation
buttons. To select options within a menu, press
the Select button (see the drawing on page 13).
Note: To exit the user mode at any time, press the
Back button repeatedly until the manual mode is se-
lected (see page 16). To re-enter the user mode
from the manual mode, press the Select button.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the circuit
breaker to the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
23 to turn off the demo mode.
2. Enter user information.
To enter your user information, first highlight the
SETUP option and press the Select button. The
setup menu will then appear in the display.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 13)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the posi-
tion of the clip.
Next, highlight the SETUP USER 1 or SETUP USER
2 option and press the Select button. The user in-
formation menu will then appear in the display.
You can now enter your name and your weight.
Highlight the desired option in the menu and press
the Select button. A flashing cursor will appear in a
field in the display. To enter a number or letter
above the cursor, press the up and down
Navigation buttons. To move the cursor, press the
left and right Navigation buttons. When you have
finished entering the desired numbers or letters in
the field, press the Select button. Repeat this ac-
tion to enter all the desired user information. Note:
For more information about the RESET JOURNAL
option, see page 23.
HOW TO PERSONALIZE CONSOLE SETTINGS
The console has a user mode that allows you to desig-
nate yourself as User 1 or User 2, enter user informa-
tion before you begin exercising, and select console
settings. The user information you enter will also be
recorded and stored in the fitness journal, which allows
you to view your workout history (see HOW TO VIEW
THE FITNESS JOURNAL on page 22).
Follow the steps below to personalize console settings.
1. Select the user mode.
To select the user mode, press the Select button
(see the drawing on page 13). The console can
store information and keep track of workout history
for two different users.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To exit the user information menu, press the Back
button. The setup menu will then appear in the dis-
play.
To set the date, first press the left and right
Navigation buttons to highlight the month, day, or
year field. Then, press the up and down Navigation
buttons to select the desired month, day, or year.
3. Select a default user setting.
When you have finished setting the date, press the
Select button. The time setting will then appear in
the display.
The console can record, store, and load informa-
tion for two different users. The default user setting
allows you to choose the user information that will
be loaded and recorded when you turn on the con-
sole at the beginning of a workout session.
To set the time, first press the left and right
Navigation buttons to select the hour or minute
field. Then, press the up and down Navigation but-
tons to select the desired hour or minute; make
sure to select the correct AM or PM time in the
hour field. When you have finished setting the
time, press the Select button. The console will then
exit the user mode.
To select a default user setting, first highlight the
SELECT DEFAULT USER option in the setup
menu and press the Select button. A list of default
user options will then appear in the display.
To select a default user option, press the up and
down Navigation buttons until an arrow appears
next to the desired option. Then, press the Select
button. When you select an option, an “x” will ap-
pear in the box next to the selected option.
HOW TO IDENTIFY YOURSELF AS USER 1 OR
USER 2
The console can load information and keep track of the
workout history for two different users. To identify your-
self as User 1 or User 2 for a workout session, first
press the Select button and enter the user mode.
Note: You can also turn on or turn off the welcome
screen from this menu. If the SHOW WELCOME
SCREEN option is selected, then a welcome mes-
sage with the name of the selected user will ap-
pear in the display each time you turn on the con-
sole.
The word LOGIN will appear in the display for a few
seconds and then the user mode menu will appear.
Press the up and down Navigation buttons to highlight
USER 1 or USER 2. Note: If you have personalized
the console settings (see page 14), then the name you
entered will appear instead of USER 1 or USER 2.
To exit the default user menu, press the Back but-
ton. The setup menu will then appear in the dis-
play.
4. Set the date and time.
Setting the date and time will allow the console
to record your workout history accurately in the
fitness journal.
To set the date and time, first highlight the
CHANGE DATE OR TIME option in the setup
Then, press the Select button to confirm your choice.
menu and press the Select button. The date setting The console will then exit the user mode.
will then appear in the display.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
Follow your progress with the display.
As you walk or run on the treadmill, the display can
show the following workout information:
See HOW TO TURN ON THE POWER on page
14.
• The elapsed time.
2.
3.
Personalize console settings if desired.
• The distance that you have walked or run.
• The speed of the walking belt.
• The incline level of the treadmill.
See HOW TO PERSONALIZE CONSOLE SET-
TINGS on page 14.
Select the manual mode.
• The approximate number of calories you have
burned.
