UM10044
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
Rev. 04 — 6 February 2007
User manual
Document information
Info
Content
Keywords
Abstract
isp1183, universal serial bus, usb
This document explains the ISP1183 PC eval kit.
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
1. Introduction
The ISP1183 is a cost- and feature-optimized Universal Serial Bus (USB) peripheral. It is
typically used in any microcontroller- or microprocessor-based system. The ISP1183 is a
full-speed USB Peripheral Controller with up to 14 configurable endpoints. It has a fast
general-purpose parallel interface to communicate with many types of microcontrollers or
microprocessors.
The ISP1183 has 2462 bytes of internal First In, First Out (FIFO) memory, which is
shared among enabled USB endpoints. The type and FIFO size of each endpoint can be
individually configured, depending on the required packet size. For increased data
throughput, isochronous and bulk endpoints are double-buffered.
To a microcontroller, the ISP1183 appears as a memory device with an 8-bit data bus
and a 1-bit address bus. The ISP1183 only supports a nonmultiplexed address and data
bus.
The ISP1183 PC evaluation (eval) kit uses two PCs as a complete USB development
environment, a host PC with USB host capability and a peripheral PC running the
ISP1183 firmware. The ISP1183 eval board is plugged in the peripheral PC as a USB
peripheral.
With this set up, you can easily evaluate the features of the ISP1183, and develop
firmware and product prototype, without being limited by the choice of a microcontroller.
The firmware is written in C, that supports Borland Turbo C for x86.
Fig 1 shows the ISP1183 eval board.
Fig 1. ISP1183 eval board
2. System requirements
For the host PC:
• PC with USB motherboard or add-on card.
• Microsoft Windows 98 and Windows 2000.
For the peripheral PC:
• PC with Microsoft DOS 6.x.
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
3 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
For the firmware development:
• x86 CPU platform: Borland Turbo C++ 3.0 or above.
• ISP1183 eval diskette.
Fig 2. System structure of the ISP1183 PC eval kit
3. Jumper settings on the ISP1183 eval board
The ISP1183 eval board is plugged into the peripheral PC. It will occupy I/O and IRQ
resources of the peripheral PC. To avoid possible conflicts in settings, remove all
unnecessary cards from the peripheral PC. Sound cards and network cards may cause
IRQ conflicts.
Jumper JP1 enables and disables the level-shift module.
Table 1.
JP1
Isolate data bus
Disable
Enable (default)
Short pins
1 - 2
2 - 3
JP2 sets the I/O power supply of the eval board. Default setting is 1.8 V.
Table 2.
JP2
I/O voltage select
1.8 V (default)
3.3 V
Short pins
1 - 2
2 - 3
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
4 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
JP4 sets the IRQ number for the ISP1183 eval board. Default setting is IRQ5 as shown
Table 3.
JP4
IRQ number
IRQ5 (default) IRQ3
5 - Intx_IRQ 3 - Intx_IRQ
IRQ4
IRQ6
IRQ7
Short pins
4 - Intx_IRQ
6 - Intx_IRQ
7 - Intx_IRQ
Jumper JP5 is reserved (left open).
Table 4.
S2
Microcontroller power supply
5 V (default)
3.3 V
Short pins
1 - 2
2 - 3
Table 5.
S4
Board power supply
Bus-powered
Self-powered (default)
Short pins
1 - 2
2 - 3
Table 6.
S5
VBUS power supply
Bus-powered (default)
Self-powered
Short pins
1 - 2
2 - 3
Table 7.
Possible conflict settings
IRQ number Possible conflict
IRQ5
IRQ7
Creative SoundBlaster and compatible sound cards always occupy this IRQ, by
default. If this type of sound card is installed, check its settings or remove it.
Some network cards may also use this IRQ.
Used by parallel port, by default. May cause printing problem on peripheral PC.
4. I/O mapping
The ISP1183 eval board occupies eight I/O locations. The base address is 368h.
Table 8.
Offset
I/O mapping
Usage
0
ISP1183 data register, read or write
Write command register, read data bus state
Board control and read chip I/O state
Reserved
1
2
3
4 to 7
Reserved for expansion board
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
5 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
5. Installing hardware, firmware, INF and driver
The procedure to install hardware, firmware, INF and driver is as follows:
1. Switch off the peripheral PC.
2. Remove all unnecessary cards on the peripheral PC.
3. Plug the ISP1183 eval board in the ISA slot of the peripheral PC.
4. Switch on the peripheral PC.
5. On the peripheral PC, under the DOS mode, run firmware 1183FW.EXE.
If it is the first time that the eval board is connected to the host PC, the host OS Device
Manager will prompt for the installation of INF and drivers.
