®
© 2002 by NETGEAR, Inc. All rights reserved.
LEDs
START HERE
This table describes the activity of the Model GC102 Converter LEDs.
Trademarks
Congratulations on your purchase of the NETGEAR® Model GC102 Gigabit Ethernet Media Converter -a
cost-effective, high-performance network solution designed to enable flexible network design at gigabit
speeds.
©2002 NETGEAR, Inc. NETGEAR® , the Netgear Logo, the Gear Guy, and Everybody's connecting are
trademarks or registered trademark of Netgear, Inc. in the United States and/or other countries.
Microsoft, Windows, and the Windows logo are trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other countries. Other brand and product names are trademarks
or registered trademarks of their respective holders. Information is subject to change without notice. All
rights reserved.
Label
Color
Green
Activity
Description
This installation guide describes how to install and use the Model GC102 Gigabit Ethernet Media
Converter .
PWR(Power)
On
Power is supplied to the Converter.
Power is disconnected.
Off
LNK (Link)
Green
Green
On
A valid link is established on the port.
A link is not established on the port.
Statement of Conditions
FEATURES
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves
the right to make changes to the products described in this document without notice.
(located to the
right of each port)
Off
The Model GC102 Gigabit Converter has the following features:
One RJ-45 connector port, using Category 5 or better cable to deliver 1000BASE-T up to 100m (328 ft)
NETGEAR does not assume any liability that may occur due to the use or application of the product(s)
or circuit layout(s) described herein.
ACT (Activity)
On
Packet transmission or reception is
occuring on the port.
Certificate of the Manufacturer/Importer
One SC connector port, using 62.5/125 micron multimode fiber cable to deliver 1000BASE-SX up to
550m (1,804 ft)
It is hereby certified that the NETGEAR Model GC102 Converter has been suppressed in accordance
with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject
to certain restrictions. Please refer to the notes in the operating instructions. Federal Office
(located to the
right of each port)
Off
No traffic is passing through the port
Auto Uplink on the RJ-45 port to adjust for straight through or cross-over cables
Easy plug-and-play installation with no software to configure, which saves time and minimizes the poten-
tial for configuration errors.
for Telecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
Rear Panel
The rear panel of the Model GC102 Converter has a power adapter receptacle for the supplied power
adapter, as well as a switch to select flow control for the fiber port. If the switch is in the 'ON' position, the
GC102 will auto negotiate flow control on the SC connector. If the switch is in the 'OFF' position, the con-
verter will not use flow control or respond to any negotiation message.
Voluntary Control Council for Interference (VCCI) Statement
LEDs that provide network traffic and port status
This equipment is in the first category (information equipment to be used in commercial and/or industrial
areas) and conforms to the standards set by the Voluntary Control Council for Interference by Data
Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in
commercial and/or industrial areas.
IEEE 802.3x Flow Control standard compliance
Selector for Auto negotiation of flow control on the 1000BASE-SX port
Compact, sturdy metal case design that enables easy desktop, all-mount, or under-desk installaiton
Note: The converter will determine the switch setting when powering up. Once the converter is
operational, it ignores the switch position. If you want to change the setting, you must reset the
converter.
ꢀ
Consequently, when this equipment is used in a residential area or in an adjacent area thereto, radio
interference may be caused to equipment such as radios and TV receivers.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
PACKAGE CONTENTS
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not
installed and used in accordance with the instruction manual, it may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case users will be required to take whatever measures may be
necessary to correct the interference at their own expense.
ꢀ
Wall mounr
installation kit
adapter
EN 55 022 Statement
Installation guide,
Warranty & Owner
Registration Card,
and Support
This is to certify that the NETGEAR Model GC102 Converter is shielded against the generation of radio
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity
is declared by the application of EN 55 022 Class A (CISPR 22).
Information Card
Verify that your package contains the following:
Model GC102 Gigabit Ethernet Media Converter
Wall Mounting kit
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take appropriate measures.
APPLICATIONS
The Model GC102 Gigabit Ethernet Converter is designed to provide flexibility for your network design.
Converters can be used as a stand-alone device or can be used in a back-to-back configuration. The exam-
ples in this section illustrate some common network environments, using other NETGEAR products. These
examples focus on the benefit of the converter and do not show the workstations, servers, printers, and
routers that you would expect to find on a network.
This installation guide
Canadian Department of Communications Radio Interference Regulations
®
Warranty & Owner Registration Card
Support Information Card
The digital apparatus (NETGEAR Model GC102 Converter does not exceed the Class A limits for radio-
noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Power adapter
Although the examples illustrate specific NETGEAR switches, any switches can be used in the network con-
figurations shown.
ꢀ Note: Do not remove the dust cover from the fiber port until you are ready to connect the fiber optic
Réglement sur le brouillage radioélectrique du ministère des Communications
cable. Dust contamination can degrade the performance of the port and the media converter.
Cet appareil numérique (NETGEAR Modle GC102 Converter respecte les limites de bruits radioélec-
triques visant les appareils numériques de classe A prescrites dans les Réglementations sur le brouillage
radioélectrique du Ministère des Communications du Canada.
NETGEAR, Inc.
Stand alone configuration
4500 Great America Parkway
Santa Clara, CA 95054
USA
The GC102 can be used in to convert a fiber connection from a distant wiring closet to the desired copper
gigabit connection that is needed. In this example, a GS524T is able to support a distant FS750 with an
AG711F Fiber Gigabit module in it by using the GC102.
PRODUCT ILLUSTRATION
Copper Gigabit Ethetnet Port
Support: 1-888-NETGEAR
E-mail: support@NETGEAR.com
The RJ-45 port provides 1000BASE-T connectivity over Category 5 (Cat5) or better (Cat5e, Cat6)
unshielded twisted pair (UTP) cables for a distance up to 100 m (328 ft).
With Auto Uplink technology, the GC102 automatically adjusts for either straight-through or crossover
cables to make the right link.
Fiber Gigabit Ethernet Port
The SC port provides 1000BASE-SX connectivity over 62.5/125 micron multimode fiber cable for a dis-
tance up to 550m (1,804 ft). Be sure to match up the transmit and receive portions on the converter to
the correct parts of the plug.
M-GC102NA-0
M 1- G C 1 0 2 N A - 0
Download from Www.Somanuals.com. All Manuals Search And Download.
|