Each time you insert the key, the manual mode will
be selected. If you have selected a workout, press
the Classic Workouts Enter/Exit button to return to
the manual mode.
• The date.
• Your heart rate. Note: Your heart rate can be dis-
played only while you use the handgrip pulse
sensor or the optional chest pulse sensor.
• The display can also show an animation of a
runner. As you increase or decrease the speed
of the walking belt, the runner will speed up or
slow down.
4.
Start the walking belt and adjust the speed.
The console offers two display options. The display
option you select will determine which workout in-
formation is shown. Press the left or right
Navigation button repeatedly to select the desired
display option.
To start the walking belt, press the Start button, the
Speed + button, or one of the ten numbered speed
buttons. Note: After you press the buttons, it may
take a moment for the walking belt to reach the se-
lected speed.
If you press the Start button or the Speed + button,
the walking belt will begin to move at 1 mph. As
you exercise, change the speed of the walking belt
as desired by pressing the Speed + and – buttons.
Each time you press a button, the speed setting
will change by 0.1 mph; if you hold down a button,
the speed setting will change in increments of 0.5
mph. If you press one of the ten numbered speed
buttons, the walking belt will gradually increase in
speed until it reaches the selected speed setting.
Note: Regardless of which display mode you select,
the speed or incline setting will appear in the dis-
play for a few seconds each time you change the
setting. In addition, your heart rate will appear in the
display each time you use the handgrip pulse sen-
sor (see step 7 on page 17).
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, the
Speed + button, or one of the ten numbered speed
buttons.
Note: The console can display speed and distance
in either miles or kilometers. To find out which unit
of measurement is selected or to change the unit
of measurement, see THE INFORMATION MODE
on page 23. Note: For simplicity, all instructions
in this section refer to miles.
5.
Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase or decrease buttons, or one of the
six numbered percent grade buttons. Each time
you press a button, the incline will gradually adjust
until it reaches the selected incline setting.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Measure your heart rate if desired.
HOW TO USE A PRESET WORKOUT OR A WEIGHT
LOSS WORKOUT
You can measure your heart rate using either the
handgrip pulse sensor or the optional chest pulse
sensor (see page 23 for information about the op-
tional chest pulse sensor). Note: If you hold the
handgrip pulse sensor and wear the chest pulse
sensor at the same time, the console will not dis-
play your heart rate accurately.
1.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
14.
2.
Select the workout menu.
Before using
the handgrip
pulse sensor,
remove the
sheets of
To select the workout menu, press the Classic
Workouts Enter/Exit button. The workout menu will
then appear in the display.
3. Select a preset workout or a weight loss
workout.
clear plastic
from the metal
contacts. In
addition,
make sure
that your hands are clean.
Contacts
To select one of the six preset workouts or one of
the eight weight loss workouts, first press the left
and right Navigation buttons to highlight the PRE-
SET WORKOUTS option or the WEIGHT LOSS
WORKOUTS option, and then press the Select
button.
To measure your heart rate, stand on the foot
rails and hold the metal contacts on the handrail—
avoid moving your hands. When your pulse is de-
tected, a heart symbol will flash in the display, and
then your heart rate will be shown. For the most
accurate heart rate reading, continue to hold
the contacts for about 15 seconds.
Then, press the left and right or the up and down
Navigation buttons until the name of the desired
preset or weight loss workout appears in the dis-
play. Note: To return to a previous menu, press the
Back button. To return to the manual mode, press
the Classic Workouts Enter/Exit button.
Note: If you have selected a workout, then your
heart rate will be shown in a pulse display along
with other exercise information.
When you select a preset workout or a weight loss
workout, the display will show the name of the
workout, the workout time, the maximum incline
setting, and the maximum speed setting. In addi-
tion, a profile of the speed settings of the workout
will appear in the display.
8. Turn on the fan if desired.
The fan has high and low speed settings. Press the
Fan button repeatedly to select a fan speed or to
turn off the fan. Note: If the fan is on when the
walking belt stops, the fan will automatically turn off
after a few minutes.
9.
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when you fold the treadmill to the storage posi-
tion or you may damage the treadmill. Next, re-
move the key from the console and put it in a secure
place.
Each preset workout is divided into 30 one-minute
segments. Each weight loss workout is divided into
20, 30, 40, or 45 one-minute segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed setting
and/or incline setting may be programmed for con-
secutive segments.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. Important: If you do not
do this, the electrical components of the tread-
mill may wear prematurely.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
5.