6. Select the location of D13TEST.INF and D13TEST.SYS from the ISP1183 evaluation
diskette and complete the installation procedure.
6. Using the host applet
Fig 3. D13Test applet
Table 9 shows a description of endpoints operation on the ISP1183 eval board.
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
6 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
Table 9.
Description of endpoints operation
The test applet and the ISP1183 eval board support three test modes: loopback, print
and scan. The firmware uses I/O accesses on this endpoint.
Endpoint number
Endpoint type
ISO-OUT
ISO-IN
Operations
5
6
3
4
This pipe is defined as an isochronous OUT pipe.
This pipe is defined as an isochronous IN pipe.
This pipe is defined as a bulk OUT pipe. Supports DMA.
This pipe is defined as a bulk IN pipe. Supports DMA.
Bulk-OUT
Bulk-IN
Three test modes:
• Scan mode: In this mode, the ISP1183 eval board acts like a scanner. It sends data
packets to the host PC as fast as possible. Use this mode to evaluate the
isochronous IN and bulk IN transfer rates.
• Print mode: In this mode, the ISP1183 eval board acts like a printer. It receives data
packets from the host PC as fast as possible. Use this mode to evaluate the
isochronous OUT and bulk OUT transfer rates.
• Loopback mode: In this mode, the ISP1183 eval board receives data packets on the
isochronous OUT (or bulk OUT) endpoint and sends them back to the host PC on
isochronous IN (or bulk IN) endpoint. Use this mode to test the data integrity of
transfers.
The Buffer Size setting of the test applet is determined by firmware and hardware ability
of the eval board. For ISA mode, the maximum size is limited to 64000 bytes for the bulk
transfer and 256 bytes for the ISO transfer. For ISO scan mode, if you need to change
the buffer size, print a buffer of the same data size first. By default, Buffer Size is set to
64000 when the test applet is launched. Change Buffer Size to 64 before starting the
test.
Repeat Times for the loopback test controls the numbers of iterations of loopback, which
is useful for debugging. By default, Repeat Times is set to 0 when the test applet is
launched. To run the test infinite times, set Repeat Times to –1.
7. Testing control endpoints using standard USB compliance tool
To test control endpoints using the standard USB compliance tool:
1. Run the USB compliance tool.
2. Connect a USB peripheral.
1. In this document, names of windows and dialog boxes are indicated in italic.
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
7 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
Fig 4. USB Compliance Tool window
Fig 5. Device Framework Tests dialog box
2. In this document, items that you click or type are indicated in bold.
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
8 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
Wakeup and select In A Continuous Loop.
5. Click the Start Automated Testing button.
6. To stop the loop test, click Stop Testing.
Fig 6. Full Test Results dialog box
The USBCV testing tool can be downloaded from the USB website. Check the website
for the latest version of the tool.