Press the Start button to start the workout.
The workout will continue in this way until the small
arrow reaches the right end of the profile. The
walking belt will then slow to a stop.
A moment after you press the Start button, the
treadmill will automatically adjust to the first speed
and incline settings of the workout. Hold the
handrails and begin walking.
If the speed setting or incline level for the current
segment is too high or too low, you can override
the setting by pressing the Speed or Incline but-
tons; however, when the next segment begins, the
treadmill will automatically adjust to the speed
and incline settings for the next segment.
Follow your progress with the display.
When you select a preset workout or a weight loss
workout, the display will show the time remaining in
the workout, the distance you have walked or run,
the approximate number of calories you have
burned, the incline level, and the speed of the walk-
ing belt.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
In addition, a profile of the speed settings of the
workout will appear in the display. A small arrow
below the profile will indicate your progress.
6.
7.
8.
Measure your heart rate if desired.
See step 7 on page 17.
At the end of the first one-minute segment of the
workout, a series of tones will sound. If a different
speed setting and/or incline level is programmed
for the second segment, the speed setting and/or
incline level will flash in the display for a moment to
alert you. The treadmill will then automatically ad-
just to the speed and incline settings for the second
segment.
Turn on the fan if desired.
See step 8 on page 17.
When you are finished exercising, remove the
key from the console.
See step 9 on page 17.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
HOW TO CREATE A LEARN WORKOUT
Press the Start button to start the workout, and
program the desired settings.
1.
Insert the key into the console.
Each learn workout can have up to 40 one-minute
segments. You can program one speed setting and
one incline setting for each segment.
See HOW TO TURN ON THE POWER on page
14.
2.
Select the workout menu.
To program a speed setting for the first segment,
press the Speed + and – buttons or one of the
numbered speed buttons. To program an incline
setting for each segment, press the Incline in-
crease or decrease buttons, or one of the six num-
bered percent grade buttons.
To select the workout menu, press the Classic
Workouts Enter/Exit button. The workout menu will
then appear in the display.
3. Select a learn workout.
At the end of the first segment, the program will
store the current speed setting and the current in-
cline level in memory. Program a speed setting
and incline level for the second segment as de-
scribed above.
To select one of the two learn workouts, first press
the left and right Navigation buttons to highlight the
LEARN WORKOUTS option, and then press the
Select button.
Then, press the left and right or the up and down
Navigation buttons until the name of the desired
learn workout appears in the display. Note: To re-
turn to a previous menu, press the Back button. To
return to the manual mode, press the Classic
Workouts Enter/Exit button.
Continue exercising and programming speed and
incline settings for up to forty minutes. Press the
Stop button twice and then press the Classic
Workouts Enter/Exit button when you are finished
with your workout. The workout you created will
then be stored in memory.
5.
When you select a learn workout, the display
will show the name of the workout, the workout
time, the maximum incline, and the maximum
speed setting. In addition, a profile of the speed
settings of the workout will appear in the display.
When you are finished exercising, remove the
key from the console.
See step 9 on page 17.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A LEARN WORKOUT
Each learn workout can have up to 40 one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for consecutive segments.
1.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
14.
4.
5.
Press the Start button to start the workout.
2.
Select the workout menu.
A moment after you press the Start button, the
treadmill will automatically adjust to the first speed
and incline settings of the workout. Hold the
handrails and begin walking.
To select the workout menu, press the Classic
Workouts Enter/Exit button. The workout menu will
then appear in the display.
3. Select a learn workout.
Follow your progress with the display.
To select one of the two learn workouts, first press
the left and right Navigation buttons to highlight the
LEARN WORKOUTS option, and then press the
Select button.
When you select a learn workout, the display will
show the time remaining in the workout, the dis-
tance you have walked or run, the speed of the
walking belt, the incline level, and the approximate
number of calories you have burned.
Then, press the left and right or the up and down
Navigation buttons until the name of the desired
learn workout appears in the display. Note: To re-
turn to a previous menu, press the Back button. To
return to the manual mode, press the Classic
Workouts Enter/Exit button.
In addition, a profile of the speed settings of the
workout will appear in the display. A small arrow
below the profile will indicate your progress.