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
9 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
8. Schematics
Power supply module
DC3
100 μF/10 V
CON6
D6
U9
D7
D3
self-power
ISA-5V
self-power
1
2
3
1
2
S4
S5
VDD
+5 V
Vin
V
CC
LM7805
IN5401
IN5401
IN5401
DGND
C35
VBUS_N
C36
C34
DGND
L3
VBUS
bus-power
220 μF/50 V
0.1 μF
100 μF
8~15V DC IN
BLM21P221SG
DC4
22 μF/10 V
C13
0.1 μF
V
CC(3V3)
V
(1V8)
V
(1V8)
JP2
V
CC(3V3)
DC1
L1
100 μF/10 V
L2
DC2
CDRH125-220
8
CDRH125-220
220 μF/10 V
U6
D1
1
2
3
4
Q2
220 pF
C7
OUT GND
FB3/5 EXT
SHDN CS
MBRS340T3
U7
R7
D2
Q3
1
2
3
4
8
7
7
6
5
OUT GND
10 kΩ,1%
R8
MMSF3PO2HD
1 kΩ
R29
MBRS340T3
FB3/5 EXT
SHDN CS
R9
26 kΩ,1%
MMSF3PO2HD
RSENSE2
100 Ω
R28
RSENSE1
,
6
5
C5
REF
V+
100 Ω
0.1 μF
, 1% 1/2W
0.04 Ω
MAX1626
REF
V+
V
CC
C6
0.47 μF
0.1 μF
0.04 Ω, 1% 1/2W
C8
V
CC
MAX1627
C9
0.47 μF
DC5
100 μF/10 V
47 μF/10 V
DC6
Fig 7. Power supply module
Level shift module
R18
JP1
V
V
CC(3V3)
CC(3V3)
U4
4.7 kΩ
U5
OE
INTX
VBUSONX 46
45
DREQ
SUSPEND43
48
47
1
48
1
OE
RDX
WRX
1OE
1A1
1A2
GND
DIR
1B1
1B2
GND
1B3
1B4
VCCB
1B5
1B6
1OE
1A1
1A2
GND
1A3
1A4
DIR
1B1
1B2
GND
1B3
1B4
2
BINTX
47
46
45
44
2
BRD
V
CC(3V3)
3
BVBUSON
3
BWR
4
4
44
5
DREQ'
BSUSPEND
5
CSX
BCS
BRST
1A3
1A4
VCCA
1A5
1A6
GND
1A7
1A8
2A1
2A2
GND
2A3
2A4
VCCA
2A5
2A6
GND
2A7
2A8
2OE
6
RSTX 43
42
6
C23
C24
0.1 μF
C19
C21
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
7
7
VCCA VCCB
8
41
40
39
38
8
WAKEUP
BWAKEUP
BA0
1A5
1A6
GND
1A7
1A8
2A1
2A2
GND
2A3
2A4
1B5
1B6
GND
1B7
1B8
2B1
2B2
GND
2B3
2B4
0.1 μF
0.1 μF
0.1 μF
9
A0
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
10
11
GND
1B7
TEST30
TEST31
DACK 37
UD7 36
UD6 35
34
UD5 33
UD4 32
31
12 DACK'
13 DB7
14 DB6
15
16 DB5
17 DB4
18
19 DB3
20 DB2
21
22 DB1
23 DB0
24 RDWR
1B8
2B1
2B2
GND
2B3
2B4
VCCB
2B5
2B6
GND
2B7
2B8
2DIR
C20
C22
VCCA VCCB
30
29
28
UD3
UD2
2A5
2A6
GND
2A7
2A8
2OE
2B5
2B6
GND
2B7
2B8
2DIR
0.1 μF
0.1 μF
UD1 27
UD0 26
25
OE
OE
25
P174AVC164245
P174AVC164245
Fig 8. Level shifter module
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
10 of 18
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
C17
ISP1183 USB module
C37
0.1 μF
0.1 μF
U1
RSTX 16
DACK 15
25
RESET_N
DACK
DGND
DATA4
DATA5
DATA6
DATA7
DD(1V8)
C10
18 pF
26 UD4
R33
DREQ 14
27 UD5
0 Ω
DREQ
3
3
Y4
R34
VBUSONX 13
VREG 12
28 UD6
Y2
VBUSDET_N
VBUS_OUT
ISP1183
2
C33
2
29 UD7
V
REG(3V3)
6 MHz
33 Ω
1
1
R11
A3
B4
C3
D4
U8
C18
0.1 μF
A1
B2
C1
D2
E1
11
30 V1V8
No load
V
A3
A1
B2
C1
D2
E1
AGND
DP
C11
0.1 μF
B4
C3
D4
E3
D+ 10
31 WAKEUP
18 pF
WAKEUP
D−
9
32 SUSPEND
E3
DM
SUSPEND
CON1
1
2
3
4
5
VBUS
EMIF02-USB02
VBUS
D−
22 Ω
R14
USBD−
USBD+
USBGND
D+
22 Ω
R15
GND
CHASSIS
C14
C16
22 pF
22 pF
USB_UPCON
C12
0.1 μF
0.027 μF, 2 kV
C15
VBUS_IN
1
2
4
6
8
2
4
6
8
1
3
5
7
9
3
VREG
D−−
D++
5
7
RSTX
CSX
9
10
10