At the end of the first one-minute segment of the
workout, a series of tones will sound. If a different
speed setting and/or incline level is programmed
for the second segment, the speed setting and/or
incline level will flash in the display for a moment to
alert you. The treadmill will then automatically ad-
just to the speed and incline settings for the second
segment.
When you select a learn workout, the display
will show the name of the workout, the workout
time, the maximum incline setting, and the maxi-
mum speed setting. In addition, a profile of the
speed settings of the workout will appear in the dis-
play. Note: If only three segments of a profile ap-
pear in the display, see HOW TO CREATE A
LEARN WORKOUT on page 19.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
The workout will continue in this way until the small
arrow reaches the right end of the profile. The
walking belt will then slow to a stop.
length of the workout, first wait until the workout
ends. Then, press the Start button and program
speed and incline settings for as many additional seg-
ments as desired; learn workouts can have up to 40
segments. When you have added as many seg-
ments as desired, press the Stop button twice and
then press the Classic Workouts Enter/Exit button.
To decrease the length of the program, press the
Stop button twice at any time before the program
ends, and then press the Classic Workouts Enter/Exit
button.
If the speed setting or incline level for the current
segment is too high or too low, you can override
the setting by pressing the Speed or Incline but-
tons; however, when the next segment begins, the
treadmill will automatically adjust to the speed
and incline settings for the next segment.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
7.
8.
9.
Measure your heart rate if desired.
See step 7 on page 17.
Turn on the fan if desired.
See step 8 on page 17.
6. Change the workout if desired.
If desired, you can change the workout while using
it. To change the speed or incline setting for the
current segment, simply press the Speed or Incline
buttons. When the current segment ends, the new
setting will be saved in memory. To increase the
When you are finished exercising, remove the
key from the console.
See step 9 on page 17.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO VIEW THE FITNESS JOURNAL
1. Insert the key into the console.
To view exercise information for a different year,
press the up and down Navigation buttons to
change the year. Note: The fitness journal can
store information for 11 different years.
See HOW TO TURN ON THE POWER on page
14.
5. View exercise information by month.
2. Identify yourself as User 1 or User 2.
After a few seconds, the view month menu will ap-
pear in the display.
See page 15.
To view exercise information by month, press the
up and down Navigation buttons to highlight the
desired month in the right side of the display. Then,
press the Select button. The exercise information
for the selected month will appear in the display.
3.
Select the fitness journal.
To select the fitness journal, press the Fitness
Journal Open/Close button. The console will then
load the stored journal information for the selected
user.
6. View exercise information by week.
Note: As you view the fitness journal, press the
Back button at any time to return to the previous
menu or display.
After a few seconds, the view week menu will ap-
pear in the display.
To view exercise information by week, press the up
and down Navigation buttons to highlight the de-
sired week in the right side of the display. Then,
press the Select button. The exercise information
for the selected week will appear in the display.
The fitness journal can display the following exer-
cise information for the current year:
Time—The total number of hours you have walked
or run on the treadmill.
7. View exercise information by day.
Distance—The total distance you have walked or
run on the treadmill.
After a few seconds, the view day menu will ap-
pear in the display.
Calories—The total approximate number of calo-
ries you have burned.
To view exercise information by day, press the left
and right Navigation buttons until an arrow appears
above the desired day in the right side of the dis-
play. Then, press the Select button. The exercise
information for the selected day will appear in the
display.
Average Speed—Your average walking or running
speed.
Average Pace—Your average walking or running
pace in minutes per mile or per kilometer.
8. Continue to view the fitness journal as
desired.
Vertical Feet—The distance you have climbed in
feet or meters.
Repeat steps 3 through 6 to view exercise informa-
tion for the desired year, month, week, or day.
Weight—Your weight, as entered in your user in-
formation.
9. Exit the fitness journal.
4. View exercise information by year.
Press the Fitness Journal Open/Close button to
exit the fitness journal at any time.
When you select the fitness journal, the year totals
will appear in the display.
Note: To delete the exercise information stored in
the fitness journal, see HOW TO RESET THE FIT-
NESS JOURNAL on page 23.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO RESET THE FITNESS JOURNAL
1. Select the user mode.
THE INFORMATION MODE
The console features an information mode that keeps
track of treadmill usage information and allows you to
select a unit of measurement for the console.
See step 1 on page 14.
2. Reset the fitness journal.
To select the information mode, hold down the Stop
button, insert the key into the console, and then release
the Stop button. When the information mode is se-
lected, the following information will appear in the dis-
play:
To delete exercise information stored in the fitness
journal, first highlight the SETUP option and then
press the Select button. The setup menu will then
appear in the display.