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
TEST30
WRX
RDX
A0
WAKEUP
SUSPEND
UD0
DREQ
DACK
VBUSONX
GND
UD1
UD2
INTX
UD3
UD4
UD5
UD6
UD7
GND
CON4
MALE CONN 24 X 2
CON5
MALE CONN 24 X 2
Fig 9. ISP1183 USB module
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
11 of 18
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
CPLD module
C26
C28
C29
C30
C31
C27
C32
0.1 μF 0.1 μF 0.1 μF 0.1 μF
0.1 μF 0.1 μF
0.1 μF
V
CC(3V3)
U2
TCK
TDI
TMS
ALE
RESET
D6
48
83
TDO
TCK
45
TDO
TDI
47
22
41 ISA-ALE
32 D2
49 ISA-A4
50 ISA-A5
35 D0
TMS
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO/GCK1
23
IO/GCK2
27
IO/GCK3
13
DREQ'
BVBUSON
IO
53 ISA-A7
54 ISA-A8
37 ISA-A0
42 ISA-A3
60 ISA-A11
61 ISA-A12
52 ISA-A6
63 ISA-A13
55 ISA-A9
56 INTX_IRQ
65 DREQ''
58 ISA-A10
59 ISA-CLK
14
15
16
17
18
20
IO
IO
IO
IO
IO
IO
V
BINTX
RD#
WR#
CC(3V3)
Y3
C25
MWAKEUP
1
2
6
5
EN
V
CC
MRST
D7
D5
D4
D3
D1
ISA-EN
ISA-A1
ISA-A2
DB7
TEST31
BA0
0.1 μF
25 IO
NC
OE
28
29
30
IO
IO
IO
3
4
GND
O/P
24 MHZ
CPLD-CLK
R19
33 IO
36 IO
39 IO
XC95144XL-
7TQ 100C(100)
0 Ω
40
IO
99
66 ISA-A15
64 ISA-A14
71 ISA-IOW#
72 ISA-AEN
67 ISA-A16
76 ISA-D1
77 ISA-D2
68 ISA-IOR#
70 DACK''
81 ISA-D5
74 ISA-D0
82 ISA-D6
85 ISA-D7
78 ISA-D3
89 LED1
86 CPLD-CLK
90 RDWR
79 ISA-D4
80 ISA-RESET
34
43
46
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
NC
NC
NC
NC
NC
IO/GSR
3
4
1
6
8
9
10
11
12
87
91
92
93
94
95
96
97
IO/GTS1
IO/GTS2
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
V
CC(3V3)
DACK'
BWAKEUP
BRST
BCS
BWR
BRD
BSUSPEND
LED2
DB0
DB1
DB2
DB3
DB4
DB5
DB6
R20 R21 R22 R23
CON3
1
2
3
4
5
6
7
8
9
10
1 kΩ
1 kΩ 1 kΩ
1 kΩ
TCK
TDO
TDI
TMS
IO
FEMALE CON 1X10
2
7
19
24
NC
NC
NC
NC
73 ISA-IORDY#
Fig 10. CPLD module
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
12 of 18
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
ISA interface module
ISA-5V
CONN2
A1
A2
B1
IO CK#
D7
GND
RESET
+5V
B2
ISA-RESET
IRQ 9
ISA-D7
ISA-D6
ISA-D5
ISA-D4
ISA-D3
ISA-D2
ISA-D1
ISA-D0
ISA-IORDY#
ISA-AEN
A3
B3
D6
A4
B4
D5
IRQ9
A5
B5
D4
- 5V
A6
B6
DRQ2
D3
DRQ2
-12V
JP4
A7
B7
D2
IRQ7
A8
B8
ZERO-WAIT
ISA-12V
1
3
5
7
9
2
4
D1
OWS
IRQ6
IRQ5
IRQ4
IRQ3
A9
B9
D0
+12V
INTX_IRQ
A10
A11
A12
A13
A14
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
6
IORDY#
AEN
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
GND
MEMW#
MEMR#
ISA-IOW#
ISA-IOR#
DACK3#
DRQ3
DACK1
DRQ1
8
10
MEMW#
MEMR#
IOW#
IOR#
HEADER 5X2
ISA-A16 A15
ISA-A15 A16
ISA-A14 A17
ISA-A13 A18
ISA-A12 A19
ISA-A11 A20
ISA-A10 A21
DACK3#
DRQ3
DACK1#
DRQ1
REFRESH#
CLK
JP5
ISA-CLK
IRQ7
DACK1#
DACK2#
DACK3#
DRQ1
DRQ2
DRQ3
1
3
5
7
9
2
4
IRQ7
DACK''
ISA-A9
ISA-A8
ISA-A7
ISA-A6
ISA-A5
ISA-A4
ISA-A3
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
IRQ6
IRQ6
IRQ5
6
A8
IRQ5
IRQ4
8
10
11 12
A7
IRQ4
DREQ''
IRQ3
A6
IRQ3
DACK#2
D13-EOT
ISA-ALE
A5
DACK2#
TC
BALE
+5V
A4
HEADER 6X2