The display will show the total number of hours that the
treadmill has been operated and the total number of
miles or kilometers that the walking belt has moved.
Next, highlight the SETUP USER 1 or SETUP
USER 2 option and press the Select button. The
user information menu will then appear in the dis-
play.
In addition, the display will show the selected unit of
measurement. The word “English” will appear for miles
or the word “Metric” will appear for kilometers. To
change the unit of measurement, press the Speed +
button.
Note: The console features a display demo mode, de-
signed to be used if the treadmill is displayed in a
store. While the demo mode is turned on, the console
will function normally when you plug in the power cord,
switch the circuit breaker to the reset position, and in-
sert the key into the console. However, when you re-
move the key, the displays will remain lit, although the
buttons will not function. If the demo mode is turned on,
the word “ON” will appear in display while the informa-
tion mode is selected. To turn on or turn off the demo
mode, press the Speed – button.
Then, highlight the RESET JOURNAL option and
press the Select button. A confirmation request will
appear in the display. To delete the information
stored in the fitness journal, use the left and right
Navigation buttons to highlight the RESET JOUR-
NAL option and press the Select button. To retain
the information stored in the fitness journal, high-
light the CANCEL option and press the Select but-
ton.
To exit the information mode, remove the key from the
console.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor offers hands-free oper-
ation as it tracks your heart rate during your workouts.
To purchase the optional chest pulse sensor, call
the telephone number on the front cover of this
manual.
After you press the Select button, the user informa-
tion menu will again appear in the display.
3. Exit the user mode.
Press the Back button repeatedly until you have ex-
ited the user information menus.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the pos-
sibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage
position. Make sure that the latch knob is locked in
the storage position.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° F (30° C).
Frame
Latch Knob
HOW TO MOVE THE TREADMILL
Frame
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
knob is locked in the storage position.
Handrail
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Base
Wheel
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your left hand.
Pull the latch knob to the left and hold it. It may be neces-
sary to push the frame forward as you pull the knob to
the left. Pivot the frame downward and release the latch
knob.
Latch Knob
2. Hold the metal frame firmly with both hands and lower
it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your
legs and keep your back straight.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 12. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the back cover of this manual.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
THE POWER CORD. Remove the three 3/4"
Screws (12) and carefully pivot the Hood (61) off.
12
61
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Locate the Reed Switch (71) and the Magnet (50)
on the left side of the Pulley (51). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If neces-
sary, loosen the 3/4" Reed Switch Screw (15),
move the Reed Switch slightly, and then retighten
the Screw. Reattach the Hood (not shown), and run
the treadmill for a few minutes to check for a cor-
rect speed reading.
1/8 in.
15
50
51
71
Top
View
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 23 to turn off the demo mode.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
rear roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
2–3 in.
Rear Roller Bolts
c. If the walking belt still slows when walked on, see the back cover of this manual.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left rear roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is centered.
a
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clock-
wise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each side
of the walking belt 2 to 3 in. (5 to 7 cm) off the
walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert
the key, and carefully walk on the treadmill for a
few minutes. Repeat until the walking belt is prop-
erly tightened.