A3
A2
A1
OSC
GND
A0
AT62
Fig 11. ISA interface module
Indicator module
R24
LED1
LED2
4.7 kΩ
D4
LED2
R25
4.7 kΩ
D5
LED1
R27
330 Ω
R26
330 Ω
Q4
3904
Q5 3904
Fig 12. Indicator module
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
13 of 18
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
Microprocessor module
VCCM
S1
R1
1 kΩ
SW-PB
R2
C2
20 pF
C3
20 pF
C1
10 μF/16 V
Y1
S2
8.2 kΩ
R3
MCU-X1
MCU-X2
0 Ω
6 MHz
C4
U3
0.1 μF
RESET
9
40 VCCM
29
18 MCU-X2
17 RD#
16 WR#
11
VCC
PSEN
XTAL2
RST
XTAL1
MCU-X1 19
VCCM
BINTX
31
10
12
13
EA/VPP
RXD/P3.0
INT0/P3.2
INT1/P3.3
T0/P3.4
T1/P3.5
P0.0/AD0
P0.1/AD1
P0.2/AD2
P0.3/AD3
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
P1.0
RD/P3.7
WR/P3.6
TXD/P3.1
ALE/PROG
V
CC(3V3)
R4
30
ALE
14
15
39
38
37
36
35
34
33
32
1
28 MRST
P2.7/A15
P2.6/A14
P2.5/A13
P2.4/A12
P2.3/A11
P2.2/A10
P2.1/A9
P2.0/A8
P1.7
D0
27 MWAKEUP
26
25
D1
D2
R31
R5
D3
24
23
22
21
8
S6
100 kΩ 10 kΩ
10 kΩ
D4
R32
D5
10 kΩ
D6
D7
BVBUSON
7
P1.6
BSUSPEND2
ISA-EN
6
P1.1
P1.5
3
20
5
P1.2
P1.4
4
Q
1
VSS
P1.3
3904
DIP40
Fig 13. Microprocessor
9. Bill of materials
Table 10. Bill of materials
Used Part Type
Designator
C1
Footprint
CASE_C
0805
Description
Capacitor polar
Capacitor
1
10 µF/16 V
18 pF
2
C10 C11
24
0.1 µF
C12 C13 C17 C18 C19 C20 C21 C22
C23 C24 C25 C26 C27 C28 C29 C30
C31 C32 C33 C34 C37 C4 C5 C8
0805
Capacitor
2
1
2
1
1
2
1
1
22 pF
C14 C16
C15
0805
Capacitor
0.027 µF, 2 kV
20 pF
1206
Capacitor polar
Capacitor
C2 C3
C35
0805
220 µF/50 V
100 µF
-
Electrolytic capacitor
Electrolytic capacitor
Capacitor
C36
-
0.47 µF
C6 C9
C7
0805
220 pF
0805
Capacitor
USB_UPCON
CON1
USB_UPCON
USB upstream
connector
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
14 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
Used Part Type
Designator
Footprint
Description
Connector
Connector
DC-JACK
Gold finger
Schottky diode
Diode
1
2
1
1
2
3
1
1
1
3
1
1
5
1
1
2
1
3
2
6
1
2
3
2
1
2
3
1
3
1
FEMALE CON1 X 10 CON3
-
MALE CONN 24 X 2 CON4 CON5
-
8~15V DC IN
AT62
CON6
-
CONN2
-
MBRS340T3
IN5401
D1 D2
-
D3 D6 D7
-
LED2
D4
LED
LED
LED1
D5
LED
LED
220 µF/10 V
100 µF/10 V
22 µF/10 V
47 µF/10 V
-
DC1
-
Electrolytic capacitor
Electrolytic capacitor
Electrolytic capacitor
Electrolytic capacitor
Jumper
DC2 DC3 DC5
-
DC4
-
DC6
-
JP1 JP2 S2 S4 S5
-
HEADER 5X2
HEADER 6X2
CDRH125-220
BLM21P221SG
3904
JP4
-
Connector
Connector
Inductor
JP5
-
L1 L2
-
L3
1206
-
Inductor
Q1 Q4 Q5
Q2 Q3
NPN transistor
-
MMSF3PO2HD
1 kΩ
-
R1 R20 R21 R22 R23 R7
R11
0805
0805
0805
0805
0805
0805
0805
0805
0805
0805
-
Resistor
33 Ω
Resistor
22 Ω
R14 R15
R18 R24 R25
R19 R3
Resistor
4.7 kΩ
Resistor
0 Ω
Resistor
8.2 kΩ
R2
Resistor
330 Ω
R26 R27
R28 R30 R29
R31
Resistor
100 Ω
Resistor
100 kΩ
Resistor
10 kΩ
R32 R4 R5
R33
Resistor
0 Ω
Resistor
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