b
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over the age of 35 or persons with pre-exist-
ing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exer-
cise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NTL06907.3
R0108A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
29
4
1
6
3
4
6
10
7
6
5
10
2
4
5
2
2
2
2
2
1
1
2
7
8
2
2
1
4
2
2
1
6
3
2
4
3
1
3
2
1
1
2
1
1
2
2
2
3
1
1/2" Screw
1" Tek Screw
Hex Key
3/8" x 2" Bolt
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
2
1
1
4
4
2
1
2
3
8
1
1
1
1
1
1
1
1
1
1
1
1
2
1
Front Roller/Pulley
Bridge Wire
Storage Latch
Latch Knob
Right Foot Rail
Frame
Rear Roller Bracket
Rear Roller
Left Rear Foot
Right Rear Foot
Hood
Drive Belt
Motor Bracket
Motor
Lift Frame
Wire Tie
Rear Roller Ground Wire
Power Cord
Power Cord Grommet
Controller
Reed Switch
Reed Switch Clip
Belly Pan
3/8" x 1 1/4" Bolt
3/8" x 4 1/2" Bolt
1/4" x 1/2" Bolt
3/8" Nut
3/8" Star Washer
1/4" Star Washer
3/4" Tek Screw
3/4" Screw
Base Pad Spacer
#8 x 1/2” Tek Screw
3/4" Reed Switch Screw
1 3/4" Screw
5/16" x 1 1/2" Bolt
5/16" x 3 5/8" Bolt
3/8" x 1 1/4" Bolt
Rear Roller Bolt
3/8" x 1 3/4" Motor Bolt
3/8" x 1 1/2" Bolt
3/8" x 1" Bolt
1/2" Ground Screw
1 1/4" Foot Rail Screw
1/4" x 3/8" Bolt
3/8" x 3/4" Bolt
3/8" x 4" Bolt
Belt Guide Screw
1/4" Washer
1/4" Lock Washer
3/8" Star Washer
1/4" Cage Nut
3/8" Jam Nut
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Left Upright
Incline Motor
Left Upright Spacer
Base Endcap
Right Upright
Right Upright Spacer
Bolt Spacer
Base Pad
Caution Decal
Base
Wheel
Releasable Tie
8" Tie
3/8" Flange Nut
5/16" Flange Nut
Hood Clip
Upright Wire
Cage Nut
Foot Rail Decal
Left Foot Rail
Warning Decal
Walking Platform Cushion
Walking Platform
Walking Belt
Access Door
Book Holder
Console
Console Fan
Console Back
Console Plastic Tie
Console Frame
Cup Holder
Bridge
Belt Guide
Handrail Base
Left Hand Grip
Right Hand Grip
Console Bracket
Key/Clip
Frame Endcap
Frame Spacer
Front Roller Spacer
Magnet
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
111
112
1
1
1
1
1
1
1
1
1
1
1
2
Console Ground Wire
Left Rear Foot Insert
Right Rear Foot Insert
Lift Motor Spacer
Filter Wire
Reset/Off Circuit Breaker
Lift Frame Ground Wire
5/32" Hex Key
Latch Bracket
15 1/2" Wire Tie
Latch Endcap
Rear Foot Washer
113
114
1
2
–
–
–
–
–
–
–
#8 x 1/2" Ground Screw
#8 x 1 1/2" Screw
10" Blue Wire, M/F
10" Blue Wire, 2F
6" Blue Wire, 2F
10" Red Wire, M/F
8" Black Wire, M/F
8" Green Wire, F/R
User’s Manual
*
*
*
*
*
*
*
*These parts are not illustrated.
Specifications are subject to change without notice.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. NTL06907.3
R0108A
1
1
1
7
8
4
4
5
2
9
4
6
6
0
3
4
4
5
9
2
2
3
4
0
5
1
5
5
2
9
4
8
4
7
5
4
5
6
5
5
2
6
5
3
2
5
4
7
5
6
3
9
2
3
0
6
2
1
4
5
1
2
1
4
4
4
1
0
1
4
3
4
1
4
5
2
2
8
2
4
6
5
3
0
3
1
4
2
2
8
7
4
1
0
5
1
1
1
5
1
2
32
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. NTL06907.3
R0108A
12
37
12
37
12
37
61
27
32
24
107
35
62
27
63
26
65
19
64
28
66
34
105
24
19
67
1
71
68
11
70
15
72
11
69
24
11
106
11
73
33
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C—Model No. NTL06907.3
R0108A
10
7
21
75
10
7
34
22
74
34
104
7
7
6
38
10
77
76
78
9
10
23
8
23
80
82
81
83
8
77
9
2
4
6
8
38
82
13
81
8
84
2
81
4
79
109
2
6
8
9
80
110
80
84
13
81
2
4
86
85
34
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING D—Model No. NTL06907.3
R0108A
1
91
88
90
87
1
1
1
12
1
1
1
89
1
1
1
14
39
14
93
12
1
1
39
92
100
94
95
1
1
52
1
16
1
33
9
96
1
97
33
99
33
1
52
99
113
101
5
1
16
33
98
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement parts(s) (see the PART LIST and the EXPLODED DRAW-
ING near the end of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame and drive motor are warranted for a life-
time. Parts and labor are warranted for one (1) year after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. This
warranty does not extend to any product or damage to a product caused by or attributable to freight
damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized
service center; to products used for commercial or rental purposes; or to products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 258733 R0108A
Printed in USA © 2008 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|