15 of 18
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
Used Part Type
Designator
Footprint
Description
Resistor (no load)
Resistor
1
1 MΩ (No load)
10 kΩ, 1 %
26 kΩ, 1 %
0.04,1 %, 1/2W
SW-PB
R34
0805
1
R8
0805
1
R9
0805
Resistor
2
Rsense1 Rsense2
S1 S6
-
-
-
-
2
Push-button
Test pad
99
-
TP1 TP10 TP100 TP101 TP102 TP104
TP11 TP12 TP13 TP14 TP15 TP16 TP17
TP18 TP19 TP2 TP20 TP21 TP22 TP23
TP24 TP25 TP26 TP27 TP28 TP29 TP3
TP30 TP31 TP32 TP33 TP34 TP35 TP36
TP37 TP38 TP39 TP4 TP40 TP41 TP42
TP43 TP47 TP48 TP49 TP5 TP50 TP51
TP52 TP53 TP54 TP55 TP56 TP57 TP58
TP59 TP6 TP60 TP61 TP62 TP63 TP64
TP65 TP66 TP67 TP68 TP69 TP7 TP70
TP71 TP72 TP73 TP74 TP75 TP76 TP77
TP78 TP79 TP8 TP80 TP81 TP82 TP83
TP84 TP85 TP87 TP88 TP89 TP9 TP90
TP91 TP92 TP93 TP94 TP95 TP96 TP97
TP98 TP99
1
1
1
2
1
ISP1183
U1
-
ISP1183
XC95144XL
DIP40
U2
SQFP14X14-100 (N)
CDIP40
CPLD
U3
Microcontroller
Level shift
PI74AVC164245
MAX1626
U4 U5
U6
TSSOP48
SO8
CMOS step-up
switching regulators
1
MAX1627
U7
SO8
CMOS step-up
switching regulators
1
1
2
1
1
EMIF02-USB02
LM7805
U8
EMIF02-USB02
-
U9
TO-3
-
6 MHz
Y1 Y2
Y3
-
Crystal
24 MHz
CSX-750
CN
-
-
No load
Y4
10. References
• ISP1183 Low-power Universal Serial Bus interface device with DMA data sheet
• Universal Serial Bus Specification Rev. 2.0
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
16 of 18
Download from Www.Somanuals.com. All Manuals Search And Download.
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
11. Legal information
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of a NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
11.1 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences
of use of such information.
therefore such inclusion and/or use is for the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
11.2 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations
or warranties, expressed or implied, as to the accuracy or completeness of
such information and shall have no liability for the consequences of use of
such information.
11.3 Trademarks
Notice: All referenced brands, product names, service names and
trademarks are property of their respective owners.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
UM10044_4
© NXP B.V. 2007. All rights reserved.
User manual
Rev. 04 — 6 February 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
17 of 18
UM10044
NXP Semiconductors
ISP1183 Low-Power USB Peripheral Controller PC Eval Kit
12. Contents
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in the section ‘Legal information’.
© NXP B.V. 2007. All rights reserved.
For sales office addresses, email to: [email protected].
Date of release: 6 February 2007
Document identifier: UM10044_4
Download from Www.Somanuals.com. All Manuals Search And Download.
|